INSTALLATION INSTRUCTIONS G A S BBQ G RILLS
Contents
1. as well as all state municipal and local codes The correct voltage frequency and amperage must be supplied to the appliance from a dedicated grounded circuit which is protected by a properly sized circuit breaker or time delay fuse The proper voltage frequency and amperage ratings are listed on the product rating plate Record the model and serial numbers before installing the gas BBO grill Both numbers are listed on the product rating plate located on the rear panel of the grill Model Number Serial Number A WARNING If the information in this book is not followed exactly a fire or explosion may result causing property damage personal injury or death Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance An LP gas cylinder not connected for use shall NOT be stored in the vicinity of this or any other appliance IMPORTANT NOTE Installation and service must be performed by a qualified installer service agency or the gas supplier a Warranty service must be performed by a Wolf authorized service center WHAT TO DO IF YOU SMELL GAS Shut off gas to the appliance s Extinguish any open flame Open the lid or hood f the odor continues immediately call your gas supplier or fire department CONTACT INFORMATION Wolf Customer Service 800 332 9513 Website wolfappliance com WOLF GAS BBQ GRILLS PORTABLE LOCATIO2. 4 705 Opening Depth 263 4 680 Dimensions may vary to 1 s 3 Dimensions may vary to 1 s 3 INSTALLATION SPECIFICATIONS NON COMBUSTIBLE ENCLOSURE Built In Models 481 4 1226 263 4 680 gt 3 ROUGH OPENING WIDTH ROUGH OPENING 76 DEPTH i A 91 2 242 21 8 91 2 242 LOCATE ROUGH aih 54 ROUGH ELECTRICAL OPENING HEIGHT 22 a OPENING HEIGHT OUTLET FOR 70 ROTISSERIE lt 17 8 48 48 2 51 DIAMETER OPENING FOR GAS SUPPLY CONNECTION BOTTOM LOCATION ON LEFT SIDE rea ALLOW OPENING 361 2 max FOR ACCESS 2 51 DIAMETER OPENING 927 DOOR FOR GAS SUPPLY CONNECTION BACK WALL LOCATION OR BOTTOM LOCATION NON COMBUSTIBLE ENCLOSURE Dimensions in parentheses are in millimeters unless otherwise specified 9 IMPORTANT NOTE You must follow all National Electrical Code regulations In addition be aware of local codes and ordinances when installing your service 10 WOLF GAS BBQ GRILLS ELECTRICAL REQUIREMENTS IMPORTANT NOTE This appliance must be properly grounded to avoid shock hazard In applications where there is a rear wall behind the BBQ grill locate the electrical service on the left hand side for the rotisserie motor The rotisserie motor requires a 110 120 V AC supply The 6 1 8 m power supply cord on the motor is eguipped with a 3 prong grounding plug To minimiz
3. MODELS Model BBQ36BI shown 30 762 OVERALL DEPTH 303 8 771 WITH HOOD OPEN n BUILT IN MODELS Overall Width 36 914 Overall Height 26 660 Height to Grilling Surface 91 2 241 Overall Depth 30 762 Dimensions may vary to 7 8 3 CART MODELS Overall Width Overall Height 293 4 26 756 660 HEIGHT gt OVERALL WITH HEIGHT Y __ HOOD iis ies ale ime 91 2 241 OPEN TO GRILLING 9 9 SURFACE 36 914 lt 255 8 651 OVERALL WIDTH 36 914 523 4 1340 Height to Grilling Surface 361 4 921 Overall Depth 30 762 Dimensions may vary to 1 a 3 OVERALL DIMENSIONS CART MODELS Model BBO36C shown 30 762 gt OVERALL DEPTH 303 8 771 WITH HOOD OPEN n tt N A D 561 2 ay 26 1435 11 660 lt gt HEIGHT HEIGHT WITH OF GRILL ne mie mie e e 523 a HOOD m l A A A A 1340 OPEN 0 6 6 6 6 2 q 1 1 HEIGHT d 361 4 921 TO GRILLING SURFACE 263 4 680 HEIGHT OF CART 6 9 Y amp 36 914 lt 255 8 sy OVERALL WIDTH INSTALLATION INSTRUCTIONS 48 1219 GAS BBQ GRILLS OVERALL DIMENSIONS BU
