P1177E-871 User`s Manual VA1
Contents
1. H Axom All in One 19 SXGA TFT Expandable PANEL PC Disclaimers This manual has been carefully checked and believed to contain accurate information Axiomtek Co Ltd assumes no responsibility for any infringements of patents or any third party s rights and any liability arising from such use Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy completeness or usefulness of any information in this document Axiomtek does not make any commitment to update the information in this manual Axiomtek reserves the right to change or revise this document and or product at any time without notice No part of this document may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Axiomtek Co Ltd CAUTION If you replace wrong batteries it causes the danger of explosion It is recommended by the manufacturer that you follow the manufacturer s instructions to only replace the same or equivalent type of battery and dispose of used ones Copyright 2014 Axiomtek Co Ltd All Rights Reserved Feb 2014 Version A1 Printed in Taiwan Safety Precautions Before getting started read the following important cautions 1 Be sure to ground yourself to prevent static charge when installing the internal components Use a grounding wrist strap and place2. And remove the protective plastic cover Hardware and Installation 15 P1197E 861 User s Manual Step 2 CPU aims at the socket and places the package carefully into the socket by purely vertical motion W j NOTE Never touch fragile socket contacts to avoid damage and do not touch processor sensitive contacts at any time during installation 16 Hardware and Installation P1197E 861 User s Manual 2 8 CPU Cooler Installation Step 1 Making sure your CPU settled correctly on the socket Step 2 Screw the cooling fan supporting base onto the CPU socket on the Motherboard and make sure the CPU fan is plugged to the CPU fan connector And Connect the CPU cooler power connector to the FAN1 connector Hardware and Installation 17 P1197E 861 User s Manual 2 9 Wireless LAN Module Installation optional The P1197E 861 provides one wireless LAN module to install When installing the wireless LAN module refer to the following instructions and illustration Step 1 Refer to section 2 1 to open the back cover and find out the wireless LAN module located Step 2 Fixing the wireless LAN module by 2 screws 18 Hardware and Installation P1197E 861 User s Manual Step 3 Plug in USB cable to the connector of WIFI module And find the built in Antenna cable and connect it wireless LAN card EES N T 2 002 LNSHM NA 01904 Step A LT the rubber stopper from the top of ba
3. P1197E 861 User s Manual Chapter 2 Hardware and Installation The P1197E 861 provides rich I O ports and flexible expansions for you to meet different demand The chapter will show you how to install the hardware It includes Open back cover Serial Port Interface Ethernet Mounting Method Hard disk DRAM CPU CPU Cooler Wireless LAN Module optional Add on Card Optical Drive Hardware and Installation 7 P1197E 861 User s Manual 2 1 Open back cover This section tells users how to open back cover Please follow the steps below Unscrew 3 screws on the back cover and push to the right side Please refer Step 1 the photo below Step 2 E Pit Wine ec Dn Hardware and Installation P1197E 861 User s Manual 2 2 Serial Ports Interface The P1197E 861 has four serial ports COM1 is RS 232 422 485 while COM2 COM3 and COM4 are RS 232 2 2 1 COM1 amp COM2 Connector The COM1 amp COM2 are double deck DB 9 connectors The upper connector is for COM1 and the lower connector is for COM2 Pn mm ae e an e 17 oeeo o e iere 2 2 2 COM3 amp COM4 Connectors The COM3 and COM4 interfaces are available through COM34 and COM56 respectively Pin Signa Pin Signa C0M34 comse E ET fos r fom hs e e feo TR Tang Hardware and Installation 9 P1197E 861 User s Manual 2 3 Ethernet The P1197E 861 is equipped with two high performance plug and play Etherne
