Newstar KVM extender, UTP, USB
Contents
1. Emi yellow light with a bit of flash red if the Com pute Unit is taking control Users can easily identify this status from the keyboard in which 3 LEDs Num Caps and Scroll Lock onthe keyboard should be flashing Emit yellow light if the Computer Unitis on Auto mode the system is waiting for Console Unit or Computer Unit to take control Users can easily identify this status from the keyboard in which 3 LEDs Num Caps and Scroll Lock onthe keyboard are NOT flashing e The default status is set to Local ON when powering up e The Remote LED will flash long red light if the CATx cable disconnected Remote On Local Off Led Indicators Hum Caps Scroll Lock LEDs on Computer Unit Model LED Status Control Description Rx Data Receiving status Tx Rx Green Tx Data Transmitting status Flash Red Processing e Computer Unit controls its local PC or cascaded KVM Switches In this mode the Console Unit can not take control of the Computer Unit remotely Remote Off Local On Local unit Remote Local Flashes 9 The system is waiting for Console Unitor alternatively Auto Computer Unit to take control The control Mode priority is on the first come first served basis Local unit Remote On Local Off e Console Unit can remotely taking control of the Computer Unit e The default status is set to Auto when powering up e The Remote LED will flash red light if the CATx cable dis2. or to coarse tune 16 levels for adjustment 2 Press and Hdd Shift gB or to fine tune e Gain Brightness Caps Lock LED Scroll Lock LED Flashing 1 Press or to coarse tune 16 levels for skew 2 Press and Hdd Shift H or t to fine une B Blue Gl Green R Red 1 Press or to coarse tune 8 levels for adjustment Blue Green Red Color Adjustment LED Flasting Choose onecolor at 2 Press and Hdd Shift or to fine tune atime for adjustment Esd Escape from Video Adjustment Mode NOTE Users may press leading code Esc or just press Esc directly to escape from the video adjustment mode NOTES X Video Adjustment for Console Unit Only The video adjustment function is required to perform before configurations begin Please also make sure that all the system units and devices are connected propery before the video adjustment operation begin Users at the Console Unit can adjust the video signal compensating to various cable length through hotkey commands The video adjustment includes e Equalizer Sharpness e Gain Brightness Skew for the color blue green and red To compensate the lengths of CAT 5 CAT 5e CAT 6 cable there 16 levels on coarse tune and up to 128 256 scales on fine tune are available for adjustment on the equalizer and gain And there are 8 levels on coarse tune and 16 32 sca
3. Extender without additional connection to any KVM switch es and Compatibility Mode denotes the state of the KVM Extender with connection to KVM Switches 2 Leading Code denotes in Standard Mode the hotkey sequence left ore in Compatibility Mode the hotkey sequence left left El 3 BTN denotes Press and Hold the Push B utton in the to p pan elfor two second s 4 The hotkey state will be automatically time out if m There isno activity detected bythe keyboard within 6 seconds after Press and Hold the Push Butto ntwo seconds E Press the button once to escape from the hotkey mode E Press the Push Button once to escape fromthe hotkey mode and switch to either the Local or Remote mode 5 Bydefault the Video Synchronization setting between the Console Unit and Computer Unit will follow the C onsole Unit setting after reboot The following options for video resolution are available for selecting Input 4 digits with 1007 for resolution of 1024 xQ768 161 2 for resolution of 1600 x 1200 1307 for resolution of 1360 x 0768 141 0 for resolution of 1440 x 1050 191 0 for resolution of 1920 x 1080 1208 for resolution of 1280 x 0800 201 1 for resolution of 2048 x 1152 1210 for resolution of 1280 x 1024 1914 forresolution of 1920 x 1440 1409 forresolution of 1440 x0900 1610 forresolution of 1680 x 1050 191 2 forresolution of 1920 x 1200 1609 forresolution of 1600 x0900 23 Appendices Vid eo Adjustment for Console Unit
