"Splendide 2100" WD2100
Contents
1. flushed into the machine during the wash cycle NOTE From time to time you may see water in the dispenser compartments This is a result of the siphoning action and is part of the normal operation of the washer 10 Using too much detergent and softener causes over sudsing and poor rinsing and will harm the efficiency of your machine Only use detergents that are suitable for washing machines j IMPORTANT Do not exceed the recommended amounts p Helpful Hints Before adding detergent for pre washing in the Pre wash compartment 1 make sure that the extra compartment for bleach has not been inserted Do not use liquid detergent in the pre wash compartment The pre wash compartment only accepts powder detergent When you use fabric softener the washing machine automatically dispenses the softener to the last rinse of your selected wash program When using liquid detergent pour the detergent into compart ment 2 just a few seconds before starting the wash cycle Never use hand washing detergent because it may form too much foam and could damage your machine When washing with cold water reduce the amount of detergent you use it dissolves less easily in cold water than in hot water so part of it would be wasted iUsing Bleach If bleaching is necessary the extra compartment 4 must be inserted into the Pre wash compartment 1 Fig 10 e Be careful not to exceed the max level indicated on the central pivot2. Select the program according to the type of garments you are washing Refer to the Guide to the Wash Programs chart on p 7 then e Turn the Program Selector knob A clockwise until the selected program is aligned with the mark on the knob e Turn the Wash Temp knob C to the desired wash temperature for your load e f necessary use buttons E F G or H to run a Special Program If you do not wish to use these buttons leave them in their OFF OUT position e Lastly press the On Off button 1 in The Status Door Lock lamp L will flash slowly for 5 seconds then will light steady to indicate that the program has been accepted NOTE Should you wish to interrupt a program in progress or set a new one advance the Program Selector knob A to a Reset position and wait 5 seconds Pilot lamp L will flash slowly then turn the appliance off At the end of the wash cycle e The Status Door Lock lamp L will flash quickly for up to 1 2 min to indicate that the cycle is finished but the door is still locked The light will flash slowly when the door can safely be opened e When the Status Door Lock lamp L light flashes slowly turn the washer dryer OFF by pressing the On Off button I again Open the washer dryer door and remove your freshly cleaned laundry e After removing your laundry leave the door open to allow for air circulation inside the drum to avoid the formation of bad odors 14 Helpful Hints To
3. Use more if water is extremely hard use less in soft water recommended amount of liquid fabric softener Doing so could impair wash results and cause damage to the internal parts of your machine f IMPORTANT Never use softener sheets or exceed the B Bleach Cotton Heavy Duty Cycles Only Use bleach to whiten remove certain problem stains deodorize and even sanitize fabrics bleach dispenser Excess bleach could damage clothes h WARNING Always dilute bleach before using Never overfill Bleach should never be added to rinse water Getting Started Understanding Fabric Care Labels Garment labels contain washing drying instructions expressed in small symbols Learn the symbols on this table they ll help you to obtain better wash results treat your clothes properly and get a better performance from your machine ing wash r7 t f 4 LA Normal Permanent Press Delicate Hand wash Do not wash Do not wring Cotton Heavy Duty wrinkle resistant Gentle Hot Warm Cold Cool 50 C 120 F 40 C 105 F 30 C 85 F eee O O Q x Normal Permt Press Delicate Do not Do nat dry Cotton Heavy Duty wrinkle resistant Gentle tumble dry Special 7 Instructions M Mm Y Line dry Drip dry Dry flat In the shade Look Always check the hang to dry labels on your clothing They will help you select the right Bleach Al IN A wash program temperature Symbols laundry aids and more Water Temp Any bleach Only non c
4. space The performance levels safety features sturdiness and all its functions are the result of ongoing technological innovation The ultimate purpose To offer you the best performance with the utmost simplicity W Read This Manual Inside this book you will find many helpful hints on how to install use and maintain your new washer dryer properly Please read this manual carefully Just a little preventative care on your part can save you a great deal of time and money over the life of your washer dryer If you need further assistance please contact Splendide Laundry Centers at 1 800 356 0766 EW For Your Records Write model and serial numbers here You can find them on the front of the machine and inside of the door opening Model Serial A A CAUTION To reduce the risk of electric shock DO NOT remove cover or back No user servicable parts inside Refer servicing to qualified services personnel CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol with in an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the
5. Fig 11 e Always dilute the bleach with water before using e Traditional bleach should only be used on sturdy white fabrics therefore the bleach option is only available when using a Cotton Heavy Duty cycle NOTES the use of the additional bleach compartment excludes the possibility of using the Pre wash button When using Bleach it is recommended that you press the Extra rinse button Detergent Dispenser Cleansing Occasionally detergent build up may accumulate in and or around your dispenser drawer The detergent dispenser can easily be removed and cleaned e Pull it outwards Fig 11b e Leave it under running water a few minutes to remove the build up Inspect and wipe out dispenser alcove if necessary Replace the dispenser drawer 13 Operation Instructions How to Wash iStarting Your Washer Dryer Starting your washer dryer in the right way effects the quality of your wash results will help prevent future problems and will enhance the life expectancy of your machine Once you have loaded your washer dryer correctly see Choosing a Load p 12 and added detergent and fabric softener see About Laundry Aids on p 10 always check that e The door is closed correctly e The plug is secured in the socket The water supply is turned on e The Program Selector Knob A is positioned on one of the Reset positions e The On Off button I is in the OFF position How to Wash Only
6. Side View WARNING To reduce the risk of fire NN this appliance MUST BE EXHAUSTED OUTDOOR celi cei lo e Additional clearances for wall door floor moldings may be required 4 i im di 1 Kk As an Energy Star Partner Splendide Division Thi lian tested by UL and M Westland Sales has determined that Energy Star U i Mi i are a ir i nm S UL EA labeled models meet the Energy Star guidelines for C O ei EET m ues energy efficiency safety requirements and displays their mark Installation Instructions GROUNDING INSTRUCTIONS This appliance must be grounded In the event of malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for electric current This appliance is equipped with a cord having an equipment grounding conductor and grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances DO NOT modify the plug provided with the appliance If it will not fit the outlet have a proper outlet installed by a qualified electrician grounding conductor can result in a risk of electric shock Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded j WARNING Improper connection of the equipment N Attention N For your own protection and to prevent accidents injury and fire please re
