Home

2007 All Spec Sheets

1. F EES Sates AUSTRALIAN MONITOR e 3 balanced XLR mic dual RCA line inputs e 60 watt output power e 2 Rack units in height e 70 volt or 4 ohm operation e Master treble and bass control e Channel 1 has priority over channels 2 amp 3 defeatable e Facility to add a tone generator module e Tape output pre master e Balanced line output The Australian Monitor Installation Series AMC line of amplifiers takes the heritage amp reliability of our famous AMIS series amp integrates these features into a low cost amplifier format for applications where reliability is everything but the more elaborate features of our AMIS series are not required The 60 watt version of the AMC series is a 2 RU mixer amplifier featuring 70 volt line 100v 230 240V version amp 4 ohm outputs amp 3 universal mic line inputs Master volume amp overall treble bass controls are provided along with Voice triggered muting defeatable giving channel 1 priority over inputs 2 amp 3 There is also facility to internally add a tone generator card Protection includes short circuit and thermal detection and shut down The Australian Monitor AMC series give the contractor a low cost alternative in applications that are cost sensitive but still require a high quality of sound reproduction amp reliability AMC 60 60 Watt 2RU MIXER AMPLIFIER SPECIFICATIONS Power output 60W Outputs 4 Ohms 70 100V THD before cli
2. Active balanced unbalanced Connectors 3 pin XLR 6 35mm TRS balanced RCA unbalanced Impedance 20k Ohms balanced 15k Ohms unbalanced Max level 22dBm level control at centre 3 OUTPUTS Type Active balanced unbalanced Connectors 3 pin XLR 6 35mm TRS balanced RCA unbalanced Impedance lt 150 Ohms Typical Max Level 22dbm 2k ohms 18dBm 600 ohms 4 RFI FILTERS Yes 5 PASSIVE BYPASS SWITCHES Yes 6 OVERLOAD LED SWITCHES 5dB below clipping 7 LOW CUT FILTER AMIS31EQ only 10 250Hz 12dB per octave 8 HIGH CUT FILTER AMIS31EQ only 3kHz 40kHz 12dB per octave 9 FREQUENCY RESPONSE 20Hz 20kHz 10 IM DISTORTION SMPTE 0 005 11 SIGNAL TO NOISE RATIO 94dB 20kHz noise bandwidth 12 CHANNEL SEPARATION 50dB 13 COMMON MODE REJECTION 50 1 14 VOLTAGE 190 250VAC 50Hz 15 DIMENSIONS 1 75 H x 19 01 W x 8 50 D 16 WEIGHT 5 51lbs AMIS 215EQ amp 31EQ ABOUT Australian Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20 years experience in the design and manufacture of audio amplifiers and associated products They are a dynamic corporation priding themselves on excellent customer service better features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide BLS TB La MONITOR AUSTRALIAN MONITOR 2 Way Crossover CHEAP 1 1 i CHARRAN 7 ii z I The Australian Monitor Pro Series AMIS23X
3. a p e Architectural and Engineering Specifications The mixer amplifier shall have four universal input channels each comprising of a balanced microphone input with XLR female sockets and an auxiliary input using dual RCA sockets The 70 volt line speaker outputs should be able to be switched via a six position selector with all call A balanced XLR output to drive additional power amplifiers shall also be provided The amplifier master section shall include one master gain control two EQ controls one with 12dB of cut and boost at 100Hz and the other with 9dB of cut and boost at 10kHz Speaker outputs shall be transformer isolated at 70 volt and 8 ohms The amplifier must be capable of delivering 60 watts RMS into an 80 ohm inductive load with less than 0 5 distortion measured at 1kHz and with system hum and noise less than 74dB The amplifier shall be an Australian Monitor Installation Series model AMIS60 BLE Te Ls MONITOR 4 Input 120 Watt MIXER AMPLIFIER Description The AMIS120 is a 4 channel 120 watt mixer amplifier suitable for rack or desk mounting The amplifier is a self contained compact unit of solid steel construction Inputs The AMIS120 has four universal input channels with separate level controls Each channel will accept balanced or unbalanced microphone line and auxiliary inputs The unit has industry standard XLR microphone sockets and dual RCA auxiliary sockets for each channel An electro
4. for input channels 1 6 Each channel input shall have individual treble and base controls as well as signal present LED indication and 15dB gain trim and phantom power switching The unit shall feature 4 separate LED output indication balanced XLR output separate record output and headphone output Optional tone generator boards muting modules and remote VCA master volume controls must be available The unit shall be an Australian Monitor Installation Series MX81 AUSTRALIAN MO NITOR ABOUT Australian Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20 years experience in the design and manufacture of audio amplifiers and associated products They are a dynamic corporation priding themselves on excellent customer service better features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide BLE Te Ls MONITOR 8 Channel 1 RU MIXER Description The TX8202 is a high performance 8 channel stereo mixer suitable for desk or rack mounting Inputs and Outputs The TX8202 has four active balanced mic line inputs and four stereo line inputs Each channel features recessed treble bass and pan controls Mic Line level can be adjusted per channel via a dip switch All mic and line input connections are via 3 pin XLR female sockets and all stereo line input connections are via dual female RCA sockets Both
5. headroom and a frequency response of no less than 50Hz 15kHz 3dB Total Harmonic distortion shall be no more than 0 1 at 1kHz The S N ratio shall be 74dBV or better Phantom Power of no less than 15V DC shall be available on all microphone inputs An internal switch to disable the phantom power on any of the mic line channels shall also be included The unit shall be packaged in a rugged 1 RU metal chassis suitable for desk or rack mounting The mixer shall be an Australian Monitor Installation Series model TX8202 ABOUT Australian Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20 years experience in the design and manufacture of audio amplifiers and associated products They are a dynamic corporation priding themselves on excellent customer service better features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide ASTRAL MONITOR 120 Watt 70 Volt 8 Ohm AMPLIFIER aie Australian Monito Description The AMIS120P is a 120 watt power amplifier with outputs for 4 and 8 ohms and 70 volt line It may be desk or rack mounted The AMIS120P features a flat screwdriver accessible gain control on the rear panel This amplifier features a status LED Inputs and Outputs The AMIS120P features a balanced line level XLR input with a parallel output to feed additional power amplifiers The unit has industry standard 3 pin XLR microphone s
6. is supplied with an IEC power lead and AM FM antenna The BGM2 also boasts individual stereo outputs from both the Tuners as well as a stereo priority output The BGM2 series provides a high quality rack space friendly and extremely well featured dual background music source at a contractor friendly price BGM_2_DT SPECIFICATIONS AM FM TUNERs FM Tuning Range 87 5 MHz 108 MHz IF Frequency amp Rejection 10 7 MHz gt 80 dB Image Rejection gt 25 dB S N Ratio 1mV M Input 46db T H D ImV lt 1 0 Auto Tuning Sens lt 50uV AM Tuning Range 522kHz 1620kHz IF Frequency amp Rejection 450 kHz gt 45dB Image Rejection gt 30dB S N Ratio 5mV M Input gt 35dB Auto tuning sens lt 2mV Dimensions 18 97 W x 1 73 H x 9 84 D BGMe2 DI INS PTY LTD SYDNEY AUSTRALIA COMMUNICATIONS L S C CE ACN 001 345 482 Architectural and Engineering Specifications The background music source shall be a standard 1RU 19 rack size and comprise dual AM FM tuners Each program source will have a dedicated stereo output as well as a stereo priority output where source two will have priority over source one The unit shall be an Australian Monitor BGM2DT AUSTRALIAN HO NITOR ABOUT Australian Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20 years experience in the design and manufacture of audio amplifiers and associated products They are a dynamic cor
7. price BGMe TCD AUSTRALIAN HO NITOR ABOUT Australian Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20 years experience in the design and manufacture of audio amplifiers and associated products They are a dynamic corporation priding themselves on excellent customer service better features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide Architectural and Engineering Specifications The background music source shall be a standard 1RU 19 rack size and comprise a single MP3 compatible CD player and an AM FM radio tuner Each program source will have a dedicated stereo output as well as a stereo priority output where source two will have priority over source one The CD player shall be programmable up to 20 tracks and shall have infrared control available The unit shall be an Australian Monitor BGM2TCD AVL TR Ls MONITOR Dual Tuner TUNER 1 1 RU dual program source 10 user selectable presets on the AM FM tuner Discrete stereo outputs for each module Priority stereo output as standard Tuner sleep function The Australian Monitor Installation Series BGM2DT program source is a one rack unit dual program source players of radio tuners The tuner modules have one FM band and one AM band with 10 user selectable preset stations there is also a programmable sleep function for the tuner The BGMZ2DT
8. stereo zone outputs Controls There are various levels of control you can use to ensure the optimum result from your ZoneMix3 They include Trim Control for all inputs 5 Stage EQ on each zone output Mic Line Selection for the first two inputs Program Control for selecting a program source via the front panel This can also be done remotely with the ZM3R Remote Source Volume Selection Unit I ZM 3 SPECIFICATIONS Sensitivity for OdB out Mic Line Input RCA 86mV 19dB Mic Line Input XLR 1 55mV 54dB Prog Input RCA 190mV 12dB Max Level Out 10V RMS 22dB Frequency Response 20Hz 20kHz OdB 3dB THD Less than 0 1 Noise 80dB Crosstalk Better than 65dB Phantom Power 15VD Metering and Status A status LED gives an indication of OUTPUT signal It glows green at 30dB and red at OdBV 1V This is meant to indicate clip within the ZoneMix3 When used with Australian MonitorSynergy amplifiers both LEDS on the ZoneMix3 and the Synergy amplifier will go red simultaneously indicating system clip with pot at full on the amplifier A remote LED indicates that the zone is in remote control mode A power LED indicates there is power to the unit Power Input 20VAC 30VA max Dimensions 1 74 x 18 9 x11 2 Weight 5 5lb Shipping 6 6lb AUSTRALIAH MONITOR ABOUT Australian Monitor Corporate Headquarters is located in Sydney Remote Panels and Station