4. Folr3 ra F5 F6 F7 F8 ler lF12 1 2 3 4 5lel7 sfolo Hotkey Control For Computer Unit Commands Function Descriptions T Mode selection in sequence Switch console control between Local Computer and Remote Computer Alt S Reset the Unit to the factory default s Local mode selection J Enable the user at Computer Unit exclusive accessing to the PC KVM Switch that connects to Computer Unit Disable the Console Unit user accessing Remote mode selection Enable the user at Console Unit exclusive accessing to computer KVM Switch that 2 connects to the Computer Unit Only if the Computer Unit is in Remote o Auto mode Disable Computer Unit user accessing to the Computer Unit during this mode 3 Autoj Mode selection Latch time selection F3 Auto Mode latch time setting The extender generates 1 to 4 beeps to indicate the duration of latch ime 5 15 30 60 seconds respectively Fel Privacy setting enable disable Alternatively restrict the output video signal of Com puter Unit Not applicable for Button Maneuvering NOTES 1 Privacy Setting Enable Please identify the current mode in either Local or Auto mode by checking the Computer Unit LED first then through repeating the hotkey commands for privacy setting Leading Code Fa the KVM Extender generates 1 to 3 beeps to indicate the statuses of the Com puter Unit as follows A Computer Unit in Loc
5. Mouse USBA x 1 Console Side Monitor HDB15 Female x 1 Audio Jack 1 Set Speaker Mic Computer Unit Monitor HDB15 Female x 1 Grey Connectors USB PS 2 Interface Computer Side Audio Jack 1 Set Speaker Mic Remote Control Jack 38K x 1 for IR Receiver Front Panel LEDs each unit See LED Indicators Chapter Mask Hotkey Switch Push Button Control Status Selection Hotkey Control Yes Power Consumption Max External Power Adapter DC 9V 600mA Dimensions H xW x D mm each unit 22 x 140 x 100 20 Appendices Cable Requirements The cable Category 5 CAT5 terminated with RJ45 connectors is normally used for the interconnection between Computer Unit and Console Unit Its easy to get from the local stores or call your dealers for help Besides CAT5e or CAT6 are applicable to the KVM Extender This CAT5 cable is not provided in the standard package mainly because the cable length you required is subject to the deploying environment However the better the CATX cable quality the longer the video extension and the shorter the cable length the higher the video resolution CAT5 Cable The KVM Extender extends the remote access by using a piece of unshidded twisted pair UTP cable The cable must be wired in compliance with the EIA TIA 568B industry standard Note CAT5 CAT5e or CAT6 cables are applicable to the KVM Extender pair Pair 3 Above diagram
6. Only To enter the Video Adjustment Mode in Non Cascade Standard Structure Press left Ctrl eft Ctr F111 To enter the Video Adjustment Mode in Cascade Compatibility Structure Press left left E F11 While entering this mode the LED Number Lock and Scroll Lock are flashing simultane ously atthe moment Then users can perform the video adjustment by hotkey commands as the table shown below Be aware the idle time out is 30 seconds That is it will automatically escape from video adjustment mode if no action is detected by the keyboard within 30 seconds To exit the video adjustment mode three simplified approaches are available 1 No action is detected by the keyboard for 30 seconds 2 Push once the escape butto Esd onthe keyboard attached to the Console Unit 3 Push once the push button onthe top panel of the Console Unit Console Unit Hotkey Commands Function Descrption Equalizer Gain Adjustment e Equalizer Sharpness Num Loch LED Caps Loch LED Flashing 1 Press or gt to coarse tune there are 16 levels for adjusting 2 Press and Hold orp to fine tune e Gain Brightness Caps Lock LED LED Flashing 1 Press D or to coarse tune there are 16 levels for skew 2 Press and Hold Sh ift or to fine tune Appendices Computer Unit Hotkey Control Computer Unit Hotkey Commands Mask Hotkey OFF Mask H otkey ON Alternative Alternative Hotkey Hotkey Hotkey F