7. base of the machine No more than 6 of the drain hose should be inserted into the drain pipe to prevent m7 Installing Exhaust Ducting Rigid or flex metal metallic ducting should be used Exhaust ducts should be as short and straight as possible and slope downwards and away from the machine NOTE Long exhaust siphoning l se e Use a strap cable tie or similar item to hold the hose or the U Clamp in ducting can extend drying time collect lint and may effect place drying performance Before Using Your Washer Dryer The exhaust duct must end with an approved exhaust vent hood with e Read manual thoroughly Keep these instructions for future reference swing out damper s or tailpiece with louvers e Run the empty washer dryer through a complete wash cycle to checkfor Check that all ducting is clean and lint free Use duct tape or screw water leaks and proper operation clamps to secure all joints e Wipe the inside and outside of the appliance with a damp cloth to remove Use duct tape or screw clamps to secure the duct to the round flange any dustthat has accumulated during transit vent located on the back of the machine see fig on page 3 Introduction Congratulations Thank you for choosing Splendide North America s 1 selling combination laundry center since 1984 Your new Splendide washer dryer is designed to give you maximum washing and drying performance while using less energy resources and taking up less
8. eliminate worry about selecting the right water level your washer has a sensor water level control system that is designed to ensure the correct amount of water is pumped into the machine for any load size Use one of the Express wash cycles to wash smaller loads of your lightly soiled Cotton Heavy Duty or Permanent Press fabrics in less time About the Easy Iron button This special program uses specifi cally studied wash motions to respect fabrics in the best possible way During the rinse phase it introduces more water and the spin cycle is shorter with a reduced spin speed thus producing more outstreched fabrics for easier ironing see Understanding the Control Panel pg 9 for complete instructions i Setting Delay Start Use the Delay Start option on your washer dryer to delay the start of any wash program by 12 9 3 or 1 hour s e With the machine power OFF turn the Program Selector Knob A clockwise to one of the 4 delay start positions 12 9 3 or 1 hr e Press the On Off button I The Status Door Lock lamp L will flash slowly for 5 seconds and then stays lit to indicate that the delay time has been accepted Now you can turn the knob clockwise to the program you desire e The Status Door Lock lamp L has a particular flashing motion 2 seconds on and 4 seconds off to indicate that a delayed start has been set During this phase you can open the appliance door and change the washing load should you wish to
9. faucet using a Faucet Adapter Kit available separately It will supply water from your faucet and discharge water directly into your sink drain m5 Leveling e To access the front leveling legs tilt the machine backwards leaning it against a wall or other stable structure Sink Drain W Y Branch Tailpiece Laundry Sink Drain Adjust the legs up or down Fig 8 to s ensure the washer is resting solid and does not rock side to side or front to back when the machine is upright e Check that the angle of inclination 25 62 cm min with an air break measured according to the worktop does not exceed 2 N IMPORTANT The machine must rest solid on a sturdy floor for optimum performance and minimum vibration IMPORTANT Make sure that the drain hose is not kinked NN and that water flow is not restricted m6 Electrical Connection e Plug the power cord into a grounded outlet See Grounding e Use a U Clamp provided in your accessories packet or suitable item to Instructions p 2 for complete details NOTE Check to ensure the secure the outlet end of the drain hose pre installed on the back of your power is OFF at a circuit breaker fuse box before plugging the power machine cord into the outlet Turn power on at the circuit breaker fuse box e Insert the outlet end of the drain hose into the standpipe wall or floor drain Fig 6 NOTE The outlet end of the drain hose MUST be at least 20 50 cm above the
10. interrupt a program in knob A to a Reset position and wait 5 seconds m Dry Time Knob B Use this knob to set the drying time up to 120 minutes Once set this knob will not move NOTE The last 12 minutes of the dry cycle is a cool down period See Dryer Cool Down p 7 Water Temperature Knob C Use this knob to set your wash water temperature Choose between HOT WARM COLD or variations between NOTE Rinse water temperatures are always COLD m Dispenser Drawer D This is where you add your detergent and other laundry aids See How to Use the Dispenser Drawer p 13 BPre wash Button E For heavily soiled loads push this button to add an extra wash to any wash program except the Wool program or when another Special Program F G H is selected WEasy Iron Button Rinse Hold F Pressing this button prevents fabric creasing making items easier to iron Only available on Permanent Press cycles and the Silk cycle If pressed the wash cycle will come to a complete stop Rinse Hold at the Anti crease part of the dial allowing you to leave items in the machine without spinning to prevent wrinkling You complete it by pressing the Easy Iron button again NOTE If a dry cycle is preset machine will not perform the anti crease rinse hold function SUPER REGULAR iy EXPRESS COTTON HEAVY DUTY Delay Start Rinse Spin RY a Reset g Reset The Knob A with your REGU
11. last rinse Spin cycle 850 RPM spin Draining and spin cycle Drying cycle for synthetic fabrics Permanent Press Dry Program Reset Interrupts cancels program Delicat P 16 min wash cycle 3 rinse cycles NN Regular e e anti crease or spin cycle Silk and particularly delicate garments Q PE 17 min wash cycle 3 rinse cycles Curtains silk viscose etc Silk i id and draining no spin cycle Wool hand h 27 min wash cycle 2 rinse cycles Aa Wool j j anti crease or spin cycle Rinse cycles Softener is automatically Rinse cycles anti crease or draining dispensed during the last rinse or spin cycle Spin cycle 600 RPM spin Draining and spin cycle Draining Draining Only Silk program Drying cycle for synthetic fabrics Delicates Dry Program Reset Interrupts cancels program Delay Start 12 9 3 1 hour delay Program start is delayed Stop Reset Interrupts Cancels program Easy Iron Description Wash Only Reduced agitation rinse spin speed and Anti crease Rinse Hold Wash to Dry Reduced agitation rinse and dry temp No Anti crease function Note Above cycle times vary according to water pressure load size and fabric type Special Programs P Prewash E Easylron L Low Spin R Extra Rinse Getting Started Using fabric softener is very important for optimum performance with automatic wash through dry loads Don t
12. off the water supply unplug the appliance and position the drain hose correctly Refer to the Water Drainage section p 4 Follow the When Needed Check the Pump directions p 18 to remove any debris from the pumps pre chamber Continued on next page Troubleshooting Operation Possible Cause ALGIS Eo Check that the plug has been correctly inserted into the socket and that there is electricity to the plug Check house circuit breakers fuses Replace fuses or reset breaker Washer should have separate outlet There is no power The dryer does not start Close the door The door is open The Delay Start has been programmed p 14 Water supply turned off kinked Move the program selector knob A to one of the Reset positions to cancel the program Then reset the controls without setting the delay start Turn both hot and cold faucets fully ON Make sure hoses are not kinked or pinched Make sure that the program selector knob A is set to a Dry position and gue le etie une sc that the Dry Time knob C is set to your desired dry time properly p 15 End of drain hose under water The drain pump is Make sure that the drain hose is positioned properly p 5 Follow the When Needed Check the Pump directions p 17 to remove any debris from the pumps pre chamber The dryer does not dry obstructed p 17 f 5 j E The drum has been Follow the Choosing A Load p 12 instr
