Do Guide: DM-RMC-200-C
Contents
1. CRESTRON GUIDE DM RMC 200 C DigitalMedia 8G Receiver and Room Controller 200 DO Install the Device The Crestron DM RMC 200 C mounts into a 2 gang electrical box using the included support bracket The support bracket provides a holder for the included power pack Mounting the Device into an Electrical Box To mount the device into an electrical box do the following 1 Using the four included 6 32 x 3 4 combo truss head screws attach the included support bracket to the electrical box SS 2 Ground the DM RMC 200 C and attach the proper cables to the back of the unit Amplified Stereo Ground Audio Output To Relay Software From DM Switcher Controllable Programmable Transmitter or Devices Digital Input Other DM Device or from HDBaseT Device DO Check the Box QTY PRODUCT Connector 2 Pin N Connector 2 Pin Connector 4 Pin Connector 5 Pin Power Cord 5 10 1 78 m Power Pack 24 Vdc 2 5 A 100 240 Vac Screw 6 32 x 1 2 Pan Head Phillips Screw 6 32 x 1 Pan Head Phillips Screw 6 32 x 3 4 Truss Head Combo Bracket Support Tie Wrap Cable Tie 15 1 2 x 1 Not Included Cables OEE e e Ree ES Black Black Black PART NUM 2003574 2003582 2003576 2003577 2042043 2041865 2007238 2007250 2009211 2042429 2013608 3 Using the four included 6 32 x 1 Phillips pan head screws attach the DM RMC 200 C to t2. ency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation DOC 7549A 2042263 05 15 Specifications subject to change without notice CRESTRON GUIDE
3. esponsible for compliance could void the user s authority to operate the equipment The specific patents that cover Crestron products are listed at patents crestron com The product warranty can be found at www crestron com warranty Crestron the Crestron logo Crestron Toolbox DigitalMedia DigitalMedia 8G and DM are either trademarks or registered trademarks of Crestron Electronics Inc in the United States and or other countries HDBaseT and the HDBaseT Alliance logo are either trademarks or registered trademarks of the HDBaseT Alliance in the United States and or other countries HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and or other countries Other trademarks registered trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products Crestron disclaims any proprietary interest in the marks and names of others Crestron is not responsible for errors in typography or photography This document was written by the Technical Publications department at Crestron 2015 Crestron Electronics Inc NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequ
4. he support bracket Inserting the Power Pack into the Power Pack Holder To insert the power pack into the power pack holder do the following 1 Position the power pack between the left and right flanges and behind the bottom flange of the power pack holder 2 Using the included 6 32 x 1 2 Phillips pan head screw thread the screw through the hole in the top flange of the power pack holder to hold the power pack in place 3 Using one of the included tie wraps thread the tie wrap through the hole in the right flange of the power pack holder and then fasten the tie wrap to the power pack cable Tie Wrap Installation of the power pack in the holder appears as shown below DO Make Additional Connections to the Device Make additional connections as appropriate for the application Front Panel Connections Rear Panel Connections AUDIO OUT R L LAN AUDIO OUT R L LINE 10BASE T SPEAKER Stereo Unbalanced 100BASE TX Amplified Stereo Line Level Ethernet to Local Audio Output Audio Output Network Device 24V 2 5A MAX i Cd From Power Pack Included NOTE Connection to the power pack is not required when PoDM is used to power the device DO Set the IP Address The conf
5. iguration of the receiver within the DigitalMedia 8G system determines how the IP address of the receiver is set e If the receiver connects to a DigitalMedia switcher the 1 The DM IN port is a PoDM Power over DM or PoH Power over HDBaseT PD Powered Device port To receive PODM or PoH the DM RMC 200 C HDMI OUT receiver is configured by the switcher automatically i d in i HDMI Digital COM requires a connection to a DigitalMedia switcher or other equipment that Video Audio To RS 232 e If the receiver connects to a DigitalMedia 8G transmitter has a PoDM or PoH PSE Power Sourcing Equipment port Any wiring that Output Device the receiver uses its own configuration settings By default is connected to a PoDM or PoH PSE port is for intra building use only and t DHCP Dynamic Host Configuration Protocol is enabled should not be connected to a line that runs outside of the building in which If desired you can assign the default IP address to the the PSE is located A pasna receiver by holding down the SETUP button while the unit boots up The default IP address overwrites the current 4 setting The default IP address of the DM RMC 200 C is DO Learn More DIG IN USB HID IR 192 168 1 245 To manually set a different IP address use Visit the website for additional information and the Software Fro
6. m USB To IR Crestron Toolbox latest firmware updates Programmable HID Compliant Controllable Crestron Electronics Digital Input Device Device 15 Volvo Drive Rockleigh NJ 07647 888 CRESTRON www crestron com If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help C As of the date of manufacture the product has been tested and found to comply with specifications for CE marking Mus This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc Federal Communications Commission FCC Compliance Statement s This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions s 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference i Industry Canada IC Compliance Statement that may cause undesired operation CAN ICES 3 B NMB 3 B CAUTION Changes or modifications not expressly approved by the manufacturer r
Download Pdf Manuals
Related Search