JBL CONTROL® SERIES Control One
Contents
1. OWNER S GUIDE JBL CONTROL MONITOR LOUDSPEAKER CONTROL ONE READ THIS CAUTION RISK OF ELECTRIC SHO DO NOT OPEN CAUTION To prevent electric shock do not remove the grounding plug on the power cord or use any plug or extension cord that does not have grounding plug provided Make certain that the AC outlet is properly grounded Do not use an adapter plug with this product The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance General 1 Unpacking Check the product care fully If it has been damaged in transit report the damage immediately by calling your dealer and or the shipping company that delivered it 2 Connections Whenever changing connecting or disconnecting signal or power cables etc always turn off all equipment This prevents transients from entering the equipment and prevents electrical energy from reaching you Keep all connections out of the reach of children Before moving the unit be cer tain to disconnect any interconnection2. Speakers and electronics terminals have corresponding and terminals It is important to connect both speakers identically on the speaker to on the amplifier and on the speaker to on th amplifier Wiring out of phase results in thin sound weak bass and a poor stereo image TROUBLESHOOTING If there is no sound from any of the speakers Check that the receiver amplifier is on and a source is playing Review proper operation of your receiver amplifier If there is no sound coming from one speaker Check the Balance control on your receiver amplifier Check all wires and connec tions between receiver amplifier and speakers Make sure all wires are con nected Make sure none of the speaker wires are frayed cut or punctured If the system plays at low vol umes but shuts off as volume is increased Check all wires and connec tions between receiver amplifier and speakers Make sure all wires are con nected Make sure none of the speaker wires are frayed cut or punctured SPECIFICATIONS Drivers Bass midrange video shielded Drivers Tweeter video shielded Frequency Response Power Handling Peak Continuous Maximum Recommended Amplifier Power Sensitivity Nominal Impedance Dimensions H x W x D Weight each The maximum recommended amplifier power rating will ensure proper system headroom to allow for occasional peaks We do not rec
3. de Tours 72500 Ch teau du Loir France www jbl com 2007 Harman International Industries Incorporated SATELLITE TYPE Titanium laminate dome tweeter reflex loaded enclosure JBLis a registered trademark of JBL Incorporated PORT DESIGN FreeFlow flared Part 10030 PROFESSIONAL REFERENCE Control Monitor Series H A Harman International Company
4. non authorized person nel or accessories supplements are attached which are not approved by manufacturer importer Important Safety Precautions 16 Warranty The following items are not covered by the product warranty a Damage caused by inappropriate handling despite clear instructions provided in the owners manual b Damage to mechanical parts such as record playback heads moving rubber and plastic parts and fuses as well as results of normal wear and tear c Damage caused by external action or influence d Damage caused by miss use by user e Damage caused by excessive electrical mains supply voltage or lightning strike f Damage caused by fire water or smoke g Damage known to buyer prior to purchase h Damage caused by professional employment of home entertainment products e g for catering trade restaurants public address or infinite loop announcement use etc 17 Specifications All product specifica tions features are subject to change without notification Passive Products 18 Amplifiers Amplifiers used to drive these units must deliver a sufficient out put power A lack of output power may lead to amplifier clipping which causes damage not covered by guarantee Active Powered Products 19 Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating and these openings must no
5. cords with other components and make certain that you disconnect any powered units from the AC outlet 3 Read Instructions All the safety and operating instructions should be read before the product is operated 4 Retain Instructions The safety and operating instructions should be retained for future reference 5 Heed Warnings All warnings on the product and in the operating instructions should be adhered to 6 Follow Instructions All operating and use instructions should be followed 7 Water and Moisture The product should not be used near water for example near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool and the like 8 Accessories To ensure proper opera tion and to avoid the potential for safety hazards place the unit on a firm and level surface When placing the unit on a shelf be certain that the shelf and any mounting hardware can support the product s weight Do not place this pro duct on an unstable cart stand tripod bracket or table The product may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Any mounting of the product should follow the manu facturer s instructions and should use a mounting accessory recommended by the manufacturer 9 Wall or Ceiling Mounting The product should be m
6. l bracket hole Mount the wall bracket onto wood stud on the wall using 10 minimum 1 inch long pan head wood screws Make sure that all Q 4 screws are driven into the stud and not in drywall If the bracket needs to be mounted on drywall the use of properly selected and installed wall anchors and screws is essential Make sure that the screw head is at least 0 36 inches approximately 3 8 inches or larger in diameter so that it can properly hold the backup cord eyelet Holding the speaker cabi net with both hands reinsert the ball portion of the ball shaft into the wall bracket Hand tighten the molded nut while positioning the speaker for the intended orientation Once the orientation of the speaker is finalized use the metal bar in one of the holes on the molded nut and tighten securely Securely attach the other end of the backup cord Q to the Control ONE by engaging it through the bar on the back speaker ONE Speaker Placement O NA L As front speakers As rear speakers 1 5 1 8m oO TWO Wall mounting The Control ONE loudspeakers may be wall mounted Please refer to wall mounting instructions THREE Speaker Connections Wires Connections A Ez RIGHT of LEFT Front or Rear Channel Amplifier Receiver Outputs
7. mally or exhibits a marked change in performance 27 Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 28 Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus 29 Heat The product should be situated away from heat sources such as radia tors heat registers stoves or other prod ucts including amplifiers that produce heat Avoid installation in extremely hot or cold locations in an area that is exposed to direct sunlight or near heating equipment When positioning the product in its final location make certain that it has adequate ventilation on all sides as well as on the top and bottom CONTROL ONE Bracket assembly and mounting Important safety note Proper selection of mounting hard ware not included herein and proper assembly and installa tion of brackets including but not limited to selection of appropriate weight bearing support and bracket use with the specified speaker only is the exclusive responsibility of the cust
