Home

Model E1010 Indicator User Instructions

1. L isolatore NON DEVE essere installato nel cavo di rete flessibile in dotazione con l unit Impianto elettrico note In condizioni di bagnato la spina deve essere collegata al circuito terminale aggiuntive in caso di condizioni di derivazione tramite un apposita presa concepita per applicazioni di di bagnato lavaggio Per gli impianti negli Stati Uniti occorre utilizzare un coperchio conforme alla specifica e un dispositivo di tenuta a prova di pioggia come quelli prodotti da Leviton Questi consentono il collegamento dell unit con un coperchio a prova di pioggia montato su presa che consente di soddisfare la classificazione NEMA 38 secondo quanto richiesto dal codice nazionale per il materiale elettrico nell articolo 410 57 Si noti che il coperchio menzionato elencato nel file UL E13397 Per gli impianti in Europa occorre utilizzare una presa che fornisca almeno una protezione IP56 per il complesso spina cavo Assicurarsi che il grado di protezione fornito dalla presa sia adatto per l ambiente 1 31 Manutenzione di routine Per evitare la possibilit di scosse elettriche o danni alla macchina spegnere sempre la macchina e isolarla dall alimentazione elettrica prima di eseguire gli interventi di manutenzione di routine Per evitare il rischio di caduta della macchina laddove applicabile assicurarsi che sia posizionata in modo sicuro su una superficie piana e orizzontale Model E1010 Indicator User Instructio
2. Model E1010 Indicator User Instructions Specifications Power requirements Excitation Analog Signal Input Range Analog Signal Sensitivity Calibration Operational keys Operational annunciators Display Analog to digital conversion rate Unit of measure Capacity selections Incremental selections Programmable selections Time and date RAM Internal resolution Standard inputs Model E1010 User Instructions 100 240 Volts AC 600 mA 50 60 Hz Optional Internal battery 23 hours of continuous operation with one weight sensor 15 hours of continuous operation with four weight sensors Standby mode extends battery life 5 volts Supports up to four 350 ohm weight sensors 12 mV V 0 5 uV division minimum 2 to 5 points stored Tare Select Zero Print Units F1 Clear Mode Escape Enter On Off 0 9 numeric and decimal point Center of Zero Motion Gross Tare Net Battery status Under Target Over Units of measure LB KG Custom unit Peak Print OP1 OP2 OP3 Count Preset Tare Seven digit seven segment 0 8 inch high Lighted STN Transmissive Display rate Selectable 1 2 5 10 60 times per second Three independently programmable units of measure Pounds Kilograms Custom 999 999 with decimal located from zero to five places Multiples and sub multiples of 1 2 5 Zero range motion detection automatic zero tracking five point linearization Battery backed up real time cl
3. PRINT Press the UNITS key to scroll through the available units of measure while in normal operating mode Units are enabled in a password protected menu Contact your local supplier or Avery Weigh Tronix distributor for UNITS assistance Also acts as a right arrow key when in the menu structure Press the Flkey to select application specific choices Also used to access PLU Product Look Up memory channels Press the IMODE key to scroll through the enabled applications The application name is briefly displayed when key is released Press the C CE key to clear entries CE Press the ESCkey to escape a function or return to ESC normal operation mode Press and hold to access the password display for the menus m zZ m A Press the ENTERkey to accept displayed choices Model E1010 Indicator User Instructions 27 Front Panel 28 Use the numeric keypad to enter values For example entry Setpoint target entry Preset tare entry Password entry To turn the unit on press and hold the ONOFF key until the display turns on To turn the unit off press and hold the ON OFF key until the unit turns off There are annunciators that are located around the display window These provide information on indicator function Each is described below Center of zero annunciator gt 0 A Motion annunciator da Gross weight annunciator Net weight annunciator ne Tare annunciator Battery level annun
4. device Monitor the output to see that it is turning on and off 23 Stop the test by pressing the SELECT key OUT 1 is displayed 24 Press the UNITS key OUT 2is displayed 25 Repeat steps 21 and 22 for outputs 2 and 3 At step 21 use the TARE or UNITS key to scroll to the desired output 26 Press the SELECT key OUTPUT is displayed This completes the TEST menu item Press the SELECT key to go to TEST then press the UNITS key to go to the AUDIT submenu or press ESC to return to normal weighing mode The next section of the Supervisor menu is the AUDIT submenu This menu lets you view configuration and calibration audit counters These counters cannot be changed only viewed They are a record of configurations and calibrations performed on the indicator Follow these steps to access each item in the AUDIT submenu 1 With AUDIT displayed press the PRINT key CFG is displayed This stands for the Configuration audit counter Use this item to see how many times this indicator has been configured 2 Press the PRINT key A number is briefly displayed then CFG is displayed This is the number of times this indicator has been configured 3 Press the UNITS key CALis displayed This stands for the Calibration audit counter Use this item to see how many times this indicator has been calibrated 4 Press the PRINT key A number is briefly displayed then CAL is displayed This is the number of times thi
5. 60950 Nota Questa dichiarazione valida solamente se lo strumento di pesatura non automatico stato verificato dal produttore o provvisto di un certificato di conformit rilasciato da un ente riconosciuto Se richiesta disponibile una copia del certificato originale firmato presso Avery Weigh Tronix Foundry Lane Smethwick West Midlands B66 2LP England Avery Weigh Tronix A TT CE Declaraci n de Conformidad Fabricante Avery Weigh Tronix Tipo E1005 E1010 Numero del certificado de homologaci n CE UK2723 conforme a las exigencias de las siguientes directivas CE Directiva para equipos de pesaje 90 384 EEC no autom ticos Directiva CEM 89 336 EEC Directiva de baja tensi n 73 23 EEC Las normas armonizadas en vigor son EN 45501 EN 61000 4 EN 55022 EN60950 Nota Esta declaraci n es v lida solamente si el equipo de pesaje no autom tico ha sido verificado por el fabricante o con certificado de conformidad emitido por un organismo notificado Una copia del certificado de homologaci n que corresponde a este equipo se puede obtener en Avery Weigh Tronix Foundry Lane Smethwick West Midlands B66 2LP England Contents page Contents nennen iten 11 Safety and Warnings Dessen 13 Installatie en service Dutch 15 Installation et Service French 17 In
6. E1010 Indicator User Instructions The mains lead must be connected to a supply outlet with a protective earth contact The electrical supply at the socket outlet must provide over current protection of an appropriate rating For your protection all mains 110V or 230V equipment used out of doors or in wet or damp conditions should be supplied from a correctly fused source and protected by an approved ground fault protection device RCD GFCI etc IF IN DOUBT SEEK ADVICE FROM A QUALIFIED ELECTRICIAN Pluggable equipment must be installed near an easily accessible socket outlet Permanently connected equipment must have a readily accessible disconnect device incorporated in the fixed wiring An isolator or circuit breaker with at least 3mm contact separation The isolator MUST NOT be installed into the flexible mains cable supplied with the unit Under wet conditions the plug must be connected to the final branch circuit via an appropriate socket receptacle designed for wash down use Installations within the USA should use a Rain tight while in use specification grade cover such as those manufactured by Leviton These allow the unit to be plugged in with a rain tight cover fitted over the plug receptacle allowing it to meet a NEMA 3R rating as required by the national electrical code under section 410 57 Note that the particular cover mentioned is listed in UL file E13397 Installations within Europe must use a socke
7. RECOMMAND PAR LE CONSTRUCTEUR METTRE REBUT LES BATTERIES USAG ES CONFORMEMENT AUX INSTRUCTIONS DU FABRICANT CAUTION THE POWER SUPPLY CORD IS USED AS THE MAIN DISCONNECT DEVICE ENSURE THAT THE SOCKET OUTLET IS LOCATED INSTALLED NEAR THE EQUIPMENT AND IS EASILY ACCESSIBLE ATTENTION LE CORDON D ALIMENTATION EST UTILIS COMME INTERRUPTEUR G N RAL LA PRISE DE COURANT DOIT TRE SITU E OU INSTALL E PROXIMIT DE L QUIPEMENT ET ETRE FACILE D ACC S Avery Weigh Tronix ES CE Declaration of Conformity Manufacturer Avery Weigh Tronix Type E1005 E1010 No of EC type approval certificate UK 2723 corresponds to the requirements of the following EC directives Non Automatic Weighing 90 384 EEC Instruments Directive EMC Directive 89 336 EEC Low Voltage Directive 73 23 EEC The applicable harmonised standards are EN 45501 EN 61000 4 EN 55022 EN 60950 Note This declaration is only valid if the non automatic weighing instrument was verified by the manufacturer or with a certificate of conformity issued by a notified body A copy of the original signed declaration for this instrument is available from Avery Weigh Tronix Foundry Lane Smethwick West Midlands B66 2LP England Avery Weigh Tronix A TT CE Verklaring van Overeenstemming Fabrikant Avery Weigh Tronix Type E1005 E1010 Nummer van de Verklaring van EG typeg
