Conductor
Contents
1. Power Input Port Printer Control Port Control Port SCSI Port Figure 3 Rear Panel of Conductor Please note that the SCSI port is not installed on your Conductor Instead a metal blank off plate has been put in its place The Control Port is installed but not used Both of these ports are for a future upgrade to a fully automatic optical disc duplication and printing system called Composer An upgrade to a Composer is accomplished by adding Windows based duplication software and a CD R or DVD R drive Contact your reseller or the factory for information on how to accomplish this upgrade Your printer autoloader configuration will use only the Printer Control Port and the Power Input Port E System Requirements Before getting started it is important for you to verify that the PC you plan to use with Conductor meets these minimum system requirements e Pentium II III or Celeron Processor 233 MHz or higher e 32MB RAM e Windows 95 98 NT 2000 operating system e Free hard drive space of at least 2MB SECTION 2 HARDWARE AND CABLE SET UP A Connecting the Parts and Interface Cables Follow these steps to integrate your autoloader and printer 1 In the Conductor shipping box you will find the Input and Output Bins Place the Bins in their correct places as shown in Figure 1 Depending upon which printer you are using you ll see that the locations for the Bins changes Upon power up Conductor will automatical2. IPUR AA lara 8 9 Printer Driver SOfEWATE coincido td dd Edd da 13 Printers Inscripta Thermal CD Printer od 6 7 9 10 16 signature Mir O tient rain 6 12 16 Signature Mia tata 6 7 9 11 12 16 Resetting the RODOLCS ai 15 Specification di tii 16 Stands RAN a a a o 9 10 System Requirements 2 NAS AD EA a AAA A A AA EA AA 8 18 Tech SUP DOME A SN A NM AR AN ANR M TE NEN RE no 15 Tray Support Brack Ra dent dr ben den ne O ne nr ue 10 UNPACKING atinado td 6 Printed in the United States of America P N 082100 510148
3. graphics editing program called SureThing First Edition 3 In the printer driver software for the printer you re using found under Start Settings Printers check under Properties Media that the Manual Load is checked and the Manual Unload is unchecked This is VERY important if these settings are not correct your autoloader will not autoload 4 Print a job to the printer as you normally would requesting the number of copies you desire That s it You should now be successfully printing and transporting up to 50 discs per batch automatically 14 SECTION 3 INTERPRETING THE LED STATUS LIGHTS The LED Status Lights located on Conductor s front panel can tell you a lot about what is happening at any given moment with the operation of the autoloader To accurately interpret what is meant when the lights are on off or flashing refer to the following chart A Power LED Status Off On Solid Flashing B Pause LED Status Off On Solid Flashing Condition No Power Plug in Power Adapter Power is ON This is Conductor s normal waiting mode Power is ON but an error condition exists a Didn t pick up a disc b Dropped a disc c Discs out d Robotic arm stalled probably hit something while moving Press any button on Control Panel to re try Condition Normal waiting mode Conductor is paused Conductor is busy i e motors are running printer is printing etc 15 SECTION 4 MAINTE
4. NANCE AND TROUBLESHOOTI NG Conductor is designed to operate for extended periods of time with very little attention In fact no regular maintenance is recommended other than cleaning the outside case IMPORTANT Do NOT attempt to oil or grease the Duplicator s Robotic Arm shaft or other components You will likely cause more harm than good Any moving parts are designed to be run for the life of the machine with no additional lubrication required A Cleaning The Case Use a clean white rag with a small amount of water or isopropyl alcohol to clean the Duplicator and printer s outside cases and CD trays Stronger cleaning solutions are NOT recommended because they may damage the paint and plastic materials from which the parts are manufactured Always disconnect your Conductor and printer power cords before cleaning Resume operation only after the surfaces are completely dry B Resetting the Robotics If you find yourself in a situation where the robotics are not responding properly you may need to do a system reset A typical cause may be when you stop a job out of sequence To do so press the Pause and Pick buttons at the same time C Technical Support If you have difficulties in operating your Conductor the set up and testing procedures in this manual should in most cases solve the problem If you still have difficulty contact the technical support number listed on the insert included in the supply pack that came with your pro
