BlueMAX Owner`s Manual
Contents
1. a SIDECHAIN INSERT Sidechain insert allows the Blue Max to be used for special processing applications such as de essing and ducking 4dBu OR 10dBV OPERATION Internal operating levels are switchable from 4dBu to 10db V for system matching requirements a INTERNAL POWER SUPPLY No Wall Wart 2 CONTROLS amp CONNECTIONS 2 1 FRONT PANEL BASIC LAYOUT The front panel on the Blue Max is divided into three sections These are 1 Presets Fifteen detented preset positions and Manual select The Presets for the Blue Max are controlled by this sixteen position rotary encoder As the encoder is rotated parameters are digitally switched simultaneously controlling attack release ratio and threshold 2 Controls amp Meters Input The Input control adjusts the gain on the input amplifiers for both channels Amplification gain varies widely from 20dB to 40dB The large range is necessary to amplify instruments such as guitar Thus the input stage to the Blue Max is actually a pre amp Note The input control is always active even in manual mode Ratio Ratio sets the compression slope This is defined as the output level versus the input level For example if you have the ratio set to 2 1 any signal levels above the threshold note threshold is a preset parameter in the Blue Max will be compressed at a compression ration of 2 1 This simply means that for every 1dB of level increase into the compressor2. Users Manual V I 2 0 BLUEMax SMART COMPRESSOR USERS MANUAL Version 2 0 1997 PreSonus Audio Electronics Incorporated All rights reserved Updated by J Luck 2004 WARRANTY PreSonus Limited Warranty PreSonus Audio Electronics Inc warrants this product to be free of defects in material and workmanship for a period of one year from the date of original retail purchase This warranty is enforceable only by the original retail purchaser To be protected by this warranty the purchaser must complete and return the enclosed warranty card within 14 days of purchase During the warranty period PreSonus shall at its sole and absolute option either repair or replace free of charge any product that proves to be defective on inspection by PreSonus or its authorized service representative To obtain warranty service the purchaser must first call or write PreSonus at the address and telephone number printed below to obtain a Return Authorization Number and instructions of where to return the unit for service All inquiries must be accompanied by a description of the problem All authorized returns must be sent to the PreSonus repair facility postage prepaid insured and properly packaged PreSonus reserves the right to update any unit returned for repair PreSonus reserves the right to change or improve the design of the product at any time without prior notice This warranty does not cover claims for damage due to abuse neglect altera
3. Introduction 1 2 Features 2 Controls amp Connections 2 1 Front Panel Basic Layout 2 2 Back Panel Basic Layout 2 3 Presets 3 Basic Setup amp Operation 3 1 Quick Start 3 2 Basic Connections 3 3 Basic Operating Procedures 4 Technical 4 1 Specifications 1 OVERVIEW A Word about Compression Punch apparent loudness presence just three of many terms used to describe the effects of compression limiting Compression and limiting are forms of dynamic range volume control Audio signals have very wide peak to average signal level ratios Sometimes referred to as dynamic range which is the difference between the loudest level and the softest level The peak signal can cause overload in the audio recording or reproduction chain resulting in signal distortion A compressor limiter is a type of amplifier in which gain is dependent on the signal level passing through it You can set the maximum level a compressor limiter allows to pass through thereby causing automatic gain reduction above some predetermined signal level or threshold Compression refers basically to the ability to reduce the output level of an audio signal by a fixed ratio relative to the input It is useful for lowering the dynamic range of an instrument or vocal making it easier to record without distorting the recorder It also assists in the mixing process by reducing the amount of level changes needed for a particular instrument Take for example a
