CyberPower CPS1500AVR uninterruptible power supply (UPS)
Contents
1. Serial Port Serial Port Il PRIMARY Secondary Primary Computer Secondary Computer Install PowerPanel Plus Install PowerPanel Use of the software is optional The UPS will provide battery backup and surge protection without using the software The software is required for the automatic shutdown feature 3 CyberPower The Primary computer with PowerPanel Plus installed is the computer that you will use to control the UPS and make any changes to the operation of the UPS The Secondary computer with PowerPanel installed is unable to exhibit any control over the UPS When there is a power failure the Primary computer will start to shutdown after a user controlled delay Once the Primary computer is shutdown the UPS will signal the secondary computer and initiate a shutdown The secondary computer will then shutdown Once the secondary computer has completed its shutdown the UPS will power off Both PowerPanel Plus and PowerPanel will save and close any open files prior to shutting the system down If you are using the UPS to control only one computer connect a serial cable to Serial Port and your computer You will not need to use the second serial cable POWERPANEL PLUS SOFTWARE INSTALLATION GUIDE Note Use of the software is optional The unit will provide surge suppression and battery backup without using the software PowerPanel Plus should be used on the primary computer FOR WINDOWS 952. The Tower Controls the Power User Manual for CPS1500AVR UPS and PowerPanel Plus Software ADDITIONAL INSTALLATION TIPS CAN BE FOUND AT www cyberpowersystems com 1500FAQs htm CyberPower TABLE OF CONTENTS Description O O Determining Power Requirements _ 2 sia 3 4 Hardware Installation Guide Software Information PowerPanel Plus Installation PowerPanel Plus User Guide 6 PowerPanel Installation 9 Battery Replacement Instructions g LED Indicators 10 Troubleshooting Guide 11 Specifications 11 Warranty 12 Thank you for purchasing a CyberPower Systems product To enjoy all the features and benefits of this Uninterruptible Power System UPS please read and follow all installation and operation instructions completely This UPS is designed to provide guaranteed power protection for connected electronic equipment The included PowerPanel Plus software saves data closes open applications and automatically shuts down your computer system in an intelligent and orderly manner IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important safety instructions Please read and follow all instructions carefully during installation and operation of the unit Read this manual thoroughly before attempting to unpack install or operate CAUTION To prevent the risk of fire or electric shock install in a temperature and humidity controlled indoor area fr
3. 1 PowerPanel Software Disk 2 Serial Interface Cable DB 9 1 Telephone Cable 1 User Manual 1 Warranty Registration Card 1 UPS Unit 2 Rack mount Brackets 2 Stands HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT i 2 Make sure that the total Volt Amp VA requirements of your computer monitor and peripheral equipment does not exceed 1500VA 950 Watts lf the power requirements of your equipment are listed in units other than Volt Amps VA convert Watts W or Amps A into VA by doing the calculations below Note The below equation only calculates the maximum amount of VA that the equipment can use not what is typically used by the equipment at one time Users should expect usage requirements to be approximately 80 of below value to estimate power requirements ______ Watts W x 1 60 _ VAor Amps A x 125 VA Add the totals up for all pieces of equipment and multiply this total by 0 8 to calculate the actual power requirements There are many factors that can effect the amount of power that your computer system will require The total load that you will be placing on the battery powered outlets should not exceed 80 of the unit s capacity HARDWARE INSTALLATION GUIDE 8a 1 Your new UPS may be used immediately upon receipt However recharging the battery for at least four hours is recommended eS hy W to insure that the battery s maximum charge capacity is achieved aR B
4. ODNO When your computer restarts the PowerPanel software will appear on your screen for a few seconds and then minimize It will appear as a blue and white battery icon located in the system tray near the clock PowerPanel Icon Pr start Icea TFQ 0 oam FOR WINDOWS NT Click on Start point to Settings then click Control Panel Double click the UPS Icon Remove the checkmark from the box labeled UPS is installed on Click OK Acknowledge the message that the UPS is in an unknown state and exit to the desktop Shutdown your computer Turn off the UPS and unplug it Connect the serial cable to Serial Port II on the UPS and on open serial port on your computer You must use the serial cable that was provided with the unit 8 Plug the UPS into an AC outlet turn the UPS on and then start your computer Click on Start point to Settings then click Control Panel 10 Double click on Add Remove Programs 11 Click the Install Button and follow the on screen instructions 12 When the installation is complete remove the floppy disk and restart your computer Se SN When your computer restarts the PowerPanel software will appear on your screen for a few seconds and then minimize It will appear as a blue and white battery icon located in the system tray near the clock PowerPanel Icon CPS1500AVR Guaranteed Uninterruptible Power System FOR WINDOWS 2000 1 Click on Start point to Settings then click Control Panel 2
