NVR and Hybrid DVR Systems Setup Guide
Contents
1. YES The LAN and PoE power to the camera is probably OK NO Check the LAN cable Ethernet signal and power at the camera If faulty correct the problem and recheck the video streaming Reset the camera See Appendix B Camera reset Check the camera lens for blockages dirt etc and clean if needed Use the BNC adapter with the BLK IPD102 camera or the LOOP connector with the BLK IPS101 camera to check video If video is good but still can t connect replace the camera Everything is hooked up and working but the video that is recorded is jerky and not smooth Is there something wrong with my system Smoothness of recorded video is dependent upon several factors including compression level capture size and the maximum frame rate of your recorder Most NVR hDVRs record at frame rates of 30 90 or 120 frames per second fps The frame rate of your NVR hDVR is divided between each channel being recorded For example a 90 fps DVR recording 4 channels will record 22 5 fps per channel which will appear very smooth A 120 fps NVR hDVR recording 9 channels will record 13 fps which will appear less smooth and fluid particularly when compared to a TV broadcast at 29 97 fps If there are irregular gaps in the video or a momentary loss of video there could be problems in the system Call Supercircuits at 1 800 335 9777 for assistance Why can t I get a good picture from one of my cameras The camera s power light is blinking or fl2. 00 13 23 04 22 46 7 In the IP Details window do the following a Inthe Name field change the entry to a descriptive name for the camera In the example above the Name field contains the default name for SC Black cameras Black H264 20 www sc black com SECTION 3 SYSTEM SETUP Sp b Inthe User Name and Password fields enter the user name and password of a user with administrative access to that device c Inthe Channel No field select 1 from the pull down list for stand alone IP cameras If the device you are adding is an IP converter encoder with multiple channels for analog cameras select the converter channel number of the analog camera you want to see For example if the analog camera is attached to converter channel 3 select 3 from the pull down list d Ifthe device you are adding supports Stream on Motion PTZ IP Audio or Analog Audio click the appropriate checkbox to select it e Click Finish 8 Inthe Config Preferences Camera tab click the IP Camera Settings dropdown list and select the Name of the camera you configured in the IP Device Details window Camera Network Sensor Contral PTZ Color Display FPS Resolution Schedule System Select Camera TE 20 C Gh E ED De Ds O DD Ds EM AED Cs CE GEN I Security Screen Mode I Watch Mode IP Camera Settings Black 254 z Add Et Dee r arene Loss Sensitivity
3. or 4 Connectors on the 4 channel audio PC card are for channels 1 4 bottom to top NOTE 4 fa camera has an associated audio channel connect the camera audio input to the audio channel on the audio adapter cable or 4 channel PC card marked with the same channel number the camera video cable is connected to For instance if the camera video input is attached to the CH 6 connector on the video adapter cable connect the associated audio input to the CH 6 connector of the audio adapter cable Make 1 0 connections If your computer includes an 1 0 connector terminal block make connection to sensors input relays output and an RS485 trunk as needed see the following diagram When selecting the wire color and size for these links follow local codes 10 www sc black com SECTION 3 SYSTEM SETUP Sp elr Output 1 elil Output 2 elil Ground elil Input 1 elil Input 2 el Input 3 el Input 4 el Ground TO trx TO r ONE rx ON rx 1 0 Connector Terminal Assignments Sensor inputs can be configured in the SC Black Digital Surveillance Monitoring System software to trigger recording of one camera or several cameras Sensors and relays can be normally open NO or normally closed NC type devices RS485 terminals TRX RX provide a 4 wire RS485 interface 3 9 Install and setup the monitor If your system includes the Supercircuits LCD17 5 LCD19 5 LDC19W 7 or LCD22W 7 monitor use the following proc
4. Motion Detection Sensitivity 9 With the Name of the camera showing in the IP Camera Settings field click the Assign button H 264 Network IP Camera User Manual 21 Sp SECTION 3 SYSTEM SETUP NOTE Video from the camera will not appear until the Cameras tab is closed and the server is restarted Add other IP devices to the system as needed before restarting 10 Repeat steps 2 through 9 above to add other IP cameras devices to the NVR hDVR 11 Inthe Camera tab click Close 12 When prompted by the server to restart click Yes After the server restarts open the Configure menu and select the channel of the camera s you added to see video from the camera s When the Camera tab is reopened video from the cameras assigned to the system can be viewed in the Current Recording View NOTE window and the Motion Detection Area window by clicking on the camera icon assigned to the camera In an IP only system Live video is not shown on the multi image display 3 10 5 Naming a camera channel The camera channel can be assigned a name that appears on the video image To rename a camera channel 1 Click TOOLS gt Configure to open the configuration Preferences window By default the Camera tab is opened 2 Inthe Select Camera frame click on an analog camera channel you want to name In the example below camera channel 1 is selected 3 Inthe Camera Name frame click the keyboard icon Note that the default name for th
