PRIMERGY BX620 S3 2-way Server Blade
Contents
1. Figure 22 Diagnostic LEDs gt Press the diagnostics button D to locate a defective component via its glowing diagnostics LED The meaning of the LEDs is explained in the following table BX620 S3 Service Supplement 37 MAC iSCSI Address Label Diagnosis and Maintenance LED But Meaning ton SAS controller with PCI module error I O daughter card error CPU 2 error CPU 1 error FBD module DIMM 5 8 error FBD module DIMM 1 4 error Table 3 Meaning of the diagnostic LEDs O a RR oO rm 5 2 MAC iSCSI Address Label The following figure shows the position of the labels with the MAC and iSCSI addresses of the onboard LAN controllers a m vy wa Figure 23 MAC ISCSI address labels 38 Service Supplement BX620 S3 Diagnosis and Maintenance DIP Switch Settings 5 3 DIP Switch Settings Figure 24 Position of the DIP switches The server blade is delivered with the DIP switches set in the following positions Switch Function Default 1 Delete password OFF 2 Clear CMOS memory OFF 3 Restore system BIOS OFF 4 Top block swap enabled OFF 5 Switch for keyboard mouse controller ON 6 Not assigned Table 4 Preset DIP switches The switch settings2. Abbreviations FC GAM HDD HU yo IDE LAN LCD LED MGA MRL NIC Fibre Channel Global Array Manager Hard Disk Drive Height Unit Input Output Identification Integrated Drive Electronics Internet Protocol Local Area Network Liquid Crystal Display Light Emitting Diode MEG Array Manual Retention Latch Network Interface Card 48 Service Supplement BX620 S3 Abbreviations NMI Non Maskable Interrupt PCI Peripheral Component Interconnect PDA Prefailure Detection and Analyzing POST Power On Self Test PSU Power Supply Unit RAID Redundant Arrays of Independent Disks ROM Read Only Memory SAN Storage Area Network SAS Serial Attached SCSI SATA Serial Advanced Technology Attachment SCA Single Connector Attachment SCSI Small Computer System Interface SCU Server Configuration Utility SFP Small Form Factor Pluggable BX620 S3 Service Supplement 49 Abbreviations USB Universal Serial Bus VGA Video Graphics Adapter VPD Vital Product Data WOL Wakeup On LAN 50 Service Supplement BX620 S3 Index A add on modules 43 B battery replace 34 server blade 34 BIOS recover 41 Cc consumables 15 control panel board 23 remove 24 25 replace 23 D diagnostic LEDs 37 DIP switch settings 39 DIP switches 39 disposal 16 documentation 5 dummy heat sink 27 33 E electrostatic sensitive devices 14 energy save 1
3. clean the top of the processor Use a lint free Isopropyl alcohol wipe e g CleanTex TexPad 801 available from specialist dealers gt Apply a new film of thermal paste to the bottom of the heat sink 30 Service Supplement BX620 S3 Replacement Routines Exchanging Processors To install a new heat sink you must take off the protective cover over the thermal paste Figure 17 Removing the plastic cover gt Take the heat sink in your hand and remove the transparent protective cover over the thermal paste on the bottom of the heat sink BX620 S3 Service Supplement 31 Exchanging Processors Replacement Routines As E S NEID 2 P Figure 18 Fastening the processor heat sink gt Place the heat sink on the CPU and fix it by fastening the four premounted screws in diagonally opposite sequence ATTENTION If you do not add a second processor to the server blade a dummy heat sink must be installed on the second processor socket to make sure that all server blade modules are cooled sufficiently 32 Service Supplement BX620 S3 Replacement Routines Exchanging Processors Installing the Dummy Heat Sink Figure 19 Installing the dummy heat sink gt Place the dummy heat sink over the the processor socket as shown in the figure and fasten it with two screws arrows BX620 S3 Service Supplement 33 Replacing the Battery Replacement Routines 4 4 Repl