7. cable for the connection between the video port on the console side of the Unit and the video port of the connected monitor Plug a USB keyboard and a USB mouse into the respective icon marked USB ports on the console side of the Unit a If needed plug a set of audio jack from speaker and microphone into the Unit s speaker port and microphone port respectively Installation Power Connection a After all device connections are completed connect the provided power cord into an appropriate power source and plug the opposite end into the power connector on the Unit to power up the system FG or STA Saatchi Led Indicators The LEDs on the KVM Extender show the real time status indicating the linking communication and control between the Computer Unit and Console Unit Users can switch control through the push button and identify the present status through the LED indicator on the top panel as the following lists 1 Press the push button on Console Unit to select Local On or Remote On 7 ck 2 Press the push button on Computer Unit to select Local On Remote On or Auto Mode Remote Remote LEDs on Console Unit LED Status Control Description Rx Data Receiving status Tx Rx Green Flash Red Processing Tx Data Transmitting status Console Unit is enabled to access to the Computer Unit and the remote LED will Emit yellow light if the Console Unit is taking control
8. setting enable is Alte ma tively restrict the output video signal of Com puter Unit a BTN F6 BTN Leading C ode F z ah 2 Sec Ed Blue Color Adju stment Scroll Lock LED Flashing 1 Press or to coarse tune there are 8 levels for adjusting 2 Press and Hold Shiff f or gt to fine tune Red Color Adjustment LED Flashing 1 Press or gt to coarse tune there are 8 levels for adjusting 2 Press and Hold Sh ifd or gt to fine tune Leading Code V BTN v BTN V input4 digits with 1007 for resolution of 1024 x 0768 ESC N Escape from Video Adjustment Mode NOTES Make sure to connect the unit and devices properly before the video adjustment The video adjustment function is available on the Console Unit ONLY 3 An alternative hotkey approach to enter Video Adjustment mode is available for users to choose as desire in which users can simply press the top panel push button followed by input the key F114 For more detailed information please refer to the section Hotkey Commands and Alternative Hotkey Control 24 Leading Code F12 BTN E14 2 Sec Mouse resynchronized for PS 2 model only Video synchronization Prevent the video resolution setting from exceed ing the capability of the connected display require CPU reboot the following options of video resolution are availa
9. to the Extender Unit as if you are virtually sitting in front of the KVM Switch The interface compatibility and flexibility can be simply enhanced by choosing custom made KVM cable s for your existing PS 2 or USB computer s It provides advanced features including dual user access LED indicators for real time status monitoring serial interface for serial equipments and data communications audio jack speaker Mic for audio display With the small footprint the Extender can be easily installed and deliver the high definition signal over long distance which is a perfect solution for factories or construction areas where you want to secure your computers and valuable data or manage them both in remote and local sites The Extender Unit can be connected with 1 to 3 or 1 to 2 cable s as the following figure shown For details please proceed to the section Specifica tions Connection of 1 to 3 and 1 to 2 cable m Remotely locate the keyboard mouse and monitor up to 200 meters away from a computer m Support high video resolution up to 1920 x 1200 WUXGA m Support USB console m Ability to extend IR control m Support the HID standard keys m Equalizer sharpness gain brightness adjustment via hotkeys for optimal video quality m Unique RGB skew adjustment via hotkeys for the best video quality m Synchronize the video resolution via hotkeys m EDID Emulation function makes the best resolution for your application m
