GRAFIK Eye QS Wired with EcoSystem
Contents
1. Start and End afterhours mode Enable and Disable daylighting for all zones groups Enable and Disable occupancy for occupancy vacancy sensors Enable and Disable occupied events for all occupancy sensors System Communications and Capacities Low voltage type IEC PELV NECe Class 2 wiring connects control units wallstations motorized shades and control interfaces A QS system can have up to 100 devices and 100 zones Class 1 Class 2 wiring connects ballast to control unit Infrared Infrared IR receiver allows infrared transmitters to select 8 scenes raise lower lighting zones or raise lower shades Transmitter buttons imitate buttons on faceplate e 50 ft 15 m line of sight range Terminal block infrared input for connection to a wired IR input from third party equipment e IR can be disabled via programming Works with Lutron GRX IT and GRX 8IT infrared remote controls Page 5_ Job Number JOOS o oo GRAFIK Eye QS Specifications Accessory Controls seeTouche QS Wallstations QSWS2 Wired seeTouche QS keypads provide the following features Access to one or more of the 16 scenes on the GRAFIK Eyee QS control unit Zone toggle partitioning sequencing fine tune panic mode and timeclock enable disable Contact closure inputs Various other functions that are available on specific wallstation configurations Refer to the seeTouch specification submittal Accessory Controls QS Senso2. Wire Sizes check compatibility in your area QS Link Wiring Length Lutron Cable Part Number Less than 500 ft 153 m Power terminals 1 and 2 1 pair 18 AWG 1 0 mm GRX CBL 346S non plenum GRX PCBL 346S plenum Data terminals 3 and 4 1 twisted shielded pair 22 AWG 0 5 mm 500 to 2000 ft Power terminals 1 and 2 153 to 610 m 1 pair 12 AWG 4 0 mm GRX CBL 46L non plenum Data terminals 3 and 4 GRX PCBL 46L plenum 1 twisted shielded pair 22 AWG 0 5 mm Daisy Chain Wiring Example GRAFIK Eyee QS Control Unit seeTouche QS Sivoiae QS wallstations Shade ma I ears a a fa Ie FS Sivoiae QS smart panel T Tap Wiring Example GRAFIK Eyee QS seeTouche QS Control Unit ao wallstations EIA _ Sivoiae QS f smart panel Sivoiae QS Shade mae m 6g LUTRON SPECIFICATION SUBMITTAL Page 16 Model Numbers Job Numbers GRAFIK Eye QS Control Unit with EcoSysteme Preset Dimming Controls Mounting Mount
3. Number of Line Voltage Outputs 3 Zones 1 3 on e o Yes iPod is a trademark of Apple Inc registered in the United States and other countries LUTRON SPECIFICATION SUBMITTAL Paget Model Numbers Job Numbers GRAFIK Eye QS Control Unit with EcoSysteme Preset Dimming Controls 369310 Rev B 2 11 17 11 Mechanical Dimensions le 9 in 239 mm wins eoo 10 mm a 2n 51 mm ry TP 4 e in 119 mm Lo O je i L a ZIA 1 e9 Front View Side View Fits into a 4 gang U S backbox 3 in 89 mm deep Lutron P N 241 400 System Topology Example of Wired System Wired QS link GRAFIK Eye QS GRAFIK Eyee QS SA wireless wireless C z Solas QS foal aS Si SE CI NWK E oqdule Guanine seeTouche QS seeTouche Q optional Qs EcoSysteme Wired ballast occupancy Energi Savr sensor Nodem sLUTRON SPECIFICATION SUBMITTAL Page 2 Model Numbers Job Numbers GRAFIK Eye QS Control Unit with EcoSysteme Preset Dimming Controls 369310 Rev B 3 11 17 11 Features Pushbutton recall of four preset lighting scenes plus Off Twelve 12 additional scenes accessible through
4. QS Link Lutron PN 369405 Faceplate is hinged at the top and bottom and stays open at 180 for ease of access Direct control of 120 V and 277 VN EcoSysteme Hi lume 3D and Hi lumee LED ballasts no interface required Scene and Shade Buttons Large rounded buttons are easy to use Backlit buttons with optional engraving make it easy to find and to operate the control unit in low light conditions backlight can be disabled Optional button engraving is angled up to the eye for easy reading Predefined label stickers are included for field labeling 4 preset lighting scenes plus Off are accessible from the front of the control unit 12 additional scenes are stored in the control unit and are accessible