13. parts of the washer dryer Vacations or anytime the machine is not in use it is recom mended that you unplug the machine from the socket and turn off the water supply to limit wear to the machines water circuit and to eliminate the risk of leakage Also leave the door ajar to allow for air circulation within the drum and door gasket area This will prevent unpleasant odors Don t neglect the detergent dispenser The detergent dispenser is removable and can easily be cleaned under running water see Detergent Dispenser Cleansing p 13 Never leave the washer dryer plugged in while cleaning During cleaning and maintenance the appliance should always be unplugged E General Maintenance Your washer dryer is designed to provide reliable service over many years A few simple steps will help to prolong its life and avoid problems e After washing is complete the water faucets should be turned off to relieve water pressure on the hoses e Before moving you washer dryer to a new location you must reattach the transit screws spacers you removed during installation p 5 e Wipe the inside of the washer dryer door with a soft cloth to remove any remaining moisture after washing Periodically a thin coat of paste wax should be applied to the inner door of the washer especially to the area that is immediately next to the porthole window This will protect the door finish from laundry aid spills and any discoloration that could
14. the drain pump to empty the tub switch the washer dryer OFF Select one of the Reset positions on the knob then switch it back ON If the knob continues to turn call for assistance When using the Easy Iron function without presetting a drying program the machine will stop and wait for your command to drain Simply press the Easy Iron button again and the machine will drain Turn the water supply OFF unplug the washer dryer and follow the When Needed Check the Pump instructions p 17 to unclog the pump Make sure that the drain hose is not squashed or kinked The drain hose should be as straight as possible Check that nothing is blocking the water flow Check that the detergent you are using is labeled For Machine Wash or Hand and Machine Wash or any similar wording Make sure that you are using only 1 2 tablespoons of low sudsing powdered detergent or liquid equiv and 1 2 tbsp of softener per wash load Make sure that the transit screws and spacers are removed The level of the washer dryer should be checked periodically Adjust the feet and check the machine with a level Make sure the drum is not overloaded Turn off the water supply unplug the appliance and refer to the Connecting the Water Inlet section p 4 to tighten the attachment Make sure the machine is resting level on a level surface Remove the dispenser drawer and wash it under tap water to remove any detergent residue that has built up Turn
15. type weight of material Sample Load 1 e Wash Cycle Regular Cotton Heavy Duty Dry Time 110 min e 2 3 Bath Towels 27 x 52 all 100 cotton e 1 Hand Towel 16 x 28 e 1 2 Wash Cloth s 13 x 13 Sample Load 2 e Wash Cycle Regular Cotton Heavy Duty Dry Time 75 110 min e 1 Flat Sheet 90 x 102 all 230 thread count e 1 Fitted Sheet 60 x 80 e 2 Standard Queen Pillowcases 21 x 32 Sample Load 3 e Wash Cycle Regular Cotton Heavy Duty Dry Time 110 min e 1 Hand Towel 16 x 28 e 1 Pair Jeans 35 waist 32 inseam e 1 Sweatshirt Large 50 cotton 50 polyester Operation Instructions About the Dispenser Drawer In compartment 1 Detergent for pre wash powder only In compartment 2 Detergent for washing powder or liquid In compartment 3 Fabric softener liquid In compartment 4 Bleach The dispenser drawer is where you add your detergent and other laundry aids How to Use the Dispenser Drawer Pull out the dispenser drawer to reveal the four compartments The drawer is divided into 3 1 compartments one for pre wash detergent one for wash detergent one for fabric softener and one for bleach see Fig 10 for a description of each e Add the correct type amount of detergent fabric softener and bleach if needed to the corresponding compartments see About Laundry Aids p 10 e When finished simply close the door Laundry aids will automatically be
16. using hottest water safe for fabric For heavy stains and tar apply nonflammable dressing cooking oils car grease dry cleaning fluid to back of stain Replace towels under stain frequently Rinse THOROUGHLY Wash using hottest water safe motor oils for fabric Ink Some inks may be impossible to remove Washing may set some inks Use prewash stain remover denatured alcohol or nonflammable dry cleaning fluid Mildew scorch May be impossible Wash with chlorine bleach if safe for fabric or soak in oxygen bleach and hot water before washing Mud Brush off dry mud Pretreat or soak with product containing enzymes Nail polish May be impossible Place stain face down on paper towels Apply nail polish remover to back of stain Repeat replacing paper towels frequently Do not use on acetate fabrics Paint varnish WATER BASED Rinse fabric in cool water while stain is wet Wash Once paint is dry it cannot be removed OIL BASED AND VARNISH Use solvent recommended on can label Rinse THOROUGHLY before washing Perspiration Use pre wash stain remover or rub with bar soap Rinse Wash using non chlorine bleach in hottest water safe for fabric Rust brown or yellow discoloration SPOTS use rust remover safe for fabric DISCOLORATION OF ENTIRE LOAD use phosphate detergent and non chlorine bleach 11 Operation Instructions Choosing aLoad Remember while your Splendide may have the largest drum size available on a combination washe
17. Fig 6 Standpipe Drain System Installations require a minimum 1 14 3 2 cm diameter standpipe with a minimum carry away capacity of 7 gallons 26 liters per minute Wall or Floor Standpipe Drain System The top of the standpipe must be between 25 62 cm 34 86 cm from the bottom of the washer Fig 4 Continued on next page WARNING Splendide denies all liability if these instructions are not followed correctly Installation Instructions Floor Standpipe Wall Standpipe Floor Standpipe 25 62 cm min 34 86 cm max 20 50 cm min with an air break Standpipe Floor Standpipe w Y Branch Tail Piece Sink Drainpipe System Entry into the sink drain system must be above the trap Fig 5 When routing the drain hose through cabinets or walls use a protective material such as electrical or duct tape to cover sharp Y Tail Piece edges that could damage the drain hose Use a suitable clamp to secure 20 62 cm min the drain hose to the Y branch or the disposer With a sink drainpipe ee nt pd system you may connect directly 1 to a disposer by following the least 20 50 8 cm above manufacturers attachment method 2 directly to a Y branch tail piece Po aia Washer WIN available at most hardware stores 3 Through the floor to a separate trap The trap must be vented to prevent siphoning To provide proper venting install an Air Gap Kit available at most hardware stores 4 To theto the
18. IVE If the hot water system has not been used for such a period before using the appliance turn on all hot water faucets and let the water flow from each for several min This will release any accumulated hydrogen e Do not use heat to dry articles containing foam rubber or similar textured rubber like materials e Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage if a break or rupture occurs e Do not reach into the appliance if the drum is moving e Do not tamper with controls e Repair or replacement of a part should be made only by a qualified service technician to prevent personal injury or damage to the machine Contact Splendide to locate an authorized repair service company near you e Qualified service personnel should clean the interior of the machine periodically e Disconnect power to the washer at the circuit breaker or fuse box or unplug the machine in an emergency or when servicing is required Have the installer show you and label the proper switch or fuse at the electrical disconnect box e Good safe practices and caution MUST be applied when installing operating and maintaining any appliance Follow basic precaution e Save these instructions Before loading Before loading the washer make sure the drum is empty Getting Started About Your Washer Dryer i Your New Appliance Your new appliance is an automatic washer and vented tumble dryer by Splendide Front loadi
