APC 66097 power distribution unit PDU
Contents
1. XR11 RAUZ card Page 26 34003602EN AB Installation connections 1 Open the doors giving access to the Switch handles 2 Carry out the UPS shut down procedure and remove the three protective panels 3 Check that the UPS is equipped with at least one GTCZ communication card ad and one RAUZ card 18 that a protected and UPS secured outlet is available 4 Configure the RAUZ and GTCZ card as indicated in section 2 6 5 Connect the power supply adapter to the UPS secured outlet 49 Bring the power supply cord Gg out through the grommet in panel A 6 Connect install then fix link cable Q3 Bring the other end of the cable out through the grommet in panel A 7 Replace the protective panels 2 Installation 8 Clean the planned location for the Galaxy view with doors open and protective panels in place external unit using the cleaning kit provided see figure 9 Remove the adhesive protection from under the external unit 10 Place the unit as shown 11 Press down hard for 10 seconds to fix the adhesive 12 Connect the power supply cord to the back of the external unit 5V DC 13 Connect the one end of the telephone cable 2 to the phone port on the external unit and the other end to the telephone lt 3m outlet If the wall outlet is not compatible with the connector on the cable use an adapter 142. Galaxy PW MGE ATTENTION Onduleur sous Teleservice UPS SYSTEMS WARNING UPS under Teleservice Ne pas mettre hors tension sans avoir au pr alable d connect la ligne t l phonique Do not switch off without first disconnecting the telephone line Pulsar Comet EXtreme Comet EX RT 2 Installation Galaxy 3000 Comet S31 34003602EN AB Page 17 2 Installation 2 6 Setting General Single unit up the RS485 link For UPSs equipped with the PowerServices TelPac external version see table section 2 3 The various installation types communication between the UPS and the external unit is achieved via a RS485 link in 2 wire mode The link works using the master slave mode with the PowerServices TelPac always being the master Standard practice is to add line bias at the network master and impedance matching at the end of the line on the slave side The line must only be biased at one point type installation The external unit is pre configured to be directly operational No special configuration is necessary for a Single unit type installation of the external unit with a Galaxy or Comet type UPS Configuration of communication parameters mode rate etc is carried out on the RS485 cards on the respective UPSs see Configuring the RS485 card for Comet or Configuring the RAUZ card for Galaxy UPS with JBUS PowerServices RS485 card Telpac
3. Master With bias Without impedance matching 1200 8 N 1 Slave number x Without bias With impedance matching 1200 8 N 1 w YA j The RS485 shielded 2 wire link Page 18 34003602EN AB Impedance matching and bias settings 2 Installation If a specific adjustment is required on the RS485 link see the settings on DIP switch SA1 Master fixed Two wire link Bias Without impedance matching Default position Switch number Function Switch number Function 1 T to R connection 5 R OV bias 2 T to R connection 6 T 5V bias 3 T OV bias 7 T T impedance matching 4 R R impedance matching 8 R 5V bias Example SA1 6 ON T has a 5V bias SA1 6 OFF T does not have a 5V bias 34003602EN AB Page 19 2 Installation Configuring the shielding terminal When electrical measurements are to be made on the RS485 link it is possible to configure the shielding terminal gt of terminal block T as a OV terminal The holes above each terminal allow a measurement probe to be inserted Default position zz SHIELDING Terminal block for the RS485 serial link to MGE UPS SYSTEMS equipment Page 20 34003602EN AB 2 Installation Configuring the RS485 card for Comet The settings proposed below comply with the recommended configuration see section Single unit type installation They must be m
4. Checking the indicator lights see section 1 5 Indicator lights Put the UPS back into operation Check the status of the green UPS indicator light 9 on steady for 5s status 1 in the table then regular flashing every second status 3 in the table Check the status of the CD indicator light ER off for 5s then regular flashing status 3 in the table PowerServices TelPac is now ready for the parameter setting stage necessary for Teleservice Consult the Technical Support documentation Lastly move on to step 2 see section 2 1 Procedure 2 10 Connecting contact type inputs PowerServices TelPac card 2 inputs Contact type inputs enable the connection of equipment without RS485 JBUS links or equipment that is unknown to PowerServices TelPac By default closing of a contact causes an alarm to be sent to the Teleservice centre The unit can also be configured to send an alarm when a contact opens The connection cable is not supplied Page 28 34003602EN AB PowerServices TelPac external unit 2 inputs 4 extensions Terminal block XM13 lt 10m Extension ops 2 Installation Four similar inputs C D E F are available inside the external unit on terminal block XM13 To connect contacts to these four inputs proceed as follows Remove the cover partly unscrew the screws and pivot the cover Remove the card from the external unit