4. 20 S3 Preface Notational Conventions 1 2 Notational Conventions The following notational conventions are used in this manual quotation marks indicate names of chapters and terms that need to be emphasized gt indicates an activity that must be performed point your health the correct functioning of your system or the security of your data may be at risk il indicates supplementary information remarks and tips ATTENTION indicates that if you ignore the information given at this Table 2 Notational conventions BX620 S3 Service Supplement 7 2 Procedure ATTENTION The activities described in this manual should only be performed by engineers service personnel or technical specialists gt First of all please familiarize yourself with the safety instructions in the chapter Important Notes on page 1 1ff Make sure that all the manuals you need see service DVD are available printing out the PDF files if necessary You will definitely need the Operating Manual of the basic unit Shutdown the server blade correctly switch it off and remove it from the basic unit as described in the chapter Replacement Routines on page 19f Replace the defective component as described in the relevant chapter Close the server blade Start the server blade vo v vv If necessary configure the operating system as required See Operating Manual BX620 S3
5. 26361 F3313 L522 MEM 2GB 2X1GB FBD667 PC2 5300F D ECC 34000447 S26361 F3230 L522 MEM 4GB 2X2GB FBD533 PC2 4200F D ECC 88039900 S26361 F3313 L523 MEM 4GB 2X2GB FBD667 PC2 5300F D ECC 34000448 S26361 F3230 L523 MEM 8GB 2X4GB FBD533 PC2 4200F D ECC 88039901 S26361 F3313 L524 BX620 S3 Service Supplement 43 Spare Parts and Add On Modules Diagnosis and Maintenance 1 Name Mat no Product no Storage Modules 75 SATA BOARD 88039957 SNP A3C40068922 75 SAS MODUL 88039958 SNP A3C40069852 75 SAS PCI X 88039959 SNP A3C40068919 75 SAS PCI E 88039960 SNP A3C40068921 SAS RAID MODUL 88039961 SNP A3C40069856 ITBBU LSI 256MB BRO 88039962 SNP A3C40074700 RAID KEY LSI I BUTTON SAS RAID CARD 88039963 SNP A3C40072799 1 0 Modules Daughter Cards 72 ETHERNET I O_ROHS 88040153 SNP A3C40073437 FC DAUGHTER BOARD FOR BX 6 ROHS 88039627 SNP A3C40073438 VO Controller PCI extension ETH CTRL 2X1GBIT PCIE PRO 1000PT CU LP 88040024 INE EXPI9402PTG2L20 ETH 2X1GBIT PCI X PRO 1000MT CU LP R 84003532 INE PWLA8492MTG2L20 R FC CTRL 2GBIT S LP1050 MMF LC LP 88039400 SNP A3C40068646 FC CTRL 2CHANNEL4GBIT S LPE11002 MMF LC 88040027 SNP A3C40074398 SCSI 1XU160 CONTROLLER INT EXT LP 88039565 ADT ASC 29160LP FSCROHS Hard disk modules HDD SATA 60GB 7 2K HOT P
6. 5 environmental protection 15 ESD modules with electrostatic sensitive devices 14 H heat sink dummy module 27 33 fasten 32 remove 27 L labels 15 MAC iSCSI addresses 38 legend 7 lithium battery 13 34 N notational conventions 7 notes on safety 11 P packaging 15 processor insert 28 processors install remove 27 R recover BIOS 41 recovery BIOS 41 recycling 16 replace battery 34 S server energy save 15 environmental protection 15 server blade battery 34 BIOS 41 open 22 remove from basic unit 20 service DVD 5 spare parts 43 T take back 16 target group 5 BX620 S3 Service Supplement 51 pee A o i uu a es ee e e eee ts Fujitsu Siemens Computers GmbH User Documentation 33094 Paderborn Germany Fax 0 700 372 00001 e mail manuals fujitsu siemens com http manuals fujitsu siemens com Comments Suggestions Corrections Submitted by Comments on PRIMERGY BX620 S3 2 way Server Blade BX620 S3 co FUJITSU Information on this document On April 1 2009 Fujitsu became the sole owner of Fujitsu Siemens Compu ters This new subsidiary of Fujitsu has been renamed Fujitsu Technology So lutions This document from the document archive refers to a product version which was released a considerable time ago or which is no longer marketed Please note that all company references and copyrights in this document have been legally transferred to Fujitsu Technology Sol
7. Incorrect replacement of batteries can lead to risk of explosion The batteries must be replaced with an identical battery or with a battery type recommended by the manufacturer e Do not throw batteries into the trash can Please dispose of them in accordance with local regulations for special refuse e When replacing the lithium battery in the relevant components always follow the instructions in this manual e All batteries containing pollutants are marked with a symbol a crossed out garbage can The marking also contains the chemical symbol of the heavy metal that classifies the battery as a pollutant Cd Cadmium Hg Mercury Pb Lead BX620 S3 Service Supplement 13 Electrostatic Sensitive Devices Important Notes Modules with electrostatic sensitive devices Modules with electrostatic sensitive devices are identified by the following A Atlas When handling modules with ESDs it is essential that you observe the following guidelines Figure 1 ESD label e You must always discharge static build up e g by touching a grounded object before working with such components e Any devices or tools that are used must be free of electrostatic charge e Always hold components with ESDs at the edges e Do not touch any connectors or conduction paths on an ESD e Wear a suitable grounding cable that connects you to the external chassis of the basic unit e Place all the components on a pad which is free of elec