4. in an upright position and the hose is not kinked The grill has been tested and is free of gas leaks The homeowner has been informed of the gas supply shut off valve location TROUBLESHOOTING IMPORTANT NOTE If the gas BBO grill does not operate properly follow these troubleshooting steps u Verify that gas is being supplied to the BBO grill a Check the gas supply and electrical connections to ensure that the installation has been completed correctly Check that gas valves are turned to the ON position Follow troubleshooting procedures as described in the Wolf Gas BBO Grills Use amp Care Information Ifthe BBO grill still does not work contact a Wolf authorized service center Do not attempt to repair the grill yourself Wolf is not responsible for service required to correct a faulty installation A WARNING Be sure to disconnect the electrical and gas supply before servicing Surface burners can be lit manually with a match Use extreme caution INSTALLATION INSTRUCTIONS IF YOU NEED SERVICE m f service is necessary maintain the quality built into your gas BBO grill by calling a Wolf authorized service center To obtain the name and number of a Wolf authorized service center check the Locator section of our website wolfappliance com or call Wolf Customer Service at 800 332 9513 CONTACT INFORMATION When calling for service you will need the Wolf Custonter a Service g
5. in the area while doing a leak test Conduct leak tests outdoors in a well venti lated area Do not use a flame such as a lighted match to test for leaks Use only a soap and water solution for leak testing such as half liquid soap and half water Have a dealer check the cylinder for deteriora tion when the tank is filled in accordance with regulations Immediately replace cylinder if any deterioration is found A WARNING Testing for gas leakage of the appliance shall be conducted according to the manufacturer s instructions Dimensions in parentheses are in millimeters unless otherwise specified LEAK TESTING PROCEDURE Check that all the control knobs are in the OFF position Mix a solution of half liquid soap and half water Turn the cylinder valve knob counterclock wise one turn to open Apply the soap and water solution on joints of the gas delivery system Bubbles in the soap and water solution indicates that a leak is present Stop a leak by tightening the loose joint or by replacing the faulty part with a replace ment part recommended by the manufac turer Do not attempt to repair the cylinder valve if it should become damaged The cylinder must be replaced If you are unable to stop a leak shut off the gas supply at the cylinder valve Remove the cylinder from the grill Call a Wolf authorized service center Do not use the appliance until the leak is corrected Push in and turn any contr
6. GAS BBQ GRILLS NSTALLATION NSTRUCTIONS WOLF s S 6 WOLF WOLF is a registered trademark of Wolf Appliance Company LLC As you follow these instructions you will notice WARNING and CAUTION symbols This blocked information is important for the safe and efficient installation of Wolf equip ment There are two types of potential hazards that may occur during installation A CAUTION signals a situation where minor injury or product damage may occur if you do not follow instructions A WARNING states a hazard that may cause serious injury or death if precautions are not followed Another footnote we would like to identify is IMPORTANT NOTE This highlights informa tion that is especially relevant to a problem free installation WOLF GAS BBQ GRILLS INSTALLATION REQUIREMENTS IMPORTANT NOTE This installation must be completed by a qualified installer service agency or gas supplier IMPORTANT NOTE Save these Installation Instructions for the local inspector s use Please read the entire Installation Instruc tions prior to installation Installer please retain these instructions for local inspector s reference then leave them with the homeowner Homeowner please read and keep these instructions for future reference and be sure to read the entire Use amp Care Information prior to use IMPORTANT NOTE This appliance must be installed in accordance with National Electrical Codes
