DO NOT REMOVE PRIOR TO SALE! Model No. 0340
Contents
1. 3 Actuate the inflation system by jerking firmly downward on the pull tab The PFD should fully inflate within 5 seconds 4 Pull neck strap over head and adjust See MAXIMIZING PERFORMANCE on Page 9 5 Get into shallow water just deep enough that you can stand with your head above the surface 6 See if the PFD will float you on your back or just slightly back of vertical In a relaxed floating position verify that your mouth is well above the water s surface Note the effect of where you hold your legs on how you float 7 Get out of the water and remove the PFD Remove the used CO cylinder from the PFD inflator Completely deflate the PFD using the oral inflator 8 Let the PFD dry thoroughly REARM and REPACK the PFD in accordance with the manufacturer s instructions refer to Pages 11 12 and 13 17 HOW DO YOU TEST YOUR PFD USING THE ORAL INFLATOR 1 2 To test your inflatable PFD you will not need any spare parts Remove the CO cylinder to prevent inadvertent activation of the manual inflation which could potentially damage the PFD Inspect the threaded end to confirm it s un used Put on the PFD Get into shallow water just deep enough that you can stand with head above the surface If you are a weak or non swimmer inflate the PFD partially so that you are supported well enough to complete inflation without touching bottom either orally or manually Note this level of inflation because it is the min2. minimum 15 5 pounds after CO inflation 22 5 pounds after full inflation See Donning and Inflation instructions pages 7 amp 8 Inflation System Manual Inflation Mechanism located on front of chamber Oral Tube located on front of chamber CO Cylinder 16 Gram 3 8 thread USE REPLACEMENT KIT NO 0925 GENERAL ARRANGEMENT Oral Tube N Inflator Body Strap Mechanism Velcro a COE Neck Adjustment Strap Window Revised 2006 05 08 ll CONDITIONS FOR TYPE V APPROVAL Conditional approvals are granted by the Coast Guard for PFDs that 1 Do not meet all the requirements for approval under the Type through IV categories but offer other significant safety features or 2 Have features or uses not found in Types through IV PFDs that require special user knowledge The conditions let the user overcome design traits that would otherwise prevent approval Wearing a PFD is one of the most important things you can do to help you save your life if you accidentally fall in the water Finding a comfortable PFD that you will wear is the key This PFD design offers the significant safety features of being lightweight low profile and comfortable for continuous wear This PFD must be worn to meet carriage requirements so that it is available on the wearer when needed This PFD is also approved as a Type V because the buoyancy provided by the CO gas from the cylinder does not provide as mu
3. person on board To be considered serviceable this PFD shall not exhibit deterioration that could diminish its performance such as broken or deformed hardware detached webbing rotted structural components air leaks or nonfunctional oral tubes Unless worn inflated this PFD must also be properly armed with a full CO2 cylinder inflation system indicator and an accessible manual inflation lanyard Since this PFD is approved only when worn it must be worn under the conditions specified on Page 1 Ill INSTRUCTIONS FOR USE Know your PFD Familiarize yourself with its features and practice using it before attempting to use it in deep water or in an emergency You must accept responsibility for proper use and care of this device and in water trials to check its performance This device is not recommended for non swimmers since panic by the user in an emergency situation can prevent proper donning and inflation This PFD is not approved for children under 16 PRE DONNING INSTRUCTIONS Check the following before using this PFD 1 Inspect PFD for damage 2 Examine inflation mechanism status indicators 3 Examine CO cylinder face for puncture hole 4 Be sure cylinder is screwed in tight Read below for more detailed information 1 Inspecting Your PFD for Damage Make sure that the PFD is free of rips tears or punctures This type of damage on the outside covering indicates that the Inflatable Chamber may have been exposed to pot
