ANGA H.264 Standalone DVR
Contents
1. User Characters in length up to 8 bytes ignore trailing Spaces Can be letters Numbers and other symbols The user has the largest number of eight user name may not be repeated User Rights According to the requirements set of functions need checked Add User Input need to add user and input the account password and passwords According to save button to add user Delete User Select the users need to delete and click on the yes button to remove users Edit User Choose need to modify user and in user permissions bar needed under the function of check According to the save button modified users Edit Password Select the account input to modify current user password and enter the account password and confirmation password new According to the save button for password changing The password can be set to 0 8 bits 4 Alarm Setup Alarm Input Input Type Management Clear Alarm User PTZ Relate Management Send E mail Trigger Recording Output Schedule Alarm Output Alarm Input Choose corresponding alarm channel all setup all channel said Input Type Alarm input to often open closed type choice voltage output style 32 Clear Alarm Stop the current alarm video and alarm output but not removal can again trigger alarm PTZ Relate When will the linkage happened alarm yuntai control Trigger Recording When will trigger happened alarm selected channel video Alarm Output When will the lin2. 2 1 3 Alarm input port ALARM IN 16CH alarm input port 8chanel alarm input the mode of alarm input is no restriction possible is normal open also normal close RS 485 A B R5485 S A B the GND alarm detector connect to COM under parallel connection the power of alarm detector supply by external power supply the ground terminal of alarm detector join up in parallel with DVR ALARM OUT N1 N fer alarm output port every channel connect Cando port is for GND the NC of alarm detector connect with the input end alarm of DVR when you want to reset the remote alarm of triggered the 12V power supply of alarm detector supply by DVR for example smoke detector When you select the external power supply please share the GND with DVR Alarm input circuit Vec Vec R R 4 7K 2 2K 1 yy a 2 Alarm out GPIO out Alarm in connection alarm device me byr alarm in 2 1 4 Alarm output port 4 way switching value alarm output selectable in normally open contact also selectable in normally closed alarm outgoin contact the external gong alarm device should COM be need Vcc RELAY Chapter Three Operation 3 1 Operation instruction 3 1 1 Remote control AND Front panel keypad 11 wji ALARN CLEAR KEYpad Keypad Name Operating instruction Name Operating instruction POWER Power ON OFF MENU S N 8 Exit operation or enter upper menu Close soft keyboa
3. catastrophe failure in network it will cause the DVR reboot repeatedly 05 Why does the system halted of DVR during the playback and search the video file information in progress fr Please check if you install the hard disk drive or if the drive is ok or not Please replace the good one for it soon fr If the ambient temperature on the high side or not fr Is there any heaven current installation surrounding and external video device heavy current surging video cable caused the DVR can not work properly and the system halted 06 Firmware upgrade failure U drive is not good compatible with the DVR cause the DVR can not detected it suggested to try one or two more different kind of U drive in the market USB interface is not good fr The voltage hunting fearfulness during the system firmware upgrade in progress e 07 Why the display color is black and white in TV and VGA monitor fr Check the video system is it matching the video input DVR TV or VGA monitor if there is not on all fours please set the video system mode in auto automatic recognition 08 Why does nothing display on the TV or VGA monitor please make sure if the power supply of TV or VGA monitor turn on or not if the illumination located in the lowest status GH the video connected with TV or VGA monitor properly Check if there is any video signal input 69 And make sure the line faulty or not 09 Why does the video l
4. Installation and operation instructions 6 1 3 2 Installation and operation instructions 1 Run the App Store program of iPhone dei 54 Switch to the search tag page and input Asee in the search box to find the application installation package then click lt install gt After finishing installation there will be Asee program icon on the mobile phone desktop as shown in A lt PTZ control PTZ direction control including up down left and right Zoom in out control of PTZ the below image v gt Focal length Focal length adjustment of PTZ Aperture Aperture control of PTZ PTR ee Za ra we ae le E g amp 2 Click the program icon Asee and the initial interface after running procedure is shown in the above image 3 Initial usage of need to change the parameter The corresponding functions of buttons show as follows panna usag g p SE 1 Please click the settings button EJ and enter the device manage interface as shown in the below image Function keys Definition Function specification Stop a When the program disconnects with device stop playing the video playing Capture the current image the default save path the default pictures Capture directory of mobile Set some information of the device such as IP address dynamic domain Settings name port username password and device alias information Back Device Manage Add Cancel Some device information of the software Choose on
5. Setup Ethernet Setup PPPoE amp 3G a ns Email Access Control Auto Start IP Address 6 6 D sen Dial Type Wireless 3G Account Password ISP User Define APN Conection Num DDNS Service DDNS Domain User Password DDNS Service Dynamic DNS provider website Via DDNS server it compatible with SODDNS ANYVISION PANSIM DYNDNS ORG if you select soddns you can customize your favorite domain name it shows as following picture 28 Ethernet Setup PPPoE amp 3G Email Access Control DDNS Service DDNS Domain User Password Release Binding DDNS Status DDNS online 9 400 77227 Internet IP 58 100 72 22 DDNS Domain Dynamic domain name soft keyboard and hard keyboard can be input DDNS Account Login domain name service provider website user name DDNS Password Login domain name service provider website password Tip through the dynamic DNS server Support dynamic DNS 4 E mail Ethernet Setup PPPoE amp 3G DDNS Setup Access Control E SSL Protocol Email Address 1 Email Address 2 Send Email SMTP Server SMTP Port Email Account Email Password Test Email also choose Note your sender email must support SMTP 5 Access Control Ethernet Setup List Rule PPPoE amp 3G DDNS Setup Starting IP Ending IP Email Add Not Used SN StaringIP EndingiP Delete List Rule According to the requirement
6. for the better service 73
7. phone screen resolution is 480 360 and 480 320 Support 8900 9000 9700 9630 9900 of Blackberry 2 Support DVR platform versions gt Hisilicon v1 0 1 8 and higher gt GRain v8 33 and higher 2 2 Installation and operation instructions 6 1 2 2 installation 1 Install ASee cod and ASee jdp installation package into Blackberry handset through the desktop manager as shown in the below image 3 57 PM edge ail CHINA MOBILE About 7 Downloads Advanced Options Auto On Off AutoText Bluetooth Custom Dictionary Date Time Language and Text Input Memory MMS Mobile Network D 2 Click the options on mobile phone desktop and enter the interface of the above image 3 lt Asee gt permission settings a Click lt application program gt to find out p lt Asee gt b Click the icon of lt Asee gt and enter the permission settings c Click lt edit permissions gt set all permissions lt permit gt Note Some permissions can not be set lt permit gt the gray options mean cannot change this option and click save 4 Enter the initial interface Click the program con S lt Asee gt after running procedure there will be an welcome page then enter the initial interface as shown in the below image 50 Setting 5008 128 0 254 108 6088 admin Networktyp EMM Login Exit DeviceList Notes gt lt Title gt It is convenient to distinguish between multipl
