EFV Installation Manual
Contents
1. x 0 600 1600 ot oof of NOTES This is not approved for use with highest kW heater size Humidistat will reduce cooling air flow by 10 in high humidity Airflow is greater of COOL and HEAT when both electric heat and heat pump are operating ADJUST tap will increase airflow by 10 while tap will decrease airflow by 12 ADJUST tap TEST will cause the motor to run at 70 of full airflow Use this for troubleshooting only At the start of a call for cooling there is a short run at 82 of airflow for 7 5 minutes At the end of a call for cooling there is a blower delay of 1 minute Table 3 44876D006 Page 7 SEQUENCE OF OPERATION Cooling cooling only or heat pump Single Stage Cooling For single stage cooling Y1 and Y2 need to be jumpered When the thermostat calls for cooling the circuit between R and G is completed and the blower relay is energized The Normally Open contacts close causing the indoor blower motor to operate The circuit between R and Y is also completed this circuit closes the contactor in the outdoor unit starting the compressor and outdoor fan motor Circuit R and O energizes the reversing valve switching it to the cooling position The reversing valve remains energized as long as selector switch is in the COOL position Two Stage Cooling On a call for 19 stage cooling the thermostat close2. 18 1 18 O W2 18W wt 180 _ O H 00 oY2 18 ovo 16 Pin oY118Y oy d 18G 120 240 120 V When Applicable Wiring Diagram Variable Speed Blower Figure 4 44876D006 Page 13 Low Voltage Connections PSC Motor Thermostat Air Handler Thermostat Air Handler Heat Only Application Condensing Unit Cooling Only Application Thermosiat Air Handler Thermostat Air Handler Heat Pump Unit Condensing Unit Cooling Application with Electric Heat Connect common wire only if required See thermostat installation instructions Heat Pump Application with Electric Heat Figure 5 Page 14 44876D006 Limited Warranty August 1 1997 This warranty gives you specific legal rights and you may have other rights which vary from state province to state province Warrantor Armstrong Air Conditioning Inc 421 Monroe St Bellevue OH 44811 Armstrong Air Conditioning Inc products are available under t
3. Page 3 Condensate Drain Connection Do not operate unit without a drain trap The conden sate drain is on the negative pressure side of the blower therefore air being pulled through the con densate line will prevent positive drainage without a proper trap To avoid drain pan overflow the web must be re moved from inside any threaded drain pan hole to which a drain line is to be connected Use care when removing the web so as to not damage the coil On horizontal units the primary drain connection is flush with the bottom of the inside of pan Auxiliary connection is raised above the bottom of the inside of the pan Plastic web covering 3 4 auxiliary connection must be broken out if used Do not get primary and auxiliary connections interchanged When making drain fitting connections to the drain pan hand tighten only Overtightening the fittings can split connections on the drain pan The unit is provided with 3 4 FPT condensate drain connections e Connect the drain lines to the appropriate drain pan fittings e Secondary drain connections should be connected to a separate drainage system e Install a trap in the drain line below the bottom of the drain pan and pitch the drain lines down from the coil at least 1 4 per foot of run Horizontal runs over 15 long must also have an anti siphon air vent stand pipe installed ahead of the horizontal run An ex tremely long horizontal run may require an oversized
4. 6 Blower Performance Chart PSC Motor External Static Blower Pressure in wi 64 0595 ew ee fee EFC12 Table 2 Motor Board Taps and Dehumidify Resistor ADJUST NORM DEHUMIDIFY CUT TO ENABLE Figure 2 This model is designed for use with heat pumps as well as air conditioning systems The motor control board needs to sense a signal on the O thermostat wire in order to use cooling delay timing Fora 44876D006 straight air conditioning system connect O wire to the 24 volt wire The motor control board that provides airflow selection also features LED indicators that display operating mode humidity control and airflow CFM In addition thermostat signals for emergency heat EM aux heat W1 reversing valve compressor stage 1 Y1 compressor stage 2 Y2 and blower G are all indicated by lit LED s on this board If a humidistat is used the dehumidify LED will light when the humidistat opens and the motor runs at reduced airflow The control board also has a CFM LED that displays the operating CFM This red LED flashes once for each 100 CFM For example if the operating CFM is 1200 the CFM LED will flash 12 times then pause before repeating the 12 flash pattern Special note for units equipped with a humidistat If using a humidistat the dehumidify resistor located on the bottom right of the control board m