9. the Left and Right outputs are balanced and feature 3 pin male XLR sockets A stereo tape output using dual female RCA sockets is also provided A 1 2 stereo headphone socket is included on the front panel The rear panel includes a terminal block for activation of the optional Tone Generator The first four channels feature a line level direct output which can be used to feed additional amplifiers mixers or recording devices An internal jumper allows the first four inputs to be removed from the master left right outputs while still retaining their direct output function Controls and Metering Front panel controls include Master Left and Right Outputs plus individual channel level controls Each channel also features a recessed screwdriver adjustable treble bass and pan control A four position dip switch mic line phantom power routing is provided for the first four channels A 7 segment LED meter is provided for both the Left and Right Outputs A power on orange LED is part of the LED meter An optional remote master VCA is available for remote master volume control VCA Control The optional VCA control module AMVCA allows the master volume to be remotely controlled External VCA control would normally be via potentiometer connected to a two wire rear panel barrier strip Muting Muting is standard on the unit for channels one and two Both channels have equal priority and will mute channels 3 8 when signal is present The mu
10. to the AMIS standard 1 RU mixer range The MX81 mixer features the new Australian Monitor Standard AMS input section which has an XLR input switchable between mic amp line level dual RCA line inputs on the first 6 inputs only signal present LED indication individually switchable phantom power amp 15dB of gain trim amp treble amp bass controls available per inout The MX81 also boasts whisper quiet operation 4 segment output level indication amp balanced line output record output amp headphone outputs The MX81 has 6xAMS and 2xXLR inputs to one output amp will operate via 110 or 220 240 VAC or 24VDC via an external 24 volt power supply Optional remote VCA volume control tone generators amp muting boards are also available for the MX81 The MX81 mixer is extremely versatile amp represents excellent value for money OPTIONS not included AMMUTE 1 Single Stage Priority Mute Module e Allows for muting of channels 2 and higher when signal is present at channel 1 and the channel volume is turned up AMMUTES Triple Stage Priority Mute Module e Allows for muting of channels 2 and higher when signal is present at channel 1 e Allows for muting of channels 3 and higher when signal is present at channel 2 e Allows for muting of channels 4 and higher when signal is present at channel 3 e Ability to adjust threshold of the trigger signal along with the the release time of the ducked signal AMVCA Remote Master Volume Con
11. years experience in the design and manufacture of audio amplifiers and associated products They are a dynamic corporation priding themselves on excellent customer service better features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide INDICATORS CLOSE LED LED indicates onset of the Expander Gate 8 element GAIN 1 2 4 6 10 15 20 30dB REDUCTION meter POWER SUPPLY Mains Voltages 100 120 200 240 VAC 50 60Hz Power Consumption 9 Watts Fuse 320mA 100 120V slow blow Mains Connection Standard IEC Dimensions HxWxD 1 x 19 x 8 5 Net Weight 6 6 Ibs Shipping Weight 10lbs Multican HA4 4 Channel Headphone Amplifier The Australian Monitor Installation Series HA4 is a high quality low price 4channel stereo headphone amplifier Featuring a stereo 6 35mm jack input amp 4 stereo 6 35mm headphone jack outputs the AMIS HA4 offers separate volume controls per channel amp a simple layout for ease of operation The AMIS HA4 is powered by a supplied 12VDC power supply Juiced Up PPA2 Dual Phantom Power Supply is an in line power supply that provides phantom power for 2 condenser mics selectable between 12VDC amp 48VDC it will power nearly any commercially available microphone The AMIS PPA2 can run off 29 volt batteries or be powered by the supplied 12 VDC power supply Get Up 2 Way Stereo Converter converts consumer level signals to professional level Input will convert a pai
12. zones Each of the 8 output zones is equipped with controls for program selection by means of 4 interlocking push buttons with controls for microphone level program level bass treble and master output level Each zone also has an associated push button to allow any zone the option to be isolated from receiving paging announcements The DigiPage Jr may be powered via AC mains 240 volts or DC 12 24 volts alternate voltages on special order BC ANC a a SPECIFICATIONS Data Digital Audio Mic RJ45 CAT5 Connector Program Sources Trim Max Unbalanced RCA Input Impedance 100KQ Sensitivity 150mV Balanced XLR Input Impedance 1k3Q Sensitivity i1mV 57dbu Min Trim 46dB Local Source Unbalanced RCA Input Impedance 100KQ Sensitivity 1 5V Balanced XLR MIC Input Impedance 1k3Q Sensitivity 11mV Balanced XLR LINE Input Impedance 45KQ Sensitivity 350mV Sum Input Input Sensitivity 330mV Threshold 46dBu at output ind of input Frequency Response 3dB 15Hz 17kHz THD 0 005 Noise Page Mic 84dB Other Inputs 89dB Power Supply 2 4VDC 30VA Plug pack Dimensions H x W x D 5 2 x 19 01 x 6 7 Weight 9 9 Ibs Shipping weight 12 2 Ibs DIGIPAGE JR DPJ88M Paging Station amp Microphone Each DPJ88M microphone station includes 8 zone select buttons with associated zone status LEDs a Zone Page button an All Page button a Clear button and a System Busy
13. 9 W x 11 D Weight 26 5lb Rack Mounting Standard AMIS 120P AUSTRALIAN HO NITOR ABOUT Australian Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20 years experience in the design and manufacture of audio amplifiers and associated products They are a dynamic corporation priding themselves on excellent customer service better features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide Architectural and Engineering Specifications The 120 watt power amplifier shall be designed to run 70 volt line audio systems The unit shall also feature a 4 and 8 ohm output The amplifier may be desk or rack mounted The amplifier must be capable of delivering 120 watts into an 40 ohm inductive load with less than 0 5 distortion measured at 1kKHz and with system hum and noise of 80dB or better Internal current limiting shall protect the amplifier from both overload and overdrive conditions The amplifier shall be an Australian Monitor Installation Series model AMIS120P AVL TR Ls MONITOR 250 Watt 70 Volt 8 Ohm AMPLIFIER dhe Australian Monitor Description The AMIS250P is a 250 watt power amplifier with outputs for 4 ohms and 70 volt line It may be desk or rack mounted The AMIS250P features a flat screwdriver accessible gain control on the rear panel Inputs The AMIS250P features one signal input The unit has industry stan
14. AUSTRALIAN MONITOR Phantom Power ABOUT Phantom Power 18 volts DC is available from all mic inputs A rear panel Australian Monitor phantom power on off dip switch is also provided per channel Gornorae Heacquaner is located in Sydney Australia The organization has more TEIIIITIIII DIG than 20 years experience in the design and manufacture of audio amplifiers and Protection associated products Internal current limiting protects the amplifier from both overload and They are a dynamic overdrive conditions Australian Monitor Installation Series amplifiers feature a protection network that provides greater stability and corporation priding performance Our amplifiers are recognised worldwide for their reliability themselves on excellent and this is due to the extensive levels of current limiting which protect the customer service better amplifiers from both overload and overdrive conditions features and lower priced products for Sound Contractors and Audio ba me mpa E rm pm Wih l fe r TS BS ee W WI H AA Se e as fee Architectural and Engineering Specifications The mixer amplifier shall have eight universal input channels each comprising of a balanced microphone input with XLR female sockets and an auxiliary input using dual RCA sockets A balanced XLR output to drive additional power amplifiers shall also be provided The master output may be controlled remotely via a VCA control An insert point is p
15. BLS TR Lal MONITOR 30 Watt 2RU MIXER AMPLIFIER e 3 balanced XLR mic dual RCA line inputs e 30 watt output power e 2 Rack units in height e 70 volt or 4 ohm operation e Master treble and bass control e Channel 1 has priority over channels 2 amp 3 defeatable e Facility to add a tone generator module e Tape output pre master e Balanced line output The Australian Monitor Installation Series AMC line of amplifiers takes the heritage amp reliability of our famous AMIS series amp integrates these features into a low cost amplifier format for applications where reliability is everything but the more elaborate features of our AMIS series are not required The 30 watt version of the AMC series is a 2 RU mixer amplifier featuring 70 volt line 100v 230 240V version amp 4 ohm outputs amp 3 universal mic line inputs Master volume amp overall treble bass controls are provided along with Voice triggered muting defeatable giving channel 1 priority over inputs 2 amp 3 There is also facility to internally add a tone generator card The Australian Monitor AMC series give the contractor a low cost alternative in applications that are cost sensitive but still require a high quality of sound reproduction amp reliability AMC 30 SPECIFICATIONS Power output 30W Outputs 4 Ohms 70 100V THD before clipping 0 5 Inputs 3x Mic Aux Input connectors 3x XLR RCA Mic sensitivity 1mV 0 2mV AUX sensitivit
16. IR control for the CD player AM FM TUNER up to 20 tracks programmable on the CD player FM Tuning Range 87 5 MHz 108 MHz IF Frequency amp Rejection 10 7 MHz gt 80 dB 10 user selectable presets on the AM FM tuner Discrete stereo outputs for each module Priority stereo output as standard Image Rejection Tuner sleep function gt 25 dB S N Ratio The Australian Monitor Installation Series BGM2TCD program source is aE ian a one rack unit dual program source players of a single disc CD MP3 1mV lt 1 0 players and AM FM tuner The tuner module has one FM band and one Auto Tuning Sens AM band with 10 user selectable preset stations there is also a lt 50uV AM Tuning Range programmable sleep function for the tuner The CD MP3 player is fully 522kHz 1620kHz programmable up to 20 tracks and includes Random track selection IF Frequency amp Rejection for CDs and Repeat single track or Repeat all track functions for both 450 kHz gt 45dB CD and MP3s There is also an optional IR control available for the CD Image Rejection MP3 player N Soa The BGM2TCD is supplied with an IEC power lead and AM FM Misa antenna The BGM2TCD also boasts individual stereo outputs from lt 2mV both the Tuner and CD player as well as a stereo priority output Dimensions 18 97 W x 1 73 H x 9 84 D The BGM2 series provides a high quality rack space friendly and extremely well featured dual background music source at a contractor friendly
