Natural Gas - Royal Cozyfires
Contents
1. 2 7 Front and Frets Requirements for ventilation 2 8 Advising the customer Section 3 0 Maintenance and Servicing 3 1 Removal of debris or soot 3 2 Servicing components below the heat engine 33 Spare parts 3 4 Useful telephone numbers 2 HM82 010710 Section 1 Instructions for Use RECORD OF PURCHASE INSTALLATION Super Hot Toaster Mk4 Purchase Details Date of purchase Purchase from Address Installation Details Date of installation Installed by Registration number Telephone number Appliance Details Serial number located on rating label Product Code located on white label on outer carton It is advisable to have all the above information available if assistance is required It will aid our service department in helping you more efficiently 3 HM82 010710 IMPORTANT NOTES Super Hot Toaster Mk4 LL CAUTION THIS PACKAGE WEIGHS 15 Kgs assess the load before you move it and note any other handling information on the packaging If you think the load is beyond your safe capability DO NOT PUT YOURSELF AT RISK Seek assistance from other person s and or use appropriate handling equipment ITS YOUR BODY LOOK AFTER IT LL This appliance is for DECORATIVE PURPOSES ONLY and is manufactured to the requirements of the current issue of EN 509 LL This appliance is for use on NATURAL GAS G20 ONLY at a supply pressure of 20mbar 1mbar LL IN GREAT BRITAIN this appliance M2. front face of the fire opening Fig 14 ELLE ORARAA RRR RRRA RRRA AI AAAA ON AER RRA VAGE AAAA PP LARRABEE RARE OR LARA KERALA RR OR LAR A ee T a P ON AERA OPENING PIRR PAE EE ee Minimum hearth height 50mm Minimum hearth width 805mm Minimum hearth thickness 12 5mm o oo SAA HM82 010710 2 4 4 INSTALLING THE APPLIANCE Fitting the appliance in position Super Hot Toaster Mk4 BEFORE COMMENCING WORK TURN OFF ALL APPLIANCES THAT ARE FED BY THE METER ISOLATE THE GAS SUPPLY BY TURNING OFF AT THE METER It will be necessary to dismantle the burner unit from the firebox before installation into the opening Remove the two fixing screws on the left and right hand side of the burner Lift and pull forward Fig 15 Fig 15 i i E a Fixing Screw gt Teen a ee Fixing Screw o o E a E fo E f fe eee 2 4 4 1 INSTALLING THE APPLIANCE Connecting A restrictor elbow complete with pressure test point is fitted to the appliance to facilitate servicing The gas supply to the appliance may be from the front left hand side or as a concealed fitting from the rear left or right hand side The preferred method of connection should be from the rear left It is important to note the requirements of the current issue of BS 6891 dealing with enclosed
3. hearth area Combustible materials must not be put on or left in the hearth area nor should the coal bed be used to burn rubbish or other materials E This appliance uses fuel effect components gaskets and insulation material containing Refractory Ceramic Fibre RCF which are man made vitreous silicate fibres Excessive exposure to such material may cause temporary irritation to the eyes skin and respiratory tract Consequently it makes sense to take care when handling these articles to ensure that the release of dust is kept to a minimum LL This appliance is fitted with an ODS a spillage monitoring system which operates if the evacuation of products is interrupted i e blocked or incorrect flueing If the appliance repeatedly goes out it may indicate a problem and the installer or specialist should be consulted before further use Q The minimum temperature rating of any back panel or hearth must have a minimum fire resistance rating of CLASS 0 100 C LU If any home improvements e g double glazing are carried out after this appliance has been installed you should contact your Registered Installer and have the operation of the flue checked 1 3 LIGHTING AND EXTINGUISHING THE APPLIANCE 1 Remove the fret Fig 1 to gain access to the controls Fig 2 Fig 2 SA e Gas Control 2 Press and turn the gas control anti clockwise to the IGN
4. pipes This standard requires that when a gas pipe is fed through a wall it should be enclosed in a gas tight sleeve to protect against failure caused by movement and shall be constructed to prevent passage of gas either between the pipe and sleeve or sleeve and wall 2 4 4 2 INSTALLING THE APPLIANCE Restrictor plate A restrictor plate is supplied with the IFU kit This restrictor is for use when installing the appliance into a CLASS 1 FLUE ONLY The restrictor plate MUST NOT BE USED ON CLASS 2 FLUES The restrictor plate is fixed to the flue outlet using the two screws provided in the IFU kit Fig 16 Fig 16 11 HM82 010710 2 4 4 3 INSTALLING THE APPLIANCE Fitting the firebox in the opening Prior to fitting the firebox fit the foam seal provided It should be positioned approximately 10mm from the outside edge of the metalwork This ensures maximum flow of air through the flue There are two options to fit the firebox into the opening O lt Fixing hole Fixing hole gt OPTION 1 WALL FIXING Position the firebox in the centre of the opening Mark Fig 1 7 the holes provided in the firebox and drill plug and screw to either the base or trim support of the fire Replace the burner unit Fig 17 l o Fixing hole LEF lol Fixing hole gt o L TO A Q Two fixing holes in base of firebox OPT