7. ILT IN MODELS Model 62 1 shown 30 762 gt OVERALL DEPTH _ 36 914 gt gt 303 8 771 WITH HOOD OPEN lt 26 660 OVERALL HEIGHT ime re re re re nun 91 2 241 9 9 6 6 TOGRLLING df 48 1219 255 8 651 OVERALL VVIDTH BUILT IN MODELS CART MODELS Overall VVidth 48 1219 Overall VVidth 48 1219 Overall Height 26 660 Overall Height 523 4 1340 Height to Grilling Surface 91 2 241 Height to Grilling Surface 3617 4 921 Overall Depth 30 762 Overall Depth 30 762 Dimensions may vary to 1 8 3 Dimensions may vary to 1 8 3 OVERALL DIMENSIONS CART MODELS Model BBO362C shown 30 762 OVERALL DEPTH 36 914 309 8 771 WITH HOOD OPEN F n d 561 2 26 1435 660 HEIGHT HEIGHT WITH OF GRILL ne ne it it 523 4 HOOD SH 5 IN EN ER Az A PEN 66666 gm i i HEIGHT 361 4 921 TO GRILLING hs SURFACE 263 4 680 HEIGHT OF CART 48 1219 255 8 651 OVERALL VVIDTH Dimensions in parentheses are in millimeters unless othervvise specified WOLF GAS BBQ GRIL
8. LS 36 914 GAS BBQ GRILLS INSTALLATION SPECIFICATIONS COMBUSTIBLE ENCLOSURE Built In Models ALLOW OPENING FOR ACCESS DOOR BOTTOM LOCATION COMBUSTIBLE ENCLOSURE NOTE Dimensions include insulated liner COMBUSTIBLE ENCLOSURE Opening Width Opening Height Opening Depth Dimensions may vary to 1 s 3 38 1 4 972 101 2 267 27 3 4 705 18 gt 457 min lt 38 1 4 972 gt lt 18 gt 273 4 705 18 ROUGH OPENING WIDTH 457 min ROUGH OPENING 457 min E DEPTH A LOCATE 1 31 rr 79 ELECTRICAL OPENING OPENING OUTLET FOR HEIGHT 33 4 95 HEIGHT ROTISSERIE ON LEFT SIDE 31 8 1 gt lt 27 8 g 361 2 max 927 2 51 DIAMETER OPENING FOR GAS SUPPLY CONNECTION BACK VVALL LOCATION OR 2 51 DIAMETER OPENING FOR GAS SUPPLY CONNECTION BOTTOM LOCATION NON COMBUSTIBLE ENCLOSURE Opening Width 361 4 921 Opening Height 91 2 242 Opening Depth 263 4 680 Dimensions may vary to 1 8 3 INSTALLATION SPECIFICATIONS NON COMBUSTIBLE ENCLOSURE Built In Models ALLOW OPENING FOR ACCESS DOOR e 6 152 6 gt min 361 4 921 gt 152 lt ROUGH OPENING WIDTH min 91 2 242 21 8 LOCATE ROUGH 23 a 54 ELECTRICAL OPENING HEIGHT OUTLETFOR C o O R
9. NS LOCATION CONSIDERATIONS Consider the following when choosing a site for using your Wolf BBO grill a Always maintain a minimum clearance of 24 610 from all four sides of the grill to any combustible surface The grill should be level and not be exposed to the wind during use s Never locate the grill in an enclosed area such as a garage shed breezeway or under overhead combustible construction Keep clear of trees and shrubs a Allow adequate area for smoke to dissipate Allow for an adequate supply of fresh air for proper combustion and ventilation a Lock the wheel casters when you have positioned the grill in a safe location Keep fuel hoses and power supply cords away from hot surfaces This outdoor BBO grill is not intended to be installed in or on recreational vehicles or boats Use only extension cords that are specified for outdoor use BUILT IN LOCATIONS Your Wolf BBO grill is designed for easy placement into a built in enclosure For a combustible enclosure use the optional insu lated liner and build your opening according to the Installation Specifications illustration for your specific model on pages 8 9 For non combustible masonry or other enclosure also follow the specifications on pages 8 9 Maintain specified clearances Both installations require a deck to support the bottom Review the Installation Specifications illustration for your specific installation and note prov
10. OTISSERIE t ON LEFT SIDE zana B baza 2 51 OPENING FOR GAS SUPPLY CONNECTION BACK WALL LOCATION OR BOTTOM LOCATION NON COMBUSTIBLE ENCLOSURE lt 263 4 680 3 lt ROUGH OPENING 76 DEPTH min F 91 2 242 ROUGH OPENING HEIGHT 7 8 48 361 2 max R 927 2 51 DIAMETER OPENING FOR GAS SUPPLY CONNECTION BOTTOM LOCATION INSTALLATION INSTRUCTIONS 48 1219 GAS BBQ GRILLS INSTALLATION SPECIFICATIONS COMBUSTIBLE ENCLOSURE Built In Models 18 457 min lt 501 4 1276 gt lt 18 gt lt 273 4 705 gt lt 18 gt ROUGH OPENING WIDTH 457 min ROUGH OPENING 457 min E DEPTH A LOCATE lt 31 7 79 ELECTRICAL OPENING OPENING OUTLET FOR HEIGHT 33 4 95 HEIGHT ROTISSERIE ON LEFT SIDE 31 8 1 a 27 8 79 73 ALLOW OPENING ya 361 2 max o g l FOR ACCESS 2 51 DIAMETER OPENING 927 2 51 DIAMETER OPENING DOOR FOR GAS SUPPLY CONNECTION FOR GAS SUPPLY CONNECTION BACK WALL LOCATION OR BOTTOM LOCATION BOTTOM LOCATION COMBUSTIBLE ENCLOSURE Y NOTE Dimensions include insulated liner COMBUSTIBLE ENCLOSURE NON COMBUSTIBLE ENCLOSURE Opening Width 501 4 1276 Opening Width 48 1 4 1226 Opening Height 101 2 267 Opening Height 91 2 242 Opening Depth 273