5. address for the Host Server address Email will not be sent out if the email host server is incorrect IT Need Authentication UserID Ea Password Ea E mail Test Se Disk Full Notification ect Events I Send a Relay Output every 5 minutes to fo I Show Warning in every 5 minutes Export Import Export current configuration to file or Import from a file Export Import Export configuration 3 Inthe Export Import frame in lower right corner of the System tab click Export 4 Follow the on screen instructions to identify the location where the export file will be saved NOTE The DIGIOP system configuration file is usually smaller than 50 KB It is named DIGIOPIPDEVICELIST DVR 6 Wait until the message Export successfully completed appears before continuing 3 12 Setup Reflection software Reflection software should be installed on a Windows PC that can connect to the NVR hDVR across a network If the LAN is configured to allow access to the NVR NDVR through the internet the Reflection PC can be anywhere that has high speed internet access Reflection runs on Microsoft Windows XP Professional with SP2 Windows Vista and Windows 7 During the installation process the Reflection installer will also load Microsoft NET Framework 3 5 SP1 24 www sc black com SECTION 3 SYSTEM SETUP Sp For more information about Reflection refer to the Reflectio
6. com SECTION 1 SYSTEM OVERVIEW Sp mn IP Cameras Analog Cameras PoE Switch NVR hDVR IPAdmin Tool Reflection Software J Local System Reflection Software NVR and hDVR Systems Setup Guide 3 Sp SECTION 2 GETTING STARTED UNPACKING YOUR SYSTEM SECTION 2 Getting Started Unpacking Your System For most installations SC Black NVR and hDVR systems come with everything needed to install and operate your surveillance system 2 1 Unpacking the equipment Remove the equipment from its packaging and place it on a flat clean surface Inspect each item If any visible damage is present contact your supplier or Supercircuits for a replacement Verify that your order is complete Within your order you should find The number of cameras you ordered Each IP camera includes a power supply a software CD and a Quick Installation Guide Depending on your camera model other items may be included Monitor with the associated video and power cables and documentation NVR or hDVR with power cables keyboard and mouse remote control software CD and documentation Power over Ethernet PoE switch Accessories you ordered Refer to the user manual for the product for a list of specific items included with the product The user manual may be provided on the CD included with the product NOTE Large systems may be shipped in several cartons 4 www sc black com SECTION 3 SYSTEM SETUP Sp S
7. powering on the camera 4 Wait for the camera to reboot B 3 Checking your Firmware Firmware is software embedded in the camera that determines many of its features and functionality The current firmware version of your camera can be found by viewing video from the camera in IE and then clicking SETUP gt About gt Version To replace or update the firmware in your camera contact the Supercircuits Support Team NVR and hDVR Systems Setup Guide 31 Sp APPENDIX C POWER OVER ETHERNET APPENDIX C Power over Ethernet Some SC Black cameras and encoders support Power over Ethernet PoE in conformance with the IEEE 802 3af standard IEEE 802 3af allows for two power options for Category 5 Cat5 cables C 1 The PoE module signature and control circuit provides the PoE compatibility signature and power classification required by the Power Sourcing Equipment PSE before applying up to 15 W power to the port The high efficiency AC DC converter operates over a wide input voltage range and provides a regulated low ripple and low noise output The AC DC converter also has built in overload and short circuit output protection PoE compatibility With non Power Sourcing Equipment PSE When it is connected with non PSE use the power adaptor to provide power to the camera With power adaptor Connecting both a PSE and a power adaptor does not do any harm to the products Disconnecting the power adaptor while it is operat
8. sources are associated with camera channels by attaching them to the audio connector associated with the camera channel 1 Connect the video adapter cables to the video capture card of the computer The video capture card in some computers accommodate a single 16 channel adapter with BNC and a DVI style connector another type provides an 8 channel adapter with BNC and a VGA style connector Notice that all BNC connectors are labeled for the channel number assigned to the connector Analog Video Input DVI style connector 8 16 channels I O Connections ee n nt de edda Audio Input Channels 4 channel PC card Typical Backpanel for an hDVR NVR and hDVR Systems Setup Guide 9 Sp SECTION 3 SYSTEM SETUP 8 channel video adapter cable 2 Connect the audio adapter cable s to the audio capture card of the monitoring console computer The audio capture card may have 4 inputs numbered 1 4 bottom to top or an audio adapter cable similar to the video adapter cable but includes RCA female connectors instead of a BNC connectors 3 Connect the analog camera video cables to the video adapter cable Note that the each connector is numbered for the assigned camera channel in the SC Black Digital Surveillance Monitoring System software If your computer hardware includes a 4 channel audio PC card and you are installing a camera with audio connect the camera video input to channel 1 2 3
9. the ID and PW the IP Setup window will close Login 192 168 0 100 00 13 23 04 26 18 ID root PW eooo remember ID and password In the IPAdmin Tool window click Refresh and verify that the entry representing the camera now shows the new IP address D 1 Connect to the camera with IE To further test the connectability of the camera network settings and verify video streaming Open Microsoft Internet Explorer IE In the Internet address field enter the newly configured IP address for your camera in the format http lt IP address gt Where lt IP address gt is the IP address of your camera For example if the new IP address of the camera is 192 168 1 201 enter http 192 168 1 201 www sc black com 3 APPENDIX D CONFIGURE THE SC BLACK CAMERA IP ADDRESS Sp If prompted to install an ActiveX control such as AxNVC cab follow screen prompts to install the software amp This website wants to run the Following add on amp xNYC Activex Control Module from Control name is not available If you trust the website and the add on and x want to allow it to run click here IE prompt to install ActiveX control gt Live View BLK 1P5102M Gr Cl dm v page Safety Toos 60 BLACK BLK IPS102M T VIEW SETUP FIRSTSTREAM w UNICAST RTSP v SPK MIC ING VANNS a NSD N R NJ N Ifyou cannot see live vide