5. position Keep the control fully depressed 3 Once lit keep the gas control depressed for a further 15 seconds 4 Release the gas control and check that the main burner has remained alight 5 Press and turn the gas control anti clockwise to the required setting Replace the fret controls cover 6 To turn the appliance off depress and turn the gas control clockwise from any position to the OFF position 7 In the event of the piezo ignition failing the appliance may be lit by placing a lighted taper or match at the main burner while depressing the gas control in the IGN position IMPORTANT After turning off or if the appliance goes out for any reason wait for three minutes before attempting to relight 4 HM82 010710 RE LAYING THE COAL PEBBLE BED Super Hot Toaster Mk4 metalwork There are two metal stops that prevent the support shelf from sitting on the main burner outlet Fig 3 f The support shelf is positioned on the fibre support 1 Fig 4 JW m Jin urs Fon an Ti in Metal stops The simulated front is positioned on the shelf directly in front of the support shelf Two metal stops locate the simulated front in position Fit the two front retaining brackets with the two No 8x3 8 screws supplied in the fixing pack to secure the front into position Fi
6. the two fastening nuts and washers from the rear of the burner unit Remove the stainless steel baffle and spacer plate Disconnect the formed pipe connecting the gas control and injector Unscrew the injector from the main burner Sed Unscrew the two fastening nuts and washers from the front of the burner unit N Remove the main burner Unscrew the locknut retaining the thermocouple Remove the thermocouple we Replace in reverse order 2 2 2 2 2 KSA KSA KSA SCS S 2 KSA SCS KS 2 KSA 16 HM82 010710 Super Hot Toaster Mk4 3 3 SPARE PARTS BRITISH GAS PART DESCRIPTION CROSSLEE PART No QUANTITY COUNCIL NUMBER Aeromatix Burner Natural Gas Manuf No AC03 21 1656 079M Straight Injector Manuf No 044 341 196 079M Inlet Bundy Gas Valve Manuf No 21531B 010207802931 Z Control Knob Manuf No 2263 010207802791 7 Facia Assembly HT4 painted 010208955091 _ _ Bundy Pipe Tap Injector 10 Heat Shield 002075333834 1 12 Thermocouple c w Nut Manuf No T100 927 400 13 14 FrontRetainingBracket Ci 010207533451 S O 15 Baffle Spacer Plate CSE 00207031554 o O Black Coal Bed see section 1 4 010209552201 Black Simulated Front see section 1 4 Set of Ceramic Coals see section 1 4 9 Large 9 Small Set of Ceramic Pebbles see section 1 4 9 Large 9 Small 010209240171 Magnet Manufacturer s part no N30H 42561 E01 395 Quantity depends on
7. trim option 17 HM82 010710 3 4 USEFUL TELEPHONE NUMBERS In the event that you may require service spares or technical information please contact us at Crosslee PLC Halifax West Yorkshire HX3 8DE Telephone Fax Customer Service 01422 203963 01422 204767 Service Engineer REPAIRCARE 0844 8797422 Calls cost 5p per minute from a UK BT landline Charges from mobile and other network providers may vary 18 HM82 010710
8. 0102 095 52182 SHT Mk4 NG COZYFIRE SUPER HOT TOASTER MK4 d User Installation amp Servicing Instructions This appliance is for use on NATURAL GAS G20 ONLY at a supply pressure of 20mbar Please hand this booklet to the user and advise to keep in a safe place Important Notice Before disposal of the outer packaging please enter the product code purchase and installation details in section 1 1 of this booklet 1 HM82 010710 This booklet details instructions for USER section 1 INSTALLATION section 2 amp SERVICING section 3 IMPORTANT NOTICE It is important for the safe and continued operation of this appliance that the instructions contained in this booklet are observed TABLE OF CONTENTS Section 1 0 Instructions for Use 1 1 Record of purchase installation 1 2 Important notes 1 3 Lighting and extinguishing the appliance 1 4 Re laying the coal pebble bed 1 5 Spare parts 1 6 Guarantee Section 2 0 Installation Instructions 2 1 Important notes 2 2 Statutory requirements 2 3 Technical data 2 4 Installing the appliance Ventilation 2 4 1 Flue 2 4 2 Clearance to sides and shelves 2 4 3 Hearth Clearances 2 4 4 Fitting the appliance in position 2 4 4 1 Connecting the gas supply 2 4 4 2 Restrictor Plate 2 4 4 3 Fitting the firebox in the opening 2 4 4 4 Checking the appliance setting pressure 2 4 4 5 Checking the correct operation 2 5 Laying the coal pebble bed 2 6 Clearance of combustion products