10. Easily expand the multiple computer controls by cascading KVM Switch es m Hotkey functions and push button for easy computer access m Mask Hotkey function enable the direct control in cascading Compatible with all PS 2 or USB computers by using 1 to 3 PS 2 interface or 1 to 2 USB interface KVM cable s m LED indication makes operation user friendly m Locate the computer away from your desk and work area saving you valuable space m Allow two users to share computer s both in local and remote areas m Beep confirmation for hotkey control makes the operation easier and cross checked Compatible with most of the popular screen resolution to XGA SXGA UXGA WSXGA WUXGA system m Serial communication function optional 1 Fully compatible with all RS 232 protocols allowing full range of baud rates to be used 2 Full Duplex data communication Real Time pure hardware solution 4 Extend serial transmission up to 115 200 bps maximum a Packing Checklist KVM Extender Console Unit x1 KVM Extender Computer Unit Power Adapter with necessary AC Cord or Plug in Power Adapter CD with User s Manual Quick Start Guide Foot Pad Set Ground Wire KVM Cable Audio Cable for Computer PC Side Optional IR External Sensor Transceiver Receiver Kit O O op 1 External Sensor 2 Multi mode Stand 3 Metal Plate 4 Screws T Transceiver Receiver 3 System Requirements S
11. INSTRUCTION MANUAL DC 9 12V v AJS Hora Computer eler NSS560UTP USB U g a Remote CAT5 Full HD NS560UTP USB NS560UTP USB Table of contents Introdu CH QIN ra jr narr Ao a Ar ARN RN HRN NE HEN R RN RAR 1 INET E birds setts aoe ee TEE ere E nee nee eee eer ere 1 Fe SS E E E E passen on E EE E AE T E A EE E E 2 PACKING COCKS I erae ns E A O OR 3 System Requirements m ssmssmnrsessrosrror esse rrnsr rr sr rr sr rr sr KRK RR KKR RAR RR rn nl 4 bde TRAE e E E E E E EAT E N E NER 4 Product DesCriptiOlN ssssssmrssssrsrasrssrrrorn rara nen ax anne sr rn sn rr KBR RR RER RAR RR KR RR KKR ROR KKR Rn 5 MSto 225 surstossustotasst brinsanst noes A AO AAE 6 C mecton P ALC TINS ecean a OEA 8 LED INOICA TOS rinn E A onan caution 10 Hotkey Launch n e nnennnenenesonanrennrennurnnrenrnursrrrnrursrnsnrnnsrronrnnerrrenn ereenn 12 Button Maneuvering amp Control COMMANAS cccccseeceeeea aranna 13 For Console and Computer Units smsssmssmrrrsrrserssrrnrrrrr anna arsa anar 13 For Computer Unit c cc ccccecceee esse seeeeseeeeeeeaueeaneesseseaneeateeans 14 FOr Console UNI Renee ner P nC eet vent nee nN tee ene tee eee rere 15 TroublesShO OtiNOs ssnnesnnreerersrorere ren rrnsrersrnrnreronrrrsr reser ror rr ere nere rn R Orre ker neon 18 BS of 64 1 C67 11 Ce kee ee nee ee Nesse 20 APDENOICES ass eh ma nee ee ee ee nt eee nee ne 21 ys Please read this manual thoroughly and follow
12. al mode Remote LED Off Local LED On e One beep Enable the output video signal of Com puter Unit e Two or three beeps Disable the output video signal of Computer Unit B Computer Unit in Auto mode Remote Local LED flashes altematively e One beep Enable the output video signal of Computer Unit e Two beeps By triggering keyboard mouse users can disable the output video signal of Computer Unit temporanly The Computer Unit users protect the privacy for 5 15 30 and 60 seconds See the above table Latch time selection for more descriptions e Three beeps By triggering keyboard mouse the Console Unit or Computer Unit users can temporarily disable the output video signal of the other Unit Users protect privacy for 5 15 30 and 60 seconds as well Letu esting Lewis tal i F adru Dalaj Pa a aa T Aa ia f Isar af Lici Uni dainai Boones conirel Bese Ono based on Fred coma iral emd Local Mods of Siler ker 14 Local Unit Hotkey Control For Console Unit Part 1 Video Adjustment The Video Adjustment function is on Console Unit only To launch its hotkey command also start with the specific leading code or BTN 2sec and then press to enter Video Adjustment Mode After adjustment just press Esc to escape from hotkey mode Commands Function Descriptions Video Adjustment Equalizer Gain Adjustment e Equalizer Sh arp ness Num Lock LED Caps Lock LED Flashing 1 Press K