19. LAR DRY washer dryer programs GENTLE Drain EXPRESS Spin Rinse Anti crease Rinse Qu Anti crease DRY PERMANENT DELICATES SILK Reset PRESS REGULAR i Low Spin Button G Press this button to reduce the spinning speed to 600 RPM during anyCotton Heavy Duty or Permanent Press cycle perfect for washing more delicate fabrics in these cycles E Extra Rinse Button H Press this button to add an extra rinse cycle to any Cotton Heavy Duty or Permanent Press cycle to improve rinsing results while washing full loads when more detergent is used NOTE Recommended for those who have detergent contact allergies Bi On Off Button I Press this button to turn your washer dryer ON or OFF In position machine is ON Out position machine is OFF NOTE Turning the appliance OFF does not cancel selected wash program E Status Door Lock Lamp L e Flashes Slowly Door can be opened The appliance is on and awaiting instruction or the cycle has ended e Steady Light Door lock is engaged Program accepted e Flashes quickly Program has ended and door lock is engaged NOTE Door may remain locked for up to 1 2 min after end of cycle E Auto Dry Lamp M Lights when the dry timer has been set and following the wash cycle the appliance will automatically run the selected tumble drying cycle NOTE Auto dry not available when Silk or Wool cycle is selected Getting Started Guide to the Wash Programs Special Total Type o
20. Splendide Washer Dryer Installation Instructions and Use amp Care Guide Lave linge s chant Mode d installation et d emploi Lavasecadora Instrucciones para la instalaci n y el uso Quick Reference Guide WD2100 WD2000S Splendide 2100 lume Splendide 2000 S Read All Instructions Before Using Door Lock SUPPLEMENT Follow these steps if you need to open the door to your washer dryer after a cycle has already begun To Open the Door During a Wash Cycle To Open the Door During a Dry Cycle 1 Advance the Program Selector to Reset and wait 5 1 Advance the Program Selector to Reset The Status seconds Door Lock LED will blink quickly to indicate the cycle has stopped but the door is STILL LOCKED DO_NOT DISCARD 2 Advance the Program Selector to Drain 8 o clock THIS INFORMATION and allow the machine to drain completely 2 When the Status Door Lock LED blinks SLOWLY SUPERSEDES THE 3 Advance the Program Selector to Reset The Status takes 1 2 minutes you can open the door INFORMATION FOUND IN Door Lock LED will blink quickly to indicate that the YOUR OWNERS MANUAL cycle has stopped but the door is STILL LOCKED 4 When the Status Door Lock LED blinks SLOWLY takes KEEP THIS PAGE WITH YOUR 1 2 minutes you can open the door OWNERS MANUAL FOR FUTURE REFERENCE IMPORTANT Spylendide WASHER DRYER Front Loading Washer Dryer O Copyright 2004 Westland Sales Cla
21. Time knob C before pressing the On Off button I Refer to the How to Dry Only section on this page e The Auto Dry lamp M will light to indicate that the dry timer has been set and at the end of the wash cycle the appliance will run the selected tumble drying cycle If the laundry load to be washed and dried is too large to dry then follow the instructions for wash only see How to Wash p 14 When the wash cycle has finished you ll need to remove some items up to 5096 after the wash cycle to give the remaining ones room to tumble freely while drying Now follow the instructions for dry only see How to Dry Only this page Repeat this procedure for the remainder of the load Opening the door during the dry cycle For your safety the door lock stays engaged for the duration of the dry cycle see Features p 7 However should you wish to open the door during the drying cycle you have two options e You can cancel the program by advancing the Program Selector knob A to a Reset position and waiting 5 seconds Pilot lamp L will flash quickly then slowly when the door lock is released Now turn the appliance off and open the door When finished close the door and follow instructions for dry only How to Dry Only this page e Or press the On Off button I to turn the appliance off Wait 1 2 min for the door lock to release then open the door When finished close the door and press the On Off but
22. WASH TEMP knob to HOT 2 Advancethe Program Selector knob to REGULAR in Cotton Heavy Duty 3 Press the ON OFF button IN and let the machine fill until antifreeze is in the drum 4 Advance Program Selector to a RESET Wait 5 seconds Status Door Lock LED will blink 5 Advance Program Selector to a SPIN position Let the antifreeze drain from the drum 6 Advance Program Selector to RESET Wait 5 seconds Status Door Lock LED will blink ce NJ urn the WASH TEMP knob to COLD Advance the Program Selector knob to REGULAR in Cotton Heavy Duty letthe machine fill until you see antifreeze in the drum Advance the Program Selector knob to RESET Wait 5 seconds Status Door Lock LED will blink Advance the Program Selector knob to SPIN Let the antifreeze drain from the drum Press the ON OFF button OUT Finished To use again flush the water pipes then Reconnect the water inlet hoses to the correspond ing HOT COLD faucets Turn the faucets N NOTE Check the water inlet hoses and pump periodically Refer to the Use amp Care Guide that came with the machine Plug the washer dryer into an appropriate electrical outlet or reconnect power supply With the ON OFF button in the off OUT position pour 1 2 TBSP of powder detergent or liquid equiv into the Detergent compartment inside the Dispenser Drawer Advance the Program Selector knob to an EXPRESS cyd
23. ad the following carefully before installing the washer dryer e Installation and grounding must be done in accordance with local codes and by a qualified installer Installation Instructions provided in this booklet are for the installers reference e Washer dryer MUST be installed on a strong level floor and in a protected dry and well ventilated area close to a power supply and drain outlet of sufficient capacity DO NOT install on carpet IMPORTANT Installation on carpet floors will cause the AN machine to vibrate and may result in excessive machine vibration during the spin cycles and loss of performance e The washer dryer should be plugged into a properly grounded 3 prong electrical outlet capable of 120 Volt 60 Hz 1300 W and 13 Amp It shouldn t be controlled by a wall switch or pull cord which could be turned off accidentally For your safety the third or round grounding prong must never be removed DO NOT USE AN EXTENSION CORD e DO NOT install or store this appliance where it will be exposed to weather or in an area where gasoline or other flammables are stored E Electrical e Machine Voltage Amperage 120V 60 Hz 1300 W 13 Amp e Connection 3 prong plug with 6 cord is provided with the machine e Circuit Protector 3 wire single phase 120V 60 Hz AC ona separate 15 Amp circuit Installation Requirements B Location This machine may be installed free standing as well as in a recessed area closet o
24. and plastic bags after the washer dryer has been unpacked j WARNING Plastic bags Styrofoam nails and other packaging m2 Remove the Transit Screws Spacers e For transportation the inside of the machine is supported by screws rubber grommets and spacers on the back panel Before using the washer dryer these items MUST be removed IMPORTANT Transit screws and spacers must be removed before operating the machine to allow proper operation of the machine and to prevent damage to the appliance e After positioning the washer dryer near the installation location remove the four screws Fig 1 with the rubber grommets and plastic spacers that are attached to them Use the plastic plugs provided in the accessories bag to fill in the holes tubes These items should be reinstalled to prevent damage if A IMPORTANT Retain the transit screws spacers and rubber or when you transport the machine in the future B3 Connecting Water Inlet e Ifthe water pipes you will be connecting to are new or unused run the water until clear to remove any debris that could clog the water valve screens or valves before connecting the machine NOTE Supply shut off valves should be easily accessible IMPORTANT Water pressure MUST range within the values indicated on the Technical Data chart p 1 e Included in the accessories supplied with your machine are 2 inlet hoses with 4 rubber washers preinstalled Check that the rubber washers ar