8. LUG 2 5 88039964 S26361 F3209 L60 HDD SAS 36GB 10K HOT PLUG 2 5 88039966 S26361 F3208 L136 HDD SAS 73GB 10K HOT PLUG 2 5 88039967 S26361 F3208 L173 FRAME HDD 2 5 module frame for 2 5 hard disk 88039952 SNP A3C40058359 DUMMY 2 5 KPL hard disk dummy module 88039969 SNP A3C40071759 Front Control Panel Control panel board with cable 88039954 SNP A3C40075578 TMaterial number from the ErsinXP database 44 Service Supplement BX620 S3 Diagnosis and Maintenance Spare Parts and Add On Modules Current information about BX620 S3 spare parts and add on modules is also provided by the interactive PRIMERGY BX6xx Illustrated Spares Catalogue This catalogue can be downloaded from Internet At the FSC extranet service site http extranet fujitsu siemens com service you can go to the spares portal by clicking Illustrated Spares Catalogue under the rubric PRIMERGY BX620 S3 Service Supplement 45 Abbreviations ASR amp R Automatic Server Reconfiguration and Restart BIOS Basic Input Output System CD Compact Disk COM Communication CPU Central Processing Unit DBMS Database Management System DDR Double Data Rate RAM DIMM Dual Inline Memory Module DVD Digital Versatile Disk ECC Error Correcting Code EDC Error Detection Code EMC Electromagnetic Compatibility ESD ElectroStatic Discharge Electrostatic Sensitive Device BX620 S3 Service Supplement 47
9. PRIMERGY BX620 S3 2 way Server Blade Service Supplement Edition November 2006 Comments Suggestions Corrections The User Documentation Department would like to know your opinion of this manual Your feedback helps us optimize our documentation to suit your individual needs Fax forms for sending us your comments are included in the back of the manual There you will also find the addresses of the relevant User Documentation Department Certified documentation according to DIN EN ISO 9001 2000 To ensure a consistently high quality standard and user friendliness this documentation was created to meet the regulations of a quality management system which complies with the requirements of the standard DIN EN ISO 9001 2000 cognitas Gesellschaft f r Technik Dokumentation mbH www cognitas de Copyright and Trademarks Copyright O 2006 Fujitsu Siemens Computers GmbH All rights reserved Delivery subject to availability right of technical modifications reserved All hardware and software names used are trademarks of their respective manufacturers Contents 1 PERCE us Eid ere a tee eed 5 1 1 Documentation Overview 5 1 2 Notational Conventions lt lt 7 2 PROCEQUES uu v uode SEN Ron SRR See REOR Ws 9 3 Important Notes rlrnens 11 3 1 Notes on Safety cc usa sa aa ee a ana 11 3 2 Environmental Protection 15 4 Replacement Ro
10. Service Supplement 9 3 Important Notes This chapter provides safety instructions which you must observe when handling your system 3 1 Notes on Safety il The following safety instructions can also be found in the manual entitled Safety This device complies with the relevant safety regulations for IT equipment including electronic office machines for use in an office environment If you have any questions contact your sales outlet or the Fujitsu Siemens Computers customer service center ATTENTION The activities described in this manual should only be performed by engineers service personnel or technical specialists Equipment repairs should only be performed by qualified staff Any failure to observe the guidelines in this manual could endanger the user through electric shock fire hazards or damage the equipment Please note that any unauthorized opening of the device will result in the invalidation of the warranty and exclusion from all liability Before setting up ATTENTION e During installation and before operating the device observe the instructions on environmental conditions for your device see Operating Manual e Ifthe device is brought in from a cold environment condensation may form both inside and on the outside of the machine Before operating the device wait until it is absolutely dry and has reached approximately the same temperature as the installation site Any failure to observe t