4. This screen shows the CPU information Aptio Setup Utility Copyright C 2011 American Megatrends Inc Active Processor Cores Version 2 14 1219 Copyright C 2011 American Megatrends Inc Active Processor Cores Allow users to set how many processor cores should be active Intel Virtualization Technology This ttem allows a hardware platform to run multiple operating systems separately and simultaneously enabling one system to virtually function as several systems L NOTE This functions will depend on your CPU supported or not AMI BIOS Setup Utility 29 P1197E 861 User s Manual e SATA Configuration In this Configuration menu you can see the currently installed hardware in the SATA ports During system boot up the BIOS automatically detects the presence of SATA devices Aptio Setup Utility Copyright C 2011 American Megatrends Inc SATA Controller s Enabled Version 2 14 1219 Copyright C 2011 American Megatrends Inc SATA Controller s Enable or disable SATA device SATA Mode Selection Determine how SATA controller s operate Operation mode options are IDE Mode AHCI Mode and RAID Mode 30 AMI BIOS Setup Utility P1197E 861 User s Manual e PCH FW Configuration This screen displays Management Engine ME Firmware information Aptio Setup Utility Copyright C 2011 American Megatrends Inc Version 2 14 1219 Copyright C 2011 American Megatrends Inc AMI BIOS S
5. s Manual 4 3 Embedded O S The P1197E 861 provides the Windows 7 Embedded The O S is supported devices which are listed below e WES7 Here are supported onboard devices Onboard Multi UO SATA HDD USB PS2 Keyboard and mouse CRT LCD display 10 100 1000 base T Ethernet Onboard Audio Touch Screen PenMount Touch screen Before you can use and calibrate it here is what you should do 1 Set up Penmount touch device driver by executing C Penmount Windows 2000 XP V5 0 setup exe When the installation is finished an icon PM appears on the Taskbar 2 Calibrate Penmount touch by clicking on the PM icon and the go on the calibration 3 Restart the computer 52 Drivers Installation
6. 1 Introduction ssssssssssssssssescsssccccsees f 1 1 1 2 1 3 1 4 1 5 G neral Red le EE 1 TRT OT ALON EE 2 DIMENSIONS and OUTINGS essesscciecnisseveccicaciccensectscwessswwaussasersesencsnentsenis 4 Heel 5 PACKING EIS EE 5 Chapter 2 Hardware and Installation ennen 7 2 1 2 2 2 3 2 4 2 5 2 6 2 1 2 8 2 9 2 10 2 11 Open back e EE 8 Serial Ports Interface cssss sss ss sss s esse enesenn nenen ennenen enen 9 2 2 1 COM1 amp COM2 Connector aisina aa a a E a 9 2 2 2 COM3 amp COM4 ecli e eT 9 ENGNG EE 10 Mountings Panel Wall Rack Desktop VES sss sese s sese sese 10 2 4 1 VESA ARM Wall Mount Desktop mounmt sss sse sees eee 10 2 4 2 Panel mount Kit Assembly uk 11 2 4 3 Rack mount Kit Assembly eee ee eee eee ee 12 ADD TS Talat O er EEE EES E HR SERR GERE GEZ 12 DRAM INSTA AUO MN DEN 13 CPU Installateur Genee 15 CPU Cooler Installation ccccceesssecnecssseseeceseneenseceseneeneeeseneeneneas 17 Wireless LAN Module Installation optional ccesseesee 18 Add on Card Installation c cccccsesssscsecsesenseneeceseneeeeseneeneeseeeneeneseas 20 Optical Drive Installation Optional ssssssssssssssssssss sss sssss essen esse 22 Chapter A AMI BIOS Setup Utility ssssssssssssssssssssssss 29 3 1 3 2 3 3 3 4 3 5 SANNO TT 25 K Vlet el 8 dE 25 Machine 26 THEGO Bl 10 0 EE 27 ll E O IMC TUN EE 38 3 6 Boot 0 0 nnn 46 Sf Save
7. IO Configuration You can use this screen to select options for the Super IO Configuration and change the value of the selected option A description of the selected item appears on the right side of the screen For items marked with gt please press lt Enter gt for more options Aptio Setup Utility Copyright C 2011 American Megatrends Inc gt Serial Port 1 Configuration Version 2 14 1219 Copyright C 2011 American Megatrends Inc Serial Port 1 2 Configuration Use these items to set parameters of serial port 1 2 Parallel Port Configuration Use this item to set parameters of parallel port Watch Dog Timer Enable or disable watchdog timer function Chassis Opened Warning Enable or disable chassis opened warning setting AMI BIOS Setup Utility P1197E 861 User s Manual e H W Monitor Use this screen for Smart Fan configuration and hardware health status monitoring Aptio Setup Utility Copyright C 2011 American Megatrends Inc gt Smart Fan Version 2 14 1219 Copyright C 2011 American Megatrends Inc This screen displays the temperature of system and CPU cooling fan speed in RPM and system voltages VCORE 12V 5V 5VSB etc Smart Fan This option allows users to configure Smart Fan function AMI BIOS Setup Utility 35 P1197E 861 User s Manual e Option Rom Policy Aptio Setup Utility Copyright C 2011 American Megatrends Inc Boot option filter UEFI a