9. ION 2 WIRE CABLE FIXING This method is for when it is undesirable to deface or risk damage to the back panel Fig 18 we a Flue outlet Fig 18 See ee ea 1 60mm apart 1 a i Cable fixing holes i Nee fe E gt M Screw eye a i Max Height 300mm P Min Height Boy 150mm Four screw eyes are fixed to the rear of the opening with wall plugs Min height from base of opening 150mm Retaining bush te og a e Max height from base of opening 300mm Screw eyes to be 160mm apart Fix four screw eyes to the rear of the opening note the minimum and maximum height restrictions in the diagram above Thread the wire cable downwards through the two holes located on the lip of the flue outlet Thread through the top two screw eyes and then through the bottom two screw eyes Finally thread through the two holes at the rear of the firebox Pull the wire cable and carefully push the firebox into a central position in the opening Thread each end of the wire cable through the adjusting screw and then through the retaining bush Adjust and tighten to ensure that a good seal is made between the firebox and back panel 12 HM82 010710 2 4 4 4 INSTALLING THE APPLIANCE Checking the appliance setting Super Hot Toaster Mk4 The pressure test point enables verification of the inlet O i pressu
10. PRIOR to installation LL Care must be taken on the selection of wall coverings within close proximity of the appliance as some vinyl and embossed materials may become discoloured by convected heat Soft furnishings must be kept clear from the radiant heat of the appliance and from impinging the hearth area Combustible materials must not be put on or left in the hearth area nor should the coal bed be used to burn rubbish or other materials E This appliance uses fuel effect components gaskets and insulation material containing Refractory Ceramic Fibre RCF which are man made vitreous silicate fibres Excessive exposure to such material may cause temporary irritation to the eyes skin and respiratory tract Consequently it makes sense to take care when handling these articles to ensure that the release of dust is kept to a minimum E This appliance is fitted with an ODS a spillage monitoring system which operates if the evacuation of products is interrupted i e blocked or incorrect flueing If the appliance repeatedly goes out it may indicate a problem and the installer or specialist should be consulted before further use Q The minimum temperature rating of any back panel or hearth must have a minimum fire resistance rating of CLASS 0 100 C LO Materials used in the manufacture of this appliance DO NOT contain asbestos LO When fitting or servicing this appliance care must be taken when handling she
11. UST be installed by a REGISTERED INSTALLER Failure to do so may lead to prosecution LL Ventilation for this appliance must be fitted in accordance with the rules in force and checked regularly for obstructions If the appliance is installed in GREAT BRITAIN additional ventilation is NOT normally required If the appliance is installed in IRELAND a minimal cross sectional area of 100cm is required LL Any permanent flue restriction must be removed and any variable dampers locked fully open or removed If the flue has been used previously for solid fuel it MUST be swept PRIOR to installation E If any soot accumulation becomes excessive the fuel effect pieces should be removed from the appliance for cleaning Cleaning should be carried out in a sufficiently ventilated area or in the open air by gently brushing with the pieces held away from your face so that you avoid inhaling the dust THE USE OF A NORMAL VACUUM CLEANER IS NOT RECOMMENDED as dust may be blown back into the room E This appliance has a naked flame and a fireguard to the current issue of BS 8423 2002 should be used for the protection of children the elderly and the infirm E Care must be taken on the selection of wall coverings within close proximity of the appliance as some vinyl and embossed materials may become discoloured by convected heat Soft furnishings must be kept clear from the radiant heat of the appliance and from impinging the