8. and RX lines pins 2 and 3 as shown in illustration at left When the port you want to test is displayed press the PRINT key With the pins jumpered if the wiring and hardware are operating correctly PASS will be displayed If there is a problem FAIL will be displayed and you should contact a service representative Press SELECT key to exit the serial test SERIAL is displayed Press the UNITS key INPUT is displayed This will test remote input switches connected to the indicator Press the PRINT key to access the test 123is displayed 1 stands for input 1 etc Activate any remote switches connected to the indicator to verify hardware and wiring The display will show the input number change to ifthe external switch is operating properly Press the SELECT key to exit the test INPUT is displayed 41 Menu Mode OUTPUT Output test CAUTION Follow all lockout and red tag procedures Disconnect all devices not intended to start before running this test AUDIT Audit counters CFG Configuration audit counter CAL Calibration audit counter 42 20 Press the UNITS key OUTPUT is displayed This is the output test item See note at left 21 Press the PRINT key to access the test OUT 1 is displayed This stands for output 1 22 Press the PRINT key The display toggles between ON and OFF This will toggle the output off and on Use a Trips Interface Unit TIU3 or other output
9. la m quina aseg rese de colocarla adecuadamente sobre una superficie lisa y nivelada 1 39 Limpieza de m quina El exterior de los productos est ndares se puede limpiar con un pa o limpio humedecido con agua conteniendo una peque a cantidad de detergente suave No se deben usar abrasivos duros disolventes estropajos o soluciones de limpieza alcalinas tales como soda c ustica especialmente en las pantallas de visualizaci n En ning n caso debe intentar limpiar el interior de la m quina No rocie ning n l quido directamente a las pantallas de visualizaci n Si utiliza un fluido de limpieza espec fico aseg rese que lo roc a al pa o y no a la pantalla 1 40 Formaci n No intente operar o llevar a cabo ning n procedimiento en la m quina si no AA ha recibido la capacitaci n apropiada 0 leido los Libros de Instrucci n Para evitar el riesgo de LTR lesi n de la tensi n repetida es importante asegurarse que la m quina sea colocada en una superficie ergon micamente satisfactoria para el usuario En casos de un uso prolongado se les recomienda descansos frecuentes a los operarios 1 41 Objetos afilados No utilice objetos afilados destornilladores u as largas etc para teclear 1 42 Conformidad de ESD La siguiente advertencia se puede aplicar a su m quina ADVERTENCIA Esto es un producto de clase A En un ambiente dom stico este producto puede causar interferencias radiof nicas
10. moet worden ge nstalleerd in de buurt van een goed te bereiken wandcontactdoos Apparatuur die permanent op een contactdoos is aangesloten moet in de vaste bedrading zijn voorzien van een goed te bereiken scheidingsschakelaar Een isolatieschakelaar of stroomonderbreker met een minimale contactscheiding van 3 mm De isolatieschakelaar MAG NIET worden ge nstalleerd in de met de installatie meegeleverde flexibele netstroomkabel Onder natte omstandigheden moet de stekker op het eindtakcircuit worden aangesloten met een contactdoos dat geschikt is voor contact met water Installaties in de VS moeten gebruik maken van een Rain tight while in use specification grade cover zoals die worden gemaakt door Leviton Hierdoor kan de apparatuur worden aangesloten met een waterdicht deksel dat over de stekker contactdoos wordt geplaatst Zo voldoet de installatie aan NEMA 3R zoals vereist in de national electrical code sectie 410 57 Het betreffende deksel is vermeld in UL reg E13397 Installaties in Europa moeten gebruik maken van een stopcontact dat minimaal IP56 bescherming biedt aan de stekker kabelassemblage Men dient ervoor te zorgen dat de door de contactdoos geboden mate van bescherming geschikt is voor de omgeving 1 10 Periodiek onderhoud Model E1010 Indicator User Instructions Schakel de apparatuur altijd uit en haal deze uit de contactdoos voordat u periodiek onderhoud pleegt om het risico van een elektrische s
11. zijn WAARSCHUWING Dit is een klasse A product In huiselijke omgeving kan dit product radiostoring veroorzaken in welk geval de gebruiker de noodzakelijke maatregelen dient te nemen 16 Model E1010 Indicator User Instructions 1 15 Installation et Service French 1 15 Installation et Service French CET EQUIPEMENT NE CONTIENT AUCUN COMPOSANT PERMETTANT L INTERVENTION TECHNIQUE DE L UTILISATEUR L installation et la maintenance de cet quipement doivent tre ex cut es uniquement par du personnel sp cifiquement form et habilit intervenir 1 16 Installation lectrique Equipement avec prise secteur Equipement connect en permanence Consignes d isolement Installation lectrique Information suppl mentaire pour conditions d humidit Le c ble d alimentation doit tre branch sur une prise quip e d un dispositif de masse mise la terre L alimentation lectrique au niveau de la prise doit assurer une protection d une valeur appropri e contre une surcharge de courant Par mesure de s curit tous les quipements fonctionnant sous 110 ou 230 V utilis s en ext rieur ou dans des conditions d humidit doivent tre raccord s une source avec un coupe circuit et prot g par un appareil homologu de protection contre les d fauts de masse normes RCD GFCI etc EN CAS DE DOUTE DEMANDER L AVIS D UN TECHNICIEN QUALIFIE Ces quipements lectriques doivent tre install s pr
12. 1 User Menu 1 Access the User menu by pressing and holding the ESC key for 3 5 seconds PASS is displayed FA E 3 m 1 A E 2 Key in the User menu password 111 and press ENTER GG rat PRINT A UNITS TEST is displayed 3 Press the PRINT key ABOUT is displayed Press the PRINT key then the UNITS key to view the part number and revision level for the software found in your indicator Press SELECT key to return to ABOUT 4 Press the UNITS key DISP is displayed This is the display test item Press the PRINT key to perform a dynamic test of the display Press ESC key to stop the dynamic test 54 Model E1010 Indicator User Instructions jumper Serial port connector Model E1010 Indicator User Instructions 10 11 12 13 Press the UNITS key BUTTON is displayed This is the button test item Press the PRINT key to perform a button test Each key you press will be reflected on the display by a name or numbers to confirm the button is functioning correctly See KEY DISPLAY below The ESC key is excluded from this test Use it to stop the testing and return to the BUTTON menu item KEY DISPLAY TARE tArE SELECT SELECt ZERO ZEro PRINT Print UNITS Units F1 F1 Power on oFF 7 777 8 888 9 999 4 444 5 555 6 666 1 111 2 222 3 333 0 dP C CE CE MODE nnodE ENTER Enter ESC EScis briefly displayed before exiting the test Press E
13. 2 23 24 25 26 27 28 29 Press the SELECT key ACC is displayed Press the UNITS key BATCH is displayed Press the PRINT key PRINT is displayed Use this item to print out a complete report of batch information Press the ENTER key Display shows BUSY briefly then returns to PRINT Press the UNITS key TYPE is displayed Use this item to set the type of the batching application to Automatic or Manual AUTO In this mode you start the batch by pressing the F1 key Output 1 activates and OPT annunciator lights When the weight reaches the configured cutoff value output 1 turns off Output 2 automatically activates and OP2 lights to continue the batch This pattern repeats through output 2 and 3 MAN In manual mode the user presses F1 to start the batching process As each output weight is met the output deactivates and the user must press the F1 key to activate each subsequent output Press the PRINT key The current type setting is displayed Toggle between the choices by pressing the TARE or UNITS key Press the ENTER key when your choice is displayed TYPE is displayed Press the UNITS key CLEAR is displayed Use this item to clear all the information stored for this application WARNING Only do this if you are sure you want the information permanently removed You may want to print out the report before clearing all the information Press the ENTER key S
14. 350 ohm weight sensor and 15 hours with four 350 ohm weight sensors Recharge time from complete discharge is 14 hours while powered up and in service single loadcell The AC power supply AC mains supply will charge the battery as it powers the indicator Battery life conservation can be configured through the indicator s Supervisor menu See Supervisor Menu on page 34 You can set the sleep timer to OFF 1 2 hour two hours or four hours Use the OFF setting If the battery is not installed Model E1010 Indicator User Instructions PLU Product Look Up Memory Channels If there are preset tares in the This indicator has 10 channels of memory called PLU or Product Look Up PLUs you cannot enter a keyboard Each channel can contain the following information or pushbutton tare Preset tares Channel are enabled and entered under the 0 Supervisor Menu on page 34 Tare If preset tares are not enabled any Gross Accum tare you enter by keyboard or Net Accum pushbutton method will be active Total for all PLUs TARGET OP1 TARGET OP2 TARGET OP3 Lower Limit Upper Limit Count Accum Piece Weight Peak Weight 1 To activate or recall a PLU key in the desired channel number 0 9 and press the F1 key The PLU channel is active Any of the items listed above that have values are activated Any values that are listed above that change while this PLU is active are stored ie accumulator count etc 2 PLU channels can
15. 56031 USA Tel 507 238 4461 Fax 507 238 4195 Email industrial weigh tronix com www wtxweb com Avery Weigh Tronix UK Foundry Lane Smethwick West Midlands England B66 2LP Tel 44 0 870 903 4343 Fax 44 0 121 224 8183 Email info awtxglobal com www averyweigh tronix com Avery Weigh Tronix