5. Operator s Manual onduchr PRINTER AUTOLOADER For Use With the Signature 111 CD Color Printer or Inscripta Thermal CD Printer TECHNOLOGY INC Two Carlson Parkway North e Plymouth MN 55447 4446 U S A Phone 1 800 797 2772 e 763 475 6676 e FAX 763 475 6677 Internet www primeratechnology com 2000 All rights reserved Notices The information in this document is subject to change without notice NO WARRANTY OF ANY KIND IS MADE WITH REGARD TO THIS MATERIAL INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE No liability is assumed for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated into another language without prior written consent Trademark Acknowledgments Windows is a registered trademark of Microsoft Corporation All other trademarks are the property of their respective owners Printing History Edition 1 0 082100 FCC Compliance Statement This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that
6. duct 16 SECTION 5 TECHNICAL SPECI FI CATIONS Model Robotics Minimum System Disc Capacity Operating Systems Power Requirement Weight Dimensions Certifications Warranty Conductor Printer Autoloader Controlled by Primera Technology Signature Signature II or Signature 111 CD Color Printers or Inscripta Thermal CD Printer Pentium 11 11 or Celeron Processor or equivalent at 233 MHz or higher 32MB RAM one free ECP parallel printer port 2MB available hard drive space 50 disc input 50 disc output Windows 95 98 NT and Windows 2000 100 240 VAC 50 60 Hz 60 watts 8 9 lbs 4 04 kg 16 625 W x 10 H x 10 125 D 422mmW x 254mmH x 257mmD Emissions FCC Class B CE Safety TUV GS cTUVus CE One year return to depot 17 INDEX Bins PUE o a e el ode 7 9 12 13 DUI A r iS er id 7 9 12 13 Buttons ES 13 14 15 PICK num A A 12 13 15 A E E E T E E A E 12 Cables 6 Pin MINDIN aria NE De AE 6 9 11 Connections Rear Panel nasal latina ita 8 o 7 Hardware TEStiNg ren teen seine en ententes tiges ner e tag de den 12 13 kd ntifying the Parts oe a ieee ied nahn Aaah ih iach c nn it 6 LED Status LIgNES coisa A A E ta Dols rcs Oe AS 14 Locating Holes PM bonne Rens 10 LOGAEOM it A A A tr aia un ed ores 6 MAINTENANCE isaac dirt at iain tte a site tien tuent 15 Parallel Interface CADIRE Ra A an AR dinate Re RAA Rte 11 ECM Oda than es see 11 Ports Printer Control aa 8 9 Power
7. ed the Class B limits for radio noise for digital apparatus set out on the Radio Interference Regulations of the Canadian Department of Communications Le present appareil numerique n emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la class B prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada CAUTI ON TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THE UNIT TO RAIN OR MOI STURE TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE EXTERIOR PANELS NO USER SERVI CEABLE PARTS INSIDE REFER SERVI Cl NG TO QUALI FI ED SERVI CE PERSONNEL OPERATE THE UNIT WITH ONLY THE PROPER ELECTRI CAL SPECI FI CATIONS AS LABELED ON THE PRINTER AND AC ADAPTER Table of Contents SECTION 1 GETTING STARTED A IN FOAUCTIONL sr RSR RC RE TRE SR N E et eendans 6 B Choosing a Good Location sn tieinelscs oo 6 C Unpacking and Inspection iii 6 D ldentifying the Pain ia tala da cidad 6 E System Requirements ias 8 SECTION 2 HARDWARE AND CABLE SET UP A Connecting the Parts and Interface Cables 9 B Hardware AA 12 C Printing Your First JOD a mn ae me rh ts 13 SECTION 3 INTERPRETING THE LED STATUS LIGHTS A POW Gr LED ie ant a ud Fatale et edad buen ng bu ans tete tt 14 B Pause LED O 14 SECTION 4 MAINTENANCE AND TROUBLESHOOTING A Cleaning the A wiviee titan iteniasesradietn SUNATI NETA 15 B Resetting the RODO