17. LED Also included is a gooseneck microphone and microphone sensitivity control A bass cut switch is located on each DPJ88M to reduce booming in high noise areas if required The DPJ88M is housed in an attractive and heavy duty case and may be desk or wall mounted Operation When a page is made a pre announce tone will sound in each of the output zones selected Any program material playing in to the zone s selected will be ducked for the duration of the page Microphone 1 has priority over Microphones s 2 8 Connection DigiPage Jr connects simply by Cat 5 cable The Cat 5 carries the audio and control from the mics to the main DigiPage Jr unit The DPJ88M microphones can be daisy chained for up to 200 meters Bi Ld SS TB La 1 Pa NITOR ABOUT Australian Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20 years experience in the design and manufacture of audio amplifiers and associated products They are a dynamic corporation priding themselves on excellent customer service better features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide AUSTRALIAN MONITOR Description The Australian Monitor ZoneMix3 is an extremely versatile and innovative mixer and signal router Featuring a broadcast quality audio spec the ZoneMix3 allows selection of 4 stereo sources to 3 stereo zones either at the ZoneMix3 or rem
18. LS Input Level Continuously variable Output Level Low High Cont variable CD Boost Rear panel switch mute Front panel switch Channel link Rear panel switch Phase Rear panel switch Dimensions HxWxD 1 75 X19 x6 5 Weight 5 5 Ibs SPECIFICATIONS Input Type RF filtered Servo balances input stage Impedance 60K balanced Nominal Operating Level 10dBu to 4dBu Maximum Input Level 21dBu balanced and unbalanced CMR 1kHz gt 40dB Input detection Type DC de coupled unbalanced input Impedance gt 20K ohms Maximum Input 21dBu Output Type Electronically buffered output stage Impedance lt 40 ohms Bandwidth 5Hz to 50kHz 0 1dB THD 4dBu 0 05 typ IMD SMPTE 10dBu 0 01 typ Noise amp Hum gt 93dBu Crosstalk 20kHz gt 85dBu AMIS 23x amp CL2 COMPRESSOR SECTION Type IKC Interactive Knee Control Compressor Threshold Variable 40 to 20dBu Ratio Variable 1 1 to LIM Attack Variable 0 1 to 200 msec 20dB Release Variable 20 to 20dB GATE SECTION Type IRC interactive Ratio Control Expander Gate Threshold Variable Off to 10dBu DYNAMIC ENHANCER SECTION Type Dynamically Controlled Frequency Correction Process Variable Off to 6 FUNCTION SWITCHES In Out Bypass switch Auto Programme dependent attack and release times AUSTRALIAN MONITOR ABOUT Australian Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20
19. NITOR Zone Paging Mixer CH1 PRIO ern 0 D R seas eae ae IE fh Australian Monitor A INSTALLATION SERIES 456 456 456 456 6 universal inputs 15dB gain trim per input 4 balanced outputs Input 1 has selectable priority Individual output assign with LED Switchable mic line balanced XLR inputs indication per input Bi color status LED per output Bi color status LED per input Remote VCA volume control per output HPF amp 15 VDC Phantom power On board Pre announce bell alert amp evac tones switchable per input 2 stage EQ per input Featuring 6 inputs that can be balanced XLR mic or dual RCA balanced XLR line level all available to any combination of 4 zone outputs Input one can be designated as a paging input with priority over all other inputs individualy selectable at each zone output Front panel switches with LED indication provide for simple routing of each input Each input has bi colour status LED indication amp 2 stage equalization Each input has an internal gain trim which can provide a further 15dB of gain to allow the perfect set up of input gain no matter what the input signal may be Phantom power amp high pass filters are also supplied per input Each balanced XLR zone output also features a dual color status LED amp switchable paging mic priority Remote VCAs are also available for each output allowing for a wall mounted volume control to be installed in remo
20. R Phantom Power ABOUT Phantom Power 18V DC is available from all mic inputs A rear panel Australian Monitor phantom power on off switch is also provided Corporate Headquarters is located in Sydney l Australia The CERREEEFEEAS organization has more aor than 20 years experience air r in the design and mem manufacture of audio amplifiers and ae A e e E FELTIEQELIILIGTZ EEITLIZELIILITL Protection Internal current limiting protects the amplifier from both overload and associated products overdrive conditions Australian Monitor Installation Series amplifiers They aie dynamic feature a protection network that provides greater stability and corporation priding performance Our amplifiers are recognised worldwide for their reliability themselves on excellent and this is due to the extensive levels of current limiting which protect customer service better the amplifiers from both overload and overdrive conditions features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide Paes pM as ater a ae a l ve i ARCHITECTURAL AND ENGINEERING SPECIFICATIONS The mixer amplifier shall have four universal input channels each comprising of a balanced microphone input with XLR female sockets and an auxiliary input using dual RCA sockets The 100V line speaker outputs should be able to be switched via a six position selector with all call A alanced XLR output to d
21. T i TH mn 11 5 AMC 120 MONITOR 120 Watt 2RU MIXER AMPLIFIER ren 4 Ohms 70 100V THD before clipping 0 5 Inputs 3x Mic Aux Input connectors 3x XLR RCA Mic sensitivity e 3 balanced XLR mic dual RCA line inputs 1mV 0 2mV e 120 watt output power AUX sensitivity e 2 Rack units in height ey S N ratio e 70 volt or 4 ohm operation gt 80dBr e Master treble and bass control Bandwidth e Channel 1 has priority over channels 2 amp 3 defeatable On 70V terminals e Facility to add a tone generator module Ea e Tape output pre master tat onipsie e Balanced line output Bass 100Hz 12 dB The Australian Monitor Installation Series AMC line of amplifiers iene ne ere 9 dB takes the heritage amp reliability of our famous AMIS series amp Power source Switchable integrates these features into a low cost amplifier format for 115V 60 Hz applications where reliability is everything but the more elaborate ee Current draw full power features of our AMIS series are not required The 120 watt 25A version of the AMC series is a 2 RU mixer amplifier featuring 70 Fuses volt line 100v 230 240V version amp 4 ohm outputs amp 3 universal nee ae mse Tica S Di mic line inputs 1V Tape Out 300mV Master volume amp overall treble bass controls are provided along aide ommatie with Voice triggered muting defeatable giving channel 1 priority Priority over Mic2 3 over inputs 2 amp 3 There is also facility to intern
22. ally add amp a tone Size l i generator card Protection includes short circuit and thermal ra i i Protections detection and shut down 1 Short circuit 2 Thermal at 95 The Australian Monitor AMC series give the contractor a low cost ae alternative in applications that are cost sensitive but still require a Net Weight high quality of sound reproduction amp reliability 23 1Ib Shipping Dimensions 20 1 W x 5 7 H x 11 7 D Shipping Weight 27 6 b AMC 120 ABOUT Australian Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20 years experience in the design and manufacture of audio AUSTRALIAN MO NITOR 70 Voltage cable run distances to cable type amplifiers and 50m AWG18 associated products 50m 200m AWG13 They are a dynamic Over 200m AWG10 corporation priding 4 Ohm cable run distances to cable type themselves on excellent 10m AWG18 customer service better 10m 30m AWG13 features and lower priced Over 30m Not recommnded products for Sound Contractors and Audio Visual Integrators worldwide a a E Ti iF 1 uE col GIE EEE y 7 Ets oll T Be in Ca a0 ee a i F m P 1EB mm FP dii Giren 11 BLE Ts Ls MONITOR 4 Input 60 Watt MIXER AMPLIFI The AMIS60 is a 4 channel 60 watt mixer amplifier suitable for rack or desk mounting The amplifier is a self contained compact unit of solid steel construction I
23. an Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20 years experience in the design and manufacture of audio amplifiers and associated products They are a dynamic corporation priding themselves on excellent customer service better features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide Hem ey pa cy JH AUSTRALIAN MONITOR Zone Paging System The DigiPage Jr is a matrix switching system allowing any one of up to 8 remote paging microphones DPJ88M to page into any combination of up to 8 output zones over industry standard CAT 5 cable The system also allows any one of up to 4 program inputs to be directed to any or all of the 8 output zones An emergency input is also provided The DigiPage Jr matrix is an attractive slim line 2RU steel cabinet desk or 19 rack mounted It includes inputs for each of the 8 remote DPJ88M microphone stations line level signal and control and a line level output to each of the 8 output zones Also included are inputs for the 4 program sources CD tape tuner etc with associated level trim pots and an input for an emergency signal such as from an EWIS control panel or priority message system Alert and evacuate signal tone generators are connected internally and may be activated remotely by simple contact closure The DigiPage Jr allows for total control over the operation of each of the 8 output
24. and phantom power witching The unit shall feature 4 separate LED output indication balanced XLR output separate record output and headphone output Optional tone generator boards muting modules and remote VCA master volume controls must be available The unit shall be an Australian Monitor Installation Series MX61 AUSTRALIAN MO NITOR ABOUT Australian Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20 years experience in the design and manufacture of audio amplifiers and associated products They are a dynamic corporation priding themselves on excellent customer service better features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide He AUSTRALIAN MONITOR 8 Channel 1 RU MIXER DE a _ Se SSS lt E P Pie E E en ee ee a Ae e r 1 my 1 ta 1 ta i i E 5 ms p a i Pe i aii a if on us IP od ee ifs E a C i i Ti I s i A r a i a a i Fi os uj ay l zi _ TE e 8 input mono mixer e XLR input switchable between mic amp line level e 15dB gain trim control per input e Input 1 is switchable to be pre post master e 24 V DC or mains power operation e Optional remote VCA Tone generator Muting boards e Whisper quiet operation e Dual color signal present indication LED per input The Australian Monitor Installation Series MX81 mixer brings a range of new features