16. Annunciators are OFF TIU3 Relays are OFF After activation by recipe Outputs are ON Annunciators are ON TIU3 Relays are ON 50 This section applies if your indicator has the batching application active The batching application allows you to set three outputs based on three progressively larger weights There are two possible modes of batching Auto or Manual Each are explained below AUTO As weight is added to the scale and the first output point is reached OP1 annunciator lights and Output 1 is activated When weight reaches the second cutoff OP2 annunciator lights and Output 2 activates When weight reaches the third cutoff OP3 annunciator lights and Output 3 activates MANUAL In manual mode after you begin the batching process you must press the F1 key to activate each subsequent output after each output weight is reached Normal Operation Mode Press and hold SELECT key for 3 5 seconds op Key in output 1 value and press ENTER to accept or ESC to move to the next ouput OP2 Key in output 2 value and press ENTER to accept or ESC to move to the next ouput OP3 Key in output 3 value and press ENTER to accept or ESC to return weigh mode Press ESC key when done Figure 8 3 Output flowchart Follow these steps and the flowchart in Figure 8 3 to setup a recipe with three ingredients 1 With the indicator powered up press and hold the F1 key until OPI is displayed 2 Press the PRINT key to set th
17. Avery Weigh Tronix ES Model E1010 Indicator E1010 User Instructions ENGLISH 43092 0017A e1 April 21 2006 1 1 11 1 E1010 rev2006 u book Avery Weigh Tronix LLC 2006 rights reserved The information contained herein is the property of Avery Weigh Tronix Inc and is supplied without liability for errors or omissions No part may be reproduced or used except as authorized by contract or other written permission The copyright and the foregoing restriction on reproduction and use extend to all media which the information may be embodied Avery Weigh Tronix is a trading name of Weigh Tronix Inc Trademarks and acknowledgements Avery Weigh Tronix Avery Berkel Dillon NCI and Salter Brecknell are registered trademarks in certain jurisdictions All third party brands and product names used within this document are trademarks or registered trademarks of their respective holders IMPORTANT When programming or configuring the equipment you must ensure that you comply with all relevant standards and legislation The example settings given in this book may not be legal for trade with the public Declarations of compliance United States This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipmen
18. ESC key to abort the save process or press the ENTER key to clear all the information CLEAR is displayed Press the SELECT key COUNT is displayed Press the UNITS key TOP is displayed Use this item to clear and print reports for the peak application Press the PRINT key PRINT is displayed Use this item to print out a complete report of peak application information Press the ENTER key Display shows BUSY briefly then returns to PRINT Press the UNITS key CLEAR is displayed Use this item to clear all the information stored for this application WARNING Only do this if you are sure you want the information permanently removed You may want to print out the report before clearing all the information Press the ENTER key SURE is displayed Press the ESC key to abort the save process or press the ENTER key to clear all the information CLEAR is displayed Press the SELECT key repeatedly until SETUP is displayed This concludes the Application section of the Supervisor menu 1 Enter the Supervisor men and press the UNITS key repeatedly until TEST is displayed This menu lets you view indicator information and test the scale the display keypad serial port inputs and outputs Press the PRINT key ABOUT is displayed Press the PRINT key then the UNITS key to view the part number and revision level for the software found in your indicator Press SELECT key to return to ABOUT P
19. Italian 1 29 Installazione e manutenzione Italian L APPARECCHIATURA NON CONTIENE COMPONENTI RIPARABILI DALL UTENTE L installazione e la manutenzione dell apparecchiatura devono essere eseguite esclusivamente da personale addestrato e autorizzato 1 30 Impianto elettrico Il cavo di alimentazione deve essere collegato ad una presa di corrente con un contatto di messa a terra protettiva La fornitura elettrica alla presa di corrente deve prevedere una protezione contro le sovracorrenti di un indice appropriato Per sicurezza l apparecchiatura di rete 110 V o 230 V utilizzata all aperto oppure in condizioni di bagnato o umidit deve essere alimentata da una sorgente opportunamente equipaggiata con fusibili e protetta da un dispositivo approvato di protezione contro i guasti di terra come ad esempio un dispositivo di corrente residua RCI un interruttore del circuito di rilevamento di fughe a terra GFCI ecc IN CASO DI DUBBI RIVOLGERSI AD UN ELETTRICISTA QUALIFICATO Apparecchiatura collegabile L apparecchiatura collegabile deve essere installata in prossimit di una presa elettrica facilmente accessibile Apparecchiatura cablata L apparecchiatura collegata in modo permanente deve disporre di un permanentemente requisiti dispositivo di disconnessione facilmente accessibile incorporato nel dell isolatore cablaggio fisso un isolatore o un interruttore salvacircuito con una separazione dei contatti di almeno 3 mm
20. NT key TYPE1 is displayed Dates styles are listed below along with number you enter to create that style 1 MM DD YY e 2 MM DD YYYY e 3 DD MM YY 4 DD MM YYYY Using the TARE and or UNITS key scroll to the number for the style you want to use in all dated reports and press the ENTER key nn XX is displayed nn stands for month XX is the current value Key in the month number 1 for Jan 2 for Feb etc and press the ENTER key DD XX is displayed DD stands for day and XX represents the current value Key in the date value and press the ENTER key YY XX is displayed YY stands for year and XX represents the current value Key in the year 04 2004 etc and press the ENTER key DATE is displayed Enter the Supervisor menu DATE is displayed Press the UNITS key HOUR is displayed Use this item to set the time Press the PRINT key TYPE1 is displayed Type 1 is 24 hr military format Type 2 is 12 hour AM PM format Use the TARE and or UNITS key to scroll to the number for the style you want to use in all time stamped reports and press the ENTER key HH XX is displayed This stands for hour and its current value See note at left Key in the hour in military time and press the ENTER key nn XX is displayed nn stands for minute and XX represents the current value Key in the minutes and press the ENTER key SS XX is displayed SS stands for seconds and XX represents the current va
21. Press the ENTER key when your choice is displayed TYPE is displayed 5 Press the UNITS key CLEAR 5 displayed Use this item to clear all the information stored for this application WARNING Only do this if you are sure you want the information permanently removed You may want to print out the report before clearing all the information 6 Press the ENTER key SURE is displayed 7 Press the ESC key to abort the save process or press the ENTER key to clear all the information CLEAR is displayed 8 Press the SELECT key TARGET is displayed COUNT 1 Press the UNITS key Counting Application COUNT is displayed Use this item to clear and print reports for the count application 2 Press the PRINT key PRINT is displayed Use this item to print out a complete report of count application information 3 Press the ENTER key Display shows BUSY briefly then returns to PRINT 4 Press the UNITS key CLEAR 5 displayed Use this item to clear all the information stored for this application WARNING Only do this if you are sure you want the information permanently removed Model E1010 Indicator User Instructions 39 Menu Mode TOP Peak Weight Application TEST submenu Test menu ABOUT Indicator information ADC Analog to Digital converter 40 You may want to print out the report before clearing all the information Press the ENTER key SURE is displayed Press the
22. SC key to stop the button test BUTTON is displayed Press the UNITS key SERIAL is displayed This is the serial port test item Press the PRINT key PORTI is displayed Use the TARE or UNITS keys to toggle between Port 1 and Port 2 To test the communications port jumper the TX and RX lines pins 2 and 3 as shown in illustration at left When the port you want to test is displayed press the PRINT key With the pins jumpered if the wiring and hardware are operating correctly PASS will be displayed If there is a problem FAIL will be displayed and you should contact a service representative Press SELECT key twice to exit the serial test SERIAL is displayed 55 Indicator Diagnostics Audit counters cannot be reset 56 14 15 16 17 18 19 20 21 Press the SELECT key TEST is displayed Press the UNITS key AUDIT is displayed Press the PRINT key CFG is displayed This stands for the configuration audit counter Press the PRINT key to see the number of times the configuration has been altered on this indicator After a few seconds CFG is displayed Press the UNITS key CAL is displayed This stands for the calibration audit counter Press the PRINT key The number of times the indicator has been calibrated is displayed After a few seconds CAL is displayed Press the ESC key The display returns to normal operation mode This completes the User menu
23. URE is displayed Press the ESC key to abort the save process or press the ENTER key to clear all the information CLEAR is displayed Press the SELECT key BATCH is displayed Press the UNITS key TARGET is displayed Use this item to print and clear reports for the checkweigher application and to set the type of sampling to be used Net or Sample Press the PRINT key Model E1010 Indicator User Instructions PRINT is displayed Use this item to print out a complete report of checkweigher information 3 Press the ENTER key Display shows BUSY briefly then returns to PRINT 4 Press the UNITS key TYPE is displayed Use this to set the way you set the target weight for the checkweighing application You have two choices LIMIT and SPL sample LIMIT You enter the upper and lower limits for your item and the indicator will use those values to run the checkweighing graph on the top center of the display This setting allows an Accept range Each segment of the fan graph will equal one division SPL This method allows the user to place a correct weight product on the scale to set the target weight The indicator will use this weight to run the display Upper and lower limits will automatically be 1 division above and below the target weight respectively Each colored display graduation is equal to 1 scale division The TARGET light stays lit Toggle between the choices by pressing the TARE or UNITS key
