MC524 Monitor Interface Installation Manual
Contents
1. Crk Designator 24 X 32 High Low Gnd 1 B031 Solo L A H R 2 B032 Solo R B J 3 TL1 Talk 1 C K T 4 TL2 Talk 2 D L U 5 TL3 Listen 1 E M V 6 TL4 Listen 2 F N 7 115 Listen 3 X AE AM 8 TL6 Listen 4 Y AF AN 9 BO3 CR main L 2 10 BO4 CR main C AA AJ AR 11 5 5 12 BO6 Cntrl Rm SI AC AL AT 13 BO7 Cntrl Rm Sr BJ BS BY 14 Bos CR main B BK BT BZ 15 Bog CR main Li BL BU CA 16 BO10 CR main Ri BM BV CB 17 BO13 CR Alt 1 L BN BW CC 18 BO14 CR Alt 1 C BP BX CD 19 BO15 CR Alt 1 R CF CN Cw 20 BO16 CR Alt 1 SI CH CP CX 21 BO29 CR Alt 1 Sr CJ CR 22 BO30 CR Alt 1 B CK cs CZ 23 BO1 CR Alt 2 L CL CT DA 24 BO2 CR Alt 2 R CM CU BD 0 2 gt 60 ey E a ay 9 Tes gt 2 se Figure 9 Elco 90 Connector 20 Euphonix MC524 Monitor Interface Operation Manual Table 10 Out 3 DB 25 Pinout Crk Designator 24 X 32 High Low Gnd 1 T1 24 12 25 2 T2 10 23 11 3 L1 21 9 22 4 L2 7 20 8 5 L3 18 6 19 6 L4 4 17 5 7 Solo L 15 3 16 8 Solo R 1 14 2 3026569900000 650263026 6909 9029 9 2 Figure 10 DB 25 Connector 21 Euphonix MC524 Monitor Interface Operation Manual Optional Configurations Monitor2. IP MC524 Monitor Interface Installation Manual Document Revision A Part Number 840 11311 01 Release Date August 2010 MC524 74 Dt MONITOR A B C D SPEAKERS Euphonix is Avid Learn more at www avid com Regulatory and Safety Notices Warnings and Cautions AN Never install equipment if it appears damaged Disconnect the power cord before servicing unit Only perform the services explicitly described in this document For services or procedures not outlined in this document speak with authorized Avid service personnel Follow all warnings and cautions in the procedures Operate the device within its marked electrical ratings and product usage instructions If you need to replace a battery in an Avid hardware unit be sure to use the correct battery type There might be a risk of explosion if a battery is replaced by an incorrect type Dispose of used batteries according to the manufacturer s instructions FCC Notice Part 15 of the Federal Communication Commission Rules and Regulations has established Radio Frequency RF emission limits to provide an interference free radio frequency spectrum Many electronic devices produce RF energy incidental to their intended purpose These rules place electronic equipment into two classes A and B depending on the intended use Class A devices are t
3. W J aa OD is Control from Digital lt 8 male XLR to DB 25 Interface Pilot 6 2 TB pre out 4 Listen pre out 2 Solo out 2 Solo out TB1 returns to 2 Talk pre core for slate 8 MonA 4 Listen pre out 2 MonB 1 male Elco 90 to 8 CR Main out 2 MonC 2 male Elco 38 6 CR Alt 1 out 2 MonD 2 CR Alt 2 out C D B SER D Connectors and pins provided Connectors and pins provided Ly Upper 37 48 Upper 25 36 Lower 37 48 Lower 25 36 Upper 13 24 Upper 1 12 Lower 13 24 Lower 1 12 c o o 3 C E Figure 12 Monitor Output Patch Configuration 23 Euphonix MC524 Monitor Interface Operation Manual Monitor Insert Patch recommended locations Digital Core 2 1 3 i MA703 o G F vv MC524 J ee E F Monitor Output Patch A Machine Room Bj Control Room Use relative locations to determine cable lengths Figure 13 Monitor Insert Patch Cable Diagram Patchbay cables pins and connectors are ordered separately as required Table 12 Monitor Insert Patch Cable Specification Part Qty Description Part Length E 3 TB LB Mic Bus one male Elco 38 lt gt 12 female XLR 030 06919 01 2m MC524 Patch Connect 9 one male Elco 90 lt gt two male