5. and all components are performance tested Each unit consists of a blower assembly optional refrigerant coil and controls in an insulated galvanized factory finished enclosure and may also include electric heat as specified Page 2 Knockouts are provided for electrical power wiring entrance When used on cooling applications excessive sweating may occur when unit is installed in a very humid space If installed in an unconditioned space sealant should be applied around the power wires control wires refrigerant tubing and condensate lines where they enter the cabinet Power wires should be sealed on the inside where they exit the conduit opening Sealant is required to prevent air leakage into and condensate from forming inside the unit control box and on electrical controls The unit must be installed in such a way as to allow free access to the coil compartment and blower control compartment The unit must be installed in a level position to ensure proper condensate drainage Make sure unit is level in both directions within 1 8 Units with circuit breakers installed in the vertical position must have breaker switch position ON in the up position and switch position OFF in the down position This is necessary to meet agency certification and National Electric Codes requirements Conversion to Vertical Downflow The EF furnace may be converted for vertical downflow applications The circuit breaker s must
6. drain line to eliminate air trapping e Route to the outside or to an appropriate drain Check local codes before connecting drain line to an existing drainage system e Insulate drain lines where sweating could cause water damage e The removal of cabinet knockouts required for drain connections can be made much easier with the indoor coil assembly removed from the cabinet e Install drain lines so they do not block service access to front of unit A 24 clearance is required for filter coil or blower removal and service access e sure unit is level or pitched slightly toward primary drain connection so that drain pan will empty completely without water standing in pan Page 4 Install a 2 trap in the primary drain line as close to the unit as practical Make sure that the top of the trap is below connection to the drain pan to allow complete drainage of pan Auxiliary drain if used should be run to a place where it would be noticeable if it becomes operational Occu pant should be warned that a problem exists if water should begin running from the auxiliary drain line Test condensate drain pan and drain line after installa tion is complete Pour several quarts of water into drain pan enough to fill drain trap and line Check to make sure drain pan is draining completely no leaks are found in drain line fittings and water is draining from the termination of the primary drain line Typical Conden
7. heating circuit and all heating will be electric heat jumper should be placed between W2 and E on the thermostat sub base so that the electric heat control will Page 8 transfer to the first stage heat on the thermostat This will allow the indoor blower to cycle on and off with the electric heat when the fan switch is in the AUTO position 44876D006 SYSTEM CHECK Pre start Check e properly located level secure and service able e Has an auxiliary pan been provided under the unit with separate drain for units installed above a finished ceiling all webs been carefully removed from the drain connections that are being used e Has the condensate line been properly sized run trapped pitched and tested e 15 the ductwork correctly sized run taped and insulated e Have all cabinet openings and wiring been sealed e 5 the indoor coil metering orifice size correct e Is the filter clean in place and of adequate size e Has the indoor outdoor unit application been reviewed for proper motor dip switch settings e 15 the wiring tight correct and to the wiring diagram e 5 the unit properly grounded and protected fused e 5 the thermostat correctly wired level in a good location e 5 the unit circuit breaker s rotated properly ON up OFF down e Are all access panels in place and secure Refer to outdoor unit installation instructions for system start up instru