8. all electronic components in any Static shielded devices Most electronic components are sensitive to static electrical charge Disconnect the power cords from the P1197 Series before making any installation Be sure both the system and the external devices are turned OFF Sudden surge of power could ruin sensitive components Make sure the P1197 Series is properly grounded Do not open the system s top cover If opening the cover for maintenance is a must only a trained technician is allowed to do so Integrated circuits on computer boards are sensitive to static electricity To avoid damaging chips from electrostatic discharge observe the following precautions S Before handling a board or integrated circuit touch an unpainted portion of the system unit chassis for a few seconds This will help to discharge any static electricity on your body m When handling boards and components wear a wrist grounding strap available from most electronic component stores Trademarks Acknowledgments Axiomtek is a trademark of Axiomtek Co Ltd Windows is a trademark of Microsoft Corporation IBM PC AT PS 2 VGA are trademarks of International Business Machines Corporation Intel and Pentium are trademarks of Intel Corporation AMI is trademark of American Megatrend Inc Other brand names and trademarks are the properties and registered brands of their respective owners Table of Contents DIS ei il Dalely 1 E lil Chapter
9. from the Save amp Exit menu and press lt Enter gt Select Yes to save changes and reset e Restore Defaults It automatically sets all Setup options to a complete set of default settings when you select this option Select Restore Defaults from the Save amp Exit menu and press lt Enter gt e Boot Override Select a drive to immediately boot that device regardless of the current boot order AMI BIOS Setup Utility 47 P1197E 861 User s Manual This page is intentionally left blank 48 AMI BIOS Setup Utility P1197E 861 User s Manual Chapter 4 Drivers Installation 4 1 System P1197E 861 supports Windows 7 and WES 7 To facilitate the installation of system driver please carefully read the instructions in this chapter before start installing Step 1 Insert Driver CD and select the Drivers Optional Step 1 Chipset Step 2 Graphic L L L Kl Step 4 USB 3 0 for Step 5 HD Audio Step 6 Touch Step 7 ME Win Step 2 Select all files and follow the installing procedure 4 2 Touch Screen The P1197E 861 uses the 5 wire analog resistive There are the specification and driver installation which are listed below e Specification Touch Screen 5 wire Analog Resistive type Touch Screen Controller PenMount 6500 USB Touch Screen Controller IC Communications USB interface Baud Rate 19200 baud rate fixed Resolution 1280 X 1024 Drivers Installation 49 P1197E 861 User s Manual
10. 7E 861 User s Manual 3 3 Main Menu When you first enter the setup utility you will enter the Main setup screen You can always return to the Main setup screen by selecting the Main tab System Time Date can be set up as described below The Main BIOS setup screen is shown below Aptio Setup Utility Copyright C 2011 American Megatrends Inc Advanced Chipset Boot Save amp Exit System Date Version 2 14 1219 Copyright C 2011 American Megatrends Inc BIOS Information Display the auto detected BIOS information System Date Time Use this option to change the system time and date Highlight System Time or System Date using the lt Arrow gt keys Enter new values through the keyboard Press the lt Tab gt key or the lt Arrow gt keys to move between fields The date must be entered in MM DD YY format The time is entered in HH MM SS format 26 AMI BIOS Setup Utility P1197E 861 User s Manual 3 4 Advanced Menu The Advanced menu also allows users to set configuration of the CPU and other system devices You can select any of the items in the left frame of the screen to go to the sub menus ACPI Settings CPU Configuration SATA Configuration PCH FW Configuration USB Configuration Second Super IO Configuration Super IO Configuration H W Monitor Option Rom Policy CPU PPM Configuration Y Y Y YYY YY Y Y For items marked with K please press lt Enter gt for more options Aptio Setup Utility Co