5. 56AM AA Start E B FOR WINDOWS NT Click on Start point to Settings and then click Control Panel Double click on the UPS icon Remove the check mark from the box labeled UPS is Installed On Click OK Acknowledge the message that the UPS service is in an unknown state Exit to the desktop Shutdown the computer Turn off the UPS and unplug it ee he E CyberPower Connect the serial interface cable to the UPS and an open serial port on the back of the computer You must use the serial cable that was provided with the unit 10 Plug the UPS into and AC outlet turn the UPS on and start your computer 11 Click on Start point to Settings and then click Control Panel 12 Double click on Add Remove Programs 13 Insert the PowerPanel Plus Primary disk into the floppy drive 14 Click Install 15 Follow the on screen instructions 16 Once the software is finished installing remove the floppy disk and restart your computer When your computer restarts the PowerPanel Plus software will appear on your screen for a few seconds and then minimize It will appear as a blue and white battery icon located in the system tray near the clock i PowerPanel Plus Icon Ea EFTE 11 56 AM Asear E B p a gt POWERPANEL PLUS SOFTWARE USER MANUAL PowerPanel Plus version 1 13 or greater is designed for use with Windows 95 98 Me NT and Windows 2000 For Windows XP use version 1 17 or greater The late
6. 98 Me 1 Turn the UPS off and unplug it 2 Connect the serial interface cable to the primary serial port on the UPS and an open serial port on the computer You must use the serial cable that was provided with the unit Plug the UPS into an AC outlet turn the UPS on and start the computer Windows will find New Hardware Insert the PowerPanel Plus Primary disk into the floppy drive Follow the on screen instructions Once the software has finished installing remove the floppy disk and restart your computer NO Ol AR When the computer restarts the PowerPanel Plus software will appear on your screen for a few seconds and then minimize It will appear as a blue and white battery icon located in the system tray near the clock PowerPanel Plus Icon Asur COTA gt SUSLZSO 5AM FOR WINDOWS XP Home and Professional Click on Start and then click on Control Panel Double click on Power Options then click on the UPS tab Set the manufacturer to none Exit to the desktop and shutdown your computer Turn the UPS off and unplug it Connect the serial cable to the UPS and an open serial port on the computer You must use the serial cable that came with the unit Plug the UPS into an AC outlet turn the UPS on and start your computer 4 OooarkWwWN N CPS1500AVR Guaranteed Uninterruptible Power System 8 Windows will find new hardware 9 Insert the PowerPanel Plus Primary d
7. Charge loss may occur during shipping and storage To recharge the battery simply leave the unit plugged into anAC outlet The TECT j unit will charge in either the on or off position j If you wish to use the software connect the enclosed serial ami interface cable to the serial port on the UPS and an open serial iea port on the computer Use of the software is optional If you are mo not going to use the software you do not need to connect the cable i With the UPS unit off and unplugged connect your computer Unplug Wh monitor and any externally powered data storage device Tape gt i i drive Zip Drive etc into the battery powered outlets Items D y IA ie such as copiers laser printers vacuums space heaters or other large electrical devices should not be connected to the UPS The power demands of these devices will overload j and possibly damage the UPS y To protect your modem phone or fax connect a phone cable k to the phone jack on the wall and the IN port on the UPS F Connect another phone cable to the OUT port on the UPS and your phone fax or modem device CPS1500AVR Guaranteed Uninterruptible Power System 5 Plug the UPS into a 2 pole 3 wire grounding receptacle wall outlet Make sure that the outlet is protected by a rq fuse or circuit breaker and does not service equipment a with large electrical loads i e copier refrigerator etc Ob Avoid using extension cords
8. If used the extension cord la must be rated for at least 15 Amps 6 Depress the power switch to turn the unit on The power indicator light will illuminate 7 lf an overload is detected an audible alarm will sound and the unit will emit one long beep To correct this turn the UPS off unplug at least one piece of equipment wait 10 seconds check to make sure that the circuit breakers are depressed and turn the unit on 8 Your UPS is equipped with an auto charge feature When the UPS is plugged into an AC outlet the battery will automatically recharge 9 To maintain optimal battery charge leave the UPS plugged in at all times 10 To store your UPS for an extended period of time cover it and store with the battery fully charged Recharge the battery every 3 months to prolong battery life SOFTWARE INSTALLATION INFORMATION The CPS1500AVR comes with two built in serial ports that allow two computers to be shutdown by the UPS The serial ports are labeled Serial Port PRIMARY and Serial Port Il Serial Port is for the primary computer The computer that is connected to this port need to have PowerPanel Plus installed The second computer should be connected to Serial Port Il This computer should have PowerPanel software installed Please refer to the following diagram for more information Additional information about setting up two computers can be found on our website at www cyberpowersystems com 1500FAQs htm
9. claim for warranty service 3 When you contact CyberPower identify the Product the Purchase Date and the item s of Connected Equipment Have information on all applicable insurance or other resources of recovery payment that are available to the Initial Customer and the name of the power utility supplier for the location of the connected equipment and Request a Return Materials Authorization RMA 4 Pack and ship the product to CyberPower and if requested the item s of Connected Equipment a repair cost estimate for the for the damage to the Connected Equipment and all claim forms that CyberPower provides to you Show the RMA number on the shipping label or include it with the product Initial Customer shall prepay all shipping costs and is responsible for packaging and shipment CyberPower will inspect and examine the Product and the item s of Connected Equipment or at CyberPower s election your written statement and repair cost estimate for those item s You must return the product for inspection If the Product is warranted under the Limited Warranty and the damage to Connected Equipment is covered by the Power Control Guarantee CyberPower will in addition to Limited Warranty remedies for the CyberPower Product itself repair or pay the costs of repair or replace the Connected Equipment or at the option of CyberPower as permitted by law pay to the Initial Customer the Agreed Damage Amount up to the aggregate limits stated belo