25. ble to be a dedicated priority input individually switchable at each corporation priding output themselves on excellent Two stage EQ will be provided for each input amp all inputs amp outputs will customer service better have bi color status indication The unit shall have onboard pre announce features and lower priced bell Evac amp Alert tones amp have remote VCA master controls for each products for Sound output Contractors and Audio The unit shall be an Australian Monitor ZRM4 Visual Integrators worldwide BGM 2 DCD ALIS TR Ls MONWITOR Output Level 1kHz OdB 1 2V 0 3V Frequency Response 20Hz 20kHz 2dB Separation 1kHz OdB gt 60 dB T H D Noise 1kHz OdB lt 0 05 Dual CD player CDIMP3 PLAYER DeRmics 1 RU dual program source MP3 compatible CD player Option IR control for the CD player up to 20 tracks programmable on the players Discrete stereo outputs for each module Priority stereo output as standard The Australian Monitor Installation Series BGM2DCD program source series is a one rack unit dual program source players of single disc CD MP3 player The CD MP3 player is fully programmable up to 20 tracks and includes Random track selection for CDs and Repeat single track or Repeat all track functions for both CD and MP3s There is also an optional IR control available for the CD MP3 player The BGM2 is supplied with an IEC power lead The BGM2 also has individual stereo out
26. dard 3 pin XLR microphone sockets Two line level sockets are provided for bridged in out connection Outputs The AMIS250P features 70 volt and 4 ohm isolated transformer outputs Protection Internal current limiting protects the amplifier from both overload and overdrive conditions The AMIS250P also features protection in the form of excess temperature auto cut out A built in auto temperature sensing fan will turn on at a factory default level but in most situations will never be required Australian Monitor Installation Series amplifiers feature a protection network that provides greater stability and performance Our amplifiers are recognized worldwide for their reliability and this is due to the extensive levels of current limiting which protect the amplifiers from both overload and overdrive conditions SPECIFICATIONS Power Output 250 Watts RMS Maximum Load 20 Ohms 70 Volts Power Bandwidth 60Hz 17kHz 3dB Frequency Response 60Hz 23kHz 3dB Distortion 0 5 1 kHz rated power THD Signal To Noise Ratio 8 80dB Input Sensitivity 7O0OmV Outputs 70V 4 Ohm Controls One gain control on rear of the unit via flathead screwdriver control Indicators Power on and Protect LED Power Source 120VAC 60Hz 3 pin IEC connector 24VDC Power Consumption 400 Watts Protection Current Limiter protection plus AC and DC fuses Dimensions HWD 3 5 x 19 x 13 Weight 33 1lb Rack Mounting Standard Arc
27. ditional EQ or feedback exterminator may be required Outputs The AMIS250 features 70 volt and 4 ohm isolated transformer outputs plus a tape recorder output by means of dual RCA sockets A balanced 700mV XLR output is also provided to feed up to 6 power amplifiers Tone Generator The AMIS250 comes standard with an in built four tone generator module Tones include Bell Pre announce Chime Alert Tone and Evacuate Tone Any of these tones may be activated from a simple contact closure on the rear panel of the amplifier Muting VOX muting is standard on the AMIS250 A mic or line signal on channels 1 or 2 will mute channels 3 4 5 and 6 The muting function can be disabled via an internal link Phantom Power Phantom Power 18V DC is available from all mic inputs A rear panel phantom power on off switch is also provided Protection Internal current limiting protects the amplifier from both overload and overdrive conditions Australian Monitor Installation Series amplifiers feature a protection network that provides greater stability and performance Our amplifiers are recognised worldwide for their reliability and this is due to the extensive levels of current limiting which protect the amplifiers from both overload and overdrive conditions IFIER MIS 2S eh SPECIFICATIONS Power Output 250 watts RMS Maximum Load 20 Ohms 70 Volts Power Bandwidth 60Hz 17kKHz 3dB Frequency Response 60Hz 23kHz 3dB Total Harmon
28. ection Box features a balanced XLR MONITOR output a 6 35 mm TRS through output 3 stage pad offering up to 40dB of attenuation amp a ground lift switch for hum elimination Buzz Off HE2 Dual Hum Eliminator tool for eliminating hum amp signal noise caused by ground loops The AMIS HE2 has two discreet signal paths via balanced XLR inputs amp outputs The AMIS HE2 is a passive device amp can also be used as a converter of balanced amp unbalanced signals As part of the AMIS Contractor Tools range the AMIS HE2 is an inexpensive Drop Me 70 volt to line level converter with phoenix to XLR and level control AMIS26 2 x 6 Mic Line Distribution Amplifier 24VDC Phantom Power switchable per input Either input can be routed to any of the 6 outputs via front panel dip switches MP8 8 Channel Monitor Panel 100 70V Line or Low Impedance Applications Includes 2 5 inch speaker with volume control Simply select any of 8 amplifier via the front panel switch and you can monitor its output through the speaker and via an LED array Signal Present LED provided for each zone for easy troubleshooting Loop in loop out terminal strips for inputs from amplifiers and outputs to speakers r O ka ie a mn jii e e pe s i a a m f O A F Sel et N E x i HETITIITIa ETECIECTITTTa EFTEFTTITrE
29. hitectural and Engineering Specifications The 250 watt power amplifier shall be designed to run 70 volt line audio systems The unit shall also features a four ohm output The amplifier may be desk or rack mounted The unit Shall feature high temperature protection with front panel indication A built in auto temperature sensing fan shall cool the unit when required and automatically turn off again once the amplifier is running at the correct temperature The amplifier must be capable of delivering 250 watts into a 20 ohm inductive load with less than 0 5 distortion measured at 1kHz and with system hum and noise less than 74dB The amplifier Shall be an Australian Monitor Installation Series model AMIS250P AUSTRALIAN HO NITOR ABOUT Australian Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20 years experience in the design and manufacture of audio amplifiers and associated products They are a dynamic corporation priding themselves on excellent customer service better features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide AUSTRALIAN MONITOR 2 chan 120 Watt 70 Volt 8 Ohm AMP di Australan Monty Description The AMIS1202P is a dual channel 120W 120W power amplifier designed to deliver continuous full range performance in a compact and reliable package The AMIS1202P is two independent amplifiers in the one chassis
30. ic Distortion 0 5 1kHz rated power Signal To Noise Ratio 74dB with all controls at center Tone Controls Bass 100Hz Boost 12dB Cut 12dB Mid 600HZz Boost 12dB Cut 12dB Treble 10kHz Boost 9dB Cut 9dB Inputs Six mic aux universal inputs with XLR female mic sockets and dual RCA Phono aux sockets 600 ohm transformer balanced telephone paging input Input Sensitivity Mics 1mV 200 Ohms Aux 150mV 47K Ohms Outputs Speaker 70 V 4 Ohms Tape 350mV 10K Ohms Line Balanced 700mV Phantom Power 18 Volts DC on all Mic inputs Controls 6 Input channel gain controls 1 Bass control 1 Mid Control 1 Treble control 1 Master gain control 1 Phantom Power on off switch Tone Generators Four tone generator with Bell Pre Announce Alert and Evac Muting Built in VOX muting Channels 1 and 2 will mute channels 3 4 5 and 6 Indicators Power on and Protect LED Power Source 120VAC 60Hz 3 pin IEC 24VDC Power Consumption 400 Watts Dimensions 30 HX 19 Wx 13 D Weight 33 1lb AUSTRALIAN MONITOR ABOUT Australian Monitor Corporate Headquarters gt is located in Sydney FFEITFIITIEIIIE te Australia The organization has more he a than 20 years experience _ ett By A ale in the design and manufacture of audio amplifiers and associated products They are a dynamic corporation priding themselves on excellent customer service better features and lower priced products for Sound Contracto
31. ion The DigiPage Microphone Station comes in 8 zone or 16 zone versions They are easy to use and combined with the DigiPage Wall Panel are often all a client needs to use in their day to day operations Both the microphone stations are easily connected in a daisy chain format via CAT 5 Base 7 x 4 5 DigiPage Wall Panel The DigiPage Wall Panel allows users to select up to Six program inputs and adjust volume in their zone They are easy to use when combined with the wall panels and are easily connected in a daisy chain format via CAT 5 3 x 4 5 x 1 4 edt eer Als Tee i EE a T Pins ee y FL ij may F MME nem FG a i a a ate ke FI a WE rt a Pa pe Teua Pe ma PE 7 ns as SABC pe r i Bx Fi Bi Er TE 7 BE a EAT m 5 iici cok z E LOTA ti pa ia EFIE i J5 1 hi T e TE it a ee a ee at l som a L a le Lod kE FD 1 a _ L Ee nam La jil coe man 5 ie CAS Au J I Thh ee oe 1 PS la SiCG Ht L L tiac iaca iee l J bieri hed ee Y E T PEN i ae os 7 x nm iE 1 4 E DE H N ras Lo J i PH G e oh a A Pi PROG LALN IFE BEH pH ae l woe DOH Fi poaa TE o pas PH Pe salam 4 J Ba A ee BE D Lis y EAA iH Me J ee Bren Si CORA EFH rirani ram Er TH EFF FH eer i J ey Coe E Dirai m Ce II lt E TF ALTE TaN Fk H beri Leva mela LiL ko aas 7 Td mene O a EET AUSTRALIAN MONITOR ABOUT Australi
32. is a one rack unit fourth order Linkwitz Riley electronic crossover The AMIS23X can be confi gured as either a stereo two way or a mono three way crossover Featuring clip LED indication per band per channel frequency range selector switch CD horn boost switch amp polarity reverse switching the AMIS 23X is a professional price performing crossover Compressor Limiter m aie u l ee a a co a ae C ee a E a a a ee ee E E S E Ea Ea ESTS EES Bios Ea Li a ee ES ba FEE a H i A r j t P F a i i a 1 p o a i i i a Ei a peppen ee ee ee E a Bili j m ar TEA Tepp Me p oo ema z The Australian Monitor Pro Series AMIS CL2 is a 1 RU dual channel compressor limiter Featuring an expander gate compression amp limiting per channel the AMISCL2 utilizes a high quality VCA to give excellent performance from a budget priced dynamics processor With added features like selectable Automatic attack amp release times amp EQ enhancement which automatically compensates for high end loss when heavy compression is taking place the AMISCL2 has the features amp the performance of a compressor limiter many times the price AMIS 23x amp CL2 SPECIFICATIONS Frequency Range X1 80Hz to 920 Hz X2 800Hz to 9 2 kHz Hum and Noise gt 93dBu Low Frequency Section Output OdB lt 106 dBu High Frequency Section Output 0 dB lt 97d dBu Signal To Noise Ratio 118 dB CONTRO