from seeTouche QS wallstations and QS interfaces Light levels fade smoothly between scenes Fade time can be set differently for each scene O to 59 seconds or 1 to 60 minutes Maximum fade time from Off is 3 seconds Page 4 Job Numbers GRAFIK Eye QS Specifications Shade Control The GRAFIK Eyee QS control unit can include up to 3 shade button columns Each column has backlit open preset close and raise lower buttons Each shade button column can be programmed to operate one shade or a group of shades Shades may be assigned to more than one shade button column Faceplates are available with 1 2 and 3 shade button columns Zone Control Each zone has a dedicated raise and lower button
5. Zone Infrared Lighting Info replaces the need for a handheld programmer shade control receiver control screen C PDA CLR does not communicate with control keypad GRAFIK Eyee QS with EcoSysteme keypad Backlit buttons with engraving make unit easy to locate and operate e Available in a variety of colors and finishes Note General Engraving EGN shown C Open H TO Preset A Close i 1 VIE O LUTRON SPECIFICATION SUBMITTAL Page 3 Model Numbers Job Numbers GRAFIK Eye QS Specifications Input Power 120 127 V 50 60 Hz 220 240 V 50 60 Hz Listings 120 127 V UL CSA NOM CEC Title 24 Environment 32 to 104 F O to 40 C Relative humidity less than 90 non condensing Lighting Sources Load Types EcoSysteme Hi lume 3D and Hi lumee LED ballasts available on all zones Zones 1 2 and 3 control the following lighting sources with a smooth continuous square law dimming curve or on a full conduction non dim basis Incandescent Halogen Magnetic low voltage transformer Lutron Tu Wiree electronic fluorescent dimming ballast Advance Mark X electronic
6. requires more than 50 mA The CCl is capable of operating in the following modes Occupancy If an occupancy sensor is wired directly to the GRAFIK Eyee QS control unit Emergency This setting allows the GRAFIK Eye QS control unit to work with a LUT ELI When an emergency situation is detected all lights will go to full on and no operations will be allowed until the emergency signal is cleared Afterhours Allows the CCI to start and end the afterhours mode Timeclock Allows the CCI to enable and disable the timeclock Scene Lockout Prevents the user from making any changes to the control unit The current scene will stay on until the CCI enables normal operation Save Never Prevents any changes from being saved while the CCI is being used Disable CCl The CCI will have no effect on the system and will not appear on the list of available sensors Security Lockout Password A 4 digit password using characters A to Z and O to 9 can be enabled disabled to lock out access to the Programming Menu By default there is no password enabled on the GRAFIK Eyee QS control unit e f case the 4 digit password is forgotten contact Lutron Technical Support to regain access Page 7_ JobNumberss GRAFIK Eye QS Control Unit with EcoSysteme Preset Dimming Controls 369310 Rev B 8 11 17 11 Capacities T SSCS Mu GE Gik TES Load Type Notes Zones 1 2 and 3 e All electronic low voltage ELV lightin
7. Color Combinations page for faceplate stripe and button colors Base Unit Example QSGR _E QSGR 6E 6 zone base unit and QSGFP 2IV EGN Ivory faceplate kit with two shade columns and general a Prefix EcoSysteme engraving Faceplate Kit includes coordinating stripe and buttons I l Faceplate Top Color Keypad Prefix Door Finish Engraving Color Code Omit same as unit T Translucent Faceplate Custom Color Finish Codes Keypad Engraving Codes Architectural Matte Architectural Metal Satin Color Matte Omit Unengraved Finishes Finishes Finishes Ships with engraving certificate that Standard Bright Brass BB Sey Sw customer can redeem at no charge ship in 48 hours Bright Chrome BC Biscuit BI EGN General Engraving White WH Bright Nickel BN Eggshell ES of e Open lvory IV Satin Brass SB Taupe Te lt 2 Preca Beige BE Satin Chrome SC Midnight MN a e Close Gray GR Satin Nickel SN Limestone LS SIA Brown BR Antique Brass QB Stone ST Black BL Antique Bronze QZ Desert Stone DS ott Shade Almond AL Terracotta TC Lighting column Light Almond LA Anodized Aluminum Hot HT keypad Gold GS Ses oldstone Finishes Pedin PD NST Non Standard Text Engraving Clear CLA Plum PL Please visit the GRAFIK Eyee QS website Black BLA Turquoise T