11. acing the Battery To allow permanent saving of the system information a lithium battery is installed which supplies the CMOS memory with power If the battery voltage is too low or the battery is empty a corresponding error message is displayed In this case the lithium battery must be replaced In your server blade the CMOS battery is located between the connectors for the optional I O module Figure 20 Position of the CMOS battery ATTENTION Observe the safety notes and the information on handling batteries in the section Batteries on page 13 Incorrect replacement of batteries can lead to risk of explosion The batteries must be replaced with an identical battery or with a battery type recommended by the manufacturer 34 Service Supplement BX620 S3 Replacement Routines Replacing the Battery ATTENTION Make sure you insert the lithium battery the right way round the positive pole must be on top Figure 21 Replacing the battery gt Press the locking lever in the direction of the arrow 1 and remove the battery from its carrier 2 gt Inserta new lithium battery of identical type into the carrier 3 and engage it with the lever 4 BX620 S3 Service Supplement 35 5 Diagnosis and Maintenance 5 1 Server Blade Diagnostics LEDs Diagnostic LEDs help to locate defective components in the server blade
12. are Parts and Add On Modules 5 5 Spare Parts and Add On Modules The following spare parts and add on modules are available for the PRIMERGY BX620 S3 2 way server blade Name Mat no Product no S75 CPU BLADE BX server blade with type label 88040152 S26361 K921 V906 without processors and memory modules S75 CPU BLADE BX server blade with type label S26361 K921 V907 without processors and memory modules compliant with Clovertown processor see page 26 Processors without heat sink CPU XEON DP 5050 3 0GHz 2X2MB 667MHz 88039894 V26808 B7970 V12 CPU XEON DP 5080 3 73GHZ 2X2MB 1066MHZ 88040015 V26808 B7971 V12 CPU XEON DP 5110 1 60GHZ 4MB 1066MHZ 88040586 V26808 B8011 V10 CPU XEON DP 5130 2 00GHZ 4MB 1333MHZ 88040588 V26808 B8012 V10 CPU XEON DP 5140 2 33GHZ 4MB 1333MHZ 88040589 V26808 B8012 V11 CPU XEON DP 5150 2 66GHZ 4MB 1333MHZ 88040696 V26808 B8012 V12 CPU XEON DP 5160 3 00GHZ 4MB 1333MHZ 88040697 V26808 B8012 V13 CPU XEON DP5060 3 2GHz 2x2MB 1066MHz 88039895 V26808 B7971 V10 CPU XEON MV DP 5063 3 2GHZ 2X2MB 88040089 V26808 B7971 V20 1066MHZ HEATSINK S72 PASSIV 88039953 SNP A3C40071303 HEAT SINK DUMMY MODULE 84003686 SNP A3C40073433 Memory Modules MEM 1GB 2X512MB FBD533 PC2 4200F ECC 88039898 S26361 F3313 L521 MEM 1GB 2X512MB FBD667 PC2 5300F ECC 34000446 S26361 F3230 L521 MEM 2GB 2X1GB FBD533 PC2 4200F D ECC 88039899 S
13. cated on a board that is connected to the system board of the server blade via a foil cable Figure 7 Control panel board with connection cable Requirements The server blade has been removed The cover of the server blade has been removed ATTENTION Make sure you observe the safety notes in the chapter Important Notes on page 1 1ff BX620 S3 Service Supplement 23 Replacing the Control Panel Board Replacement Routines Removing the Control Panel Board PS d W xe Figure 8 Pulling off the foil cable gt Loosen the clamping bracket A and disconnect the cable of the control panel board from the connector on the system board Figure 9 Unfastening the control panel board Undo the screw 1 and pull the control panel module out of the bay 2 24 Service Supplement BX620 S3 Replacement Routines Replacing the Control Panel Board Figure 10 Removing the control panel board Remove the control panel board from the server blade chassis Installing the Control Panel Board To install the control panel board follow the above procedure in reverse BX620 S3 Service Supplement 25 Exchanging Processors Replacement Routines 4 3 Exchanging Processors You can install one or two processors of type Intel XEON DC in the PRIMERGY BX620 S3 server blade The server blade supports Dempsey processors and the next processor