5. ac ee ee e ee UB Te pe dee ser Doni KRE Re teer eR EO Te o ERES EA 30 Comet link cable ref 34008747 ance de tei e dn dde cena ON ka a Hc Nee 30 1 1 Unpacking and checking the contents 66096 Ko DIS 66097 66098 p 1 Presentation Content of the card version A PowerServices TelPac communication card B cover plate specifically designed for Galaxy PW UPSs C 5m telephone cable equipped with RJ11 plugs D 2 5m serial communication cable used for configuration and maintenance operations E 3 warning labels F this manual G information form needed to activate Teleservice Content of the external version A PowerServices TelPac external communication unit with its fixing kit C 5m telephone cable equipped with RJ11 plugs D 2 5m serial communication cable E 3 warning labels F this manual G information form needed to activate Teleservice H UPS link cable and fixing accessories I cleaning kit J plug in 5V DC power adapter 34003602EN AB Page 9 1 Presentation 1 2 Overview SIS ooo Page 10 34003602EN AB Power supply connector external unit Dip switch to configure the RS485 link Extension port to connect the 4 additional contact inputs Shielding configuration jump
6. residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Part 68 This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules Radio and Telecommunications compatibility The PowerServices TelPac card and external versions comply with the European R amp TTE directive on condition that they are installed and used in compliance with their intended use and manufacturer s instructions Page 4 34003602EN AB Foreword Modem compatibility and supported countries The modem integrated in the PowerServices TelPac card is compatible with European standard CTR21 01 98 in accordance with Council Decision 98 482 EC List of countries supported by the modem Australia Denmark Ireland New Zealand South Africa Austria Finland Israel Netherlands Spain Belgium France Italy Norway Sweden Brazil Germany Japan Philippines Switzerland Bulgaria Greece Korea Poland Taiwan Canada Hong Kong Luxembourg Portugal United Kingdom China Hungary Malaysia Russia United States Czechoslovakia India Mexico Singapore 34003602EN AB Page 5 Foreword Pictogram symbols Important instructions that must always be followed Information and advice Visual indication Action API UPS Uninterruptible Power System The conventions used to represent indicator lights in th
7. 3 screws Feed the cable through the grommet Connect the cable s to terminal block XM13 as shown in the figure opposite Replace the card in the external unit and fix it in place 3 screws Replace the cover PowerServices TelPac is now ready for the parameter setting stage required for Teleservice Consult the Technical Support documentation Lastly move on to step 2 see section 2 1 Procedure 34003602EN AB Page 29 3 Maintenance 3 1 Cable diagrams Serial cable ref 34003618 DB9 RJ9 cable 2 5 m DB9 female RJ9 male connector connector L Modem cable ref 34003729 RJ45 RJ11 cable 5 m Le RJ45 male RJ11 male connector connector Comet link cable ref 34003747 DB9 3 wire cable 0 9 m DB9 male connector Page 30 34003602EN AB ll 1 L2 3 4 RJ9 male DB9 female connector connector 1 2 1 3 2 4 3 5 4 6 5 7 6 L 8 RJ11 male RJ45 male connector connector 1 2 3 4 5 8 brown 8 red 9 black frame DB9 male connector
8. Connect the cable 1 to the JBUS RS485 terminal block on the card wire T on terminal T wire R on terminal R shielding 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 000000000000000000000000000 A 34003602EN AB Page 27 2 Installation
9. WWW mgeups com MGE UPS SYSTEMS M PowerServices TelPac Installation manual MGE UPS SYSTEMS THE UNINTERRUPTIBLE POWER PROVIDER ren Page 2 34003602EN AB Introduction Thank you for selecting an MGE UPS SYSTEMS product to protect your electrical equipment PowerServices TelPac has been designed with the utmost care It comes in 2 versions card ref 66096 or external ref 66097 or 66098 The card version can be installed by the customer or by an MGE UPS SYSTEMS After Sales Service technician The external version can only be installed by a specialised MGE UPS SYSTEMS After Sales Service technician We recommend you take time to read this manual to take full advantage of the many features of this product To discover the entire range of MGE UPS SYSTEMS products visit our Web site at www mgeups com or contact your nearest MGE UPS SYSTEMS representative Environment MGE UPS SYSTEMS pays great attention to the environmental impact of its products during the design and manufacture stages and through to the end of its life cycle MGE UPS SYSTEMS products comply with the strictest regulations They do not contain CFCs or HCFCs Recycling of packaging Packaging has been designed to be recycled Please make sure it is correctly recycled in compliance with applicable regulations Recycling of products at the end of their life cycle MGE UPS SYSTEMS undertakes to recycle all recovered products at the end o