4. Je E Control from Digital lt 8 male XLR to DB 25 Interface Pilot 2 TB pre out 4 Listen pre out 6 s to core for slate 22 S01 oUt 2 Talk pre out 4 Listen pre out 8 CR Main out 2 MonC 6 CR Alt 1 out 2 MonD 1 male Elco 90 lt gt 2 CRAIt 2 out 2 male Elco 38 Upper 37 48 Upper 25 36 Lower 37 48 Lower 25 36 Upper 13 24 Upper 1 12 Lower 13 24 Lower 1 12 C f yw fog 5 cem f 2 559 Ofce e o o De USER 5 DE USER 8 USER 8 Diz USER 2 J 4 PE Monitor Output Patch Figure 14 Monitor Insert Patch Configuration 25 Euphonix MC524 Monitor Interface Operation Manual Table 13 Tie Line Patch Elco 38 Pinout Connector Pair Number Signal Name Channel 1 13 25 37 Input Output Channel 2 14 26 38 Input Output Channel 3 15 27 39 Input Output Channel 4 16 28 40 Input Output Channel 5 17 29 41 Input Output Channel 6 18 30 42 Input Output Channel 7 19 31 43 Input Output Channel 8 20 32 44 Input Output Channel 9 21 33 45 Input Output Channel 10 22 34 46 Input Output Channel 11 23 35 47 Channel 12 24 36 48 Input Output Figure 15 Rear View of Elco Male 38 pin Connector Insert pins from this side Connector Specifications 38 pin male w hood El
5. 11 L13 Mon A R AB AK AS 12 L14 Mon A 51 AC AL AT 13 L15 Mon A Sr BJ BS BY 14 L16 Mon A B BK BT BZ 15 L17 Mon A Li BL BU CA 16 L18 Mon A Ri BM BV CB 17 L19 Mon B L BN BW CC 18 L20 Mon B R BP BX CD 19 L21 Mon C L CF CN Cw 20 L22 Mon C R CH CP CX 21 L23 Mon D L CJ CR 22 124 CK cs CZ 23 L1 Solo L CL CT DA 24 L2 Solo R CM CU BD Figure 7 Elco 90 Connector 18 Euphonix MC524 Monitor Interface Operation Manual Table 8 Out 1 Elco 90 Pinout Crk Designator 24 32 High Low Gnd 1 BO11 Mon A L A H R 2 BO12 Mon A C B J S 3 BO17 Mon A R C K T 4 BO18 Mon A 51 D L U 5 BO19 Mon A Sr E M V 6 BO20 Mon A B F 7 BO21 Mon A Li X AE AM 8 BO22 Mon A Ri Y AF AN 9 BO23 Mon B L 7 10 BO24 Mon B R AA AJ AR 11 25 Mon C L AB AK AS 12 BO26 Mon C R AC AL AT 13 BO27 Mon D L BJ BS BY 14 BO28 Mon D R BK BT BZ 15 BL BU CA 16 BM BV CB 17 BN BW 18 BX CD 19 CF CN Cw 20 CH CP CX 21 CJ CR 22 CK cs CZ 23 CL CT DA 24 CM CU BD Figure 8 Elco 90 Connector 19 Euphonix MC524 Monitor Interface Operation Manual Table 9 Out 2 Elco 90 Pinout
6. 2004 108 EC EN 55103 1 1996 EN 55103 2 1996 Euphonix is Avid Learn more at www avid com LED Safety Notices Class 1 LED Product Avid hardware might contain LED or Laser devices for communication use These devices are compliant with the requirements for Class 1 LED and Laser Products and are safe in the intended use In normal operation the output of these laser devices does not exceed the exposure limit of the eye and cannot cause harm Standard to which conformity is declared IEC 60825 1 Optical connections are located on the rear panel and are typically labeled Optical or SPDIF ADAT The exact location of optical connections is identified more clearly elsewhere in the documentation for the Avid hardware device Use of controls and or adjustments or the performance of procedures other than those specified herein and elsewhere in documentation for the Avid hardware might result in hazardous radiation exposure Euphonix is Avid Learn more at www avid com Disposal of Waste Equipment by Users in the European Union of with other waste Instead it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that pr
7. Output Patch recommended locations Digital Core I A Machine Room Bj Control Room MA703 Use relative locations to determine cable lengths 1 5 524 Jl EE en Fr E Figure 11 Monitor Output Patch Cable Diagram Patchbay cables pins and connectors are ordered separately as required Table 11 Monitor Output Patch Cable Specifications Part Qty Description Part Length MC524 Patch Connect 2 one male Elco 90 lt gt two male Elco 38 D 1 Tie Line Patch 950 03770 01 NA 4 Elco 38 Pin Connector w hood 100 02099 00 NA F 160 Elco Crimp Pins Supplied with standard configuration 100 02100 00 2m 22 Euphonix MC524 Monitor Interface Operation Manual DIGITAL ANALOG UTPUTS OUTPUTS IN cy AES EBU Sync In J from Studio Hub 12 female XLR to 1 Elco 38 4 Listen and 2 Talk Mic inputs 4 24 female XLR to 1 male Elco 90 Monitor bus outs from MA703 8 Control Room 8 MonA 2 Mon B 2 MonC 2 MonD 2 Solo TB LB SOLO TB IB X e 524 iu MEE NECS mE S iri our Soto BUSES
