LG L1942SM Monitor
Contents
1. The screen color is e Check if the signal cable is properly connected mono or abnormal and use a screwdriver to fasten if necessary e Make sure the video card is properly inserted in the slot e Set the color setting higher than 24 bits true color at Control Panel Settings The screen blinks e Check if the screen is set to interlace mode and if yes change it to the recommend resolution Have you installed the display driver Have you installed the Be sure to install the display driver from the display display driver driver CD or diskette that comes with your display Or you can also download the driver from our web site http Avww ige com Do you see an e Make sure to check if the video card supports Unrecognized monitor Plug amp Play function Plug amp Play VESA DDC monitor found message Specifications 17 inch Display 17 inches 43 2 cm Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 43 2 cm 0 264 mm pixel pitch Sync Input Horizontal Freq 30 83 kHz Automatic Vertical Freq 56 75 Hz Automatic Input Form Separate TTL SOG Sync On Green Video Input Signal Input 15 pin D Sub Connector Input Form RGB Analog 0 7 Vp p 75 ohm Resolution Max VESA 1280 x 1024 75 Hz Recommend VESA 1280 x 1024 60 Hz Plug amp Play DDC 2B Power On Mode 32 W Typ Consumption Sleep Mode lt 1W Off Mode lt 1W Dimensions With Stand Without Sta2. When you encounter problems such as blurry screen blurred letters screen flicker or tilted screen while using the device or after changing screen resolution press the AUTO SET function button to improve resolution Control Panel Functions Front Panel Controls v A MENU AUTO SET b F ENGINE VOLUME Control Function Use this button to enter or exit from the On Screen Display MENU Button OSD LOCKED UNLOCKED This function allows you to lock the current control settings so that these settings are not inadvertently changed To lock the OSD settings press and hold the MENU button for several seconds The message OSD LOCKED appears A You can unlock the OSD settings at any time by pushing the MENU button for several seconds The message OSD UNLOCKED appears Control Panel Functions Control Function Use these buttons to select or adjust functions in the 2 WV ENGINE On Screen Display For more information refer to page A15 J ENGINE VOLUME Use these buttons to select or adjust functions in the On Screen Display Use wW buttons to decrease or increase the speaker volume Q C E10 AUTO SET Use this button to select an icon in the On Screen Button Display AUTO IMAGE ADJUSTMENT When adjusting your display settings always press the AUTO SET button prior to entering the On Screen Display OSD This will automatically adjust your display
3. 13 56 inches Depth 18 48 cm 7 28 inches 5 99 cm 2 36 inches Net 3 45 kg 7 61 Ibs Tilt 5 20 AC 100 240V 50 60Hz 0 8A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached Detached O Wall outlet type or PC outlet type a Information in this document is subject to change without notice Specifications Preset Modes Resolution Display Modes Resolution 640 x 350 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 10 1152 x 870 11 1152 x 900 12 1280 x 1024 13 1280 x 1024 O 0ONOQOAAON Indicator On Mode blue Sleep Mode flicker Off Mode Off Horizontal Freq kHz 31 469 31 468 31 469 37 500 37 879 46 875 49 725 48 363 60 123 68 681 61 805 63 981 79 976 Vertical Freq Hz Recommend Mode Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device 1 Place the monitor with its front facing downward on a soft cloth Good Position Bad Position Warning You can hurt your finger 3 Install the Wall mount plate Wall mount plate Separate purchase This is stand type or wall mount type and is connectable with Wall mount plate Please refer to the installation guide for more details which is provided when Wall mount plate is purchas
4. image appears Is the power cord of the Check and see if the power cord is connected display connected properly to the power outlet Is the power indicator Press the Power button light on Is the power on and the Adjust the brightness and the contrast power indicator blue or green Is the power indicator If the display is in power saving mode try moving flickering the mouse or pressing any key on the keyboard to bring up the screen e Try to turn on the PC Do you see an OUT OF This message appears when the signal from the RANGE message on PC video card is out of horizontal or vertical the screen frequency range of the display See the Specifications section of this manual and configure your display again Do you see a CHECK his message appears when the signal cable SIGNAL CABLE between your PC and your display is not message on the connected Check the signal cable and try again screen Do you see a OSD LOCKED message on the screen Do you see OSD e You can secure the current control settings LOCKED when you so that they cannot be inadvertently changed push MENU button You can unlock the OSD controls at any time by pushing the MENU button for several seconds the message OSD UNLOCKED will appear Troubleshooting Display Position is incorrect On the screen background vertical bars or stripes are visible