8. platforms is shown as follows User login 2012 06 15 User login 2012 06 15 1 Android Net setting 2012 06 15 User login 2012 06 15 2 Blackberry User logout 2012 06 15 User logout 2012 06 15 kt 3 iPhone User login 2012 06 15 Wet o oc o sn os Mu IN1 9218 16 4 Symbian Download 6 1 1 Instructions of Android 6 1 1 1 Essential condition 1 Support the version 1 5 or above of Android system 2 Support DVR platform versions Chapter Six Instruction for mobile monitor _Hisilicon v1 0 1 8 and higher 1GRain v8 33 and higher 6 1 Asee 6 1 1 2 Installation and operation instructions 1 Installation This module has mainly instructions on the installation and usage in Android Blackberry iPhone mobile phone Support two installation modes and the user can choose one way for installation 1 The acquisition of client software The client software can be got from the CD material equipped with CD then choose English and select the options 1e insa oning supporting tools finally choose the mobile phone monitoring or obtained from technical support Each type of Search ASee on google market and install online As the below image shows corresponding client software as follows 1 Asee apk The smart phone monitoring client of Android operating system 2 ASee cod amp ASee alx The smart phone monitoring client of BlackBerry operating system 3 ASee sisx The smart phone monitoring client of Symbian operating
9. set the channel will be showed the mark on everyone channel Manual recording Note Manual recording operational requirement the user should have recording permission Please make sure the hard disk drive has been installed and it has been formatted 1 Input manual recording operation menu Single click right key of mouse or In main menu gt recording control can into manual recording operation menu Under preview mode press REC key or on the Remote controller unit key into recording control operation menu as follows Recording Control All Automatically Manual Rec Stop Rec sn Gen 2 The explanation of manual recording operation menu manual recording Priority level highest no matter currently what status of every channel after carry out the manual press corresponding channel will be record common in progress Auto recording Setting channel recording by setting condition to record under Timing Motion detection and Alarm in Recording Setting Stop Recording All video channel stop recording 17 3 7 Playback video h X 00 00 04 00 08 00 12 00 16 00 20 00 24 00 PTET ETT TTT TEE ET EE EEE a i 44 a gt b gt r m 0 2011 02 26 00 00 00 SG A Descri Description Descri Description Synchronous asynchronous play Voice adjustment El frame by frame SS 1 4 8 9 16 24 32 e screen switch image Fj Speed slow Hide display list mm Speed normal recording date Note 1 Du
10. ANGA H 264 Standalone DVR USER MANUAL Ver 3 00 DIGITAL VIDEO RECORDER Chapter one Products Introduce anurnnnnrnnnnnnnnnnnnnnnvnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnnusnnn 4 Te AP E 4 VPN 5 Chapter Two ge UE 6 2 1 H 264 standalone 4CH 8CH 16CH 24CH 32CH DNR 6 Chapter Three Opera av 4 11 3 1 Operation ENN 11 PENN NN 14 elen EE 16 3 4 Multi Channel RE EE RE ER EE EE EN 16 PAN 16 3 6 Recording Kee e ttre ttrrrrrrr rtn rESrEr EEEE errr rrn Er rreren 17 3 7 Playback video WE 18 3 8 How to GONE ONE EEE AN 19 3 9 Alarm control EDR EEEEEeg 20 TN 21 Chapter Four Menu Operation Guide r nnnrnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnunnnnnnennunnnnner 22 FEN 22 AG gt E 24 4 NNN Gro 0 Semen meer nee ee ater ene net mn ne ner nee Ce eee ere E AE cree 26 44 System SetUP E 30 4 5 System Management 33 Chapter Five IE EE 36 5 1 logging on interface EN 36 5 2 System AN 37 ul de EE 40 Chapter Six Instruction for mobile monitor nnxrnnnarvnnnvnnnnvnnnnnrnnnnnnnnnnnnnnnnnnnn 43 O TASEGO REE EE ee me re a ENER EE AN een re eee er nee 43 6 1 1 Instructions of Android E 44 6 1 2 Instructions of Blackberry 50 6 1 3 Instructions of iPhone eene eege 54 6 1 4 Instructions OS 60 Chapter Seven Instructions Of IMAC rnnnnrnnnnrnnnnnnnnnnnnnnnnennnnnnnnnrnnnnnnnnnnnnnunnnnne 64 ENN 64 7 2 Installation and operation instructions nnenneneeanoeneeneeneenertrererrrrrtrrrrrrsrrerrrrrrerrenene 64 Chapter E
11. DVRIB gt MY DVR 4 DVR Title MY DVR 8 Server 128 0 5 4 Part AD User Name admin Password Max Channel H Ok Delete Cancel Notes cack AR Back to the screen of previewing image gt lt Channel List gt It shows the corresponding DVR and the default channel list the user can arbitrarily choose a channel to preview image gt lt Information Edit gt Click this button and enter the Settings interface you can editor delete the device information as shown in the above image 6 Complete settings choose channel to preview and the preview function include two modes common mode and full screen mode 1 Common mode is shown in the below image 48 MY DVR 8 2 Full screen mode is that when mobile phone lay down horizontally it will automatically switch to full screen mode as shown in the above image 7 Channel switch function Select some channels in the Device List interface the program will automatically switch to the Preview Interface and open the corresponding channel preview in Preview Interface Program displays the default 1 4 channels if the user clicks the channel button ES of Next Group in the Preview Interface the channels group will switch to 5 8 8 12 12 16 and circulation switch As shown in the below image 49 6 1 2 Instructions of Blackberry 6 1 2 1 Essential condition 1 Support the version 4 6 or above of Blackberry system and mobile
12. Internet RJ45 10M 100M PAL 1 25P S NTSC 1 30P S Manual record motionrecord and externa alarm record Record Play Internet HDMI 1080P 1920 108 0 RJ45 10M 100M 1000M PAL 1 25P S NTSC 1 30P S Manual record motionrecord and externa alarm record Record Play Internet HDMI 1080P 1920 108 0 RJ45 10M 100M 1000M PAL 1 25P S NTSC 1 30P S Manual record motionrecord and externa alarm record Record Play Internet HDMI 1080P 1920 108 0 RJ45 10M 100M 1000M Naway CAB symbian v3 symbian v5 Naway Android iphone Blackberry RS485x1 USB2 0x2 SATAx1 2 maximum 2T Usb mouse Usb disc backup usb RS485x1 USB2 0x2 SATAx1V2 maximum 2T Usb mouse Usb disc backup usb RS485x1 2 USB2 0x2 2 4SATA maximum 2T Usb mouse Usb disc backup usb 71 RS485x1 2 USB2 0x2 2 4SATA maximum 2T Usb mouse Usb disc backup usb RS485x1 2 USB2 0x2 2 4SATA maximum 2T Usb mouse Usb disc backup usb mobile hard disk mobile hard disk mobile hard disk mobile hard disk mobile hard disk Power adapter Working temperature Working humidity Product size mm Product weight Kg 12V 3A DC 12V 3A DC according to according to the sum of DISK the sum of DISK 0 C 60 C 0 C 60 C 10 90 10 90 330x250x50mm 330x250x50mm accor
13. Output Open the corresponding alarm output All Can choose all the channels 20 3 10 Display Adjust 1 Video Video Monitor Video Effect Video Effect Optional standard downy sharp custom Default Restoring default effect for custom video effects copy standard effect parameters Through the slider fluctuation sliding respectively adjustable brightness contrast and saturation tonal etc 2 Monitor Monitor Device Optional VGA output TV output etc display output device Default Restoring default display parameters Through the slider fluctuation sliding respectively adjustable brightness contrast and saturation tonal etc 3 Setup 21 Video Device Resolution Monitor Setup Adjust Resolution Device Optional VGA output TV output etc display output devices the system may support multiple equipment and output Resolution Setting the resolution of the display device Chapter Four Menu Operation Guide 4 1 Recording Setup 1 Recording Setup Sub Stream Channel Overlay Recording Schedule Channel Encoding Type nd Frame Rate mr Encoding Mode Image Quality Common v Digital Watermark ME Pre Alarm Rec Close v Channel Choose the need to install passage whole says setting all channels Image Size CIF HALF D1 D1 only in whole function model Encoding Mode Including fixed bitrate dynamic bitrate Image Quality Client side imag