8. Patch Cable Diagram 24 Monitor Insert 25 Rear View of Elco Male 38 pin Connector Insert pins from this side 26 vi Euphonix MC524 Monitor Interface Operation Manual 10 11 12 13 List of Tables MCS 24 Performance Specifications 11 MC524 Environmental and Power Specifications 12 METT DERN s peserien 12 Upper and Lower Board Jumper Mappings 13 MC524 Standard Cable Specification visste 15 Jnl Elco 38 PINOUT e 17 Jn 2 Elco 90 PINOUT RE ERN DE 18 1 Elco EEE TEE 19 Out 2 Elco 90 PINOUT 20 Out PINOUT a 21 Monitor Output Patch Cable Specifications sse 22 Monitor Insert Patch Cable Specification 24 Tie Line Patch Elco 38 Pinout re 26 vii Euphonix 524 Monitor Interface Operation Manual Overview The MC524 Monitor Interface centralizes control room monitor and communication signals in one box and places them under remote control by the system operator The 524 is a digitally controlled analog signal router and level control device with a built in Talk Back microphone circuit in a 2RU enclosure The MC524 receives the 22 monitor busses and two solo b
9. Section We recommend installing the MC524 in the Control Room Euphonix MC524 Monitor Interface Operation Manual Front Panel MONITOR COMMS INTERFACE nimi _ 524 Figure 1 MC524 Front Panel Power Switch The power switch turns the unit on off Since the MC524 is digitally controlled via software the power switch is the only front panel control Euphonix 524 Monitor Interface Operation Manual TB LB B LB O CONTROL ROOM SPEAKERS 18 5010 EDEN 1 PREAMP CONTR MONITOR AED SPEARERS SOLO BUSES Ni MONITOR BUSES IN THE USA SOLO BUSES 1 ouT2 IN2 Figure 2 MC524 Rear Panel In 1 38 pin Elco Talk Back Listen Back and Mic inputs This connector receives four stereo listen channels and two stereo talk mic inputs All signals input at this port can be level boosted or attenuated In standard patch configuration input cable fans out to 12 XLR females In 2 90 pin Elco Control Room Busses Monitor A B C D and Solo busses inputs This connector receives eight Monitor A channels and two each channels for Monitor B C D Signals input at this port can only be level attenuated In standard configuration these signals are fed from the AM713 converter Out 1 90 pin Elco Monitor A B C D Speaker outputs This connector outputs eight Control Room channels eight Monitor A channels and two each channels for M
10. 5010 TB LB Ce 9 524 B Gr samt rooms MADE IN THE USA 5010 BUSES 1 our2 IN2 CONTROL o o 9 O Control from Digital 3 8xXLRM to DB25 Interface Pilot 6 8 MonA 2 Solo out 2 TB pre out 2 MonB 2 Talk pre out 4 Listen pre out 2 MonC 4 Listen pre out 2 Solo out 2 MonD 8 CR Main out TB1 returns to 6 CR Alt 1 out core for slate 2 CR Alt 2 out 7 8 Connectors and pins provided Figure 5 MC524 Standard Configuration 16 Euphonix MC524 Monitor Interface Operation Manual Input Output Connections Table 6 In 1 Elco 38 Pinout Crk Designator 24 X 32 High Low Gnd 1 M1 Talk 1 L 2 M2 Talk 2 B M 3 M3 Listen 1 H N 4 M4 Listen 2 D J P 5 M5 Listen 3 DD JJ PP 6 M6 Listen 4 EE KK RR 7 FF LL 55 8 HH MM TT 9 R 5 V 10 T U W 11 X 7 12 59 90 9 Jer BS 5990 Figure 6 Elco 38 Connector 17 Euphonix MC524 Monitor Interface Operation Manual Table 7 In 2 Elco 90 Pinout Crk Designator 24 X 32 High Low Gnd 1 L3 Cntrl Rm L A H R 2 L4 Cntrl Rm C B J S 3 L5 Cntrl Rm R C K T 4 L6 Cntrl Rm SI D L U 5 L7 Cntrl Rm Sr E M V 6 L8 Cntrl Rm B F Ww 7 L9 Cntrl Rm Li X AE AM 8 L10 Cntrl Rm Ri Y AF AN 9 L11 Mon A L 2 10 L12 Mon A C AA AJ AR