11. al gas 7 17 5 mb WC Minimum line pressure for LP gas 11 27 4 mb WC Gas Supply Regulator To control and maintain a uniform gas pressure in the gas manifold the unit must be used with a gas pressure regulator The burner orifices etc are sized for the gas pressure delivered by the supplied regulator Do not remove the regulator A CAUTION The maximum gas supply pressure to the regulator should never exceed 14 34 9 mb WC 5 psi 3 5 kPa LINE PRESSURE TESTING Testing above 5 psi 3 5 kPa 14 34 9 mb WC gauge The BBO grill and its individual shut off valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures greater than 5 psi 3 5 kPa INSTALLATION INSTRUCTIONS BBQ GRILL COMPONENTS BATTERY INSTALLATION The porcelain coated cast iron grill grates are The battery powered ignition uses a AAA 5 127 wide for easy handling and cleaning battery provided with the BBO grill to be Below the heavy duty grill grates are the installed behind each ignition button stainless steel heat radiants located every 5 127 These radiants provided with the BBO grill are positioned over the grill burners to concentrate the heat Refer to the illustrations below To install or replace remove the ignition button by unscrewing in a counterclockwise direction Insert the AAA battery into the cavity with the positive end in first and replace the ignit
12. as BBQ grill model and serial numbers 800 332 9513 Both numbers are listed on the product Website rating plate located on the back panel of the grill wolfappliance com The information and images are the copyright property of Wolf Appliance Company LLC an affiliate of Sub Zero Freezer Company Inc Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Wolf Appliance Company LLC an affiliate of Sub Zero Freezer Company Inc Wolf Appliance Company LLC all rights reserved 19 s S 6 WOLF APPLIANCE COMPANY LLC L L 807578 12 2005 P O BOX 44848 MADISON WI 53744 800 332 9513 WOLFAPPLIANCE COM
13. becomes liquid when stored under high pressure inside a cylinder and it vaporizes when released LP gas is heavier than air Leaking LP gas tends to collect in low areas and could cause a fire or explosion It is important there are no leaking connections on your gas BBO grill Refer to the Gas Leak Testing on page 17 Manifold Pipe Regulator Shut Off Valve Adapt Regulator ad Close Nipple From Gas Supply Natural gas hook up Natural gas regulator INSTALLATION INSTRUCTIONS LP GAS CYLINDER CYLINDER SPECIFICATIONS Any LP gas cylinder used with this BBQ grill must be approximately 12 305 diameter and 18 457 high The maximum fuel capacity is 20 Ibs 9 1 kg or 5 gallons 19 L The full cylinder weight should be approximately 38 Ibs 17 2 kg which is 43 7 Ibs 19 8 kg nominal water capacity The LP gas cylinder must be provided with an approved overfilling preventive device OPD All LP gas cylinders used with this appliance must be constructed and marked in accor dance with the specifications for LP gas cylinders Always use the cylinder dust cap on the cylinder valve outlet during transport and when the cylinder is not connected to the BBO grill The LP gas cylinder provided with the grill is equipped with a quick connect closing 1 cylinder valve The valve contains a backcheck which is designed to prevent gas flow until it is connected to t