8. GRAFIK Eye QS Control Unit with EcoSysteme Preset Dimming Controls 369310 Rev B 1 11 17 11 GRAFIK Eyes QS Control Unit with EcoSysteme Description GRAFIK Eyee QS with EcoSysteme is the premier energy saving lighting and shade control The GRAFIK Eyee QS control unit features an astronomic timeclock and intuitive lighting presets which are seamlessly integrated with EcoSysteme fluorescent ballasts and LED drivers Maal O p p and Lutron s QS components and systems Additionally the GRAFIK Eyee QS with EcoSysteme control unit is TIA E compatible with all Lutron wired QS products and systems pa including Quantume Application Suggestions and Differences between GRAFIK Eyee QS with EcoSysteme and Standard EcoSysteme Bus Supply GRAFIK Eyee QS with Energi Savr Nodem EcoSysteme with EcoSysteme Suggested Recommended Applications Single rooms partitioned spaces Open spaces multiple e g conference room classroom enclosed rooms e g open ballroom lobby office window offices Programming Method Info Screen on the QS control unit Via Energi Savr Nodem App for icine Integral Timecock Yes CT O Compatible with EcoSysteme Wall Conros no e SCSC d Compatible with EcoSysteme R Sensors no o o o o o o ooo o i fS or Security Systems
9. Q at www lutron com grafikeyeqs Brass BRA e BG for custom engraving forms Submit S CESS SG completed form with order and unit will Greanlaner GB ship engraved as specified by customer Sienna Sl Merlot MR Mocha Stone MS sLUTRON SPECIFICATION SUBMITTAL Page 9 Model Numbers Job Numbers JOOS O oo GRAFIK Eye QS Control Unit with EcoSysteme Preset Dimming Controls 369310 Rev B 10 11 17 11 GRAFIK Eyes QS with EcoSysteme Control Unit Custom Options and Model Numbers See previous page for Custom Model Numbers See Standard Color Combinations page for faceplate stripe and button colors Custom Button Kit QSGB 5B WH I I Custom Button Button Button Keypad Kit Prefix Configuration Color Engraving Finish Code 3BRL 8 button with raise lower shade column 5B 5 button lighting keypad Keypad Engraving Codes Omit Unengraved Ships with engraving certificate that Button Kit Custom customer can redeem at no charge Color Finish Codes EGN General Engraving Architectural Matte Satin Color Matte A Open F Finishes Finishes 2 Preset White WH Snow sw 23 e Close Ivory IV Biscuit BI 4 ZIS o ae Eggshell ES gt Off Shade ray Taupe TP Sai BR p Lighting column Black BL keypad Almond AL NST Non Stan
10. bottom gray stripe and white buttons Suffix Faceplate F Stripe S Button B Suffix Faceplate F Stripe S Button B Architectural Matte Satin Matte WH White Gray White MN Midnight Gray Black IV Ivory Beige Ivory TP Taupe Gray Taupe BE Beige Ivory Beige SW Snow Gray Snow GR Gray Black Gray ES Eggshell Beige Eggshell BR Brown Black Brown BI Biscuit Eggshell Biscuit BL Black Gray Black LS Limestone Gray Gray AL Almond Light Almond Almond ST Stone Gray Gray LA Light Almond Almond Light Almond DS Desert Stone Taupe Taupe Architectural Metal TC Terracotta Taupe Taupe BB Bright Brass Black Black BG Bluestone Gray Gray BC Bright Chrome Black Black HT Hot Taupe Taupe BN Bright Nickel Black Black MR Merlot Taupe Taupe SB Satin Brass Black Black Sl Sienna Brown Brown SC Satin Chrome Black Black GB Greenbriar Gray Gray SN Satin Nickel Black Black SG Sea Glass Gray Gray QB Antique Brass Black Black MS Mocha Stone Taupe Taupe QZ Antique Bronze Black Black GS Goldstone Ivory Ivory Anodized PD Palladium Gray Gray CLA Clear Black Black PL Plum Taupe Taupe BLA Black Black Black TQ Turquoise Gray Gray BRA Brass Black Black ssLUTRON SPECIFICATION SUBMITTAL Page 11 Model Numbers Job Numbers GRAFIK Eye QS Control Unit with EcoSysteme Preset Dimming Controls 369310 Rev B 12 11 17 11 Overview Terminations Load wiring EcoSysteme bus E1 E2 Communication link Occupa