14. f possible do not stick your own self adhesive labels on plastic housing parts as this can hamper the recycling process BX620 S3 Service Supplement 15 Electrostatic Sensitive Devices Important Notes Returning used electrical and electronic devices Separate disposal Old electrical and electronic devices should be disposed of separately and not with household refuse Separate disposal allows this old equipment to be reused or recycled which helps conserve resources Return and collection systems lt may be possible to return old electrical electronic devices from private households free of charge Please use the country specific return or collection systems available to you see Local contacts on page 17 The return of used devices which pose a health or safety risk for human beings due to soiling during use may be refused Reuse and recycling By actively using any return or collection systems offered you will be contrib uting to the reuse and recycling of electrical electronic devices Effects on the environment and human health Old electrical electronic devices contain parts which must be handled selec tively according to EU directives Separate disposal and selective treatment are the basis for environment friendly disposal and the protection of human health Meaning of the symbol Crossed out trash can on wheels In accordance with EU directives electrical electronic devices which are marked with o
15. generation Woodcrest and Clovertown see Spare Parts and Add On Modules on page 43 Important Note The Clovertown processor ist only compliant with part number A3C40083121 server blades You can find out the server blade part number as follows You can retrieve the part number with the web based GUI of the management blade Enter the menu Server Blade Blade Info for the concerning server blade and look for the value of the field Model see the manual PRIMERGY BX Blade Server Systems RemoteView Management User Interface Description You can read the part number from a label located on the underside of the server blade chassis The figure below shows the position of the part number label A i Bild 11 Part number label position arrow 26 Service Supplement BX620 S3 Replacement Routines Exchanging Processors ATTENTION e Always use processors of the same type All processors must have the same frequency and cache size For multi processor mode use a suitable multi processor operating system e Never touch the processor core e The thermal paste must be intact for mounting the processor e Never install a processor without a heat sink The processor is likely to overheat which may cause damage to the processor and the system board Requirements The server blade has been removed The cover of the server blade has been removed Removing t
16. have the following meaning BX620 S3 Service Supplement 39 DIP Switch Settings Diagnosis and Maintenance Switch 1 ON Delete password enabled OFF Delete password disabled Switch 2 ON Clear CMOS memory enabled OFF Clear CMOS memory disabled Switch 3 ON Restore system BIOS enabled OFF Restore system BIOS disabled Switch 4 ON Top block swap enabled OFF Top block swap disabled Switch5 ON Keyboard mouse controller cannot be programmed normal operation OFF Keyboard mouse controller can be programmed Switch6 ON Not assigned OFF Not assigned 40 Service Supplement BX620 S3 Diagnosis and Maintenance Recovering the Server Blade BIOS 5 4 Recovering the Server Blade BIOS This section describes how to recover the BIOS of a server blade in the event of an error ATTENTION This procedure must only be used in the event of an error Requirements The basic unit is connected to the mains The server blade has been switched off There is an external USB floppy disk drive Creating a BIOS Flash Floppy Disk gt Extract the BIOS update ZIP archive file on a PC hard disk The data for creating the BIOS flash floppy disk is contained in the software pool http support fujitsu siemens com com support downloads html gt Insert an empty floppy disk into the floppy disk drive gt Run the downloaded FSC_nnnn exe file and follow the instructions on the screen to create a BIOS flash floppy di