10. damaged by AC power line transients spikes or surges on properly installed grounded and code compliant 120 volt power lines in the United States and Canada or by transients surges or spikes on standard telephone equipment lines or Base 10 100T Ethernet lines that are properly installed and connected a Power Disturbance and y is directly plugged into and properly connected to a CyberPower Product in its original condition which is properly operated when a Power Disturbance passes through the CyberPower Product and y 1 exhausts the protection capacity of the CyberPower Product or y 2 damages the CyberPower Product This provision sets out the only liability of any character of CyberPower for direct indirect special consequential and or incidental damages under our Limited Warranty applies only to Connected Equipment and all such Liability is limited to the Agreed Damage Amount To make a Warranty claim for damage to Connected Equipment under the Power Control Guarantee you must do the following 1 Have completed and returned the CyberPower Warranty card or provide reasonable proof of purchase for example a sales receipt that establishes you as the original end user consumer purchaser of the product 2 Call CyberPower at 952 403 9500 write to CyberPower at 5555 12th Ave East Suite 110 Shakopee MN 55379 or e mail CyberPower at tech cyberpowersystems com within ten 10 days of the date of the event for which you wish to make a
11. displays the internal operating temperature of the unit 9 Load Level This indicator shows the of capacity of the battery outlets that is currently being used This indicator appears in green or gray but will turn red if the load exceeds 90 10 Output Voltage This indicator shows the output voltage of the UPS POWERPANEL PLUS SETUP WINDOW 1 Sensitive to variation on Line Voltage This feature is for other CyberPower Products The 1500AVR has Automatic Voltage regulation so this is not needed 2 Auto Restart This feature restores power to the outlets when AC power returns 3 Software Broadcast When enabled the software will play audible voice prompts through your computer speakers 4 Time Between Power Failure and Shutdown This is the user controllable delay between when the power fails and the software starts the shutdown process If unchecked the UPS will run until the low battery signal is received 2 minutes of backup time remaining and then start the shutdown process 5 Time Between Power Failure and Initial Warning This setting determines the delay between when the power fails and the first audible alarm LO gf Seneitree to varation on lie vo tage E Auto Restart M Time between power fiba and shutdown Time between power failure and miiial warning EE eC Delay between warming neseages CyberPower 6 Delay between warning messages User adjustable setting
12. for connected Press this switch to run a self test equipment and insures temporary 3 Battery Capacity Load Indicator uninterrupted operation of connected These indicators show a visual equipment during a power failure indication of the battery charge as well 10 Two Serial Ports as the unit s load Two ports allow connection and 4 Power On Indicator communication between the UPS This LED is illuminated when the utility and two computers This allows the condition is normal and the UPS simultaneous shutdown of two outlets are providing power free of computer systems Surges and spikes 11 Communication Protection Ports 5 AVR Indicator Ports protect standard modem fax This indicator is illuminated when the telephone line or network cable unit s AVR feature is engaged 12 10 Power Cord 6 Using Battery Indicator Heavy duty long reach power cord This indicator is illuminated when the allows you to put power where you unit is providing battery power need it 7 Wiring Fault Indicator 13 Resettable Circuit Breakers This LED will illuminate to warn the Resettable circuit breakers provide user that a wiring problem exists optimal overload protection within the AC receptacle such as a bad ground miss ground or reversed wiring If illuminated disconnect all equipment and contact an electrician to insure outlet is properly wired CyberPower INSPECTION The box should contain the following 1 PowerPanel Plus Software Disk
13. AC outlet turn the UPS on and start the computer Once the computer was finished booting insert the PowerPanel disk into the floppy drive Click on Start point to Settings and then click Control Panel Double click on Add Remove Programs Click the Install Button Follow the on screen instructions Once the installation is finished remove the floppy disk and restart your computer N Se ee When your computer restarts the PowerPanel software will appear on your screen for a few seconds and then minimize It will appear as a blue and white battery icon located in the system tray near the clock PowerPanel Icon CyberPower FOR WINDOWS XP Home and Professional Click on Start then click on Control Panel Double click on Power Options then click the UPS tab set the manufacturer to None Exit to the desktop and then shutdown your computer Connect the serial cable to Serial Port Il on the UPS and an open serial port on your computer You must use the serial cable that was provided with the unit Plug the UPS into an AC outlet turn the UPS on and then start your computer Insert the PowerPanel disk into the floppy drive Click on Start then click Control Panel Double click on Add or Remove Programs 10 Click on Add New Programs then click the CD or Floppy Button 11 Follow the on screen instructions 12 When the installation is complete remove the floppy disk and restart your computer Oe a a