11. dard Text Engraving Ligi Amone LA Please visit the GRAFIK Eyee QS website at www lutron com grafikeyeqs for custom engraving forms Submit completed form with order and unit will ship engraved as specified by customer Custom Stripe Kit QSGS WH Stripe Stripe Color Kit Finish Prefix Stripe Custom Color Finish Codes Same as Faceplate colors on previous page LUTRON SPECIFICATION SUBMITTAL Page 10 Model Numbers Job Numbers GRAFIK Eye QS Control Unit with EcoSysteme Preset Dimming Controls 369310 Rev B 11 11 17 11 GRAFIK Eyes QS with EcoSysteme Control Unit Standard Color Combinations See previous pages for Custom Model Numbers Faceplate is comprised of a top and bottom The bottom will always be the color indicated F faceplate under faceplate The top may be the same color or translucent Use the chart for faceplates that have the same color top and bottom If a translucent lid is chosen the stripe will automatically be the same color as t S stripe Open i O 1 the bottom lid Preset 2 __B buttons Close Ee Example VIS F faceplate If you order QSGR 6E 1WH your GRAFIK Eyee QS control unit with 6 lighting zones and 1 shade column will come with a white faceplate both top and
12. dimming ballast Neon and cold cathode Non dim incandescent magnetic low voltage Tu Wiree or neon cold cathode Cree LR4 6 120 V fixtures for loading capacities please refer to the LED report card located at www lutron com LEDtool Please refer to Capacities for more information Zones 1 2 and 3 control the following lighting sources with a smooth continuous square law dimming curve or on a full conduction non dim basis through separate Lutron power modules e Electronic low voltage transformer e Lutron Hi lumee Eco 10 and Compact SEr electronic fluorescent dimming ballast e Non dim e0 10V s LUTRON SPECIFICATION SUBMITTAL Model Numbers Control Unit with EcoSysteme Preset Dimming Controls 369310 Rev B 4 11 17 11 Key Design Features e Lightning strike protection meets ANSI IEEE standard 62 41 1980 Can withstand voltage surges of up to 6000 V and current surges of up to 3000 A e Tested to withstand 16 kV electrostatic discharge without damage or memory loss e RTISStw equipped Compensates in real time for incoming line voltage variations no visible flicker with 2 change in RMS voltage per cycle and 2 Hz change in frequency per second e Power failure memory retains programming and light level settings for up to 10 years in the event of a power loss The GRAFIK Eye QS supplies 3 Power Draw Units PDUs on the QS link For complete information see Power Draw Units on the
13. e or more zones to a preset level and off Shade Output mode A Shade Column on the GRAFIK Eyee QS control unit can be linked to control outputs 1 3 and or outputs 4 5 on the QSE IO s LUTRON SPECIFICATION SUBMITTAL Model Numbers Control Unit with EcoSysteme Preset Dimming Controls 369310 Rev B 6 11 17 11 Accessory Controls DMX Output Interface QSE CI DMX Any zone on the GRAFIK Eyee QS control unit can be mapped to any single DMX512 Channel Any zone on the GRAFIK Eyee QS control unit can be simultaneously mapped to any three DMX512 channels providing RGB CMY control DMX loads cannot be used with daylighting Accessory Controls Ethernet and RS232 Interface QSE CI NWK E Allows for monitoring and control of the outputs and local scenes of the GRAFIK Eye QS control unit Accessory Controls QS Keyswitch Wallstations QSWS2 KS Recalls preset light levels for any two scenes including Off Allows fine tuning raise lower level of a zone or group of zones Starts Stops scene sequencing Scenes 1 4 or Scenes 5 16 Enables Disables Timeclock Enables Disables occupancy sensors Enables Disabled daylight sensors Allows toggle of Zone s to a preset level and off Enables Disables panic mode Starts Stops afterhours mode Other Accessory Controls and Devices Energi Savr Nodem QS ESN See the SPecification SUbmittal for complete details Occupancy Sensor s The GRAFIK Eyee QS control unit works w