11. Dimension Main Body Size m 482 x 94 7 x 380mm e Operation Temperature m OC to45C e Relative Humidity m 10 to 95 40 C Non Condensing e Power Input m 100 240VAC power connector M NOTE 1 All specifications and images are subject to change without notice 2 The speed of expansion card will depend on your CPU 3 On Screen Display Combo keys Pressing VOL amp VOL means Audio mute Introduction 3 P1197E 861 User s Manual 1 3 Dimensions and Outlines The following diagrams show the dimensions and outlines of P1197E 861 CUT OUT DIM SCT Cat S L LT A Introduction P1197E 861 User s Manual 1 4 UO Outlets Please refer to the following illustration for I O locations of the P1197E 861 QA OO Q Q 1 AC Plug 6 Audio Mic in Line out 11 4x USB2 0 2 PS2 Keyboard amp Mouse combo 7 1x PCle x 4 or 1 x PCI 12 1x RS 232 COM3 3 1x RS 232 422 485 COM1 9 2x USB2 0 13 1x RS 232 COM4 4 1x VGA 9 1x RS 232 COM2 14 Power Switch 5 Ethernet x2 10 1x DVI D 1 5 Packing List When you receive the P1197E 861 the bundled package should contain the following items P1197E 861 unit x 1 Driver CD x1 Panel mount kit x 9 Wall VESA mount kit x 1 optional Power cord x 1 If you can not find the package or any items are missing please contact Axiomtek distributors immediately Introduction 5 P1197E 861 User s Manual This page is intentionally left blank 6 Introduction
12. Installation The P1197E 861 provides a convenient Hard Disk Drive HDD bracket for users to install 2 x 2 5 SATA HDD Please follow the steps Step 1 Unscrew 1 screws to take off the HDD door Step 2 Unscrew two screws and pull the HDD out directly 12 Hardware and Installation P1197E 861 User s Manual 2 6 DRAM Installation The P1197E 861 provides two 204 pin DDR3 SO DIMM socket that support system memory up to 16GB Please follow steps below to install the memory modules Step 1 Refer to section 2 1 to open the back cover and find out DIMM socket on mainboard MANO871 d SE di D E BREL Im X L R f ef CC B d x a Step 2 Push the latches on each side of the SO DIMM slot down Hardware and Installation 13 P1197E 861 User s Manual Step 3 Install the SO DIMM module into the slot and press it firmly down until it seats correctly Step 4 The slot latches are levered upwards and latch on to the edges of the SO DIMM 14 Hardware and Installation P1197E 861 User s Manual 2 7 CPU Installation The P1197E 861 has an LGA1155 socket supporting Intel 3 amp 2 Core i7 i5 i3 series Pentium and Celeron processors and provides high computing performance for users Step 1 Press the hook of lever down with your thumb and pull it to the right side to release it from retention tab Step 2 Lift the tail of the load lever and rotate the load plate to fully open position
13. Keys The BIOS setup utility uses a key based navigation system called hot keys Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process These keys include lt F1 gt lt F2 gt lt Enter gt lt ESC gt lt Arrow gt keys and so on W NOTE Some of the navigation keys differ from one screen to another gt lt Left Right The Left and Right lt Arrow gt keys allow you to select a setup screen AV Up Down The Up and Down lt Arrow gt keys allow you to select a setup screen or sub screen The Plus and Minus lt Arrow gt keys allow you to change the field value of a Plus Minus paper setup item The lt Tab gt The lt Tab gt key allows you to select setup fields allows you to select setup fields The lt F1 gt key allows you to display the General Help screen The lt F2 gt key allows you to Load Previous Values The lt F3 gt key allows you to Load Optimized Defaults The lt Esc gt key allows you to discard any changes you have made and exit the Setup Press the lt Esc gt key to exit the setup without saving your changes The lt Enter gt key allows you to display or change the setup option listed for a particular setup item The lt Enter gt key can also allow you to display the setup sub screens The lt F4 gt key allows you to save any changes you have made and exit Setup Press the lt F4 gt key to save your changes AMI BIOS Setup Utility 25 P119
