Antec P183
Contents
1. There are 120 x 25mm TriCool fans pre installed at the rear and top of the case They have external three speed switches that let you choose between quiet performance or maximum cooling on each of the fans The default speed setting is Low The two fans are mounted so that the air is blowing out of the case There are externally accessible switches for these fans located at the top rear of your case Size 120 x 25mm TriCool fan Rated Voltage 12V Operating Voltage 10 2V 13 8V Speed Input Air Flow Static Acoustic RPM Current Pressure Noise High 0 24A 2 2 m min 2 5mm H20 2000 Max 79 CFM 0 10 inch H20 Medium 0 204 1 6 m min 1 5mm H20 1600 56 CFM 0 06 inch H20 Lo 0 13A 1 1 m min 0 9mm H20 1200 39 CFM 0 04 inch H20 Note The minimum voltage to start a 120mm TriCool fan is 5V We recommend that you set the fan speed switch to High if you choose to connect the fan s to a fan control device or to the Fan Only connector found on some Antec power supplies A fan control device regulates the fan speed by varying the voltage which may start as low as 4 5V to 5V Connecting a TriCool fan set on Medium or Low to a fan control device may result in the fan not being able to start because the already lowered voltage from the fan control device will be further reduced by the TriCool circuitry below 5V 10 4 2 OPTIONAL FANS There are three optional 120mm fan mounts two front fans in front of t2. for switches 3 5 REWIRING MOTHERBOARD HEADER CONNECTIONS There may come a time when you need to reconfigure the pin out of a motherboard header connector Examples could be for your USB header audio input header or some other front panel connector such as the Power Button connector Before performing any work please refer to your motherboard manual or your motherboard manufacturer s website to be sure of the pin out needed for your connector And we strongly recommend making a notated drawing before beginning work so that you can recover if your work gets disturbed 1 Determine which wires you need to remove in order to rewire your plug to match the USB pin outs on your motherboard refer to your motherboard user s manual Working on one connector at a time use a very small flathead screwdriver or similar tool to lift up on the black tab located beside the gold posts squares This will allow you to easily slide out the pins from the USB plug 2 Working carefully so as not to damage the wires connectors or pins slowly remove the pin from the connector Repeat these steps for each wire you need to change 3 Working carefully so as not to damage the wires connectors or pins slowly reinsert the pin into the correct slot of the connector then snap closed the black tab that was lifted in step 1 Repeat these steps for each wire you need to change COOLING SYSTEM 4 1 TRICOOL FANS Rear Top TriCool Fan
3. panel for your motherboard If the panel provided with the case isn t suitable please contact your motherboard manufacturer for the correct I O panel Align your motherboard with the standoff holes and remember which holes are lined up Not all motherboards will match with all the provided holes this is normal and won t affect its functionality Remove your motherboard by lifting it up Install standoffs as needed and put the motherboard back in Screw in your motherboard to the standoffs with the provided Phillips head screws 2 6 INTERNAL 3 5 DEVICE INSTALLATION With the front bezel facing you swing the front door open It can swing 2702 so the door will be parallel with the side of the case You can see there are four 5 25 and one 3 5 external drive bays Inside the case there are two 3 5 drive cages which can house up to six hard drives Note We recommend using the lower HDD cage to maximize cooling and quiet computing Upper HDD Installation 1 Remove the thumbscrew holding the upper HDD cage 2 Remove the HDD cage from its position by pulling the ring toward you 3 There are two HDD trays inside the cage Squeeze the metal clips on each side of the tray and slide the tray out 4 Mount your hard drive into the drive tray with the special screws provided Don t over tighten the screws as this will reduce the vibration and noise dampening ability of the silicone grommets Note Always mount the HDD with the thicke
4. Antec Believe it USER S MANUAL TABLE OF CONTENTS INTRODUCTION 1 1 Case Specifications asso Ge ot bebo e a tb Ue pt opa adito do tad ture oua 3 1 2 Baue E SEE 3 HARDWARE INSTALLATION GUIDE 2 1 Sg UD aaa dd 4 2 2 Power SUDDIV Instala aa 4 2 3 CP Series Power Supply MOUTH iic b vi Ee Ep EG DE o ta eed iid ineo 5 2 4 Cable Managemelibo EE 5 2 5 Motherboard Le e UE gie EE 5 2 6 intemal s 5 IECH EN ON DEE 6 2 7 External 3 5 Device Installation n eve ter av e nes euntis 7 2 8 External 5 25 Device InstalldtiODuni ce idet usto os 7 CONNECTING THE FRONT I O PORTS 3 1 USBZ 0 POS A ais 8 3 2 CSA FA POr S ean T a E E A 8 3 3 AC G7 J AD AUCiIO e EE 8 3 4 Switch and LEDCONNECtO Srta 9 3 5 Rewiring Motherboard Header Connections eee 9 COOLING SYSTEM 4 1 HR L t e EE 10 4 2 Optoma RAS at na 11 4 3 Washable Air Fe Sets E ta 11 P183 User s MANUAL At Antec we continually refine and improve our products to ensure the highest quality It s possible that your new case will differ slightly from the descriptions in this manual This isn t a problem it s simply an improvement As of the date of publication all features descriptions and illustrations in this manual are correct Disclaimer This manual is intended only as a guide for Antec s computer enclosures For more comprehensive instructions on installing the motherboard and peripherals please refer to the user s manuals that come with those compon