33. itivity 0 5 Volt RMS 70 Volt Input Impedance 10K Ohms Input Connection Active balanced input with male and female 3 pin XLR input output Outputs 70 Volt line and 4 8 Ohm via rear panel barrier strip Line out to feed additional amplifiers from one of the paralleled XLR input Controls Front power switch Recessed rear input attenuator per chan Metering Indicators Signal present LED per chan Power Source 120VAC 60Hz 3 pin IEC 24VDC Power Consumption 400 Watts maximum Protection Fuses for overload amp Short circuit protect High temperature trip at 120 C DC Output Sensing disconnects load if DC is present Dimensions 3 5 H x 19 Wx 11 D Weight 3 1lb Rack Mounting Standard AMIS 1202P AUSTRALIAN MoO NITOR Architectural and Engineering Specifications The power amplifier shall be a dual channel model capable of delivering 120 watts RMS per channel into 70 volt line or 4 8 ohm loads The unit shall feature a signal present LED per channel Speaker connection shall be via a rear panel barrier Strip The amplifier shall have two balanced XLR inputs per channel one of which can be used to feed additional power amplifiers The unit shall also include fuse protection for overload and short circuit conditions The unit shall also feature generous heatsinking for reliable operation in extreme conditions The unit shall be of high quality suitable for continuous reliable performance It shall have a fre
34. making it the perfect choice for multi zone or multi channel applications Inputs and Outputs The AMIS1202P provides dual balanced XLR inputs male and female per channel These two inputs are wired in parallel enabling a line level split to be taken from the second input of each channel 70 volt line and 4 8 ohm outputs are available via the rear panel barrier strip Controls and Metering A recessed input attenuation control for each channel is included on the rear panel These pots are accessible using a screwdriver The AMIS1202P features a signal present LED per channel and power on LED Protection The AMIS1202P features slow start and dual AC and DC fuse protection Also featured is automatic speaker protection The AMIS1202P includes generous heat sinking for reliable operation in even the most extreme conditions Australian Monitor Installation Series amplifiers feature a protection network that provides greater stability and performance Our amplifiers are recognized worldwide for their reliability and this is due to the extensive levels of current limiting which protect the amplifiers from both overload and overdrive conditions AMIS 1202P SPECIFICATIONS Power Output 120 Watts per channel Maximum Load 40 Ohms on 70 Volt line setting Frequency Response 60Hz 23kKHz 3dB Total Harmonic Distortion 0 5 at 1kHz 1 Watt full power Signal To Noise Ratio 80dB at 70V 80dB at 8 Ohms 80dB at 4 Ohms Input Sens
35. me and thus can be set up to give a limited volume range to the end user e Supplied with RC1 remote volume control as a complete kit ready for installation AMTONE 1 Tone Module e Generates four tones Evacuation Alert Bell and Pre Announce Chime MX 61 SPECIFICATIONS FREQUENCY RESPONSE 20Hz 20kKHz 0 3dB TOTAL HARMONIC DISTORTION gt 0 1 1kHz SIGNAL TO NOISE RATIO gt 90dB all pots at center CROSSTALK gt 70dB TONE CONTROLS BASS 100HZ 12dB MID 1 6KHZ 12dB TREBLE 10KHZ 12dB SENSITIVITY Mic Sens 4 36mV 45dBu Imp 1k 3 Ohm Trim center OdB Line Sens 0 775V OdBu Imp gt 100k RCA 200mV 12dBu Imp 30k Ohm MAX LEVEL IN XLR mic 15dBu line 30dBu RCA gt 30dBu MAX LEVEL OUT 21dBu PHANTOM POWER 15V DC MASTER OUT Nominal Level OdBu into 1k Ohm Imp 100 Ohm MONO HEADPHONE OUT Nom 6dB into 200 Ohm Imp 10 Ohm MONO REC OUT Nom 12dB into 10k Ohm Imp 10k Ohm POWER INPUT AC 115V 60HZz 3 pin IEC DC 24 Volts POWER CONSUMPTION MAX TVA FUSES MAINS 115V 120mA DIMENSIONS HxWxD 1 75 x19 x7 2 WEIGHT NET 6 1lb SHIPPING 8 3lb MX6 1 Architectural and Engineering Specifications The Mixer shall be standard 1 rack unit in height and shall operate via mains power or via 24 volt DC supply The unit shall feature 6 XLR inputs switchable between standard mic line level and dual RCA line level inputs Each channel input shall have signal present LED indication and 15dB gain trim
36. nator may be required An electronically balanced 600 ohm telephone input for paging is also provided Outputs The AMIS120XL features 70 volt 4 amp 8 ohm isolated transformer outputs plus a tape recorder output by means of dual RCA sockets A balanced 700mV XLR output is also provided to feed up to 6 power amplifiers A vox triggered relay output is also available on the rear panel for activation of external devices from the vox muting circuit In most cases this would be used as a muting bypass relay which when used with the appropriate external attenuator will maintain paging levels irrespective of the attenuator setting VCA Control The master volume level can be controlled remotely External VCA control would normally be via a pot connected to a two wire rear panel barrier strip Tone Generator The AMIS120XL comes standard with an in built four tone generator module Tones include Bell Pre announce Chime Alert Tone and Evacuate Tone Any of these tones may be activated from a simple contact closure connected to the rear panel of the amplifier Muting Multiple levels of VOX muting is standard on the AMIS120XL A mic or line signal on channels 1 will mute channels 2 to 8 on channel 2 will mute 3 8 and channel 3 will mute 4 8 The muting function can be disabled via an internal link A vox triggered relay output is also available on the rear panel for activation of external devices from the vox muting circuit In most cases this wo
37. nically balanced 600 ohm telephone input for paging is also provided An insert point is also featured on the rear panel for those applications where an additional EQ or feedback eliminator may be required Outputs The AMIS120 features 70 volt 4 amp 8 ohm isolated transformer outputs plus a tape recorder output by means of dual RCA sockets A balanced 700mV XLR output is also provided to feed up to six power amplifiers A vox triggered relay output is also available on the rear panel for activation of external devices from the vox muting circuit In most cases this would be used as a muting bypass relay which when used with the appropriate external attenuator will maintain paging levels irrespective of the attenuator setting VCA Control The master volume can be controlled remotely External VCA control would normally be via a pot connected to a two wire rear panel barrier Strip Speaker Zone Selector A six position push button speaker zone selector with overriding all cal is located on the front panel Each of the six zone selectors switch the 70 volt speaker line output to six separate speaker zones The all call selector overrides all 6 zones regardless of their on off condition and places the 70 volt output to all six zones Tone Generator The AMIS120 comes standard with an in built four tone generator module Tones include Bell Pre Announce Chime Alert Tone and Evacuate Tone Any of these tones may be activated from a sim
38. ning or Y split cables The unit shall also include fuse protection for overload and short circuit conditions The unit shall also feature generous heatsinking for reliable operation in extreme conditions The unit shall be of high quality suitable for continuous reliable performance It shall have a frequency response of no less than 80Hz 20kHZz 3dB Distortion shall not exceed 1 at 1kHZ The signal to noise ratio shall be 94dB on 100V setting or better The power amplifier shall be packaged in a rugged 2 rack unit metal chassis suitable for desk or rack mounting The amplifier shall be an Australian Monitor Installation Series model AMIS 480P AUSTRALIAN HONI TOR ABOUT Australian Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20 years experience in the design and manufacture of audio amplifiers and associated products They are a dynamic corporation priding themselves on excellent customer service better features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide AVL TR Ls MONITOR Zone Paging System Starts as an 8 x 8 system and can be expanded to a 16 x 16 From 8 to 16 zones Remote paging stations Remote source amp volume selection Extremely user friendly remote panels Extremely contractor friendly CAT 5 cable DigiPage Base Station Each of the 8 zones has a dedicated local mic line in
39. nputs The AMIS60 has four universal input channels with separate level controls Each channel will accept balanced or unbalanced microphone line and auxiliary inputs The unit has industry standard XLR microphone sockets and dual RCA auxiliary sockets for each channel An electronically balanced 600 ohm telephone input for paging is also provided An insert point is also featured on the rear panel for those applications where an additional EQ or feedback eliminator may be required Outputs The AMIS60 features 70 volt and 8 ohm isolated transformer outputs plus a tape recorder output by means of dual RCA sockets A balanced 7OOmvV XLR output is also provided to feed up to 6 power amplifiers A vox triggered relay output is also available on the rear panel for activation of external devices from the vox muting circuit In most cases this would be used as a muting bypass relay which when used with the appropriate external attenuator will maintain paging levels irrespective of the attenuator setting VCA Control The master volume can be controlled remotely External VCA control would normally be via a pot connected to a two wire rear panel barrier Strip Speaker Zone Selector A six position push button speaker zone selector with overriding all cal is located on the front panel Each of the six zone selectors switch the 70 volt speaker line output to 6 separate speaker zones The all cal selector overrides all 6 zones regardless of
40. ockets The AMIS120P features 70 volt 8 and 4 ohm isolated transformer outputs via a rear panel barrier strip Protection Internal current limiting protects the amplifier from both overload and overdrive conditions Should the amplifier be overdriven a current limiter will protect the unit and in a worst case scenario the amplifier will shut down until the problem is resolved Once the problem is fixed shorted speaker line or overdriven input the amplifier will automatically reset and continue operation The AMIS120P features generous heatsinking Australian Monitor Installation Series amplifiers feature a protection network that provides greater stability and performance Our amplifiers are recognized worldwide for their reliability and this is due to the extensive levels of current limiting which protect the amplifiers from both overload and overdrive conditions AMIS 120P SPECIFICATIONS Power Output 120 Watts RMS Maximum Load 40 Ohms 70 Volts Power Bandwidth 60Hz 17kHz 3dB Frequency Response 60Hz 23kHz 3dB Total Harmonic Distortion 0 5 1kHz rated power Signal To Noise Ratio 80dB Input Sensitivity 700mV Outputs 70V 4 Ohm 8 Ohm Controls One gain control on rear of the unit via flathead screwdriver control Indicators Power on LED Power Source 120VAC 60Hz 3 pin IEC connector 24VDC Power Consumption 300 Watts Protection Current Limiter protection plus AC and DC fuses Dimensions 3 5 H x 1