8. HEAT 2nd STAGE HEATERS USED 18 BLK 5 KW HE1 4 12 133 7 5810 KW amp HE2 412 BLK 15 KW HE2 8 20 KW HE2 8 HE4 4 TB TERMINAL BLOCK OPT CB CIRCUIT BREAKER OPT Es 220 SEQ SEQUENCER 208 240 1st STAGE GND GROUND LUG VOLTAGE LS LIMIT SWITCH BY OTHERS HE HEATER ELEMENT lt lt POWER FACTORY WIRED POWER FIELD WIRED CONTROL FACTORY WIRED CONTROL FIELD WIRED CONTROL CIRCUIT WIRING TO BE 24 VOLT N E C CLASS 2 TO BLOWER GROUND LUG PLUG PIN AMP 350781 1 LOCATION 6 PIN CAP OOOT Q os TD TIME DELAY OPT TR TRANSFORMER BR BLOWER RELAY MTR BLOWER MOTOR CAP MOTOR CAPACITOR GND GROUND CONNECTION 14 BLK L1 14 YEL L2 THERMOSTAT BY OTHERS WIRING DIAGRAM NO HEAT WIRE NUTS BY OTHERS 14 BLU MED 14 RED LO 14 BLK HI 14YEL COM 15 AMP SUPPLY VOLTAGE 14 YEL 240V 14 WHT 120V MODELS 12 25 31 AND 49 i GROUND LUG WILL BE FACTORY SET TO LOW WHT IF 120V Wiring Diagram P N 065866900 Figure 3 Page 12 44876D006 _ 6 Plug _ Power Factory Wired A Control Factory Wired Transformer TRANS Blower Motor MTR Ground Connection GND Blower Relay BWR 14BK 11 Control Board 1 Thermostat 18 18
9. INSTALLATION AND MAINTENANCE INSTRUCTIONS EF Electric Furnace A WARNING Improper installation adjustment service or maintenance can Cause injury or prop erty damage Refer to this manual For assistance or additional information consult a qualified installer or service agency A WARNING The information contained in this manual is intended for use by qualified service techni cians familiar with safety procedures and equipped with the proper tools and test in struments Failure to carefully read and follow all instructions in this manual can result in equipment malfunction property damage personal injury and or death AWARNING Disconnect all power supplies to both the indoor blower section and outdoor section before making any electrical connections or servicing the system More than one discon nect switch may be required to de energize the equipment Hazardous voltage can Cause severe personal injury or death Manufactured By A Lennox International Company 421 Monroe Street Bellevue OH 44811 0650329 50 44876D006 Save these instructions for future reference Inspection of Shipment Upon receipt of equipment carefully inspect it for possible shipping damage If damage is found it should be noted on the carrier s freight bill Take special to examine the unit inside the carton if the carton is damaged Any concealed damage disco
10. ay limit application of sys tems without a ducted return to single story buildings e Install louvers in a closet Use the free area of louver or grille to determine the size opening required to provide the free area for metal louvers or grilles If the free area is not known assume 25 free area for wood or a 75 free area for metal louvers or grilles If the return air plenum is used the return air grille should be immediately in front of the opening in the plenum to allow for the free flow of return air When not installed in front of the opening there must be adequate clearance around the unit to allow for the free flow of return air Recommended Remote Filter Sizes Nominal Tons Air Conditioning amp Nominal Air Flow Up thru 2 Tons 800 900 CFM 2 1 2 Tons 900 1000 CFM 432 Square Inches 20 x 25 480 Square Inches 20 x 30 576 Square Inches 14 x 25 2 3 Tons 1300 1500 CFM 3 1 2 Tons 1300 1500 CFM 4 Tons 1500 1700 CFM 5 Tons 1900 2100 CFM 672 Square Inches 16 x 25 2 768 Square Inches 20 x 25 2 960 Square Inches 20 x 30 2 Table 44876D006 Nominal Size Disposable Filters Square Inch Surface Area Minimum Return Air Free Area amp Washable Filters 260 Square Inches 15 x 20 288 Square Inches 14 x 25 346 Square Inches 16 x 25 404 Square Inches 20 x 25 461 Square Inches 20 x 25 576 Square Inches 24 x 25 1
11. be rotated 180 To comply with certification and the National Electric Code units with circuit breakers installed in the vertical position must have circuit breakers installed so that the breaker switch ON position and marking is up and OFF position and marking is down All electric furnaces installed with a mating coil section must follow the instructions listed below for proper con densate drainage It is recommended that the auxiliary drain be connected to a drain line for all units If the auxiliary drain is not connected it must be plugged with provided cap For counterflow units the auxiliary drain must be connected and routed to a drain Horizontal Installations Horizontal installations can be left or right hand Adequate support must be provided to insure cabinet integrity Ensure that there is adequate room to remove service and access panels if installing in the horizontal position Refer to the air flow configuration drawings on page 11 for correct horizontal coil installations Ductwork and Airflow Maintain all required clearances to combustible surfaces as stated on the unit rating plate 44876D006 Supply and return ductwork must be adequately sized to meet the system s air requirements and static pressure capabilities Ductwork should be insulated with a minimum of 1 thick insulation with a vapor barrier in conditioned areas or 2 minimum in unconditioned areas Connect supply air duct to the f