14. g used with an interface must be rated for reverse phase control dimming Before installing an ELV light source verify with the manufacturer that their transformer can be dimmed When dimming an ELV interface such as the PHPM PA DV WH must be used with the control unit e Not all zones must be connected however connected zones must have a minimum load as specified above e Maximum total lighting load for a magnetic low voltage MLV varies by input voltage 120 127 V 800 VA 600 W 220 240 V 1200 VA 960 W e Maximum total lighting load for Lutron Tu Wirew and Advance Mark Xe electronic dimming ballasts 120 to 127 V only must not exceed 6 A per zone or 16 A per unit e No zone may be loaded with more than the capacity specified above For higher wattage applications or for 277 V applications use Lutron power module PHPM PA PHPM WBX PHPM PA DV PHPM SW or PHPM WBX DV e For controlling low wattage loads CFL LED in a non dim application contact Lutron Technical Support for the appropriate solution System Limits e The QS wired communication link is limited to 100 devices or 100 zones LUTRON SPECIFICATION SUBMITTAL Pages Model Numbers Job Numbers OOOO O S O oO GRAFIK Eye QS Control Unit with EcoSysteme Preset Dimming Controls 369310 Rev B 9 11 17 11 GRAFIK Eyes QS with EcoSysteme Control Unit Custom Color Options and Model Numbers You must order a Base Unit and a Faceplate Kit See Standard
15. ing screws 4 GRAFIK Eyee QS with EcoSysteme control unit Hinged bottom lid s LUTRON SPECIFICATION SUBMITTAL Model Numbers 369310 Rev B 17 11 17 11 Standard 4 gang U S wallbox 3 in 89 mm deep available from Lutron P N 241 400 Page 17 Job Numbers
16. ith occupancy sensors through either Scene Control Up to four sensors activate user selectable occupancy and vacancy scenes Zone Control Up to four sensors per zone activate user selected occupancy and vacancy zone levels Occupancy sensors may include Contact closure sensors wired to CCI input on back of GRAFIK Eyee QS control unit Wired or wireless sensors connected QS Sensor Module QSM If any sensor in a group detects occupancy then the GRAFIK Eyee QS control unit will go to the designated occupancy scene or zone level If all sensors in a group detect vacancy then the GRAFIK Eyee QS control unit will go to the designated vacancy scene or zone level Pagele Job Number OOOO o o GRAFIK Eye QS Specifications Daylight Sensor s The GRAFIK Eyee QS with EcoSysteme control unit works with compatible daylight sensors to adjust electric light levels based on measured daylight levels Sensors can be configured to control either GRAFIK Eyee QS zones or groups of EcoSysteme loads independent of zoning Daylight sensors may include Wired sensors connected to EcoSysteme ballasts or interfaces Wired or wireless sensors connected to a QS sensor module QSM In Zone Mode a daylight sensor can control one or more GRAFIK Eyee QS zones Each zone can be calibrated to target light levels A zone can be controlled by no more than one daylight sensor In Group Mode a daylight sensor can contr
17. ncy sensor contact closure input a and 24 V power eni lez z HEHHE input Power wiring Ty Maximum EcoSysteme Wire Gauge Bus Length 12 AWG 4 0 mm 2200 ft 671 m 14 AWG 2 5 mm 1400 ft 427 m 16 AWG 1 5 mm 900 ft 275 m 18 AWG 1 0 mm 570 ft 175 m sLUTRON SPECIFICATION SUBMITTAL Page 12 Model Numbers Job Numbers GRAFIK Eye QS Control Unit with EcoSysteme Power Group Wiring Example Preset Dimming Controls 369310 Rev B 13 11 17 11 On the QS link there are devices that supply power and devices that consume power Each device has a specific number of Power Draw Units PDUs it either supplies or consumes A Power Group consists of one device that supplies power and one or more devices that consume power each Power Group may have only one power supplying device Refer to the QS Link Power Draw Units specification submittal Lutron PN 369405 for more information concerning PDUs Within Power Groups on the QS link connect all 4 terminals 1 2 3 and 4 shown by the letter A in the diagram Between devices on the QS link that supply power connect only terminals 1 3 and 4 NOT terminal 2 shown by the letter B on the diagram Wiring can be T tapped or daisy chained 2 emm aa E GRAFIK Eyee QS control unit Supplies PDUs H Control Interfaces Wallstati Consume PDUs aaRS Do not connect Consume PDUs