17. he Heat Sink Undo the four screws which fasten the processor heat sink and remove it BX620 S3 Service Supplement 27 Exchanging Processors Replacement Routines Inserting the Processor v e Figure 13 Releasing the locking lever of the processor socket gt Press the locking lever of the processor socket out of its locking position arrows and swivel it upward Figure 14 Opening the locking frame of the processor socket gt Open up the locking frame of the processor socket and take off the black protective cover arrow 28 Service Supplement BX620 S3 Replacement Routines Exchanging Processors Figure 15 Inserting the processor Place the processor on the socket and make sure the marks on the processor point to the corresponding marks on the socket a BX620 S3 Service Supplement 29 Exchanging Processors Replacement Routines Figure 16 Closing the locking frame of the processor socket Close the locking frame of the processor socket 1 swivel the locking lever downward 2 and lock it under the small clip a that is attached to the socket Installing the Heat Sink ATTENTION Before installing the heat sink check that the thermal paste is intact If it is not you must do the following before reinstalling the heat sink Remove any remnants of the thermal paste from the bottom of the heat sink and
18. he guidelines in this manual could damage the equipment BX620 S3 Service Supplement 11 Notes on Safety Important Notes ATTENTION Transport the device only in its original packaging or in packaging which protects it from knocks and jolts Installation and operation ATTENTION Read the notes on installation and operation in the Operating Manual of the PRIMERGY BX600 S2 basic unit When installing the server blade in the basic unit beware of the energy hazard at the midplane conctacts A short circuit on these contacts may damage the system Data cables must be adequately shielded to avoid interference For the LAN wiring the requirements according to standards EN 50173 and EN 50174 1 2 apply The minimum requirement is the use of a protected LAN line of category 5 for 10 100 Mbps Ethernet and or of category 5e for Gigabit Ethernet The requirements of the specification ISO IEC 11801 must also be taken into account Route the cables in such a way that they do not form a potential hazard tripping and cannot be damaged When connecting the device refer to the relevant notes in the Operating Manual Do not connect or disconnect any data transmission cables during a thunderstorm lightning hazard Be careful to ensure that no objects e g jewelry paper clips etc or liquids get inside the device electric shock short circuit In emergencies e g damaged casing elements or cables penetration of liquid
19. ion in the chapter Important Notes on page 1 1ff 4 1 Preparation If you want to replace components which are not hot pluggable you must remove the server blade from the basic unit and open it gt Exit all applications and shut down the server blade correctly Press the On Off button on the server blade control panel BX620 S3 Service Supplement 19 Preparation Replacement Routines Removing the Server Blade from the Basic Unit gt Press the two touch points 1 to unlock the ejection levers gt Open out the two ejection levers 2 simul taneously to disengage the server blade Figure 4 Removing the server blade 20 Service Supplement BX620 S3 Replacement Routines Preparation were 422254544 Figure 5 Removing the server blade gt Pull the server blade out of the basic unit BX620 S3 Service Supplement 21 Preparation Replacement Routines Removing the Cover gt Press the two touch points 1 of the cover simultaneously to disengage it and slide back the cover as far as it will go in the direction of the arrow 2 gt Take off the cover The server blade components are now freely accessible 22 Service Supplement BX620 S3 Replacement Routines Replacing the Control Panel Board 4 2 Replacing the Control Panel Board The electronic elements of the control and connection panel of the server blade are lo
