9016 Upgrade Instructions - Pdfstream.manualsonline.com
Contents
1. BA GASKET a SOLENOIDS OOOOOOO 22223 CALIBRATION DH200 MANIFOLD PC 206 ADUUBISION Figure 1 O 0 16 Exploded View of 9016 Scanner RUN REF NG PURGE CAL REF O O 9106 I POIN A Se ee Figure 2 9016 Top Plate 2 www PressureSystems com Pressure Systems Inc 9016 Upgrade Instructions When performing any type of maintenance of NetScanner System components the following guidelines and precautions should always be followed e Verify that the work area and technicians are properly grounded to prevent damage to electronic components due to electrostatic discharge Ensure that all electrical and pneumatic connections have been removed from the module Ensure that the work area is free of dust and other possible contaminants that may affect the high tolerance machined parts and pneumatic seals if model has an integral manifold Care must be taken to prevent contaminants from reaching O ring surfaces If O ring surfaces require cleaning use a lint free applicator with acetone to remove dirt and lightly lubricate the O ring surface with Krytox provided in the maintenance kit Never use sharp objects to cut tubing from the bulged tubes The tiny scratches left on the tubes could cause leaks In the process of performing this upgrade the following tools will be required Phillips head screwdriver No 1 preferred and small cut2. from their protective shipping container 1 e prevention of electrostatic discharge damage 2 The calibration valve control wires are attached to connector P6 as shown in Figure 8 The routing of these wires will need to be changed during the upgrade The wires connected to the four pin P6 connector will need to be freed from about one half of the white spiral wire wrap This may be accomplished by unwinding approximately half of the nylon spiral 8 www PressureSystems com Pressure Systems Inc 9016 Upgrade Instructions wire wrap starting near the P6 connector The freed white nylon spiral wire wrap may be re used on other wires or tubes or may simply be cut off and discarded If you choose to cut off the spiral wire wrap be careful not to nick or cut any other wires or tubes 3 Attach the wiring harnesses to their respective connectors P1 P3 and P6 Note that the connector from P3 connects to your new PC 327 board It will be connected to the PC 327 board after the PC 322 323 boards have been attached to the module top plate Remember the red line on your ribbon cable is to be connected to Pin 1 of the PCB 4 Plug the connector from the top plate into P1 of the PC 322 board Be careful to connect the correct pins together Pin to Pinl and make sure the pins are aligned If not the PCB could be damaged Pin 1 is denoted by the square pad on the solder side of the board See Figures 9 9a and 10 Pin 1 denoted by
3. e the one tube beneath the board See Figure 7 Line up the gold pins and gently and slowly press to connect Pay particular attention to the Cl and C4 tubes and ensure they are not crimped or crushed between the PCB and the DH200s See Figures 7 and 7a WARNING Ensure that the board is oriented the same as the board just removed connector pins on the same end as the wiring harness and the gold pins are lined up with and fit easily into the connectors on the DH200s Figure 7 Tubing Routing Underneath PC 327 Board 3 Reinstall the two 2 Phillips head screws to secure the PC 327 board 7 www PressureSystems com Pressure Systems Inc 9016 Upgrade Instructions Sg ett Hart La RP fate Shee el iii ail MES ee ee i Beh E J C4 tube C4 tube Figure 7a PC 327 Board Installing the PC 322 323 Boards As previously mentioned the PC 322 and the PC 323 boards will arrive to you completely connected and may be installed very similarly to the installation of the old PC 280 board See Figure 8 P1 connection J 4 Lal k 5 ee i i jiy n s f f P ERATE a E s r kan i P m az n enli i A ai em E TEEPE p a connection ge E sea ir Ea 7 a d vag i eel os pi a ai Gee g TEn Caste Ba irrg ke a Fy Figure 8 PC 322 323 Boards P6 connection 1 Use the same precautions as previously noted when removing these boards
4. measurement SPECIALTIES 09 00 o PRESSURE SYSTEMS Model 9016 Upgrade Instructions February 2004 NetScanner System www PressureSystems com Pressure Systems Inc 9016 Upgrade Instructions Packing List When you purchase your 9016 Upgrade Kit the following parts will be included 1 9016 Upgrade Installation Instructions 1 Upgrade Tag 1 PC327 analog board 1 Assembled PC322 PC323 processor unit 1 Cable tie 5 5 inch OO OOL Pressure Systems Inc 9016 Upgrade Instructions 9016 Upgrade Instructions The following instructions must be followed to successfully upgrade the hardware and firmware in your current 9016 Intelligent Pressure Scanner to 9116 scanner capabilities Figure 1 is an exploded view of the Model 9016 Please refer to this drawings for an understanding of the construction of Intelligent Pressure Scanners Figure 2 depicts the 9016 top plate 1 www PressureSystems com Pressure Systems Inc 9016 Upgrade Instructions 9016 Upgrade Instructions The following instructions must be followed to successfully upgrade the hardware and firmware in your current 9016 Intelligent Pressure Scanner to 9116 scanner capabilities Figure 1 is an exploded view of the Model 9016 Please refer to this drawings for an understanding of the construction of Intelligent Pressure Scanners Figure 2 depicts the 9016 top plate p a URE SYSTEMS 3 o3 R 7
