LevelOne GVT-4001 network media converter
Contents
1. and operation mode for Copper Fiber port The default value of Dipswitch is OFF m 10 100 1000Base T to 1000Base LX SX converter module S W No Status Description ON LLF Enable 1 OFF LLF Disable ON Pure converter mode OFF Switch converter mode ON Reserved 3 OFF Reserved Link Loss Forwarding When LLF is enabled it will allow copper port link failure to be reported to the Fiber side and also allow Fiber link failure to be reported to the copper side Therefore a link loss forward feature is provided in both copper and Fiber side Pure Converter mode When pure converter mode is enabling on it operates with the minimum latency The transmission flow does not wait until entire frame is ready 8 but instead it forwards the received data immediately after the data being received And TP port should be forced at 1000M in this application When DIP Switch is in Switch Converter mode off the converter function is same as Switch Hub Note a Please don t change the DIP switch setting when copper or fiber port is transmitting or receiving data It may cause some data error b Please power off then power on when you change the DIP switch setting Converters module Installation This installation is only for mounted in converter chassis converter module You can follow the steps below to install modular converters A Remove the blank bracket by rotating thumbscrew counterclockwise Put the b2. MDIX or pure 1000 Base T network up to 550m for multi mode fiber or 80 kilometers for single mode fiber The Giga Fiber Converter gives you the option to choose from the most popular fiber cabling connectors SC multi mode fiber connector The Modular Giga Fiber Converters provides you with one Fiber connector for your fiber optic cable and one Ethernet RJ 45 port Auto MDI MDIX for your 10 100 1000BaseTX copper cable or pure 1000 Base T copper cable connection There are DIP switches to set the operation mode for UTP Fiber ports and link loss forwarding function Features Standard LED Indicators Connector Fiber parameters Link Loss Forward IEEE 802 3 10BASE T IEEE 802 3u 100BASE TX IEEE 802 3ab 1000BaseT IEEE 802 3z 1000BaseSX LX standards IEEE 802 3x Flow Control and Back pressure Power Green UTP SPD 1000Mbps 100Mbps Lnk Act UTP FIBER FDX UTP Full Duplex mode Half Duplex or Link down FIBER Full Duplex mode Link down Fiber Duplex SC MINI GBIC 3 3V WDM RJ 45 Socket CAT 5e 10 100 1000Mbps Twisted Pair cable Auto MDI MDI X and Auto Negotiation Function Support Fiber Core Multi Mode 62 5 125um 50 125um Single Mode 9 125um Wavelength 850nm Multi mode 1310nm Single mode 1310nm WDM TX 1550nm WDM RX Fiber Distance 550M Multi Mode Fiber 80 KM Single Mode Fiber WDM Single mode 10KM 20KM Copper Fiber If copper port link down then media converter will forced fiber t
3. X and 6 LED Indicators SPD LK ACT FDX Fiber LK ACT FDX COL and PWR LK ACT 1010011000 FOX SFP GVT 4000 SPD O PWR O O mn RX o 9L O O O LKIACT 10100 1000 L FOXICOL 1000Base X GVT 4001 1 RJ 45 Port 3 DIP Switch 2 LED 4 Fiber Connector Rear Panel The rear panel contains a power socket This power socket accepts DC9V voltage and minimum 0 7A supplied current 9 OS Ports B Copper Port Auto MDI MDIX of 10 100 1000Base T to 1000Base LX SX converter module The Ethernet ports will auto sense for 10Base T 100Base TX or 1000Base T connections Auto MDI MDIX means that you can connect to another Switch or workstation without changing non crossover or crossover cabling m Fiber Port This port is for 1000Base SX with SC connections LED Indicators There are 6 diagnostic LEDs located on the Front panel of converter module They provide real time information of system and optional status The following table provides description of the LED status and their meanings for Modular Giga Fiber Converter m 10 100 1000Base T to 1000Base LX SX converter module AAA m rom 1000Mbps UTP Speed 100Mbps UTP Speed 10Mbps UTP Speed LNK ACT Full duplex mode FDX UTP Half duplex mode or link down LNK ACT Blinks Transmitting Fiber Full duplex mode FDX COL Fiber DIP switch The DIP switch is used to configure operation mode for LLF Link Loss Forwarding
