Installation Sheet
Contents
1. 1 Fan Housing amp Motor 1 Blade Arms 5 Blades 5 5 1 1 3 Adjustable Wrench Medallion Glass TCS Hand Held Control SOMNDARY 2 Flat Screwdriver 4 Wire Strippers Turn off circuit breakers and wall switch to the fan supply line leads A Piesuciton Important When using an existing outlet box be sure the box is P securely attached to the building structure and can support the full weight of the fan Failure to do so can result in serious injury or death a Downrod Mount b Angle Mount Normal Ceilings Vaulted Ceilings IMPORTANT If using the angle mount method check to make sure the ceiling angle is not steeper than 35 Angles greater than 35 will require a 45 angle adapter d 30 gt Oe ta ala T jot Jet e Check to make sure blades are at least 30 from any obstruction e Check Down rod Length to make sure blades are at least 7 above the floor Installing Mounting Brachet Support Beam J Hook S8 Outlet Box A Ceiling Bracket Screws amp Washers S3 Wood Screws S1 Prior to securing mounting bracket screw J hook S8 into ceiling outlet box as a secondary support means Secure mounting bracket 1 to the outlet box A by tightening bracket screws amp washers S3 as shown If not mounting to an outlet box use wood screws S1 and washers S3 and mount2. 5th Avenue Ceiling Fan ai FA52 Installation Instructions Instrucciones de instalaci n Instructions d installation ee Da GRAFTMADE air light sound Read and Save These Safety Precautions 1 Turn off electricity at main switch before wiring or servicing fan in order to avoid possible electrical shock All wiring must be in accordance with the National Electric Code ANSI NFPA70 1999 and local electrical codes Electrical installation should be performed by a qualified licensed electrician After making the wire connections the wires should be spread apart with the grounded conductor and the equipment grounding conductor on the one side of the outlet box and the ungrounded conductor on the other side of the outlet box The splices after being made should be turned upward and pushed carefully up into the outlet box Conductor of a fan identified as grounded conductor to be connected to grounded conductor of power supply conductor of a fan identified as ungrounded conductor to be connected to an ungrounded conductor of power supply conductor of fan identified for equipment grounding to be connected to an equipment grounding conductor Fan should not be mounted in an area where it might get wet To reduce the risk of fire electric shock or personal injury mount to outlet box marked Acceptable for Fan Support and use mounting screws provide with the outlet box The outlet box and its support must be abl
3. e to support the moving weight of the fan at least 351bs For safety and best operating results we recommend that you have a qualified electrician assemble and install your fan WARNING To reduce the risk of fire or electric shock use the fan only with solid state speed control device provided 10 To reduce the risk of personal injury do not bend the blade brackets when installing the brackets balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades 11 Net Weight The weight of the complete fan including assembly hardware is 18 74 lbs Trouble Shooting Problem A Fan Will not Start Remedies 1 Check fuse or circuit breaker and replace if necessary 2 Turn off electrical power and check all wire connectors 3 Check on off TCS and wall control selector switch See operation instructions Problem B Fan is Excessively Noisy Remedies 1 Check that all screws in fan assembly are tight and properly seated 2 Check to make sure mounting bracket is installed properly 3 Check to make sure light kit and glass are installed properly and tight 4 If wall control is used insure the wall control is not a transformer or a variable speed type Problem C Fan Wobbles Remedies 1 Check that all blades are screwed firmly into blade holders 2 Check that all blade holders are screwed firmly into motor 3 Check the weight of blades All our blades are weighed on electronic scales The wei
4. ght is marked on the reverse side of the fan blade near the motor end All of the blades should be the same weight to prevent fan from wobbling 4 A balancing kit is enclosed if needed Before Assembly Make sure that the fan voltage 120 is compatible with your own electrical 2 Screw Package Quantity S1 2 S2 S3 S4 S5 S6 S7 S8 S9 system Check to make sure that your carton contains all the parts mentioned in the parts list NOTE The box can be used as a work space to prevent any damage on the ornamental surface CAUTION Before installing choose a location for mounting the fan where the blades have at least 7 feet of clearance from all objects and floor Mount an outlet box to the ceiling or use an existing box CAUTION Do not mount fan to sheet rock or drywall type materials To insure proper support use the two 1 wood screws to secure mounting bracket to joist or beam If the location you choose does not have a suitable support beam install a 2 x 4 brace between ceiling joists to support Mer ODOTTeTOTTT TI r 1 Hardware IT Wood Screws amp Washers O Blade Screws Motor Screws Wire Connectors o Safety Bolt amp Nut J Hook Zip Tie Screws for Canopy Bracket Screws amp Washers iii o Tools you Need What You Have Parts Quantity 1 Mounting Bracket 1 2 Down Rod Assembly 1 1 Phillips Screwdriver 6 Rod Supplied Canopy Assembly 1 Flange Cover
5. ly A slot as shown in Step 12 allows you to tighten the blade assembly to the Fan Motor Screw in Halogen bulb included Twist the Glass onto Light Kit Fitter securely ON OFF HIGH MEDIUM LOW REVERSE FAN OFF Remote Control Operation Instructions For emergency shut off Controls fan motor speed To select desired speed press button once and release Controls direction of fan blades To reverse fan blades press once and release Turns fan motor speed off Press once to turn off To start motor speed again hit one of the motor speed buttons Controls no function on this fan Controls the on off and intensity for optional light kit Push and release for on off function Hold down for full range light dimming The High Medium or Low buttons may be used to start the fan motor The speed of the fan may be changed at anytime
6. securely to ceiling beam Be sure at this point to insert canopy screws S2 in bracket Downrod Assembly Locate downrod assembly 2 Loosen ball screw on black hanging ball to free lock pin Black hanging ball will slide down Remove ground screw and green ground wire Remove hanging ball from downrod and save all parts Insert fan wires through downrod Thread the downrod onto the motor housing making sure the wires don t get twisted Insert saftey bolt S7 through flange amp downrod and attach nut Tighten firmly Tighten set screw A against downrod Place Flange cover 4 over downrod assembly Place Canopy Assembly 3 over downrod 2 A WARNING Failure to completely tighten downrod as described in steps above could result in the fan loosening and possibly falling Replace hanging ball insert hanging pin through downrod and tighten set screw C in hanging ball into downrod Lift fan onto the mounting bracket 1 Turn housing until hanging ball seats itself into ball socket listen for click For added security attach safety cable from fan unit to J hook S8 in outlet box Secure by looping zip tie S9 through safety cable and J hook Tighten zip tie securely A WARNING To red
7. uce the risk of fire electric shock or personal injury mount so outlet box marked acceptable for fan support and use mounting screws provided with the outlet box Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt Wire 1 Connect fan wires to ceiling ili j ses wires white fan wire to white Black TG GY outlet wire black to black and Ba green to green VVire connectors S6 are provided for your conve nience If an additional blue wire is present then also connect the blue wire to the black wire Green Outlet Box Ground Green 2 After connections are made turn splices upward and push carefully into outlet box Separate blue and black wires on one side of the box and white and green wires on the other side There are up to four wires coming from the top of the motor including ground wire Attach canopy 3 to the mounting bracket by placing screws S2 into slot in canopy Twist clockwise to lock into place Tighten screws firmly Seat the canopy screw cover into slots and twist to lock Assemble blade arm blade and Blade Arm Medallion Assemble blade arm blade and Blade Arm Medallion Using motor screws S5 provided line up holes from the blade arm with the holes in the motor housing Tighten screws secure
Download Pdf Manuals
Related Search