12. bers MAINTENANCE Air Filters Important Do not operate system without a filter A filter is required to protect the coil blower and internal parts from excessive dirt and dust See unit position figures for location of filter in unit cabinet and service panel giving access to unit filter Inspect air filters at least once a month and replace or clean as required Dirty filters are the most common cause of inadequate heating or cooling performance Replace disposable filters Washable filters can be cleaned by soaking in mild detergent and rinsing with cold water Install new clean filters with the arrows on the side pointing in the direction of airflow Never replace a washable high velocity filter with a disposable low velocity filter unless return air system is properly sized for it Owner Record Furnace Model Serial Installation Date INSTALLED BY Dealer Address Telephone Contact Person Other Equipment Installed Equipment Type Model Serial License Installation Date Equipment Type Model Serial Installation Date Equipment Type Model Serial Installation Date Page 10 44876D006 AIRFLOW CONFIGURATIONS Counterflow Left to Right Airflow Right to Left Airflow Horizontal 44876D006 Page 11 PART 065866900 WIRING DIAGRAM ELECTRIC
13. ctions and refrigerant charging instructions Airflow For proper system operation the airflow through the indoor coil should be between 350 450 CFM per ton of cooling capacity Each electric furnace is shipped config ured to provide the correct airflow for the maximum tonnage outdoor unit If the electric furnace is to be used with smaller tonnage outdoor equipment the variable speed motor must be configured for that application by field changing the motor control board refer to the Appli cation Table on page 7 44876D006 Electric Heater To check the electric heater operation 1 Set thermostat to call for auxiliary heat approximately 5 F above ambient temperature The indoor blower and auxiliary heat should come on together Allow a minimum of 3 minutes for all sequencers to cycle on 2 the thermostat so it does not call for heat Allow up to 5 minutes for all sequencers to cycle off Page 9 REPLACEMENT PARTS Use only original equipment service parts when repairing these products These parts include but are not limited to circuit breakers heater controls heater limit controls heater elements motor blower relay control transformer blower wheel indoor coil and sheet metal parts When ordering replacement parts it is necessary to order by part number and include with the order the complete model number and serial number see unit data plate Refer to the parts list for unit component part num
14. he National Electric Code or Canadian Electric Code Improper installations not following these instructions can result in unsatisfactory operation and or dangerous conditions and may void the unit warranty General Information The EF electric furnace may be used with optional mating furnace coil cabinets in upflow counterflow or horizontal applications see AIRFLOW CONFIGURATIONS on page 11 for acceptable system configurations Tie plates and the necessary hardware are packaged with the blower sections to connect the furnace and coil section cabinets together To avoid drain pan overflow of coil cabinets the web must be removed from inside any threaded drain pan hole to which a drain line is to be connected Use care when removing the web so as to not damage the coil To avoid property damage caused by condensate drain blockage install a field fabricated auxiliary drain pan with a separate drain line to the outside under any indoor electric furnace where condensate overflow could occur If local building codes apply install per those codes Select the best position which suits the installation site conditions Take into consideration required clearances space routing requirements for refrigerant line conden sate disposal filters ductwork wiring and accessibility for service Refer to the unit specifications sheet and the unit rating plate for specific information These electric furnaces are completely factory assembled