4. TO 21 1 60 to 70 2 TO 7 HOURS 2 TO 40 HOURS 21 1 TO 26 7 70 to 80 2 TO 12 HOURS 3HOURS TO INDEFINITE Over 26 7 Over 80 INDEFINITE INDEFINITE PFDs can increase survival time because they allow you to float without using energy treading water and because of their insulating properties Naturally the warmer the water the less insulation you will require When operating in cold waters below 60 F 15 6 C you should consider using a coat or jacket style PFD or a Type V Thermal Protective PFD as they cover more of the body than the vest or belt style PFDs 19 Some Points to Remember About Hypothermia Protection 1 Always wear your PFD Even if you become incapacitated due to hypothermia the PFD will keep you afloat and greatly improve your chances of rescue Do not attempt to swim unless it is to reach a nearby craft fellow survivor or a floating object on which you can lean or climb Swimming increases the rate of body heat loss In cold water drown proofing methods that require putting your head in the water are not recommended Keep your head out of the water This will greatly lessen heat loss and increase your survival time To conserve body heat use the standard H E L P position Keep your arms as close to your body as possible to reduce the amount of skin surface that is exposed to the water Keeping water out of your arm pits is especially important Drawing your legs up into a seated position with your
5. arm the CO inflation system after each discharge The CO cylinder is good for only one inflation and then must be replaced Use ONLY genuine Stearns replacement kits for rearming your PFD See Pages 11 and 12 for rearming instructions NEVER wear inside clothing that can restrict expansion NEVER inflate in a tightly confined space NEVER inflate with any type of pump NEVER actuate with CO inflator if the belt is already fully inflated NEVER use in below freezing temperatures unless worn partly inflated At or below 40 F inflation time with CO2 gas will be longer Wearing a partially inflated PFD under these conditions will provide some initial buoyancy while the PFD fully inflates Caution Do not fully inflate orally and then inflate with the CO2 cylinder Repeated CO inflation after oral inflation will damage the PFD to the point that it will not hold air or float AVOID contact with sharp objects AVOID exposure to extreme heat 140 F or higher Failure to heed the above cautions may result in personal injury or death DONNING and INFLATION INSTRUCTIONS After completing the pre donning check follow these instructions to don inflate and adjust the PFD for maximum performance 1 Buckle the deflated belt around your waist and adjust to snug fit by pulling on the free end of the belt Secure the excess strap by tucking it under the belt Always position the belt with the center window in front The Velcro opening
6. should be on the bottom STEP 1 The Jerk to Inflate Snap buckle snug waist strap lanyard should be hanging downward wx 2 Pull down on the Jerk to Inflate lanyard to inflate chamber STEP 2 Jerk tab to Inflate 3 Grasp the neck adjustment strap tucked under the inflated chamber Slip the strap located at the center of the chamber over your head STEP 3 Put webbing over head DONNING INSTRUCTIONS CONTINUED 4 Adjust the length of the neck strap for desired comfort and head support Pull down on the adjustment strap to tighten or lift up the plastic slide to loosen 5 After CO inflation the performance of the PFD may be satisfactory without further action However higher buoyancy is easily available through second stage inflation Using the oral inflation tube you may top off buoyancy to the desired level STEP 5 Oral Inflate MAXIMIZING PERFORMANCE Why should someone do this It is important to learn how to use this PFD in the water Try your PFD in the water before attempting to use it in deep water or in an emergency to find out what position and adjustments provide the best support for you It is important especially in cold water and wave conditions to get your head out of the water as much as possible Doing this will reduce the amount of heat loss through your head see Hypothermia Pages 19 and 20 improve your ability to see around you to identify any