13. ard is eligible for hotkey commands The Compatibility Mode Users can configure the computer attached to the KVM Switch by applying the KVM Extender built in hotkey command prefixed with the cascade leading code eft Ctrl left Ctrl E The state of the KVM Extender with or without connection s to KVM Switch es Users can apply built in hotkey commands of its KVM Switch es or use the KVM Extender alternative hotkey command with the YES NO button maneuvering Press amp Hold push button 2 sec the LEDs blink orange and then followed by one or two more keystrokes within 6 seconds In later descriptions this action will be simplified as BTN 2sec Notice The hotkey command will be automatically time out if E There is no activity detected by the keyboard within 3 seconds after the leading code input when Mask Hotkey OFF or within 6 seconds after BTN 2sec when Mask Hotkey ON E Press the button once to escape from the hotkey mode E Press the Push Button once to escape fromthe hotkey mode and switch to eitherthe Local or Remote mode Hotkey Control Before inserting commands below for respective functionality its required to launch the specific leading code or press the push button for 2 seconds and then succeed by one or two more keystrokes commands as the following charts show For Console and Computer Units Commands Function Descriptions Cascading status selection both Units ne beep E
14. ble for selecting Adigits Adi gits 2 Sec Adigits 2 Sec 1210 for reso lution of 1280 x 1024 1612 for resolution of 1600 x 1200 1912 for resolution of 1920 x 1200 1914 for resolution of 1920 x 1440 201 1 forresolution of 2048 x 1152 NOTES Standard Mode denotes the state of the KVM Extender without additional connection to any KVM switch es and Compatibility Mode denotes the state of the KVM Exte nder with connection to KVM Switch es Leading Code denotes in Standard Mode the hotkey sequence eft Ctrl left in Compatibility Mode the hotkey sequence left left Ctrl E BTN denotes Pres s and Hold the Pus hB utton on the top panel for two seconds After Press and Hold the Push Button two seconds the hotkey state will be au to matically ti me o ut if E There is no activity detected by the keyboard within 6 seconds E Press the button Esc once to escape from the hotkey state E Press the Push Button once to escape from the hotkey state and switch to the Auto Local or Re mote mode
15. connected 1 Remote Control applied 1 Remote Contrd enabled 2 CATx linking Status 2 CATX linking Status 11 Hotkey Control A hotkey command is a short key sequence to select a computer activate computer scan and so forth The KVM Extender interprets keystrokes for hotkeys all the time And the built in buzzer generates a high pitched beep for correct hotkey command otherwise one short and one long beep are generated for a bad command in which the bad key command won t be sent to the extender unit or the selected computer Cascade Architecture The KVM Extender can be connected to the KVM Switch in compliance with the Cascade Configuration However to prevent from any conflict via hotkey commands in the cascade configuration the hotkey commands prefixed with Compatibility mode leading code which can be applied for directly accessing to the KVM Extender Mask Hotkey Switch The hotkey commands of KVM Switches vary among models which may cause hotkey errors unwanted configurations between the Extender Unit and mixed types of KVM Switches that connect to each other The Mask Hotkey extremely simplifies the hotkey control in cascade architecture Mask Hotkey Hotkey Commands Switch Cascade Arch itec ture The Standard Mode factory default The hotkey command starts with the leading code eft Ctrl left Ctrl followed by one or two more keystrokes Only the key Ctrl located on the ower4eft corner of the keybo
16. factory default Escape from hotkey mode Mode sek ction in Sequence switch console c ontrol between Local Computer and Remote Computer Leading C ode l Leading C ode 4 Local mode selection enable th e user at the Console Unit accessing tothe computer KVM Switch that conne ds tothe Console Unit Rem ote mode selection enable the user at the Console Unit exclusive accessing to computer KVM Switch that connects to the Computer Unit only if the C om puter U nit is in Remote or Auto mode Disable Computer Unit user accessing to the Computer Unit during this mode Lea ding Code BIN E14 2 Sec Leading Code Pe F14 Leading Code M BTN M 4 digits Adigits 2 Sec BTN F11 Video adjustment entrance More video quality setting can be found here Mouse resy nc hronized for PS 2 model only Prevent the video resolution setting from exce edi ng the capability of the connected display require CPU reboot the following options for video resolution are 2 Sec BTN F12 2 Sec Video synchronization BTN V available for sele ct ng Adigits 2 Sec Input 4 digits with 1007 for resolution of 1024 x 0768 1210 for resolution of 1280 x 1024 161 2 for resolution of 1600 x 1200 191 2 for resolution of 1920 x 1200 191 4 for resolution of 1920 x 1440 201 1 for resolution of 2048 x 1152 NOTES 1 Standard Mode denotes the state of the KVM