14. DITIONS COMMON TO THE LIMITED WARRANTY AND THE POWER CONTROL GUARANTEE The Limited Warranty and the Power Control Guarantee are the only and the exclusive express warranty of CyberPower with respect to the Product This exclusion of other express warranties applies to written and oral express warranties Any Implied Warranty of Merchantability or for Fitness for a Particular Purpose if applicable to the Product is limited in duration to the period of ownership by the Initial Customer This provision shall NOT create any Implied Warranty or Merchantability or of Fitness for a Particular Purpose that would not otherwise apply to the Product NOTE Some States do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you LIMITATION THE LIMITED WARRANTY AND THE POWER CONTROL GUARANTEE DO NOT COVER The Limited Warranty and the Power Control Guarantee are intended to exclusive rights and remedies and replace any other rights to the extent allowed by law 1 As to CyberPower products the limited warranty does not cover or apply to misuse modification operation or storage outside environmental limits for the Products in transit in shipment or in storage damage or deterioration improper operation or maintenance or use with items or equipment not designed or intended for use with the product 2 As to Connected Equipment the Power Control Guarantee covers only damage within the specific terms of th
15. Double click on Power Options 3 On the UPS Tab click Select 4 Inthe UPS selection dialog box under Manufacturers select None 5 Exit to the desktop 6 Shutdown the computer then turn the UPS off and unplug it 7 Connect the serial cable to Serial Port Il on the UPS and an open serial port on the computer You must use the serial cable that was provided with the unit 8 Plug the UPS into an AC outlet turn the UPS on and then start your computer 9 Insert the PowerPanel software disk into the floppy drive 10 Click on Start point to Settings and then click Control Panel 11 Double click on Add Remove Programs 12 Click the Install Button 13 Follow the on screen instructions 14 When the installation is complete remove the floppy disk and restart your computer When your computer restarts the PowerPanel software will appear on your screen for a few seconds and then minimize It will appear as a blue and white battery icon located in the system tray near the clock PowerPanel Icon TESTING YOUR UPS SYSTEM Once you have set up your UPS system you may wish to test it Make sure that the UPS has been charged for at least 4 hours before testing To test the UPS simply depress the test button located on the front of the unit The unit will cycle to battery and emit an audible beep The unit will stop beeping when the test is complete You may also use the self test function in the PowerPanel Plus soft
16. ES CyberPower does not sell the Products for use in high risk activities The Product is not designed or intended for use in hazardous environments requiring fail safe performance including the operation of nuclear facilities aircraft navigation or communication systems air traffic control weapons systems life support or medical applications or for use in any circumstance in which the failure of the Product could lead directly to death personal injury or severe physical or property damage or that would affect operation or safety of any medical or life support device collectively High Risk Activities CyberPower expressly disclaims any express or implied warranty of fitness for High Risk Activities CyberPower does not authorize use of any of its products use in any High Risk Activities ANY SUCH USE IS IMPROPER AND IS AMISUSE OF CYBERPOWER PRODUCTS The Limited Warranty and the Power Control Guarantee are governed by the laws of the United States and the State of Minnesota without reference to conflict of law principles The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded Contact Information CyberPower s address is 5555 12th Ave East Suite 110 Shakopee MN 55379 and its phone number is 952 403 9500 CyberPower is the warrantor under this Limited Warranty You may also contact CyberPower on the Internet at www cyberpowersystems com 17 FCC Notice This equipment h
17. antee are subject to the terms set forth below Additionally State or Provincial law may adjust the terms of the Limited Warranty or the Power Control Guarantee or the State or Province may impose additional obligations or additional implied warranties To the extent necessary to comply with those laws the terms of the Limited Warranty and the Power Control Guarantee should be read to adjust to those requirements only to the extent necessary to comply with such local law If you are an Initial Customer you are asked to read the following terms and conditions carefully before using the Product By using the Product you consent to be bound by and become a party to the Limited Warranty and Power Control Guarantee If you do not agree to the terms and conditions of the Limited Warranty and Power Control Guarantee you should return the Product for a full refund prior to using it REGISTRATION CyberPower requests that you complete and return the Warranty Registration Card enclosed with the Product or register the Product at its website www cyberpowersystems com to establish that you are the original end user consumer purchaser of the Product and therefore entitled coverage under the Limited Warranty and the Power Control Guarantee Registration is not required for Limited Warranty coverage but note if you do not complete a registration card you will be required to provide proof of purchase as described below to have the benefits of this Limited Warrant
18. as been tested and found to comply with the limits for a Class B Digital Device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the i nterference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for help Any special accessories needed for compliance must be specified in the instruction CAUTION A shielded type power cord is required in order to meet FCC e mission limits and also to prevent interference to the nearby radio and television reception It is essential that only the supplied power cord be used Use only shielded cables to connect I O devices to this equipment CAUTION Any changes or modific ations not exp