4. gives a fat contour to even out the sound from overhead drum mics Low end is increased and the overall sound is more present and less ambient More boom less room 13 7dB 1 3 1 27mS 128mS Fretted 1 ELECTRIC BASS A fast attack and slow release to tighten up the electric bass and give you control for more consistent level 4 4dB 2 6 1 45 7mS 189mS 2 ACOUSTIC GUITAR This setting accentuates the attack of the acoustic guitar and helps maintain an even signal level keeping the acoustic guitar from disappearing in the track 6 3dB 3 4 1 188mS 400mS 3 ELECTRIC GUITAR A setting for crunch electric rhythm guitar A slow attack helps get the electric rhythm guitar up close and personal and gives punch to your crunch 0 1dB 2 4 1 26mS 194mS Keyboards 1 PIANO A special setting for an even level Designed to help even up the top and bottom of an acoustic piano Helps the left hand be heard with the right hand 10 8dB 1 9 1 108mS 112mS 2 SYNTH Fast attack and release for synthesizer horn stabs and for bass lines played on a synthesizer 11 9dB 1 8 1 0 002mS 85mS 3 ORCHESTRAL Use this setting for string pads and other types of synthesized orchestra parts It will decrease the overall dynamic range for easier placement in the mix 3 3dB 2 5 1 1 8mS 50mS Stereo 1 STEREO LIMITER Just as the name implies A hard limiter setting brick wall ideal for controlling
5. other compressors in the fact that there is no threshold control This offers the unique ability to immediately hear the sometimes subtle differences between presets which each have unique threshold settings In setting the compression amount always begin with the Input control all the way counter clockwise 20dB and slowly increase the input until the Gain Reduction meters begin to register the compression activity The more you crank up the Input the more compression your signal will experience Always pay close attention to the best judge of your sound your ear You should also frequently remove the compression from the signal using the Process button to listen to the changes in your sound In modem recording practice it is customary to adjust the Output control such that the Input and Output level are of equal amounts according to the Input Output meter This gives you an equal level output so that you can switch processing in and out to compare difference Mono Operation Your Blue Max was designed with a high gain mono input to act as a preamp for instruments such as guitar and bass Of course you can also connect your keyboards etc in this mode Note It is very important not to rely on the high input gain of the Blue Max to boost the level of a signal too low to record or amplify other than that of instruments such as guitar and bass Be sure that you are sending the Blue Max at least a moderate level before setting the compression I
6. the output will only increase 1 2dB thus producing a compression gain reduction of 0 5dB As you increase the ratio the compressor gradually becomes a limiter A limiter is defined as a processor that imits the level of a signal to the compression threshold For example if you have the ratio set to 20 1 input set at OdB the output of the Blue Max will be limited to the internal threshold of the compressor which is set to 10dB in manual mode Note The ratio control is only active in manual mode Attack and Release Attack sets the speed at which the compressor acts on the input signal A slow attack time fully clockwise allows the beginning envelope of a signal commonly referred to as the initial transient to pass through the compressor uncompressed whereas a fast attack time fully counter clockwise immediately subjects the signal to the ratio and threshold settings of the compressor Release sets the length of time the compressor takes to return the gain reduction back to zero no gain reduction Very short release times can produce a very choppy or jittery sound especially in low frequency instruments such as a bass guitar Very long release times can result in an over compressed sound sometimes referred to as squashing the sound All ranges of release can be useful at different times however and you should experiment to become familiar with the different sound possibilities Note The Attack and Release co
7. 20dB to 20dB Compressor Metering Input Output Level Gain Reduction Sidechain Output Impedance 51 Ohms Sidechain Input Impedance 10kOhms Internal Operating Level 4dBu 0dB Input Range 4dBu or 10dBV Switchable Input Connectors Ya Tip Sleeve Output Connectors Ya Tip Sleeve Sidechain Connector Ya Tip Ring Sleeve Power Supply Internal Linear Supply Power Requirements 120V AC or 240V AC 10W Weight 8lbs Size 8 X1 72 X5 13
