ATD-10538 3/8” Electric Drill
Contents
1. ATD 10538 3 8 Electric Drill Tool specifications Rated Voltage V Rated Frequency Hz Rated current A No load Speed RPM Speed Selection Right Left Rotation Chuck Size Drilling Capacity max Steel Wood Net Weight 120 60 3 3 0 2700 Yes Yes 3 8 10 mm 3 8 10 mm 3 4 20 mm 3 lbs 1 4kg WARNING To reduce the risk of injury please read this instruction manual before use Intended use The ATD10538 drill is intended for impact drilling in brick concrete as well as for drilling in wood metal ceramic and plastic Electrical safety The electric motor has been designed for 120V only Always check that the power supply corresponds to the voltage on the rating plate O Double insulation This tool is double insulated in accordance with EN60745 therefore no earth ground wire is reguired General safety rules for work with electric tools Read and understand all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury The term power tool in the warnings listed below refers to your electrically operated corded power tool or battery operated cordless power tool Safety warning and precautions Save this manual You will need the manual for the safety warning and precautions assembly instructions operating and maintenance procedures parts list and diagram Read these instructions before o2. PRT10538 04 SPINDLE 5 PRT10538 05 KEY 6 PRT10538 06 BALLBEARING 7 PRT10538 07 CIRCLIP Z Z NR ma 08 GEAR e 10 11 Lia 13 PE PRT10538 09 CIRCLIP 1 3 4 5 7 10 11 12 13 14 5 2 2
3. a Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tools is maintained Additional safety regulations WARNING Remove the plug from socket before carrying out any installation adjustment servicing or maintenance 1 Stay alert and use common sense when operating the tool Do not use the tool when tired or under influence of drug alcohol or medicine 2 Never put fingers on the switch button while moving the tool to avoid unintentional starting of the tool 3 Ensure the mounting screws and other assemblies are fixed properly and securely before operate the tool Turn on the switch and let the tool work for 30 second in a safe position Stop immediately if considerable vibration or other defects are detected have it repaired Description 1 Chuck 3 Ventilation slots 7 Forward Reverse switch 8 Speed selector thumbwheel 9 Switch 10 Lock button Applications Use only for the purposes listed below Drilling wood materials and resin boards Drilling metal steel brass aluminum sheets stainless steel amp pipe Noise build up Noise sound pressure level in the workplace can exceed 85 dB in this case sound insulation and hearing protection measures must be taken by the operator Initial Operating Always use the correct supply voltage The power supply voltage must match the info
4. ciency and may seriously overload the drill motor Inspect the drill bit often and replace it with a new bit as necessary Inspect the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened Should any of the screw be loose tighten them immediately Failure to do so could result in personal injury The brushes should be checked periodically and worn out brushes should be replaced in time After replacing inspect whether the new brushes can move freely in the brush holder Keep running the motor for 15 minutes to match the contact of the brushes and commutator Keep the ventilation slots clear from dirt clean off the accumulated dust and oll dirt periodically During normal operation if anything happens the power supply should be cut off at once and the tool should be checked and repaired CAUTION Only qualified serviceman can repair the tool O Wear hearing protection Wear eye protection Wear respiratory protection A WARNING To ensure safety and reliability all repairs should be performed by an authorized service center or other qualified service organization ENVIRONMENTAL PROTECTION waste Please recycle where facilities exist Check with your local sd Waste electrical products should not be disposed of with household Authority or retailer for recycling advice 1 PRT10538 01 CHUCK SCREW LEFT 3 PRT10538 03 KEYLESSCHUCK 4
5. es ensure these are connected and properly used Use of dust collection can reduce dust related hazards 4 Power tool use and care a Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it is designed b Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired c Disconnect the plug from the power source before making any adjustments changing accessories or storing the tool Such preventive safety measures reduce the risk of starting the tool accidentally d Store idle tools out of reach of children and other untrained persons Tools are dangerous in the hands of untrained users e Maintain tools with care Keep cutting tools sharp and clean Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control f Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control g Use the power tools accessories and tool bits etc in accordance with these instructions and in the manner intended for the particular type of power tools taking into account the working conditions and the work to be performed Use of the power tools for operations different from intended could result in a hazardous situation 5 Service