10. the entry for your camera and select IP Address PAdminTool V3 7 3 LJE File Setup System ip Setup update Selected Device BLK IPS102M 192 168 0 100 Product Name Rack Info IP Address MAC Address Friendly Name Firmware Uptime Reboot Update IP Address Friendly Name Device info Apply Device count 1 4 Inthe IP Setup window a Select the Static option if it is not selected This option is required to record camera video by a network NVR or hDVR NVR and hDVR Systems Setup Guide 33 Sp APPENDIX D CONFIGURE THE SC BLACK CAMERA IP ADDRESS IP Setup Selected Device BLK IPS102M 192 168 0 100 O DHCP Static Local Network information IP Address 192 168 1 201 Net 1 Subnet Mask 255 255 255 0 Client Network Information Adapter Info OBroadcom Netxtreme 57xx Gigabit Controller Packet Scheduler M peer 192 168 0 1 Adapter Name O E4B3EEF0 20D3 4885 AABD EE6E88979980 DNS D D D D MAC Address 000188b2af940 IP Address 0192 168 1 168 Subnet Mask 0255 255 255 0 Gateway 0192 168 1 1 IP Setup window b Enter the new IP address subnet mask and gateway address into the appropriate fields c Click SETUP A Login window will open d Inthe Login window enter the ID and PW password for your camera and click Login The default administrator values for the ID and PW are root and pass After entering
11. ECTION 3 System Setup Your SC Black NVR ADVR system includes the monitoring console computer with the SC Black Digital Surveillance Monitoring System software a PoE switch and the analog and IP cameras and encoders that you added to it The monitoring console computer PoE switch and IP cameras and encoders are usually configured with fixed static IP addresses on the same subnet Analog cameras are connected directly to the computer through integrated video and audio capture hardware or can be connected across the LAN through an IP encoder Each camera and encoder model has specific installation and usage instructions that should be carefully reviewed when planning the setup of your system Since many systems include the high performance SC Black cameras extra consideration is included herein to aid their installation and setup The general procedure for installing and setting up your system is shown in the following flow chart Check network for compatibility with default IP addresses Section 3 1 Setup the camera configuration Video settings Setup motion detection Etc Section 3 4 Install analog cameras Route power video audio cables to hDVR Sections 3 7 Backup system configuration Section 3 11 Determine the Install IP camera network settings for in its surveillance all IP devices location Connect audio etc Connect network Connect power Section 3 2 Section 3 4 Install
12. ETUP Sp 7 Press the SOURCE button on the monitor control panel to open the video source menu Use the and W buttons on the control panel to highlight PC and then press the MENU button to select that interface An indication will appear on the screen confirming your selection AV BNC SVIDEO PC HDMI 8 Power off the monitor using the Power button on the control panel 3 10 Setup the NVR hDVR system software Make sure the power sources are grounded This helps prevent personal injury or damage to the equipment 1 Before connecting the power ensure that the power source configuration switch on the back of the computer is set to 110 VAC WARNING 2 Make sure all cables are securely attached 1 Power on the NVR hDVR 2 Power on the monitor and wait until the NVR hDVR is initialized When fully initialized the server will display the following SC Black Digital Surveillance Monitoring System multi image screen H 264 Network IP Camera User Manual 13 Sp SECTION 3 SYSTEM SETUP DWR Licanin Ka Configured IF itikat 197 1681 191 BLACK Typical SC Black server multi image display 3 10 1 Login 1 Click LOGIN bottom right of screen 2 Enter a User name and Password in the pop up Input Password window and then click OK The Administrator default User name and Password are admin and admin When the login is successful the LOG IN button label changes to TOOLS Inpu
13. NVR hDVR hardware Install another IP camera Section 3 5 Sections 3 6 Connect analog Install and setup the cameras to the hDVR monitor Connect video and audio cables Section 3 8 Section 3 9 Install Reflection software Connect to the NVR hDVR Section 3 12 General Installation and Setup Flowchart NVR and hDVR Systems Setup Guide Configure the camera network settings Section 3 4 Install analog in their surveillance locations Route power video audio cables to hDVR Sections 3 7 Setup the NVR hDVR system software Configure IP settings Configure cameras Configure sensors Sections 3 10 3 10 5 Sp SECTION 3 SYSTEM SETUP 3 1 Check LAN for default IP address compatibility All IP devices computers cameras encoders etc are initially setup with factory default network settings Some devices are preset with fixed static IP address while others acquire their network settings through a DHCP server Before connecting any IP device with a static IP address to your LAN check the LAN to ensure that it s IP address won t conflict with another device on the LAN For instance all SC Black cameras and encoders are factory configured with the static IP address 192 168 0 100 To avoid network conflicts check the LAN before connecting your camera to ensure that network conflicts won t occur 1 At a Microsoft Windows computer attached to the LAN subnet