8. gain setting remains active 2 2 BACK PANEL LAYOUT Input The input jack accepts unbalanced tip sleeve connectors The input can handle up to 24dBu unbalanced levels The left input is a dedicated mono input Output The output jack accepts unbalanced tip sleeve connectors The output will deliver up to 24dBu in signal level unbalanced The left output is a dedicated mono output Sidechain The sidechain jack on each channel interrupts the signal that the compressor is using to determine the amount of gain reduction to apply When no connector is inserted into this jack the input signal goes directly to the compressors control circuitry When a connector is inserted into this jack the signal path is broken If you have inserted a tip ring sleeve connector the input signal is sent back out of the Blue Max via the tip of the connector This signal can then be processed by an equalizer for example to reduce sibilance de essing ina vocal track The signal is then returned to the unit via the sleeve of the connector PreSonus Sonus ov MORURASTRBERITE USBics BLUE Mex Smart Compressor OUTPUT aN pe EL a y IAS ND A A N f f 120 240 VAC So 6oH2 10w POWER Tip senD ILEFT IMONO RIGHT SIDECHAIN The signal sent to the sleeve could be that of a narrator or vocalist In this application the audio that you are passing through the compressor will automatically duck when the narrator speaks or vocal
9. hould now have a very natural sounding compressed signal Of course you should experiment with the settings to suit your taste 3 2 BASIC CONNECTIONS Inserting into your mixers insert point Presonus wy MAMUPAGTUBER INTE USA BLUEMAK Smart Compressor m OUTPUT O INPUT a P j A O N D j 120 240 vac osoz 10W POWER tip seno LEFI ONO RIGHT LEF ONO RIGHT Mixing Board Insert Point 7 n Note If you don t get any signal flow at first try swapping the input and output connections Connecting your instrument mixer or tape machine PreSONUS Mn MASSAS SENE si BLUEMax Smart Compressor E 120 240 VAC 50 60Hz 10w POWER zZ T am O Lu a u To Mixing Board Amplifier or Tape Machine From Instrument or Mixing Board aa Connecting for de essing or spectral processing Auto terora BY PRESONUS AUDIO ELECTRONICS L_ 120 240 VAC 50 60Hz 10w POWER SIDECHAIN To Equalizer Input i From Equalizer Output l To Mixer Insert Point 11 Connecting for stereo operation BLUEM x Smart Compressor zZ y S O gA w 120 240 VAC 50 60Hz ow POWER TIP SEND To Stereo Input Left a To Stereo Input Right a lt From Stereo Output Left a From Stereo Output Right amp C 3 3 BASIC OPERATING PROCEDURES Setting Compression Amount Your Blue Max was designed with a fixed threshold mode of operation This differs from
10. ist sings 4 10 Switch This switch adjusts the internal operating level of your Blue Max when it is connected to line level OdB 10dBV gear With the switch in the 10 position the signal is raised internally so that it is processed at the lower noise floor of your Blue Max s internal circuitry The signal level is lowered on the way out to match up with your line level gear s input When the switch is in the 4 position the signal is not changed since this matches the internal operating level of your Blue Max This function may also be useful in creating special effects with the compressor and gate of the channel by overcompressing 2 3 PRESETS Vocal 1 SOFT Easy compression A low ratio setting for ballads allowing a wider dynamic range Good for live use This setting lets the vocal sit in the track 8 2dB 1 8 1 0 002mS 38mS 2 MEDIUM More limiting than preset 1 for a narrower dynamic range It moves the vocal more up front in the mix 3 3dB 2 8 1 0 002mS 38mS 3 SCREAMER For loud vocals Fairly hard compression for a vocalist who is on and off the microphone a lot It puts the voice in your face 1 1dB 3 8 1 0 002mS 38mS Percussion 1 SNARE JKICK Allows the first transient through and compresses the rest of the signal giving a hard snap up front with a longer release 2 1dB 3 5 1 78mS 300mS 2 L R Stereo OVERHEAD A low ratio and threshold