41. or 110V 60Hz special order 3 pin IEC connector Power Consumption 7 Watts Dimensions 1 73 X19 X7 2 Weight 8 81 lbs TX8202 AUSTRALIAN HO NITOR ARCHITECTURAL AND ENGINEERING SPECIFICATIONS The mixer shall have 4 balanced mic line inputs and 4 stereo line inputs The mic line channels shall be balanced and feature 3 pin female XLR sockets The stereo line channels shall have dual female RCA sockets Each channel shall include tamper resistant treble bass and pan controls The first four channels feature a line level direct output which can be used to feed additional amplifiers mixers or recording devices An internal jumper shall allow the first four inputs to be removed from the master left right outputs while still retaining their direct output function The equalization per channel shall provide 12dB cut or boost at 100Hz and 10dB cut or boost at 10kHz The master section shall include individual level controls for both the Left and Right outputs and shall also include two 7 segment output level LED meters The master outputs shall be balanced 3 pin XLR male sockets and dual RCA female sockets for the stereo tape output A 1 4 stereo headphone socket shall be included for monitoring The mixer shall include on board muting card as well as a option for 4 tone generator modules and remote master VCA control The mixer shall be of high quality suitable for both live and commercial applications It should have ample
42. otely One stereo source can have selectable priority per zone and each stereo zone boasts 5 stage equalization The ZoneMix3 also has the ability to route two independent mic or line signals to any zone or combination of zones Add to this remote volume controls in each zone and the ZM3M 3 zone paging microphone both running via inexpensive CAT 5 cabling and you have an extremely high quality zone selecting mixer at a fraction of the cost of other products in this market Inputs There are two MIC LINE inputs The balanced XLR inputs accepts mic level signals The dual RCA inputs accept line level inputs and are summed to mono internally Gain and EQ are controlled from the front panel These inputs supply 15V phantom power unless internally disabled These inputs may have priority over program inputs if this feature is enabled There are four program inputs These are stereo RCA line level inputs Trim is controlled from the front panel LINE4 is a priority input if this feature is enabled PAGE INPUT There is an RJ45 connector on the rear of the unit accepts a CAT 5 cable from the optional ZM3M Paging Station SUM INPUT This input has overall priority and is usually used for an emergency tone or message Outputs There are 3 Stereo Zone balanced XLR Outputs The zone outputs are configured as stereo left and right as default but can be internally changed to mono Link Two ZoneMix3 Units can be linked together to provide six
43. ple contact closure connected to the rear panel of the amplifier A Pre announce defeat switch is located on the front panel Muting VOX muting is standard on the AMIS120 A mic or line signal on channels 1 or 2 will mute channels 3 and 4 The muting function can be disabled via an internal link AMIS 120 SPECIFICATIONS Power Output 120 Watts RMS Maximum Load 40 Ohms 70 Volts Power Bandwidth 60Hz 17kHz 3dB Frequency Response 60Hz 23kHz 3dB Total Harmonic Distortion 0 5 1kHz rated power Signal To Noise Ratio 74dB all controls center Tone Controls Bass 100Hz Boost 12dB Cut 12dB Treble 10kHz Boost 9dB Cut 9dB Input Sensitivity Mics 1mV 200 Ohms Aux 150mV 47K Ohms Outputs Speaker 70 Volts 4 amp 8 Ohm Tape 350mV 10KOhms Line Balanced 700mV Phantom Power 18V DC on Mic ins Switch Controls 4 input channel gain 1 Bass control 1 Treble control 1 Master gain control 6 Speaker zone selector 1 Speaker all call selector 1 Pre announce defeat switch 1 Phantom Power switch Tone Generators Four tone generator with Bell Pre Announce Alert and Evac Protection Soft limiter for overload protection plus AC and DC fuses Muting Channels 1 and 2 will mute channels 3 and 4 Indicators Power on LED Power Source 120VAC 60Hz 3 pin IEC connector 24VDC Power Consumption 250 Watts Dimensions 3 5 H x 19 W x 13 D Weight26 5lb AMIS 120 AUSTRALIAN MONITO
44. plus AC and DC fuses Muting Channels 1 and 2 will mute channels 3 and 4 Indicators Power on LED Power Source 120VAC 60Hz 3 pin IEC connector 24VDC Power Consumption 125 Watts Dimensions 300 A amp 19 WX 13 D Weight 22 Ibs AUSTRALIAN MONITOR Phantom Power ABOUT Phantom Power 18V DC is available from all mic inputs A rear panel Australian Monitor phantom power on off switch is also provided Corporate Headquarters is located in Sydney Australia The organization has more n ie than 20 years experience in the design and manufacture of audio ETEELEIITIIGTGE Rack Mounting amplifiers and Standard associated products Protection l Internal current limiting protects the amplifier from both overload and They are a dynamic overdrive conditions Australian Monitor Installation Series amplifiers corporation priding feature a protection network that provides greater stability and themselves on excellent performance Our amplifiers are recognised worldwide for their reliability customer service better and this is due to the extensive levels of current limiting which protect the amplifiers from both overload and overdrive conditions features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide dhli Brel Bhi Hi m rim i ce yy LEF E FE ey FE EH Se BEL A EH qapey aod 6 ol fa m T EE erT ma ia Let g LL as oer SH E ma
45. poration priding themselves on excellent customer service better features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide AUSTRALIAN MONITOR 2 Channel 15 Band Equalizer The Australian Monitor Pro Series AMIS 215EQ is a single rack unit graphic equalizer Featuring constant Q circuitry selectable 6dB or 12dB slider range balanced XLR 6 35mm TRS amp unbalanced RCA inputs amp outputs EQ bypass switches ground lift switches output level controls amp overload LED s The Australian Monitor Pro Series AMIS 31EQ is single rack unit graphic equalizer Featuring constant Q circuitry selectable 6dB or 12dB slider range balanced XLR 6 35mm TRS amp unbalanced RCA inputs amp outputs EQ bypass switches ground lift switches output level controls overload LED s amp variable high amp low pass filters The features found in Australian Monitor Pro Series graphic EQ s are usually associated with equalizers many times the price of these The AMIS 215EQ and AMIS 31EQis an extremely well featured graphic equalizer at a contractor friendly price AMIS 215 EQ amp 31EQ Single Channel 31 Band Equalizer EQUALIZER AMIS215EQ 2 x 15 2 3 Octave ISO Spacing from 20Hz 20kHz AMIS31EQ 31 1 3 Octave ISO Spacing from 20Hz 20kHz Type Constant Q Accuracy 3 Center Frequency Travel 20mm Positive Centre Detent Range 6dB or 12dB selectable 2 INPUTS Type
46. pping 0 5 Inputs 3x Mic Aux Input connectors 3x XLR RCA Mic sensitivity 1mV 0 2mV AUX sensitivity 0 5V 100mV S N ratio gt 75dBr Bandwidth On 70V terminals 75Hz 15kKHz 3dB 0dB Tone Controls Bass 100Hz 12 dB Treble 10kHz 9 dB Power source Switchable 115V 60 Hz 230 240V 50Hz Current draw full power 1 38A Fuses 1A AC mains amp DC Line Out 1V Tape Out 300mV Mic 1 Automatic Priority over Mic2 3 Size 19 W x 3 5 H x 11 1 D Protections 1 Short circuit 2 Thermal at 95 Output Regulation 96 Net Weight 18 7lb 1 Shipping Dimensions 20 1 W x 5 7 H x 11 7 D Shipping Weight 23 1 Ib Warranty 1 year AMC 60 ABOUT Australian Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20 years experience in the design and manufacture of audio AUSTRALIAN MO NITOR 70 Voltage cable run distances to cable type amplifiers and 50m AWG24 associated products 50m 200m AWG18 They are a dynamic Over 200m AWG16 corporation priding 4 Ohm cable run distances to cable type themselves on excellent 10m AWG18 customer service better 10m 30m AWG13 features and lower priced Over 30m Not recommnded products for Sound Contractors and Audio Visual Integrators worldwide Rae CPL LEP ES ii ae LL Fi Lae cn ee Se rey pip Taber DUSIN etri Brut 3 Lie Sera Bie ZETA G T ep an ee l BOO mm FS
47. put 6 Mic Line inputs routable to any of the 8 zones or 16 when a slave unit is added 1 priority input which has total priority over all other inputs and is activated by contact closure The priority input has its own level control Alert Evacuation Bell and Pre Announce Chimes Priority Ducking Circuitry 4 CAT 5 ports which are used to connect to the remote zone paging microphones and the remote source volume selectors which are daisy chained on CAT 5 cable Various levels of input and output level control Multi stage volume status LEDs amp easy input selection Separate paging volume level adjustment per zone Treble and Bass control per zone SPECIFICATIONS Data Digital Audio Mic RJ45 CAT5 Connector Program Sources Trim Max Unbalanced RCA Input Impedance 100KQ Sensitivity 150mV Balanced XLR Input Impedance 1k3Q Sensitivity 1mV Min Trim 46dB Local Source Unbalanced RCA Input Impedance 100KQ Sensitivity 1 5V Balanced XLR MIC Input Impedance 1k3Q Sensitivity 11mV Balanced XLR LINE Input Impedance 45KQ Sensitivity 350mV Sum Input Input Sensitivity 330mV Threshold 46dBu at output ind of input Frequency Response 3dB 15Hz 17kHz THD 0 005 Noise Page Mic 84dB Other Inputs 89dB Power Supply 2 4VDC 30VA Plug pack Dimensions H x W x D 5 2 x 19 01 x 6 7 Weight 13 2 Ibs Shipping weight 15 4 Ibs BC ANC DigiPage Microphone Stat
48. puts from both CD players as well as a stereo priority output The BGM2 series provides a high quality rack space friendly and extremely well featured dual background music source at a contractor friendly price BGMe2 DCD AUSTRALIAN HO NITOR ABOUT Australian Monitor ga ece Corporate Headquarters coos zal is located in Sydney Australia The organization has more than 20 years experience in the design and Architectural and Engineering Specifications manufacture of audio The background music source shall be a standard 1RU 19 rack size amplifiers and and comprise dual MP3 compatible CD players Each program source will associated products have a dedicated stereo output as well as a stereo priority output where They are a dynamic source two will have priority over source one corporation priding The CD player shall be programmable up to 20 tracks and shall have themselves on excellent infrared control available customer service better The unit shall be an Australian Monitor BGM2DCD features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide BGM TCD CD player and Tuner AUSTRALIAN MONITOR SPECIFICATIONS CD MP3 PLAYER fee a a mS NLO Output Level JEE 1kHz 0dB 1 2V 0 3V Frequency Response BGM2 TCD O 20Hz 20kHz 2dB Separation 1kHz OdB gt 60 dB 1 RU dual program source T H D Noise MP3 compatible CD player 1kHz 0dB lt 0 05 Option