19. d on the day of the week POWERPANEL PLUS LOG MENU z i 1 Event Option Button When selected the log will display different events suchas 1 z foe Facts m 1 O Event Closed Application Information Data Record 5 power failure program start and program end 2 Log Display Displays information as ee eee selected by the Event Closed Application 27i 2001 10 29 09 20 33 Shutdown Process begin 3 Information or Data Record option button a che leider tigi 7 A001 10 29 09 25 21 Shutdown Process besim 3 Clear Clears the selected log 2001 10 29 09 25 48 shutdown Process end 4 Cancel Exits the screen without saving 2001 10 29 09 25 48 Power Panel Plus end 200 11029 09 28 44 Power Panel Phe start any changes 2001 10 29 09 28 45 Power Panel Flus end 5 OK Exits the screen and saves changes 6 Data Record Option Button When selected the log will display a record of items that are shown in the main window such as input output voltage and temperature 7 Closed Application information Option Button When selected the log will display the names and locations of any files that were auto saved by the software POWERPANEL INSTALLATION GUIDE FOR WINDOWS 95 98 ME Turn the UPS off and unplug it Connect the serial interface cable to Serial Port Il on the UPS and an open serial port on your computer You must use the serial cable that was provided with the unit Plug the UPS into and
20. dard telephone land lines PBX telephone equipment lines or Base 10T Ethernet lines when properly installed and connected This exclusion applies for example to fluctuations in data transmission or reception by CATV or Therefore transmission or fluctuations or by transients in such transmission 3 Damage from any circumstance described as excluded above with respect to the product 4 Damages from fire flood wind rain rising water leakage or breakage of plumbing abuse misuse or alteration of either the product or the Connected Equipment Exclusion of Consequential and Other Damages The sole and exclusive remedies of the Initial Customer are those provided by the Limited Warranty and Power Control Guarantee CyberPower excludes any liability for personal injury under the Limited Warranty and Power Control Guarantee CyberPower excludes any liability for direct indirect special incidental or consequential damages whether for damage to or loss of property loss of profits business interruption loss of information or data EXCEPT FOR AND ONLY FOR the specific limited agreement of CYBERPOWER to provide certain warranty benefits regarding Connected Equipment under the CYBERPOWER Power Control Guarantee NOTE Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT OR OTHER HIGH RISK ACTIVITI
21. e whether or not the Initial Customer makes a claim for recovery including but not limited to a claim under any applicable insurance other warranty or extended warranty The Power Control Guarantee is separate from the Limited Warranty but they are related The Limited Warranty does not cover Connected Equipment but as is explained below to be covered under the Power Control Guarantee the Connected Equipment must have been damaged due to a failure of the Product that is covered by the Limited Warranty The Connected Equipment must have been damaged due to a defect in materials or workmanship of the Product and the Product must still be covered by the Limited Warranty and the Initial Customer has made a valid claim for the Product under the Limited Warranty In the event of damage to the Connected Equipment your exclusive remedy and CyberPower s sole obligations are as follows for Connected Equipment If a the Product purchased and owned by you is defective in material or workmanship under the Limited Warranty or any applicable Implied Warranty b the Limited Warranty requirements have been met and c none of the limitations or exclusions on warranty coverage apply CyberPower will as CyberPower elects as permitted by law repair replace or pay the Agreed Damage Amount defined below for the item s of your electronic equipment directly and properly connected to the product the Connected Equipment if that Connected Equipment is x
22. e Power Control Guarantee to Connected Equipment and only up to the applicable aggregate ceiling amount The Power Control Guarantee does not cover damage to Connected Equipment or apply if the product has been operated in a failure mode or not in compliance with CyberPower operating instructions and manuals or if the Connected Equipment has been operated in a failure mode or not in compliance with the instructions and manuals of its manufacturer vendor The Limited Warranty and the Power Control Guarantee Do Not Apply Unless The Initial Customer 1 Has properly connected the Product and the Connected Equipment to properly wired and grounded outlets including compliance with electrical and safety codes of the most current electrical code ANS NFPA 70 without the use of any adapters extension cords of other connectors 2 Has provided a suitable and proper environment for use and installation of the Product and Connected Equipment 3 Has properly installed and operated the CyberPower Product and Connected equipment CyberPower Does Not Cover or Undertake Any Liability in Any Event for Any of the Following 1 Loss of or damage to data records or software or the restoration of data or records or the reinstallation of software 2 Damage from causes other than AC Power Line Transients spikes or surges on properly installed grounded and code compliant 120 volt power lines in the United States and Canada transients surges or spikes on stan
23. ed Uninterruptible Power System POWERPANEL PLUS MAIN WINDOW DESCRIPTION 1 Input Voltage This reading shows the 2 current input voltage of the utility power The input normally displays in green but will i ee appear in red if the input voltage is lower than 85v of higher than 150v 2 Battery Level This indicator displays the current charge on the battery The 3 H indicator will turn red during a power failure 3 Frequency This indicator displays the frequency of the utility power 4 Scheduled On PowerPanel Plus can be scheduled to turn your computer system on This indicator displays Scheduled on settings that will occur in the next seven 4 days 5 Final Countdown When PowerPanel Plus detects that the utility voltage is below 85v or above 150v the final countdown will begin When the countdown reaches zero PowerPanel Plus will save and close any open files and then shut down the system in an intelligent and orderly manner 6 Approximate Backup Time This indicator shows the approximate amount of backup time that is available based upon the battery capacity and the load on the system This indicator can appear in red yellow or green depending upon the number of minutes available 7 Scheduled Off PowerPanel Plus can be set to automatically shutdown the computer at a user specified time Scheduled Off settings that are set to occur within seven days are displayed 8 Temperature This indicator