15. he following names Air Ease Armstrong Air American Aire Concord Subject to the limitations stated in this warranty we warrant to the first buyer for use the residential heating cooling or heat pump unit when installed operated and maintained as required by this warranty to be free of defects in workmanship or material for a period of 5 years in residential installations 1 year in non residential installations from the time of installation We will replace any defective component without cost or expense to you except for the costs of delivery and labor for removal and replacement of the defective component Warranty Begins The warranty period begins when the installation is complete and the product is ready to operate You must be able to verify this date whenever a warranty claim is made Original bill of sale installer s invoice or other similar document will suffice If the beginning date cannot be verified we will consider warranty coverage to begin 6 months after the date the product was shipped from our factory Limitations on Implied Warranties Implied warranties of merchantability or to the extent applicable fitness for a particular purpose are limited to 5 years the same duration as the basic limited written warranty provided herein Some states provinces do not allow limitations on how long an implied warranty of merchantability or fitness lasts so the above limitations or exclusions may not apply to you Only Warranty T
16. his written Limited Warranty is the only warranty made by the warrantor this warranty is in lieu of and excludes all other warranties express or implied The warrantor does not authorize any person to provide any other warranty or to assume for it any further obligation in connection with the warranted product What is NOT Covered Cabinets or cabinet pieces Normal maintenance items such as filters fan belts fuses or other consumable items Damage caused by misuse failure to maintain properly accidents or acts of God External wiring piping venting or attachment of accessory products not integral to our product including without limitation humidifier air cleaner vent damper thermostat or other mechanical devices not manufactured by the warrantor Products that have been operated in a corrosive atmosphere where a concentration of acids halogenated hydrocarbons or other corrosive elements causes deterioration to metal surfaces or integral components NOTE Operation in a corrosive atmosphere is considered abuse and voids this warranty Products that have NOT been installed in accordance with our published installation instructions applicable local state provincial or national codes ACCA published standards Products that have NOT been installed by competent qualified installers Products that have been moved from their original place of installation Warranty on Replacement Components Any replacement component furnished by us w
17. ill assume the remaining unused portion of the Limited Warranty Consequential Damages The warrantor shall not be responsible for any consequential damages caused by any defect in the product Some state provinces do not allow the exclusion or limitations of incidental or consequential damages so the above limitation or exclusion may not apply to you NOTE After the first year in the event that a gas or oil heat exchanger is no longer being manufactured by the warrantor the warrantor will allow a credit equal to the then current wholesale price of an equivalent heat exchanger towards the purchase of a new Armstrong gas or oil furnace This product must be installed used and cared for in accordance with the instruction manual You are responsible for required periodic maintenance or service such as changing or cleaning of air filters and lubrication or cleaning of components Failure to properly install operate or maintain your unit voids this warranty 44876D006 Page 15
18. it must be grounded with separate ground connector s See the electrical connection diagrams beginning on page 12 for typical field wiring connection High voltage pigtail wiring connections are included in the unit For systems requiring additional electric heat this plug in harness will be discarded and the high voltage connection will be made on field wire points on the heater kit Low voltage control wiring are pigtail leads located outside the cabinet and are color coded to match the connection called out on the wiring schematic These units are designed for operation with a 208 240 volt single phase 60 cycle AC power supply The units are internally factory wired for 240 volt installation If 208 volt installation is desired it will be necessary to change the black transformer lead in the blower cabinet control box to the 208V terminal on the transformer IMPORTANT The variable speed motor in the EFV electric furnace contains DC filter capacitors that will cause a surge or inrush of current when power 15 applied Power is to remain applied to the motor except during servicing Remove AC power before plugging or unplugging the input power to the motor Do not install blower relays that interrupt line voltage to the motor 44876D006 Variable Speed Features The EFV electric furnace is equipped with a variable speed motor and will deliver a constant airflow within a wide range of external static pressures The variable speed bl