25. appliance Save these instructions For Your Safety Your washer dryer has been built in compliance with the strictest international safety regulations However for your safety the information in this manual must be followed to minimize the risk of fire or explosion electric shock or to prevent property damage personal injury or loss of life e Read all instructions before using any appliance e Do not wash or dry articles that have been previously cleaned in washed in or spotted in gasoline dry cleaning solvents other flammable explosive substances as they emit vapors that could ignite or explode e Before the appliance is removed from service or discarded remove the door to the washing drying compartment e Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user maintenance instructions or in published user repair instructions that you understand and have the skills to carry out e Do not allow children to play on or in the appliance e Do not add gasoline dry cleaning solvents items contaminated with cooking oil or other flammable or explosive substances to the wash water These substances give off vapors that could ignite or explode e Do not place flammable substances around your washer dryer during operation e Under certain conditions Hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more HYDROGEN GAS IS EXPLOS
26. ckamas OR 97015 Addendum to Owners Manual MODELS WD20005 Splendide 2000S WD2100 Splendide 2100 WDC6200 CEE Comb o matic 6200 WDC5200 Comb o matic 5200 QUESTIONS Splendide Service HQ Westland Sales 15650 SE 102nd Ave PO BOX 427 Clackamas OR 97015 Telephone oll Free 800 356 0766 Local 503 655 2563 Service Fax 503 722 9202 E mail service splendide com Website www splendide com Once a wash or dry cycle is underway the washer dryer door will LOCK for the duration of the cycle and will STAY LOCKED for up to 2 minutes afterthe cycle ends DO NOT attempt to open the door unless the STATUS DOOR LOCK LED is BLINKING SLOWLY WINTERIZATION SUPPLEMENT Follow theses steps if you need to winterized your washer dryer that s installed in a boat or RV To winterize your washer dryer 1 With the machine power OFF pour Y quart of RV type antifreeze into the washer drum 2 Close the door Advance the Program Selector knob to a SPIN position 3 Press ON OFF Button IN Wait 1 2 minutes 4 Press ON OFF Button OUT Unplug the washer dryer from the electrical outlet or disconnect power 5 Turn the water supply faucets OFF Disconnect the inlet hoses from the faucets Drain any remaining water from the hoses Finished Optional RV Winterization If you re currently pumping antifreeze through the fresh water system follow these steps to winterize 1 With the machine power OFF turn the
27. do so NOTE After the wash cycle has been set and accepted by the washer dryer turning the knob will have no effect except when it s on the Reset position But where did all the water go Simple Splendide washer dryers use the newest technology and need less than half the water to get wash results that are twice as good This is why you cannot see the water through the door Operation Instructions Howto Dry EH How to Dry Only Once you have loaded the drum with the laundry that needs drying see Load Types Sizes and Dry Times p 12 make sure that e The door is closed correctly The plug is secured in the socket The water supply is turned on The On Off button 1 is in the OFF OUT position e Depending on the type of fabric being dried turn the Program Selector knob A clockwise until one of the three Dry programs is aligned with the mark on the knob Cotton Heavy Duty dry program For cotton loads of less than 2 2 Ibs use the drying program for Permanent Press fabrics A spin cycle is carried out during drying if you select the e Set the Dry Time knob C to the desired dry time e Press the On Off button I to turn the machine ON The Status Door Lock lamp L will flash slowly for 5 seconds then will light steady to indicate that the program has been accepted At the end of the drying cycle e The Status Door Lock lamp L will flash quickly for up to 90 seconds to indicate tha
28. e Press the ON OFF button IN and allow the machine to run through the complete cycle to clean out any remaining antifreeze Finished Technical Data Technical Data Models Splendide 2100 Splendide 2000 S by Splendide WD 2100 Width 23 4 59 5 cm Dimensions Height 33 25 33 75 84 5 85 7 cm Depth 23 4 59 4 cm Drum Size 1 92 CF Capacity Washing 2 12 lbs Drying 2 8lbs Voltage 120 Volts 13 Amp 60 Hz Electrical Conn Max Absorbed Power 1300 Watts Water Conn Max Pressure 69 MPa 6 9 bar 100 PSI Min Pressure 0 05 MPa 0 5 bar 7 5 PSI by Splendide WD 2000 S Width 23 4 59 5 cm Height 33 25 33 75 84 5 85 7 cm Depth 22 2 56 4 cm Drum Size 1 6 CF Washing 2 10 lbs Drying 2 6lbs Voltage 120 Volts 13 Amp 60 Hz Max Absorbed Power 1300 Watts Max Pressure 69 MPa 6 9 bar 100 PSI Min Pressure 0 05 MPa 0 5 bar 7 5 PSI Spin Speed Up to 1200 RPM Up to 1200 RPM NOTE The manufacturer reserves the right to make any improvements to its appliances without giving prior notice Minimum Installation Spacing This appliance may be installed in a recessed area closet or alcove The installation spacing is in inches and is the minimum acceptable Additional Spacing should be considered for easy installation servicing and compliance with local codes and ordinances Installations must conform with the minimum dimensions indicated Recessed Front View
29. e installed in the ends of the inlet hoses to make a water tight seal at each connection point Connectthe straight ends of the water inlet hoses to the supply taps that have 34 BSP thread standard hose bib Connect the 90 angled ends 20 mm thread of these hoses to the inlet valves on the back of the machine Fig 2 NOTE Water Inlet valves are color coded Red Hot amp White Cold couplings can result The couplings should be tightened by IMPORTANT Do not use excessive force Damage to the N hand a tool should only be used if a leak occurs Optional Single Faucet Hook Up It is possible to run the machine on cold water only but a water supply must be connected to each inlet valve To do this we suggest you use a Y connector contact Splendide Connect the Y connector to a tap After checking that the 4 rubber washers provided are installed in the ends of the inlet hoses connect the straight ends of the hoses to the Y connector Fig 3 Then connect the 90 angled ends of these hoses to the inlet valves on the back of the machine Fig 2 NOTE When the machine is connected to a single faucet the water temp for the wash rinse settings is regulated by the temperature YOU set at the faucet B4 Water Drainage e Itis possible for the water to be discharged into a sink standpipe or drainpipe but an air break must be available at a min 20 height to prevent the machine from siphoning
30. ely with your Knowledgeable Splendide machine for complete details You ll find many answers to common Service Technicians are problems in the Avoid Service Checklist section of this manual If you just a phone call away review this section first you may not need to call for service at all NOTE You will be charged for a service call while the appliance is under warranty if the problems are not caused by defective workmanship or materials e f you do need service you can relax knowing that help is only a phone call away Call our Splendide Technical Service Assistance Department toll free at 1 800 356 0766 Monday Friday 8 00AM 5 00PM Pacific Time e Please have the model number and serial number of your washer dryer ready when you call 19 Splendide Splendide Division Westland Sales 15650 SE 102nd Ave PO Box 427 Clackamas OR 97015 USA Phone 1 800 356 0766 Email splendide westlandsales com Fax 503 656 8829 Web www splendide com Splendide Division Westland Sales 2002 u9ejnoo JM S SSOUISng X01 X 0 ZGZ VEO S6L 00c 6 S 0002 8 00 LEAM
