TTP 5000 Kiosk Printer Sub
Contents
1. 2 PRODUCT PRESENTATION Paper roll Paper Form feed Print module support shaft release lever button Cutter module Presenter module Document exit Power indication lights SW95018C R1 Figure 1 Printer exterior 4 TTP 5000 Kiosk Printer Sub systems Operating Instructions 96 06 3 LOADING THE PAPER 3 1 Removing remaining paper and core If there is any paper left in the printer proceed as follows 1 Lower the paper release lever to horizontal position Remove any remaining pieces of paper 2 Pull out the paper rearwards and remove the core from the paper roll support shaft If necessary clean the paper path by blowing or wiping with a soft brush Sw96077 Figure 2 Remove the old paper roll 96 06 TTP 5000 Kiosk Printer Sub systems Operating Instructions 5 3 2 Loading new paper roll 1 Turn the paper roll as shown The paper should be inserted into the printer with the temperature sensitive side up Temperature sensitive coating Swe96080 Figure 3 Turn the paper roll with the temperature sensitive side up 2 Tear off approximately 0 5 m from the new paper roll Glue or similar substance SW96081 Figure 4 Tear off 0 5 m of the paper A CAUTION This is important since the outer end of the paper is usually fixed to the roll with some type of glue or self adhesive substance that might otherwise cause paper jam or even printhead damage 6 TTP 5000 Kiosk Printer Sub systems Ope2. Please return by mail to Swecoin Promakon AB Box 132 S 191 22 SOLLENTUNA Sweden or by fax to Int 446 8 96 50 54 Nat 08 96 50 54 TTP 5000 Kiosk Printer Sub systems Operating Instructions 11 This page intentionally left blank TTP 5000 Kiosk Printer Sub systems Operating Instructions 96 06
3. TTP 5000 Kiosk Printer Sub system Operating Instructions Part No SWC 809 A A VV EE OON Related manuals TTP 5000 std Technical Specification TTP 5000 Installation Manual SWC 761 TTP 5000 Service Manual SWC 803 This is a publication of Swecoin Promakon AB Box 132 S 191 22 Sollentuna Sweden Phone int 46 8 92 00 80 nat 08 92 00 80 Fax int 46 8 96 50 54 nat 08 96 50 54 BBS _int 46 8 92 00 88 nat 08 92 00 88 Swecoin Promakon AB 1996 All rights reserved Reproduction in whole or in parts is prohibited without written consent of the copyright owner We have taken great care to ensure that the in formation in this manual is correct and complete However if you discover any errors or omissions or if you wish to make suggestions for improvements you are welcome to send your comments to us Swecoin Promakon AB disclaims any liability resulting from the use of this information and reserves the right to make changes without n otice First edition June 1996 Printed in Sweden TTP 5000 Kiosk Printer Sub system Operating Instructions Contents VINTRODUGTION eise eende ese N es nee ede eke ee ee Ge ve Ee ne ee ede ee ee eed 3 1 1 Aboutthisimarnual 2 EE EE ee GE ea esed De Se Ee Ee Ek 3 1 2 UpdatiNg ER EE N ee GT DE DEE EE ee Gee De DEE ee Ee eed 3 S Safety precautions EE Ee ter ee Ee Se GE EED GEDRA ee ge De Ge A 3 2 PRODUCT PRESENTATION eene see eens se
4. by the printer Release the paper feed button to stop the printing The printer cuts and ejects the document but remains in the self test mode Renewed actuation of the paper feed button produces a demo test print out followed by cut and eject Exit the self test mode by switching the power OFF and then ON again The printer is now operational again CLEANING Remove paper dust by blowing it away or by using a vacuum cleaner or a soft brush STORAGE A CAUTION If the printer is not to be used for a long period of time disengage the printhead from the platen by lowering the paper release lever Both the printhead and the platen will otherwise be deformed TTP 5000 Kiosk Printer Sub systems Operating Instructions 96 06 6 FAULT FINDING Symptom Nothing is printed but the document becomes cut and ejected Printer does not work at all Test document can be produced as described in Section 3 3 but the printer works strangely in normal operation Printout contains white longitudinal lines Faint print dots Suggested actions Verify that the paper roll is turned the with the temperature sensitive side up See Section 3 2 Verify that the paper used meets the paper specification See TTP 101 Technical Specification Verify that the ribbon cable connector at the top of the print module is fully inserted Verify that the paper release lever is in its vertical position Red and green voltage indicato