11. Elco 38 eee De MC524 Patch Connect G 1 one male Elco 38 lt gt one male Elco 38 ean H 1 Tie Line Patch 950 03770 01 NA 24 Euphonix MC524 Monitor Interface Operation Manual f MA703 DIGITAL ANALOG UTPUTS OUTPUTS MADI IN O X in from Core 2 12 female XLR to 1 male Elco 38 AES EBU Sync In Monitor bus outs from MA703 from Studio Hub D L JC R 5 548 u CIR bi gt 112 5 6 7 8 9 10 11 12 13 14X15 16X17 18K 19 20K 211 22 23 24 25126 2728 29 30 31 32 333435 36 37 38 139 140 41142143 144451 46 47 148 gt Monitor Insert Patch Y Y cy Upper 37 48 Upper 25 36 Lower 37 48 Lower 25 36 Upper 13 24 Upper 1 12 Lower 13 24 Lower 1 12 c 2 2 gt 8 Control Room 12 female XLR lt gt 1 male Elco 90 lt gt gt 8 Mon 1 Elco 38 zm uet 2 male Elco 38 F 2 MonB 4 Listen and G 2 MonC 2 Talk Mic inputs 1 male Elco 38 2 MonD 1 male Elco 38 2 Solo fF AS DA UNIO MC524 scimus TRIB peen wi BUSES 6 AE ban SOLO auses o 1 our2 IN2 N EET DI A conTROL EN
12. ave Maximum Input Voltages 16 VDC 25 VAC common mode 50 VAC differential Input impedance 10 10 each leg 20 Hz 20 kHz CMRR gt 40 dB 50 dB typical 20 Hz 20 kHz Talk Back And Listen Mic Inputs Description T1 T2 L1 L4 Electronically balanced transformerless differential input with automatic level optimization Gain AGC circuit optimizes front end gain to produce approx 8 dBU signal this is variable from 8 to 64 dBU at the monitor outputs Maximum Input Level Before Clipping 10 dBU sine wave Maximum Input Voltages 50 VDC 2 5 VAC common mode 5 VAC differential Phantom Power 48 V available link selectable on PCB Frequency Response Attenuated LF and HF response 3 dB at 200 Hz and 10 kHz Monitor Outputs Description Electronically balanced and floating differential output Maximum Output Level 28 dBU sine wave Output Impedance 100 10 balanced or unbalanced 20 Hz 20 kHz DC Offset lt 5 mV with respect to chassis GND Full Signal Path Frequency Response Main Input To Monitor Output 0 0 4 dB 20 Hz 20 kHz ref 1 kHz Signal Breakthrough with Full Cut lt 110 dB 20 Hz 20 kHz Distortion lt 0 005 20 Hz 20 kHz 15 dBU output level Crosstalk lt 100 dB at 1 kHz lt 90 dB at 20 kHz Output Noise lt 90 dBU RMS unweighte
13. co P N 00 8016 038000 519 Euphonix P N 100 02099 Use crimp pins Elco P N 60 8017 03 1300 339 Euphonix P N 100 02100 26
14. d gt 117 dB of dynamic range at unity gain 11 Euphonix MC524 Monitor Interface Operation Manual Table 2 MC524 Environmental and Power Specifications Operating Temperature 5 35 Power Requirements 100 240 VAC 50 60Hz Power Consumption 1A Table 3 MC524 Physical Dimensions 3 5 inches 19 inches 18 6 inches 17 5 Leave about six inches behind the MC524 for cable connections 12 Euphonix MC524 Monitor Interface Operation Manual Authorized Service Personnel Only Phantom Power 48 V Jumper Settings Phantom power is enabled by fitting the link to short pins 1 and 2 If not required 1 using a dynamic mic then it should be set to short pins 2 and 3 Pin 1 position can be ascertained by looking for the square pad on the solder side TUS ERNI Ji 2 J3 Figure 3 Pins to set Phantom Power Note that the standard Talk Back mic on the console wired to T1 is a condenser type which requires phantom power Table 4 shows the mapping of the jumpers Table 4 Upper and Lower Board Jumper Mappings Talkback 1 T1 Listen 2 L2 Talkback 2 T2 Listen 3 L3 Listen 1 L1 Listen 4 L4 13 Euphonix 524 Monitor Interface Operation Manual User Reference Standard Configuration Digital Core recommended locations A Machine Room Bi Control Room Use relative locations t
