Installing The PCIU
Contents
1. COMDIAL Installing The Personal Computer Interface Unit Introducing The Personal Computer Interface Unit The Personal Computer Interface Unit PCIU is a device that you can connect between a digital station port and its proprietary telephone The PCIU allows telephone users to initiate telephone related functions from their personal computers PC Applications such as this are commonly known as Computer Telephony Integration CTI applications The PCIU will function with Comdial digital telephone systems the DSU and DSU II systems and Comdial digital communications systems currently the DXP DXP Plus and Impact FX systems The PCIU includes Service Provider Interface SPI software on computer floppy disks When you install this SPI software on a PC the PC users can employ their Telephony Applications Programming Interface TAPD third party Microsoft Windows applications programs to control many useful telephone functions Microsoft Windows is a registered trademark of Microsoft Corporation Redmond Washington The PCIU comes bundled with wideopen call software Wideopen call is a CTI application that offers on screen call management and a detailed call log This manual has been developed by Comdial Corporation the Company and is intended for the use of its customers and service personnel The information in this manual is subject to change without notice While every effort has been made to eliminate errors the Comp2. Telephony Driver Removing The Existing Telephony Driver If you already have a PCIU in service you must removefrom windows the telephony service provider that the PCIU was installed with To remove an existing PCIU service provider 1 Click on the Start button in the lower left corner of the screen Go to Settings and select Control Panel 2 Double click on the Telephony icon located in the Control Panel dialog 3 Select the Telephony Drivers tab Older versions of the Telephony Control Panel may not have this If you see a Driver Setup button click that 4 Select Comdial PCIU TAPI Service Provider and click Remove If a message box pops up asking if you are sure you want to remove it click Yes Installing The New Telephony Driver After you have physically connected the PCIU to your PC you must install the floppy disk that contains the SPI software that runs the PCIU device into the computer s floppy disk drive drive A To install the telephony driver using Windows95 98 or NT 1 Click on the Start button in the lower left corner of the screen and select Run 2 Type A SETUP at the prompt and click OK 3 A message box will appear asking you to close any other TAPI applications and services before continuing Click OK to continue with the installation The installation window will display the status as the installation progresses 4 Ifusing Windows95 a message box may appear displaying Current version of TAPI
3. and Limitations General Issues The SPI software no longer supports Visual Call Manager VCM If users make a conference with two lines and then place the conference on hold the conference may eventually recall If it does recall the SPI software may not properly identify the states of the calls and the system may lose call control If users attempt to dial a number that has the same area code as the area code entered in the My Location tab of the Telephony Control Panel settings the system may dial the number as a local number just the seven digit number TAPI applications typically provide an option to Dial as a long distance call or Dial as a toll call If not these applications at least allow users to edit the digits to be dialed The PCIU service provider has no control over what digits an application requests to dial Issues Specific To ACT 3 X 4 0 Except for application initiated transfers and conferences ACT Does not provide call processing support for more than one call at a time Therefore when multiple calls are necessary at the same time users must manually handle these calls from their telephones When users hang up a conference from ACT the Hang Up button remains the only active option even though the call has actually hung up To cause the proper options to be displayed users must press the intercom and speaker buttons on the telephone If users make a call place it on hold and then manually make another call
4. line access rather than requiring users to first press the intercom button that application will probably let the user select an Address Selecting a line in that case causes the telephone to seize that line for outbound calls If you change any button mapping for the PCIU telephone the SPI software must query that telephone again to know about the changes See the paragraph titled Responding To Changes In Telephone Settings If users employ an Impact SCS telephone you must insure that the PCIU station s intercom button is at its default button mapping location that is the lower right hand button of the 12 or 24 programmable buttons Also note that the large screen Impact SCS speakerphone does not work with the PCIU Responding To Changes In Telephone Settings 7 IMI89 260 Installing The Personal Computer Interface Unit DXP DXP Plus and FX Issues You can avoid many call processing problems by being sure that the PCIU telephone has line appearances for the lines on which it handles external calls You must set the Enhanced LCD display feature to No its default setting for the class of service in which the PCIU resides If the setting is Yes caller ID information may be invalid and call processing may intermittently fail Changing DND status from within a TAPI application works best when you map a DND button DSU DSUII Issues Changing DND status from within a TAPI application ONLY works when you map a DND button Problems
5. not recent enough Install TAPI 2 1 now If this occurs click Yes The service provider installation program will close itself and run the TAPI 2 1 installation program If a message box ever pops up asking Do you want to keep this file click Yes After TAPI 2 1 is installed remove the floppy disk and click Yes to the prompt that reads Do you want to restart your computer now The computer will restart and automatically continue with the installation 5 A dialog window will appear titled Comdial PCIU Service Provider Select the appropriate system type and com port from the drop down lists 6 Click the Query Start button 7 The computer now configures itself according to your telephone s settings Do not use your telephone while the computer is configuring itself 8 Note that each button that you have mapped to a line has a check box next to it in the Phone Button Usage section The system notifies TAPI applications of calls that ring on all lines with checked boxes therefore Comdial engineers recommend that you uncheck all boxes that do not ring at the PCIU station port When finished click OK 6 Installing The Telephony Driver Installing The Personal Computer Interface Unit IMI89 260 Responding To Changes In Telephone Settings Any time you change the settings on the telephone you must configure the Comdial PCIU s SPI so the computer can become aware of the changes To make the computer aware of changes to th