5. ee ee ee ee eek EER a Gee RARR RR KEER ee RR RR n Re RR sen ERG ee RR ARE ee 4 3 LOADING THE PAPER sesde ee ee ey ky EE EER ee gery Wee de ee Ee ey KYK EE EEUE UP vee od 5 3 1 Removing remaining paper and Core ee RR ER Re ee ek ee ee 5 3 2 Loading new paper roll ee ee nnn 6 33 AGS N 8 DEM YI cec 8 5 STORA GE aa Pe 8 6 FAULT FINDIIN eN EE en err end aeaea aaan aaia 9 REGISTER NOW Please fill in the registration form inserted at the end of this manual and return it to us via mail or fax This will put you on our mailing list for keeping you informed of product changes manual updates etc Registration date for your own records 96 06 TTP 5000 Kiosk Printer Sub systems Operating Instructions 1 FCC COMPLIANCE STATEMENT This eguipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated within a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expenses TTP 5000 Kiosk Printer S
6. r lights should be ON see Chapter 1 If both lights are OFF check that the power cable is connected at both ends and that the power supply is switched ON If only the green light is OFF call service Verify that both ends of the data cable are connected Application program might be incorrect Contact system manager Printhead needs cleaning or is defect Call service The paper used may not meet the paper specification See TTP 101 Technical Specification The printhead may need cleaning Call service Contact service personnel in case of other error symptoms or if the suggested actions do not remove the problem 96 06 TTP 5000 Kiosk Printer Sub systems Operating Instructions This page intentionally left blank TTP 5000 Kiosk Printer Sub systems Operating Instructions 96 06 96 06 User Registration Form SWC 00809 A After you have returned this registration form to us we will keep you informed of product changes manual u pdates etc through our bulletin service Do not return this form if you already have registered a previous edition of this manual You may also use this form to inform us about changed registration data name address phone No etc but please tick the Changed information box in that case 2 New registration LJ Changed information Name Organization Postal address street box area etc Zip Postal code City State Country Telephone Fax E mail
7. rating Instructions 96 06 96 06 3 Raise the paper release lever to vertical position 4 Turn the paper roll as shown and insert the edge of the paper into the back of the print module Note that the paper should pass beneath a plastic bar see arrow SWw96078 R1 Figure 5 Feed the paper into the printer 5 Keep feeding the paper into the print module and press the paper feed button momentarily The printer will now automatically grab and advance the paper cut it and eject it The leading edge of the next document will now have a properly cut top edge An alternative way of loading the paper is to feed it manually with the paper release lever down until the paper becomes visible in the presenter module Then raise the paper release lever and press the paper feed button Sw96079 R1 Figure 6 Perform cut and eject 6 Make a test printout see Section 3 3 TTP 5000 Kiosk Printer Sub systems Operating Instructions 3 3 Print test The print test can be used for example to verify that the paper is correctly loaded or that the printer works correctly after you have removed an obstructing paper particle etc 1 2 3 Verify that the printer is switched OFF Press the paper feed switch and keep it depressed Switch the power ON and continue keeping the paper feed button depressed for at least 5 seconds This produces a printout showing some technical data and repeatedly all characters that can be produced
8. ub systems Operating Instructions 96 06 1 1 1 2 1 3 96 06 INTRODUCTION About this manual This document describes the daily handling of the TTP 5000 printer Since the behavior of the printer to a large extent depends on the design of the application software please also refer to the applicable system documentation Updating This manual will be updated from time to time as printer functions and features are added or amended No automatic distribution of new editions is however planned Registered manual owners see registration form at the end of the manual will be kept informed about new editions product changes etc through our bulletin service Updated manuals can be ordered by fax or phone Provided you are using an IBM compatible PC you can also download the current manual edition from the Manuals area of our BBS phone number at the back of the title page The manual is supplied in the Adobe Acrobat file format By downloading the free Acrobat Reader program from the same area in the BBS you can view and print the manual locally without the need of any other program If you require functions not found in the manual edition at your disposal please consult one of our offices for information Safety precautions Handling the TTP 5000 in a safe way requires that you keep your fingers away from the cutting mechanism when the power is switched ON TTP 5000 Kiosk Printer Sub systems Operating Instructions
Download Pdf Manuals
Related Search