14. S BLACK NVR and Hybrid DVR Systems Setup Guide Products BLK SY10 Series Systems BLK SY20 Series Systems Padi es Th P ala TEN EL Tam a PLEASE READ THIS MANUAL BEFORE USING YOUR SYSTEM and always follow the instructions for safety and proper use Save this manual for future reference BLK SY10X 20X_SI 3 11 11 Operate this system only in environments where the temperature and humidity is within the recommended range Operation in temperatures or at humidity levels outside the recommended range may cause electric shock and shorten the CAUTION life of the product Refer to the specifications for each system component for more information LEGAL NOTICE SC Black is a registered trademark of Supercircuits Inc Supercircuits products are designed to meet safety and performance standards with the use of specific Supercircuits authorized accessories Supercircuits disclaims liability associated with the use of non Supercircuits authorized accessories The recording transmission or broadcast of any person s voice without their consent or a court order is strictly prohibited by law Supercircuits makes no representations concerning the legality of certain product applications such as the making transmission or recording of video and or audio signals of others without their knowledge and or consent We encourage you to check and comply with all applicable local state and federal laws and regulations before engaging in any fo
15. Sp SECTION 1 SYSTEM OVERVIEW SECTION 1 Systems Overview SC Black Network Video Recorder NVR and Hybrid Digital Video Recorder hDVR security systems with the Digital Surveillance Monitoring System software feature state of the art management for advanced analog and IP cameras The Digital Surveillance Monitoring System software is used to record and store digital video and images control camera PTZ and improve the video quality brightness contrast chroma U and V hue and gain of analog cameras It also includes several surveillance management features including system security and activity logging All SC Black IP cameras and encoders include an IPAdmin Tool a Microsoft Windows based application for configuring IP camera network settings and firmware updates Depending on your system the IPAdmin Tool may be pre installed on your NVR or hDVR After setting up and configuring your system with the Digital Surveillance Monitoring System software and the IPAdmin tool use Reflection software provided to monitor your system Reflection is a stand alone Microsoft Windows based video dashboard that connects to the NVR hDVR across a local network or from the Internet It provides remote viewing and management of live and recorded video with search playback and download capabilities Reflection accesses your cameras and stored video through your NVR or hDVR It can be used to monitor multiple NVR hDVR systems concurrently 2 www sc black
16. camera or encoder skip this section The IPAdmin Tool included on the CD disk with all SC Black IP cameras and encoders will discover all SC Black IP cameras and encoders attached to your network It is used to perform the initial network setup for each camera and encoder and install firmware updates The IPAdmin Tool can be loaded on a Microsoft Windows XP Vista or Windows 7 operating system To install the IPAdmin Tool do the following 1 Create a directory on your computer hard drive for the IPAdmin Tool application files NVR and hDVR Systems Setup Guide 7 Sp SECTION 3 SYSTEM SETUP 2 Insert the CD disk provided with your camera or encoder into your computer s CD ROM drive and open the CD in a Windows Explorer window 3 Copy the files IPAdminTool exe CgiUtil dII and IPAdminTool dll from the CD to your new directory 3 4 Install and connect the IP camera encoder to the LAN 1 Install the IP camera or encoder in the surveillance location in accordance with the manufactures suggested procedure If your camera will be powered with a PoE switch use this switch in the power LAN connection to verify the functionality of the NOTE switch Refer to Appendix C for more information about PoE powering and your camera 2 Connect your IP camera to the LAN Use the manufacturer s suggested procedure to configure its network settings For SC Black cameras and encoders see Appendix D 3 Adjust the camera video se
17. e analog cameras can CAUTION reside Plan your system configuration carefully 3 Inthe IP Camera Settings frame click Add A Search IP Device window will open 18 www sc black com SECTION 3 SYSTEM SETUP SP Search IP Device I 4 Click OK to Search in Network and open the IP Device List IP Device List ALL IP DEVICES Vivotek 3000 6000 MJPEG Vivotek 3000 6000 MPEG4 FileStreamer MJPEG FileStreamer MPEG2 FileStreamer MPEG4 5 InthelP Device List window select the type of devices attached to the network that you want to add or select ALL DEVICES then click Next The network search will find all devices of the type selected that are supported by the NVR hDVR After the search completes the IP Device window will open and list all devices it found of the type specified H 264 Network IP Camera User Manual 19 SP SECTION 3 SYSTEM SETUP IP Device _IP Device Name IP Address MAC Address fBlack H264 192 168 1 201 00 13 23 04 22 46 O 00 13 23 04 25 E4 Black H264 192 168 1 100 Black H264 192 168 0 101 00 13 23 04 25 23 6 Inthe IP Device window click a device name you want to add to the NVR hDVR In the example above the first item is selected Click Next to open the IP Device Details window IP Device Details Black H264 92 168 1 201 Black H264 http 192 168 1 207