17. her monitor Action No video signal Use the EIA TIA 568B industry standard CATx cable for KVM Extender connection Unplug the CATx cable s from the Extender then plug it them back in Perform the video quality adjustment for the length of CATx being used Poor video quality Keyboard hotkeys are inoperable when the KVM Extender comnects with the KVM Switch Apply compatibility mode hotkey commands Verify if the Extender has enough power Remove and reinstall each device checking the connectors and sockets for bent pins or other damage Problems continue to occur after checking the solutions above Ensure that the keyboard connectors that are Can t insert hotkey commands correctly connected to the port Set the Mask Hotkey to OFF factory default Check the cable connected between PC and the Console Unit Insert the hotkey Ctrl Ctrl F6 with one beep to reset to factory default The mouse gets inactive for a while 18 19 200M KVM Extender Series UXGA 1600 x 1200 Video Resolution Max WUXGA 4 920 x 1200 Extension Distance 200M Unit Connection CAT5 RJ45 Female Keyboard USB A x 1 Mouse USB A x 1 Console Side Monitor HDB15 Female x 1 Audio Jack Speaker Mic eee Console Unit Monitor HDB15 Female x 1 Grey Connectors USB PS 2 Interface Computer Side Teale a E Speaker Mic Remote Control Jack 38K Mask Hotkey Switch Keyboard USB A x 1
18. is it will automatically i f escape from video adjustment status if no activity is detected by the keyboard within 30 Fi i seconds 7 NN Jf F To exit the video adjustment status three approaches are available r SL E a s 1 No activity is detected by the keyboard for 30 seconds Ree Color Ad ue 2 Push once the key Esd on the keyboard attached to the Console Unit a ave 3 Push once the push button onthe top panel of the Console Unit me EF SL Press Esc to Escape ee es RR ca m from hokey made Gain EQ Adj Press or to adjust the Equalizer setting Press or to adjust the Gain setting Red Gree n Blue Color Adj Press or to adjust the RGB correction Troubleshooting Troubleshooting If you encounter problems with the NewStar KVM Extender during the installation or operations please check through this section for a possible solution If your problem is not listed here and you can not resolve the issue please contact your local dealer for the fastest assistances Verify that all the cables are qualified according to the hardware requirement section Verify that all the cables are properly connected to their ports and are firmly seated Use an alternative CATx cable connection between the unit of console and computer Power down the computer Connect the monitor directly to the computer and power up again If the monitor does not operate correctly direct to the computer try anot
19. k Connect to PC s audio port L6 RJ 45 Jack Use CAT5 cable for the extender connection L7 HR Control Jack Plug the external sensor Receiver here L8 Ground System grounding NOTE For details about LEDs please refer to LED Indicators chapter Installation Grounding To prevent any damage to the product or any connected device it is important to make sure that both the monitor and or computer connected to the Unit and the KVM Extender are properly grounded arddio Cautions 1 Prior to the installation ensure that all devices to be connected to this system are powered off and grounded 2 Place cables away from fluorescent lights air conditioners and machines that are likely to generate electrical nose 1 to 3 cable PS 2 connection 1 to 2 cable USB connecton Installation Connection Patterns The installation is as easy as dynamically connecting the computer to the Local Unit and or Remote Unit and connecting the Local Unit to the Remote Unit with the appropriate CAT5 cable Please follow the guidelines below for the system connection a Use KVM 1 to 3 PS 2 interface or 1 to 2 USB interface cable for the connection between the video port on the computer side of the Extender and the video output port amp KB MS port of the connected Computer a f needed use a set of audio cable to connect the speaker port microphone port between the Extender and Computer PC or EWH Jaic Use VGA