24. ee of conductive contaminants Please see specifications for acceptable temperature and humidity range CAUTION To reduce the risk of electric shock do not remove the cover except to service the battery No user serviceable parts inside except for the battery CAUTION Hazardous live parts inside can be energized by the battery even when AC input power is disconnected CAUTION UPS must be connected to an AC outlet with fuse or circuit breaker protection DO NOT plug unit into an outlet that is not grounded CAUTION To avoid electrical shock turn off the unit and unplug it from the AC power source BEFORE servicing the battery or installing a computer component DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT CyberPower Systems does not sell products for life Support or medical applications DO NOT use in any circumstance that would affect operation or safety of any life Support equipment with any medical applications or patient care Z DO NOT USE WITH OR NEAR AQUARIUMS To reduce the risk of fire or electric shock do not use with or near an aquarium Condensation from the aquarium can cause the unit to short out CPS1500AVR Guaranteed Uninterruptible Power System DESCRIPTION o j 1 Power Switch 9 Battery Backup Surge Protection Can be used as a master on off switch and AVR Outlets for equipment connected to the UPS Provides six battery powered surge 2 Test Switch protected AVR outlets
25. ff and unplug at least one piece of equipment Wait 5 seconds reset the circuit breakers and restart the UPS Off Off Off Off Set Off Surge Protection Malfunction Power surge has damaged the unit Please contact CyberPower Systems On Off On Off On Off Flash On Off Set Up None Electrical Wiring Fault Indicates a wiring problem such as a bad ground missed ground or reversed wiring within the AC outlet User is advised to disconnect all equipment from the outlet and have it checked by an electrician BO oon E 20 100 ARE Su ed i r peun 60 80 60 80 40 60 on 40 60 20 40 20 40 BATT WE e LOAD The load indicator LED will turn red if the load is between 80 and 100 If the load or battery charge is under 20 no indicator LED will illuminate 13 CyberPower TROUBLESHOOTING Problem Possible Cause Solution Outlets do not provide Circuit breaker is tripped due Turn the UPS off and unplug at least one power to equipment to overload piece of equipment Wait 10 seconds reset the circuit breaker and then turn the UPS on Batteries are discharged Allow the unit to recharge for at least 4 hours Unit has been damaged by a Contact CyberPower Systems at surge or spike tech cyberpowersystems com The UPS does not Batteries are not fully charged Recharge the battery by leaving the UPS perform expected runtime plugged in Batter
26. for the delay between the audible alarms that occur during a power failure 7 UPS Self test Allows the user to test the UPS without having to unplug the unit from the wall When the run button is clicked the unit will switch to battery power and the unit will beep 8 About This button will display information about the software as well as contact information 9 Advance This button opens the Advanced Setup Window 10 Default Click this button to return the software to the original factory settings 11 Cancel This button exits the window without saving changes 12 OK This button exits the windows and saves any changes 13 UPS Installed On Shows the port that the UPS is using The port assigned to the UPS needs to be used exclusively by the PowerPanel Plus software 14 Buzzer This toggles the audible alarm on and off POWERPANEL PLUS ADVANCED SETUP 1 Low Battery Voltage This sets the low battery cutoff level The user can slightly extend the UPS run time by adjusting this 4 TE T TI Remote On FaxOn setting ct Volam Faha H Password j 2 High Voltage Failure Sets the upper 9__ ES Ring E level where the UPS will cycle to battery ee a E min 3 Low Voltage Failure Sets the lower 3 oe eee level where the UPS will cycle to battery a i 4 Battery mode Output Voltage Sets the _ _ M Ta cots sae voltage that the UPS will output when running on battery This level can be adjusted f
27. ies are worn out Contact CyberPower Systems at tech cyberpowersystems com The UPS will not turn on The on off switch is designed to Turn the UPS off Wait 10 seconds and then prevent damage by rapidly turn the UPS on turning it off and on The unit is not connected to an The unit must be connected to a 110 120v outlet AC outlet The batteries are worn out Contact CyberPower Systems at tech cyberpowersystems com Mechanical problem Contact CyberPower Systems at tech cyberpowersystems com PowerPanel Plus is inactive all icons are gray open serial port on the back of the computer The serial cable is not connected Connect the serial cable to the UPS unit and an You must use the cable that came with the unit The serial cable is connected to The primary computer must be connected to the wrong port Port on the UPS Check the back of the computer for a different serial port Move the cable to this port The unit is not providing battery Turn the UPS off Wait 10 seconds and then power turn the UPS on This should reset the unit The serial cable is not the cable You must use the cable that came with the unit that was provided with the unit SPECIFICATIONS Battery while input voltage is from 8 to 30 under nominal while input voltage is from 8 to 26 over nominal 120 Vac 5 user adjustable Power On Electrical Wiring Fault AVR Using Battery Battery Charge Leve