20. ne of the following symbols must not be disposed of with household refuse Figure 2 Symbols on electrical electronic devices 16 Service Supplement BX620 S3 Important Notes Electrostatic Sensitive Devices Returning batteries According to EU directives batteries which are marked with one of the following symbols must not be disposed of together with household refuse A Figure 3 Symbols on batteries With batteries containing harmful substances the chemical symbol for the heavy metal contained is indicated below the trash can Cd Cadmium Hg Mercury Pb Lead The following applies to Germany Private consumers can return batteries at the point of sale or in the immediate vicinity thereof free of charge The consumer is obligated to return defective or used batteries to the seller or to the return points established for this purpose Local contacts For details on take back and reuse of devices and consumables within Europe contact your Fujitsu Siemens Computers branch office subsidiary or our recycling centre in Paderborn Germany Fujitsu Siemens Computers Recycling Center 33106 Paderborn Germany Tel 49 5251 8180 10 Fax 49 5251 8180 15 Internet www fujitsu siemens com recycling BX620 S3 Service Supplement 17 4 Replacement Routines ATTENTION When working with systems and boards make sure you observe the safety informat
21. ntation for the server blade models available for the PRIMERGY BX620 S3 basic unit These PDF files can also be downloaded from the Internet free of il charge At http manuals fujitsu siemens com you will find an overview page showing the online documentation available on the Internet You can go to the PRIMERGY Server documentation by clicking on industry standard servers BX620 S3 Service Supplement 5 Documentation Overview Preface Information Activity Manual Features and technical data of the server blade Installation and initial operation such as Connections to the basic unit Operation Configuring the server blade Firmware update server blade BIOS and BMC Installing the server blade in the basic unit BIOS setup Troubleshooting Installing removing hot plug components Hard disk modules Operating Manual Extensions and conversions Installing memory modules Adding processors Replacing the storage module Options Guide Replacement routines Replacing the control panel Exchanging the processor Replacing the CMOS battery Diagnostics Diagnostic LEDs MAC iSCSI address labels BIOS recovery DIP Switch Settings Spare parts list Service Supplement Detailed safety information Safety manual Table 1 Overview of the BX620 S3 server blade documentation 6 Service Supplement BX6
22. s or foreign bodies switch off the device immedi ately unplug it from the grounded power outlet and contact your customer service centre ATTENTION Proper operation of the device in accordance with IEC60950 EN 60950 is only ensured if the casing is completely assembled and the rear covers for the installation openings are in place electric shock cooling fire protection interference suppression Service Supplement BX620 S3 Important Notes Notes on Safety ATTENTION e Install only system extensions that satisfy the requirements and rules governing safety electromagnetic compatibility and telecommunica tions terminal equipment If you install other extensions you may damage the system or violate these safety regulations Information on which system extensions are suitable can be obtained from the customer service center or your sales outlet e The components marked with a warning label e g lightning symbol may only be opened removed or exchanged by authorized qualified personnel with the exception of the hot plug hot swap components e Ifyou cause a defect on the device by installing or exchanging system extensions the warranty will be invalidated e You may only set the resolutions and refresh rates specified in the operating manual for your monitor Otherwise you may damage the monitor If you are in any doubt contact your sales outlet or customer service center Batteries ATTENTION e
23. sk Recovering the Server Blade BIOS gt Connect the monitor keyboard and mouse to the KVM connector on the rear of the blade server chassis see Operating Manual Remove the server blade from the blade server chassis see page 20 and open it gt Set switch 3 of the DIP switches on the system board to ON see figure 24 on page 39 Close the cover of the server blade and reinstall it in the blade server chassis see page 19 gt Insert the BIOS flash floppy disk in a USB floppy disk drive and connect the floppy disk drive to the USB port of the server blade using the USB breakout cable see Operating Manual BX620 S3 Service Supplement 41 Recovering the Server Blade BIOS Diagnosis and Maintenance Press the KVM button on the control panel of the server blade see Operating Manual to switch the keyboard mouse and the monitor of the KVM blade to the server blade Switch on the server blade see Operating Manual After a short beep the BIOS is uploaded The status of the flash process is displayed on the KVM console After the flash is completed instructions are displayed for the following procedure gt Switch off the server blade Remove the server blade and open it Set switch 3 of the DIP switches on the system board to OFF Close the server blade and reinstall it vo v vv Now you can put the server blade back into operation 42 Service Supplement BX620 S3 Diagnosis and Maintenance Sp