19. lange on top of the unit If an isolation connector is used it must be non flammable Sheet metal ductwork run in unconditioned spaces must be insulated and covered with a vapor barrier Fibrous ductwork may be used if constructed and installed in accordance with SMACNA Construction Standard on Fibrous Glass Ducts Check local codes for requirements on ductwork and insulation Duct system must be designed within the range of exter nal static pressure the unit is designed to operate against It is important that the system airflow be adequate Make sure supply and return ductwork grills special filters accessories etc are accounted for in total resistance Supply plenum is attached to the duct flanges supplied on the unit around the blower outlet Supply plenum should be the same size as the flanged opening provided around the blower outlet and should extend ideally at least 3 from the unit before turning or branching off plenum into duct runs The plenum forms an extension of the blower housing and minimizes air expan sion losses from the blower If an elbow is included in the plenum close to the unit it must not be smaller than the dimensions of the supply duct flange on the unit Non Ducted Return Closet Installation The cabinet can be installed in a closet with a false bottom to form a return air plenum or be installed with a return air plenum under the unit Louvers or return air grilles are field supplied Local codes m
20. ower offers the following comfort features Soft Start When called into operation the variable speed motor will slowly ramp up to normal operating speed This eliminates the noise and discomfort that results caused by the initial blast of air encountered with standard electric furnaces It can take up to 7 5 minutes to reach normal operating speed Continuous Blower Operation The comfort level of the living space can be enhanced when using this feature by allowing continuous circulation of air in between calls for cooling or heating The circulation of air occurs at 50 of the normal airflow rate 350 CFM minimum Reduced Airflow Operation For situations where humidity control is a problem the variable speed motor can be enabled to operate at a 10 reduction in the normal airflow rate This can be achieved by connecting to a standard humidity control that is normally closed and opens on humidity rise Page 5 SETUP PROCEDURE PSC Motor For proper cooling operation the airflow through the indoor coil should be between 350 and 450 CFM per ton 12 000 Btuh of cooling capacity based on the rating of the outdoor unit The cooling blower speed is factory configured to provide correct airflow for an outdoor unit that matches the maximum cooling capacity rating of the electric furnace the outdoor unit is smaller than the maximum cooling capacity rating for the electric furnace the cooling blower speed may need to be changed
21. s R to Y In 1 stage cooling the blower runs at 70 of the selected cooling airflow On a call for 27 stage cooling the thermostat closes R to Y2 In 2 stage cooling the blower runs at 100 of the selected cooling airflow Heating electric heat only When the thermostat calls for heat the circuit between R and W is completed and the heater sequencer is ener gized A time delay follows before the heating elements and the indoor blower motor come on Units with a second heat sequencer can be connected with the first sequencer to W on the thermostat sub base or connected to a second stage on the sub base Heating heat pump When the thermostat calls for heat the circuits between R and Y and R and G are completed Circuit R Y energizes the contactor starting the outdoor fan motor and the compressor Circuit R and G energizes the blower relay starting the indoor blower motor If the room temperature should continue to fall the circuit between R and W1 is completed by the second stage heat room thermostat Circuit R W1 energizes a heat se quencer The completed circuit will energize supplemental electric heat Units with a second heater sequencer can be connected with the first sequencer to W1 on the thermostat or connected to a second heating stage W2 on the thermostat sub base Emergency Heat heating heat pump If selector switch on thermostat is set to the emergency heat position the heat pump will be locked out of the