14. e of the connection will seal on the backcheck in the valve resulting in a slight resistance An additional 1 2 to 3 4 turn will be required to complete the connection Tighten by hand only Do not use tools If you cannot complete the final connection disconnect the regulator and repeat the last two steps If you are still unable to complete the connection do not use this valve and regulator Call your Wolf dealer or Wolf author ized service center to order the replacement parts A CAUTION DO NOT insert any foreign objects into the valve outlet The backcheck may be damaged A damaged backcheck can be the source of a leak Leaking LP gas may result in explosion fires severe personal injury or death Manifold Pipe Coupling Nut LP Gas Cylinder Coupling Nut Regulator Vent Points Down LP Gas Cylinder LP gas hook up LP gas regulator INSTALLATION INSTRUCTIONS GAS LEAK TESTING Perform a gas leak test each time the LP gas cylinder is connected to the regulator and any time part of the gas system is disconnected or replaced This applies to natural gas as well as LP gas Perform a leak test at least once each year whether the LP gas cylinder has been disconnected or not Test for leaks at the cylinder valve cylinder welds regulator especially attached to cylinder valves hose and connections NO SMOKING Do not use or permit sources of ignition
15. e possible shock hazard the cord must be plugged into a mating 3 prong ground type outlet grounded to conform with the National Electrical Code ANSI NFPA 70 latest edition or Canadian Elec trical Code CSA and all local codes and ordi nances Refer to the illustration below Do not cut or remove the grounding prong from the plug IMPORTANT NOTE You must have a properly grounded 3 prong outlet installed by a gualified electrician IMPORTANT NOTE Do not ground to a gas pipe IMPORTANT NOTE Keep the power supply cord and fuel hose away from hot surfaces Grounding Plug Grounding Type Electrical Outlet Electrical ground INSTALLATION INSTRUCTIONS GAS SUPPLY REQUIREMENTS A WARNING EXPLOSION HAZARD Use a new approved gas supply line and install a gas shut off valve Securely tighten all gas connections The maximum gas supply pressure to the regulator should never exceed 14 34 9 mb WC water column 5 psi 3 5 kPa Failure to do so can result in explosion fire or death IMPORTANT NOTE The gas BBO grill must be connected to a regulated gas supply Connect the grill to the gas supply line The gas supply line must be of adequate size to properly service all gas appliances VVolf recommends the use of a 1 2 13 I D commer cial type flex hose a 1 2 13 1 commercial type flex is the minimum size that may be used All plumbing to the flex hose MUST be 3 4 19 minimu
16. es must be observed Be sure the appliance is properly grounded to avoid shock hazard You must follow all National Electrical Code and gas regulations In addition be aware of local code or ordinances when installing your service Dimensions in parentheses are in millimeters unless otherwise specified COMBUSTIBLE SURFACES BUILT IN MINIMUM CLEARANCES A minimum of 18 457 from the sides and 18 457 from the back required above and below the cooking surface to adjacent vertical combustible surfaces A minimum of 6 152 to the side is required for space for the rotis serie motor Refer to the Overall Dimensions illustration for your specific model on pages 6 7 For exact rough opening dimensions refer to the Installation Specifications illustration for your specific installation on pages 8 9 IMPORTANT NOTE The optional insulated liner is necessary when the BBO grill is to be placed into a combustible enclosure Use only the approved insulated liner which has been specifically designed and tested for this purpose available through your Wolf dealer A WARNING Failure to locate the BBO grill without the proper clearances will result in a fire hazard ACCESSORIES Optional acces sories are available through your Wolf dealer To obtain local dealer information visit the Locator section of our website wolfappliance com WOLF GAS BBQ GRILLS 36 914 GAS BBQ GRILLS OVERALL DIMENSIONS BUILT IN