14. P address is 192 168 0 20 36 Setting 2012 06 15 10 57 39 EES 1 Live01 192 168 0 19 2 Live02 192 168 0 19 3 Live03 192 168 0 19 4 Live04 192 168 0 19 User Info Network setting Common setting GUI Language English vi Reeg i 1 0 10 etd 3 3 Le Video window color BEE phi stretch 5 Live01 192 168 0 20 6 Live02 192 168 0 20 7 Live03 192 168 0 20 8 Live04 192 168 0 20 Directory ID NetDvrV3 Re c Reserve Disk Space M gt 100 Auto divided duration os min 5 120 H 264 Eabedded DYR H 264 Embedded DYR H 264 Embedded DVR H 264 Embedded DYR EP Whew disk te Tuli ZA vo d Ee 2 S Capture Setting Directory Reserve Disk Space H 264 Embedded DVR H 264 Embedded DYR H 264 Eabedded DVR H 264 Embedded DYR Downloading Setting 9 16 25 36 64 Directory Reserve Disk Space Channel Switch Switch timer 5 2 System Settings W Full display when channel alarm Setun GE teen erch Point 4 As the picture You can set up language directory After all to save you set 37 38 Setting Setting Local setting Network setting Common setting Encoding setting Sub Encoding setting Record Setting ding setting PIZ Setting Alarm Setting Video detect Video loss User Info Output Manage Auto Window Preview Output Manage Auto Window Preview Channel Channel 01 v Protocal Pelco Di D Baudrate larm output Data bit Stop bit Parity H Alarm Relate PTZ Channel Lamm
15. Relate PTZ Parameter O 00 UU 00 00 Save all Save all L 5 3 State control In state control you can set reboot server close server remote to go up Remote upgrade let PC file load in the system Log to inquire sometime the server s action 39 40 Status control Status control Online User teecord Control Control Comm ot Video Online User Record Control Alarm Control Channel 01 Brightness Reboot server Chroma Shut d e ua Server Contrast Saturation Remote upgrade 41 Status control The mobile phone client of apple mobile phone system iOS can be directly searched for ASee in the appstore and installed online The mobile phone client of Android system can be directly searched for ASee in the Android market and installed online End time rome Oprat Abnormal z 2012 06 15 A i Gas i A A nri HETTE TER 2012 06 15 2 The main functions of the program which is straight even version of current mobile phone monitoring are shown as User login 2012 06 15 Net setting 2012 06 15 10 29 follows User login 2012 06 15 ENE 2012 06 15 10 51 1 Browsing real time video function In addition to BlackBerry it can support four pictures at the same time preview User login 2012 06 15 Net setting 2012 06 15 2 PTZ control function the controlled ball machine is in front User login 2012 06 15 System reboot 2012 06 15 System pow 2012 06 15 ser ret MEET 3 The instructions of three
16. Set Click Start Tour the trajectory of said no corresponding click the add Preset and delete Preset point I Clear Tour the cruise lines Start Tour begin to track record was registered date end Tour thus set up from the corresponding track circuit 19 Left Limit Began to limit scanning Settings was registered date right Limit thus set up corresponding limit scanning Add Preset Add presets point to the cruise lines Delete Preset Cruise lines from deleting preset points Clear Tour Remove the cruise line designated Note some equipment doesn t fully support all function depending on the specific yuntai equipment and different Normal Control x Control t Open Aux Tour Scan Close AUX Patteri Scan Limit Scan PTZ Reset Auto Pan Control PTZ Control Tour Scan Point between cruise control Pattern Scan Track patrol control PTZ Reset Remove all Settings original reset to the original state Limit Scan Yuntai boundary scan control around Auto Pan Remove the cruise line designated Note some equipment doesn t fully support all function depending on the specific yuntai equipment and different 3 9 Alarm control Alarm Control Set Alarm Clear Alarm Alarm Output wm 1 Gu Set Alarm Selection need protection channel click confirm corresponding channel after in protection status Clear Alarm Remove protection condition not alarm input to react Alarm
17. Symbian 6 1 4 1 Essential condition 1 Support the version OS S60 or above of Symbian system 2 Support DVR platform versions e Hisilicon v1 0 1 20 and higher e GRain v8 42 and higher 6 1 4 2 Installation and operation instructions Installation Support two installation modes and the user can choose one way for installation 1 Install online Search ASee on google market and install online 2 Install offline Copy the Asee sisx installation package to Symbian phone through cable In the specified directory find out the corresponding sisx click the application installation If there is not installed apk installer in the mobile phone the user needs to download an apk installation software so that it can identify the sisx package and there will be program icons after finishing installing As the following figure shows pr DH 2 Click the program icon p 4 lt Asee gt the first screen after running is shown in the following figure 60 Connecting Petras iM click PTZ show as the following figure el 8 ur Connecting HETEN ai The functions of buttons show as follows Play pause When the program connects with device play video Capture the current screen the default save path the default pictures directory capture of mobile 61 Set some information of the device such as IP address dynamic domain name settings port username password and device alias information For this channel full scr
18. ation the DVR will be damaged in serious In this surroundings suggest select the stabilized voltage supply Configuration wizard provides common Welcome to configuration wizard funciton parameters The wizard will help you to set various of ie 3 4 Multi Channel settings will help you parameters and task schedule to administer and Please click NEXT to continue deploy systems more efficiently and please look at the main Standard User menu if needing more Professional User information of configuration Language English kd Display on startup Next Apply 1 4 8 9 16 24 32 preview screen mode switch 3 5 Preview After log in system of DVR system will automatically directly enter the preview mode In the preview picture you can see the overprint date time channel name if the date and time is not correct show on the picture re setting the date There is a alarm input mode icon the meaning of every kind of icon as following 15 16 table Channel picture attention Channel happen when dynamic test channel video pictures showed this symbol Channel is video when channel video pictures showed this symbol Channel happen when channel video cover alarm pictures showed this symbol Channel open sound the channel video pictures showed this symbol 3 6 Recording operation Customer can according to select the different kind of recording mode in this system For the different kind of recording mode you
19. be downloaded by Client software through LAN to laptop hard disk drive through network to real time remote monitoring PTZ control recording research and real time playback system setting parameter modify and the system software upgrade remote monitoring alarm process and view the system log message to use embedded TCP IP protocol and Embedded Operation System can access the DVR through client software program bundle in the package Management Model use enhancement user management password mode to make sure the valid user to login the system flexible convenient and fast to set the different permission user Alarm linkage function PTZ control 8ch alarm input alarm event mode can be set normal open or normal close selection and turn by turn video loss alarm dynamic detection alarm the alarm device may be smoke detection censer temperature detector IR detector Possess Ach relay switch alarm output flexible convenient and fast to achieve alarm linkage and lighting control at site They re possess protective circuit in Alarm input and alarm output port make sure the device not to damaged Support PTZ decoder through RS485 communicate scalable multiple decoder protocol easy to achieve to control the pan driver and speed dome camera function Com munication port Intelligent operation Chapter Two Hardware Possess specific interface achieve alarm input and PTZ contr
