StarTech.com Dual Profile PCI Express to 34mm and 54mm ExpressCard Adapter Card
Contents
1. StarTech com Making hard to find easy PEX2ECDP User Manual Dual Profile PCI Express to ExpressCard Adapter Introduction Thank you for purchasing a StarTech com PCI Express to ExpressCard Adapter This product allows you to use an ExpressCard with your PCI Express enabled PC Features Supports both 34 and 54 form factor ExpressCards e Compliant with PCI Express Base Spec 1 0a e Works with PCI Express slots that provide 3 3V and 1 5V auxiliary power System Requirements e PC with an available PCI Express slot e Windows 2000 XP 2003 Server Package Contents e PCI Express to ExpressCard Adapter 1 e Low Profile Bracket 1 e 3 5 pin Header USB Cable 1 e User Manual 1 Hardware Installation Please note Please note Although PEX2ECDP supports both USB and PCI Express based ExpressCards only USB based cards offer hot swappable connectivity As such please consult the documentation that was included with your purchase of the intended ExpressCard to determine whether or not it supports hot swapping Make sure that your computer system is unplugged and that you are grounded 2 Remove the cover of your system see your computer s user manual for details if necessary and gently turn your computer onto its side so that the PCI Express expansion slot openings on the motherboard are facing upwards 3 Locate an empty PCI Express slot and remove the metal plate that covers the corresponding rear brac2. ket You may need a Phillips screwdriver to perform this step Retain the screw You will need it to secure the card later 4 Gently insert the card into the empty slot making sure it is firmly seated 5 Secure the card in place using the screw you removed in Step 3 D Connect the 5 pin header provided by PEX2ECDP to an available USB header on the host computer noting the following diagram Once complete replace the cover and power on the computer Signal USB USB USB Ground D D 5V Please note If the motherboard does not have a USB header available for connection please connect the USB Type B connector provided by PEX2ECDP to an available USB port connected to the mother board Failing this hot plugging will not be available for inserted cards Pin Headers PEX2ECDP offers several control status pins Label Signal Name Signal descriptio GND GND Signal ground CKE CLKEN Clock Enable oc OC Over current status SHD SHDN Shut down control input STB STANDBY Standby control input KRO CLKRQ H Clock Request from device CUB CPUSB USB device present status CPE CPPE PCI Express device present status LED Descriptions 1 Green D1 3 3 Vout fa d d d 2 Yellow D3 1 5 Vout 3 Green D2 Vaux 1 2 3 4 4 Specifications Red D4 Over current Please note 1 Signal denoted with indicates low active Slow down to Hi Z mode 2 All signals eithe
3. n or limitation of incidental or consequential damages If such laws apply the limitations or exclusions contained in this statement may not apply to you FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interfer ence to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the fol lowing measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Revision A October 11 2007
4. r have IC internal pull up or on board pull up Bus Type PCI Express Form Factor 34 and 54 ExpressCard Connectors 1 x 34 54 ExpressCard Slot 1 x Internal USB Type B Port 1 4 pin USB header Regulatory Certifications FCC CE ROHS Support Warranty Information and Regulatory Compliance Statement If you ever need help with your product visit www startech com sup port and access our comprehensive selection of online tools docu mentation and downloads This product is backed by a lifetime war ranty In addition StarTech com warrants its products against defects in materials and workmanship for the periods noted following the ini tial date of purchase During this period the products may be returned for repair or replacement with equivalent products at our discretion The warranty covers parts and labor costs only StarTech com does not warrant its products from defects or damages arising from misuse abuse alteration or normal wear and tear Limitation of Liability In no event shall the liability of StarTech com Ltd and StarTech com USA LLP or their officers directors employees or agents for any damages whether direct or indirect special puni tive incidental consequential or otherwise loss of profits loss of business or any pecuniary loss arising out of or related to the use of the product exceed the actual price paid for the product Some states do not allow the exclusio
Download Pdf Manuals
Related Search