18. e channel is Camera 1 4 Click the character buttons on the keyboard to enter a new name To select an uppercase letter click the Shift button then click the character button The entry will appear in the field at the bottom of the keyboard window 22 www sc black com SECTION 3 SYSTEM SETUP Sp Preference Camera Network Sensar Contral PTZ Color Display FPS Resolution Schedule System Select Camera GJ Cu EG Ak GJ GJ Ck Ok Ck Mk Mk 2k ak Mk Mk GE SS ee ee ee I Scen I Security Screen Mode Watch Mode Camera Name IP Camera Settings me 62 Camera Pen fe Configure Specify the camera location 11326 kbps estimated MB per Hour 802 Motion Detection Sensitivity High Continuous 5 After selecting the new camera name click the Input button in the keyboard window The keyboard window will close 6 To save the entry click Close in the Camera tab 3 11 Export system configuration Although catastrophic failures are extremely rare in the DIGIOP system having the system configuration file backed up enables you to quickly restore the DIGIOP system configuration if that becomes necessary Also the configuration file can be used to pre configure other systems Whenever changes are made to the system configuration export the system configuration to an external storage media To export the system configuration 1 Click TOOLS gt Configure to open the confi
19. edure to setup the monitor Otherwise follow the instructions provided by the manufacturer to setup your monitor and connect it to the computer 1 Find the monitor assembly and base Use the screw provided to attach the base to the monitor support bracket The screw may be attached to the underside of the monitor support bracket or in the base Support Bracket I ge Screw 2 Attach the VGA cable provided with the monitor to the VGA input connector on the lower back side of the monitor Attach the other end of the VGA cable to the VGA connector on the back of the computer NVR and hDVR Systems Setup Guide 11 S SECTION 3 SYSTEM SETUP ED TE HEM I Inputs on the lower back side of monitor 3 Attach an audio cable with RCA mini jacks to the PC Audio connector on the lower back side of the monitor 4 Attach the other end of the audio cable to the audio line out connector on the back of the NVR hDVR The audio line out connector is color coded in light green 5 Attach the power cable to the monitor and plug it into a grounded power outlet 6 Press the Power button to power on the monitor The Power button is located in the control panel on the right side of the monitor SOURCE Move up in menu Move down in menu Move right in menu or volume up Move left in menu or volume down MENU open close lt lt i Power Audio output Monitor control panel 12 www sc black com SECTION 3 SYSTEM S
20. ername This is the username that is to be used to access the NVR hDVR Password This is the password associated with the Username Port Visible for data servers only The TCP IP port number that Reflection will use to connect to the NVR hDVR The default port number used by Reflection is 24752 Timezone Visible for Video Servers only Select the time zone where the NVR hDVR is located Name optional This is the name that identifies the server within Reflection Description optional This is for a description for the system IP Address or Hostname Name optional 192 168 1 191 SC Black server Username Description optional admin Password sv000 Timezone GMT 06 00 Central Time US amp Canada Save Cancel 26 www sc black com SECTION 3 SYSTEM SETUP Sp 5 Click Save Reflection will display the Name of the NVR hDVR you added in the left panel Systems list 6 To open a connection to the NVR hDVR you added double click the Name in the left panel s BLACK so BLACK NVR and hDVR Systems Setup Guide 27 Sp SECTION 4 INSTALLATION TIPS SECTION 4 Installation Tips Camera placement Use the information included in the packaging of your camera to mount and connect the unit to power and video cables Plan your camera installation carefully Identify the locations where cameras will provide the best coverage considering Field of vi
21. ew Cameras must be positioned so they can effectively view the entire area that must be monitored Lighting Is there enough light in the field for the camera to see clearly Is there intense light from the sun or shiny objects that reflect onto the camera lens These conditions may affect the video quality and camera performance Ease of installation Must be able to install the camera at the location considering mounting hardware requirements temperature dust moisture etc Weatherproof cameras Weatherproof cameras can be mounted in any open area such as on a telephone pole or on the side of a building However for best results we recommend you mount your cameras in a sheltered area such as under the eave or roof of a building Point the camera in the direction you wish to observe When routing cable near the camera allow enough slack to form a U shaped drop to help direct moisture that accumulates on the cable away from the camera NOTE Cable connections are not weatherproof Cable runs LAN power cables can be run almost anywhere and are frequently routed above drop acoustic ceilings because of the ease of installation For added security we recommend you run your cables in areas with limited access to prevent tampering Avoid running the cable near high voltage appliances such as fluorescent lighting Electrical noise and magnetic fields produced by these devices may affect video signal quality A 100 Ether
22. guration Preferences window By default the Camera tab is opened 2 Openthe System tab NVR and hDVR Systems Setup Guide 23 Sp SECTION 3 SYSTEM SETUP Preference Camera Network Sensor Contral PTZ Color Display FPS Resolution Schedule System Upgrade Please obtain the Upgrade Software available on Media CD or DYD from your Supplier To proceed after you have the Media press the Select Upgrade button and follow the On Screen instructions Disclaimer If Media is obtained from a Non Qualified Supplier your systems might fail and cannot be recovered If Media is physically damaged contact your Supplier for a replacement Select Upgrade Local C Remote URL Address frie Hocalhost Digi0pESP Jamin IV Don tAsk again for Login at Startup IV Automatically Update IP address ESP Settings User Name Password Select Drive for saving data r Camera License Select Drives Activate More IP Cameras Reset Configuration r System Backup After S W is upgraded or printer driver is installed in Viewer it is recommended to backup system Last Backup Time 2010 01 404 17 54 07 System Backup To reset to factory default configuration Reset to Default T Email Notification DYA Location Send 10 E mail Setting Senders E mail Address Host Server Address BE BE Please enter the SMTP server