5. image to the ideal settings for the current screen resolution size display mode PROCESSING AUTO The best display mode is IMAGE ADJUSTMENT L1742SM 1280x1024 L1942SM 1280x1024 Use this button to turn the display on or off 5 Power Indicator This Indicator lights up as blue when the display is operating normally On Mode If the display is in Sleep Mode Energy Saving this indicator changes to flicker On Screen Display OSD Control Adjustment Screen Adjustment Making adjustments to the image size position and operating parameters of the display is quick and easy with the On Screen Display Control system A short example is given below to familiarize you with the use of the controls The following section is an outline of the available adjustments and selections you can make using the OSD NOTE a Allow the display to stabilize for at least 30 minutes before making image adjustments To make adjustments in the On Screen Display follow these steps MENU VW A AUTO SET V A MENU Press the MENU Button then the main menu of the OSD appears To access a control use the W or amp Buttons When the icon you want becomes highlighted press the AUTO SET Button Use the wW A Buttons to adjust the image to the desired level Use the AUTO SET Button to select other sub menu items Push the MENU Button once to return to the main menu to select another function Push the MENU Button twice to exit f
6. Any horizontal noise appearing in any image or characters are not clearly portrayed Display image is incorrect e Press the AUTO SET button to automatically adjust your display image to the ideal setting If the results are unsatisfactory adjust the image position using the H position and V position icon in the on screen display e Press the AUTO SET button to automatically adjust your display image to the ideal setting If the results are unsatisfactory decrease the vertical bars or stripes using the CLOCK icon in the on screen display e Press the AUTO SET button to automatically adjust your display image to the ideal setting If the results are unsatisfactory decrease the horizontal bars using the PHASE icon in the on screen display e Check Control Panel gt Display gt Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting Set the color setting higher than 24 bits true color Important a Check Control Panel gt Display gt Settings and see if the frequency or the resolution were changed If yes readjust the video card to the recommend resolution a The setting method can differ by computer and O S Operation System and resolution mentioned above may not be supported by the video card performance In this case please ask to the computer or the video card manufacturer Troubleshooting Display image is incorrect
7. User s Guide L1742SM L1942SM Make sure to read the Important Precautions before using the product Keep the User s Guide CD in an accessible place for future reference Sec the label attached on the product and give the information to your dealer when you ask for service Important Precautions This unit has been engineered and manufactured to ensure your personal safety however improper use may result in potential electrical shock or fire hazards In order to allow the proper operation of all safeguards incorporated in this display observe the following basic rules for its installation use and servicing On Safety Use only the power cord supplied with the unit In case you use another power cord make sure that it is certified by the applicable national standards if not being provided by the supplier If the power cable is faulty in any way please contact the manufacturer or the nearest authorized repair service provider for a replacement The power supply cord is used as the main disconnection device Ensure that the socket outlet is easily accessible after installation Operate the display only from a power source Indicated in the specifications of this manual or listed on the display If you are not sure what type of power supply you have in your home consult with your dealer Overloaded AC outlets and extension cords are dangerous So are frayed power cords and broken plugs They may result in a shock or fi
8. ed Kensington Security Slot Connected to a locking cable that can be purchased separately at most computer stores Digitally yours saan La
9. endicularity direction 5 Once assembled take the monitor up carefully and face the front side Important This illustration depicts the general model of connection Your monitor may differ from the items shown in the picture Do not carry the product upside down holding only the stand base The product may fall and get damaged or injure your foot Connecting the Display Disassembling the stand 1 Puta cushion or soft cloth on aflat 2 Place the monitor face Down on surface the cushion or soft cloth 3 Change your lock on the product as it follows and turn it in the arrow direction If you can t release the stand base even the locking knob is at a release position Please push the indicated knob down and retry it Bes ANA ER 4 Pull out the Stand to remove Connecting the Display 5 Pushing the PUSH button Take the stand base from stand body Warning You can hurt your finger Good Position Bad Position a Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is turned off Positioning your display 1 Adjust the position of the panel in various ways for maximum comfort a Tilt Range 5 20 gt Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position the forward tilt angle of the monitor should not exceed 5 degrees Connecting the Display Using the Com
