Siig 2-port external Serial ATA II (eSATA) PCI controller
Contents
1. Since the design of computer cases and motherboards vary refer to your computer s reference manual for further information if needed Static Electricity Discharge may permanently damage your system Discharge any static electricity build up in your body by touching your computer s case for a few seconds Avoid any contact with internal parts and handle cards only by their external edges 2 1 Turn OFF the power to your computer and any other connected peripheral devices 2 Unplug the power cord from the back of the computer 3 Remove your computer s cover e Remove the slot bracket from an available PCI slot 5 To install the card carefully align the card s bus connector with the selected PCI slot on the motherboard Push the board down firmly but gently until it is well seated 6 Replace the slot bracket s holding screw to secure the card 7 If needed connect the HDD LED pins to monitor HDD activity from the front panel of your chassis 8 Replace the computer cover and reconnect the power cord Driver Installation This section provides information on how to install the eSATA II 150 PCI drivers for the following operating systems Windows 2000 New Windows 2000 Installation A new installation of Windows 2000 requires a floppy disk for the driver installation To make this floppy disk copy the contents of the Floppy folder found on the driver CD onto a blank floppy disk then follow the direct2. manual Hot Plugging Hard Disk Drives To remove a drive from a powered up system do the following 1 Right click My Computer and click Manage 2 Select Device Manager 3 Click Disk Drives right click the target disk and select Disable Enable 4 You can now remove the target disk BIOS Configuration The eSATA II 150 PCI BIOS will appear everytime your system starts up If the bios doesn t show please try your controller in another PCI slot During this Post process the BIOS will show up and indicate the devices attached to it Technical Support and Warranty QUESTIONS SIIG s Online Support has answers Simply visit our website at www siig com and click on Support Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away You can also submit questions online and one of our technical support analysts will promptly respond A lifetime manufacturer warranty supplied with this product is offered by SHG Inc Please see SIIG website for more warranty details If you should happen to encounter any problems with this product please follow the procedures below If it is within the store s return policy period please return the product to the store where you purchased from If your purchase has passed the store s return policy period please follow these steps to have the product repaired or replaced Step 1 Submit your RMA request Go t
3. dows Setup screen press F6 to install the driver 4 Insert the driver diskette Press S then press Enter 5 Select INITIO INIC1620 S ATA Adapter For Windows XP 2003 and press Enter 6 Press Enter to continue and follow on screen instructions to complete the installation Existing Windows XP Server 2003 Installation 1 Install the board and boot up Windows 2 At the Found New Hardware Wizard XP w SP1or earlier Server 2003 Continue to step 3 XP w SP2 or later Server 2003 w SP1or later Select No not at this time then click Next 3 Insert the driver CD select Install the software automatically Recommended then click Next Click Next again to continue 4 Click Continue Anyway then click Finish Note Our driver has been thoroughly tested in Windows for stability 5 Restart Windows to complete the driver installation To Verify Windows 2000 XP 2003 Installation 1 Right click My Computer click Manage and select Device Manager 2 Double click SCSI and RAID Controllers then double click Initio inic1620 S ATA Adapter A message This device is working properly is displayed in the dialog box the driver has been correctly installed External Device Connection External Serial ATA devices should come with their own accessories In most cases you just need to power up the external device and connect it to the external port For more information please refer to the external device s
4. e of installation and compatibility of our products as well as one of the lowest defective return rates in the industry SIIG products can be found in computer retail stores mail order catalogs and e commerce sites in the Americas and the UK as well as through major distributors system integrators and VARs PRODUCT NAME eSATA II 150 PCI FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCESTATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SUG Inc 6078 Stewart Ave Fremont CA 94538 3152 eSATA II 150 PCI is a trademark of SHG Inc SIIG and SIIG logo are registered trademarks of SIIG Inc Microsoft and Windows are registered trademarks of Microsoft Corporation Othernamesused in publication are for identification only and may be trademarks of their respective companies January 2006 Copyright 2005 by SHG Inc All rights reserved
5. f eSATA II 150 PCI J Quick Installation Guide Introducing the eSATA II 150 PCI The eSATA II 150 PCI is an ultra high speed dual channel Serial ATA Generation 2 controller for usein PCI enabled systems Features and Benefits Adds two external eSATA ports to your desktop computer for external drive connections New Serial ATA cable easier to install amp provides better air circulation Supports two SATA channels and data transfer rate up to 1 5Gb s 150MB s Supports Native Command Queuing NCQ and SATA TCQ commands Onboard bus master engine relieves the system processor from book keeping and enhances performance Features independent 256 byte FIFOs per channel for host reads and writes Breaks the 137GB barrier Works with various brands of large capacity Serial ATA hard disks Supports SATA hard disk hot plugging Compliant with PCI2 3 andeSATA externalSATA connector specifications Compliant with Serial ATA 1 0 specifications and complement of SATA II optional features 04 0411A 1 System Requirements e Pentium or equivalent PC with an available PCI slot e Windows 2000 XP Server 2003 Package Contents eSATA II 150 PCI Driver CD e This quick installation guide Layout HDD LED pins Front chassis LED connects horizontally HDD Activity LED External connectors Figure 1 eSATA II 150 PCI Board Layout Hardware Installation General instructions for installing the card are provided below
6. ions below 1 Install the board and follow the Microsoft procedures to install Windows 2000 accordingly Restart your system when prompted during Windows installation At the Windows 2000 Setup screen press F6 to install the driver Insert the driver diskette Press S then press Enter Select INITIO INIC1620 S ATA Adapter For Windows 2000 and press Enter Press Enter to continue and follow on screen instructions to complete the installation Existing Windows 2000 Installation 1 Install the board and boot up Windows 2 At the Found New Hardware Wizard click Next 3 Select Search for a suitable driver for my device recommended and click Next 4 Insertthe driver CD check CD ROM drives uncheck the other boxes and click Next Click Next again to continue 5 Click Yes then click Finish Note Our driver has been thoroughly tested in Windows for stability 6 Restart Windows to complete the driver installation Windows XP Server 2003 New Windows XP Server 2003 Installation A new installation of Windows XP Server 2003 requires a floppy disk for the driver installation To make this floppy disk copy the contents of the Floppy folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Install the board and follow the Microsoft procedures to install Windows accordingly 2 Restart your system when prompted by Windows installation 3 Atthe Win
7. o www siig com click Support then RMA to submit a request to SIG RMA If the product is determined to be defective an RMA number willbe issued SIIG RMA department can also be reached at 510 413 5333 Step 2 After obtaining an RMA number ship the product Properly pack the product for shipping All software cable s and any other accessories that came with the original package must be included e Clearly write your RMA number on the top of the returned package SIIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e You are responsible for the cost of shipping the product to SIIG at the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 RMA e SIIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer About SIIG Inc Founded in1985 SHG Inc isaleading computer upgrade manufacturer of 1 Oconnectivity products including PCI amp ISA serial and parallel ports USB Serial ATA amp UltraATA controllers FireWire 1394a b Networking Sound Cards and other accessories SIIG is the premier one stop source of upgrades SIIG products offer comprehensive user manuals many user friendly features and are backed by an extensive manufacturer warranty High quality control standards are evident by the overall eas
Download Pdf Manuals
Related Search