MTP 15HD RS Series • Setup Guide
Contents
1. 81 3 3511 7656 FAX Inside China Only 971 4 2991800 82 2 3444 1575 FAX 1 714 491 1500 1 919 850 1000 31 33 453 4040 65 6383 4400 971 4 2991880 FAX 91 80 3055 3777 1 714 491 1517 FAX 1 919 850 1001 FAX 31 33 453 4050 FAX 65 6383 4664 FAX 86 21 3760 1568 91 80 3055 3737 86 21 3760 1566 FAX FAX 68 925 50 Rev B 2013 Extron Electronics All rights reserved WWw extron com 01 132. OF Aso F 7S 3 S y Extron Electronics INTERFACING SWITCHING AND CONTROL x 9 se urio MTP 15HD RS Series Setup Guide This card provides quick start instructions for an experienced installer to set up and operate any of the MTP VGA video and RS 232 transmission systems P Unjumpered for Pre installation RS 232 Jumper Onewa Deau The receiver s RS 232 circuits are factory set to be one way transmitter to receiver If the system has only one receiver jumper JMP 1 on the main board can be set for two way communication as shown at right bi Y Installation Jumpered for Step 1 Mounting Two way Turn off or disconnect all equipment power sources and mount the MTP transmitter and up to eight receivers as required Step 2 Transmitter Inputs e Connect a computer VGA video source to the Input connector Connect a VGA monitor to the Monitor connector e Plug an RS 232 device into the RS 232 port Wire the connector as shown below Connected Receive H Ol 4a MTP Pins RS 232 Transmit ols Rx Pi 12345678 Device Pins Grun H QJ S Gnd Ins il Step 3 TP Cables Between Units e Terminate a TP cable as shown at right Connect it between the transmitter s Output port and the receiver s Input port both ends must match NOTE ifthe unit is labeled C7 only CAT 7 cable should be used Insert Twisted air Wires NOTE If you are using Enhanced Skew Free A V cable us
3. asured with test equipment or by viewing a crosshatch test pattern The SEQ receivers have built in skew compensation capabilities Adjust the equalization as follows A Zero the skew delay for red green and blue by using a small screwdriver to press and hold the Select button for 3 seconds When the Red Green and Blue LEDs all go out release the Select button B Use UTP cable test equipment or examine the displayed image to determine which video signal red green or blue E is shifted furthest to the right CORED C Select the furthest left video signal by using a small screwdriver to press and release the Select button until the LED One for the left shifted color Red Green or Blue lights D Slowly rotate the Adjust control clockwise until the selected color is properly converged E Ifthe remaining colors are left shifted repeat steps C and D A Rack Mounted Y P C Extron MTP T 15HD RS PCale isplay RGBHV D RS 232 Bare Wa MTP RL 15HD RS SEQ trcabie MTP RL 15HD RS SEQ Figure 1 Example of a Typical MTP 15HD RS Application Extron Headquarters Extron Europe Extron Asia Extron Japan Extron China Extron Extron Korea Extron India 800 633 9876 Inside USA Canada Only 800 3987 6673 800 7339 8766 4000 EXTRON Middle East 1800 3070 3777 Inside Europe Only Inside Asia Only 81 3 3511 7655 4000 398766 82 2 3444 1571 Inside India Only Extron USA West Extron USA East
4. e the TIA EIA T568A standard only MONITOR T568A T568B Wire Color Wire Color White green White orange Green Orange White orange White green Blue Blue White blue White blue Orange Green White brown White brown Brown Brown Ses Ges e For daisy chaining connect up to eight TP cables between a receiver s Buffered Output port and a daisy chained receiver s Input port Step 4 Receiver Outputs e Connect a VGA monitor to the Output connector e Plug an RS 232 device into the RS 232 port Wire the connector as shown in step 2 above shih Step 5 Receiver DIP Switches V SYNC C SYNC VIDEO END UNIT e H Sync and V Sync switches Set these switches up for positive sync or down for negative sync e Composite Sync SOG and Video switches Set these switches as shown in the following table to output the indicated format SOG Hsync s ECI o LO coo a aL L Output Format C Sync SOG RGBHV RGBS RGsB Component S Video Composite NOTE Input video format must match e End Unit switch Set this switch up if either of the following is true e The receiver being configured is the only receiver connected to the transmitter e The receiver being configured is the last receiver in a daisy chained system MTP 15HD RS Series Setup Guide Step 6 Power Panel Wire the 2 pole captive screw connectors for the included external 12 VDC po
5. wer supplies see image a nee fe on the right Plug them into all units Grounding guidelines Extron MTP 15HD RS products can be adversely affected by electrostatic discharge ESD if they are not grounded correctly To prevent malfunctions or product damage an experienced installer can correctly ground an Extron MTP 15HD RS product in either of two ways ee K ower Supply e Ground the power input port Insert one end of the grounding wire to the negative or ground pin on the power input connector see image on the right Tie the other end of the wire to an earth ground e Ground the chassis Use a connector hex nut as shown in image on the right Tie the other end of the wire to an earth ground If you have any questions about how to ground a product in a specific application contact an Extron technical support specialist Step 7 Pre Peak Peaking and Level e Transmitter Pre Peak switch View the image and set the Pre Peaking switch for the best image quality to correct for long cable runs of the entire system including all daisy chained receivers e Receiver Peaking control View the image and adjust the Peaking control for the best image Minimum setting RGB full counterclockwise is zero peaking LEVEL PEAKING e Receiver Level control View the image and adjust the Level control for the best brightness level Step 8 Skew Compensation SEQ Receivers Pair skew can be me
Download Pdf Manuals
Related Search