24. achine v rifier qu elle soit plac e sur une surface plane et niveau 17 Safety and Warnings 1 18 Nettoyage de l appareil L ext rieur des produits standard peut tre nettoy avec un chiffon propre humidifi avec de l eau et une petite quantit de d tergent Ne pas utiliser de d tergents abrasifs ou de solutions alcalines telle que la soude m nag re surtout sur les crans Ne jamais essayer de nettoyer l int rieur de la machine Ne jamais vaporiser de liquide directement sur l cran En cas d utilisation d un liquide de nettoyant m nager asperger le chiffon et non l cran 1 19 Formation Ne pas essayer d utiliser la machine ou suivre une proc dure quelconque sans avoir re u la formation appropri e ou avoir lu les manuels d utilisation Pour viter le risque de microtraumatismes r p t s il est important de s assurer que la machine soit plac e sur une surface ergonomiquement satisfaisante pour l utilisateur Il est recommand que l utilisateur fasse des pauses fr quentes en cas d une utilisation prolong e 1 20 Objets tranchants Ne pas utiliser d objets tranchants tournevis ongles trop longs pour actionner les touches 1 21 EMC L avertissement suivant pourrait concerner votre appareil Attention Ceci est un appareil de classe A Dans un environnement domestique cet appareil peut tre la cause d interf rences radio Dans ce cas l utilisateur peut tre oblig de pre
25. ak weight is displayed and the center of zero annunciator lights 4 To clear the peak value press the F1 key 0 is displayed 5 Repeat steps 2 4 for other weighments Use the SELECT key to scroll through G T N and peak values You can use the outputs function if so desired while in the Peak Weighing application Follow these steps to setup the outputs 1 With the indicator powered up press and hold the SELECT key until OP1 is displayed 2 Press the PRINT key to see a value entry screen Press the PRINT key to accept the displayed value or key in anew value and press the ENTER key to accept OP2will be displayed 3 Repeat for the other outputs You can skip the displayed output by pressing the ESC key 4 After OP3 has been set or skipped the indicator will automatically return to normal weighing mode 51 Communications and Printing Communications and Printing The default serial port parameters are 9600 baud 8 databits no parity and 1 stop bit 22 The E1010 provides two RS 232 outputs for data transmission to peripheral devices Contact your local supplier or Avery Weigh Tronix distributor for assistance with RS 232 interface connections If your indicator has a peripheral device connected from the gross net weighing mode press the PRINT key to transmit the configured print formats The PRINT annunciator will illuminate while data is transmitted and the data configured to be printed will be outpu
26. and press the ENTER key BUSY is briefly displayed followed by one of two possible displays a the sample met the minimum sample requirements the display will show the correct number of parts on the scale b If the sample size was not large enough the display will show ERROR and then how many more parts to add to the scale For example 5 might be displayed Add the number requested wait for the scale to stabilize then press ENTER again The display will read the correct number of parts on the scale Place the parts on the scale to be counted You can use the outputs function if so desired while in the Counting application Follow these steps to setup the outputs 1 With the indicator powered up press and hold the SELECT key until OP1 is displayed Press the PRINT key to see a value entry screen Press the PRINT key to accept the displayed value or key in anew value and press the ENTER key to accept OP2 will be displayed Repeat for the other outputs You can skip the displayed output by pressing the ESC key After OP3 has been set or skipped the indicator will automatically return to normal weighing mode 49 Indicator Operations 8 6 Batch Weighing This indicator has a 10 channel PLU Product Look Up memory To access a memory channel press a number from to 9 then press the F1 key Configuring Outputs Output operation in batching mode Before activation by recipe Outputs are OFF
27. anismo de desconexi n accesible incorporado en el cableado de la instalaci n el ctrica Un aislador o interruptor del circuito con una separaci n minima del contacto de 3mm NO SE DEBE instalar el aislador dentro del cable de red flexible facilitado con la m quina Bajo condiciones de humedad se debe conectar el enchufe directamente al suministro de corriente por medio de una toma de corriente adecuada e impermeable Instalaciones en los EEUU deber n proveer de una cubierta con grado de especificaci n Impermeable mientras en funcionamiento como aquellas fabricadas por Leviton Esto permite que la unidad sea enchufada con una cubierta impermeable colocada sobre el enchufe permitiendo cumplir con el grado NEMA 3R seg n es requerido por el c digo nacional el ctrico bajo la secci n 410 57 Aviso La cubierta mencionada est listada en el archivo UL n mero E13397 Instalaciones en Europa deben usar una toma de corriente que provea un minimo de protecci n de IP56 a la conexi n de enchufe cable Hay que asegurarse de que el grado de protecci n realizado por el enchufe corresponde a las exigencias del entorno 23 Safety and Warnings 1 38 Mantenimiento rutinario Para evitar la posibilidad de un choque el ctrico o da os a la m quina siempre apague la m quina y descon ctela del suministro el ctrico antes de realizar cualquier operaci n rutinaria de mantenimiento Para evitar el riesgo de ca da de
28. are activated through the password protected menu Checkweighing allows a quick visual check of the acceptability or unacceptability of an item s weight You can set your target weight in one of two ways The mode is set in the password protected Supervisor menu See the Supervisor Menu on page 34 for instructions The two modes are explained below Limit Mode Enter the upper and lower limits for your item and the indicator will use those values to run the display See Figure 8 1 Lower limit Upper limit TRE al u Ju Each graduation 1 division Figure 8 1 Limit mode Sample Mode Place a correct weight product on the scale and press the F1 key The indicator will use this weight to run the display Upper and lower limits will automatically be 1 division above and below the target weight respectively Figure 8 2 shows how the graphic display works in Sample mode Each graduation is equal to 1 scale division The TARGET light stays lit if weight is 1 division of the target weight TARGET n TARGET aall WE JT Each graduation 1 division Figure 8 2 Sample Mode 47 Indicator Operations Limit Mode Entering Upper and Lower Limits Sample Mode Using Product to Set Target Weight Performing a Checkweighing Weighment Using Outputs Output operation in checkweighing mode Outputs are OFF in gross zero band Annunciators are OFF TIU3 Relays are OFF Outputs latch on for approp
29. asse A In un ambiente domestico questo prodotto pu causare interferenze radio e in tal caso possibile che l utente debba intraprendere misure adeguate Model E1010 Indicator User Instructions 1 36 1 36 Instalaci n y Mantenimiento Spanish Instalaci n y Mantenimiento Spanish 1 37 EL EQUIPO NO TIENE PARTES QUE PERMITEN UN MANTENIMIENTO POR EL USUARIO La instalaci n y el mantenimiento del equipo s lo pueden ser realizados por el personal calificado y autorizado Instalaci n el ctrica Para garantizar su seguridad todo el equipo conectado a la red 110V o 230V que se utiliza en el exterior o bajo condiciones de humedad debe ser alimentado por una fuente con fusibles adecuados y protegida por un dispositivo de protecci n contra la p rdida de tierra aprobado RCD GFCI etc EN CASO DE DUDA CONSULTE UN T CNICO CALIFICADO Equipo conectado Equipo conectado permanentemente Requisitos de aislador Instalaci n el ctrica avisos adicionales para condiciones de humedad Model E1010 Indicator User Instructions El cable de electricidad debe ser conectado a un enchufe con toma de tierra La alimentaci n el ctrica en el enchufe debe estar provista de una protecci n adecuada de sobrecorriente Todo el equipo que se puede conectar a la red el ctrica se debe instalar cerca de una toma de corriente f cilmente accesible Si el equipo est permanentemente conectado debe existir un mec
30. be cleared by using a password protected menu These instructions are found in the Supervisor Menu on page 34 You can also print a report of all the PLU channels in the same password protected menu Model E1010 Indicator User Instructions 31 Entering an ID Number Entering an ID Number You can enter an ID number which is then part of the active PLU channel To enter an ID you must be in weighing mode Key in a number on the keypad then press the ENTER key This number will be assigned to the currntly active PLU 22 Model E1010 Indicator User Instructions Menu Mode 7 1 User Menu The E1010 has two menus you can use to set up and test the indicator the User menu and the Supervisor menu Both are explained below Press the ESC key to exit the menu Model E1010 Indicator User Instructions Use the User menu to do the following e Audit the number of configurations and calibrations performed See software information Display test Button test Serial port test 1 Access the User menu by pressing and holding the ESC key for 3 5 seconds PASS_ is displayed 2 Key in the User menu password 111 and press the ENTER key Figure 7 1 shows the User menu items Use the keys shown in the dotted box in Figure 7 1 to navigate through the menu and choose the items you want Normal Operation Mode Press and hold ESC for 3 5 seconds BHBGE WAN Key in 111 and press ENTER Software Display Button v