17. he regulator Keep the cylinder valve closed when it is not in use or attached to the grill LP gas cylinders are shipped empty for safety Allow only a qualified LP gas dealer to fill or repair your LP gas cylinder The gas dealer must purge a new cylinder of air before filling it Caution the gas dealer not to overfill cylinder After filling have the gas dealer check for leaks to see that the relief valve remains free to function Approximate running time for the 20 pound LP gas cylinder Models BBO242BI and 242 80 000 Btu hr 23 4 kW 51 2 hours Models BBO36BI and 6 69 000 Btu hr 20 2 kW 61 2 hours Models 62 1 and BBO362C 101 000 Btu hr 29 6 kVV 41 2 hours Models BBO48BI and BBO48C 89 000 Btu hr 26 1 kVV 5 hours Dimensions in parentheses are in millimeters unless othervvise specified TRANSPORTING THE CYLINDER Transport only one LP gas cylinder at a time Transport the cylinder in an upright and secure manner with the control valve turned off and the dust cap in place u Do not transport the cylinder in the passen ger compartment a Do not leave a cylinder in direct sunlight or in a high heat area such as a closed car trunk High heat areas could cause the relief valve to vent gas s Do not store cylinders in a building garage or any other enclosed area Store outdoors in a vvell ventilated area avvay from people The LP gas cylinder must be provided with a cy
18. ion button Refer to the illustration below The radiants are supported on each end by a pin located just above the grill burner Be sure the heat radiants are oriented so that the triangular cut out is positioned to the rear of the grill To make sure the sparker is operating press the ignition button and listen for a spark The Wolf BBO grill design eliminates the use of briquettes or lava rocks The grill burners produce 10 000 Btu hr 2 9 kW per burner j gt DN Grill Grate A WS SN e3 SN SN SS N IBS NA s N N Burner Insert battery behind ignition button T BBO grill components Radiant positioning Location of battery Dimensions in parentheses are in millimeters unless otherwise specified 13 14 WOLF GAS BBQ GRILLS NATURAL GAS HOOK UP For Wolf natural gas BBO grill models hook up is made from the rear right side with the fittings and regulator shown The coupling pipe nipple street elbow and regulator are provided To hook up the fittings refer to the illustrations below Make sure the flow arrow on the regulator points in the direction of the gas flow from the gas supply to the BBO grill LP GAS HOOK UP Wolf BBO grills set up for use with LP gas come equipped with a 5 1 5 m hose regula tor and an unfilled 20 pound LP gas cylinder LP liquefied petroleum gas is sometimes called propane butane or bottled gas t is a flammable gas which
19. isions required for the gas line hook up at the rear right and bottom surfaces It is recommended that ventilation holes be provided in the enclosure so that gas will not become entrapped in the event of a leak The supporting deck and counter should be level and flat The enclosure should be strong enough to support 400 Ibs 181 kg LOCATION CONSIDERATIONS When deciding where your permanent built in location will be consider the following Keep gas lines as short as possible The BBO grill should be level and not exposed to the wind Never locate the BBO grill in an enclosed area such as a garage shed breezeway or under overhead combustible construction Keep clear of trees and shrubs Optional insulated liner must be used if installing into combustible material m Allow adequate area for smoke to dissipate Allow for an adequate supply of fresh air for proper combustion and ventilation a Examine foot traffic patterns and service ability of the unit if necessary INSTALLATION INSTRUCTIONS INSTALLATION CONSIDERATIONS Safe and satisfactory operation of your Wolf BBO grill depends upon its proper installation The installation adjustments and service of this grill must be performed by a qualified installer service agency or gas supplier This is necessary to ensure proper operation and avoid accidents which may occur through misuse of the BBO grill All minimum clearances to combustible surfac