10. ade before installing and commissioning the PowerServices TelPac external unit The slave number is set to 1 by default Parameters may be set using UPS Tuner or Soft Tunor 0000000 O 0000000 FA e zz qq 44 000000 0000000000 0000000 E 0c000000 0000000000 0000000 T si 2 T m 00000000000000000000 lo si arse I Dl Al O H o 0 o o 0000 0000 a oooo oooo o Kl JOJO 6761294 XM2 00000000000000000000 0000000000 0000000000 0000000000 0000000000 Configuration for Comet 34003602EN AB Page 21 2 Installation Configuring the RAUZ card for Galaxy The settings proposed below comply with the recommended configuration see section Single unit type installation They must be made before installing and commissioning the PowerServices TelPac external unit The serial link format and the slave number should be set using UPS Tuner or Soft Tunor fo TI A k DI d e H OUVERT FI RAUZ 60739856 ale ee HL h Configuration for Galaxy Also check that the XC11 jumper at the edge of the GTCZ or GT2Z card is mounted in the JBUS positio
11. e JBUS RS485 communication card A protected and UPS secured outlet 1A must be available in the vicinity of the UPS 3 Each additional UPS must be equipped with a JBUS RS485 communication card and a converter 4 The connection is made in this case via the contact type inputs 34003602EN AB Page 15 2 Installation 2 4 Recommendations To ensure continuous remote monitoring of your equipment the unit must remain permanently connected to the telephone network once installed Regular checks should be made to ensure that it is working properly via the indicator light on the front of the card or external unit see section 1 5 Indicator lights When working on your installation always disconnect the telephone line to avoid any unwanted alarms being sent to the Teleservice centre 2 5 Fitting the warning label A set of yellow warning labels is provided in the PowerServices TelPac kit This label is designed to warn MGE UPS SYSTEMS field technicians that the equipment is being remotely monitored and that work on equipment connected to PowerServices TelPac must only be performed once the telephone line has been disconnected In the case of Single unit remote monitoring one product the label is placed on this unit near the control buttons see illustration In the case of Multi unit remote monitoring several products the labels are placed near the control buttons on each product Page 16 34003602EN AB
12. e illustrations are as follows Indicator off 7 Indicator on Flashing Indicator Page 6 34003602EN AB Contents Presentation 1 4 Unpacking and checking the contents i 9 1 2 e TE 10 VES F Functions realta it 11 1 4 Technical DEET rre ceret a ite 12 1 5 Indicator lights cocoa ene tenete client cett de aa cras ta 13 Installation 2 1 d aerei aa Ee T Ce A ER UE REOR Ce AN Er eee CLR e DERE he ve CLER d 2 2 Preliminary check 2 3 The various installation types ii 2 4 EN E emere o dte ro pee rere eer eres Pipino deae ie ia 2 5 Fitting the warning label cue O RR ci LUCHA Ra guerra ge 26 Setting up the RS485 UE cc Single unit type installation Impedance matching and bias settings Configuring the shielding KC ul EE 2 7 2 8 2 9 2 10 Configuring the RS485 card for Comet Configuring the RAUZ card for Galaxy Installing the PowerServices TelPac card ii 23 Installation of the PowerServices TelPac external unit for Comet UPSs Installing the PowerServices TelPac external unit for Galaxy Ubp s 26 Connecting contact type inputs Ie eei eee det esi 28 34003602EN AB Page 7 Contents Page 8 34003602EN AB 3 Maintenance Sil 3Cable diagrams eio ios os cos Esse bone lil eene ponenti nane sno ab LIE 30 Serial cable diagrams ref 34003618 iii 30 Modem cable 34003729