20. c LAN IP access The dvr support model Unicom huawei E173 zhongxing MF 100 Telecom huawei EC150 huawei EC 156 zhongxing MF583 3G DIAL have two modes with automatic and manual dialing the operation follows as below 1 Automatic Dialing Select the Automatic Dialing in the interface of the following picture fill the right information according to the operator where the 3G card belongs to and the 3G referred guide It includes IPS names AP dial telephone ID and password the interface shows as the other following picture some IPS once be chosen the other relative information has been already done so you needn t fill any more click SAVE directly Then click Save directly After having detected the 3G signal when DVR start the system will dial up automatically 2 Manual Dialing In the interface of following picture users would fill the right information in the menu bar as same as Automatic dialing and click SAVE Then click Dial up after saving successfully The referred information would be saved still after the DVR restart but you should click Dial up again In these two modes if the dial up want success first you should make sure that the 3G card is available Since 21 the 3G signal has been existed the related menu bar will show the correct IP address if failed system will popup a window to show the wrong information C Ethernet Setup DDNS Setup Email Access Control 3 DDNS
21. deo Loss Send E mail Alarm Output Video Mode Provide PAL and NTSC both formats video formats choice modify after you must restart your system can take effect Channel Choose to set the video Settings area passage whole says setting all channels Reserved Section Click Settings enter The white areas for privacy area Buzzer Alarm Happen when video lost choice whether or not to allow buzzer warning Alarm Output Happen when video lost upcoming linkage selected channel corresponding alarm output 3 Motion Detection PTZ Setup Channel Channel 01 vm Senn Seting M Video Setup Detection Area g e men icia a Buzzer Alarm Detection Send E mail TESE SEQ Display Trigger Recording Alarm Output hpne E Channel Choose need to set up mobile testing area passage whole says setting all channels Sensitivity Setting Can be set to give minimum low general high highest 25 Detection Area Click Settings enter Green area for dynamic test grey areas design ferroconcrete brick undefended area for Press the mouse left key to drag on the lower detection area to the right press the mouse button clearance Detection area drag The save and exit button can save Settings some give up and quit button abandon modification Buzzer Alarm Occur when dynamic test on the buzzer whether to allow the alarm Trigger Recording That will happen when dynamic test on the linkage of select
22. ding to according to the sum of DISK the sum of DISK 2 6 without disc 2 6 without disc 12V 5A 6ADC according to the sum of DISK 0 C 60 C 10 90 380x300x55mm 3 0 without disc according to the sum of DISK Attention Parameters vary depending on the model T2 12V4A 5A 6ADC according to the sum of DISK 0 C 60 C 10 90 440 360 70mm according to the sum of DISK 3 46 without disc 12V4A 5A 6ADC according to the sum of DISK 0 C 60 C 10 90 440 360 90mm according to the sum of DISK 3 52 without disc PRODUCT WARRANTY CARD All the products sold are covered by 12months warranty from the date of invoice Warranty instructions 1 Please contact us when the product is caused by its own fault within 1year warranty 2 Please mail us your written warranty card as soon as possible after purchasing our products so that we can repair or replace this product to its original operation condition Or the company will not deal with it 3 Please write the truth on the warranty card 4 Paid for repairing as follows A Equipment failure caused by human operation B Equipment failure caused by not conforming to the using environment C No warranty card D Warranty expired Product model Product serial number Purchasing time User name Contact person Telephone Note Please keep the warranty card
23. e channel video of the broadcasting equipment And cooperate Select channel with next group can achieve the switch of 8ch and 16ch 2 Then select Add button and enter device add interface as shown in the above image E Channels group switch It can switch to next channels group D o 2 4 Notes 55 56 lt Device Name gt It is convenient to distinguish between multiple devices lt Address gt The public IP address dynamic domain name or LAN IP of DVR The port should be mapped before using public IP and mobile phones need to open wifi before using LAN IP lt Port gt The mobile phone port set in DVR default parameter is 8888 lt User ID gt The username permitted to login the DVR default username is admin lt Password gt The password of the user default password is empty Y v V WV lt Max Channel gt The actual channel number of DVR 3 After finishing click lt OK gt enter lt Device Manage gt interface As shown in the below image Back Device Manage CJ DVR 4 ee 4 In the lt Device Manage gt page click the lt back gt button enter the lt add channel gt interface then click the lt gt hl as shown in the above image 5 Click the lt gt mo and switch automatically to lt Device List gt as shown in the below image 57 gt DVR 4 Y DYR 4 channel 1 channel 2 channel 3 channel 4 6 Click the button GC to view all cha
24. e devices gt lt Address gt The public IP address dynamic domain name or LAN IP of DVR The port should be mapping before using public IP and mobile phones need to open wifi before using LAN IP lt Port gt The mobile port set in DVR default parameter is 8888 lt Channel total gt The actual channel number of DVR lt User ID gt The username owens view permissions of mobile phone default username is admin lt Password gt The mobile phone port of DVR default password is empty lt Network type gt Choose the network type that you need VV Y V Y WV The corresponding functions of buttons show as follows Function keys Function specification Enter the playing interface and the program will connect with Logi D device and begin to play video DeviceList Enter the device list interface 51 5 Click lt login gt play the main interface as shown in the below image 5008 Buffering The corresponding functions of buttons in lt Main interface gt show as follows Function keys Function specification Capture the current image the default save path the Capture default pictures directory of mobile It can select the next channels group 1 4 4 8 8 16 or Next group PTZ control Choose one video channel of the broadcasting device and Select channel select any one of 8 channels Up control of PTZ The up direction control of PTZ Down control of PTZ The down direction control
25. e quality the higher the quality the clearer Choice scope minimum low general high highest Frame Rate Can click on the button manually input 1 25 frames per second PAL or 1 30 frames per second NTSC continuous adjustable Audio Can select close open according to requirements Pre Alarm Rec Can select close open according to requirements 2 Secondary Stream 22 VAR Channel Channel 01 Setup Encoding Type Frame Rate Channel Overlay Image Quality ecording Schedule Channel Choose the need to install passage whole says setting all channels Image Size CIF HALF D1 D1 only in whole function model Image Quality Client side image quality the higher the quality the clearer Frame Rate Can click on the button to undertake choosing optional automatic 1FPS 2FPS 3FPS 4FPS 5FPS 3 Information Overlay Recording Setup Channel Channel 01 v Sub Stream Channel Display Lett v Time Display Not Used v Recording Schedule Channel Choose the need to install passage whole says setting all channels Channel Name Can manual corresponding input channel s name Channel Display Can choose according to the requirements of users don t use the top left corner left lower middle and downward upper right and lower Time Display Can choose according to the requirements of users don t use the top left corner left lower middle and downward upper right and lower 4 Reco