14. NB PCle Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc PEGO Gen X version 2 14 1219 Copyright C 2011 American Megatrends Inc PEGO Gen X Select PEGO speed PEGO ASPM Control ASPM support for the PEG device Enable PEG Enable or disable PEG always Detect Non Compliance Device Enable or disable the detection of a non compliance PCI Express device in PEG 44 AMI BIOS Setup Utility P1197E 861 User s Manual e Memory Configuration This screen displays system memory information Aptio Setup Utility Copyright C 2011 American Megatrends Inc Version 2 14 1219 Copyright C 2011 American Megatrends Inc AMI BIOS Setup Utility 45 P1197E 861 User s Manual 3 6 Boot Menu The Boot menu allows users to change boot options of the system Aptio Setup Utility Copyright C 2011 American Megatrends Inc Main Advanced Chipset s Save amp Exit Setup Prompt Timeout Version 2 14 1219 Copyright C 2011 American Megatrends Inc e Setup Prompt Timeout Number of seconds to wait for setup activation key 65535 0xFFFF means indefinite waiting e Bootup NumLock State Use this item to select the power on state for the keyboard NumLock e Quiet Boot Select to display either POST output messages or a splash screen during boot up e Boot Option Priorities These are settings for boot priority Specify the boot device priority sequence from the availab
15. Se Exit MEHU WEEN 47 Chapter 4 Drivers lnsetallation ssssssssssssssssssssssssssssss 49 AP SyS lO WEE 49 42 TOUCH en EEN 49 ASS Embedded hee dee aa a ae iaia 52 This page is intentionally left blank vi P1197E 861 User s Manual Chapter 1 Introduction This chapter contains general information and detailed specifications of the P1197E 861 Chapter 1 includes the following sections General Description Specification Dimensions and Outlines UO Outlets Package List 1 1 General Description The P1197E 861 adopts a 19 inch SXGA TET LCD with 350 nits brightness and Intel 3rd amp 2nd Core i7 i5 i3 series Pentium and Celeron processors and Intel H61 chipset to provide excellent and powerful computing performance Furthermore P1197E 861 adopts built in speaker and option WLAN module for wireless connectivity Industrial grade front bezel P1197E 861 adopts industrial grade material front bezel which incorporates the advantages of light weight high degree of hardness better heat releasing easy to shape and anti corrosion ability Therefore P1197E 861 is especially suitable for most rugged industrial environments Expandable for 1 PCle 1 PCI optional P1197E 861 has 1 PCle 1 PCI optional for expansion purpose User can easily plug in standard half size PCI or PCle card for any requirement Speaker and WLAN Antenna Supported P1197E 861 features built in speakers for kiosk application to display multimedi
16. a content program It also supports WLAN module optional antenna for wireless network connectivity Powerful computing Intel 3rd Generation Core i7 i5 i3 Celeron processors P1197E 861 features Intel 3 amp 2 Core i7 i5 i3 series Pentium and Celeron processors and Intel H61 chipset which deliver high computing performance capability Ivy Bridge CPU offers reliable and stable performance and rugged environment Introduction 1 P1197E 861 User s Manual 1 2 Specifications Main CPU Board e CPU a Intel 3rd amp 2nd Core i7 i5 i3 series Pentium and Celeron processors e System Chipset m Intel H61 Express Chipset e System Memory m 2x 204 pin DDR3 SO DIMM socket Supporting 8GB per DIMM maximum memory size up to 16GB e BIOS America Megatrends BIOS AMI UEFI BIOS I O System e Standard UO m 1x RS 232 422 485 COM1 1 x RS 232 with 5V 12V COMS 3 x RS 232 COM4 2 x USB 2 0 front 6 x USB 2 0 back 1 x DVI D 1x VGA e Ethernet m 2x RJ45 for Giga Ethernet e Audio 1x Line out m 1x Mic in e Expansion 1x Wireless Module optional m 1xPClex 4 slots Riser card 1 x PCI slots Riser card optional e Storage m 2x 2 5 SATA HDD e Power connector m 1xAC plug 2 Introduction P1197E 861 User s Manual System Specification e 19 SXGA 1280 X 1024 LCD e 5 wired resistive Touch e IP65 NEMA4 aluminum front bezel e IP65 aluminum front bezel e Net Weight m 8kgs 17 64 lb e