5. ms Inc 9016 Upgrade Instructions Viton gasket Figure 4 9016 Out of Housing Electronic Circuit Board Replacement Your 9016 contains two 2 electronic circuit boards that must be removed and replaced for this upgrade PC 206 Amplifier Multiplexer Board The following procedures should be used for removal of the PC 206 Amplifier Multiplexer Board Use the tools and follow the general precautions previously described 1 Carefully remove the wiring harness from connector P1 of the PC 206 board See Figure 5 2 Remove the two 2 Phillips head screws securing the PC 206 board to the DH200 transducers Carefully disconnect the PC 206 board from the DH200s by slowly working the board off starting at one end and moving down the length of the board It is important to not break the gold pins when removing the board Inspect the PC 206 boards for broken pins and remove from DH200 transducers if neccessary Wiring harness Phillips head screws clLeerererre eee amp we tte A He a este a sreterererere es EEES i Ley PEs war E r ver Figure 5 PC 206 Board 5 www PressureSystems com Pressure Systems Inc 9016 Upgrade Instructions PC 280 Ethernet Microprocessor A D Board The following procedures should be used for removal of the PC 280 Ethernet Microprocessor A D Board Use the tools and follow the general warnings already described 1 Carefully remove any at
6. ons Final Installation 1 Carefully reinstall the module into the housing aligning the retaining pins in the housing with holes in the brackets on your PC 322 323 boards Ensure that none of the wiring harnesses or nylon tubing are pinched Ensure the Viton gasket is flat between the two surfaces and is without folds Tighten the three screws for this PC 323 board 2 Re install the twelve 12 Phillips head screws around the top plate perimeter 3 Install the upgrade kit tag on the end of your scanner just below the serial number nameplate The tag is designed to fit directly beneath the nameplate Clean the surface of the with isopropyl alcohol to achieve good adhesion Peel off the protective covering layer of double faced tape and position the sticker as described above Final Checkout Test your Intelligent Pressure Scanner for proper operation For operation of your newly upgraded Intelligent Pressure scanner please refer to your 9116 User s Manual available from the Pressure Systems web site www PressureSystems com 1 www PressureSystems com Headquarters Factory Pressure Systems Inc 34 Research Drive Hampton VA 23666 USA Phone 757 865 1243 Toll Free 800 328 3665 Fax 757 865 8744 E mail sales PressureSystems com
7. square solder pad on bottom of PC board CEPEEOOETENIN Figure 9 Finding Pin 1 on a PC Board Orient red stripe as shown Figure 9a Connectors on 322 323 PCB Scanner top plate connection P1 connection on GAN Ja e PC 322 boar d _s j f H I Ai GT Lhi Figure 10 Top Plate to P1 Connection on PC 322 9 www PressureSystems com Pressure Systems Inc 9016 Upgrade Instructions 5 Carefully guide the LEDs on the PC 322 board into their respective holes in the scanner chassis Ensure that all cables and tubing are not crimped or restricted and attach the PC 322 323 boards to the chassis with the three 3 Phillips head screws through the top plate that were previously removed and saved Do not tighten completely 6 Connect the ribbon cable from P3 on the PC 322 323 board to the connector on your PC 327 board red line indicates pin 1 See Figure 11 JT t AT en PC 322 323 sb connection to the PC 327 board THE TEL Figure 11 PC 327 Connection and Cable Tie down Note orientation of red stripe 7 Insert a plastic cable tie down through the tie down mount previously installed and around the clear plastic tubing as shown in Figure 11 The following two pictures show a completed 9016 module upgrade with side and top views Figure 12 Figure 13 Side View of 9016 Upgrade Top View of 9016 Upgrade 10 www PressureSystems com Pressure Systems Inc 9016 Upgrade Instructi
8. tached wiring harnesses from connectors P1 P3 and P6 of the PC 280 board This will require cutting one nylon tie wrap attached to the center mounting bracket See Figure 6 Connector P6 Connector P3 Connector P1 Figure 6 PC 280 Board and Connectors 2 Remove the three 3 2 56 Phillips head screws securing the PC 280 mounting brackets to the top plate These screws will be in line with the PC 280 LEDs that protrude through the top plate Save for later use Carefully lift the board out of the top panel See Figures 6a and 6b r Figure 6b PC 280 Board Three screws to remove PC 280 board Figure 6a 9016 Top Plate 6 www PressureSystems com Pressure Systems Inc 9016 Upgrade Instructions Retain all of the existing connecting cables for use with your new PC boards The two 2 boards you have just removed will be replaced with three 3 new printed circuit boards The PC 206 board will be replaced by the PC 327 Analog Board The PC 280 board will be replaced by the PC 322 Mother Board and the PC 323 Microprocessor Board The PC 322 and the PC 323 will arrive attached to one another and they will be installed as a single unit Installing the PC 327 Analog Board 1 Remove the new PC 327 board from its shipping container paying particular attention to prevention of electrostatic discharge damage 2 Place the new board on top of the DH 200s with the connector pins on the same end as the wiring harness Rout
9. ters Module Disassembly The following procedure should be used to disassemble your model 9016 prior to this upgrade 1 Place the scanner with its external connectors facing up With one hand holding the module housing remove all screws securing the top plate to the module housing These are located around the perimeter of the top panel of the module housing The 9016 uses twelve 12 Phillips head screws around the top plate outside perimeter See Figure 3 next page Use caution not to slip and scratch the top plate 3 www PressureSystems com Pressure Systems Inc 9016 Upgrade Instructions Remove 12 perimeter Phillips head screws REMOVE ONLY THE 12 a PERIMETER SA SCREWS w O a o wo o RUN REF CAL sue PURGE REF re ee Figure 3 9016 Top Plate 2 When all screws have been removed gently lift the top panel and attached electronics up and out of the housing All components of the pressure scanner are attached to the top plate and will lift out of the module housing when the top plate is removed See Figure 4 next page In some cases it may be easier to hold the top plate and turn the module over lifting the housing off the top panel If the Viton gasket is loose tack it down with 495 LocTite super bonder Loctite Corp USA or other suitable adhesive capable of adhering to the gasket material and to the aluminum case www PressureSystems com Pressure Syste
Download Pdf Manuals
Related Search