31. f Fabric and Degree of Soil Program Detergent Fabric Programs Length Description of Wash Cycle Knob For Wash Softener Bleach Available of cycle Cotton Heavy Duty Exceptionally soiled whites colorfast 35 min wash cycle 3 rinse cycles fabiles eee tablecloths etc Super e e e Ets intermediate and final spin cycles i i i 27 min wash cycle 2 rinse cycles Heavily soiled whites colorfast Regular e e P L R intermediate and anal Spin cycles fabrics Slightl iled whit d light col 14 min wash cycle 2 rinse cycles salsas totes pais Express a AE intermediate and final spin cycles Rinse cycles Softener is automatically dispensed during the last rinse Rinse cycles intermediate and final spin cycles Spin cycle 1200 RPM high spin Draining and final spin cycle Drying cycle for cotton fabrics Cotton Heavy Duty Dry Program Reset Permanent Press Heavily soiled colorfast synthetics PELR Baby linen etc Regular o o Interrupts cancels program 26 min wash cycle 3 rinse cycles anti crease or spin cycle Delicate color synthetics All types of slightly soiled garments Ge ntle 19 min wash cycle 3 rinse cycles anti crease or spin cycle 13 min wash cycle 2 rinse cycles Delicate color synthetics e e PE L R All types of slightly soiled garments Express anti crease or spin cycle Rinse cycles Softener is automatically Rinse cycles anti crease or spin cycle dispensed during the
32. forget to empty all pockets before you load items in your washer dryer small objects can cause serious damage to your machine Preparing Laundry mSort amp Prepare Before washing you can do a great deal to ensure better wash results by preparing your laundry correctly Always read the fabric labels and follow their guidelines Separate items according to color fabric type and degree of soil Separate items that shed lint from those that attract lint Pre treat heavily soiled areas e Empty Pockets Fasten all hooks zippers and buttons Tie strings apron sashes etc Remove non washable buckles trims and belts e Turn knit garments inside out e Place delicate items such as bras shoulder pads underwear tights and stockings in a mesh laundry pouch to prevent tangling e Mend garments that are ripped or torn so that further damage is not done B About Pre washing Use your washer dryers Pre wash feature when washing excessively soiled clothes that contain deeply embedded dirt such as men s work clothes or children s play clothes E About Pre treating Pre treat heavily soiled areas of clothing with a pre wash spray liquid laundry detergent or a laundry detergent water paste mixture over the stains before washing see Stain Removal Chart p 11 for treatment of specific stains 10 About Laundry Aids E Detergent Your Splendide requires smaller amounts of laundry aids to get fabrics cleaner If your pre
33. hlorine bleach Do not bleach when needed when needed Stain Removal Chart Always check the care labels before treating a stain and check the fabric for colorfastness by testing stain remover on an inside seam Stain Treatment Adhesive tape chewing gum rubber Apply ice Scrape off excess Place stain face down on paper towels Saturate with prewash stain remover or nonflammable dry cement cleaning fluid Baby formula dairy products Use product containing enzymes to pretreat or soak stains Soak for 30 minutes or more Wash Beverages coffee tea soda Pretreat stain Wash using cold water and bleach safe or fabric Blood Rinse w cold water Rub w bar soap or pretreat or soak with product containing enzymes Wash using fabric safe bleach Candle wax crayon Scrape off surface wax Place stain face down between paper towels Press with warm iron until wax is absorbed Replace paper towels frequently Treat remaining stain with prewash stain remover or nonflammable dry cleaning fluid Hand wash to remove solvent Wash using bleach safe for fabric Chocolate grass mustard tomato Pretreat or soak in warm water using product containing enzymes Wash using bleach safe for fabric Collar or cuff soil cosmetics Pretreat with prewash stain remover or rub with bar of soap Dye transfer on white fabric Use packaged color remover Wash using bleach safe for fabric Grease oil tar butter fats salad Scrape residue from fabric Pretreat Wash
34. ied Jeans towels and similar rather thick articles will take longer to dry 12 Helpful Hints Combine large and small items in one full load When washing single items such as a sweater towel or jeans add 1 or 2 similar items to help balance the load Single heavy items such as a bathrobe can be washed separately Never use your washing machine to wash torn fraying or non hemmed linen If it s absolutely necessary place these items in a mesh bag for protection Do not wash colored linens with whites Do not wash rugs that could come apart and clog your pump Colored T shirts printed ones and sweatshirts last longer if turned inside out before washing Printed T shirts and sweatshirts should always be ironed inside out For more delicate garments protect underwear tights stockings and delicate items by placing them in a mesh laundry pouch while washing and drying Dungaree alert Overalls have straps with hooks that can damage the drum of your washing machine or other garments during wash To minimize the risk place hooks in the pockets and fasten with safety pins When using the Wool cycle for best results we recommend that you use a detergent that is for wool garments taking care not to wash more than 2 2 lbs ilSample Wash Through Dry Loads To get you started here are a few sample load sizes that can go directly from wash through dry NOTE Data purely indicative Actual drying times will vary depending on
35. m Selector knob keeps turning The washer dryer doesn t drain or spin a EE C The washer pim produces too i ie much foam p E eui Excessive A vibration during A the spin cycle a lt 5 1 ie 1 i i The washer dryer leaks 18 There is no power Door is open The Delay Start has been programmed p 14 Controls not set properly p 14 Water supply is turned off or the supply hoses are kinked Wall drainage system doesn t have a breather pipe Drain hose is positioned too low causing siphoning Fig 6 p 5 Hose is not connected correctly to the tap p 4 Water supply is not adequate p 2 Water inlet hoses are kinked or clogged The machine needs to be Reset The selected program incorporates a manual draining command p 6 The drain pump is clogged p 17 The drain hose is kinked or clogged The detergent used is not suitable for washing machines Too much detergent or softener is being used p 10 The transit screws and spacers are still installed p 4 The washer dryer is not leveled correctly p 5 Overloading p 12 The inlet hose is not properly attached p 4 The machine is not level p 5 The detergent dispenser is obstructed p 13 The drain hose is not positioned properly p 4 The drain pump is obstructed p 17 Possible Cause B IE UM Cere e Check that the plug has been correctly inserted into the socket a
36. nd that there is electricity to the plug Check house circuit breakers fuses Replace fuses or reset breaker Washer should have separate outlet Close the door Move the program selector knob A to one of the Reset positions to cancel the program Then reset the controls without setting the delay start Refer to the How to Wash section p 14 to make sure your controls are set correctly Turn both hot and cold faucets fully ON Make sure hoses are not kinked or pinched Make sure that the wall drainage system has a breather pipe If you live on an upper floor of your building there may be a problem with your drain trap To solve this problem a special valve must be installed Check that the standpipe is at least 25 high and not more than 34 high Make sure that no more than 6 of drain hose is inserted into the standpipe If the problem still persists after these checks turn the water supply OFF and call for assistance Review the installation instructions and make sure the hoses are connected properly to the tap Check water pressure The water heater may be malfunctioning Water may be being used elsewhere in your home Make sure that the hot and cold water inlet faucets are turned fully ON Free the inlet hoses of any kinks and clear them of any clogs If the water is very calcareous or if work has recently been carried out on the water piping the tap filter could be clogged with particles and debris Wait a few minutes for