24. trostatic charge For a detailed description of how to handle ESD components see the relevant European and international standards EN 61340 5 1 ANSI ESD S20 20 14 Service Supplement BX620 S3 Important Notes Electrostatic Sensitive Devices 3 2 Environmental Protection Environmentally friendly product design and development This product was designed in compliance with the Fujitsu Siemens Computers standard on environmentally friendly product design and development This means that the designers have taken into account crucial criteria such as durability selection and labeling of materials emissions packaging the ease with which the product can be dismantled and the extent to which it can be recycled This saves on resources and helps to protect the environment Notes on saving energy Devices that do not have to be on permanently should not be switched on until they are needed and should be switched off during long breaks and when work is finished Notes on packaging Do not throw away the original packaging as you may need it for future transport If possible the device should be transported in its original packaging Notes on dealing with consumables Please dispose of printer consumables and batteries in accordance with local regulations Do not throw batteries into the trash can They must be disposed of in accor dance with local regulations on special waste Notes on labeling plastic housing parts I
25. utines 19 4 1 Preparation gt sac cosacos istasa eee eee 19 4 2 Replacing the Control Panel Board 23 4 3 Exchanging Processors 852 eae 26 4 4 Replacing the Battery 34 5 Diagnosis and Maintenance 37 5 1 Server Blade Diagnostics LEDs 37 5 2 MAC iSCSI Address Label 38 5 3 DIP Switch Settings ens 39 5 4 Recovering the Server Blade BIOS 41 5 5 Spare Parts and Add On Modules 43 ADBIEVIAHONS uis s nou chee eh be eee e OG4 ROBES 47 MAOK EE 51 BX620 S3 Service Supplement 1 Preface The PRIMERGY BX620 S3 2 way Server Blade is an Intel based server blade that can be operated in the PRIMERGY BX600 S2 basic unit 1 1 Documentation Overview Concept and target groups This Service Supplement supplements the information contained in the Operating Manual ATTENTION The activities described in this manual may only be performed by specialist personnel with technical training The installation and removal of the hot plug components is described in the Operating Manual supplied with the server Service DVD A service DVD is available for service partners of Fujitsu Siemens Computers This DVD contains the following manuals in PDF format the Safety manual the Ergonomics manual the Operating Manual for PRIMERGY BX620 S3 the docume
26. utions Contact and support addresses will now be offered by Fujitsu Technology So lutions and have the format ts fujitsu com The Internet pages of Fujitsu Technology Solutions are available at http ts fujitsu com and the user documentation at http manuals ts fujitsu com Copyright Fujitsu Technology Solutions 2009 Hinweise zum vorliegenden Dokument Zum 1 April 2009 ist Fujitsu Siemens Computers in den alleinigen Besitz von Fujitsu bergegangen Diese neue Tochtergesellschaft von Fujitsu tr gt seit dem den Namen Fujitsu Technology Solutions Das vorliegende Dokument aus dem Dokumentenarchiv bezieht sich auf eine bereits vor l ngerer Zeit freigegebene oder nicht mehr im Vertrieb befindliche Produktversion Bitte beachten Sie dass alle Firmenbez ge und Copyrights im vorliegenden Dokument rechtlich auf Fujitsu Technology Solutions bergegangen sind Kontakt und Supportadressen werden nun von Fujitsu Technology Solutions angeboten und haben die Form ts fujitsu com Die Internetseiten von Fujitsu Technology Solutions finden Sie unter http de ts fujitsu com und unter Attp manuals ts fujitsu com finden Sie die Benutzerdokumentation Copyright Fujitsu Technology Solutions 2009
Download Pdf Manuals
Related Search