8. front panel The Robotic Arm will swing over to and above the Input Bin Press the Pick Button The Robotic Arm will pick up a CD 4 Press the Sequence Button again The Robotic Arm will swing in front of the printer 5 Open the printer s tray On Signature III this is the button middle button on top of the unit On Inscripta this is the button at the bottom right side of the unit Figure 13 Tray Open Button on Signature 111 6 Press the Pick Button The CD will drop into the printer tray If it does not drop perfectly into place you will need to adjust the printer stand s Mounting Plate This is accomplished by loosening the three Phillips head adjusting screws and moving the printer slightly in one direction or another until the disc is dropped perfectly into the printer s tray You can repeatedly press the Pick button to test your alignment Or press and hold the Pick button for 5 seconds then release it and the disc will be positioned about 5 millimeters above the tray for easy visual alignment Figure 14 Adjusting the Printer Stand 13 NOTE TO USERS OF SIGNATURE AND SIGNATURE II CD COLOR PRINTERS Due to a slight difference in CD Tray length between these earlier models the instructions for adjusting the printer on the Printer Stand may not lead you to a perfect alignment As an alternative to the procedure explained in the printer stand instruction sheet simply remove the adjustable printer stand top pla
9. he Printer Stand making sure that the silver locating pins are inserted into the locating holes on the bottom of the printer Figure 8 Mounting Printer Onto Stand 11 6 Connect the other end of the Printer Control Cable to the printer s rear panel 6 pin mini DIN port Figure 9 Connecting the Printer Control Cable 7 Connect both ends of the Parallel Cable One end is connected to the Parallel Input Port on the rear panel of the printer The other end is connected to your PC s Parallel Printer Output Port Be sure that your PC s LPT1 port or other parallel port is set to ECP mode If you don t know how to do this consult your printer and PC technical manuals for more information Figure 10 Connecting the Printer Parallel Cable 8 Apply power to the printer by connecting the printer s Power Supply cord to the printer s rear panel Power Input Port Connect the other end to a suitable wall outlet Figure 11 Connecting Power to Signature 111 CD Printer 9 Apply power to Conductor by plugging in the cord on the other side of the Power Adapter to a suitable wall outlet You ve now completed the assembly and cabling of the Conductor Go on to the next section for a quick Hardware Test You ll be printing discs shortly 12 B Hardware Test 1 Load the Input Bin with at least 4 5 CDs and place the output bin in the proper location Figure 12 Loading CDs 2 Press the Sequence Button on Conductor s
10. ly detect which printer is being used by where you place the Bins 2 Connect the Printer Control Cable that was included with your Printer Stand Insert it into the Conductor s rear panel 6 pin mini DIN socket Don t connect the other end yet Figure 4 Connecting the Printer Control Cable 3 Apply power to the Conductor by connecting the Power Supply cord to the Conductor s rear panel Power Input Port Don t plug the other end into a wall outlet yet ie S 1 A new Figure 5 Connecting Power to Conductor 4 Attach the Printer Stand to the Conductor by locating the connecting tabs and inserting them into the appropriate slots on the rear panel of the Conductor See illustration below for the slot locations For the Signature 111 CD Color Printer the stand is attached so that it is centered on Conductor as shown in Figure 6 For the Inscripta Thermal CD Printer the printer is mounted on the left side of the Conductor as shown in Figure 2 10 Figure 6 Attaching the Printer Stand Make sure that the Printer Control Cable is routed neatly out the back of the Printer Stand so that it can be connected to your printer If you are using the Inscripta Thermal CD Printer you will also need to install a Tray Support Bracket to the top cabinet of the Conductor Follow the instructions packed with the Thermal Printer Printer Stand for installation of this bracket 5 Place the printer on top of t
11. may cause undesired operation For Users in the United States This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Re orient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Use of shielded cables is required to comply with the Class B limits of Part 15 of the FCC Rules You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate and or obtain warranty service for this equipment For Users in Canada This digital apparatus does not exce