20. les on fine tune are available for skew adjustment on blue green and red 15 Hotkey Control Hotkey Control Hum Cans Scroll Lock File Edt View Favorites Tools Help gt gt P Puh Folders Tri Address 1 My Computer Files Stored on This Computer 0 net Shared Documents J clent s Documents Hard Disk Drives ke My Network Places My Documents Shared Documents x E E HE G Control Panel Ga Enss C FP sso NU Devices with Removable Storage Before Video Adjustment l H 3 Floppy A CD RW Drive F After Video Adjustment Notice 1 The video adjustment is available on the Console Unit ONLY 2 The video adjustment is applicable only if the CATx cable is connected and the Console S a e SERNER ar vg Unit is remotely taking c ontrol of Computer Unit AL Bia Golor Adj i Users can activate video adjustment on Console Unit either through hotkeys or push button Pid fr SE act The Unit is capable of hotkey control whether the Mask Hotkey is OFF r i N 4 While the Video Adjustment is activated the LED Numeric Lock and Scroll Lock on the J 2 keyboard connected to the Console Unit will flash simultaneously at the moment Then users r i can perfom the video adjustment by hotkey commands as the table shown below beading Code t Gun Po Agr i Graan Color AS I Be aware The idle time out of Video Adjustment is 30 seconds That
21. nable Standard Mode Console Unit Alt E wo beeps Enable Compatibility Mode and the userat Console Unit accessing to the KVM Switch that is media to Computer Unit Computer Unit Enable Compat bility Mode and the users at Computer Unit accessing to the KVM switch that is comecting to the Computer Unit Esc Escape from hotkey mode F12 Mouse resynchronized for PS 2 PC EDID Config uration EDID Emulation Prevent the video resolution setting from exceeding the capability of the connected display requre CPU reboot the fdlowng options for video resdutio are available for selecting Input 4 digts with 1007 for resolution of 1024 x 0768 7 1210 for resolution of 1280 x 1024 4 digits 1612for resolution of 1600 x 1200 1912 for resolution of 1920 x 1200 1914 for resolution of 1920 x 1440 2011 for resolution of 2048 x 1152 Not applicable for Button Maneuvering NOTES By default the EDID Configuration EDID Emulation setting between the Console Unit and Com puter Unit will follow the Console Unit setting after reboot The following options for video resolution are available for selecting 4 digits Resolution 4 digits Resolution 10 07 1024 x 768 16 12 1600 x 1200 12 08 1280 x 800 1680 x 1050 12 10 1280 x 1024 1920 x 1080 13 07 1360 x 768 1920 x 1200 14 09 1440 x 900 1920 x 1440 14 10 1440 x 1050 2048 x 1152 16 09 1600 x 900 Esc 1
22. shows the RJ45 connector of a CAT5 cable with its metal contacts facing up 21 Warranty IN NO EVENT SHALL THE DIRECT VENDOR S LIABILITY FOR DIRECT OR INDIRECT SPECIAL INCIDENTIAL OR CONSEQUENTIAL DAMAGES LOSS OF PROFIT LOSS OF BUSINESS OR FINANCIAL LOSS WHICH MAY BE CAUSED BY THE USE OF THE PRODUCT EXCEEDS THE PRICE PAID FOR THE PRODUCT The direct vendor makes no warranty or representation expressed or implied with respect to the contents or use of this documentation and especially disclaims its quality performance merchantability or fitness for any particular purpose The direct vendor also reserves the right to revise or update the product or documentation without obligation to notify any user of such revisions or updates For further information please contact your direct vendor All the brand names and registered trademarks are the property of their respective owners 22 Appendices Console Unit Hotkey Control Console Unit Hotkey Com mands Mask Hotke y OFF Alternative Hotkey Hotkey Mask Hotkey ON Hotkey Alternative Hotkey Function Description ctr ctr f lAlt S Lea ding Code Esc Leading Code T Cascading status selection One beep enable Standard Mode factory de fault Two beeps enable Compa t bility Mode and the user at Console Unit accessing to the KVM switch that is connecting to Computer Unit Res et the Console Unit to the