10. ge to the screen and cause image burn in Make sure to use a screen saver on the product Burn in and related problems are not covered by the warranty on this product On Cleaning Unplug the display before cleaning the face of the display screen Use a slightly damp not wet cloth Do not use an aerosol directly on the display screen because over spraying may cause electrical shock On Repacking Do not throw away the carton and packing materials They make an ideal container in which to transport the unit When shipping the unit to another location repack it in its original material On Disposal he fluorescent lamp used in this product contains a small amount of mercury Do not dispose of this product with general household waste a Disposal of this product must be carried out in accordance to the regulations of your local authority Connecting the Display Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is turned off Connecting the stand 1 Place the monitor with its front facing downward on a soft cloth 2 Assemble the Stand Body into the product in the correct direction as shown in the picture Make sure you push it until you hear it click Hinge Body A Stand Body 3 Assemble the Stand Base Front Rear into the Stand Body in the correct direction Stand Body Stand Base 4 Tie down the base lock to perp
11. ite balance function again This function will be enabled only when the input signal is an analog signal On Screen Display OSD Selection and Adjustment mm The OSD screen will appear when you touch the ENGINE button on the left bottom of the monitor Menu Name J ENGINE gt ser fe menu Main menu Sub menu Description JENGINE 4 El vl MOVIE This feature lets you easily select the best desired INTERNET image condition optimized to the environment ambient illumination image types etc MOVIE For animation images in videos or movies INTERNET For text images Word processing etc ENGINE E sere uga USER User You can manually adjust brightness ACE or RCM You can save or restore the adjusted value even when using a different environment Brightness Adjusts screen brightness ACE Adaptive Clarity Enhancer Selects the clarity mode ee Sie RCM Real Color Management Selects the color mode EE Not applied se Green enhance EE Flesh tone EGEE Color Enhance Select the sub menu using the AUTO SET button and save the YES value using the wW A buttons ie ae eS ee mae NORMAL This is under normal operating conditions E DEMO This is just for advertising to customer in the shops It s setting is same with Movie mode and age screen is divided by half Troubleshooting Check the following before calling for service No
12. menu languages on the monitor may differ from the manual Main menu Sub menu CONTRAST 9 Ome 1H 50 CONTRAST GAMMA GAMMA r Om 0 s MENU Exit Decrease Increase SET Select another sub menu PRESET SRGB 6500K 9300K RED le GREEN Decrease BLUE _ H Increase _ SET Select another sub menu BRIGHTNESS On Screen Display OSD Selection and Adjustment Description To adjust the brightness of the screen To adjust the contrast of the screen Set your own gamma value 50 0 50 On the monitor high gamma values display whitish images and low gamma values display high contrast images e SRGB Set the screen color to fit the SRGB standard color specification e 6500K Slightly reddish white e 9300K Slightly bluish white Set your own red color levels Set your own green color levels Set your own blue color levels On Screen Display OSD Selection and Adjustment Main menu TRACKING TRACKING VERTICAL B Ome H 50 Yy PHASE A 1H 50 SHARPNESS A H 5 MENU Exit Decrease Increase SET Select another sub menu Sub menu Description HORIZONTAL To move image left and right VERTICAL CLOCK PHASE SHARPNESS To move image up and down To minimize any vertical bars or stripe
13. nd amp Weight Width 36 96 cm 14 55 inches 36 96 cm 14 55 inches Height 39 13 cm 15 41 inches 31 51 cm 12 41 inches Depth 18 48cm 7 28 inches 5 90 cm 2 32 inches Net 3 0 kg 6 62 Ibs Tilt Range Tilt 5 20 Power Input AC 100 240V 50 60Hz 0 8A Environmental Operating Conditions onditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Stand Base Attached Detached O Power cord Wall outlet type or PC outlet type NOTE a Information in this document is subject to change without notice Specifications Display Sync Input Video Input Resolution Plug amp Play Power Consumption Dimensions amp Weight Tilt Range Power Input Environmental Conditions Stand Base Power cord NOTE 19 inch 19 inches 48 2 cm Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 48 2 cm 0 294 mm pixel pitch 30 83 kHz Automatic 56 75 Hz Automatic Horizontal Freq Vertical Freq Input Form Separate TTL SOG Sync On Green Signal Input 15 pin D Sub Connector Input Form RGB Analog 0 7 Vp p 75 ohm Max VESA 1280 x 1024 75 Hz Recommend VESA 1280 x 1024 60 Hz DDC 2B On Mode 36 W Typ Sleep Mode lt 1 W Off Mode lt 1 W With Stand Without Stand Width 40 63 cm 16 00 inches 40 63 cm 16 00 inches Height 41 97 cm 16 52 inches 34 45 cm
14. puter 1 Make sure to turn off the computer and product Connect the cable as below sketch map form to Connect Audio Cable Connect Dsub Cable PC Connect Dsub Cable Mac NOTE This is a simplified representation of the rear view m This rear view represents a general model your display may differ from the view as shown User must use shielded signal interface cables D sub 15 pin cable DVI cable with ferrite cores to maintain standard compliance for the product Power Cord Analog signal Audio signal AC IN D SUB AUDIOIN Q Wall outlet type Headphone Earphone Input Automatically mutes the speaker volume when the headphones are plugged in V PC uE g 1 PC outlet type PC q Ieo B pc a mA Hi gt Mac adapter For Apple Macintosh use a separate plug adapter is needed to change the 15 pin high density 3 row D sub VGA connector on the supplied cable to a 15 pin 2 row connector 2 Press l button on the front switch panel to turn the Fahy RTR power on When monitor power is turned on the IMAGE SETTING Self Image Setting Function is executed automatically NOTE Self Image Setting Function This function provides the user with optimal display settings When the user connects the monitor for the first time this function automatically adjusts the display to optimal settings for individual input signals AUTO SET Function