49. quency response of no less than 60HZz 23kHz 3dB Distortion shall not exceed 0 5 at 1kHz The signal to noise ratio shall be 80dB on 100V setting or better The power amplifier shall be packaged in a rugged 2 rack unit metal chassis suitable for desk or rack mounting The amplifier shall be an Australian Monitor Installation Series model AMIS1202P ABOUT Australian Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20 years experience in the design and manufacture of audio amplifiers and associated products They are a dynamic corporation priding themselves on excellent customer service better features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide AVL Te Ls MONITOR 4 Chan 80 Watt 70 Volt 8 Ohm AMP AMIS 480P THERMAL POWER fx Australian Monitor INSTALLATION SERIE Ss The Australian Monitor Installation Series AMIS480P is a robust highly featured 4 channel power amplifier Offering 4 independent channels each delivering 80 watts into 4 ohms or 70 100 volt line the AMIS480P is designed to operate in extreme conditions to give the contractor the most reliable 4 channel amplifier available today Engineered with maximum attention to channel isolation with individual ground lift switches and level control for each channel the AMIS480P will operate as 4 individual amplifiers in a rack space friendly 2RU cha
50. r of professional balanced XLR signals to a consumer level stereo RCA signal The stereo path has its own volume control The AMIS SC2 is powered by a supplied 12 VDC power supply Get Down 2 Way Stereo Converter converts professional level to consumer level signals Let s Split MSC1 Microphone Splitter Combiner produces 2 balanced XLR signals 1 direct 1 transformer isolated from a single balanced XLR input The AMIS MCS1 provides a ground lift switch to eliminate hum Let s Split LSC1 Line Splitter Combiner produces 2 balanced XLR signals 1 direct 1 transformer isolated from a single balanced XLR line level input The AMIS LSC1 provides a ground lift switch to eliminate hum Mixed Up PM4 4 Channel Passive Mixer is a 4 input 1 output passive mixer that can be used for mixing 4 mics instruments or line sources or forconverting stereo feeds to mono The AMIS PM4 requires no batteries or other external power source The unit features unbalanced 6 35mm jack inputs amp outputs and can be used as a 1 in 4 out signal splitter when all channel volumes are run at maximum Gh EC Ll MONITOR ue eee 3 ay CONTRACTOR TOOLS AUSTRALIAN Pre Me PRE1 Mini Microphone Preamp features balanced XLR amp unbalanced 6 35mm jack inputs amp outputs switchable 36 volt phantom power gain control amp signal clip LED Powered by a supplied 12VDC power supply Injector DI1 Passive Direct Inj
51. reble and bass controls and feature a balanced XLR line level output as well as a dual RCA record level output There shall also be facility for the mixer to accept a tone generation module The mixer shall be an Australian Monitor AMC MIX AUSTRALIAN MO NITOR ABOUT Australian Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20 years experience in the design and manufacture of audio amplifiers and associated products They are a dynamic corporation priding themselves on excellent customer service better features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide AVL TR Ls MONITOR 6 Channel 1RU MIXER a I a a i M gt M E eee i a 11 1 re pm m 1 _ ei bom it be 2 li i Ai pe Ca D uE z i ba r m r ri i 1 I 1 Pa F 1 a a a ig i fy Pr a L b a ae oom is i r T anaa d ai o vax 6 input mono mixer XLR input switchable between mic amp line level 15dB gain trim control per input Input 1 is switchable to be pre post master 24VDC or mains power operation Optional remote VCA Tone generator Muting boards Whisper quiet operation Dual color signal present indication LED per input The Australian Monitor Installation Series MX61 mixer brings a range of new features to the AMIS standard 1 RU mixer range The MX61 mixer featu
52. res the new Australian Monitor Standard AMS input section which has an XLR input switchable between mic amp line level dual RCA line inputs signal present LED indication individually switchable phantom power amp 15dB of gain trim available per input The MX61 also boasts whisper quiet operation 4 segment output level indication amp balanced line output record output amp headphone outputs The MX61 has 6 AMS inputs to one output amp will operate via 110 or 220 240 VAC or 24VDC via an external 24 volt power supply Optional remote VCA volume control tone generators amp muting boards are also available for the MX61 The MX61 mixer is extremely versatile amp represents excellent value for money OPTIONS not included AMMUTE 1 Single Stage Priority Mute Module e Allows for muting of channels 2 and higher when signal is present at channel 1 and the channel volume is turned up AMMUTES Triple Stage Priority Mute Module e Allows for muting of channels 2 and higher when signal is present at channel 1 e Allows for muting of channels 3 and higher when signal is present at channel 2 e Allows for muting of channels 4 and higher when signal is present at channel 3 e Ability to adjust threshold of the trigger signal along with the the release time of the ducked signal AMVCA Remote Master Volume Control e Enables the end user to utilize a localized volume control e Remote volume control is pre the mixers front panel master volu
53. rive additional power amplifiers shall also be provided This unit shall offer remote master VCA control 24V DC and mains power operation and a vox triggered relay output The amplifier master section shall include one master gain control two EQ controls one with 12dB of cut and boost at 100Hz and the other with 9dB of cut and boost and 10kHz speaker outputs shall be transformer isolated at 100V 70V 4 amp 8 ohms The amplifier must be capable of delivering 120 watts RMS into an 80 inductive ohm load with less than 0 5 distortion measured at 1kKHz and with system hum and noise less than 74dqB The amplifier shall be an Australian Monitor Installation Series model AMIS120 BLE Ts Ls MONITOR 8 Input 120 Watt MIXER AMPLIFIER i Asiak Monitor Description The AMIS120XL is an 8 channel 120 watt mixer amplifier suitable for rack or desk mounting The amplifier is a self contained compact unit of solid steel construction This amplifier features a status LED Inputs The AMIS120XL has eight universal input channels with separate level controls Each channel will accept balanced or unbalanced microphone line and auxiliary inputs The unit has industry standard XLR microphone sockets and dual RCA auxiliary sockets for each channel Rear panel dip switches per channel allow the adjustment of line input sensitivity An insert point is also featured on the rear panel for those applications where an additional EQ or Feedback Extermi
54. rovided for the addition of signal processing A vox triggered relay output for external devices shall also be included The amplifier master section shall include one master gain control three EQ controls one at 100Hz with 12dB of cut and boost one at 600Hz with 12dB cut and boost and the other with 9dB of cut and boost at 10kHz Speaker outputs shall be transformer isolated at 70 volt 4 amp 8 ohms The amplifier must be capable of delivering 120 watts RMS into a 40 inductive ohm load with less than 0 5 distortion measured at 1kHz and with system hum and noise equal to or better than 74dB Power consumption shall be 120 watts at max power The amplifier shall be an Australian Monitor Installation Series model AMIS120XL BLE Ts Ls MONITOR 6 Chan 250 Watt MIXER AMPL ee EI Tr EF Erre i i i Fis sra Fioni IPL ee E Description The AMIS250 is a 6 channel 250 watt mixer amplifier suitable for rack or desk mounting The amplifier is a self contained compact unit of solid steel construction Inputs The AMIS250 has six universal input channels with separate level controls Each channel will accept balanced or unbalanced microphone line and auxiliary inputs The unit has industry standard XLR microphone sockets and dual RCA auxiliary sockets for each channel An electronically balanced 600 ohm telephone input for paging is also provided An insert point is also featured on the rear panel for those applications where an ad
55. rs and Audio Visual Integrators worldwide mhis Fis ee menj AF LEFF E FH ee E i Zr TEF SAE AAI g E a c E EL T ERE a ts cro gE gt LPI LL G hi Architectural and Engineering Specifications The mixer amplifier shall have six universal inputs each comprising of a balanced microphone with XLR female sockets and an auxiliary input using dual RCA sockets A balanced XLR output to drive additional power amplifiers shall also be provided The amplifier master section shall include one master gain control three EQ controls one with 12dB of cut and boost at 100Hz one with 12dB cut and boost at 600Hz and the other with 9dB of cut and boost at 10kHz Speaker outputs shall be transformer isolated at 70 volt and 4 ohms The amplifier must be capable of delivering 250 watts RMS into a 20 inductive ohm load with less than 0 5 distortion measured at 1kHz and with system hum and noise less than 74dB The amplifier shall AMIS250XL BLE Te Ls MONITOR 3 Chan MIXER fb Australian Monitor Yan INSTALLATION SERIES AMIC MIX 3 Mic line input mono mixer Master Volume overall treble amp bass controls 1 RU Optional tone generator On board priority The Australian Monitor Installation Series AMC MIX mixer brings the affordability amp ease of use of the AMC series amplifiers and offers accommodations a low cost mixer for applications where reliability is everything but the more elabora
56. s A Remote Volume Source Panel ZM3R is available per Australia The zone It is connected to the unit by CAT 5 cable From this organization has more panel the user may adjust volume and select one of the than 20 years experience four program sources or the OFF position in the design and manufacture of audio A Remote Paging Station ZM3M is available front photo amplifiers and It is connected to the unit by CAT 5 cable From this paging station a user may page into any or all of the 3 zones associated products They are a dynamic corporation priding themselves on excellent customer service better l features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide ARCHITECTURAL AND ENGINEERING SPECIFICATIONS The 1RU zone mixer shall be of a high specification suitable for foreground and background music applications The unit shall have a frequency response of 20Hz 20kHz OdB 3dB and signal to noise of 80dB or greater The zone mixer shall feature three stereo zone outputs with 5 stage EQ two mic line inputs and four stereo line inputs The inputs may be routed to any of the outputs Program source selection may be made via the front panel ora remote wall panel connected by CAT 5 cable The unit shall have an optional microphone paging station which allows the paging of the 3 individual zones or all zones at once The unit shall be an Australian Monitor ZoneMis3 ALIS TR Ls MO