8. omer Manufac turer disclaims any liability for the selection of mounting hardware and or bracket installation a Loosen and remove the molded nut by turning it counter clockwise Use the supplied metal bar if necessary by inserting it in one of the holes on the molded nut Pull the ball shaft amp out of the wall bracket c Slide on the molded nut onto the ball shaft with threaded opening facing the ball and thread on the metal nut all the way onto the ball shaft with the nut 5 knurled sur face facing away from the ball d Screw on the ball shaft into the threaded insert on the back of the speaker c cabinet until it is fully seated against the bottom of the insert Tighten the knurled nut using a crescent wrench until it is firmly seated against the back of the speaker and has fully locked the ball shaft 6 and the speaker cabinet together Pleace note that once this nut is tightened it may embed some marks on the back of the speaker where the attachment is made However these marks will be covered by the nut The back up cord pro vided as an additional mea sure to prevent the fall of the speaker in case the speaker becomes detached from the wall bracket One of the two lower screws that attach the wall bracket to the wall will need to go through the eyelet at the end of the cord before going through the wal
9. omm end sustained operation at these maximum power levels Descriptions and specifications subjectto change without notice Notice to Purchaser JBL assumes no responsibility or liability for injuries or property damage direct indirect or consequential resulting from the improper installations of Control ONE loudspeakers 100mm f more than one pair of speakers is being used check the minimum impedance requirements of your receiver amplifier If there is no or low bass output Make sure the polarities 4 and of the left and right Speaker Inputs are connected properly 12mm Titanium Laminate 80Hz 20kHz 200W 50W 100W RMS 89dB 2 83V 1m 8 Ohms 228 x 155 x 139mm 2 4kg Declaration of Conformity We Harman Consumer Group Inc 2 route de Tours 72500 Chateau du Loir France declare in own responsibility that the product described in this owner s manual is in compliance with technical standards EN 61000 6 3 2001 EN 61000 6 1 2001 Laurent Rault Harman Consumer Group Inc Chateau du Loir France 08 07 OWNER S GUIDE PRODUCT LINE Control Monitor Series wwe Control One DESIGN GOAL Bring the thrill of live performance and movie sound to the home environment by calling on JBL s professional engineering leadership PRO SOUND COMES HOME JBL Consumer Products 250 Crossways Park Drive Woodbury NY 11797 Europe 2 Route
10. ot sure of the type of power supply to your home consult your prod uct dealer or local power company For products intended to operate from battery power or other sources refer to the operating instructions 21 Grounding or Polarization This product may be equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety fea ture If you are unable to insert the plug ully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug 22 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them pay ing particular attention to cords at plugs convenience receptacles and the point where they exit from the product To avoid safety hazards use only the power cord supplied with your unit If a replace ment cord is used make certain that it is of a similar gauge We do not recommend using extension cords with this product As with all electrical devices do not run power cords under rugs or carpets or place heavy objects on power cords Damaged power cords should be replaced immediately by a qualified service technician with cords meeting factory specifications When disconnect ing the power co
11. ounted on a wall or ceiling only when and as recommended by the manufacturer 10 Cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 11 Attachments Do not use attachments not recommended by the product manu facturer as they may cause hazards 12 Replacement Parts When replace ment parts are required be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 13 Safety Check Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition 14 Feet Spikes When positioning or moving this product ensure that is lifted rather than dragged across any floor mounting surface This will avoid any damage to the floor mounting sur face Attention Products and or product feet constructed of rubber or plastics may in seldom cases react chemically and discolor treated or non treated wooden surfaces if positioned without protection 15 Warranty The following conditions may result in a void product warranty a the manufacturers serial number is removed or forged b if repairs and or modifications and or other treatments tunings have been carried out by
12. rd from an AC outlet always pull the plug never pull the cord 23 Non use Periods The power cord of the product should be unplugged from the outlet when left unused for long periods of time 24 Lightning For added protection for this product during a lightning storm or when itis left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges 25 Overloading Do not overload wall outlets extension cords or integral con venience receptacles as this can result in a risk of fire or electric shock 26 Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions a The power supply cord or the plug has been damaged or b Objects have fallen or liquid has been spilled into the product or c The product has been exposed to rain or water or d The product does not operate normally when following the operating instruc tions Adjust only those controls that are covered by the operating instruc tions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation or e The product has been dropped or the enclosure damaged or f The product does not appear to operate nor
13. t be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to Make certain that the proper space more than 10cm is provided both above and below the unit for ventilation If the ampli fier will be installed in a cabinet or other enclosed area make certain that there is sufficient air movement within the cabi net with means provided for hot air to exit and for cool air to be brought in Do not obstruct the ventilation slots on the top of the unit or place objects directly over them Remember power amplifiers generate heat and the heatsink fins and ventilation slots that form part of the cabinet are specially designed to remove this heat Placing other electronic equipment near these heat dissipation systems may possibly affectthe long term reliability of both your amplifier and the objects placed above it Do not place CDs record jackets owner s manuals or other paper on top of or beneath the unit or in between prod ucts containing amplifiers in a stack This will block the air flow causing degraded performance and a possible fire hazard 20 Power Sources This product should be operated only from the type of power source indicated on the marking label If you are n
Download Pdf Manuals
Related Search