26. ed channel fast ball trigger video Alarm Output In this passage setting user can be copied to the other channels fulfill the same dynamic detection alarm Settings 4 3 Network Setup 1 General Setup Ethernet Setup DHCP UPnP IP Address 192 168 0 PPPoE amp 3G Subnet Mask 255 255 255 0 e SZT HUEN 192 168 0 1 pg DNS Server 202 96 134 133 Server Port 17777 HTTP Port Email Access Control Handset Port a MAC DHCP After checked automatic assignment device will get IP address subnet mask the default gateway the DNS server etc UPnP Can choose according to the requirement 26 IP Address Network logic address can according to the requirements set Subnet Mask Server subnet mask Default Gateway Server gateway DNS Server DNS server addresses Server Port Data port initial socket for 7777 HTTP Port the default port for 80 If change when using IE browser need to monitor the IP address adding new socket If use IP address to 82 from the original browsing http 192 168 0 19 change for http 192 168 0 19 82 Handset Port Network phones socket initial socket for eight thousand eight hundred and eighty eight 2 Dial UP Setup y f Auto Start IP Address Ethernet Setup Dial Type DDNS Setup Password Email Access Control Tip PPPoE dial up successful according to PPPoE IP shown on IP address users can remote access hard disk video recorder By ni
27. een Pervious to the former channel next to the latter channel quit current software Choose one video channel of the device And cooperate with next group can Select channel switch the 8 or 16 channels Ptz PTZ control PTZ direction control including up down left and right Zoom in out control of PTZ Focal length Focal length adjustment of PTZ Aperture control of PTZ LN VK br 3 If it is first running or need to change the parameters please click the lt settings gt button and enter the lt Device List gt page as shown in the following figure 62 y Setting e I 6 79 1 IP 128 0 254 2 Port Chapter Seven Instructions of imac B888 3 User Name 7 1 Essential condition admin Options a 11 57 3C 1 Support the version OS X 10 6 3 or above of imac system y Setting z a z 2 Support DVR platform versions ee User Name a Hisilicon v1 0 1 20 and higher admin b GRain v8 42 and higher Password Er 5 e 7 2 Installation and operation instructions None F Sach 5 Alias One method None To unzipped the Asee app in windows xp os copy it to the mac machine and then you will find the icon Options pa 11 52 The other method Notes Download from App Store Search for Asee find the corresponding program installation package Asee apk 1 lt server address gt The public IP address dynamic domain name or LAN IP of DVR The port should be mapped installation package install o
28. ight FAQ Frequently Asked Questions r nnnrnnnnrrnnnnrnnnnnnnnanennnvrnnne 69 1 e Power This DVR select the adaptor is DC12V please make sure the power supply voltage before use the machine If long time do not use the machine please turn off the power of DVR machine and let the electric plug away from power socket e safety This DVR only for indoor use as for prevent short circuit or electric danger please do not let the DVR in the raining or humid area In case any solid or liquid inside the case of DVR please turn off the power immediately and ask the qualified technician check it before reboot the DVR The DVR is the precision machine there is nothing for repair by customers themselves in it when it break down please ask the qualified technician to check and repair or contact with the agents of it e Installation Please keep the DVR in level for installation Pay attention to equipment ground For the first time to install the DVR please make sure if the hard disk drive install or not Prevent to open the case and change the hard disk drive in electrified Propose to select the performance of hard disk drive will be 7200 rotating speed person second Please select the appropriate installation site so let the air can be free flow inside the DVR prevent the machine overheating Please do not install the DVR nearby the radiator air chute etc heat source or where the direct sunlight too much dust or mechanica
29. ike water wave to appear obstruction distortion fr r f Oif there is short circuit open circuit or insufficient solder and connection failure of video cable GH the video cable obstruction by high voltage interference please separate the video and high voltage in linkup cabling at the meantime please select the better quality shield video cable for the project In the whole system only select the central point to grounding please do not multi port to grounding then cause the common mode obstruction please connect the screw in DVR rear panel to grounding r Check if there is the become old problem in the camera or TV monitor and cable e 10 Why do the color of live video and record video data distortion Make sure the input and output video parameter of main menu setting correct r amp Make sure the connection is correct 11 Why does the video skew became deformed color cast Make sure the VGA cable and DVR be connected with grounding properly r amp The DVR working atmosphere temperature high or no good in radiating cause the VGA chipset working exceptional or the mention circuit parameter is abnormal e 12 Why does the record video playback in mosaic under local DVR r d raising The recording parameter setting is too low cause the record video quality overall down sometime appears to mosaic The record video file locates where there is a bad sector in a ha
30. kage happened alarm corresponding alarm output 5 Output Management Hardware Version 0 0 0 0 200000 Sg Software Version 0 0 0 0 Log Search Serial Number Ven Online Users Release Date Exception Software Upgrade 12 16 20 24 ANE 8 Buzzer Output AMIN 11 Handling HDD Default Management Send Email Mn User Alarm Output HUDD Management Show the system hardware versions software version release dates Click software upgrade the system Alarm Setup began to automatically detect and upgrade file aS Note equipment currently support upgrades local USB mode IE mode the client software USB mode former ensure USB device to connect upgrade normal as upgrade program has copy USB devices in the root directory According to the interface can upgrade operation hints Upgrade was successful and the screen appears to restart operating hints Equipment reboot after system that will enable the new software Buzzer Output In the chosen time intervals have alarm input will start buzzer output Send Email In the chosen time intervals have alarm input which will send relevant information such as the alarm events paparazzi pictures equipment name device ID etc sent to user specifies the mailbox 2 Log Search Alarm Output In the chosen time intervals have alarm input will start alarm output 4 5 System Management Date Search Log Type All v 1 z 1 System Upgrade O
31. l vibration or attack Chapter one Products Introduce 1 Technical Parameter Compression standard H 264 baseline profile L3 1 Video ilnput Composite 1 0Vp p 750 BNCx4 BNCx8 BNCx16 BNCx24 BNCx32 Video output Composite 1 0Vp p 750 BNCx1 VGAx1 HDMIx 1 Resolution Preview D1 704x576 PAL 720x480 NTSC CIF 352x288 PAL 320x240 NTSC Recording D1 704x576 PAL 720x480 NTSC CIF 352x288 PAL 320x240 NTSC Frate rate Preview recording 4ch 100fps PAL 120fps NTSC 8ch 200fps PAL 240fps NTSC 16ch 400fps PAL 480fps NTSC 24ch 600fps PAL 720fps NTSC 32ch 600fps PAL 720fps NTSC Audio input 8dB 22k RCAx4 4ch Audio output 8dB 92dB RCAx1 Audio decode ADPCM Alarm input Input low level alarm user setting normal open or normal close Varies according to the model Alarm output 1ch output or 2ch output Varies according to the model Simplex duplex triplex triplex recording playback LAN transmission RJ45 10M 100M self adapting PTZ control Recording mode Manual recording timing recording motion detection recording and external alarm recording USB mouse control Hard disk drive 1or2or4x SATA 2TB or above Remote control unit RS485x1 USB2 0x2 Main board size 220mm x 112mm Power supply AC110 230V 1 2 Performance Real time monitoring Compression format Recording and playback function Turn by turn analog video output and VGA interface according to TVmonitor