5. back of the case with the screws provided Slide the small plastic piece to the rear of the case to fully extend the other opening Slide both the large and small plastic pieces all the way to the front of the case to close the openings when finished with the hard drive installation Tighten the two thumbscrews on the plastic structure 2 3 Your Antec P183 enclosure comes with a power supply mounting adapter to mount either a standard size power supply or Antec s exclusive CP Series high performance power supply This adapter is mounted to the chassis with standard Phillips head screws In order to install a CP Series power supply remove the mounting plate first CP SERIES POWER SUPPLY MOUNT 2 4 CABLE MANAGEMENT There is a cable management compartment between the motherboard and right side panel You can tuck or route excess cables in this compartment 2 5 Remove both side panels Choose the cables you would like to pass through the holes behind the motherboard tray and pull them out of the power supply chamber toward the right side of the case Use the cable ties provided to hold them in place Feed the cables back through the insertion point nearest the destination of the cable Connect the cable and then pull the slack back to the right side of the case MOTHERBOARD INSTALLATION Lay the case down with the open side facing up The drive cages and power supply should be visible y Make sure you have the correct I O
6. bays Motherboard Size Mini ITX microATX Standard ATX Front I O Panel 2 x USB 2 0 1 x eSATA AC 97 HD Audio In and Out 1 2 DIAGRAM 120mm rear TriCool fan 120mm top TriCool fan Washable air filters Motherboard mount Power supply mount 5 25 drive bays 3 5 drive bays Front I O panel zeg GD Gime Gas GERRY wh db A 4 D De LA ooo ee E 4 HARDWARE INSTALLATION GUIDE 2 1 2 2 SETTING UP Place the case upright on a flat stable surface with the rear of the case facing you Remove the thumbscrews from the right side panel Grip the panel at the top and bottom and slide it toward you to open the case Remove the screws from the left side panel Grip the panel at the top and bottom and slide it toward you to remove the left side panel Note Do not use your fingernails to pry or lift the panels POWER SUPPLY INSTALLATION Between the two chambers there is a plastic structure that lets you run the cables to the upper and lower chambers It is a two piece structure one large and one small Both pieces can slide back and forth to adjust the openings Loosen the two thumbscrews holding the plastic structure Slide the large piece all the way to the rear of the case to fully extend the opening Take any cables that will not be routed through the cable management chamber and carefully guide them through the openings to the upper chamber Fasten the power supply to the
7. c MX 1 to run at the same speeds as internally installed hard disks 3 3 AC 97 HD AUDIO PORTS There is an Intel standard 10 pin AC 97 connector and an Intel 10 pin HDA High Definition Audio connector linked to the front panel of the case Signal Names Signal Names HDA AC 97 MIC2 L ME MIC In AGND 2 GND MIC2 R 8 MIC Power ACC 4 no FROR 5 Gre Out R 6 MC2JD 6 LineOut R LB Key no pin NN Key no pin 9 FROL 9 One gu Line Out L You can connect either the AC 97 or the HDA connector depending on your motherboard Locate the internal audio connectors from your motherboard or sound card and connect the corresponding audio cable Consult your motherboard or sound card manual for the pin out positions Even if your system supports both standards only use one connector 8 3 4 POWER SWITCH RESET SWITCH HARD Disk DRIVE LED CONNECTORS Connected to your front panel are LED and switch leads for power reset and HDD LED activity Attach these to the corresponding connectors on your motherboard Consult your motherboard manual for specific pin header locations For LEDs colored wires are positive White or black wires are negative If the LED does not light up when the system is powered on try reversing the connection For more information on connecting LEDs to your motherboard see your motherboard manual Note Polarity positive and negative does not matter
8. e air filters at least once a month initially The frequency will change depending on environmental conditions and system usage Users who run their systems 24 7 will have to check their filters more often than those who don t run their systems every day To remove the hinged filters 1 Push one of the fan grills at the right middle edge to separate the grill from the chassis The filter will still be attached by a hinge on the opposite side of the filter Swing the filter out so that it is perpendicular to the case 2 Using both hands lift the filter up and angle the base of the filter toward you until both tabs detach from the hinge Remove the filter To remove the drive bay cover filters 1 Depress the tabs of the filter inward and pull the filter away from the front panel 11 Antec Inc 47900 Fremont Blvd Fremont CA 94538 USA tel 510 770 1200 fax 510 770 1288 Antec Europe B V Stuttgartstraat 12 3047 AS Rotterdam Netherlands tel 31 0 10 462 2060 fax 31 0 10 437 1752 Customer Support US Canada 1 800 22ANTEC customersupport antec com Europe 31 0 10 462 2060 europe techsupport antec com www antec com Copyright 2009 Antec Inc All rights reserved All trademarks are the property of their respective owners Reproduction in whole or in part without written permission is prohibited 12