23. ickering This is usually a symptom of low voltage at the camera You may have a cable run that is too long a defective cable or an insufficient power supply Try using a better quality cable or plug the power adapter directly into the camera to bypass the cable all together I installed the cables to my analog video equipment but the power plug won t fit into the camera or the power adapter Chances are you ve run the cable backwards Only one end of the camera cables supplied by Supercircuits will fit the camera while only the other end will fit the power adapter The cable will need to be pulled and run the other direction www sc black com APPENDIX B TROUBLESHOOTING APPENDIX B Troubleshooting B 1 Camera reset To reset the camera while it is in use NOTE The BLK IPD101 camera does not have a hardware Reset button 1 Press and hold the Reset button for 3 seconds 2 Wait for the camera to reboot B 2 Set to factory default settings The camera network settings can be forced to the initial factory default settings IP address reset to 192 168 0 100 Subnet mask reset to 255 255 255 0 Gateway reset to 192 168 0 1 User ID reset to root Password reset to pass To force the camera to the factory settings 1 Disconnect the power adapter from the device 2 While pressing and holding down the Reset button connect the power to the camera 3 Release the Reset button 5 seconds after
24. ing does not stop operation The product continues to work without rebooting C 2 Power classification The PoE Power Class supported by the IP device is Class 0 Class Usage Minimum Power Levels Output at the PSE Maximum Power Levels at the Powered Device 0 Default 15 4W 0 44 to 12 95 W 32 www sc black com APPENDIX D CONFIGURE THE SC BLACK CAMERA IP ADDRESS Sp APPENDIX D Configure the SC Black Camera IP Address 1 Open the Windows directory where you installed PAdmin Tool Double click IPAdminTool exe to start the application When the IPAdmin Tool starts it will discover all of the support IP cameras and encoders that exist on the network The discovery process may take several minutes HEG IPAdminTool V3 7 3 File Setup System IP Setup Update Selected Device BLK IPS102M 192 168 38 24 Uptime MAC Address Friendly Name Firmware 00 00 03 Product Name lt Rack Info IP Address 00 13 23 04 26 18 BLK IPS102M 1 02 03 BLK IPS102M 192 168 0 100 Apply Device count 1 IPAdmin Tool discovered 192 168 0 100 NOTE hena camera is powered on it will not respond to network commands until it is fully initialized The initialization process can take up to 2 minutes 2 Inthe Product list find the entry with the same MAC address as the camera you are configuring If the camera is not shown click Refresh repeatedly to update the list 3 Right click on
25. n Software User Manual or the Reflection Software Quick Start Guide 3 12 1 Install Reflection Reflection is provided on the Application disk included with your NVR or hDVR hardware 1 Insert the Application disk into a DVD drive on your computer and find the ReflectionInstaller exe file Double click or Run this file to start the installation 2 Follow the screen prompts to install Reflection on your computer After you click Finish the SC icon see below will appear on the desktop and in your Windows Start Menu 3 12 2 Connect Reflection to the NVR hDVR 1 Start Reflection by double clicking the desktop icon or using the Windows Start menu Weicome to Reflection local English United States s Login 2 Click Login at the bottom of the dialog box to open Reflection 3 In the Reflection main window click Configuration gt Add gt Digiop Video Server in the upper left corner of the window NVR and hDVR Systems Setup Guide 25 S SECTION 3 SYSTEM SETUP se BLACK BLACK c BLACK q IF Address or Hostname Mare opbkonalj semane Description optional Localiser Pasw Tits GMT 06 00 Central Time US amp Canada Faye Cancel 3 07 FH 4 Enter the DVR configuration fields with the information necessary to identity your NVR or hDVA It should include IP Address or Hostname This is the IP address or the host name of the NVR hDVR Us
26. nceanecrewaderaberadimadadeed eid Wie eebeewavtewseen 8 3 7 Install analog cameras hDVR systems only cceeccceeeecccesecceennseceeues 8 3 8 Connect analog cameras to the hDVR hDVR systems only n nunne 9 39 Installand setup the MIONION RR 11 3 10 Setup the NVR hDVR system software ccsscceecssesscesessesssercesenenseres 13 VIN 14 3 10 2 Configure NVR hDVR network settingS 0cccececeeeeeeeeseeeeeeeeeees 15 3 10 3 Configuring analog cameras hDVR systems only ceee eee eeeeee eee eeeeas 16 3 10 4 Add IP cameras to the system lt 0 dcerscncesetonaersennaencenoneeeressenceweseetes 18 3 10 5 Naming a camera AIM suser vines 2saGuoresinketeveakteediesthusaenwedenreass 22 3 11 Exportsystem CONNGUTANION EE dentine 23 3 12 Setup Reflection SONWANC Lise e ATEREA 24 PN 25 3 12 2 Connect Reflection to the NVR hDVR ccc cee ccceeeeeeeeeeeeeeeeeeaes 25 TJ EE GI c cvits ctecxeeesee esses vsekecehengdendaecddongeasetenteunseeksernesae s 28 RE ancien chew EE EEE EE RET 30 Ke ES REE 31 NNN 31 EEE GSE EDR 31 B3 Checking GTA EET EET ERE 31 Power over NSR 32 A e e E E E E T E aes 32 C2 Power cassiCauom EE EE NE EE EE 32 Configure the SC Black Camera IP Address avevwanenannanenennenennnnnnenennenenee 33 D 1 gt COMMER 10 the camera with PES NER 34 PE ccacnrntecccaneeusaeanesnyssunecuse cs ooathestneaenecensaorcesesueceuesex 36 NVR and hDVR Systems Setup Guide 1