7. DO NOT REMOVE PRIOR TO SALE Model No 0340 OWNER S MANUAL HIGH WEARABILITY TYPE V USER ASSISTED INFLATABLE BELT PERSONAL FLOTATION DEVICE ADULT UNIVERSAL FOR PERSONS OVER 80 POUNDS 2 amp Deflated Inflated I APPROVAL CONDITIONS and CARRIAGE RE QUIREMENTS This inflatable belt is approved by the U S Coast Guard as a Type V User Assisted Personal Flotation Device PFD It is APPROVED ONLY WHEN WORN for use as a Flotation Aid Type III PFD for recreational use on calm inland waters It is not approved for water skiing or other high speed activity This inflatable was designed to be more comfortable and less restrictive to wear than inherently buoyant PFDs When used and serviced according to this owner s manual this personal flotation device PFD can greatly increase your chances of survival Not recommended for non swimmers or weak swimmers Users of inflatable PFDs must be at least 16 years of age See Page 3 for Conditions for Type V Approval WEAR YOUR PFD Most drowned victims of boating accidents owned PFDs but were not wearing them when they died Most drowning occurs in inland waters not way out at sea and most within a few feet of safety If you DO NOT intend to wear this PFD then SELECT ONE that you will Doing this provides feedback to manufacturer s as to what makes a PFD wearable SPECIFICATIONS Chest size 30 52 inches Weight range over 80 pounds Age Range 16 years and older Buoyancy
8. S Inc Call 1 800 STEARNS 1 800 783 2767 for your nearest certified Stearns Repair Facility VI WHY ARE PFDs REQUIRED SAFETY EQUIPMENT Drownings are the leading cause of fatalities involving recreational boating A PFD provides flotation to help keep your head above water help you stay face up in the water and increase your chances for survival and rescue Most adults only need an extra 7 to 12 pounds of flotation to keep their heads above water The proper size PFD will properly support the weight of the wearer This is an inflatable PFD It does not provide any flotation unless itis inflated Familiarize yourself with the use of this PFD so you know what to do when you need to use it 16 VII HOW AND WHY TO TEST YOUR PFD Inflate your PFD and try it out in the water to e Make sure it floats you Comfortably When worn properly Adequately for expected wave conditions Body shapes densities affect performance e Make sure it works A flow of bubbles should not appear See Section V for leak tests It should inflate quick and easily e Learn how it works by Activating the CO inflation system Rearming the CO inflation system Using the Oral inflator tube HOW DO YOU TEST YOUR PFD USING THE MANUAL INFLATOR 1 To test your inflatable PFD you will need e Your fully armed PFD and e Rearming kit approved for your PFD This kit contains a CO cylinder that you will need to use following this test 2 Put on the PFD
9. boating contact your state boating authority U S Coast Guard Auxiliary U S Power Squadron Red Cross or your nearest unit of the U S Coast Guard e Toll Free Boating Safety Hotline 1 800 368 5647 e To find out about free boating courses in your area call 1 800 336 BOAT in Virginia call 1 800 245 BOAT or see the USCG Boating Web Page at www uscgboating org 21 DO NOT ATTACH PFDs TO YOUR BOAT Each PFD has straps hooks buckles or other means for securing the device in place on the wearer Some PFDs also incorporate decorative Dee rings or tabs Such items are not to be used to attach the device to the boat Attaching the device to the boat will not permit it to function as intended CO PERMEATION LOSS CO gas will permeate the chamber fabric over time Oral inflation will be necessary to maintain full buoyancy BUDDY LINE INFORMATION Buddy lines when provided are to be used by people adrift in the water to attach themselves to one another and aid in staying together Buddy lines are not designed for lifting IF YOU HAVE ANY QUESTIONS ABOUT THE INITIAL ARMING REARMING REPACKING OR NEAREST CERTIFIED STEARNS REPAIR FACILITY CALL 1 800 STEARNS 1 800 783 2767 PRODUCT REGISTRATION PLEASE MAIL REGISTRATION CARD OR CALL 1 800 STEARNS 1 800 783 2767 IN ORDER TO RECEIVE IMPORTANT UPDATES ON THIS PFD BSS oe a is ae PE E print run id 22
10. ch buoyancy as a Type Ill inflatable PFD However the buoyancy that a CO cylinder provides is enough to turn many people to a stable face up position so that they can add additional buoyancy if necessary by blowing air into the chamber through the oral tube When fully inflated using both the CO cylinder and a few additional puffs of air through the oral tube the buoyancy of this PFD is equal to that of an inflatable Type III Finally this PFD is a Type V because you must know how to readjust it to float you best Wearing this PFD knowing how to achieve full buoyancy and how to maximize performance are necessary for it to provide an equivalent level of safety to PFDs without user conditions on their approval See Page 9 Maximizing Performance APPROVED ONLY WHEN WORN This PFD has the Approved Only When Worn condition on it s approval because if it is not worn whenever above deck and underway it cannot be counted as a PFD to meet the carriage requirements on your boat Wearing this PFD is intended to 1 Provide it with the extra attention associated with use and 2 Increase safety enormously because you have it on when you need it MANDATORY CARRIAGE REQUIREMENTS Federal Regulations in 33 CFR 175 1993 require you to carry Coast Guard approved personal flotation devices PFDs legibly marked with the Coast Guard approval number which are in good and serviceable condition and are the correct size for each
