Owner`s Manual (General)
Contents
1. 0 c0ceeeeeeeee 7 One Year Limited Warranty 0005 8 How to Obtain Warranty Service 8 _ Welcome Congratulations on your purchase of a SUNBEAM Blender Sunbeam has designed your blender to provide the utmost in quality ease of use and convenience Sunbeam offers you an blender to fit your lifestyle Date product received Service number Located on the bottom of the blender _ Learning About Your 10 SPEED BLENDER 1 Filler Cap also used to tighten or loosen blade assembly 2 Lid 3 Jar 48 ounce 4 Gasket 5 Blade Assembly also called cutting blades 6 Base 7 Control Panel 8 Off Pulse Button Your Blender 7 gt FF o gt o G G3 er After unpacking the blender wash everything except the blender base in warm soapy water Dry thoroughly Do not place in a Wipe the blender base with a damp cloth or sponge Do not immerse the base in water Care should be taken when handling the blades as they are very sharp How to Assemble and Use Important Your blender jar and cutting blades are subject to wear during normal use Always inspect cutting blades for broken cracked or loose blades If jar or cutting blades are damaged do not use Call our toll free customer service number to obtain replacement parts e Make sure blender is unplugged Place blender base on clean dry surface to keep foreign particles from being pulled up2. use contrary to the operating instructions disassembly repair or alteration by anyone other than Sunbeam or an Authorized Sunbeam Service Center Further the warranty does not cover Acts of God or nature such as fire flood hurricanes and tornadoes Sunbeam shall not be liable for any incidental or consequential damages caused by the breach of any express or implied warranty Except to the extent prohibited by applicable law any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty Some states provinces or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above exclusion or limitations may not apply to you This warranty gives you specific legal rights and you may have the rights that vary by state province and or jurisdiction How to Obtain Warranty Service Take the product to an Authorized Sunbeam Service Center You can find the nearest Authorized Sunbeam Service Center by calling 1 800 458 8407 or visit our Website at www sunbeam com DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE
3. into motor during operation e Make sure gasket is in place on outer rim of blade assembly The gasket must lie flat Screw the blade assembly counterclockwise into the jar base firmly using the finger tabs on the bottom of blade assembly e To easily assemble into the jar tilt the blade assembly slightly and enter with the serrated blade that curves up Move as needed to clear the remaining blades When seated properly turn the blade assembly counterclockwise to tighten To remove just reverse the process turn the blade assembly clockwise and lower slightly and in the direction of the serrated blade tilt up and the other blades will clear the jar bottom opening FIGURE 1 e NOTE The blade assembly will turn counter clockwise to tighten and clockwise to loosen The transparent filler cap is designed to assist in tightening and loosening the blade assembly if necessary FIGURE 2 e Remove the filler cap from its position in the jar lid and note the notches in the bottom open end These notches or slots engage the ribs on the FIGURE 2 underside of the blade assembly on either side of the rubber coated drive shaft Ficure 3 Hold filler cap firmly in hand and engage the ribs into the slots Remember to turn counter clockwise to tighten and clockwise to loosen the blade assembly in the jar Ficure 4 It is easier if you assemble the blade assembly into the jar with your fingers first and then use
4. the filler cap to tighten Set jar into place on blender base making sure it is securely seated by twisting jar clockwise until it snaps into the locked position You may not hear an audible snapping sound but will feel it lock into place Plug cord into outlet Put ingredients in jar place lid with filler cap in place on jar making sure it is pushed down completely into position Process food or beverages Place hand on lid when blending liquids Push desired button on control panel to start blender Always turn blender OFF and wait until blades have stopped rotating before removing jar or lid To remove jar after blending is complete hold blender base with one hand and grasp jar handle with the other hand and twist jar counterclockwise approximately a quarter turn to unlock then lift jar straight up from base Never place jar onto unit while motor is running Never run empty Never run without jar FIGURE 3 Using the 10 Speed Your blender has 5 speed buttons with separate high and low range buttons giving a total of 10 speed functions When low button is pressed the speeds are Stir Puree Chop Whip and Mix When High button is pressed the speeds are Grate Blend Grind Liquefy and Ice Crush In addition there is a Pulse Off button that is a controlled cycle operation This means it operates only while the button is held down All other spee
5. Sunbeam 10 SPEED BLENDER Model 4182 4183 4184 Manual IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed including the following READ ALL INSTRUCTIONS KEEP THESE INSTRUCTIONS FOR FUTURE USE Verify that the voltage in your home corresponds to that of your appliance To protect against risk of electrical shock do not put cord plug base or motor in water or other liquid Close supervision is necessary when any appliance is used by or near children Unplug cord from outlet when not in use before putting on or taking off parts and before cleaning Avoid contact with moving parts Do not operate any electrical appliance with a damaged cord or plug or after the appliance malfunctions or has been dropped or damaged in any manner Return appliance to nearest Sunbeam Appliance Authorized Service Center for examination electrical repair mechanical repair or adjustment The use of attachments including canning jars not recommended by the manufacturer may cause a risk of injury to persons Do not use outdoors Do not let cord hang over the edge of a table or counter or touch hot surfaces including the stove Keep hands and utensils out of container while blending to reduce the risk of severe personal injury and or damage to blender A rubber spatula may be used but must be used only when blender is not running Do not use a broken chipped or cra