27. net cable is shipped with every camera in your system Custom cut cables are also available from Supercircuits NVR hDVR placement Your monitoring and recording equipment is central to the accurate capture of video evidence and constant surveillance Supercircuits strongly suggests that it be installed in a secure location with access limited to authorized personnel Additionally NVRs and hDVRs generate heat and should be placed in a well ventilated area Excessive heat will reduce the life span and reliability of the equipment 28 www sc black com SECTION 4 INSTALLATION TIPS Sp The monitor does NOT need to be on for recording to take place NVRs and hDVRs will output and record video regardless of the operational status of the monitor Uninterruptible power supplies It is strongly suggested that power to the system be routed through an uninterruptible power supply UPS These devices will keep your security system running through most power outages in addition to providing excellent voltage surge and drop protection The UPS should support your video recorder and all cameras to ensure operation during power outages NVR and hDVR Systems Setup Guide 29 Sp APPENDIX A FAQ APPENDIX A FAQ Q cannot see video from my camera at the DVR NVR or hDVR What can I do to restore the video First test the connection to the device using the IPAdmin Tool Can you see all the cameras on your network with this utility
28. o after logging into your camera and the following message appears NOTE Cannot Create XMLDOMDocument Install MSXML4 0 download and install the MS XML 4 0 library The library can be found at http www microsoft com downloads details aspx familyid 3 144B72B B4F2 46DA B4B6 5D 485F2B42 amp displaylang en After loading ActiveX controls and updating your XML library a video stream from the camera should appear NVR and hDVR Systems Setup Guide 35 S APPENDIX E DEVICE LOG APPENDIX E Device Log The following table is provided as an aid to setting up and logging the IP devices on your network IP Device Summary Location Gateway Subnet Mask IP Address MAC address Description SKU NVR hDVR 36 www sc black com APPENDIX E DEVICE LOG Sp Analog Camera Device Summary hDVR Camera Model Audio Y N Location Channel 1 2 NVR and hDVR Systems Setup Guide 37
29. rded Video Quality Low 100 High Low 2 High Peman OF Low 80 High Continuous LE TT Sl Te aT ete UD D Siete Cette 5 ETO E E E eee j AN Click the Enable Audio checkbox to select it Click the Close button at the bottom of the window Ifin Step 1 you selected Pause Recording the hDVR was in recording click TOOLS gt Start Recording Otherwise skip this step H 264 Network IP Camera User Manual 17 Sp SECTION 3 SYSTEM SETUP 7 Repeat this procedure for each analog camera channel for which you want to enable audio 3 10 4 Add IP cameras to the system To add IP cameras for NVR ADVR monitoring do the following 1 Click TOOLS gt Configure to open the configuration Preferences window By default the Camera tab is opened Camera Network Sensor Contral PTZ Color Display FPS Resolution Schedule System Select Camera TE Ck GEK Gu Gp Gu Gu Eu Gu Gu OL Ek Gu Cy Gu GEN CZK Ek Ek Oe EIk k aw an aw Ha 274 aw Coe GOW GI Ek Sci l Security Screen Mode Watch Mode Camera Name IP Camera Settings fanalogCamera its Add Edit Delete Assign SPR STEN it ae ol Pete eeeeeee teeta e eee 2 Inthe Select Camera frame click on an unused camera channel red icon When the channel is selected the icon is gray In the example above camera channel 1 is selected To avoid potential configuration errors in hDVR systems do not assign IP cameras to channels wer
30. rm of surveillance or any transmission of radio frequencies Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products Supercircuits Inc disclaims any proprietary interest in trademarks and trade names other than its own No part of this document may be reproduced or distributed in any form or by any means without the express written permission of Supercircuits Inc 2010 2011 Supercircuits Inc All rights reserved 11000 N Mopac Expressway Building 300 Austin TX 78759 Sales Support 1 800 335 9777 Fax 1 866 267 9777 ii www sc black com Table of Contents 69 SECTION 1 SECTION 2 SECTION 3 SECTION 4 APPENDIX A APPENDIX B APPENDIX C APPENDIX D APPENDIX E SEE ETTE EE EE eer as 2 Getting Started Unpacking Your System ovwvwanenennanennnnenennnnenenenneneneen 4 2 1 Unpacking the equipment ua seere a 4 SYSTEM SCLUD REE EE T T E E T 5 3 1 Check LAN for default IP address compatibility 0 ccc eee cece cence ee ee neeeeeeees 6 3 2 Determine the network settings for each IP deViCe 6 eee eee c cece cette cece ee eee eeees 7 3 3 Install the IPAdmin Tool for SC Black IP cameras cece eccee cece eeeeeeeeeeeeeees 7 3 4 Install and connect the IP camera encoder to the LAN cece ec cee eee e eee e ee eeees 8 5 Repeatior al IP Lame eener EEEREN 8 3 6 Install the NVR or hDVR hardware s ci
31. ss before connecting it to the surveillance LAN Determine the new IP adaress for the device using the procedure outlined in section 3 2 below Setup the device temporarily on a LAN where 192 168 0 100 is not in use and power it on NOTE Install the IPAdmin Tool on a computer on the LAN where the device is temporarily located see Section 3 3 Use the IPAdmin Tool to setup the new IP address subnet mask and gateway for the device see Section 3 5 below Power off the device and disconnect it from the LAN where it was temporarily setup It will retain the new network settings you configured it with 3 Use the ping command to verify that the static IP addresses of other devices in your surveillance system won t conflict with devices already installed on the LAN 3 2 Determine the network settings for each IP device Consult with your LAN network administrator to obtain a list of network settings for each IP device including the NVR or hDVR and all cameras and encoders you will attach to your LAN You must use a static IP address for your surveillance system to ensure connectability with the NVR or hDVR The table included in Appendix E may be useful for logging your network settings To determine or verify which IP addresses are available on your surveillance network use the ping command as described in section 3 1 to test each address 3 3 Install the IPAdmin Tool for SC Black IP cameras if you are NOT installing an SC Black IP