32. nline After finishing installation as the following figure shows before using public IP and mobile phones need to open wifi before using LAN IP 2 lt port gt The mobile phone port set in DVR default parameter is 8888 3 lt uer ID gt The username permitted to login the DVR default username is admin 4 lt password gt The password of the user default password is empty 7 2 1 operation instructions 5 lt alias gt the record s name After installing click Asee icon to work After entering the above information identify and select play Log on the main menu interface as the following figure shows 128 0 254 115 Playing 64 ASee File Edit View Window Help Thu AnA add device modify Modify device Switch pictures on Imac platform click view gt scream mode on the top of the screen to switch pictures from 1 4 9 16 Channels lato 1 Aian as the following figure shows Dees lina View Window Help Full Screen A Screen More main menu interface picture switch After loading enter default main menu interface buttons instruction as show below First login preview interface is empty need to set parameters and add device after adding device can preview buttons instruction configuration modify or delete equipment information ect single picture Single picture shows video channel click add id pop up a message box as shown in the follong fig
33. nline Users Exception Handling Default p T carseacn Date Search Can search according to date Log Type Optional all operation log set diaries alarm log error log Note according to the left right arrow can move forward and content 33 34 3 Default Recording Setup Video Setup Channel Overlay Motion Detection mg Diar Setup Alarm Setup Log Search Online Users Exception Handling Restoring default can restore selected according to need The system restore to the default configuration state out can according to the menu options choose to restore the corresponding Settings Tip menu color language time date format video format IP address the user account etc will not be restored 4 Exception Handling System Upgrade capion Type Lem Buzzer p Log Search Online Users Default 35 Exception Type Choose abnormalities hard disk full hard disk errors network connection Buzzer When abnormality choose whether to allow the buzzer hints Chapter Five IE Preview 5 1 logging on interface To input the IP address Login server E After succeed in logining or logouting server exit dialog Net Search Login mode me 192 168 0 19 192 168 0 19 EE re od odd ie oe OES ETE i IP Address Port User Name Password IV Save Password Ate breede all channels when succeed in logining server W Internet From window 5 gt to start Pretermission I
34. nnel numbers as shown in the above image 7 Double click any channel then switch to the lt channel preview gt interface to preview channels it can support four channels previewing at the same time as shown in the below image Back Device Manage Add Sa DVR 4 8 Click the lt settings gt button Ey enter the lt Device Manage gt interface as shown in the above image The user can edit modify and delete device information by clicking the corresponding icon or slipping the item 1 Click the lt edit gt button gt enter lt parameter modifying gt interface as shown in the below image 58 Back Device Manage Add F DVRI4 2 Slide rightly the lt edit gt button to delete the information As shown in the above image 4 Video display mode There are two modes common mode and full screen mode Switch when the mobile phone lay down horizontally it will automatically display full screen common mode full screen mode 5 Channel switch function Select some channels in the Device list interface the program will automatically switch to the Preview Interface and open the corresponding channel preview in Preview Interface Program displays the default 1 4 channels when elected the channel lt Channel switch gt button in the lt preview interface gt the channels group will switch to 5 8 8 12 12 16 and circulation switch As shown in the below image 59 DVRI4 6 1 4 Instructions of
35. of PTZ Left control of PTZ The left direction control of PTZ 52 Right control of PTZ The right direction control of PTZ New Device The zoom in control of PTZ Zoom out The zoom out control of PTZ Delete All Records Focal length Amplify the focal length of PTZ a The corresponding functions of buttons in lt device edit gt interface show as follows Menu definition Function specification Focal length Lessen the focal length of PTZ Set to real time preview When the program connects with device play video Amplify the aperture of PTZ Lessen the aperture of PTZ Edit record 6 Exit the application program Delete Delete the selected record Click the button lt Exit gt and exit the program as the below image shows Edit Delete Delete All Records Delete all records Shutdown Shut down the program Setting Title 5008 Device List Sure to exit the application EEE ES DeviceList 6 1 3 Instructions of iPhone 7 Edit the lt Device List gt interface 1 Click the lt Device List gt and enter lt Device List gt interface as shown in the above image 6 1 3 1 Essential condition 2 Click the lt menu gt button and enter the lt device edit gt interface as the below image shows 1 Support the version iOS 3 0 or above and mobile phones includes iPhone iPod touch etc 2 Support DVR platform versions gt Hisilicon v1 0 1 8 and higher gt GRain v8 33 and higher 2 2
36. ol possess a standard Ethernet interface achieve the network remote monitoring mouse operation function In menu for same setting and to process shortcut copy operation 2 1 H 264 standalone 4CH 8CH 16CH 24CH 32CH DVR 2 1 1 Hard disk Installation For the first use please install the hard disk o I Remove the screws on both sides of shell o 2extracted from the next cover up 3connect hard disk and mother board AUDIO IN Ach or 8ch audio input o 4fix the screw of hard disk o Sclose cover o 6install the screws on both sides of shell V OUT 1ch video output 2 1 2 Rear panel A OUT ich audio output VGA monitor 4CH HDMI HDMI interface U NETWORK RJ45 A a T si ox i SB First USB for backup or upgrade system of DVR Second VIDEO IN USB for mouse 1234 C0 AB d ON OFF Power supply switcher STR DC 12V Power adaptor port ALARM NIRS485 S Sq ss ALARM IN IN1 IN4 alarm input port pt VIDEON 4ehvideoinput S O A OUT ps VGA VGAmonitor o O 6 mu HDMlinterfae Cd USB First USB for backup or upgrade system of DVR Second CHOI CHO CHOI CHO4 CHOS CHOG CHO CHOB CHOG CHIO CHI CHI2 CHI3 CHI4 CHIS5 CHI6 USB for mouse 2 ON OFF Power supply switcher er te 1234 00 48 V OUT A OUT CHO CHO2 CHOJI CHO4 ALARM OUT N1 alarm output port every channel connect GND OUT COM every two channel OUT COM port is for GND DC 12V Power adaptor port ALARM IN 1 2 3 4 alarm inp
37. or VGA monitor to live view in1 4 8 9 16 24 320r more video channel tomonitoring the recording streaming and the record file capacity in Every hours every channel to presentation the status of video channel recording dynamic detection video loss monitoring lock up You can view the system log in local DVR Video compression format H 264 Support 8ch video and audio signal video and audio maintaining stability in synchronous Multiplex to achieve real time recording to be independent at the same time to single channel playback research and backwards network monitoring network search download etc Multiple recording mode Manual normal alarm linkage dynamic detection recording etc turn by turn pre recording function Can playback the record file in DVR through network to achieve quick search the recording file and recording type multiple playback type SLOW Fast Forward Backwards step Forward Display the exact time of event occurred while recording file playback Storage function Backup function Network Operation function Internal 10r2 or 3SATA interface MAX 2TB hard disk drive the file of hard disk drive include cover mode circulation recording and none cyclical recording the storage data to use the proprietary format can not falsify the data make sure the data safety Through USB interface to backup for example USB drive and mobile hard disk drive etc The video file can
38. rd Close current window Exit from current control Return to last menu Exit from PTZ control under preview state ENTER OK Slow playback 1 2x 1 4x 1 8x and single frame play This button is used as enter and ok key in most circumstances Access exit from PTZ control under preview state Volume or number increase reduction Select item of the list FN Short cut Playback stop E Switching 1 4 8 9 16 24 32Preview re pan pan Play Pause o Pai Pause Pause Four way to move the focal point in main menu up and down to move in the normal ALARM Alarm reset window to control pan driver to move in the PTZ control windows ZOOM IN OUT Lens control Digital input Corresponding Fast playback 2x 4x and 8x 0 9 10 Channel is magnified in full playback screen under preview state REC To mode of recording CLEAR choosing 3 1 2 How to use mouse of DVR for right hand mouse To any function menu icon click the mouse left key into the menu To run the control point out operation Change again select frame or motion detection piece mode Click the assemble frame popping to pull down the list In the input frame can select digit character lowercase block letter left click mouse on the keyboard of character input that s say move back _ say Left key single click blank Shift say switch case 13 Right click mouse popping the shortcut menu as follows W Main Menu g