17. ck cover Step 5 Install the antenna on the antenna connector Hardware and Installation 19 P1197E 861 User s Manual 2 10 Add on Card Installation The P1197E 861 provides a riser card PClex4 interface for 1 x PCle x 4 or 1 x PCI slots expansion The riser card assembly can accommodate both half size expansion cards To install the riser card refer to the following figure and instructions below Step 1 Refer section 2 1 to open the back cover and unscrew 2 screws and then remove the riser card fix kit and plate w be 4 Bp a KR d p a aR d ge P C e d x RE E Te x er lt gt ee Step 3 Insert the riser card in the socket firmly until it is completely seated And insert the add on card you need to the socket of riser card TI TALLAN 20 Hardware and Installation P1197E 861 User s Manual Step 4 Secure the metal bracket of the card to the system case with four screws Installations complete LY sad NOTE Please use the standard size of add on card to avoid conflicting the mechanism Hardware and Installation 21 P1197E 861 User s Manual 2 11 Optical Drive Installation optional The P1157E 871 offers a convenient drive bay module for users to install optical drive When installing the optical drive refer to the following instructions and illustration Step 1 Refer section 2 1 to open the back cover Step 2 Unscrew four screws to remove the plate from t
18. e Driver Installation Windows 7 The P1197E 861 provides a touch screen driver that users can install it under the operating system Windows 7 To facilitate installation of the touch screen driver you should read the instructions in this chapter carefully before you attempt installation Step 1 Insert Driver CD and follow the path to select the Drivers Step 6 Touch Driver Utility al ev A e Setup Setup Step 2 Follow the installing procedure and press OK Step 3 Click Start menu and select PenMount Utilities and then a PenMount Control Panel pops out PenMount Control Panel Device Multiple Moritors Tools About ony Penmourt Control Panel Version 1 0 0 63 Installed Device s Device 0 Pen ourt 6500 L58 Suppcrt E mal CectoLch ceeire ba Support Website nite aan Denmount com tw 50 Drivers Installation P1197E 861 User s Manual Step 4 Select the Standard Calibrate tab Device 0 Pentdount 6500 USR ca Erase Setting Edge Compensation About Advanced Moce 9 D Ekt cabbrstion dets Standard Cata Odverced Calbestion Tun off EEPROM storage Step 5 Calibrations To adjust the display with touch panel click Calibration and follow the calibrate point to do calibration there are five points on screen for calibration a i Touch the rad square Step 6 Press OK Drivers Installation 5i P1197E 861 User
19. etup Utility 31 P1197E 861 User s Manual e USB Configuration You can use this screen to select options for the USB Configuration and change the value of the selected option A description of the selected item appears on the right side of the screen Aptio Setup Utility Copyright C 2011 American Megatrends Inc Legacy USB Support Enabled Version 2 14 1219 Copyright C 2011 American Megatrends Inc USB Devices Display all detected USB devices Legacy USB Support Use this item to enable or disable support for USB device on legacy operating system The default setting is Enabled Auto option disables legacy support if no USB devices are connected Disable option will keep USB devices available only for EFI applications 32 AMI BIOS Setup Utility P1197E 861 User s Manual e Second Super IO Configuration You can use this screen to select options for the Second Super IO Configuration and change the value of the selected option A description of the selected item appears on the right side of the screen For items marked with gt please press lt Enter gt for more options Aptio Setup Utility Copyright C 2011 American Megatrends Inc gt Serial Port 3 Configuration Version 2 14 1219 Copyright C 2011 American Megatrends Inc Serial Port 3 6 Configuration Use these items to set parameters of serial port 3 6 AMI BIOS Setup Utility 33 P1197E 861 User s Manual 34 Super
20. he right side Step 3 Fixing the optical drive on the bracket A Fixing optical drive by 4 screws 22 Hardware and Installation P1197E 861 User s Manual Step 4 Fixing the optical drive kit on the chassis by 4 screws amp R N E F 2 V f Step 5 Plug the power and SATA cables to connectors Installation completes Hardware and Installation 23 P1197E 861 User s Manual This page is intentionally left blank 24 Hardware and Installation P1197E 861 User s Manual Chapter 3 AMI BIOS Setup Utility The AMI UEFI BIOS provides users with a built in setup program to modify basic system configuration All configured parameters are stored in a flash chip to save the setup information whenever the power is turned off This chapter provides users with detailed description about how to set up basic system configuration through the AMI BIOS setup utility 3 1 Starting To enter the setup screens follow the steps below 1 Turn on the computer and press the lt Del gt key immediately 2 After you press the lt Del gt key the main BIOS setup menu displays You can access the other setup screens from the main BIOS setup menu such as the Advanced and Chipset menus It is strongly recommended that you should avoid changing the chipset s defaults Both AMI and your system manufacturer have carefully set up these defaults that provide the best performance and reliability 3 2 Navigation