15. re hazard Call your service technician for replacement Do not Open the Display a here are no user serviceable components inside a here are Dangerous High Voltages inside even when the power is OFF a Contact your dealer if the display is not operating properly To Avoid Personal Injury a Do not place the display on a sloping shelf unless properly secured a Use only a stand recommended by the manufacturer Do not drop an object on or apply impact to the product Do not throw any toys or objects on the product screen It can cause injury to human problem to product and damage the display To Prevent Fire or Hazards a Always turn the display OFF if you leave the room for more than a short period of time Never leave the display ON when leaving the house Keep children from dropping or pushing objects into the display s cabinet openings Some internal parts carry hazardous voltages Do not add accessories that have not been designed for this display a When the display is to be left unattended for an extended period of time unplug it from the wall outlet a In the presence of thunder and lightning never touch the power cord and signal cable because It can be very dangerous It can cause electric shock Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord and do not place the display where the power cord is subject to damage Do not use this display near wa
16. rom the OSD m O Ww On Screen Display OSD Selection and Adjustment The following table indicates all the On Screen Display control adjustment and setting menus BRIGHTNESS PICTURE CONTRAST To adjust the brightness contrast and gamma of the screen GAMMA s PRESET 500K e 9300K RED RED Je HORIZONTAL To adjust the position of the VERTICAL screen ea To improve the clarity and stabilit io SHARPNESS OSD a FLATRON e To select or customize desired F ENGINE image settings NORMAL DEMO _ Adjustable A Analog Input 0 0 To customize the color of the screen 0000 000 To customize the screen status for a user s operating environment NOTE The order of icons may differ depending on the model A10 A15 On Screen Display OSD Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system Listed below are the icons icon names and icon descriptions of the all items shown on the Menu Press the MENU Button then the main menu of the OSD appears TRACKING SETVE Main Menu MENU 6 Exit Adjust Decrease Increase a SET 44 Enter Select another sub menu Restart to select sub menu Button Tip Menu Name picture MENUS 5 SET W n CONTRAST Sub menus Icons aE O GAMMA y Om 0 NOTE a OSD On Screen Display
17. s visible on the screen background The horizontal screen size will also change To adjust the focus of the display This item allows you to remove any horizontal noise and clear or sharpen the image of characters To adjust the clearness of the screen Main menu Sub menu SETUP LANGUAGE OSD OSD POSITION POSITION Soe B oo WHITE PE BALANCE MUTE ER FACTORY RESET On Screen Display OSD Selection and Adjustment Description To choose the language in which the control names are displayed To adjust position of the OSD window on the screen If the output of the video card is different the required specifications the color level may deteriorate due to video signal distortion Using this function the signal level is adjusted to fit into the standard output level of the video card in order to provide the optimal image Activate this function when white and black colors are present in the screen Use this function to set the speaker off or on Use this function to set the power indicator on the front side of the monitor to ON or OFF If you set OFF it will go off If you set ON at any time the power indicator will automatically be turned on Restore all factory default settings except LANGUAGE Press the W A buttons to reset immediately If this does not improve the screen image restore the factory default settings If necessary perform the wh
18. ter such as near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation If these openings are blocked built up heat can cause failures which may result in a fire hazard Therefore NEVER a Block the bottom ventilation slots by placing the display on a bed sofa rug etc a Place the display in a built in enclosure unless proper ventilation Is provided Cover the openings with cloth or other material Place the display near or over a radiator or heat source Main power breaker is the power cord and this breaking device must be located at a location where It is easy to operate Do not rub or strike the Active Matrix LCD with anything hard as this may scratch mar or damage the Active Matrix LCD permanently Do not press the LCD screen with your finger for a long time as this may cause some afterimages some dot defects may appear as Red Green or Blue spots on the screen However this will have no impact or effect on the display performance If possible use the recommended resolution to obtain the best image quality for your LCD display If used under any mode except the recommended resolution some scaled or processed images may appear on the screen However this is characteristic of the tixed resolution LCD panel Leaving a fixed image on the screen for a long time may cause dama
Download Pdf Manuals
Related Search