15. equipment Cables Connections to Avid hardware must be made with shielded cables with metallic RFI EMI connector hoods in order to maintain compliance with FCC Rules and Regulations PRODUCTS WITH MULTIPLE POWER INPUTS WARNING Each power input is intended to be connected to a separate branch circuit Risk of high leakage exists if multiple inputs are connected to a single source and protective earth is not present A QUALIFIED SERVICE PERSON shall verify that each socket outlet from which the equipment is to be powered provides a connection to the building protective earth If any do not provide this connection the QUALIFIED SERVICE PERSON shall arrange for the installation of a PROTECTIVE EARTHING CONDUCTOR from the separate protective earthing terminal to the protective earth wire in the building Canadian ICES 003 Class A Equipment This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la classe A respect toutes les exigences du R glement sur le mat riel brouilleur du Canada Euphonix is Avid Learn more at www avid com European Union Declaration of Conformity Declaration of conformity Konformitatserklarung D claration de conformit Declaraci n de Confomidad Verklaring de overeenstemming Dichiarazione di conformit We Wir Nous WIJ Noi Avid Technology 1925 Andover Street Tewksbury MA 01876 USA Europea
16. hose that may be expected to be installed in a business or commercial environment Class B devices are those that may be expected to be installed in home or residential environment The FCC requires devices in both classes to be labeled with the interference likelihood and additional operating instructions The rating label on the equipment will show which class the product is A or B Class A product will not have an FCC logo Class B equipment will have an FCC logo The information statements differ on the two classes Class A Equipment This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at personal expense Euphonix is Avid Learn more at www avid com Modifications The FCC requires the user to be notified that any changes or modifications made to Avid hardware that are not expressly approved by Avid Technology may void the user s authority to operate the
17. n Contact Nearest Avid Sales and Service Office or Avid Technology International B V Sandyford Industrial Estate Unit 38 Carmanhall Road Dublin 18 Ireland declare under our sole responsibility that the product erkl ren in alleniniger Verantwortung daf dieses Produkt d clarons sous notre seule responsabilit que le produit Euphonix is Avid Learn more at www avid com declaramos bajo nuestra sola responsabilidad que producto verklaren onder onze verantwoordelijkheid dat het product dichiariamo sotto nostra unica responsabilita che il prodotto Product Name s Monitor Interface Model Number s MC524 Product Options This declaration covers all options for the above product s to which this declaration relates is in conformity with the following standard s or other normative documents auf das sich diese Erkl rung bezieht mit der den folgenden Norm en oder Richtlinie n bereinstimmt auquel se r f re cette d claration est conforme la aux norme s ou au x document s normatif s al que se refiere esta declaraci n es conforme a la s norma s u otro s documento s normativo s waarnaar deze verklaring verwijst aan de volende norm en of richtlijn en beantwoordt a cui si riferisce questa dichiarazione conforme alla e seguente i norma o documento i normativo i The requirements of the European Council Safety Directive 2006 95 EC EN 60065 2002 A1 2006 EMC Directive