28. isk into the floppy drive 10 Follow the on screen instructions 11 Once the software has finished installing remove the floppy disk and restart your computer When your computer restarts the PowerPanel Plus software will appear on your screen for a few seconds and then minimize It will appear as a blue and white battery icon located in the system tray near the clock PowerPanel Plus Icon l FOR WINDOWS 2000 Click on Start point to Settings then click Control Panel Double click on Power Options On the UPS tab click Select In the UPS selection dialog box under Manufacturers select none Exit to the desktop Shutdown the computer Turn the UPS off and unplug it Connect the serial interface cable to the UPS and an open serial port on the back of your computer You must use the serail cable that was provided with the unit 9 Plug the UPS into an AC outlet turn the UPS on and start your computer 10 Windows will find new hardware 11 Insert the PowerPanel Plus Primary disk into the floppy drive 12 Follow the on screen instructions 13 Once the software has finished installing remove the floppy disk and restart your computer oe a a When your computer restarts the PowerPanel Plus software will appear on your screen for a few seconds and then minimize It will appear as a blue and white battery icon located in the system tray near the clock PowerPanel Plus Icon Zoe SEBLSE 11
29. l Load Level Ouput Receptacles 6 Battery powered and full time surge protection 14 CPS1500AVR Guaranteed Uninterruptible Power System Limited Warranty And Power Control Guarantee In purchasing a CPS1500AVR in the United States or Canada the original end user receives a Limited Warranty and CyberPower s Power Control Guarantee from CyberPower Systems USA Inc for ease of reading referred to as CyberPower The Limited Warranty and the Power Control Guarantee are intended to be the initial end user s exclusive rights and remedies The Limited Warranty and the Power Control Guarantee are separate all though they are related Limited Warranty The original end user referred to as the Initial Customer receives an express limited warranty for the CPS1500AVR referred to as the Limited Warranty purchased from CyberPower referred to as the Product The Limited Warranty is for the Product itself The terms of the Limited Warranty are explained below Power Control Guarantee CyberPower also provides the Initial Customer with protection in the event that the Product is not free from defects in materials and workmanship and certain equipment connected to the Product is damaged the Power Control Guarantee The Power Control Guarantee protects the Initial Customer for damage to equipment plugged into the Product The terms of the Power Control Guarantee are explained below The Limited Warranty and the Power Control Guar
30. reduced if such grounds are removed during installation and maintenance applicable to a UPS and a remote battery supply not having a grounded circuit O AUN TO REPLACE THE BATTERY 1 Remove the right side of the faceplate Slide the new battery pack into the unit Replace the 4 retaining screws Connect the black and red cable Replace the cover CO N O O1 12 CPS1500AVR Guaranteed Uninterruptible Power System DEFINITIONS FOR LED INDICATORS Je A gt lt i Power On Wiring AVR Using Circuit Alarm Condition Fault Battery Breaker On Off Off Off Set Off Normal On Off Flash Off Set Off AVR Max boost 15 of input voltage for output regulation while input voltage is from 8 to 30 under nominal On Off On Off Set Off AVR Max buck 15 of input voltage for output regulation while input voltage is from 8 to 26 over nominal Off On Off Off On Set Two Beeps Utility Failure The UPS is providing battery power to the battery outlets Off On Off Off On Set Rapid Beeps Utility Failure The UPS is providing battery power to the battery outlets Rapid beeps indicate that the battery will run out of charge within a few minutes On Off On Off On Off Flash On Off Set Long Beep Overload Turn the UPS off and unplug at least one piece of equipment Wait 5 seconds reset the circuit breakers and restart the UPS Off Off Off On Up Long Beep Overload Turn the UPS o
31. ressly approved by the guarantee of this device could void the user s authority to operate the equipment For more information contact us at CyberPower Systems USA Inc 5555 12 Avenue East Suite 110 Shakopee MN 55379 Tel 952 403 9500 Fax 952 403 0009 E mail sales cyberoowersystems com Web www cyberopowersystems com Entire contents copyright 2001 CyberPower Systems USA Inc All rights reserved Reproduction in whole or in part without permission is prohibited PowerPanel and PowerPanel Plus are trademarks of CyberPower Systems USA Inc
32. rom 100v to 125v 5 Cold Start When enabled the UPS can start in the absence of AC power To maximize battery life it is recommended to keep this disabled 6 Default Restores settings to the factory defaults 7 Cancel Exits the window without saving changes 8 OK Exits the window and saves changes 9 Remote On Function This function is not available with this model POWERPANEL PLUS SCHEDULE MENU 1 Special Setting This setting allows you er to schedule a one time shutdown startup 4 EEP 2 Schedule Display This area displays the days dates times of any scheduled 2 fear es 6 shutdown startup i 3 Turn On Select the day date time that you want the system to start Must be scheduled in conjunction with a shutdown 4 Turn On Disabled When button states Turn On Disabled the UPS will restart according to the schedule When button states Turn On Enabled the UPS will not 3 restart according to the schedule CPS1500AVR Guaranteed Uninterruptible Power System 5 Clear Clears the selected item from the schedule 6 Add Adds an item to the schedule 7 OK Exits the window Please note You must click Add to add the item to the schedule 8 Turn Off Select the day date time that you want the system to shutdown This is optional and has no effect on whether your computer will shut down during a power failure 9 Weekly Setting Allows you to schedule a shutdown startup base
33. st version is available for download from www cyberpowersystems com downloads htm The software works in conjunction with the UPS to provide full protection to valuable computer systems applications and data In the event of a power failure PowerPanel Plus automatically saves and closes open files under auto assigned file names or existing file names after a software controlled delay The computer and UPS are automatically shutdown to conserve batter power Files with auto assigned names are saved in C PCTemp where C is the name of the main hard drive Files that have previously been saved will be saved in their Original location The use of PowerPanel Plus software is optional The UPS unit will provide full surge Suppression and battery backup without use of the software You must use the software if you wish to have the auto shutdwon feature Windows NT Windows 2000 and Windows XP have built in UPS monitoring functions that may be used instead of PowerPanel Plus PowerPanel Plus Main Menu i 1 Log Button Click to open the Log Window Power Button Exits the software Minimize Button Minimizes the software Setup Button Click to open the Setup 3 Window 4 Model Shows the model of the UPS Version Shows the hardware version 5 Status Bar Displays messages about the status of the software 7 8 Schedule Button Click to open the Schedule Window 8 amp PO N O OI CPS1500AVR Guarante