21. le devices 46 AMI BIOS Setup Utility P1197E 861 User s Manual 3 7 Save amp Exit Menu The Save amp Exit menu allows users to load your system configuration with optimal or fail safe default values Aptio Setup Utility Copyright C 2011 American Megatrends Inc Main Advanced Chipset Boot Save amp Exit Exit system setup after saving Discard Changes and Exit the changes Save Changes and Reset Restore Defaults Boot Override Select Screen Tl Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 14 1219 Copyright C 2011 American Megatrends Inc 6 Save Changes and Exit When you have completed the system configuration changes select this option to leave Setup and return to Main Menu Select Save Changes and Exit from the Save amp Exit menu and press lt Enter gt Select Yes to save changes and exit e Discard Changes and Exit Select this option to quit Setup without making any permanent changes to the system configuration and return to Main Menu Select Discard Changes and Exit from the Save amp Exit menu and press lt Enter gt Select Yes to discard changes and exit e Save Changes and Reset When you have completed the system configuration changes select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect Select Save Changes and Reset
22. nd Legacy Version 2 14 1219 Copyright C 2011 American Megatrends Inc Boot Option Filter This option controls what devices system can boot to Launch PXE OpROM policy Enable or disable boot options for legacy network devices Launch Storage OpROM policy Control the execution of UEFI and legacy storage ODROM 36 AMI BIOS Setup Utility P1197E 861 User s Manual CPU PPM Configuration Use this screen for CPU PPM configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Enabled Version 2 14 1219 Copyright C 2011 American Megatrends Inc EIST Enable or disable Intel SpeedStep When enabled CPU speed is controlled by the operating system When disabled CPU runs at its default speed Turbo Mode This item is for enabling or disabling turbo mode When enabled it allows processor cores to run faster than marked frequency under certain conditions CPU C3 Report Enable or disable CPU C3 report to the operating system CPU C6 Report Enable or disable CPU C6 report to the operating system NOTE This functions will depend on your CPU supported or not AMI BIOS Setup Utility 37 P1197E 861 User s Manual 3 5 Chipset Menu The Chipset menu allows users to change the advanced chipset settings You can select any of the items in the left frame of the screen to go to the sub menus K PCH IO Configuration gt System Agent SA Configuration For items marked with gt please pres
23. pyright C 2011 American Megatrends Inc Main Chipset Boot Save amp Exit gt ACPI Settings Version 2 14 1219 Copyright C 2011 American Megatrends Inc Take caution when changing the settings of the Advanced menu items Incorrect field values can cause the system to malfunction Caution AMI BIOS Setup Utility 27 P1197E 861 User s Manual 28 ACPI Settings You can use this screen to select options for the ACPI configuration and change the value of the selected option A description of the selected item appears on the right side of the screen Aptio Setup Utility Copyright C 2011 American Megatrends Inc ACPI Sleep State S3 onlyCSuspend to Version 2 14 1219 Copyright C 2011 American Megatrends Inc ACPI Sleep State Select the highest ACPI sleep state the system will enter when the suspend button is pressed Configuration options are Suspend Disabled S1 only CPU Stop Clock and S3 only Suspend to RAM To correctly support wake by use of USB from the S3 system power state please refer to the following Microsoft s link http support microsoft com kb 841858 en us S3 Video Repost Enable or disable video repost Resume On RTC Alarm Enable or disable system wake on alarm even When enabled system will wake upon the hr min sec specified Wake On PCIE Enable or disable PCIE to generate a wake event AMI BIOS Setup Utility P1197E 861 User s Manual e CPU Configuration