31. chok of beschadiging van de apparatuur te voorkomen Zorg dat de apparatuur zich altijd op een vlak en effen oppervlak bevindt om te voorkomen dat deze op de grond valt 15 Safety and Warnings 1 11 Het apparaat reinigen De buitenkant van de standaardproducten kan met een schone vochtige doek met een klein beetje mild reinigingsmiddel worden afgenomen Gebruik geen schuurmiddelen oplosmiddelen schuurpoeder of alkalische reinigingsmiddelen zoals soda om het apparaat te reinigen Gebruik deze middelen in elk geval nooit op de displayvensters De binnenkant van het apparaat mag nooit worden gereinigd Gone Spuit geen vloeistof direct op het displayvenster Als u een schoonmaakmiddel in een spuitbus gebruikt spuit het middel op de doek en niet op het displayvenster 1 12 Training Tracht geen procedure op de machine uit te voeren behalve wanneer u de AA relevante training gehad of de instructieboeken gelezen heeft Om RSI Repetitive Strain Injury letsel door repetitieve werkzaamheden te voorkomen is het belangrijk ervoor te zorgen dat het apparaat op een werkoppervlak wordt geplaatst dat ergonomisch voldoet voor de gebruiker In gevallen van lang gebruik adviseren wij regelmatig een pauze in te lassen 1 13 Scherpe voorwerpen Gebruik geen scherpe voorwerpen schroevendraaiers lange vingernagels etc om de toetsen te bedienen 1 14 EMC naleving De volgende waarschuwing kan op uw apparaat van toepassing
32. ciator If the unit is powered by AC this FO annciator will be lit EZA Peak weight annunciator Print annunciator lights when data is being sent to an external Print device Custom unit of measure annunciator Preset tare annunciator This blank annunciator will light when an accumulation is Blank rectangle occurring Output 1 annunciator lights when the output 1 is active There are annunciators for Output 2 and 3 also Model E1010 Indicator User Instructions Model E1010 Indicator User Instructions Piece Count Total kb Iin EEEN ul Piece weight annunciator lights when the piece weight in a counting application is displayed Count annunciator lights when count is displayed in the counting application Total annunciator lights when displaying the total count in the accumulator application Unit of measure annunciator shows the current unit of measure Checkweighing annunciator lights during use of the checkweiging application 29 Battery Information Battery Information When the indicator goes to sleep you must press the ON OFF switch to restart the indicator 30 This unit may contain a sealed rechargeable 6 volt 3 0Ah lead acid battery Life expectancy of this battery is 3 5 years in standby use or e 180 charging cycles approx if discharged 100 e 400 charging cycles approx if discharged 50 e 1200 charging cycles approx if discharged 30 Battery life is 23 hours with one
33. dual weighments gross and net and stores the totals These totals can be recalled at any time and the number of weighments included in the totals can be displayed With the proper password all information can be deleted See the PLU Product Look Up on page 36 The accumulator maximum is 999 999 It does not rollover to start over at 0 To use the accumulator power up the unit and follow these steps 1 Empty the scale and press the ZERO key to zero the display is displayed and gross and center of zero annunciators are lit 2 Place item on the scale Weight is displayed 45 Indicator Operations Using Outputs Output operation in accumulation mode Below Configured Value Outputs are ON Annunciators are OFF TIU3 Relays are ON Above Configured Value Outputs are OFF Annunciators are ON TIU3 Relays are OFF 46 You can press the PRINT or F1 key to add weight to the accumulator If you press PRINT the weight is accumulated and the information printed If you press F1 the weight is accumulated Scale weight must return to a weight within the configured gross zero band before another weighment can be accumulated Repeat 2 and 3 for each weighment you want to accumulate To review the accumulator total and the number of weighments remove all weight from the scale the scale must read weight and press the SELECT key repeatedly 1st press Net weight displayed 2nd press Tare weight displayed 3
34. e value for the output Key in a value and press the F1 key to accept the value OP2 will be displayed You can scroll through all three outputs by using the TARE and UNITS keys 3 Press the UNITS key OP2 is displayed 4 Repeat steps 2 and 3 for each output Press ESC key to return to normal operation with the ingredients active Indicator will automatically return to normal weighing mode after OP3 value is entered Model E1010 Indicator User Instructions 8 7 Peak Weighing 8 7 Peak Weighing This indicator has a 10 channel PLU Product Look Up memory To access a memory channel press a number from 0 to 9 then press the F1 key Using Outputs Output operation in peak mode Below Configured Value Outputs are ON Annunciators are OFF TIU3 Relays are ON Above Configured Value Outputs are OFF Annunciators are ON TIU3 Relays are OFF Model E1010 Indicator User Instructions This section applies if your indicator has the Peak application active Peak weight is defined as the highest stable weight reached by the scale Momentary higher weights that do not stabilize are ignored While in Peak mode the Peak annunciator remains lit Follow these steps to perform a peak weighment 1 Empty the scale and press the ZERO key to zero the display is displayed 2 Place the item s on the scale Weight is displayed 3 After the motion annunciator turns off remove the item s from the scale The pe
35. eferte flexible Netzkabel installiert werden Im Freien oder unter feuchten Bedingungen muss der Stecker direkt ber eine geeignete abwaschbare Steckdose an die Stromversorgung angeschlossen werden Anschl sse in den USA sollten mit einer Abdeckung mit dem Spezifikationsgrad Wasserundurchl ssig w hrend in Betrieb versehen sein wie beispielsweise die von Leviton Dadurch kann das Ger t an eine Steckdose mit einer wasserdichten Abdeckung laut NEMA 3R angesteckt werden wie dies nach dem National Electrical Code Abschnitt 410 57 erforderlich ist Hinweis die genannte Abdeckung ist unter UL E13397 aufgelistet Anschl sse in Europa m ssen ber eine Steckdose erfolgen die die Mindest Anforderungen der IP56 Schutzvorkehrung f r Stecker Kabel anschl sse erf llt Es muss darauf geachtet werden dass der von der Steckdose gew hrleistete Schutz den Anforderungen des entsprechenden Umfelds entspricht 1 24 Regelm ige Wartung Model E1010 Indicator User Instructions Zum Schutz vor Stromschl gen und um Besch digungen des Ger tes vorzubeugen muss dieses vor der Durchf hrung von Wartungs arbeiten ausgeschaltet und vom Netz getrennt werden Um das Herunterfallen des Ger tes zu vermeiden sollte dieses sicher auf einer ebenen und waagerechten Oberfl che platziert werden 19 Safety and Warnings 1 25 Reinigung des Ger tes 1 26 Schulung Das Geh use kann von au en mit einem feuchten Tuch ger
36. einigt werden Dem Wasser kann eine kleine Menge eines milden Reinigungsmittels beigef gt werden Zu Reinigungszwecken besonders im Fall von Monitoren d rfen keine Scheuermittel L sungsmittel oder andere alkalische Reinigungsmittel verwendet werden Die Innenseite des Ger tes darf unter keinen Umst nden nass gereinigt werden Spr hen Sie keine Fl ssigkeiten direkt auf das Display Wenn Sie eine Reinigungsfl ssigkeit verwenden spr hen Sie diese auf ein Tuch und nicht auf das Display RA Ohne Durchlesen der Bedienungsanleitung bzw einer Einweisung durch das Fachpersonal sollte das Ger t nicht bedient oder ein Verbundsystem in Betrieb genommen werden Um Fehlbelastungen zu vermeiden sollte die Waage so platziert werden dass sie den ergonomischen Anspr chen des Bedieners gerecht wird Es wird empfohlen bei lang andauernder Bedienung des Ger tes regel m ige Pausen einzulegen 1 27 Spitze Gegenst nde 1 28 EMV gerecht Verwenden Sie keine spitzen Gegenst nde Schraubenzieher lange Fingern gel usw um die Tasten zu bedienen Der folgende Warnhinweis trifft unter Umst nden auf Ihr Ger t zu WARNUNG Bei diesem Ger t handelt es sich um ein Ger t der Klasse A Dieses Ger t kann bei einem Betrieb in Wohngegenden Funkst rungen verursachen Ist dies der Fall muss der Benutzer eventuell entsprechende Ma nahmen treffen Model E1010 Indicator User Instructions 1 29 Installazione manutenzione
37. en cuyo caso podr a ser necesario que el usuario adopte medidas adecuadas 24 Model E1010 Indicator User Instructions Introduction The Model E1010 is an easy to use uncomplicated indicator for general weighing applications It is ideal for bench scales floor scales and tank weighing applications The display includes a multi segment fan graph for fast visual awareness for checkweighing The indicator can perform counting functions peak weight functions act as a remote display and operate on battery power optional You can switch between enabled applications with one key press The indicator also has 10 PLU Product Look Up memory channels for storing data Two communication ports allow connection to a printer remote display or computer The indicator also has three setpoint controls and can accommodate a footswitch for zero print or tare function All this in an NEMA 6 4X rated enclosure 2 1 About This Manual Major sections of this manual are numbered and headed by titles in a black bar like Introduction above Subheadings appear in the left column Instructions and text appear on the right side of the page Occasionally notes tips and special instructions appear in the left column 2 2 Setup Your indicator will be installed by a qualified Avery Weigh Tronix distributor They will make the required connections to your scale and peripheral devices 1 With the unit plugged in see note at left press and hold