37. ng with a stainless steel drum and an extra large door opening for easy loading and unloading it features 9 wash programs 6 water temp settings 3 dry programs a delay start option and a 1200 RPM max spin speed mFeatures e Automatic Dispenser Drawer Your washer dryer has a convenient dispenser drawer that dispenses laundry aids detergent bleach softener automatically Delay Start Option Your washer dryer offers a delay start option allowing you to run your washer at a later time or during off peak hours Auto Water Energy Control Your washer dryer doesn t need high medium or low water level settings for different wash load sizes It automatically adjusts the amount of water and energy to use for each load e Safety Door Lock Your washer dryer has an automatic door lock feature that engages for the duration of the wash and dry cycles and protects you from opening the door when there is water or high heat and steam within the drum Express Wash Your washer dryer features Express wash cycles to wash your lightly soiled Cotton Heavy Duty or Permanent Press fabrics in less time More Rinse Cycles Extra Rinse Most washers have only 1 rinse following each wash while your Splendide washer dryer has up to 4 It rinses 3 times after every wash except Express Wash and features an Extra Rinse button that adds yet another rinse to remove even more dirt detergent from fabrics recommended for those with detergen
38. owever small objects may accidentally fall into the pump coins hair clips loose buttons and other small items To avoid possible damage they are withheld in an accessible pre chamber at the lower end of the pump NN IMPORTANT Before attempting to examine this pre chamber first ensure that the machine has finished its program and is empty As with any maintenance unplug the machine To gain access gently ease down the top of the toe kick panel at the base of the front of the machine with a screwdriver or similar item to release it Then ease the top edge forward to allow it to be lifted clear Fig 13 e Place a shallow dish or tray below the cover of the pre chamber to catch the small amount of water present Helease the cover by turning counter clockwise Fig 14 Hemove any items or debris e Securely replace the cover by turning clockwise Refit the toe kick panel by inserting the hooks on its lower edge into the slots and ease the top edge back into position Clear She Pump Pre Chamber As heeded 17 Troubleshooting Avoid Service Checklist In most cases when your washer dryer fails to work the problems arising can be easily solved without having to call for a technician Before calling for assistance always check these points Operation The washer does not start a Y The machine E continuously 7l e miis and drains water Water does not enter the washer The progra
39. r dryer it s still smaller than a standard top loading washer Loading the drum correctly will reduce dry times and increase washing per formance considerably Mls using a combination washer dryer much different than what I m use to Yes in some ways You are washing and drying in the same drum 1 5 1 9 cu ft and load sizes are smaller Wash cycles are similar but because combination washer dryers are compact and operate using 115V vs 230V dry times are longer Instead of washing several bulky loads of laundry in one day you ll learn to adjust your laundry habits to launder smaller more convenient loads every day or two i Wash Through Dry Loads Your machine can wash larger loads than it can dry Remember separate washers and dryers have drums of different sizes the washer is half the size of the dryer and your machine washes and dries in the same drum Therefore when you program your machine to wash through dry automatically you must load the drum according to the maximum recommended load size for drying see Load Types sizes and Drying Times below NOTE automatic wash through dry not available when Silk or Wool cycle is selected MH Load Types Sizes and Drying Times Drying times depend largely on the type of material some fibers absorb more water than others on the dampness of the articles when drying is started 1200 RPM spin vs 850 600 RPM spin and on the amount of laundry that is being dr
40. r alcove e Minimum Installation Spacing 0 on sides and 1 in front and back NOTE Additional installation spacing needs to be considered for easy installation servicing and compliance with state and federal codes e Floor Must support at least 280 lbs and be a solid level surface DO NOT install on carpet e RV Marine Applications When locating the appliance in a towable trailer or watercraft position the machine over the axles or mid ship where movement is at a minimum Block the machine to prevent extreme movement Exhaust Requirements Ducting installing Rigid or flexible metallic duct required Ducting must slope downwards and away from the machine DO NOT exhaust dryer into a chimney furnace cold air duct attic crawl space or another duct used for venting If cabinet door is installed a min of 8 sq in should be provided for make up air Louvered doors with equiv air openings are acceptable Allow clearances behind door s to avoid rubbing between back of cabinet door s and front of unit control panel Additional clearances for wall door and floor molding may be required Rigid or flex metal metallic ducting should be used Exhaust ducts should be as short and straight as possible and slope downwards and away from the machine NOTE Long exhaust ducting can extend drying time collect lint and may affect drying performance The exhaust duct must end with an approved exhaust vent hood with swing out dampe
41. r s or tailpiece with louvers Check that all ducting is clean and lint free Use ducttape or screw clamps to secure all joints Use duct tape or screw clamps to secure the duct to the round flange vent located on the back ofthe machine Fig 8 E Drainage e Standpipe Diameter Capacity Needs a 1 4 minimum diameter standpipe with a minimum carry away capacity of 7 gallons per minute e Top of Standpipe Must be between 25 34 high from the bottom of the machine e Qutlet End of Drain Hose provided with the unit Must be at least 20 above the bottom of the washer dryer An air break must be available at the standpipe to avoid siphoning No more than 6 of the drain hose should be inserted into the drain pipe to prevent siphoning ilSplendide Accessories Available Separately e Faucet Adapter Kit allows for a direct faucet connection Optional Drain A Way Pans designed to be drain plumbed WARNING Splendide denies all liability if these instructions are not followed correctly Installation Instructions Installation Removal B1 Unpacking Your Washer Dryer e Carefully remove the packing materials with care not to damage the drain hose and power cord that are shipped installed on the machine Check that the machine is intact Report any damage immediately e Position the washer dryer near the desired installation position parts are not children s toys and can be potentially dangerous Destroy the carton
42. result from these spills e Clear the pump pre chamber if it gets clogged See When Needed Check the Pump p 17 e The use of a de liming product is recommended every wash ONLY if the water is particularly hard or rich in lime content Normal detergents already contain de liming agents A periodical wash cycle with a dose of a de liming product without detergents or laundry may prove useful e Never use too much detergent or additives because this could cause an excessive amount of foam increasing the potential for damage to the component parts of your washer dryer See About Laundry Aids p 10 e tis important to wash the detergent dispenser drawer regularly If dried laundry aids accumulate place the dispenser under running water for a few minutes until clean See Detergent Dispenser Cleansing p 13 Continued on next page Easy Care and Maintenance Monthly Yearly Maint Winterizing Your Machine If needed follow these steps to winterize your machine e With the machine power OFF put 1 2 quart of R V type antifreeze in the drum Close the door e Turn the Program Selector knob to Spin Turn the power On Let the machine spin for 1 2 min e Turn the power OFF Unplug the washer or disconnect power e Shut off both water faucets Disconnect water inlet hoses from faucets and drain DONE To Use Again e Flush water pipes e Reconnect water inlet hoses to the corresponding HOT and COLD fa