12. any of the coals or coal bed become damaged or lost replacements MUST be obtained before further use ADDITIONAL COALS PEBBLES MUST NOT BE USED 14 HM82 010710 2 7 2 6 Relight the appliance and allow to run for five minutes with the gas control in the HIGH position Check for satisfactory clearance of combustion products by inserting a lighted smoke match into the opening 30mm down from the edge of the canopy 70mm from either side and 5mm back from the front edge of the canopy Fig 26 The majority of smoke must be drawn up into the flue If this does not occur allow a further 10 minutes and repeat the test Should spillage still occur examine the chimney for fault and rectify The test should be repeated if an extractor fan or fan powered flue appliance is fitted to the room If there is a connected room with an extractor fan the test should be repeated with all the connecting doors to that room opened The front and fret illustrated Fig 27 is a recommended CROSSLEE front and fret If an alternative front and fret is to be used on the appliance it is very important to maintain the equivalent ventilation 2 8 ADVISING THE CUSTOMER Advise the customer on the following points CLEARANCE OF COMBUSTION PRODUCTS Super Hot Toaster Mk4 FRONT AND FRETS REQUIREMENTS FOR VENTILATION Minimum ventilated area of front must be 60cm M
13. et metal parts to avoid any possibility of personal injury LL If any home improvements e g double glazing are carried out after this appliance has been installed you should contact your Registered Installer and have the operation of the flue checked 2 2 STATUTORY REQUIREMENTS IN GREAT BRITAIN A REGISTERED INSTALLER must carry out the installation of this appliance in accordance with the current issue and relevant requirements of This installation booklet The gas safety installation and use regulations The building regulations The building standards Scotland regulations The health and safety at work act The control of substances hazardous to health Any applicable local regulations Noe Ww a Detailed recommendations are contained in the current issue of the following British Standards and Codes of Practice BS 5440 Part 1 Specifications for installation of flues BS 5440 Part 2 Specification for installation of ventilation for gas appliances BS 6461 Part 1 Codes of practice for masonry chimneys and flue pipes BS 5871 Part3 Decorative fuel effect gas appliances of heat input not exceeding 15kW 2 amp 3 family gases BS 6891 Specification for installation of low pressure gas pipe work of up to 28mm R1 in domestic premises on family gases BS 8303 Installation of domestic heating and cooking appliances burning solid mineral fuels BS 1251 Specification for open fireplace componen
14. g 4 Note Large coals pebbles grey and small coals pebbles Metal stops black are coloured for illustration purposes only Front Retaining Bracket Place 5 large coals pebbles on top of the simulated front one in each groove Allow the coals pebbles to rest on the support lt 4 shelf Place 4 large coals pebbles on the on the first tier of the support shelf Fig 5 Place 6 small coals pebbles between the 5 large coals pebbles located on top of the simulated front Allow the coals pebbles to rest on the 4 large coals pebbles on the first tier Place 3 small coals pebbles on top of the 4 large coals pebbles and allow them to rest on the back tier of the support shelf Fig 6 Side View To obtain the best visual appearance it may be necessary to slightly adjust the position of the coals If any of the coals or coal bed become damaged or lost replacements MUST be obtained before further use ADDITIONAL COALS PEBBLES MUST NOT BE USED 5 HM82 010710 1 5 SPARE PARTS Super Hot Toaster Mk4 For a list of spare parts for this appliance please refer to section 3 3 1 6 GUARANTEE Please complete the registration section of the white card supplied in the IFU kit Any part of this appliance is guaranteed against the manufacturer s defective workmanship or faulty materials for a period of twelve months from the date of purchase Any such part will be replaced free of charge on receipt
15. inimum ventilated area of fret must be 50cm The lighting and extinguishing procedures that are described in section 1 3 They should read the Instructions for Use section at the beginning of this booklet The appliance should be serviced at regular intervals and checked for spillage in accordance with the method described in section 2 6 The curing effect of heating the coals will cause an initial odour This is not harmful although additional ventilation i e an opened window may be required until the odour has disappeared If the appliance is turned off or shuts off automatically wait for at least three minutes before attempting to relight 15 HM82 010710 Section 3 Maintenance amp Servicing 3 1 REMOVAL OF DEBRIS OR SOOT Super Hot Toaster Mk4 Allow the appliance to cool for two to three hours before removing all of the fibre components for cleaning purposes Once all the fibre is removed check that no debris is located in the burner holes of the appliance If any debris is located carefully remove any foreign matter from the burner holes Any soot deposits or debris left on the fibre components may be removed by using a soft brush Brush with the component held away from your face so that you avoid inhaling the dust CROSSLEE plc DOES NOT recommend the use of a normal vacuum cleaner which may blow dust back into the room To ensure that the release of fibres from these RCF articles is kept to a minimum during ins