18. o determine cable lengths Figure 4 MC524 Standard Cable Diagram The standard lengths specified in Table 5 are supplied so the monitor interface can be located in the control room Custom lengths are available and cable kits must be ordered separately 14 Euphonix MC524 Monitor Interface Operation Manual Table 5 MC524 Standard Cable Specification Description Accessory cable kits by special order 10M Part 936 07084 01 20M Part 936 07156 01 Output RG59 75 Q coax 032 07230 00 032 07306 00 AES EBU Sync 030 07085 01 030 07153 01 one male XLR lt gt one female XLR TCC Control from 253i Interface Pilot 030 06983 01 030 06985 01 TB LB Mic one male Elco 38 lt gt 12 female XLR CR Mon Solo Bus one male Elco 90 lt gt 24 female XLR 030 06919 01 030 07225 01 TB and LB Mic Pre Out one DB 25 lt gt eight male XLR 032 07038 00 Elco 90 pin Connector w hood 100 07470 00 Elco Crimp Pins 100 02100 00 15 Euphonix MC524 Monitor Interface Operation Manual lt MA703 DIGITAL ANALOG OUTPUTS in from Core 24XLRFto 1xEM90 AES EBU Sync In Monitor bus outs from Studio Hub from MA703 5 8 Control Room 8 MonA 12XLRF lt gt 1xEM38 ya e 4 Listen amp 4 2 Talk Mic inputs 2 MonD 2 Solo O 78 18
19. onitor B C D and Solo The output cable fans out to two 38 pin Elco connectors for the Eu phonix Patchbay Out 2 90 pin Elco This connector outputs eight Control Room Main channels six Control Room Alt 1 channels two Control Room Alt 2 channels four Listen pre two talk pre and two Solo channels The output cable fans out to two 38 pin Elco connectors for the Euphonix Patchbay Out 3 DB 25 female This connector outputs four Listen pre two Talk Back pre and two Solo channels eight Monitor A channels and two channels each for Monitor B C D and Solo The output cable fans out to eight male XLR connectors Control DB 15 Input for digital control signal from Digital Pilot Signal format is Euphonix TCC bi directional serial protocol All patching switching and gain controls are communicated via this connection as well as MC524 IP address AC Line In IEC and Fuse Tray The power connector accepts standard IEC power cords 110 220 or 240 VAC 50 60 Hz can be applied at this connector 10 Euphonix MC524 Monitor Interface Operation Manual Specifications Table 1 MC524 Performance Specifications Main Inputs Solo CR 7 Mon A B C D Description Electronically balanced transformerless differential input Gain Variable from 0 dB unity to 72 dB Optimum Input Levels Set to 0 dBFS 27 dBU Designed to be fed from Euphonix MA703 DAC Maximum Input Level Before Clipping 28 dBU sine w
20. otects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city recycling office or the dealer from whom you purchased the product This symbol the product or its packaging indicates that this product must not be disposed Rack mount Requirements The following rack mount requirements are listed below Elevated Operating Ambient If installed in a closed or multi unit rack assembly the operating ambient temperature of the rack environment might be greater than room ambient Therefore consider installing the equipment in an environment compatible with the maximum ambient temperature Tma specified by the manufacturer Reduced Air Flow Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised Do not block vents Mechanical Loading Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading Circuit Overloading Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring Appropriate consideration of equipment nameplate ratings should be used when addressing this concern Reliable earthing Reliable earthing of rack mounted equipmen