23. the Installation procedures to prevent any damage to the unit or any connecting device x To prevent damages to your installation it is important that all devices are properly grounded FE CE va Rons Introduction Overview KVM Extender consists of a Console Unit and a Computer Unit allowing you to extend the keyboard monitor mouse console up to 200 meters away from a source computer or KVM Switch by using an inexpensive Category 5 5e 6 UTP unshielded twisted pair cable The Extender supports high video resolution up to Full HD 1920 x 1080 WUXGA 1920 x 1200 1920 x 1440 Through the easy hotkey commands you can conveniently adjust the video quality to compensate the cable lengths and synchronize the optimal video resolution between the attached computers such as equalizer sharpness gain brightness and zero the skew delay for green blue and red It is economical and scalable design for growth oriented enterprises which you can easily expand the multiple computer controls by adding additional Extender s or cascading the Extender s with KVM Switch es whenever you need The dedicated Hotkey Mask feature eliminates all the hotkey control barriers caused by mixed combinations of KVM Switch es in cascading environments The Extender can mask up itself through the hotkey mask enabling you to bypass the cascaded Extender level and directly configure the cascaded KVM Switch by using the keyboard mouse that connect
24. unction Description Hotkey Cascading status selec tion One beep enable Standard Mode Iwo beeps enable Compatibility Mode and the users at Computer Unit access ngto the KVM switch that connects to the Computer U nit C trl Ctrl att e Ctrl Ctrl ait S Reset the Computer Unitto the factory default Leading Code Es q Escape from hotkey mode Modeselection in sequence Toggle switch to select Auto Local On or mode Local mode selection enablethe user at Computer Unit exclusive accessing to the PC KVM Switch that connects to C omputer Unit Leading Code Leading Code Disables the Console Unit user accessing Remote mode selection enable the user at Cons ole Unit exclusive accessing to the PC KVM Switch that connects to Computer Unit Disables the user at the Com puter U nit accessing to the connected KVM Switch mode selection Leading Code 2 Leading Code Green Color Adjustment Caps Lock LED Flashing 1 Press or gt _ to coarse tune there are 8 levels for adjusting 2 Press and Hold Shift or B to fine tune Latch time selection BTN F3 Autd mode latch time setting the extender generates 1 2 Sec 2 Sec to 4 beeps to indicate the duration of latch time 5 15 30 60 seconds respective ly Leading Code F3 Privacy
25. ystem Requirements 1 Computer s with USB port s or PS 2 port s 2 USB keyboard mouse for console controlling 3 Suitable ground object for system grounding You will need 1 VGA Cable amp Audio Cable 2 Category 5 5e 6 UTP cable EIA TIA 568B industry standard compliant in accordance with length limits for optimum signal integrity Product Description Console Remote R6 RS R3 R2R4R1 R7 R8 a R1 Video Connector Connect to the monitor O IR2 Connect to the mouse A USB Connectors o IR3 Connect to the keyboard P R4 Audio Jack Connect to Speakers and MIC O O OFF right Standard mode MN V sk Hokey Switch ON left Disable the Extender hotkey function R6 RJ 45 Jack Use CAT5 cable for the extender connection R7 HR Control Jack Plug the external sensor Transceiver here R8 Ground System grounding NOTE For details about LEDs please refer to LED Indicators chapter Product description Computer Local Unit L L2 DC in LI L10 jab Kvii Goes ae EXTERHDOE L3L4L1 L7 L8 a L1 Video Connector Connect to the monitor L2 Connect to the mouse A USB Connectors o L3 Connect to the keyboard D L4 Audio Jack Connect to Speakers and MIC 2 OFF right Standard mode LS Mask Hotkey Switch ON left Disable the Extender hotkey function L9 Computer Connection Use KVM cable for PC connection OD Y L10 Audio Jac
Download Pdf Manuals
Related Search