13. er RS232 serial port for configuration or maintenance Card name RS485 terminal block for connection of MGE UPS SYSTEMS equipment Connection port for 2 contact inputs A and B Modem connection status indicator Indicator for data flow with the UPS s Modem connection port Modem Power input Cable entry to extension port Velcro system to attach the external unit 1 3 Functions Customer site Telpac JBUS RS485 emm A Customer site Country Teleservice PowerServices Z 1 Presentation PowerServices TelPac enables connection of one or more products to the MGE UPS SYSTEMS Teleservice centre via an analogue telephone line Several MGE UPS SYSTEMS products can be connected via a JBUS RS485 connection Connection of other equipment not supplied by MGE UPS SYSTEMS is possible via a dry contact connection The card version is designed for insertion in a UPS with a specific communication card slot The external version is designed for installation in a UPS without a specific communication card slot 34003602EN AB Page 11 1 Presentation 1 4 Technical data sheet Functions Parameters Characteristics Default values Possible values RS232 Port Rate 9600 9600 Data bits 8 8 Stop bits 1 1 Parity None Even odd RS485 Port Rate bits stop 1200 8 1 See technical support Parity None doc
14. f their life cycle in installations complying with applicable regulations Please contact our sales office Li See the environment section on our Web site at www mgeups com Special precautions If the card or external unit must be stored prior to installation always store in a dry location Storage temperature range 10 C to 70 C 34003602EN AB Page 3 Foreword EMC compatibility The PowerServices TelPac card and external versions comply with the following standards on condition that they are installed and used in compliance with their intended use and manufacturer s instructions Safety standards for IT equipment EN 60950 A11 1998 EMC EN 61000 6 2 1999 EN 61000 6 3 2002 The PowerServices TelPac card and external versions comply with the following European directives Low voltage 73 23 EEC and 93 68 EEC EMC 89 336 EEC and 93 68 EEC Federal Communication Commission FCC statement Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a
15. lPac external unit for Comet UPSs Li For this installation it is necessary to de energise the UPS The various PowerServices TelPac components do not present an electrocution hazard for the installer It is necessary to initially check That the UPS is equipped with a JBUS RS485 communication card in one of its slots situated at the back or that such a card is available for installation ref 6761294 JOJO That a UPS secured outlet is available near to the UPS L 1m as well as a telephone outlet L 4m Comet 531 7 5 10KVA Page 24 34003602EN AB Installation UPS de energised Clean the place where it is planned to fit the external unit using the solvent cleaning kit see figures Remove the protective adhesive under the external unit Place the external unit as shown according to the type of UPS Press down hard for 10 seconds to fix the adhesive Configure the JBUS RS485 card as shown in section 2 6 and place it in the recommended location Connections Connect one end of the power supply adapter cord to the back of the external unit 5V DC and the other end to a UPS secured outlet near to the UPS Connect the external unit to the JBUS RS485 communication card using the supplied cable wire T on terminal T wire R on terminal R then the shielding Connect one end of the telephone cable to the phone port on the external unit and the other end to the tele
16. n The card has a mark printed on it to identify the position Page 22 34003602EN AB 2 Installation 2 7 Installing the PowerServices TelPac card AJ laj H N B For Galaxy PW UPSs first attach the cover plate provided in the pack Installation Illustrations show the Pulsar EXtreme UPS It is not necessary to shut down the UPS Unscrew and remove the cover plate of one of the free communication card slots in the UPS Insert the card and secure it using the screws Check the indicator lights see section 1 5 Indicator lights Check the status of the UPS indicator light 40 on steady for 55 status 1 in the table then regular flashing every second during the start up phase status 3 in the table lastly random flashing during data exchange with the UPS status 4 in the table Check the status of the CD indicator light 9 offfor 5s then flashing during the start up phase status 3 in the table lastly off status 2 in the table Connection Connect the telephone cable to the card s phone port on one end and the telephone outlet on the other If the wall outlet is not compatible with the connector proposed on the cable use an adapter Installation is now complete PowerServices TelPac is operational Move on to stage 2 see section 2 1 Procedure 34003602EN AB Page 23 2 Installation 2 8 Installation of the PowerServices Te