43. t contact allergies e Foam Removal System Your machine automatically measures the amount of foam in circulation and adds water to the drum to remove excess foam for the highest rinsing performance e Recirculating Wash Feature With your Splendide washer dryer no detergent is wasted Water recirculates and redistributes detergent throughout the drum in a way that assures all detergent is dissolved for max resource efficiency Automatic Balance System Every Splendide washer dryer incorporates the latest motor technology Automatic Balance System ABS When it detects an out of balance load the motor will adjust speed or come to a complete stop and reposition the load automatically e Impulse Spin Technology Your machine features Splendide s exclusive IST processor that varies pulse in low spin for less wrinkling less wear on clothing less noise less vibration and improved energy efficiency e Dry Spin During Cotton Heavy Duty drying there is an additional spin for improved drying performance Getting Started Understanding the Control Panel E Program Selector Turn clockwise only A Use this knob to select one of 9 wash programs see Guide to the Wash Programs p 10 e Delay Start Option You can also use this knob to delay the start of any wash program by 1 3 9 or 12 hours see How to Wash p 14 progress or set a new one advance the Program Selector j IMPORTANT Should you wish to
44. t the cycle is finished but the door is still locked e When the Status Door Lock lamp L light flashes slowly turn the washer dryer OFF by pressing the On Off button 1 e Open the door and remove your laundry See A Special Note About Condenser Drying above on this page e After removing your laundry leave the door open to allow for air circulation inside the drum to avoid the formation of bad odors Warning During the drying phase the door tends to get quite hot Do not attempt to open the door when the door lock is engaged Do not use the appliance to dry clothes that have been washed with flammable or chemical solvents e g trichlorethylene This appliance can only be used to dry clothes that have been pre washed in water Do not use the appliance to dry foam rubber or similar materials EH How to Wash amp Dry Automatically If you want your load to go automatically from wash to dry e Load the drum according to the recommended maximum load sizes for drying See Wash Through Dry Loads p 12 To protect your delicate fabrics this machine will not allow a dry program to be set when the Silk or Wool program is selected when going from wash to dry automatically always use fabric j IMPORTANT To optimize the performance of your machine softener during the wash cycle About Laundry Aids p 10 e Simply follow the instructions for wash only see How to Wash p 15 and set the Dry
45. ton again The dryer will automatically resume the selected program where it left off 15 Easy Care and Maintenance Regular Maintenance It s Easy With just a bit of care your washer dryer will repay you with loyalty and devotion With the necessary upkeep it will give you excellent washing and drying results for years to come EH Cleaning the exterior The exterior of your machine should be cleaned with a rag dipped in lukewarm water and soap Do not use polish of any kind on the plastic trim Some polishes contain agents which may damage plastics E Cleaning the Interior If you live in an area where phosphate detergents are banned it may be necessary to recondition the washer periodically If a non phosphate detergent must be used body oils and detergent may accumulate in the washer tub This is particularly evident in hard water areas or homes where heavily soiled garments are regularly laundered To remove this buildup run the washer through a complete cycle using HOT water and 2 cups of a non precipitating water conditioner Do not add any clothes laundry detergent or other laundry aids Once all the accumulation has been removed your laundry should be satisfactory if you follow the preventative suggestions in this book 16 Helpful Hints Clean the exterior and rubber parts of the appliance gently with a soft cloth dipped in warm soapy water Never use solvents or abrasives to clean the external or rubber
46. ucets Turn on both water faucets e Plug in washer or reconnect power e Run the washer through the Express cycle with 1 2 tablespoon of powder detergent or liquid equiv to clean out antifreeze DONE Optional RV Winterization If currently pumping antifreeze through the fresh water system follow these steps to winterize your machine e With the machine power OFF turn the Wash Temp knob to WARM e Turn the Program Selector knob to Regular wash located in the Cotton Heavy Duty section of the dial Turn the power ON e When you see antifreeze in the drum turn the power OFF Now advance the Program Selector knob to Spin e Turn the power ON Allow the drum to spin for 30 seconds e Turn the power OFF DONE Check the Water Inlet Hoses Periodically inspect and replace hoses if bulges kinks cuts wear or leaks are found Remove and clean the filters and the water valves Fig 12 Replace inlet hoses as needed to reduce the risk of hose failure years of use to reduce the risk of hose failure Inspect and replace inlet hoses if bulges kinks cuts or leaks are found NOTE When replacing your inlet hoses mark the date of replacement on the label with a permanent marker IMPORTANT Replace inlet hoses at least every five Rems Filters Using Tweazers Clear and Replace When Needed Check the Pum Your washer dryer comes equipped with a self cleaning pump that does not require regular cleaning and maintenance H
47. uctions in this manual for properly overloaded p 12 recommended load sizes for drying Washing is too long Excess wash time may create lint Select a shorter wash cycle p 9 Lint or residue on clothing Detergent not dissolving Overloading p 12 Try a liquid detergent and or use a warmer temperature setting Make sure the drum is not overloaded For wash loads you should be able to close the door easily items should not be tightly packed Dispensing balls will not operate correctly in this machine Add liquid fabric A fabric softener softener to the fabric softener compartment Stains on the load dispensing ball was used Powdered detergent in low spin Large load in Express wash Consider using liquid detergent in wash cycles with low spin For best results use Express wash for small lightly soiled loads Avoid mixing heavy fabrics with light fabrics Incorrect sorting p 10 Overloading p 12 Load your dryer so clothes have enough room to move freely in the drum while drying Incorrect wash cycle p 9 Match cycle selection to type of fabric you are using Repeated washing in Wrinkli water that is too hot may cause wrinkling rinklin s Clothes matted to drum Use the recommended amount of fabric softener during the wash cycle after Spin p 10 If You Need Service Every Splendide washer dryer comes with a Limited Warranty Please read the Limited Warranty Statement that came separat
48. vious washer was a top loader you may not need to add as much or any detergent to initial wash loads Old detergent trapped in fabrics will release during the tumble action wash cycle e Amount 1 2 tablespoons of any powder laundry detergent or liquid equiv per wash load However if you have access to them low sudsing high efficiency HE detergents are designed for use in front loading machines and are recommended e Adjustthe amount for heavily or lightly soiled loads Use more if water is extremely hard use less in soft water If garments have been pretreated you won t need as much or any detergent at all e Your machine features an internal foam removal system however if the suds level rises too high set the Program Selector knob A to Rinse and allow the machine to rinse out IMPORTANT The suds level should never rise more than half way up to the porthole Too much foam will rise through the detergent dispenser and make a mess on your floor i Liquid Fabric Softener Using fabric softener causes items to release from the drum immediately after your washer dryer s high speed spin helping clothes to dry faster while minimizing wrinkling and softening fabrics e Amount 1 2 tablespoons of a bio friendly or similar brand per wash load These softeners tend to appear light in color and dissolve more quickly in less water minimizing build up within your machine e Adjustthe amount for heavily or lightly soiled loads
Download Pdf Manuals
Related Search