Atdec SD-POS-VBM flat panel desk mount
Contents
1. Addendum To make any adjustments use the Tightening Tool supplied SPX f No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd a ec Due to continuing product development the manufacturer reserves the right to alter specifications without notice Published 27 07 092. SD POS VBM Installation Instructions dec Display POS Multi Component Checklist Check you have received all parts against the Component Checklist below Oe Hardware Screw Cover i Installation Template pene ONE TEE 2 5mm Allen Key x1 x1 VESA plate x1 x1 M4x12mm Screws x4 2mm Allen Key x1 E TT M4x16mm Screws x4 mD 14 Gauge Screws x4 POS Assembly x1 Top Cap x1 Tightening Tool x1 _ Security Screw x1 Pp M5 Grub Screw x1 Mounting Options Your POS Multi offers 355 of Rotation This can also be limited to suit a specitic application ee The Direction in which you hee 5 Gap in mount POS Multi will determine oN Poo ete where the 5 gap in Rotation is located and how you choose to limit the rotation Rotation Options O Rotation Fixed 0 90 Rotation O 180 Rotation 0 270 Rotation 0 355 Rotation Direction Arrow Step 1 Limit Rotation A Determine the degree of rotation you require Refer to Directo Mirrow Mounting Options above 2 5mm Allen Key B To Limit the Rotation u M5 Grub Screw 0 Locking Hole Fixed use the 2 5mm Allen Key to go insert the supplied M5 2 Base Plate 3 0 90 Locking Hole Grub Screw into your chosen Locking Hole until it p 0 180 Locking Hole sits flush with the Base Plate NOTE If you want the full i 0 270 Locking Hole 355 rotation
3. itor cables enn Run them through the Cable Management Hole down the pole and out the Cable Access Hole in the work surtace Push down firmly to attach the Top Cap Step 7 Attach the VESA plate to your Display There are two mounting hole configurations 75x 75mm e 100 x 100mm Mounting Screws x4 VESA Plate Top of Display Choose appropriate Mounting Screws from the Hardware supplied to suit your Display Back ot Display Step 8 Attach your Display to the POS Assembly _ Hook the top of the VESA plate onto Gently push the bottom of the Display Insert the Security Screw and tighten the Quickshitt Mount Tinto the Mount until you hear a CLICK using the 2mm Allen Key supplied CL Security Screw Daven Back of Display Allen Key Step 9 Adjust the VESA Ball Mount Advanced Security Installation Tension Plate Position your Display to the desired viewing angle using the 40 angular movement allowed by the VESA Ball Mount cS SS If the display does not hold its position amp or is too resistant adjust the Tension Plate lt see diagram right These Installation Instructions secure the POS Multi using the provided fasteners from above thework surtace Tightening Tool For advanced Security Installation from below the work surface Please refer to the Advanced Security Installation
4. you do NOT need to install a grub screw A Position the Installation Template in the desired location on your work surface Ensure the a Ey ie Pilot Holes straight edge sits perpendicular with the User s line of sight Mark Cener the center points of each of the 45mm 134 Cable required holes onto the work Access Hole surtace with a pencil B Drill 4 x 3mm Pilot a p Screws x4 oe Holes to a depth of 15mm 9 2 7 INSTALLATION Use a 45mm 1 hole saw to TEMPLATE drill the Cable Access Hole in the work surtace C Reposition POS Multi with the Direction Arrow pointing in L 034 Cable the direction required for your f 1s Hole chosen rotation Secure the POS jl to the work surface using the 4 x D3mm 1 9 supplied 14 Gauge Screws x4 Pilot Holes we Step 3 Attach Screw Cover Step 4 Optional Install Monitor Security Cable Security Cable NOT Included Remove the paper backing trom the Screw A Loop the Security Cable Cover and adhere to the POS base as shown Kensington or similar around the internal post of the POS Assembly B Feed the other end of the cable through the POS Assembly and out the Cable Management Hole C After you have attached the monitor As directed in Step 8 install the lock to the monitor as per the manufacturer guidelines Step 6 Install Monitor Cables Cable l Management Prior to attaching your monitor Hole install the mon
Download Pdf Manuals
Related Search