11. d f the cylinder cap is punctured or damaged in any way discard it and install a new undamaged cylinder in the mechanism If the cylinder is OK you must properly screw it back into the mechanism 4 Cylinder Tightness When screwing the cylinder back into the PFD make sure it is snug Over tightening can damage the inflator seal but if not snug the cylinder can unscrew during use and may leak or not be punctured when the Jerk to Inflate lanyard is pulled Additional Notes on CO Cylinders a FAILURE to properly rearm the inflation mechanism prior to installing the CO cylinder will result in a premature activation of the cylinder Follow the rearming steps exactly See Pages 11 and 12 b CO cylinders are good for one inflation and cannot be recharged c CO cylinders are made with a protective coating that may wear off after a period of use or exposure to the environment When this coating is worn off the COz2 cylinder may start to show some signs of rusting If this occurs replace the CO2 cylinder d If a gram scale such as postal scale is available it is recommended to weigh the cylinder to verify that it meets the minimum weight listed on the cylinder OTHER USE GUIDE LINES STUDY this manual and practice using your belt to become thoroughly familiar with its features and operation Your inflatable PFD will not provide buoyancy until you inflate it See Pages 17 and 18 for testing your PFD ALWAYS re
12. entially damaging elements If these defects expose the yellow chamber material discontinue use of the PFD until you have had the PFD inspected by an certified Stearns Repair Facility If these defects are noticed but the yellow chamber fabric is not exposed the Inflatable Chamber should also be checked for leaks The Inflatable Chamber should also be checked for leaks at the beginning of each season and at least every two months during the boating season The leak test procedure is described under USER S INSPECTION Refer to Pages 14 and 15 2 Examine the inflation mechanism status indicators The indicator will tell you if the inflation mechanism is properly ARMED REARMED and ready for activation If the indicator shows RED the mechanism is not ready to fire and you must rearm the mechanism to set the indicator to GREEN Refer to rearming instructions on Pages 11 and 12 and on the PFD chamber 3 Examine Your CO Cylinder The CO cylinder contains the gas charge that will inflate your PFD when the inflation mechanism is fired You must verify that the CO cylinder installed is of the correct size and has not been previously fired There are no indicators to show that the CO2 cylinder is full See the Product Specifications section on Page 2 of this manual for the proper size cylinder The size includes both thread size and gram weight To examine the cylinder you must unscrew it and visually examine the flat surface of the threaded en
13. imum needed for you to safely use this inflatable PFD Fully inflate the PFD using the oral inflator See if the PFD will float you on your back or slightly back of vertical In a relaxed floating position verify that your mouth is well above the water s surface Note the effect of where you hold your legs on how you float Get out of the water and remove the PFD Completely deflate the PFD using the oral inflator Let the PFD dry thoroughly REARM AND REPACK the PFD in accordance with the manufacturers instructions Refer to Pages 11 12 and 13 18 VIII WEAR YOUR PFD In approximately 80 percent of all boating fatalities the victims were not wearing a PFD Most fatal accidents happen on calm sunny days This inflatable PFD is much more comfortable to wear than other PFD types Get into the habit of wearing this PFD Non swimmers and children especially should wear a hybrid or non inflatable PFD at all times when on or near the water IX HYPOTHERMIA Prolonged exposure to cold water causes a condition known as hypothermia a substantial loss of body heat which leads to exhaustion and unconsciousness Most drowning victims first suffer from hypothermia The following chart shows the effects of hypothermia Unconsciousness of Survival 32 5 UNDER 15 MIN lt 15 TO 45 MIN 0 3 TO 4 4 32 5 to 40 15 TO 30 MIN 30 TO 90 MIN 44TO 10 40 to 50 30 TO 60 MIN 1 TO 3 HOURS 10 TO 15 6 50 to 60 1 TO 2 HOURS 1 TO 6 HOURS 15 6