22. sate Drain Connection ee aaa Drain Connection 1 00 Min 2 0 Min Positive Liquid Seal Required Figure 1 A CAUTION A field fabricated auxiliary drain pan with a drain pipe to the outside of the building is required in all installations over a finished living space or in any area that may be damaged by overflow from the main drain pan In some localities local codes may require an auxiliary drain pan for any horizontal installation 44876D006 Electrical Wiring AWARNING Turn off electric power at the fuse box or service panel before making any electrical connections and ensure a proper ground connection is made before connecting line voltage Failure to do so can result in prop erty damage personal injury or death All field wiring must be done in accordance with National Electrical Code recommendations local codes and applicable requirements of UL or in accordance with the Canadian Electrical Code local codes and CSA Stan dards Power wiring disconnecting means and over current protection are to be supplied by the installer See he unit rating plate for unit maximum over current protec tion minimum circuit ampacity and operating voltage The power supply must be sized and protected according to the specifications supplied Use of multiple supply circuits require grounding of each circuit to lug s provided in unit Use copper conductors only The un
23. see Table 2 IMPORTANT The cooling blower speed must be set to provide a minimum of 350 CFM airflow per ton 12 000 Btuh of outdoor cooling capacity Changing Blower Speed 1 Disconnect all power supplies 2 Remove the electric furnace access panel 3 Locate pin number 2 on the blower relay Two black wires are connected to this terminal pin One connects to pin number 5 on the blower relay and the other connects to an inline splice connected to a red or black wire 4 Remove the wire going to the 4 pin blower motor connector from the splice 5 Connect the blower lead Red LO Black HI to the splice from the 4 pin blower motor connector Unused blower speeds are shipped from the factory covered with a plastic cap Remove the cap from the new blower speed terminal and place it over the factory set blower terminal 6 Replace electric furnace access panel 7 Reconnect power Variable Speed Motor Locate the motor control board in the blower control box Set the HEAT and COOL CFM taps by moving the board jumpers to the A B C or D positions see Figure 2 based on the information found in the Application Table on page 11 The ADJUST tap on the control board can be used to raise or lower the table The tap will raise the table CFM by 10 and the tap will lower the table CFM by 12 IMPORTANT When changing the control taps the high voltage must be off in order for the new settings to take effect Page
24. ust be removed see Figure 2 The HUM terminal on the board must be connected to the Normally Closed contact of the humidistat so that the board senses an open circuit on high humidity Application Table The versatility of the variable speed motor enables the performance of the EFV electric furnace to be tailored to the different modes of operation encountered in heating and cooling All EFV electric furnaces are capable of operation at more than one nominal airflow rate The operation of an EFV blower at different airflow rates is determined by the control board taps and the thermostat see the Application Table below Before beginning the setup become familiar with the information found in this table The data in the application table is categorized by unit size and mode of operation Use the information provided to determine the CFM taps needed for cooling and heating Variable oes Motor Application Table Thermostat Control Board Taps COOL HEAT x 600 so aofa 700 x x _ 1100 100 x cooing x x 600 400 1200 wooo sevem pening e reco rao ooo SO x x 1400 _ e
25. vered should be reported to the last carrier immediately preferably in writing and should include a request for inspection by the carrier s agent If any damages are discovered and reported to the carrier DO NOT INSTALL THE UNIT as claim may be denied Check the unit rating plate to confirm specifications are as ordered TABLE OF CONTENTS INSTALLATION SETUP PROCEDURE SEQUENCE OF OPERATION SYSTEM CHECK REPLACEMENT PARTS MAINTENANCE AIRFLOW CONFIGURATIONS WIRING DIAGRAMS WARRANTY Page 1 INSTALLATION This EF electric furnace is designed for ease of installation featuring horizontal upflow and downflow counterflow applications The units are shipped from the factory completely assembled Accessories may also be ordered as field installed items All models are designed for indoor installations only Read the entire instruction manual before starting the installation Several of the installation steps can be done prior to setting the unit in place and doing this can save time and simplify installation Do not remove the cabinet knockouts until it has been determined which knock outs will need to be removed for the installation Determining which knockouts to remove will depend on application and in some cases preference These instructions are intended to be a general guideline and do not supersede any local or national codes Installation must conform with the local building codes and with the latest editions of t
Download Pdf Manuals
Related Search