20. linder connection device compatible with the connection for outdoor cooking appliances A WARNING Handle a filled cylinder with care The LP gas in the cylinder is under high pressure 15 16 WOLF GAS BBQ GRILLS LP GAS REGULATOR ATTACHING THE REGULATOR The pressure regulator and hose assembly supplied with this appliance must be used The pressure regulator and hose assembly provided is factory set at an outlet pressure of 10 25 mb WC 4 psi 2 8 kPa The BBO grill regulator is equipped with a coupling nut Refer to the illustrations below Do not attempt to connect to any LP gas cylinder not equipped with a mating quick connect closing 1 cylinder valve The coupling nut connects to the large outside thread on the valve outlet To complete the connection follow these steps Make sure all grill burner valves including open burner and rotisserie if so equipped are in the OFF position a Make sure the cylinder valve handwheel is in the closed position Turn clockwise left to right to full stop a Remove the protective caps from the cylinder valve and coupling nut Hold the regulator in one hand and insert the nipple into the cylinder valve Be sure the nipple is centered in the valve outlet Hand tighten the coupling nut Do not cross thread the connection a Turn the coupling nut clockwise left to right to tighten to a full stop IMPORTANT NOTE In the connection process the grill sid
21. m D pipe IMPORTANT NOTE For complete gas shutdown an external gas shut off valve must be located near the appliance in an accessible location Refer to the illustration below SHUT OFF VALVE Open Position Gas Supply To Appliance Line Shut off valve Dimensions in parentheses are in millimeters unless otherwise specified The Wolf gas BBO grill functions up to 6 000 1828 m in altitude without any adiustment If installation is above 6 000 1828 m contact your Wolf dealer A CAUTION Before connecting the gas supply make sure all valves are in a closed position Do not connect the gas supply line to an appliance that shows any sign of physical damage IMPORTANT NOTE This installation must conform with local codes and ordinances In the absence of local codes installations must conform with the American National Standard National Fuel Gas Code 11 12 WOLF GAS BBQ GRILLS GAS SUPPLY REQUIREMENTS GAS MANIFOLD PRESSURE For Natural Gas Standard orifices are set for 5 12 5 mb WC water column A natural gas pressure regulator is included For LP Gas Standard orifices are set for 10 25 mb WC water column An LP gas pressure regulator is connected to the hose provided with the grill Gas Supply Pressure For checking the regulator setting the maximum line pressure for natural and LP gas 14 34 9 mb WC 5 psi 3 5 kPa Minimum line pressure for natur
22. ol knob to the on position to release pressure in the hose and manifold Turn OFF the control knob A WARNING Do not store a spare LP gas cylinder under or near this appliance Never fill the cylinder more than 80 full If this information is NOT followed exactly a fire causing death or serious injury may occur 17 18 WOLF GAS BBQ GRILLS INSTALLATION CHECKLIST IMPORTANT NOTE To ensure a safe and proper installation the following checklist should be completed by the installer to be sure that no part of the installation has been overlooked Any questions or problems about the installa tion should be directed to your Wolf dealer or the Wolf Customer Service Department at 800 222 7820 You can also visit our website at wolfappliance com All internal packaging has been removed All shipping restraints have been removed from the burners Radiants are oriented properly over grill burners with triangular cut out positioned to the rear of the grill Specified clearances to any combustible materials have been maintained Batteries are installed behind the ignition buttons All burners light properly individually and with adjacent burners lit All flames appear normal The drip tray slides freely and the grease collection tray is properly placed The correct pressure regulator is connected for natural or LP gas and set for 5 12 5 mb WC for natural gas or 10 25 mb WC for LP gas The LP gas cylinder is
Download Pdf Manuals
Related Search