18. ol one or more EcoSysteme loads regardless of how they are zoned on the GRAFIK Eyee QS control unit A group can be controlled by a single daylight sensor Each group can be calibrated to independent target light levels Up to 16 groups are available Daylight control can be enabled or disabled on a scene by scene basis By default daylight control is enabled in all scenes Note Daylight control through the GRAFIK Eyee QS control unit only affects lighting loads Shade groups cannot be controlled by daylight sensors Daylighting does not affect DMX or RGB CMY DMX loads X LUTRON SPECIFICATION SUBMITTAL Job Name Control Unit with EcoSysteme Model Numbers Preset Dimming Controls 369310 Rev B 7 11 17 11 Contact Closure Input CCI with Power Supply Output e Each GRAFIK Eyee QS control unit has one contact closure input Terminal A The attached device must provide a dry contact closure or solid state output Input is miswire protected up to 36 V The contact closure is capable of accepting the following types of inputs Maintained default The GRAFIK Eyee QS control unit will act on both a contact closure and a contact open release event Momentary The GRAFIK Eyee QS control unit will act on only contact closure events Each GRAFIK Eyee QS control unit can supply 50 mA maximum at 24 V Useful for powering occupancy sensors An auxiliary power supply must be used if the device
19. on panel and to light fixtures e Each line voltage terminal can accept one 12 AWG 2 5 mm wire e Consult Lutron for non dim relay wiring and or load side emergency transfer wiring sLUTRON SPECIFICATION SUBMITTAL Page 14 Model Numbers Job Numbers GRAFIK Eye QS Control Unit with EcoSysteme Preset Dimming Controls 369310 Rev B 15 11 17 11 EcoSystemes Bus Wiring EcoSysteme Bus Link Terminal Detail jena ezel EE HEHEHEHEHE aie 5l E2 E EcoSysteme E2 ballasts Yd E1 vy To additional EcoSysteme ballasts EcoSysteme Bus Wiring Example To additional ballasts and modules up to 64 total EcoSysteme Bus EcoSysteme d EcoSysteme Eco 10e or EcoSysteme EcoSysteme Ballast Module Hi Lumee Ballast Ballast GRAFIK Eyee QS Ballast with EcoSysteme limit one per Daylight Sensor EcoSysteme link Occupancy Sensor ssLUTRON SPECIFICATION SUBMITTAL Page 15 Model Numbers Job Numbers OOOO o oo GRAFIK Eye QS Control Unit with EcoSysteme Preset Dimming Controls 369310 Rev B 16 11 17 11 IEC PELV NECe Class 2 QS System Wiring e Wiring can be daisy chained or T tapped e Wiring must be run separately from line mains voltage e Total length of control link must not exceed 2000 ft 610 m
20. other QS devices such as seeTouche QS wallstations opn E O p e Zones 1 2 and 3 can control many light source Te types directly and others using power modules x e Optional integrated shade control buttons which or can also be added to the unit after installation e Master override buttons to raise and lower all lights Allows setup of lighting scenes and shade presets using buttons on the control unit Built in infrared IR receiver External IR connection Built in astronomic timeclock Info screen shows zone light level percentage T energy savings zone labeling programming and EcoSysteme setup Lockout option prevents accidental changes One occupancy sensor input and 24 V power for occupancy sensor QS communication link for seamless integration of lights motorized window treatments occupancy sensors wallstations and integration interfaces Compatible with all Lutron QS system components Control up to 6 8 or 16 EcoSysteme zones from internal bus supply USB Zones 1 2 and 3 are integral line voltage dimming type zones and can be optionally programmed as mini B EcoSysteme zones Up to 64 EcoSysteme or Hi lumee 3D ballasts can be addressed and grouped to zones Integral EcoSysteme setup and programming Optional