39. rd disk drive it will cause the mosaic Postscript Product parameter Table Compress standard Video in Video out Picture standard resolution ratio BNC 1 0Vp p 750 1TV BNC 1 0Vp p 75Q 1VGA 1HDMI PAL 704x576 NTSC 720x480 1024x768 800x 600 1280x1024 H 264 baseline profile L3 1 BNC 1 0Vp p 750 1TV BNC 1 0Vp p 75Q 1VGA 1HDMI PAL 704x576 NTSC 720x480 1024x768 800x 600 1280x1024 BNC 1 0Vp p 75Q TV BNC 1 0Vp p 75Q 1VGA 1HDMI PAL 704x576 NTSC 720x480 1024x768 800x 600 1280x1024 BNC 1 0Vp p 750 1TV BNC 1 0Vp p 75Q 1VGA 1HDMI PAL 704x576 NTSC 720x480 1024x768 800x 600 1280x1024 BNC 1 0Vp p 75Q 1TV BNC 1 OVp p 75Q 1VGA 1HDMI PAL 704x576 NTSC 720x480 1024x768 800x 600 1280x1024 Record encoded D1 HD1 CIF D1 HD1 CIF D1 HD1 CIF 70 Roll rate RCAx4 RCAx8 RCAx4 RCAx8 RCAx8 BNCx1 BNCx1 RCAx1 BNCx1 BNCx1 ADPCM ADPCM ADPCM Audio encoded rate Alarm Out Hd interface Network interface Mobil platform RS485 PTZ control PTZ control PTZ control PTZ control PTZ control Communication port USB interface PAL 1 25P S NTSC 1 30P S ADPCM Manual record motionrecord and externa alarm record Record Play Internet No RJ45 10M 100M PAL 1 25P S NTSC 1 30P S ADPCM Manual record motionrecord and externa alarm record Record Play
40. rding Schedule 23 Record ing Setup Sub Stream Channel Week Mon Channel 198 Overla vveg a Be Thu Fri Sat Channel Choose the need to install passage whole says setting all channels Each longitudinal row of every seven days a week said the 24 hours a day manipulated said mouse the left key click on the small square footage setting time to clean it has chosen right click drag video time 4 2 Camera When the system starts the camera will detect the format of video 1 PTZ Setup ER Channel Channel 01 v PTZ Protocol PTZ Address Video Setup Motion Bit rate 2400bps v Detection Data Bits SEQ Display Stop Bits Data Check Save Channel Choose regional channels yuntai Settings whole says setting all channels PTZ Protocol Yuntai equipment communication protocol 24 It contains these options Pelco D Pelco P LILIN MINKING STAR VIDO NEON DSCP HY N control RM110 SAMSUNG the default option is Pelco D Note yuntai parameter Settings every channel need after completion in Settings of gc1318 alone PTZ Address Yuntai equipment address digital range 0 to 255 Note here with the address must be consistent ball machine address we can t control the ball machine Bit rate Yuntai equipment baud rate 2 Video Setup PTZ Setup Video Mode PAL eem d Channel Channel 01 v Video Setup Reserved Section Setup y Detection wm Buzzer Alarm SEQ Display Vi
41. ring playback the Playback Tool will show the file playback speed channel timing playback speed etc information in the Playback control panel 2 Can t same time to select the Fast forward operation function in over 2 channel only progress in anyone channel 3 Can drag the Playback Speed toolbar by mouse 4 In this dialog you can select the video precise to the second JG WW Mon Tue Wed Thu Fri 1 8 15 KR EA frr 27 28 29 a EI 06 09 2012 12 00 00 AM Select Playback Time 2 0 0 AMES 11 59 59 PM pRB 3 8 How to control PTZ Normal Control x Zoom Preset Oo Focus Transfer lris Clear Zoom Lens in the current play far closer picture use the mouse wheel also can undertake variable times control Focus Slight adjusting the focal length Iris Aperture size adjustment Speed Through the slider adjust rotation stepinterval yuntai mainly used to control direction operation the step length of turning the faster yuntai Preset Adjust the camera Angle then direction and the corresponding input and clicking on set button preset dots to set the dots in the preset rastelli Input presets dots and click on Transfer button the camera will be transferred to the preset point corresponding position Click remove button this presets dianjiang be cleared Normal Control x Set H Preset Oo Dwell Time iN Add Preset Start Tour Delete Preset Lehm ClearTour
42. rmats Date Mode To choose time display modes include 24 hour system and 12 hours to make System Date The current system date System Time The current system time Daylight saving mode According to the requirement to choose Set Time Confirm modification system of time 2 HDD Management Disk Full Recycle File Time 6 Minutes Hard Disk Total Size User Management Alarm Setup Recording Bit rate 0 Recording Time 0 Output Formatting Schedule Disk Full When video disk full system how to deal with said system will be automatic coverage the earliest video files continue covering video stop video says system to stop the current video File Time Says automatic generation video files interval the set range 5 120 minutes Recording Bit rate Said the total rate of current coding Recording Time Said the storage devices systems installed in accordance with the current bitrate can store video of time Display the current hard disk attributes types hard disk usable capacity total capacity Click formatting all storage file will be lost Tip to format the hard disk before please stop system current all those videos 3 User Management 31 Permission Type System Privileges v Time EEE SEEREN HDD Recording Setup Management Sub Stream C Channel Overlay Recording Schedule m PTZ Setup Alarm Setup LT e SSS Output Add User Delete User Schedule E Edit User Edit Password ave SI
43. system Notes 43 44 Dialer 2 Install offline Contacts Browse All apps SH HiMarket 3D Cat Adobe Reader mr E ASTRO Calculator Calendar Call History p Oo S a Camcorder Camera Canimals Car Panel Diary d amp 8 Clock Connected Dock Mode Downloads Google Hs VERE TVK Copy the Asee apk installation package to Android phone through cable In the specified directory find out the corresponding apk click the application installation If there is not installed apk installer in the mobilke phone the user needs to download an apk installation software so that it can identify the apk package and there will be program icons after finishing installing As the above image shows 3 Click the program the first screen after running is shown in the below image The functions of buttons show as follows Table 1 1 Function keys Function specification D Previous group Next group Select channel ef 4 PTZ control v gt Focal length 4 If it is first running or need to change the parameters please click the lt settings gt button When the program connects with device play video Capture the current screen the default save path the default pictures directory of mobile Set some information of the device such as IP address dynamic domain name port username password and device alias information Some device information of the software It can show the previo
44. t If POWER pilot lamp to offer RED press the POWER key DVR begins to start The video output mode of DVR s the default setting is multi picture channel mode after starting the DVR if the time of start the DVR is in the Timing Recording Setting the DVR will automatically to start the Timing Recording function the corresponding channel s recording pilot lamp will be light the DVR is normal operation Buton Description Buton Description 14 3 3 Shutdown PTZ control There are two safety mode for Shutdown Wizard language Alarm control Multi channel Display setup D Recording Control Enter Exit select Power Down Logout Power Down Reboot Cancel Playback Back up If before starting the system not to install hard disk into the system will tip system didn t detect any hard disk Abnormal shutdown connection Through the rear panel to shutdown Note g p In this dialog you can select language and quickly set various of parameters During the DVR running directly to turn off the power through the rear panel power switch please avoid as much as possible to do it Specially while the DVR recording Directly to pull up the power cable of DVR While the DVR running directly to pull up the power cable of DVR please avoid as much as possible to do it specially while the DVR recording Caution In some area the power supply is irregularity it will cause the DVR working not normal oper