6. h 7 through to the left stop for loosening and unscrewing and nuts Mounting and removing the bit Fig 3 Insert the bit 16 into the keyless chuck 1 as far as it will go While holding stationary base of chuck with one hand tighten the moveable portion of the keyless chuck with your other hand until bit is firmly held in place Be sure that that the bit does not move and is held by all three jaws as you tighten the chuck Operating Never cover the ventilation slots 3 since they must always be open for proper motor cooling Drilling in wood To prevent ugly splits around the drill hole on the reverse side of the workpiece put a piece of scrap lumber under the work piece Drilling in metal Metals such as steel brass aluminum sheets stainless steel and pipe may also be drilled Mark the point to be drilled with a nail or punch Maintenance After use check the tool to make sure that it is in top condition It is recommended that you take this tool to a qualified Service Center for a thorough cleaning and lubrication at least once a year Do not make any adjustments while the motor is in motion Always disconnect the power cord from the receptacle before blade bit sanding paper etc lubricating or working on the unit Before performing any work on the drill itself unplug it from the power supply and inspect the drill bit Continued use of a worn and or damaged drill bit will result in reducing drilling effi
7. hock f If operating a power tool in a damp location is unavoidable use a residual current device RCD protected supply Use of an RCD reduces the risk of electric shock 3 Personal safety a Stay alert watch what you are doing and use common sense when operating a power tool Do not use tool while tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury b Use safety equipment Always wear eye protection Safety equipment such as dust mask non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce personal injuries c Avoid accidental starting Be sure switch is off before plugging in Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents d Remove adjusting keys or wrenches before turning the tool on A wrench or a key that is left attached to a rotating part of the tool may result in personal injury e Do not overreach Keep proper footing and balance at all times Proper footing and balance enables better control of the tool in unexpected situations f Dress properly Do not wear loose clothing or jewelry Contain long hair Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts g If devices are provided for the connection of dust extraction and collection faciliti
8. perating this product Save this instruction and follow them to reduce the risk of fire and personal injury 1 Work area a Keep your work area clean and well lit Cluttered benches and dark areas invite accidents b Do not operate power tools in explosive atmospheres such as in the presence of flammable liguids gases or dust Power tools create sparks which may ignite the dust or fumes c Keep bystanders children and visitors away while operating a power tool Distractions can cause you to lose control 2 Electrical safety a Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock b Avoid body contact with grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is grounded c Don t expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock d Do not abuse the cord Never use the cord to carry the tools or pull the plug from an outlet Keep cord away from heat oil sharp edges or moving parts Replace damaged cords immediately Damaged cords increase the risk of electric shock e When operating a power tool outside use an outdoor extension cord marked W A or W These cords are rated for outdoor use and reduce the risk of electric s
9. rmation quoted on the tool identification plate Switch Fig 1 This tool is started and stopped by pressing and releasing the switch 9 The speed can be adjusted in the high gear or in the low gear by controlling the on off pressing force Stepless Speed Control The machine runs with variable speed between 0 and maximum depending on the pressure applied to the switch 9 Ro Light pressure results in a low rotational speed thus allowing smooth controlled starts Do not load the machine so heavily that it comes to a standstill Speed Selection With the thumbwheel 8 the required speed can be selected also while running The required speed is dependent on the material and can be determined with practical trials After longer periods of working at low speed allow the machine to cool by running for approx 3 minutes at maximum speed with no load Continuous Use Switch on Press switch 9 and retain with lock button 10 Switch off Press and release switch 9 Changing the rotation direction Fig 2 Operate the rotation direction switch only at a standstill With the rotational direction switch 7 the rotational direction of the machine can be switched when the switch 9 is operated the rotation direction switch is locked Right Rotation Press the rotational direction switch 7 through to the right stop for drilling impact drilling riving screws etc Left Rotation Press the rotational direction switc
Download Pdf Manuals
Related Search