24. s lt Enter gt for more options Aptio Setup Utility Copyright C 2011 American Megatrends Inc Main Advanced Boot Save amp Exit K PCH IO Configuration version 2 14 1219 Copyright C 2011 American Megatrends Inc 38 AMI BIOS Setup Utility P1197E 861 User s Manual e PCH IO Configuration This screen allows users to set PCH parameters Aptio Setup Utility Copyright C 2011 American Megatrends Inc gt USB Configuration Version 2 14 1219 Copyright C 2011 American Megatrends Inc USB Configuration USB configuration settings PCH Azalia Configuration PCH Azalia device configuration settings LAN1 Controller Enable or disable LAN1 controller LAN2 Controller Enable or disable LAN2 controller Mini PCle Speed Allow you to select mini PCI Express speed Restore AC Power Loss Set the system power status when power returns from a power failure situation The system power status options are Power Off Power On and Last State AMI BIOS Setup Utility 39 P1197E 861 User s Manual e PCH USB Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Enabled Version 2 14 1219 Copyright C 2011 American Megatrends Inc EHCI1 EHCI2 Enable or disable the EHCI controller USB Ports Per Port Disable Control Enable or disable each USB port individually 40 AMI BIOS Setup Utility P1197E 861 User s Manual e PCH Azalia Configuration Aptio Se
25. t interfaces RJ 45 Connection can be established by plugging one end of the Ethernet cable into this RJ 45 connector and the other end to a 1000 100 10 Base T hub Each of these ports allows Gigabit connection to a Local Area Network LAN through a network hub Refer to the table below for the LAN port LED indications SE ACT LINK LED SPEED ACT LINK Status Description Status _ Description me 2 1Gbps connection Blinking Data activity 2 4 Mountings Panel Wall Rack Desktop VESA There are 5 application options for the P1197E 861 including Panel Wall Rack Desktop VESA mounting ways 2 4 1 VESA ARM Wall Mount Desktop mount The P1197E 861 provides VESA mount 75x75 mm or 100x100mm Screw six screws to fix the kit in the back chassis AVESA Wall mount bracket 10 Hardware and Installation P1197E 861 User s Manual A Fixing the bracket by four screws on the left and right side 2 4 2 Panel mount Kit Assembly The P1197E 861 is designed for panel mount application To mount the P1197E 861 the standard set of mounting kit included in the system packaging is needed d O OOOO Ki K L L ST d Ee VW Hardware and Installation 11 P1197E 861 User s Manual 2 4 3 Rack mount Kit Assembly The P1197E 861 is designed for rack mount application Step 1 Remove 8 seal pads in front panel Step 2 P1197E 861 could mount directly to standard 19 industrial rack 2 5 HDD
26. tup Utility Copyright C 2011 American Megatrends Inc Azalia Version 2 14 1219 Copyright C 2011 American Megatrends Inc Azalia Control detection of the Azalia device Configuration options are Disabled Enabled and Auto AMI BIOS Setup Utility 41 P1197E 861 User s Manual e System Agent SA Configuration This screen shows System Agent information and provides function for specifying related parameters For items marked with gt please press lt Enter gt for more options Aptio Setup Utility Copyright C 2011 American Megatrends Inc Enabled Version 2 14 1219 Copyright C 2011 American Megatrends Inc VT d Enable or disable Intel chipset virtualization technology for directed UO VT d can help end users improve security and reliability of the systems and also improve performance of I O devices in virtualized environment 42 AMI BIOS Setup Utility P1197E 861 User s Manual e Graphics Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Primary Display Version 2 14 1219 Copyright C 2011 American Megatrends Inc Primary Display Allow you to select which graphics controller to use as the primary boot device Internal Graphics Enable or disable IGD DVMT Pre Allocated Select DVMT pre allocated memory size DVMT Total Gfx Mem Select DVMT total memory size AMI BIOS Setup Utility 43 P1197E 861 User s Manual e
Download Pdf Manuals
Related Search