38. enabled using a password protected menu Contact your local supplier or Avery Weigh Tronix distributor for assistance with the password protected menu Also see SETUP submenu Setup menu on page 36 in this manual for configuring a specific application If multiple applications are enabled you can switch between them by pressing the MODE key The display will briefly show the application name when you press the MODE key The general weighing application comes as the default application You can do gross weighments and tare net weighments Below are instructions for each To change unit of measure press the UNITS key 44 To perform gross weighing power up the unit and follow these steps 1 Empty the scale and press ZERO key to zero the display Ois displayed and gross and center of zero annunciators are lit 2 Place item to be weighed on the scale Weight is displayed Model E1010 Indicator User Instructions 8 2 General Tare Net Weighing 8 2 General Tare Net Weighing You can key in a known tare weight Key in the value and press the TARE key The scale weight must be at zero before you can key in a known tare weight Using Outputs Output operation in general weighing mode Below Configured Value Outputs are ON Annunciators are OFF TIU3 Relays are ON Above Configured Value Outputs are OFF Annunciators are ON TIU3 Relays are OFF To perform a net weighment power up the unit and follow these
39. ersion test test and revision Pass Fail Pass Fail Figure 7 1 User menu Specific instructions on the User menu appear in the section ndicator Diagnostics later in the manual 33 Menu Mode 7 2 Supervisor Menu The Supervisor menu is shown in Figure 7 2 Use this menu to set time and date print and clear reports perform diagnostic tests and view audit counters WARNING Entering this menu and changing settings may affect operation of the indicator and may require a service call to correct Be sure you want to change settings before doing so Normal Operation Mode Press and hold ESC for 3 5 seconds H EP NY E KO Key in 1793 and press ENTER EE Software Displays Display Button version mV V test test and revision Port Pass Fail Pass Fail Cal Prints prms on ae a prints Prints report Figure 7 2 Supervisor Menu Date Type0 lt lt I ao ao 34 Model E1010 Indicator User Instructions Password for the Supervisor menu is 1793 DATE submenu Set date HOUR submenu Set time Time must be entered in 24 hour military time Model E1010 Indicator User Instructions Access the Supervisor menu by pressing and holding the ESC key for 3 5 seconds PASS is displayed Key in the password 1793 and press ENTER DATE is displayed Use this to set the current date Press the PRI
40. from the target weight Repeat step 1 for all products of this weight The output function in the checkweigher mode functions differently than in the other applications The outputs are controlled by the over under and accept values OP1 activates and its annunciator illuminates when the under condition is present OP2 activates and its annunciator illuminates when the accept condition is present OP3 activates and its annunciator illuminates when the over condition is present Model E1010 Indicator User Instructions 8 5 Counting 8 5 Counting This indicator has a 10 channel PLU Product Look Up memory To access a memory channel press a number from 0 to 9 then press the F1 key Using Outputs Output operation in counting mode Below Configured Value Outputs are ON Annunciators are OFF TIU3 Relays are ON Above Configured Value Outputs are OFF Annunciators are ON TIU3 Relays are OFF Model E1010 Indicator User Instructions This section applies if your indicator has the counting application active Applications are activated through a password protected service menu Follow these steps to perform a counting function with the E1010 1 4 In gross weight mode press the F1 key PCS is displayed followed by an underscore cursor Enter the sample size you desire see note at left and press ENTER Add X is displayed X is the sample size you keyed in Place the correct number of parts on the scale
41. ion sign e pour cet appareil est disponible l adresse suivante Avery Weigh Tronix Foundry Lane Smethwick West Midlands B66 2LP England Avery Weigh Tronix A TT Konformit tserkl rung Hersteller Avery Weigh Tronix Typ E1005 E1010 Nr der EU Bauartzulassung UK2723 entspricht den Anforderungen folgender EU Richtlinien Waagenrictlinie f r 90 384 EWG nichtselbstt tige Waagen EMV Richtlinie 89 336 EWG Niederspannungsrichtlinie 73 23 EWG Die angewendeten harmonisierten Normen sind EN 45501 EN 61000 4 EN 55022 EN 60950 Anmerkung Diese Erkl rung gilt nur wenn die nichtselbstt tige Waage vom Hersteller geeicht wurde oder in Verbindung mit einer Konformit tsbescheinigung einer benannten Stelle Eine Abschrift der original unterschriebenen Konformit tserkl rung ist unter untengenannter Adresse erh ltlich von Avery Weigh Tronix Foundry Lane Smethwick West Midlands 866 2LP England Avery Weigh Tronix a TT Dichiarazione di conformit Produttore Avery Weigh Tronix Tipo E1005 E1010 N certificato di approvazione UK2723 CE conforme alle caratteristiche previste dalle seguenti direttive CE Normativa per satrumenti di 90 384 CEE pesatura non automatici Normativa EMC 89 336 CEE Normativa per la bassa tensione 73 23 CEE Le norme standard armonizzate EN 45501 EN 61000 4 applicate sono EN 55022 EN
42. lue 35 Menu Mode SETUP submenu Setup menu APP Applications PLU Product Look Up Printed PLU Information Channel ID Tare Gross Accum Net Accum Total TARGET OP1 TARGET OP2 TARGET OP3 Lower Limit Upper Limit Count Accum Piece Weight Peak Weight 36 Key in the seconds and press the ENTER key HOUR is displayed Enter the Supervisor menu DATE is displayed Repeatedly press the UNITS key until UNITS is displayed Use this item to set the time From previous step 6 press the UNITS key SETUP is displayed Use this submenu to print and or clear application reports and choose the operation modes or values for applications which have choices Each is explained in the following steps Reference Supervisor Menu on page 34 Press the PRINT key APP is displayed Each application is listed below this menu item Applications are enabled and disabled in a password protected menu but you do each application s configuration under this menu item Contact your local supplier or Avery Weigh Tronix distributor for assistance with the password protected menu Press the PRINT key PLU is displayed This stands for Product Look Up There are 10 PLU memory channels numbered 0 9 Each channel contains all the parameter values and accumulator totals associated with allthe different applications This menu item lets you print out the information shown in the list at left set a tare fo
43. ndre les mesures ad quates 18 Model E1010 Indicator User Instructions 1 22 1 22 Installation und Wartung German Installation und Wartung German DAS GER T ENTH LT KEINE TEILE DIE VOM BENUTZER GEWARTET WERDEN KONNEN Die Installation und Wartung des Ger tes darf nur von geschultem und autorisiertem Personal durchgef hrt werden 1 23 Elektrische Installation Zu Ihrer eigenen Sicherheit sollten alle Netzstrom betriebenen 110V oder 230V Ger te die im Freien oder unter feuchten Bedingungen verwendet werden von einer gesicherten Stromquelle die ber eine zugelassene Fehlerstrom Schutzeinrichtung Fl Schalter gesch tzt ist versorgt werden IN ZWEIFELSF LLEN WENDEN SIE SICH BITTE AN EINEN QUALIFIZIERTEN ELEKTRIKER Angeschlossene Ger te Elektrische Installation Zusatz Hinweise bei nassem Umfeld Die verwendete Steckdose muss unbedingt mit einem Schutzleiter ausgestattet sein Die Stromversorgung ber die Steckdose muss durch einen vorschriftsm igen Fehlerstrom Schutzschalter gesch tzt sein Ans Netz angeschlossene Ger te m ssen leicht vom Netz trennbar sein St ndig angeschlossene Ger te Trennschalter AnforderungenDauerhaft angeschlossene Ger te m ssen ber einen leicht zug nglichen in den festen Stromkreis integrierten Notschalter verf gen Einen Trenn schalter oder Sicherungsautomaten mit mindestens Kontakt Trennung Der Trennschalter DARF NICHT in das mitgeli
44. ns 21 Safety and Warnings 1 32 Pulizia della macchina 1 33 Formazione La parte esterna dei prodotti standard pu essere pulita con un panno pulito inumidito con acqua contenente una piccola quantit di detergente neutro Non utilizzare sostanze abrasive corrosive solventi detergenti sgrassanti e soluzioni detergenti a base alcalina come ad esempio carbonato di sodio particolarmente sui display Non tentare mai di pulire l interno della macchina Non spruzzare alcun liquido direttamente sui display Se si utilizza un apposito liquido detergente assicurarsi di spruzzare il liquido su un panno e non sul display QI 1 34 Oggetti appuntiti Non tentare di azionare la macchina o non eseguire alcun intervento su di questa a meno che non si riceva una formazione appropriata o senza aver letto il manuale di istruzioni Per evitare lesioni derivanti da sollecitazioni ripetitive RSI Repetitive Strain Injury importante assicurarsi che la macchina venga posta su una superficie che sia posizionata in modo soddisfacente da un punto di vista ergonomico per l utente Si consiglia di effettuare frequenti interruzioni durante l uso prolungato Non utilizzare oggetti appuntiti cacciaviti unghie lunghe ecc per azionare le chiavi 1 35 Conformit alla direttiva sulla compatibilit elettromagnetica EMC Per la macchina possibile che sia applicabile la seguente avvertenza AVVERTENZA questo un prodotto di cl
45. ock and RAM 64 424 509 counts per mV V per sec Three logic level inputs for Zero Print Tare Units F1 57 Specifications Standard outputs Serial outputs Serial Command Inputs Self diagnostics Circuitry protection Options Operating applications Operating temperature Enclosure Dimensions Weight Agencies and Approvals 58 Three cutoff outputs open collector design Two serial ports RS 232 RS 422 RS 485 20mA current loop RS 232 Programmable serial response to ASCII character input SMA protocol broadcast enquire RDj 4100 E Series remote display Display keys inputs outputs serial ports RFI EMI and ESD protection Trips Interface Unit TIU3 General weighing simple counting checkweighing accumulation peak measurement batching and remote display If enabled switchable from front panel 14 to 104 F 10 to 40 C approved 4 to 140 F 20 to 60 C non legal 10 to 90 noncondensing humidity Stainless steel NEMA 6 4X 9 25 W x 9 25 H x4 5 D 23 5cm W x 23 5cm H x 11 4cm D without mounting bracket 9 75 W x 11 H x 7 D 24 8cm W x 28cm H x 17 8cm D with mounting bracket 11 Ib 5 kg NTEP CC 04 029 Class III IIIL 10 000 divisions OIML Cert No R76 1992 GB1 04 09 Class 10 000 divisions Canadian Weights and Measures pending UL CUL CE marked Model E1010 User Instructions Avery Weigh Tronix USA 1000 Armstrong Dr Fairmont MN