45. t Wizard 25 Multi Channel Recording Control Playback A Backup Q PTZ Control Right click mouse s Alarm Control Display Setup Hide Toolbar Through the menu can be switching preview screen window mode start replays PTZ control Four pictures playback mode the point of the right mouse button Can in a single picture four pictures eight pictures 8 road playback 16 screen 16 road playback twenty four picturethirty two picture broadcast control switch view show or hide broadcast control bar To run the ActiveX Control ActiveX special operation For example double click the certain item of record listed file then the system will playback the segment record video Double click left button Depress the left key and dragging the mouse banding select Motion detection area depress right key of mouse and Dragging cancel the banding select area Dragging the mouse Dragging playback ProgressBar back and forth to dolly moves to achieve the playback position adjustment Dragging the audio and video regulation parameter bar dolly moves to achieve the parameter adjustment 3 2 Powering On Boot strap If POWER pilot lamp off please follow the operation step by step First step if the power does not plug into please plug into the power then the DVR begin to start by now if the DVR still inactive to enter the next step Second step turn on the power supply of the DVR atthe back panel DVR begins to star
46. there is error device information above click to modify or click 9 10 11 12 13 14 15 16 Channels Info Device list add the device again Note Asee on Imac platform can only add one device and there is no PTZ control function 68 Chapter Eight FAQ Frequently Asked Questions 01 Why the DVR did not run after connect the power supply fr Please check the power switch turn on or off at the rear panel of DVR fr Q Please check if the turn on DVR operation correct or not fr GO you select the adaptor 12V 5A or above 8ch 5A 16ch 220V 200W e 02 Still stop over on the boot strap frame Physical damaged in hard disk drive fr Boot manager abnormal e 03 Why does appear the boot running too slow fr There are too much capacity data in hard disk drive the system will automatic search the data when the system boot up caused the boot running slow fr The hard disk drive error will cause the system research the data repeatedly caused the boot running slow e 04 Why does the system reboot repeatedly Check the hard disk drive if there is not the FAT32 formatted in it or the problem in it and caused the DVR reboot fr Q Please check the power supply of DVR if you installed a lot of hard disk drive it may be reboot repeatedly underpower fr Please pull up the network cable then to check the DVR can work normally or not being the
47. to choose don t use allow access refused to visit Starting IP Display IP address started section Ending IP Display IP address end segments Add On the basis of the need for added Delete According to the need to delete 4 4 System Setup 1 Time Remote Controler Device Name ave SSL Protocol Sending E mail in use safety network connection Test Email Send an email to the recipient mailbox test Email Address The recipient s email address Users can input two different email address Send Email The sender email address SMTP Server Send mailbox mail server Email Account The sender email address the corresponding account Email Password The sender email address of the corresponding email password According to the customer request can be checked input alarm and video loss sending emails Two can 29 Management Date Mode User Management Alarm Setup Output Schedule MM DD YY v Time Mode 12 Hours System Date 13 System Time DST NTP Setup Set Time System Language Used in a remote remote device control more hard disk video recorder occasions only in 30 remote controls address and hard disk video recorder Numbers identical to remote operation Device Number According to the requirement to select the time zones has twenty six time zone for user Settings Time Zone Select the format the date is displayed in including date sun and moon June 21 years in three fo
48. ure 4 pictures Apictures show video channels Name i i f i Address disconnect disconnect single picture of connection Sen ort User az E E disconnect Password disconnect all pictures of connection ote Capture Capture the current image the default save path the default pictures directory of mobile Cancel OK full screen Picture full screen add device The current message box shows the need to enter five information device name IP address port user ID and password 65 66 Device name the name of monitor device help you distinguish between multiple devices IP address The public IP address or dynamic domain name of DVR here the address must be internet address port The mobile phone port set in DVR default parameter is 8888 User name default username usually to be admin can be set according to the DVR Password admin user s default password is empty can be set according to the DVR Back Name 611 Address 128 0 254 101 Port 8888 User admin Password Note Cancel OK add device after inputting above information click ok enter main menu interface click a picture after appearing green 1 frame as shown window 1 in picture below click a channel on right channel column such as channel 1 connect play as shown in the following figure 67 AOA ASee e mees LA zez eee les connection play interface If
49. us channels group It can show the next channels group Choose one video channel of the device And cooperate with next group can switch the 8 or 16 channels PTZ direction control including up down left and right Zoom in out control of PTZ Focal length adjustment of PTZ Aperture control of PTZ Be gleef and enter the lt Device List gt page as shown in the below image 46 DVR Title Ne Server Part User Name Password Max Channel 16 Ok Cancel Add In lt device list gt interface click lt Add gt button and enter lt settings gt interface as shown in the above image Notes gt lt DVR Title gt It is convenient to identify among multiple devices gt lt Server gt The public IP address dynamic domain name or LAN IP of DVR The port should be mapping before using public IP and mobile phones need to open wifi before using LAN IP p gt lt Port gt The mobile port set in DVR default parameter is 8888 gt lt User Name gt The username permitted to login the DVR default username is admin gt lt Password gt The password of the user default password is empty gt Max Channel gt The actual channel numbers of DVR 5 After finishing click lt OK gt and enter the Device List Device List page As shown in the below image 47 gt MY
50. ut port RS 485 A B CHO CHO2 CHO CHO4 AUDIO IN ALARM pg ALARM OUT N1 alarm output port every channel connect GND OUT COM ARA every two channel OUT COM port is for GND e a e s e a S S l o dro gc ALARM NI 485 CHO CHO2 CHOI CHO4 CNDS CHOG CHO CHOR A ga A ON OFF wt 1234 00 A8 DC 129 ALARN NI RS485 item interface Description HDMI HDMI interface Interface Description NETWORK RJ45 for internet VIDEO IN 8ch video input USB MOUSE First USB for backup or upgrade system of DVR Second 7 8 OFF USB for mouse ON OFF Power supply switcher DC 12V Power adaptor port 1234 CO AB ALARM IN 4CH alarm input port DNS SAS AR SDR Al PAA NALA LVK AKA RS 485 A B i OFF ON AUDIO IN Hou NETWORK USB MOUSE VGA ALARM OUT N1 N far alarm output port every channel connect C and O port is for GND OFF ON NETWORK RJ45 for internet USB MOUSE First USB for backup or upgrade system of DVR Second USB for mouse i R is HI NETWORK USB MOUSE si our say OR ON OFF Power supply switcher i l DC 12V Power adaptor port USB MOUSE First USB for backup or upgrade system of DVR Second USB for mouse ON OFF Power supply switcher DC 12V Power adaptor port ALARM IN 16CH alarm input port RS 485 A B R5485 S A B ALARM OUT N1 N r alarm output port every channel connect C and O gt port is for GND
Download Pdf Manuals
Related Search