21. t should be maintained Particular attention should be given to supply connections other than direct connections to the branch circuit for example use of power strips Euphonix is Avid Learn more at www avid com Lithium Battery Replacement If a battery is supplied in this Avid product it must only be replaced by qualified personnel Contact Avid Customer Support for assistance WARNING Danger of explosion if battery is incorrectly replaced Replace with only the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions ADVARSEL Lithiumbatteri Eksplosionsfare ved fejlagtig handtering Udskiftning ma kun ske med batteri af samme fabrikat og type Lev r det brugte batteri tilbage til leverand ren ADVARSEL Lithiumbatteri Eksplosjonsfare Ved utskifting benyttes kun batteri som anbefalt apparatfabrikanten Brukt batteri returneres apparatleverandgren VARNING Explosionsfara vid felaktigt batteribyte Anvand samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren Kassera anvant batteri enligt fabrikantens instruktion VAROITUS Paristo voi r j ht jos se on virheellisesti asennettu Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin Havita k ytetty paristo valmistajan ohjeiden mukaisesti Euphonix is Avid Learn more at www avid com Euphonix MC524 Monitor Interface Opera
22. tion Manual Table of Contents List of Figures vesen vi List of Tables P vii 8 Features et X 8 tear 8 Line Y amp Li e amp Applications amp Front RD 9 Xd 10 SBOCLHTIGd EE 11 Phantom Power 48 V Jumper Settings sss 13 User CTL STAGE oon vito 14 Standard Configuration 14 Input Output Connections i5 dasiasahcesnvstncensdessucasantasessdasvecauesabdinennaneuseanans 17 Optional Configurations oo caesi odd DEP EGER CD UR PME PO Li QU D GNE kne 22 Euphonix 524 Monitor Interface Operation Manual 10 11 12 13 14 15 List of Figures Me TL 9 MC3524 Rear 10 Pins 00 set Phantom OE ME 13 524 Standard Cable DISPESEBL eee 14 524 Standard Configuration 16 Elco 38 Connector 5 17 EET 18 FICO OM Jaer 19 Elco 90 Comme 20 DE 5 Ce se 21 Monitor Output Patch Cable Diagram 25 cscccaccssdcsssssaccosastncsutdedncvensasihenssiasadeuasesaivtastaccnsinsse 22 Monitor Output Patch Configuration 23 Monitor Insert
23. usses from the System 5 monitor matrix output and provides a control room output to three speaker sets four SLS Cue monitor outputs as well as post preamp talk and listen mic outputs The 5 2531 Interface Pilot digitally controls the MC524 over a 15 pin control cable with a maximum length 100 m The system operator can control all MC524 parameters from the System 5 control surface There is only one MC524 in a System 5 configuration Features Mic Inputs Mic level inputs are provided for four Listen and two Talk mics on a 38 pin Elco con nector An analog gain stage provides boost or attenuation for mic level signals Talk Back mic inputs include phantom power and a compressor Line Inputs There are 24 line level inputs for Control Room feeds Monitor and Solo Line level inputs have attenuation only Line Outputs Line outputs are on 90 pin Elco connectors for eight Monitor A up to 7 1 monitoring two each for Monitor B D eight Control Room Main up to 7 1 monitoring six Con trol Room Alt 1 up to 5 1 monitoring two Control Room Alt 2 four Listen preamp two Talk preamp out and two Solo outputs cabling is provided from the digital input to the final user connections of the output patchbay See the cabling diagrams in the User Reference section Applications The 524 allows the System 5 engineer to adjust all Control Room communications Level Control Cut Dim and speaker selection from the console Center
Download Pdf Manuals
Related Search