34. vent for which you want to make a claim for warranty service 3 When you contact CyberPower identify the Product the Purchase Date and request Return Materials Authorization RMA information from CyberPower 4 Pack and ship the Product to CyberPower as instructed in your RMA Show the RMA code on the shipping label or include it with the Product You MUST prepay all shipping costs and you are responsible for packaging and shipment CyberPower will inspect and examine the Product within ten 10 days of receipt If the Product is not as warranted CyberPower will repair or replace the Product and return it to you at CyberPower s expense or if CyberPower is unable to or decides not to repair or replace the Product if defective within a reasonable time CyberPower will refund to you the full purchase price you paid for the Product purchase receipt showing price paid is required 15 CyberPower POWER CONTROL GUARANTEE If you are the Initial Purchaser and the Product is still covered by the Limited Warranty the Power Control Guarantee provides protection for damage to equipment connected to the Product Connected Equipment subject to certain terms and limitations The Power Control Guarantee is not first dollar coverage CyberPower s obligation is reduced by any amounts that Initial Customer is entitled to recover from other sources regarding the Connected Equipment including insurance other warranty or extended warranty coverag
35. w for all item s of Initial Customer s Connected Equipment The Agreed Damage Amount for all items of Initial Customer s Connected Equipment shall be the lesser of the amount determined under Clause 1 or 2 below reduced by any amounts described in Clause 3 below 1 The fair market value of the Connected Equipment as established by the lower of a the average price the same or similar items are being sold for on E bay b the price list of Orion Blue Book on the date of occurrence or if such price list is no longer published a published or announced price list reasonably selected by CyberPower or c the lowest price the same or similar items can be purchased for in the United States or 2 The aggregate ceiling amount for all Connected Equipment as set forth below minus 3 The amount s of all payment you have or are entitled to receive from insurance other warranties extended warranties or from other sources or persons for the Connected Equipment or damage to such equipment so that CyberPower s maximum liability shall be reduced to reflect all such other payments or sources of recovery CyberPower CPS1500AVR 500 000 4 If CyberPower replaces the connected equipment or pays to the Initial Customer the Agreed Damage Amount the Initial Customer shall transfer all item s to CyberPower without warranty by the Initial Customer but free of lien or other interest 16 CPS1500AVR Guaranteed Uninterruptible Power System CON
36. ware To use the software self test open the main window and then click on setup refer to page 8 Click the red run button The unit will cycle to battery and emit an audible beep With the software self test the unit will switch back to AC power automatically CyberPower REPLACING THE BATTERY CAUTION Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery Service the battery under the supervision of personnel knowledgeable of batteries and their precautions CAUTION Use only the specified type of battery See your dealer for replacement batteries CAUTION The battery may present the risk of electrical shock Do not dispose of batteries in a fire as it may explode Follow all local ordinances regarding proper disposal of batteries CAUTION Do not open or mutilate the batteries Release electrolyte is harmful to the skin and eyes and may be toxic CAUTION A battery can present a high risk of short circuit current an electrical shock Take the following precautions before replacing the battery Remove all watches rings or other metal objects Only use tools with insulated handles DO NOT lay tools or other metal parts on top of battery or any battery terminals Wear rubber gloves and boots Determine if the battery is inadvertently grounded If inadvertently grounded remove source of ground CONTACT WITH A GROUNDED BATTERY CAN RESULT IN ELECTRICAL SHOCK The likelihood of such shock will be
37. y LIMITED WARRANTY CyberPower warrants to you the Initial Purchaser that the Product will be free from defects in material and workmanship for three years from the date of original purchase subject to the terms of this Limited Warranty To be covered you must still be the owner of the Product at the time of the failure that results in the claim made under this Limited Warranty Your exclusive remedy and CyberPower s sole obligations are as follows for the Product If a the CyberPower Product you purchased and still own is defective in material or workmanship under this Limited Warranty or any applicable warranty imposed by law and b all Limited Warranty requirements have been met CyberPower will repair or replace the Product if it proves to be defective in material or workmanship during the Warranty Period To make a Limited Warranty claim on a Product you must do the following 1 Complete and return the CyberPower Warranty Registration Card or provide reasonable proof of purchase for example a sales receipt that establishes you as the Initial Customer the original end user consumer purchaser of the Product and prove that the Product was purchased within three 3 years of the event for which you want to make a claim for warranty service 2 Call CyberPower at 952 403 9500 write to CyberPower at 5555 12th Ave East Suite 110 Shakopee MN 55379 or e mail CyberPower at tech cyberpowersystems com within ten 10 days of the e
Download Pdf Manuals
Related Search