14. ion and repair or discard the PFD 3 Function Test of Oral Valve With the PFD inflated remove the dust protection cap and test the valve by pushing it down using the tab provided on the cap refer to Page 10 The valve should depress easily and when depressed air should escape When released the valve should automatically return to the closed position and reseal REARMING KIT S Use replacement kit no 0925 See Rearming Instructions on pages 11 and 12 CARE AND CLEANING INSTRUCTIONS Drying If the device is wet place on a coat hanger to allow thorough drying Do not place in direct sunlight to dry Do not use any heat source or place on radiator Cleaning Damp wipe only with mild detergent recommended for synthetic fabrics Remove grease and oil immediately After every use rinse well with fresh water Read instructions provided on the device e DO NOT MACHINE WASH e DO NOT MACHINE DRY e DO NOT DRY CLEAN e DO NOT USE SOLVENT BASED CLEANERS e DO NOT BLEACH Revised 2006 05 08 15 STORAGE e Store in clean cool dry area e Do not store in direct sunlight REPAIR If you have any question about the condition or integrity of this product call 1 800 STEARNS 1 800 783 2767 A damaged device must be repaired by certified Stearns Repair Facility or discarded SERVICING Stearns strongly recommends that this device be inspected at least every 24 months by a certified Stearns Repair Facility or STEARN
15. knees together will also help to conserve body heat Keep a positive attitude about your survival and rescue This will improve your chances of extending your survival time until rescued Your will to live does make a difference If there is more than one person in the water huddling is recommended while waiting to be rescued This action tends to reduce the rate of heat loss and thus increase the survival time 20 X EACH OF THESE DEVICES IS INTENDED TO HELP YOU SAVE YOUR OWN LIFE For your PFD to function properly follow these suggestions to verify that it fits floats and remains in good condition 1 Check the CO cylinder inflation mechanism status indicator before each use 2 Get in the habit of rearming the inflation mechanism immediately after each CO2 inflation 3 Be sure your CO cylinder is screwed in tight Try your wearable PFD on and adjust it until it fits comfortably in and out of the water Mark your PFD with your name if you are the only wearer Do not alter your PFD If it doesn t fit properly get one that does An altered device is no longer Coast Guard approved Your PFD is not intended for use as a fender or kneeling pad If your PFD is wet allow it to dry thoroughly before storing it Store it in a well ventilated area 9 Do not dry your PFD in front of a radiator or other source of direct heat XI ADDITIONAL INFORMATION If you need more information about PFDs and safe recreational
16. not close 10 REARMING INSTRUCTIONS STEP 1 Unscrew used CO cylinder in a counterclockwise direction and immediately discard Do not insert new cylinder at this time To avoid confusion later in the rearming process we Fiag suggest you throw away the EF old CO cylinder now wee STEP 2 Close manual inflator arm within inflator body and carefully insert a new green indicator tab so that it fully covers the red semi circle on the body STEP 3 Look into threaded cylinder receiver and view the gasket If worn contact Stearns Inc 1 800 STEARNS for the nearest certified Stearns Repair Facility 11 REARMING INSTRUCTIONS cont Step 4 Inspect the face of the new cylinder Be sure it is smooth and has no holes or scratches There is a gross weight on the cylinder If you have any questions about cylinder integrity weigh the cylinder on a small scale such as a postage scale Compare the weight printed on the cylinder to the actual weight If they do not match get another cylinder STEP 5 Screw new cylinder in a clockwise direction firmly into the inflator Do not over tighten but ensure the fit is tight STEP 6 Check the inflator arming indicator every boating trip The indicator and cylinder tightness tell you if there is a need for service Check the cylinder face regularly to ensure it is not punctured Be sure cylinder is screwed in tight 12 REPACKING INSTRUCTIONS Al