16. liance is suitable for installation into CLASS 1 amp Class 2 flues Class 1 A conventional brick or stone chimney with a minimum effective cross sectional dimension of 225mm x 225mm A lined flue with a minimum diameter of 175mm having a chair brick and throat lintel conforming to the current issue of BS 1251 Fig 9 The minimum distance required between the rear of the opening and the front face of the surround is 220mm lf a chairbrick is fitted it must be removed for this application together with any infill or rubble Any remedial work should be carried out including levelling the base beneath the fire Fig 10 NOTE A restrictor plate is supplied with the IFU kit This restrictor plate Min 25mm Fig 10 Cavity between rear of unit and 9 gt back of flue Fire Class 2 A twin walled metal flue box manufactured to the current issue of BS 715 with a twin walled 125mm diameter flue C and a minimum effective height of 3 metres Fig 11 The flue box must be insulated by the installer using a minimum of 25mm thick insulation NOTE The restrictor plate supplied in the IFU kit Hatched area must be non combustible and flat to ensure a seal around the appliance are must be taken to ensure that the flue spigot from the appliance does not impede the flue outlet from the metal box 25mm thick The area beneath the metal flue box must be a non combustible material l l w 410 490Mm
17. m l l LLLLLLLLLLL IDLY i G f Hatched area must be non combustible and flat to ensure a seal around the appliance HM82 010710 555 590mm 600mm 2 4 2 INSTALLING THE APPLIANCE Clearance to sides and shelves Super Hot Toaster Mk4 The minimum clearance to any combustible material to the side of the appliance must be 150mm Fig 12 The minimum clearance to any non combustible material around the perimeter of the appliance must be 75mm The minimal clearance to the underside of a 150mm depth combustible shelf from the hearth must be 790mm Add 12 5mm to this clearance for every 25mm increased depth of shelf Fig 12 A SHELF CHART Fig 13 is provided to aid in calculating clearances to shelves 2 4 3 go25 Add 12 5mm to clearance for every eh 840 25mm increased depth of shelf i 827 5 815 802 5 ae ee Janae nn Shelf Height 790 oe Fig 13 SHELF CHART i i i i i i i i i r i i i i 1 i i i r r i i i i i i i i H i i i i i i i i Shelf Depth 150 175 200 229 2 9 250 All dimensions are in MM INSTALLING THE APPLIANCE Hearth clearances A non combustible hearth with a minimum thickness of 12 5mm and having a perimeter of 50mm above floor level is required to discourage placing carpets or combustible materials close to the hearth The width must be a minimum of 150mm either side of the fireplace opening and a depth of 300mm from the
18. of the purchaser s address at the cost of postage only Please take time to fill in section 1 1 of this booklet for your future reference 6 HM82 010710 Section 2 Instructions for Installation 2 1 IMPORTANT NOTES Super Hot Toaster Mk4 CAUTION THIS PACKAGE WEIGHS 15 Kgs assess the load before you move it and note any other handling information on the packaging If you think the load is beyond your safe capability DO NOT PUT YOURSELF AT RISK Seek assistance from other person s and or use appropriate handling equipment ITS YOUR BODY LOOK AFTER IT 1 This appliance is for DECORATIVE PURPOSES ONLY and is manufactured to the requirements of the current issue of EN 509 L This appliance is for use on NATURAL GAS G20 ONLY at a supply pressure of 20mbar 1mbar LU IN GREAT BRITAIN this appliance MUST be installed by a REGISTERED INSTALLER Failure to do so may lead to prosecution LL Ventilation for this appliance must be fitted in accordance with the rules in force and checked regularly for obstructions If the appliance is installed in GREAT BRITAIN additional ventilation is NOT normally required If the appliance is installed in IRELAND a minimal cross sectional area of 100cm is required LL Any permanent flue restriction must be removed and any variable dampers locked fully open or removed If the flue has been used previously for solid fuel it MUST be swept