46. oedkeuring UK2723 is in overeenstemming met de voorschriften van de volgende EG richtlijnen Richtlijn Niet automatische 90 384 EEG Weegwerktuigen Richtlijn EMC 89 336 EEG Richtlijn Laagspanning 73 23 EEG Toegepaste geharmoniseerde normen EN 45501 EN 61000 4 EN 55022 EN60950 Noot Deze verklaring is alleen geldig indien het weegwerktuig door de fabrikant is geverifieerd of met een Verklaring van Overeenstemming afgegeven door een bevoegde instantie Een kopie van de originele ondertekende verklaring is verkrijgbaar door contact op te nemen met Avery Weigh Tronix Foundry Lane Smethwick West Midlands B66 2LP England Avery Weigh Tronix ES CE D claration de Conformit Fabricant Avery Weigh Tronix Type E1005 E1010 No de certificat d approbation de type CE UK2723 correspond aux exigences des directives CE suivantes Directive pour les instruments de 90 384 CEE pesage fonctionnement non automatique Directive CEM 89 336 CEE Directive Basse Tension 73 23 CEE Les normes harmonis es applicables sont EN 45501 EN 61000 4 EN 55022 EN 60950 Nota Cette d claration est valide seulement si l instrument de pesage fonctionnement non automatique a t v rifi par le fabricant ou avec une attestation de conformit d livr e par un organisme notifi Une copie originale de la d clarat
47. oose OFF TARE is displayed With PLU tares disabled the user can enter keyboard or pushbutton tares during normal weighing operations Press the UNITS key CLEAR 5 displayed Use this item to clear all the information stored for each PLU WARNING Only do this if you are sure you want the information permanently removed You may want to print out the reports before clearing all the information Press the PRINT key SURE is displayed Press the ESC key to abort the save process or press the ENTER key to clear all the information CLEAR is displayed Press the SELECT key PLU is displayed Press the UNITS key ACC is displayed This stands for the accumulator application Press the PRINT key PRINT is displayed Use this item to print out a complete report of accumulator totals Press the ENTER key Display shows BUSY briefly then returns to PRINT Press the UNITS key CLEAR 5 displayed Use this item to clear all the information stored for this application WARNING Only do this if you are sure you want the information permanently removed You may want to print out the report before clearing all the information Press the ENTER key SURE is displayed Press the ESC key to abort the save process or press the ENTER key to clear all the information CLEAR is displayed 37 Menu Mode BATCH Batch Application TARGET Checkweighing application 38 19 20 21 2
48. quent breaks are taken during prolonged usage 1 6 Sharp objects Do not use sharp objects screwdrivers long fingernails etc to operate the keys 1 7 EMC compliance The following warning may be applicable to your machine WARNING This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures 14 Model E1010 Indicator User Instructions 1 8 Installatie en service Dutch 1 8 Installatie en service Dutch DE APPARATUUR BEVAT GEEN VOOR EEN SERVICEBEURT IN AANMERKING KOMENDE ONDERDELEN Installatie en onderhoud van de apparatuur mag alleen worden uitgevoerd door getraind en bevoegd personeel 1 9 Elektrische installatie Op een contactdoos aan te sluiten apparatuur Permanent bedrade apparatuur Vereisten voor isolatieschakelaar Elektrische installatie aanvullende opmerkingen voor natte omstandigheden De netstroomkabel moet worden aangesloten op een geaarde contactdoos De stroomvoorziening op de contactdoos moet overstroombeveiliging van een toelaatbaar vermogen bieden Voor uw veiligheid moet alle in open lucht of onder natte of vochtige omstandigheden gebruikte netstroomapparatuur 110 V of 230 V zijn voorzien van een goedgekeurde aansluitingsbescherming RCD GFCI enz BIJ TWIJFEL DIENT ADVIES TE WORDEN GEVRAAGD AAN EEN GEKWALIFICEERDE ELEKTRICIEN Op een contactdoos aan te sluiten apparatuur
49. r each of the PLU channels and or clear the information Press the PRINT key PRINT is displayed Use this item to print out a complete report of all application parameters and totals Press the ENTER key to print the report Display shows BUSY briefly then returns to PRINT The report will be printed to your connected external device Press the UNITS key TARE is displayed This item enables or disables the use of preset tares With PLU tares enabled you cannot enter keyboard or pushbutton tares PLU tares and the other tares are mutually exclusive per NTEP rules Use the TARE or UNITS key to toggle between the ON and OFF choices Press the PRINT key when your selection is displayed If you choose ON go to step 9a If you choose off skip to step 9b If you choose ON PLU Ois displayed See note at left Press the PRINT key A numeric entry screen is displayed Model E1010 Indicator User Instructions ACC Accumulator Application Model E1010 Indicator User Instructions 9b 10 11 12 13 14 15 16 17 18 Key in a tare value for PLU 0 and press ENTER to accept it OR Scroll to any PLU you want by using the TARE or UNITS key press the PRINT key and then key in the tare value and press ENTER to accept it The PLU number is shown Repeat scrolling to a PLU and entering a value until you are finished then press SELECT TARE is displayed If you ch
50. rd press Gross total of all weighments is displayed 4th press Net total of all weighments is displayed 5th press Number of weighments is displayed 6th press Active PLU number is displayed 7th press Display returns to gross weigh mode You need the supervisor s password to clear the accumulator You can use the outputs function if so desired while in the Accumulator application Follow these steps to setup the outputs 1 With the indicator powered up press and hold the SELECT key until OP1 is displayed Press the PRINT key to see a value entry screen Press the PRINT key to accept the displayed value or key in anew value and press the ENTER key to accept OP2 will be displayed Repeat for the other outputs You can skip the displayed output by pressing the ESC key After OP3 has been set or skipped the indicator will automatically return to normal weighing mode Model E1010 Indicator User Instructions 8 4 Checkweighing 8 4 Checkweighing This indicator has a 10 channel PLU Product Look Up memory To access a memory channel press a number from 0 to 9 then press the F1 key The graph is based off of net weight so if a tare is active only the net weight is considered for checkweighing If there is no tare gross weight is used as the basis for the graph Model E1010 Indicator User Instructions This section applies if your indicator has the checkweighing application active Applications
51. ress the UNITS key ADC is displayed This stands for the analog to digital converter value in mV Vs Model E1010 Indicator User Instructions DISP Display test BUTTON Key test SERIAL Serial port test jumper Serial port connector INPUT Input test Model E1010 Indicator User Instructions 10 11 12 13 14 15 16 17 18 19 Press the PRINT key The mV V value coming into the indicator from the scale is displayed You can use the ZERO key to zero the mV V reading The scale can then be tested for function and linearity Press the SELECT ADC is displayed Press the UNITS key DISP is displayed This is the display test item Press the PRINT key to perform a dynamic test of the display This allows you to see any damaged areas of the display which may require a display replacement Press the ESC key to stop the dynamic test Press the UNITS key BUTTON is displayed This is the keypad button test item Press the PRINT key to perform a button test Each key you press will be reflected on the display screen to confirm the button is functioning correctly Press the ESC key to stop the button test BUTTON is displayed Press the UNITS key SERIAL is displayed This is the serial port test item Press the PRINT key PORTI is displayed Use the TARE or UNITS keys to toggle between Port 1 and Port 2 To test communications port jumper the TX
52. riate ABOVE OVER and ACCEPT Annunciators are ON TIU3 Relays are ON 48 Follow these steps to setup and use the checkweigher function if limit mode is enabled where you set upper and lower weight limits Press the Fi key Up is displayed followed by an underscore cursor Key in the upper weight limit Press the F1 key Lo is displayed Key in the lower weight limit Press the F1 key The indicator returns to normal weigh mode Place items on the scale and the display will show if the weight is over under or acceptable based on the limits you have set Follow these steps to setup and use the checkweigher function if sample mode is enabled where you set target weight based on an actual product 1 Place a sample of the correct weight on the scale Weight is displayed Press the F1 key The target weight is captured the indicator switches to net mode the display reads and your indicator is ready to use as 8 checkweigher The target weight will be the same as your sample item and the target will stay lit whenever an item s weight is within 1 division of the target weight With your target weight set as described in one of the previous two sections place your item on the scale If the weight equals the acceptable value the TARGET annunciator lights If the weight varies from the target value upper or lower segments may be lit and the weight will show a plus or minus weight reading for the deviation