11. level to the 2 track mixdown deck or stereo output 5 5dB 7 1 1 0 001mS 98mS 2 CONTOUR A contoured setting for use on the stereo output to fatten up the mix 13 4dB 1 2 1 0 002mS 182mS Effects 1 SQUEEZE Dynamic compression for solo work especially electric guitar It gives you that glassy tele strat sound A true classic 4 6dB 2 4 1 7 2mS 93mS 2 PUMP Make the Blue Max pump up the prime A setting for making the compressor pump in a desirable way This effect is good for snare drum to increase the length of the transient by bringing the signal up after the initial spike Very contemporary 0dB 1 9 1 imS 0 001mS 3 BASIC SETUP amp OPERATION 3 1 wo N NO Of 8 QUICK START Connect your Blue Max using one of the diagrams below Select either 4 or 10 operating level Reminder 4 is for pro levels such as consoles 10 is for consumer levels or instruments Select your preset Refer to the preset descriptions above Remember that the Ratio Attack and Release knobs are only active in Manual mode Push the Process button in Turn the Input knob all the way to 20 counter clockwise Set the Output knob on 0 Slowly turn the Input knob up clockwise until the Gain Reduction meters begin to move Continue to rotate the Input knob until the Gain Reduction meters read between 5 and 7 Adjust the Output knob to the desired output level You s
12. n this manner you avoid unnecessary input amplifier noise 12 Stereo Operation Your Blue Max is operating in a linked stereo mode at all times In this mode both signals are used to create the gain reduction amount This insures proper stereo imaging in stereo compression applications The stereo presets were optimized for two basic settings however all of the presets will work in stereo mode Manual Mode With the Preset selector set in the Manual position you have complete control over the compression settings In this mode the threshold is fixed to 10dB Therefore you should follow the same setup procedure as in the preset operating modes Remember that if the Ratio control is set to 1 1 fully counter clockwise the compressor is basically off A good place to start is with a 2 1 compression setting and Attack and Release in the 12 o clock positions You may also want to start with one of the preset settings as described above 4 TECHNICAL SPECIFICATIONS Number of Channels 2 Dynamic Range gt 115dB Signal to Noise Ratio gt 95dB Headroom 24dBu Frequency Response 10Hz to 50kKHz Crosstalk gt 82db 10kHz Compression Ratio 1 1 to 20 1 Compressor Attack Time 0 0ImS to 100mS Compressor Release Time 10mS to 500mS Input Impedance Left Mono 100kOhms Input Impedance Right 10kOhms Output Impedance 51 Ohms THD Noise lt 0 03 Input Gain 20dB to 40dB Output Gain
13. ntrols are only active in Manual mode Input Output Meter The Input Output meter shows the signal level being processed by the Blue Max Input refers to the signal level being processed by the Blue Max before processing Output refers to the signal level after processing OdB on the meter is referenced to the 4 10 switch on the rear of the unit In 4 mode 0dB 4dBu In 10 mode OdB I0dBV Gain Reduction Meter The Gain Reduction meter indicates the amount of gain being reduced by the compressor in dB 3 Output amp Pushbuttons Output Level Control The Output control is used to set the desired output of the Blue Max It is sometimes referred to as gain makeup control This term is derived from the fact that as the compressor lowers the output level during gain reduction the overall signal level is lowered requiring the user to makeup the gain thereby restoring the original signal level Input Output Meter Select This button selects the function of the Input Output meter Pushed in the meter gives you the level of the input signal Pushed out the meter gives you the level of the signal after compression the output level Process In Out The Process button is similar to a bypass button except that the signal is still effected by the Input of the Blue Max Pushed in the Blue Max is processing the signal compressing Pushed out the Blue Max is no longer compressing the signal however the input
14. tion or attempted repair by unauthorized personnel and is limited to failures arising during normal use that are due to defects in material or workmanship in the product Any implied warranties including implied warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this limited warranty Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you In no event will PreSonus be liable for incidental consequential or other damages resulting from the breach of any express or implied warranty including among other things damage to property damage based on inconvenience or on loss of use of the product and to the extent permitted by law damages for personal injury Some states do not allow the exclusion of limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary form state to state This warranty only applies to products sold and used in the United States of America For warranty information in all other countries please refer to your local distributor PreSonus Audio Electronics Inc 501 Government St Baton Rouge LA 70802 504 344 7887 1997 PreSonus Audio Electronics Incorporated All rights reserved BLUEM ax TABLE OF CONTENTS 1 Overview A Word about Compression 1 1