9. ents The P183 does not come with a power supply PSU Make sure you choose a power supply that is compatible with your computer components and has a long enough power harness to reach your motherboard and peripheral devices We recommend our CP series TruePower or Signature Series power supplies for the latest ATX specification compliance broad compatibility and energy saving capability Although care has been taken to prevent sharp edges in your Antec case we strongly recommend taking the appropriate time and care when working with it Avoid hurried or careless motions Please use reasonable precaution This manual is not designed to cover CPU RAM or expansion card installation Please consult the motherboard manual for specific mounting instructions and troubleshooting Before proceeding check the manual for your CPU cooler to find out if there are steps you must take before installing the motherboard While installing hardware keep your case on a flat stable surface 1 1 CASE SPECIFICATIONS Case Type Advanced Mid Tower Dimensions 514mm H x 205mm W x 507mm D 20 3 H x 8 1 W x 19 9 D Weight 31 lbs 14 kg Cooling 1 x Rear 120mm TriCool fan 1 x Top 120mm TriCool fan 1 x Lower chamber 120mm TriCool fan optional 1 x Front 120mm fan mount optional 1 x Middle 120mm fan mount optional Drive Bays 11 Drive Bays 4x External 5 25 drive bays 1x External 3 5 drive bay 6xInternal 3 5 drive
10. he upper HDD cages and a middle fan at the rear end of the upper HDD cage These three fans should be installed so that the air is blowing into the case from the front Front Fans The front fans are designed to enhance HDD cooling Middle Fan If you decide to mount any HDD into the upper cage you will not be able to use the middle fan The middle fan is specially designed to cool the graphics card and even a dual graphics card configuration In this case the HDD cage acts as a duct drawing fresh cool air from the front of the case You can choose to mount only the middle fan or you can mount both the front and the middle fans to enhance the cooling as two fans will serve a push and pull function bringing the air in more efficiently 1 Find the two fan wire brackets from the tool bag 2 Install the wire brackets into the HDD cage 3 Clip the fan into position Note In order to build a quieter system we recommend NOT installing the optional fans unless it is necessary for cooling If you choose to install them we recommend using Antec 120mm TriCool fans and setting the speed to Low 4 3 WASHABLE AIR FILTERS There are two hinged washable filters located behind the front door as well as additional filters covering all of the external drive bay covers Occasionally it will be necessary to wash the air filters Not washing the filters may result in high system temperatures and possible stability problems We recommend checking th
11. ide the device into the drive bay until it clicks into place 5 Connect a small 4 pin connector from the power supply to the 4 pin connector on the floppy drive py 2 8 EXTERNAL 5 25 DEVICE INSTALLATION There are four 5 25 drive bays that need a total of eight drive rails 1 Carefully remove the drive bay cover filter assembly by pressing the two tabs inward then remove the metal plate covering the drive bay 2 Mount the drive rails onto the sides of the 5 25 device Make sure the metal tab is angled away from the drive 3 Slide the device into the drive bay until it clicks into place 4 Mount the other devices accordingly 5 Connect the appropriate Molex or SATA connector from the PSU to the power connector on each of the devices CONNECTING THE FRONT I O PORTS 3 1 USB 2 0 Connect the front I O panel USB cable to the USB header pin on your motherboard Check the motherboard manual to ensure that it matches the table below Pin Signal Names Pin Signal Names USB Power 1 USB Power 2 Negative Signal 1 Negative Signal 2 0000O OOQO0O0 Positive Signal 1 6 Positive Signal 2 Lr eer pow ES CCA 9 10 9 o Key No Connection Empty Pin 3 2 ESATA You will find a SATA connector on a cable attached to the front ports This internal SATA connector is designed to connect to a standard SATA connector on your motherboard This will allow high speed external hard disk enclosures such as the Ante
12. r side of the silicone grommets facing up Slide and lock the tray back into the cage Slide the cage back into the case and fasten the thumbscrew Find the right Molex or SATA connector on the power supply and connect it to the hard drive Repeat the same procedure for the other drives po x M n Lower HDD Installation 1 Remove the thumbscrew holding the lower HDD cage 2 Remove the HDD cage from its position by pulling the ring toward you 3 You can mount four hard drives inside the cage They are mounted vertically with the silicone grommets sitting at both sides 4 Mount your hard drive into the drive cage with the special screws provided Don t over tighten the screws as this will reduce the vibration and noise dampening ability of the silicone grommets Note Always mount the HDD with the thicker side of the silicone grommets facing up 5 Slide the cage back into the case and fasten the thumbscrew 6 Find the right Molex or SATA connector on the power supply and connect it to the hard drive 7 Repeatthe same procedure for the other drives 2 7 EXTERNAL 3 5 DEVICE INSTALLATION There is one external 3 5 drive bay 1 Carefully remove the plastic drive bay cover and metal plate covering the drive bay Find a pair of 3 5 drive rails in the included hardware kit box 3 Mount the drive rails onto the sides of the 3 5 device Make sure the metal portion is angled on the outside and facing forward 4 Sl
Download Pdf Manuals
Related Search