53. s d une prise facilement accessible Les quipements qui doivent tre aliment s en permanence doivent tre dot s d un syst me de d connexion facilement accessible et int gr au c blage un circuit isolant ou coupe circuit avec une s paration de contact d au moins 3 mm Le circuit isolant ne doit pas tre install dans le c ble flexible fourni avec l appareil Dans des environnements humides la fiche d alimentation doit tre connect e une prise ou bo tier sp cialement con u et prot g contre les jets d eau Les installations effectu es aux tats Unis doivent utiliser un couvercle imperm able tel que ceux fabriqu s par Leviton Ce couvercle class NEMA 3R permet de prot ger l appareil et la prise conform ment au code national lectrique section 410 57 Remarque le couvercle mentionn ci dessus est r pertori dans le fichier UL E13397 Pour les installations en Europe il est n cessaire d utiliser au minimum une connexion aux normes IP56 pour la prise la fiche secteur et le cable Veiller ce que la protection fournie par le point de connexion soit adapt e l environnement 1 17 Maintenance de routine Model E1010 Indicator User Instructions Avant toute maintenance de routine pour viter toute possibilit de choc lectrique ou de dommage l appareil teindre toujours la machine et la d connecter de l alimentation secteur Pour viter tout risque ventuel de chute de la m
54. s indicator has been calibrated 5 Press the SELECT key AUDIT is displayed Model E1010 Indicator User Instructions SLEEP Sleep mode When the indicator goes to sleep you must press the ON OFF switch to restart the indicator Any motion or any key press restarts the sleep timer Model E1010 Indicator User Instructions 1 Press the UNITS key SLEEP is displayed This stands for the sleep mode timer 2 Press the PRINT key Current sleep timer value is shown Scroll through the choices 1 2 2 4 or OFF by pressing the TARE or UNITS key Choose OFF to disable sleep mode Choose any of the other values to enable a sleep mode after the chosen time of keyboard inactivity and no scale motion 3 Press ENTER when choice is displayed SLEEP is displayed This completes the Sleep item and the Supervisor menu 4 Press ESC to save and return to normal weighing operation 43 Indicator Operations Indicator Operations When the indicator goes to sleep you must press the ON OFF switch to restart the indicator This indicator has a 10 channel PLU Product Look Up memory To access a memory channel press a number from 0 to 9 then press the F1 key 8 1 General Weighing The E1010 comes equipped with several weighing applications e General weighing default setting e Accumulator weighing Batch weighing e Checkweigher Counting Peak capture Remote display These applications are
55. stallation und Wartung German ss 19 Installazione e manutenzione Italian 21 Instalaci n y Mantenimiento Spanish renner enneeeevennenenneeerenn 23 Introduction ie thetic alia a 25 Front Panel dl 26 Battery Information sise 30 PLU Product Look Up Memory Channels i 31 Entering an ID Number sise 32 Men iMode tnt edelen as et 33 Indicator Operations cnn arc cnn rana rn 44 General Tare Net Weighing narran rana 45 Gheckweighingi ansa ias 47 61618 181616 A e a iii el i 49 Batch Welghing ur sillaba isa agi 50 Peak Welghing cputisciilonia iii 51 Communications and Printing issus 52 Error Messages ina ei SR 53 Indicator Diagnostics nes siate 54 Specification 57 Model E1010 User Instructions 11 12 Model E1010 User Instructions Safety and Warnings 1 1 Installation and service English THE EQUIPMENT CONTAINS NO USER SERVICEABLE COMPONENTS Installation and maintenance of the equipment must only be carried out by trained and authorized personnel 1 2 Electrical installation Pluggable equipment Permanently wired equipment Isolator requirements Electrical installation supplementary notes for wet conditions Model
56. steps 1 Empty the scale and press ZERO key to zero the display is displayed and gross and center of zero annunciators are lit 2 Place item to be tared on the scale Weight is displayed 3 Press the TARE key 0 is displayed and net annunciator is lit 4 Place material to be weighed on the scale Net weight of material is displayed and net annunciator is lit 5 Repeatedly press the SELECT key to scroll through gross tare and net values Remove the weight from the scale and press TARE to return to gross mode You can use the outputs function if so desired while in the general weighing application Follow these steps to setup the outputs 1 With the indicator powered up press and hold the SELECT key until OPI is displayed 2 Press the PRINT key to see a value entry screen Press the PRINT key to accept the displayed value or key in a new value and press the ENTER key to accept OP2 will be displayed 3 Repeat for the other outputs You can skip the displayed output by pressing the ESC key 4 After OP3 has been set or skipped the indicator will automatically return to normal weighing mode 8 3 Accumulator Weighing Press the MODE key to scroll through the enabled applications You can use tare net weighing with the accumulator application The accumulator stores both gross and net totals for later recall Model E1010 Indicator User Instructions The accumulator is memory that collects indivi
57. t is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Canada This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la Classe A prescrites dans le R glement sur le brouillage radio lectrique edict par le minist re des Communications du Canada European Countries WARNING This is a Class A product In a domestic environment this product may cause radio interference in which the user may be required to take adequate measures Caution CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER S INSTRUCTIONS ATTENTION IL Y A DANGER D EXPLOSION S IL Y A REMPLACEMENT INCORRECT DE LA BATTERIE REMPLACER UNIQUEMENT AVEC UNE BATTERIE DU M ME TYPE OU D UN TYPE EQUIVALENT
58. t to the printer Print Format 1 for weighing applications G 1234 56 Ib lt CR gt lt LF gt Print Format 1 for counting application Count 12230 Print Format 1 for peak application 12230 Ib lt CR gt Model E1010 Indicator User Instructions Error Messages 10 The following are displays you may see if problems occur or if invalid operations are attempted with your indicator Display Model E1010 Indicator User Instructions Description Over range weight Under range weight The unit cannot perform a function Displayed only while the key is held down Displayed while a key is pressed when attempting to modify a sealed selection without edit privileges Appears on the display when the E E prom is not functioning correctly Appears on the display when the Analog to Digital converter is not functioning correctly Appears on the display when trying to change something and the scale is sealed 53 Indicator Diagnostics Indicator Diagnostics 1 1 11 1 Indicator Test Functions The user menu lets you test various functions of the indicator The user menu is shown in Figure 11 1 Instructions for using the Test portion of the menu are found below Normal Operation Mode Press and hold ESC for 3 5 seconds PASS _ Q E3 a O UE ZERO 4 gt Key in 111 and press ENTER Serial Software Display Button version test test and revision Pass Fail Pass Fail Figure 11
59. t which provides a minimum of IP56 protection to the plug cable assembly Care must be taken to ensure that the degree of protection provided by the socket is suitable for the environment Safety and Warnings 1 3 Routine maintenance To avoid the possibility of electric shock or damage to the machine always switch off the machine and isolate from the power supply before carrying out any routine maintenance To avoid the risk of the machine falling where applicable ensure that it is placed securely on a flat and level surface 1 4 Cleaning the machine The outside of standard products may be wiped down with a clean cloth moistened with water containing a small amount of mild detergent Harsh abrasives solvents scouring cleaners and alkaline cleaning solutions such as washing soda should not be used especially on the display windows Under no circumstances should you attempt to wipe the inside of the machine Do not spray any liquid directly onto the display windows If you are using a proprietary cleaning fluid ensure you spray the cloth and not the display 1 5 Training Do not attempt to operate or carry out any procedure on a machine unless AA you have received the appropriate training or read the Instruction Books To avoid the risk of RSI Repetitive Strain Injury it is important to ensure that the machine is placed on a surface which is ergonomically satisfactory to the user It is recommended that fre
60. the switch until the display lights up then release the key Attention 2 The indicator powers up in normal operation mode The Model E1010 can be battery powered Charge the battery overnight before using the indicator on battery power only The unit can be run on the AC transformer AC mains power if the battery 5 drained or absent See Battery Information for more information Model E1010 Indicator User Instructions 25 Front Panel Front Panel The front panel shown in Figure 1 consists of the keys and display Peak Print Cust P T P1 OP DU amp 10 F TARE ZERO PRINT UNITS ES Figure 3 1 E1010 front panel 3 1 Keys The functions of the keys on the front panel are listed below Press the TARE key to perform a tare function To key in a known tare weight key in the value and press the TARE key Also acts as a left arrow key when in the menu structure Press the SELECT key to toggle between Gross Tare Net Count Gross Accumulator Net Accumulator Transaction Counter Piece Weight and Peak This is dependent on the current application Press and hold to access the cutoffs trips function Also acts as an up arrow key when in the menu structure 26 Model E1010 Indicator User Instructions Press ZEROkey to zero the scale and display Press the PRINT key to send information to a peripheral device through the Comm port Also acts as a down arrow key when in the menu structure

Model E1010 Indicator User Instructions

Contents

Download Pdf Manuals

Related Search

Related Contents