12. s such as radiators or air ducts or in a place subject to direct sun light excessive dust mechanical vibration or shock C Unpacking and Inspection Before you begin make sure that you have the following items e Conductor Printer Autoloader including Power Supply and Input Output Bins e Signature Signature II or Signature 111 CD Color Printer or Inscripta CD Thermal Printer e Printer Power Supply e Parallel Printer Cable must be IEEE 1284 compliant e Optional Printer Stand with Printer Control Cable 6 pin mini DIN You ll also want to save the box and packing materials It makes transporting or shipping your Conductor much easier if this is ever needed some time in the future D Identifying the Parts Illustrated in Figures 1 and 2 are two Conductors the first with a Signature 111 CD Color Printer attached and the other with an Inscripta Thermal CD Printer attached Look over all items identified to make sure that you are familiar with each Figure 3 shows the rear panel of Conductor Front Panel and Top Ink Jet CD Printer CD Printer Tray Sequence Button Control Bi Output Bin Panel Pause Button Figure 1 Conductor and Signature 111 CD Color Printer Thermal CD Printer CD Printer Tray Input Bin Robotic Arm Control Sequence Button Panel Pause Button Figure 2 Conductor and Inscripta Thermal CD Printer Rear Panel This illustration shows the input ports found on the rear panel of Conductor
13. tCS ii dines nant EE 15 C Technical Support eeaeee a en dutuey esis O EANA eds 15 SECTION 5 TECHNICAL SPECIFICATIONS 0 0 iia 16 SECTION 1 GETTING STARTED A Introduction Thank you for purchasing a Conductor Printer Autoloader This device automates the transport of up to 50 optical discs CD R DVD R etc per batch into and out of a Primera Technology Signature II CD Color Printer or Inscripta Thermal CD Printer Designed for reliable unattended operation Conductor will automatically and effortlessly print anything from a just a few CDs to hundreds or thousands of discs per day Conductor is suitable for use in office or production environments and fits conveniently on any desktop To begin using your new Conductor please read this entire manual carefully You will also need to reference the Operator s Manual for the CD printer you ll be using with Conductor so be sure to have it handy before proceeding Owners of earlier model FARGO Signature and FARGO Primera Technology Signature II CD Color Printers may also integrate their printers to Conductor However a slight modification to the installation procedure explained later in this manual will likely be necessary B Choosing a Good Location e Place Conductor in a location with adequate air circulation to prevent internal heat build up You ll need a tabletop with at least 30 76cm of depth for adequate clearance e Do not place the unit near heat source
14. te Align the printer and allow it to sit on the stand without the aid of the Locating Pins Of course you ll need to be careful not to bump the printer If you do the alignment will need to be reset 7 Press the Pick Button again The CD will be picked up by the Robotic Arm 8 Press the Sequence Button The Robotic Arm will swing over to and above the Output Bin 9 Press the Pick Button The CD drops into the Output Bin 10 Press the Sequence Button again The Robotic Arm returns to a position above the Input Bin 11 Press the Pause and Pick Buttons together at the same time This will reset the Conductor You have completed the test procedure and are now ready to start your first print job C Printing Your First Job Operation is really very simple just print to your printer as you normally would as if no autoloader were installed Specify the quantity you wish to print load discs and Conductor will automatically pick your discs from the Input Bin feed them into the printer print each disc and transport finished discs to the Output Bin Here are a few other steps you ll want to review before starting your first print job 1 Install the printer driver software on your PC according to the instructions in the printer Operator s Manual 2 Design your text graphics and photos in any popular graphics software such as CorelDRAW Adobe Illustrator or any other Windows based program The printer also comes with an excellent disc
Download Pdf Manuals
Related Search