DX80 Corporate Office Quick Inst Guide
Contents
1. COMA installed Red Lead down to HV AL ALLA EO2. Part 3 Setup The Corporate Office DX Module is a self contained processing unit that interacts with the DX 80 telephony processor Once the Corporate Office DX has booted up the DX 80 processor discovers its presence and configures the device automatically for 4 port operation The following parameters are set for immediate functionality COMDIAL e The DX 80 UCD Group 24 directory number 433 is set for VM integration Note If other programming existed in UCD Group 24 it is now changed to accommodate VM operation If the previous programming is necessary it must be reprogrammed into a different UCD Group UCD Group 24 is reserved exclusively for Key Voice Mail voice processors when equipped Voice Mail boxes 101 156 are pre configured for immediate operation Routing boxes 3101 3105 3201 3205 and 3301 3305 are pre configured for immediate operation of Key Voice Mail supported UCD Group Overflow Announcements amp 2 and UCD Group Reroute Announcements for UCD Groups I 3 respectively DX 80 Corporate Office DX Installation Quick Reference Guide e Key Voice Mail Boxes 410 414 are pre configured for immediate operation of Menu Routing via the primary answering menu via user dialed digits received 4 7 respectively This allows for simple setup of department call routing by programming members agents of a department into the DX 80 UCD Group The following parameters must be programmed for th
3. e corresponding operation To forward calls from extensions to VM use Extension Predefined Call Forward to the VM UCD Group 24 directory number 433 We recommend using Predefined No Answer Call Forward e To answer CO Lines via the Automated Attendant the CO Lines to be answered must be directed to the VM UCD Group 24 directory number 433 in CO Line Answering Position programming e To answer a specific CO Line with a unique greeting the CO Line s to be answered uniquely must be programmed to ring to the VM UCD Group 24 directory number 433 Also the CO Line directory number 1 740 16 755 must have an associated VM Box to route the call when answered e UCD Overflow and Reroute Announcements must be recorded in the associated VM Box 3101 3305 Record and Auto Record features via VM must be programmed as allowed for each extension that will use the feature DX 80 programming only required Incidental information The DX 80 assigns virtual extension numbers to the 8 channels designated for digital voice paths to the Corporate Office DX These channels are not physical hardware system resources therefore when the Corporate Office DX is installed no DX 80 port loss is sustained The DX 80 directory numbers assigned to the Corporate Office DX voice channels are 157 164 These directory numbers can be seen in the UCD Group 24 Members programming area The 7270 amp 7271 are shipped wit
4. h four ports therefore directory numbers 157 160 are initialized automatically when either system is installed Part 1 Unpacking Checking Your Shipment What came with your Corporate Office DX system The channel directory numbers can be assigned to an extensions Flexible Feature button to view port status hes fees l eee ss a e Corporate Office DX Module hard drive Refer to the DX 80 Corporate Office DX Installation and Supervisor Guide for programming configuration and use RAM system processor etc information for any specific voice mail related features i a The Corporate Office DX Module is equipped with two DB 9 serial port connectors Com is used to program Eight brass colored 2 0 cm standoffs specific Voice Mail features and operations Com 2 is used in conjunction with 7270 only for connection to the DX 80 CPM PC DBA port This allows the 7270 modem to be used for Corporate Office DX programming and DX 80 key system programming Corporate Office DX Installation Quick Reference Guide Note Requires straight through serial cable Please refer to the following documents GCA70 386 Corporate Office DX Installation And Supervisor Guide IMI 72 005 Corporate Office DX Installation Instructions These documents are located on the Comdial e channel at www comdial com COMDIAL Comdial Corporation 106 Cattlemen Road Sarasota Florida 34232 I 800 COMDIAL Printed in U S A bean O ww
5. to the side to provide access to the standoffs that supported the CPM 2 7 Install the standoffs removed in step 2 5 onto each of the existing four standoffs The result is four standoffs that are two standoffs tall 2 8 Reinstall the CPM on the two standoff tall standoffs using four of the new standoffs included with the Corporate Office DX 2 9 Connect the Corporate Office DX ribbon cable to the CPM AAM VP Auto Att Module Voice Processor connector 2 10 Connect the Corporate Office DX keyed power cord white and red connectorized leads to the KSUI 408M VPPWR power connector 2 11 Secure the Corporate Office DX Module onto the CPM using the remaining four new 408M Power Connector standoffs included with the Corporate Office DX 7 2 12 Reinstall the KSU cover and restore power to the DX 8o Turn it on 2 6 Using only four of the eight standoffs included secure the Corporate Office DX Module in place Four of the included standoffs will not be used 2 7 Connect the Corporate Office DX power cord white and red connectorized leads to the keyed power con nector VPPWR on the KSUI 408M board 2 8 Reinstall the KSU cover and restore power to the DX 8o Turn it on A corporate Office DX module ail i CPM module K COM4 module ay 408M bottom an Ay AE JA Corporate Office DX module 1 dus JA CPM module sid module White Lead up to GND Keyed power am ere No
6. w comdial com Part 2 Installation Wear a grounded wrist strap while performing this upgrade Remove the Corporate Office DX and eight standoffs from the shipping carton and set aside on an anti static surface Power down the system and remove the KSUI cabinet cover Four screws Determine how the Corporate Office DX must be mounted 1s there a COM module installed COM Installed COM Not Installed When installing the Corporate Office DX Module with a COM module already installed the Corporate Office DX When installing the Corporate Office DX Module without a COM module already installed Module can be easily installed without repositioning the CPM module When installation is complete the Corporate the CPM module must be repositioned to assure that the Corporate Office DX cooling fan is Office DX cooling fan will be positioned flush with the KSU cover to properly draw outside air into the cabinet for hard positioned flush with the KSU cover to properly draw outside air into the cabinet for hard disk disk cooling cooling This requires the use of all eight standoffs supplied with the Corporate Office DX Module 2 5 Position the Corporate Office DX Module over the CPM and connect the ribbon cable to the CPM AAM VP Automated Attendant Module Voice Processor connector 2 5 Remove the four standoffs that secure the CPM Central Processor Module and set them aside 2 6 Lift the CPM away
Download Pdf Manuals
Related Search