21. r Module QSM2 The QS Sensor Module provides a means to link wired or wireless occupancy and daylight sensors to a GRAFIK Eyee QS control unit via the wired QS link Occupancy sensors wired or wirelessly linked to a QS Sensor Module can be used by one or more GRAFIK Eyee QS control units on the wired link Daylight sensors wired or wirelessly linked to a QS Sensor Module can be used by one or more GRAFIK Eyee QS control units on the wired link Infrared sensors can control either one or more zones or scenes on the GRAFIK Eyee QS control unit Functionality varies refer to the documentation for the QS Sensor Module for details Picoe wireless controls wirelessly linked to a QS Sensor Module can be used to control one or more zones or scenes on the GRAFIK Eyee QS control unit Accessory Controls Contact Closure Input Output Interface QSE IO Recalls preset light levels for the following set of scenes on the GRAFIK Eyee QS control unit Scenes 1 4 and Off Scenes 9 12 and Off Scenes 5 8 and Off Scenes 13 16 and Off Sequence scenes 5 16 Enable Disable Zone Lockout Enable Disable Scene Lockout Enable Disable Panic Mode Enable Disable Timeclock Occupancy Sensors An individual input counts as 1 occupancy sensor for the GRAFIK Eyee QS control unit Each input can be assigned to either Scene Control or Zone Control please refer to the Occupancy Sensor s section of this guide Zone Toggle Allows an input to toggle on
22. terminal 2 24 V MT BO Bl Wallstations Consume PDUs Energi Savr Nodem QS unit Supplies PDUs Do not connect terminal 2 24 V U A QS Power Supply Supplies PDUs Control Interfaces Wallstatic Consume PDUs aaa Consume PDUs Do not connect terminal 2 24 V Quantum panel Supplies PDUs zs LUTRON SPECIFICATION SUBMITTAL Job Name Model Numbers Power Group 1 A Connect all 4 terminals within a power group 1 Common seme 2 24 V Power Group 2 3 and 4 Data Connect only 3 terminals between power groups 1 Common 3 and 4 Data Do not connect Terminal 2 24 V BO Power Group 3 RAN Wireless Occupancy Sensor does not consume PDUs Sa ee QS Sensor Module with wired Occupancy Sensor Consumes PDUs v Page Job Number O GRAFIK Eye QS Line Voltage Wiring Control Unit with EcoSysteme Preset Dimming Controls 369310 Rev B 14 11 17 11 Do not use eae Rear of GRAFIK Eyee QS control unit To Load 1 To Load 2 Line voltage hot live ae is labeled L Loads 1 2 3 120 127 V or 120 127 V 220 240 V or 220 240 V Distribution Panel e Pull power wiring from distributi
23. to adjust the zone Each zone has a dedicated 7 LED bar graph for level status Percentage of light level and energy saved is displayed on the info screen All zone information has blue backlit LEDs Backlight turns off when idle for 30 seconds Info Screen OLED organic LED screen is viewable from all angles Screen turns off when idle for 30 seconds Programmable zone labels Programmable scene labels Programmable timeclock schedules Programmable shade labels sLUTRON SPECIFICATION SUBMITTAL Model Numbers Control Unit with EcoSysteme Status of real time zone percentage and energy savings Preset Dimming Controls 369310 Rev B 5 11 17 11 Astronomic Timeclock e Integral to all units e 7 daily schedules available e One available holiday schedule is programmable by date up to one year in advance e 25 events per day maximum e Timeclock events are programmable to control scenes that affect any Energi Savr Nodem QS unit connected on the QS link without changing the local scene on the GRAFIK Eyee QS control unit Astronomic times are programmable by integral city database or by entering latitude and longitude Times automatically adjust throughout the year based on location Automatically adjusts for Daylight Saving Time DST adjusted for the new dates DST is programmable Local timeclock events can activate any of the following features Scenes 1 to 16 and Off Any available shade presets
Download Pdf Manuals
Related Search