32. t password x OK amp Enter user name and password that is OK valid for this program Cancel Input password 14 www sc black com SECTION 3 SYSTEM SETUP SP 3 10 2 Configure NVR hDVR network settings 1 Click TOOLS gt Configure gt Network to open Network tab Preference 2 If not already check marked click the Enable Network option in the upper left corner to select it 3 Inthe Enable Network frame click the Edit button to open the Network Settings window H 264 Network IP Camera User Manual 15 Sp SECTION 3 SYSTEM SETUP Network Connection Settings x Network Adapter Adapter List GET eee Grader etee dale Y IP Address Obtain an IP address automatically Specify an IP address IP Address 192 168 1191 Ss Subnet Mask 255 255 255 0 Gateway Gateway Address f 92 168 1 1 DNS Obtain DNS automatically Specify DNS address Host BFKZRK1 Ss Domain E DNS server address ag cos 4 Inthe Network Connection Settings window select the network options you prefer then click OK NOTE oaccess the Internet from the system you must define a DNS server Contact your system administrator for more information 5 Attach the Ethernet LAN cable to your NVR HDVR 3 10 3 Configuring analog cameras hDVR systems only Analog cameras are automatically added to the hDVR system The video image from
33. the camera will appear on the camera channel associated with the video connector it is physically attached to If the camera has an associated audio channel it must be enabled in the SC Black Digital Surveillance Monitoring System software Use the following procedure to enable audio Enable analog camera audio channel 1 Click TOOLS gt Pause Recording if it appears in the menu then click OK in the Warning window Pause Recording only appears in the menu if the hDVR is recording 16 www sc black com SECTION 3 SYSTEM SETUP Sp x A Pause Recording Warning For added security the system resumes recording if paused for more than 5 minutes Do you want to pause recording now i Cancel Click TOOLS gt Configure gt Cameras to open the Camera tab Click the camera icon for the camera channel for which you want to enable audio In the example shown below camera channel 1 was selected Camera Channel Icon Enable Audio Option Camera Network Sensor Contral PTZ Color Display FPS Resolution Schedule System m Select Cera Cok 2h h GEN Eh GER CDD E GE k k Bk Cop Cu 226 Bk 24H SW Gow 27 286 29 GOW Eik 320 I Scene Loss EE I Security Screen Mode I Watch Mode Camera Name IP Camera Settings ee Ea F Current Recording View Motion Detection Area Vv Cover Entire Area 6 BLACK m Scene Loss Sensitivity Ge Detection Sen gt Reco
34. ttings setup the motion detection configuration etc if necessary 4 Verify connectability to the device using network based software as suggested by the manufacturer For SC Black cameras and encoders see Appendix D 3 5 Repeat for all IP cameras Repeat step 3 4 for each camera or encoder you install Setup one camera at a time to prevent network conflicts between cameras that have the same initial IP address 3 6 Install the NVR or hDVR hardware Install your NVR or hDVR hardware Refer to the Quick Start Guide included with the equipment Do not power on the NVR hDVR at this time 3 7 Install analog cameras hDVR systems only If you are installing an hDVR system with analog cameras do the following 1 Install and setup all analog cameras in their surveillance locations in accordance with the manufactures suggested procedures 2 Route the video audio power extension cable from each camera to the location where the hDVR is installed 8 www sc black com SECTION 3 SYSTEM SETUP Sp NOTE Typically the power connectors on video extension cables are different at each end When routing these cables ensure that the connectors match the devices they attach to 3 8 Connect analog cameras to the hDVR hDVR systems only Analog cameras are assigned to camera channels in the SC Black Digital Surveillance Monitoring System software by attaching them to the video connector associated with the channel Similarly audio
35. where the camera will be connected surveillance network open a Command Prompt window a Click the Windows Start button and select Run b In the Open field enter cmd then click OK Run z x z Type the name of a program Folder document or Internet resource and Windows will open it for you Open cmd vi At the command prompt use the ping command to see if the default IP address of your IP device is in use If the default static IP address is 192 168 0 100 enter ping 192 168 0 100 C WINDOWS system32 cmd exe 5 x N gt ping 192 168 6 166 inging 192 168 686 166 with 32 bytes of data equest timed out equest timed out equest timed out equest timed out ing statistics for 192 168 606 166 Packets Sent 4 Received Lost 4 186 loss gt The Request timed out response indicates that the IP address is not currently in use and the camera can probably be connected without causing conflicts www sc black com SECTION 3 SYSTEM SETUP Sp A Reply from message received from a ping indicates that an active device with that IP address exists on the network and new devices with that address shouldn t be attached to that network without first changing the network settings of the device Use the manufacturer s recommended procedure for changing the address before attaching it to the LAN For SC Black cameras and encoders To change the IP addre
Download Pdf Manuals
Related Search