57. ssis For ease of installation each channel input can be routed to the next channel via rear panel link switches eliminating the need for daisy chaining or Y split cables The AMIS480P also offers signal present and clip LED indicators for each channel as well as a thermal protect indicator The AMIS480P is a significant advance in 4 channel amp design offered at a contractor friendly price AMIS 480P SPECICIATIONS Power Output 4 x 80W Freq Response 1W 80Hz 20kHz DISTORTION 1 THD all channels driven Power Bandwidth 85Hz 20kHz S N Ratio 94dB ref 100V Crosstalk 1kHz 80dB 20Hz 20kHz Better than 60dB Input Sensitivity 0 775V RMS OdBu Input Impedance 20K Voltage Gain pot at max 100V out 129 42dB 70V out 90 39dB 4ohm out 23 27dB Output Regulation 95 1kHz Dimensions h x w x d 4 36 x 19 x 17 Weight 441b Shipping Weight 53lb AMIS 480P OUTPUT 2 OUTPUT 1 OHM LINE OHM LINE com 4 COM CE AC FU Architectural and Engineering Specifications The power amplifier shall be a four channel model capable of delivering 80 watts into 70 100 volt line or 4 ohm loads The unit shall feature a signal present LED and clip indicator per channel Speaker connection shall be via a rear panel barrier strip The amplifier shall have four balanced XLR inputs one per channel Each channel input can be routed to the next channel via rear panel link switches eliminating the need for daisy chai
58. te features of the MX mixers series are not required The AMC MIX is a 1 RU mixer that features 3 universal mic line inputs Master volume amp overall treble amp bass controls are provided along with vox triggered muting defeatable giving channel 1 priority over channels 2 amp 3 There is also facility to add an optional on board tone generator card The AMC MIX gives the contractor a low cost alternative in applications that are price sensitive but still require reliability amp a high level of sound reproduction I I AMC MIX SPECIFICATIONS FREQUENCY RESPONSE 20Hz 20kHz 0 3dB DISTORTION lt 0 5 1kHz THD SIGNAL TO NOISE RATIO gt 84dB pots at center CROSSTALK gt 60dB TONE CONTROLS BASS 100HZ 12dB TREBLE 10KHZ 9dB SENSITIVITY Mic Sens 0 7mV 61dBu Imp 1k30hm RCA 500mV 4dBu Imp gt 100kohm MAX LEVEL IN XLR mic 20dBu RCA gt 30dBu MAX LEVEL OUT 14dBu MASTER OUT Nominal Level OdBu into 1k Ohm Imp 100 Ohm MONO TAPE OUT Nom 16dB into 10k Ohm Imp 10k Ohm POWER INPUT 20V AC via 2 1mmx5 5mm barrel POWER CONSUMPTION 7 VA max DIMENSIONS HxWxD 1 75 x19 x7 54 WEIGHT Net 5 5lb Shipping 7 7 b AMC MIX Architectural and Engineering Specifications The mixer shall be 1RU in size with three universal XLR mic dual RCA line level inputs Channel 1 shall have priority over channels 2 amp 3 this can be defeatable if required The mixer shall have master volume t
59. te zones giving a volume range from off to whatever the master level on the AMIS ZRM4 relevant zone output is set to Alert Evacuation Bell amp Pre announce tones are also provided on board The AMIS ZRM4 is a compact yet extremely versatile zone routingmixer which makes the complex task of multizone signal routing simple amp cost effective SPECIFICATIONS Sensitivity input for OdBu out RCA In 26dBu to 4dBu 89mV to 1 23 V XLR Line In 26dBu to 4dBu 39mV 1 23V XLR Mic In 60dBu to 30dBu 0 78mV to 25mV Max Level In gt 14 1 Vrms 25dBu Max Level Out gt 15 4 Vrms 26dBu Frequency Response lt 5Hz to gt 22kHz OdB 3dB THD Less than 0 1 Noise lt 90dBu 20Hz 20kHz all pots centered Crosstalk lt 65dB 1kHz Phantom Power 15VDC Power Input 20VAC 600mA max or 24 to 34v DC regulated 600mA max Dimensions 44 0h x 482 0w x 188 0d Weight Net 6 4lb Shipping 9 7 b AUSTRALIAN MO NITOR ABOUT Australian Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20 years experience in the design and Architectural and Engineering Specifications manufacture of audio The zone routing mixer shall be 1 RU have 6 inputs with RCA amp mic line amplifiers and switchable balanced XLR s Each input will have individual 15 dB gain associated products control switchable 15VDC phantom power amp high pass filter Input 1 will They are a dynamic be a
60. their on off condition and places the 70 volt output to all 6 zones Tone Generator The AMIS60 comes standard with an in built four tone generator module Tones include Bell Pre announce Chime Alert Tone and Evacuate Tone Any of these tones may be activated from a simple contact closure connected to the rear panel of the amplifier A Pre announce defeat switch is located on the front panel Muting VOX muting is standard on the AMIS60 A mic or line signal on channels 1 or 2 will mute channels 3 and 4 The muting function can be disabled via an internal link SPECIFICATIONS Power Output 60 Watts RMS Maximum Load 80 Ohms 70 Volts Power Bandwidth 60Hz 17kKHz 3dB Frequency Response 60Hz 23kHz 3dB Total Harmonic Distortion 0 5 1kHz rated power Signal To Noise Ratio 74dB all controls center Tone Controls Bass 100Hz Boost 12dB Cut 12dB Treble 10kHz Boost 9dB Cut 9dB Input Sensitivity Mics 1mV 200 Ohms Aux 150mV 47K Ohms Outputs Speaker 70 Volts 4 amp 8 Ohm Tape 350mV 10KOhms Line Balanced 700mV Phantom Power 18 V DC Mic ins Switch Controls 4 input channel gain 1 Bass control 1 Treble control 1 Master gain control 6 Speaker zone selector 1 Speaker all call selector 1 Pre announce defeat switch 1 Phantom Power switch Tone Generators Four tone generator with Bell Pre Announce Alert and Evac Protection Soft limiter for overload protection
61. ting function can be disabled by moving an internal jumper Tone Generators Bell Pre Announce Chime Evacuate and Alert are included in the unit Each tone can be activated by a simple contact closure using the rear panel terminal block Phantom Power Phantom Power 15V DC is available on all mic inputs and can be disabled if required via a dip switch SPECIFICATIONS Frequency Response 50Hz 15kHz 3dB Total Harmonic Distortion Less than 0 1 1kHz Signal To Noise Ratio 74dBV all chans center Tone Controls Bass 100Hz Boost 12dB Cut 12dB Treble 10kHz Boost 10dB Cut 10dB Inputs 4 active balanced mic line inputs with 3 pin XLR female 200 600 Ohm Maximum Input Level is 500mV 4 Stereo Line inputs with dual female RCAs 47K Ohms Maximum Input Level is 1 5V Input Sensitivity Mic imV 200 Ohms Line 1 4 150mV 1V 47K Line 5 8 125mV 47K Phantom Power 15V DC on all mic channels switchable Outputs Left and Right Master 3 pin XLR male sockets 1 5V 600 Ohms Max Output Level 20dB Stereo Headphone Output 1 4 stereo socket 3 5V 600 Ohms Stereo Tape Output dual female RCA 400mV 10K Ohms Four direct line level outputs 600mV 10K Ohms Controls Level Control per channel Recessed Treble Bass and Pan Controls per channel Left and Right Master Level Indicators Power on orange LED 7 segment LED meters for both L and R outputs Power Source AC 240V 50Hz
62. trol e Enables the end user to utilize a localized volume control e Remote volume control is pre the mixers front panel master volume and thus can be set up to give a limited volume range to the end user e Supplied with RC1 remote volume control as a complete kit ready for installation AMTONE 1 Tone Module e Generates four tones Evacuation Alert Bell and Pre Announce Chime MX 81 SPECIFICATIONS FREQUENCY RESPONSE 20Hz 20kKHz 0 3dB DISTORTION gt 0 1 1kHz THD SIGNAL TO NOISE RATIO gt 90dB all pots at center CROSSTALK gt 70dB TONE CONTROLS BASS 100HZ 12dB TREBLE 10KHZ 12dB SENSITIVITY Mic Sens 4 36mV 45dBu Trim in center OdB Imp 1k30hm Line Sens 0 775V OdBu Imp gt 100k RCA 200mV 12dBu Imp 30k Ohm MAX LEVEL IN XLR mic 15dBu line 30dBu RCA gt 30dBu MAX LEVEL OUT 21dBu PHANTOM POWER 15V DC MASTER OUT Nominal Level OdBu into 1k Ohm Imp 100 Ohm MONO HEADPHONE OUT Nom 6dB into 200 Ohm Imp 10 Ohm MONO REC OUT Nom 12dB into 10kohm Imp 10k Ohm POWER INPUT AC 115V 60Hz 3 pin IEC320 C14 DC 24 Volts POWER CONSUMPTION 7 VA max FUSES MAINS 115V 120mA DIMENSIONS HxWxD 1 75 X19 x7 2 WEIGHT NET 6 1lb Architectural and Engineering Specifications The Mixer shall be standard 1 rack unit in height and shall operate via mains power or via 24 volt DC supply The unit shall feature 8 XLR inputs switchable between standard mic line level and dual RCA line level inputs
63. uld be used as a muting bypass relay which when used with the appropriate external attenuator will maintain paging levels irrespective of the attenuator setting AMIS 120XL SPECIFICATIONS Power Output 120 watts RMS Maximum Load 40 Ohms 70 Volts Power Bandwidth 60Hz 17kKHz 3dB Frequency Response 60Hz 23kHz 3dB Total Harmonic Distortion 0 5 1KHz rated power Signal To Noise Ratio 4dB with all controls at center Tone Controls Bass 100Hz Boost 12dB Cut 12dB Mid 600Hz Boost 12dB Cut 12dB Treble 10kHz Boost 9dB Cut 9dB Inputs Eight mic aux universal inputs with XLR female and dual RCA plugs 600 ohm transformer balanced telephone paging input Input Sensitivity Mics 1mV 200 Ohms Aux 150mV 47K Ohms with 9 12 15dB Pads Outputs Speaker 70 Volts 4 amp 8 Ohms Tape 350mV 10K Ohms Line Balanced 700mV Phantom Power 18V DC on all Mic ins Switch Controls 8 Input channel gain controls 1 Bass control 1 Mid Control 1 Treble control 1 Master gain control VCA rear panel strip Dip Switch per Channel for line sensitivity and phantom power and a vox relay ouput Tone Generators Four tone generator with Bell Pre Announce Alert and Evac Muting Channel 1 will mute chans 2 to 8 channel 2 mutes 3 8 channel 3 mutes 4 8 Also a vox relay toexternal devices Indicators Power on amp signal present LEDs Dimensions 3 5 H x 19 W x 13 D Weight 26 5lb AMIS 120XL
64. y 0 5V 100mV S N ratio gt 75dBr Bandwidth On 70V terminals 85Hz 15kHz 3dB 0dB Tone Controls Bass 100Hz 12 dB Treble 10kHz 9 dB Power source Switchable 115V 60 Hz 230 240V 50Hz Current draw full power 13A Fuses 1A AC mains amp DC Line Out 1V Tape Out 300mV Mic 1 Automatic Priority over Mic 2 3 Size 19 W x 3 5 H x 7 5 D Protections 1 Short circuit 2 No Thermal Output Regulation 96 Net Weight 13 21b Shipping Dimensions 20 1 W x 5 7 H x 11 7 D Shipping Weight 16 5lb Warranty 1 year RRE MONITOR 70 Voltage cable run distances to cable type 50m AWG26 50m 200m AWG20 Over 200m AWG18 4 Ohm cable run distances to cable type 10m AWG18 10m 30m AWG13 Over 30m Not recommnded om DOGODO RTPEE ae ae ba hice T iE 1i ae E Casou i a Ti jg EEE F L jm DE 1656 rove 0 72 a i AMC 30 ABOUT Australian Monitor Corporate Headquarters is located in Sydney Australia The organization has more than 20 years experience in the design and manufacture of audio amplifiers and associated products They are a dynamic corporation priding themselves on excellent customer service better features and lower priced products for Sound Contractors and Audio Visual Integrators worldwide elas Cel EHE EON EP i na Lae Fa ji ea a Fisha Habar LHI T omy On enteno LEELA pairi fo Lite Sutra

2007 All Spec Sheets

Contents

Download Pdf Manuals

Related Search

Related Contents