19. re at the appliance under operating conditions and o e a m can also be used to check the gas soundness of the im connections to the appliance gas controls Fig 19 7 JJ N _ a NS Fig 19 Restrictor eloow c w PTP Control knob Pressure Test Point Rating label 2 4 4 5 INSTALLING THE APPLIANCE Checking the correct operation 1 Remove the fret Fig 20 to gain access to the controls Fig 21 eet L asa ai i hi a Fig 21 a f fc 2 Q L T j Oo e Gas Control Fig 20 OH 2 Press and turn the gas control anti clockwise to the IGN position Keep the control fully depressed 3 Once the main burner is lit keep the gas control depressed for a further 20 seconds 4 Release the gas control and check that the main burner has remained alight 5 Press and turn the gas control anti clockwise to the required setting Replace the fret 6 To turn the appliance off depress and turn the gas control to the OFF position 7 In the event of the piezo ignition failing the appliance may be lit by placing a lighted taper or match at the main burner while depressing the gas control in the IGN position IMPORTANT After turning off or if the appliance goes out for any reason wait three minutes before attempting to relight 13 HM82 010710 LAYING THE COAL PEBBLE BED Super Hot Toaster Mk4 metalwork There are two metal stops that prevent
20. tallation and servicing CROSSLEE recommend that a HEPA filtered vacuum is used to remove any dust and soot accumulated in and around the appliance before and after working When replacing these articles CROSSLEE recommend that they are NOT broken up but are sealed in heavy duty polythene bags and clearly labelled as RCF WASTE This is not classified as hazardous waste and may be disposed of at a tipping site licensed for the disposal of industrial waste Protective clothing is not required when handling these articles although CROSSLEE recommend you follow the normal hygiene rules of not smoking eating or drinking in the work area and to always wash your hands before doing so 3 2 SERVICING COMPONENTS BELOW THE BURNER To gain access to the components below the burner remove the fibre components and the burner unit from the firebox CLEANING OR REPLACING THE INJECTOR Fig 28 Fig 2 Unscrew the compression nuts from the gas control to the injector g 8 Remove the formed pipe Unscrew the injector from the burner Replace in reverse order REPLACING THE GAS CONTROL Fig 29 Fig 29 SCS KS Disconnect the two formed pipes from the gas control Disconnect the thermocouple from the gas control o gt Remove the control knob SA 5 Undo the retaining nut on the facia panel KAUAS eo gt i Replace in reverse order REPLACING THE MAIN BURNER amp THERMOCOUPLE Fig 30 Atmospheric sensing device Unscrew
21. the support shelf from sitting on the main burner outlet Fig 22 f The support shelf is positioned on the fibre support 1 Fig 23 JW m Jin urs Fon an Ti in Metal stops The simulated front is positioned on the shelf directly in front of the support shelf Two metal stops locate the simulated front in position Fit the two front retaining brackets with the two No 8x3 8 screws supplied in the fixing pack to secure the front into position Fig 23 Note Large coals pebbles grey and small coals pebbles Metal stops black are coloured for illustration purposes only Front Retaining Bracket Place 5 large coals pebbles on top of the simulated front one in each groove Allow the coals pebbles to rest on the support lt __ shelf Place 4 large coals pebbles on the on the first tier of the support shelf Fig 24 Place 6 small coals pebbles between the 5 large coals pebbles located on top of the simulated front Allow the coals pebbles to rest on the 4 large coals pebbles on the first tier Place 3 small coals pebbles on top of the 4 large coals pebbles and allow them to rest on the back tier of the support shelf Fig 25 Side View To obtain the best visual appearance it may be necessary to slightly adjust the position of the coals If
22. ts In IE the installation must be carried out by a competent engineer in accordance with the current issue and relevant requirement of This installation booklet The rules in force and any local regulations IS 813 issued by the National Standards Authority of Ireland This installation booklet must not be taken as overriding statutory requirements 7 HM82 010710 2 3 TECHNICAL DATA Super Hot Toaster Mk4 Fig 7 Fig 8 Minimum Ra X height of opening is 590mm 600mm Minimum Depth of L Ss 4 Opening is LL a A ee 220mm L l _ _ a lt 505mm gt Minimum Depth is width of 180mm w out cable fixing opening is 220mm with cable fixing 410mm SPECIFICATIONS 6 55kW 22 348 btu hr Gross 2 4 INSTALLING THE APPLIANCE Ventilation Ventilation required for this appliance must be fitted with the rules in force and checked regularly for obstructions If the appliance is installed in GREAT BRITAIN additional ventilation is NOT normally required If the appliance is installed in IRELAND a minimal cross sectional area of 100cm is required 8 HM82 010710 Super Hot Toaster Mk4 2 4 1 INSTALLING THE APPLIANCE Flue Any permanent flue restriction must be removed and any variable dampers locked fully open or removed If the flue has been used previously for solid fuel it must be swept PRIOR to installation This app
Download Pdf Manuals
Related Search