4. lank bracket aside but don t discard blanket bracket B Open the rack mount ear kit The kit contains two rack mount ear with thumbscrew and four screws C Attach rack mount ear on both sides of the modular converter by using a screwdriver to secure the rack mount ears Sa Auto MOUMDIX PWR TX Nx ler SPD Ea DAT type Fast Fib Eo ue er Converter FDX Lact Multi mode E y D Install the modular converter by inserting it into the guides and sliding it in until it stops Press it firmly until the power plug in the chassis plugs into the modular converter receptacle Slide the modular converter in smoothly E Gently push the thumbscrews in and turn clockwise to tighten Do not over tighten the thumbscrews Cabling m Using four twisted pair Category 5e cabling for copper port connection The cable between the converter and the link partner switch hub workstation etc must be less than 100 meters 323 ft long W Fiber segment using single mode connector type must use 9 125 um single mode fiber cable You can connect two devices in the distance of 10 Kilometers in full duplex operation For half duplex operation the recommended maximum distance is 412 meters 1 352 ft m Fiber segment using multi mode connector type must use 50 or 62 5 125 um multi mode fiber cable You can connect two devices up to 550m distances Troubles shooting Check the configuration DIP switch I
5. o link down Fiber Copper If Fiber port link down the media converter will forced copper port to link down Switch architecture 16Kbyte Pure converter mode Jumbo Frame 2Kbyte Switch converter mode ETE Stand alone external adapter DC 9V 0 7A Power 4 3 Watts max Consumption Operating Store and Forward OC to45 C 32 F to 113 F Temperature Operating 10 to 90 Humidity Storage 40 C 70 C environment Storage Ae 10 to 90 Humidity 120mm x 85mm x 26mm FCC Class A CE Package Contents Beware of which type of converter module that you have purchased And please refer to the package content list below to verify them against the checklist W Stand alone converter module package contains following items The Giga Fiber Converter GVT 4000 or GVT 4001 gt AC DC Power Adapter User Guide Compare the contents of your Converter with the standard checklist above If any item is damaged or missing please contact your local dealer for service Hardware Description The Giga Fiber Converter dimension L x W x H 120mm x 85mm x 26mm 0 0 0 0 0 0 0 0090 95 000 0000 0 o o oj o o o oo o o o jo o o o o o o ollo o o ojjo o o ojjo o o ojjo o o ojo Front Panel 10 100 1000Base T to 1000Base LX SX converter module The Front Panel of the 10 100 1000Base T to 1000Base LX SX converter module consists of one Giga Fiber port one copper Port Auto MDI MDI
6. t must be setting in the same operation mode with the link partner Select the proper Copper Fiber cable to construct your network The single mode converter must use single mode fiber cable Please check that you are using the right cable Don t both use multi mode and single mode Link loss Forwarding problem When using a mixture of GVT 4000 4001 Hardware versions 1 and 2 please note the differences in the dip switches 1 GVT 4000 4001 Hardware version 1 S WNo Status Description ON Fiber in 1000Mbps Full Duplex OFF Fiber Auto Negotiation ON UTP LLF Enable OFF UTP LLF Disable ON Fiber LLF Enable OFF Fiber LLF Disable 2 GVT 4000 4001 Hardware version 2 S W No Status Description ON LLF Enable i OFF LLF Disable ON Pure converter mode OFF Switch converter mode ON Reserved OFF Reserved For GVT 4000 4001 Hardware version 1 please ensure that either dip 2 or dip 3 are set to ON and not both at the same time
7. y lt 0 Ey 0 MENA 0 I JEE E Copper to Fiber Stand Alone Media Converter User Manual Part No Model No Description 531404 GVT 4000 10 100 1000Base T to SFP mini GBIC 10 100 1000Base T to 1000SX SC Multi mode 550m 531402 GVT 4001 Ver 2 00 0812 Content ge AA II e ERU IA AI NDA NS 1 a Ea aN A DAE E He Reise t Ces 2 PACKAGE CONTENTS EN ie nasse 4 Hardware Description tied at AA AAA AAA AAA 5 lcu iil MP E Cr EE 3 REAR PAN EIs S Se tes ea en o Gi at ala 6 PORTS E 7 EPTPINDICA TOR Sit ee rel 7 DIP SWITCH ponani easa a E a a EE AR EE AA ios idas 8 Converters module Installation ooccccccnnnnnnnonnncnnncncnnncccnnnnnnnnnnnnnnnnonannnnnnnnos 10 C ABLINO A RE RES Nee reine 11 1roubles sheolinge Ar ra 12 Introduce B The Giga Fiber Converter has two types of module package one is stand alone converter module And another one is mounted in converter chassis converter module m The Giga Fiber Converter is a cost effective solution for the converting 10 100 1000Base Tx Auto MDI MDIX and pure 1000 Base T to 1000Base SX SFP Itcan be slotted in Multi Converter Chassis on up to 10 optional modular converter units which allows your network connectivity to be more flexible It also can use stand alone without slot in Multi Converter Chassis m The Giga Fiber Converter will allow you to extend the cabling distance of your 10 100 1000BaseTX Auto MDI
Download Pdf Manuals
Related Search