15. ut having to crank the level way up A vocal performance usually has a wide dynamic range Transients the very loudest portion of the signal can be far outside the average level of the vocal signal It is extremely difficult to ride the level with a console fader A compressor limiter automatically controls gain without altering the subtleties of the performance A solo guitar can seem to be masked by the rhythm guitars Compression can make your lead soar above the track without shoving the fader through the roof Bass guitar can be difficult to record A consistent level with good attack can be achieved with proper compression Your bass doesn t have to be washed out in the low end of the mix Let the compressor limiter give your bass the punch it needs to drive the bottom of the track 1 1 INTRODUCTION Thank you for purchasing the PreSonus Blue Max smart compressor limiter with presets Your Blue Max was designed with you the end user in mind As far as we know it is the only compressor in the world with built in compression presets The presets were created not only to assist in setting up the compressor but to offer you the experience of professional engineers in using compression If this is your first compressor you will instantly gain valuable insight into what can be a confusing experience The experienced user will gain a few tricks of the trade usually kept in the arsenal of professional engineers This dynamics processor
16. vocalist who moves around in front of the microphone while performing thus making the output level vary up and down unnaturally A compressor can be applied to the signal to help correct this recording problem by reducing the louder passages enough to be compatible with the overall performance How severely the compressor reduces the signal is determined by the compression ratio and compression threshold A ratio of 2 1 or less is considered mild compression reducing the output by two for signals greater than the compression threshold Ratios above 10 1 are considered hard limiting Limiting refers to the point at which the signal is restrained from going any louder at the output The level of input signal at which the output is reduced is determined by the compression threshold As the compression threshold is lowered more and more of the input signal is compressed assuming a nominal input signal level Care must be taken not to over compress a signal Too much compression destroys the acoustical dynamic response of a performance Over compression however is used by some engineers as an effect and with killer results Compressor limiters are commonly used for many audio applications A kick drum can get lost in a wall of electric guitars No matter how much level is increased the kick drum stays lost in the mud Add a touch of compression and tighten up that kick drum sound allowing it to punch through witho
17. was built with state of the art components to deliver crystal clear compression for an infinite period of time We believe the Blue Max to be an exceptional sounding unit at an exceptional price We hope you agree Feel free to contact us at 1 800 750 0323 anytime for any reason We value your comments and suggestions Please pay close attention to how you connect your Blue Max to your system Improper grounding is the most common cause of noise problems in both live and studio applications We suggest you look at the connection diagrams which are part of this manual to insure optimum operation 1 2 FEATURES The following is a summary of the features of the Blue Max a PRESETS There are 15 studio proven settings for voice percussion fretted instruments keyboards stereo processing and effects a VARIABLE INPUT CONTROL In addition to normal stereo inputs the input control allows low signal levels such as direct output of electric guitars and basses to be increased to optimum levels a MANUAL MODE Full operator control of ratio attack and release is offered in manual mode a STEREO INPUTS OUTPUTS inch unbalanced stereo inputs left side mono and inch unbalanced stereo outputs left side mono for stereo recording and mix down use a FULL METERING Full metering for input and output levels are available as well as separate meters for gain reduction a VARIABLE OUTPUT Output control allows gain changes from 20dB to 20dB
Download Pdf Manuals
Related Search