Atdec TH-WH-PJ-FM
Contents
1. assumes no responsibility for faulty installations _ de Flush Mount an Assembly x1 1 one xtension i Brackets E B a 62 Extension ae A Ea Brackets gt ee 3 Pera 100mm x2 N fee F Extension Brackets 75mm x2 Extension Brackets 150mm x2 ee WARNING Installation Instructions TELEHOOK UNIVERSAL PROJECTOR FLUSH MOUNT WARNING This bracket supports up to 15kg 33lbs DO NOT overload this bracket Bits Bag E SN Ba a M M5x10mm Z i Washer Square Nut x8 Socket Button 6mm Allen Nylon Anchor 20mm x2 Cap Screw x4 Key x1 Plug x2 10mm x4 8mm x4 G Cross Recessed Screws oa x4 3mm Allen 14 Gauge Coach Screw x2 M2 5x15 x4 Key x1 M3x15 M3x20 x4 each Spacer M4x15 M4x20 M4x25 x4 each Large x4 M5x15 M5x20 M5x25 x4 each Medium x4 M6x15 M6x20 M6x25 x4 each Small x4 e Ensure the Ceiling can support the total weight of the Projector and the Universal Flush Mount e All bolts and screws must be used at the designated points in the installation instructions to prevent damage to the projector or personal injury e DO NOT install near air conditioner vents or where there is excessive dust or smoke e Ensure the projector is mounted so that it is not possible for excessive loads to be placed on the bracket A Component Checklist Check you have received all parts against the Component Checklist above Remove the Ceiling Pla2. F Attaching the Flush Mount Assembly to the Ceiling Plate F 1 Connect the Shaft to the Ceiling Plate as shown below Ceiling Plate Insert the Locking Hook into the slot in the Ceiling Plate to lock the Flush Mount Assembly rt j m eel Locking cng nd Hook nj r 7 6mm Allen Key To make Roll Shitt adjustments first ensure the weight of the projector is supported Then loosen the M8x65mm Screw with the supplied 6mm Allen Key and adjust to your desired position Re tighten the screw firmly Installation Complete F 3 Tighten the Locking Hook with the M8x50mm Socket Cap Screw and the M8 Nyloc Nut that was previously removed Locking M8x50mm M8 Nyloc Nut Hook Socket Cap Allen Key Flush Mount and Projector Tip When the projector requires servicing remove the projector via this easy disconnection point to save time Pitch Adjustment M8xl5mm 6mm Screw Allen Key 6mm Allen Key To make Pitch adjustment first ensure the weight of the projector is supported Then loosen both M8x15mm Screws with the supplied 6mm Allen Key and adjust to your desired position Re tighten both screws firmly Due to continuing product development the manufacturer reserves the right to alter specifications without notice Published 22 03 07 IMPORTANT Please read these instructions before commencing installation as faulty installation could result in injury Atdec
3. f Gravity E 3 Place the Bottom Spacers in between the Extension Brackets and the Projector and align the mounting holes as shown below Bottom Spacers Extension Bracket Mounting Hole NOTE If your mounting holes are recessed into the projector you may need to use ale the additional Spacers supplied in the o i ieee Bits Bag Please select the appropriate E Spacer Recessed Mounting Hole Extension Bracket Spacers according to the design of your projector E 4 Select the correct Mounting Screws from the Bits Bag and firmly screw the Flush Mount Assembly onto your Projector q Once this is done the Projector Venanesee Flush Mount Assembly is ready to be mounted onto the Ceiling Plate Bottom Spacer
4. te trom the Flush Mount Assembly as shown M8x50mm Socket Cap Screw M8 Nyloc Nut Ceiling Plate Allen Key 6mm Locking Hook Installing the Ceiling Plate Choose the appropriate installation procedure depending on your ceiling type Masonry Plaster Board Wash r Masonry Ceiling Coach Screw Tighten 14 Gauge Coach Screw Finding the Center of Gravity of the Projector D 1 Centre of Gravity Pick up the projector using both of your index tingers ff Py Move your fingers along the side of the Projector follow Vi TN Step 1 until it is level Remember the balance point Fa D 2 Repeat this process for the perpendicular side follow Step 2 D 3 Where both balance points meet is the Centre of Gravity of your projector Use a pencil to mark this point E 1 Loosen the M5x10mm Screws using the supplied 3mm Allen Key until you can slide the extension 3mm brackets freely as shown quan Key You may need to replace the attached Extension Brackets with the additional longer brackets supplied in the package to suit the mounting hole configuration of your projector NOTE Ensure the screws are securely fixed into the Timber Beam Extension Bracket ike Centre of Flush Mount E 2 Place the Flush Mount Assembly over the Projector and align the centre of the Flush Mount with the Centre of Gravity marked previously on the Projector Centre o
Download Pdf Manuals
Related Search