6. the first call may eventually recall at which point ACT presents the Answer option If users click Answer the system answers the call but then drops the call in a few seconds To prevent this when multiple calls are necessary at the same time users must manually handle them from their telephones ACT is a registered trademark of Symantec Corp Cupertino CA COMDIAL Charlottesville Virginia 22901 2829 World Wide Web http www comdial com
7. alling The PCIU Installing The Personal Computer Interface Unit IMI89 260 115 VAC Outlet PCIU SERIAL PORT PHONE LINE POWER z t t To System Station Connection Male DB9 Serial Port Connector fe 2 a ee een ne eee OEI F Supplied i ee Two Wire 3 Supplied Line Cord a ae Serial Data se Cable tel ns a Sela a E ees oa dees DES A a 7 a p 2 E Digital Station Port ae n g Female DB9 Serial a a Port Connector B 2 ae 4g 47 a 4 TE CLIP TERMIINALS Typical Station Conector Block C00 C110 C0 16 Station Jack Oo E _ Typical PC Typical Comdial Proprietary LCD pelnearogt Speakerphone with Interactive Buttons Making The Cable Connections Installing The PCIU 5 IMI89 260 Installing The Personal Computer Interface Unit Installing The Telephony Driver If this is a first time installation skip the next section and go directly to the section titled Installing The New
8. any disclaims liability for any difficulties arising from the interpretation of the information contained herein The information contained herein does not purport to cover all details or variations in equipment or to provide for every possible contingency to be met in connection with installation operation or maintenance Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser s purposes contact Comdial Inside Sales Department Charlottesville Virginia 22906 Printed in U S A IMI89 260 05 11 98 IMI89 260 Installing The Personal Computer Interface Unit Detailing The PCIU Requirements Minimum PC Requirements The user supplied PC must be running the Windows95 98 or NT operating systems and must provide a serial data port the PCIU includes a 9 pin to 9 pin serial data cable Proprietary Telephone Requirements The PCIU operates properly with any Comdial Impact Impression or DigiTech LCD speakerphones that provide interactive button support with exception of the large screen Impact SCS speakerphone If using a regular Impact SCS speakerphone the INTERCOM button must be located in the default button mapping location that is the lower right hand button of the 12 or 24 programmable buttons System Requirements Minimum Software Requirements for Specific Systems igen pe ncan DSU DSU II DXP DXP Plus FX System Softw
9. are 18A 2A 8A 3A All Available Product Codes Comdial Product Code Product Description PCIU WOC O1 one PCIU and wideopen call software PCIU WOC 06 six PCIUs and wideopen call software PCIU PK1 wideopen call software for PCIU 2 Detailing The PCIU Requirements Installing The Personal Computer Interface Unit IMI89 260 a N a 5 S J J Typical Common Equipment Cabinet User s PC running Comdial supplied SPI plus wideoffice call To Station Port PCIU A Proprietary LCD Speakerphone with Interactive Buttons pciu02a cdr Reviewing The PCIU Concept Detailing The PCIU Requirements 3 IMI89 260 Installing The Personal Computer Interface Unit Installing The PCIU Connect the PCIU between a digital station port on the common equipment cabinet and that port s proprietary digital speakerphone and also to a user supplied PC The PCIU includes Service Provider Interface SPI software that you must load on the user supplied PC The SPI software in conjunction with the wideopen call software allows the PCIU to use the se
10. e telephone 1 Click on the Start button in the lower left hand corner of the screen Go to Settings and select Control Panel 2 Double click on the Telephony icon located in the Control Panel dialog 3 Select the Telephony Drivers tab 4 Select Comdial PCIU Service Provider and click Configure This will bring up the same dialog window as during installation 5 A dialog window will appear titled Comdial PCIU Service Provider Select the appropriate system type and com port from the drop down lists 6 Click the Query Start button 7 The computer now configures itself according to the telephone s settings Do not use the telephone while the computer is configuring itself When finished click OK Understanding Configuration Issues Common Equipment And Telephone Configuration Issues General Issues The default manner in which the PCIU automatically makes outbound calls is as follows selects the intercom line dials access digit or digits like a 9 dial the desired telephone number Although the SPI software supports making calls by first pressing a line button many TAPI applications support only the default manner therefore Comdial engineers recommend that the PCIU station have line group access To make external calls users must enter the digits they need to dial in the Dialing Properties dialog They access this dialog by clicking on Start Control Panel and Telephony If a TAPI application supports direct
11. rial data path between it and the user supplied PC to send messages to the PC and to the telephone s display Complete instructions for installing the SPI software are detailed in the paragraph titled Installing The Telephony Driver Making The Cable Connections Four cable connections are required to the PCIU station line cord digital telephone line cord PC cable and power cable 1 Disconnect the digital LCD speakerphone s line cord from the digital station port connector and plug it into the connector labeled PHONE on the PCIU 2 Connect the supplied serial data cable between the PC s serial data port COM port and the PCIU s serial port connector A 9 pin to 9 pin cable is supplied with the PCIU If you are using a 25 pin serial port on the PC you must use a 9 to 25 pin adapter 3 Plug one end of a standard line cord into the connector labeled LINE on the PCIU Plug the other end of the line cord into the digital station port connector 4 Plug the transformer attached to one end of the power cable into a 115 VAC electrical wall outlet Connect the other end of the power cable into the PCIU connector labeled POWER The green LED on the PCIU turns on to indicate that power is being supplied to the PCIU NOTE PCIU power loss will create the same symptoms as the disconnection of the PCIU from the digital telephone system If this occurs plug the digital telephone directly into a digital station port connector 4 Inst
Download Pdf Manuals
Related Search