17. one UPS is remotely monitored by PowerServices TelPac Multi unit several UPSs are remotely monitored by one single PowerServices TelPac Multiple unit installation is not dealt with in this manual It requires a special study taking into account the configurations existing on the site SUBD9 Terminal converters Ref 34003755 are available from the Logistics department LDS in order to simplify network cabling For more information please refer to the MGE UPS SYSTEMS technical support documentation Remote Installation UPS connected Version to be Other acces Authorised monitoring type to the telephone line installed sories required installer Galaxy PW Card No Customer MGE after sales Galaxy 3000 Card No Customer MGE after sales One UPS Single unit Pulsar Comet EXtreme EX RT Card No Customer MGE after sales Galaxy External unit Yes MGE after sales Comet S31 External unit Yes 2 MGE after sales Others External unit Yes MGE after sales Galaxy PW Card Yes 9 MGE after sales Several Galaxy 3000 Card Yes MGE after sales UPSs or Multi unit Pulsar Comet EXtreme EX RT Card Yes 9 MGE after sales products Galaxy External unit Yes MGE after sales Comet 531 External unit Yes MGE after sales Others External unit Yes MGE after sales 1 Galaxy must be equipped with at least one JBUS RS485 communication card with a free port COM2 2 Comet S31 must be equipped with on
18. phone outlet If the wall outlet is not compatible with the connector on the cable use an adapter Fix the cables to the back of the UPS using the attached adhesive cable holders Comet 531 15 20KVA 2 Installation Checking the indicator light see section 1 5 Indicator lights Put the UPS back into operation Check the status of the UPS green indicator light 0 5 on steady for 5s status 1 in the table then regular flashing every second status 3 in the table Check the status of CD indicator light 9 off for 5s then regular flashing status 3 in the table PowerServices TelPac is now ready for the parameter setting stage that is necessary for Teleservice Consult the Technical Support documentation Lastly proceed to step 2 see section 2 1 Procedure 34003602EN AB Page 25 2 Installation 2 9 Installing the PowerServices TelPac external unit for Galaxy UPSs Installation must be carried out by our technicians Installation of the PowerServices TelPac external unit requires UPS shut down load tranfer to bypass and removal of three protective panels Refer to the UPS s user manual to carry out shut down procedures in full compliance with safety procedures and instructions Non compliance with these may lead to safety hazards for the people concerned Galaxy view with doors open and protective panels removed amp C
19. umentation Mode 2 wires 2 wires 4 wires Master slave Master Master Bias With With without Impedance matching Without With without Cable cross section 0 08 0 6 mm 28 20 AWG Modem Analogue V 34 33 6 kbps Error correction V 42 LAPM and MNP 2 4 Data compression V 42b and MNP5 Country Works with 39 country profiles Protection European CTR21 compatibility Line protection included Contact inputs Dry contacts Normally open NO NO NC 0 08 0 6 mm 28 20 AWG Number 2 card version 0to2 2 4 external version 0 08 0 5 mm 28 20 AWG 0 to 6 Distance 10m maximum Power supply Voltage 5V DC external version Current MA Comment only MGE UPS SYSTEMS can be connected to the RS485 link Page 12 34003602EN AB 1 5 Indicator lights 1 Presentation Status Green UPS indicator Card version External version xl A PA 1 0 Self tests UPS communication fault P d N 2 O Card fault Card fault K Pu 1 sec 3 po Waiting for UPS communication Waiting for UPS communication 4 cmm m m Exchanging data with UPS Exchanging data with UPS Status Red CD indicator 9 Card version External version x PA 1 i Modem connected Modem connected Modem not connected Modem not connected 2 O Communication
20. with all remotely Communication with all remotely monitored UPSs OK monitored UPSs OK S soi 1 sec Communication with at least one of Communication with at least one of Pu a N amp the remotely monitored UPSs NOK the remotely monitored UPSs NOK 4 lt A i E IX NNNRENERENENEN Modem connecting Modem connecting 1 When status 3 and 4 are present at the same time status 4 is indicated 34003602EN AB Page 13 2 Installation 2 1 Procedure 1 Install the PowerServices TelPac kit using the present manual 2 Fill in the information form 3 Send the form to your Teleservice centre by Fax or Internet 4 Your centre will activate this service 5 You receive an acknowledgement of receipt The information form must be sent back in order to trigger remote monitoring of your equipment 2 2 Preliminary check Before starting the installation Make sure that an analogue type telephone outlet with an RJ11 jack is available in the vicinity of the UPS If the telephone outlet is not RJ11 type use an adapter The telephone line must be authorised to call the Teleservice centre 7 days a week If no electrical outlet is available on the UPS on which the PowerServices TelPac is to be installed connect the power cord to an outlet protected by the UPS Page 14 34003602EN AB 2 Installation 2 3 The various installation types a There are two types of installation Single unit only
Download Pdf Manuals
Related Search