6. cked blender jar Do not use broken cracked or loose cutting blades To reduce the risk of injury never place cutting unit blades on base without jar properly attached Blades are sharp handle with care Always operate blender with cover in place When blending hot liquids remove center piece of two piece cover Do not fill blender container beyond 3 cup level Always begin processing at the lowest speed setting Keep hands and other exposed skin away from the cover opening to prevent possible burns Jar will become hot from hot contents Screw on blade assembly firmly Injury can result if moving blades accidentally become exposed If the jar should turn when the motor is switched ON switch OFF immediately and tighten blade assembly Do not leave blender unattended while it is operating To disconnect cord turn the control to OFF then remove the plug from wall outlet Do not use appliance for other than intended purpose SPECIAL INSTRUCTIONS THIS APPLIANCE INTENDED FOR HOUSEHOLD USE ONLY Use for food or liquids only This appliance is equipped with a polarized plug This type of plug has one blade is wider than the other This plug will fit in a polarized outlet only one way This is a safety feature intended to help reduce the risk of electrical shock If you are unable to insert the plug into the outlet reverse the plug If it the plug should still fail to fit contact a qualified electrician to rep
7. ds are continuous cycle operation They operate continuously at whatever speed is selected until the Off button is pressed Pulse speed is same as Ice Crush which is maximmum speed For Continuous Operation Determine whether you want to use the High or Low range continuous cycle operation and press the button Rest one hand on top of blender jar with lid securely in place Press desired speed button to turn blender on Press Off button to turn blender off For Controlled Cycle Operation Rest one hand on top of blender jar with lid securely in place Press Pulse button and hold down for about 2 seconds Release Pulse button and allow blades to coast to a stop Repeat cycles until contents reach desired consistency Release of the Pulse button turns blender off Note Pulse button can be held longer than 2 seconds as needed Pulse Button For instant control the pulse function operates only as long as the button is held down The blender motor stops when the button is released Sento High Grate Blend UN Hints for Best Use e Processing hot foods or liquids in the blender may cause hot liquid to spurt out when the cover is removed Always remove the filler cap from the cover before blending hot foods or liquids Jar will become hot from hot contents Please review Important Safeguards section e To add foods when blender is operatin
8. g remove filler cap from container cover and add ingredients through the opening e If blending action stops during blending or ingredients stick to the sides of the jar turn blender OFF Remove the cover and use a rubber spatula to push mixture towards blades e If using your blender to make salsa or other recipes using tomatoes onions and other vegetables you may have better results using a slower speed function or the pulse function e Do not try to mash potatoes mix stiff dough whip egg whites grind corn raw meat or extract juices from fruits and vegetables The blender is not made to perform these tasks e Do not store food or liquids in the blender jar e Avoid bumping or dropping the blender ___Maintaining Your 10 SPEED BLENDER How to Clean the Blender Unplug the blender from electrical outlet Wipe blender base control panel and cord with a damp cloth or sponge To remove stubborn spots use a mild non abrasive cleanser To clean jar unscrew blade assembly and tilt slightly to remove from jar Use filler cap to assist if necessary Carefully remove gasket from outer rim of blade assembly Carefully wash blade assembly gasket jar and cover in warm soapy water Rinse and dry thoroughly Do not soak Do not wash blade assembly gasket plastic jar or cover in a dishwasher Replace gasket on blade assembly screw into jar and replace onto blender base Customer Service If y
9. lace the obsolete outlet Do not attempt to defeat this safety purpose of the polarized plug by modifying the plug in any way The length of the cord used on this appliance was selected to reduce the hazards of becoming tangled in or tripping over a long cord If a longer cord is necessary an approved extension cord may be used The electrical rating of the extension cord must be equal to or greater than the electrical rating of the blender 3 4 ampere Care must be taken to arrange the extension cord so that it will not drape over the countertop or tabletop where it can be pulled on by children or accidentally tripped over If the blender blades lock and do not move it will damage the motor Do not use Call the toll free customer service number for information Do not place blender in the freezer filled with food or liquid This will freeze and damage the blade assembly jar and motor SAVE THESE INSTRUCTIONS Table of Contents Welcome icc tanran oie ate hed wont wet 1 Learning About 10 Speed Blender 2 How to Assemble and Use 3 Using the Blenders Special Features 5 10 Speeds si cisaeanedeea nee 5 For Continuous Operation 0 5 For Controlled Cycle Operation 5 Pulse Button 4 2 44 282444448 teed es eras 5 Hints for Best Use 0 cece eee eens 6 Maintaining Your 10 Speed Blender 7 Customer Service
10. ou have a question about your blender call our toll free customer service number 1 800 458 8407 Before calling please note the model type and series numbers and fill in that information below These numbers can be found on the bottom of your blender This information will help us answer your question much more quickly One Year Limited Warranty Sunbeam Products Inc Sunbeam warrants that for a period of one year from the date of purchase this product will be free from defects in material and workmanship Sunbeam at its option will repair or replace this product or any component of the product found to be defective during this warranty period Replacement will be made with a new or remanufactured product or component If the product is no longer available replacement may be made with a similar product of equal or greater value This is your exclusive warranty The warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable Keep the original sales receipt Proof of purchase is required to obtain warranty performance Sunbeam dealers service centers or retail stores selling Sunbeam products do not have the right to alter modify or any way change the terms and conditions of this warranty This warranty does not cover normal wear of parts or damage resulting from any of the following negligent use or misuse of the product use on improper voltage or current
Download Pdf Manuals
Related Search