17. son that you must follow the care and cleaning instructions and perform the maintenance and service checks This will assure that the PFD remains functional and will maximize the useful life of this PFD Failure to follow these instructions rigorously could result in a non functioning PFD causing injury or death USER S INSPECTION The users should perform the following checks before each season or before a long journey or before each outing as recommended below 1 Physical Inspection of Cover and Straps Examine outer shell fabric seams webbing attachments buckles slides etc Fabric fading can indicate a loss of strength Check for strength by pulling seams and attachments snugly If device shows any signs of damage return to a certified Stearns Repair Facility or replace the entire device This inspection should be performed each outing 14 2 Oral Inflation Leak Test This test should be performed every two months and at the start of each season Inflate buoyancy chamber using the oral inflation valve and leave to rest for 16 hours When buoyancy chamber remains firm and full of air there is no leakage and chamber is operational If the chamber deflates during this leak test it is no longer in operational condition and should not be used Some types of leaks can be repaired by a certified Stearns Repair Facility while others are not repairable If the PFD leaks either return to certified Stearns Repair Facility for evaluat
18. sources of rescue and to keep your mouth out of the water as much as possible to reduce the chance of inhaling water Most but perhaps not all people will be able to get their heads completely out of the water by placing their bodies in a near vertical position and float with their arms extended out over the top of the chamber see figure 1 below Once in the water with the PFD inflated you should be able to float comfortably on your back see figure 2 below You may find it more comfortable to loosen the body strap slightly without unbuckling it and let it slide up to your chest Then orally add more air to the chamber if necessary and readjust the neck strap to provide head support You may find that positioning the neck strap in various locations on your neck or even the back of your head will provide better head support DEFLATION INSTRUCTIONS Deflating may be accomplished by inserting the deflation tool located on the dust cap into the end of the oral inflation tube while gently squeezing the inflation chamber Reposition the dust cap over the end of the inflation tube after deflating to help protect the valve inside INVERT DEPRESS TO DEFLATE DO NOT TWIST OR WRING INFLATABLE CHAMBER TO DEFLATE If for any reason the oral valve remains open depress it several times If it does not release discontinue use of this PFD and return to Stearns Inc for repair In an emergency situation hold thumb over the valve if it will
19. ways dry out deflate the PFD and rearm the inflation mechanism Follow REARMING instructions prior to REPACKAGING Postion as shown in Fig i Reference General Armangements on Page 2 iFig 1 STEP 2 Rel up tee ar chambas on top of the neck Strap yeh mieto mechanishn remeng or i Pg 2 STEP 3 einer ling he ctor ready a Saus Indicator to be wsie through fu vino Fig 3 STEP A Be sure to leave the Jerk bo Inflate tab exposed at Brea bottan of thee bet Fig 4 13 IV IS YOURPFD IN GOOD AND SERVICEABLE CONDITION Check your PFD between outings to be sure that it is properly armed that it is free of rips tears or holes that all seams are securely sewn and that the fabric straps and hardware are still strong Check to be sure your cylinder is screwed in tight Inspect the inflatable portion of the PFD in accordance with Care and Maintenance Instructions V CARE AND MAINTENANCE INSTRUCTIONS GENERAL PRODUCT LIFE EXPECTANCY The reliability and service life of this PFD depends greatly upon how it is used and cared for Avoid storing PFD in direct sunlight Sunlight contains ultraviolet radiation that weakens synthetic materials Prolonged exposures to high temperatures and high humidity may shorten service life of this PFD While it is known that these elements degrade the materials every use environment is unique so there is no sure way to estimate how long the PFD will last It is for this rea
Download Pdf Manuals
Related Search