Home

Toshiba MV13P2 13 in. TV/VCR Combo

1. REC SET AUTO REPEAT A 4 gt MENU NOTE To cancel auto repeat function follow above steps 1 and 2 then press lt or to select OFF Press MENU to return to the TV The auto repeat function is canceled automatically when the unit is switched off or the tape is ejected 5L80101C P34 43 38 20 4 04 16 22 RECORDING A TV PROGRAM RECORDING AND VIEWING THE SAME TV PROGRAM To turn on the TV VCR press POWER Load a cassette tape with the erase prevention tab intact Press SPEED to select the desired tape speed Set the TV CABLE selection to the appropriate SP or SLP The counter and SP or SLP will ap position see page 22 pear on the screen about 4 seconds TV VHF UHF channels CABLE Cable TV channels 00 00 00 SP NOTES If power is switched off during recording the TV set goes off and the VCR continues to record Press STOP to halt the recording and turn off the VCR The TV VCR Channel cannot be changed during recording 5L80101C P34 43 39 20 4 04 16 22 RECORDING A TV PROGRAM CONTINUED Press Direct channel selection 0 9 or CH Press both REC at the same time or to select the channel to be recorded Exam and the channel number will appear the ple Channel 12 Screen and the REC indicator will light PE REC PAUSE STILL STOP TO STOP
2. OWNER S MANUAL TO S H TELEVISION VCR COMBINATION MV13P2 E oooooooo es ATTENTION If you purchase a universal remote control from your local retailer please contact the remote manufacturer for the required programming code TV CABLE MODE SELECTION When shipped from the factory the TV CABLE selection is set to the CABLE Cable Television position If not using Cable TV set this selection to the TV position VHS Before operating the unit please read this manual thoroughly 5L80101C COV IN 1 20 4 04 16 18 The lightning flash with arrowhead symbol within an equilateral triangle is CAUTION intended to alert the user to the presence RISK OF ELECTRIC SHOCK of uninsulated dangerous voltage within DO OPEN the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock CAUTION TO REDUCE THE RISK OF ELECTRIC The exclamation point within an equilateral SHOCK DO NOT REMOVE COVER triangle is intended to alert the user to OR BACK NO USER SERVICEABLE the presence of important operating and PARTS INSIDE REFER SERVICING TO maintenance servicing instructions in QUALIFIED SERVICE PERSONNEL the literature accompanying the appliance WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE WARNING CAU
3. o BSE CLOCK SET CLOCK SET A T MENU Press the A or V to select one of the options then press ENTER Press MENU repeatedly until the menu screen is cleared for manual setting forward one hour for manual setting back one hour for automatic setting read EDS in the signal DAYLIGHT SAVING TIME ON p When you want to set the daylight saving time manually T on the first Sunday in April you set to ON and on the last A Y ENTERMENU Sunday in October you set to OFF NOTES When shipped from factory DAYLIGHT SAVING TIME is set to AUTO When the clock is not set daylight saving time setting is not available When there is no daylight saving time in your area always select OFF in step 3 16 5L80101C P10 19 16 20 4 04 16 19 MANUAL CLOCK SETTING You must set the date and time manually for timer recordings ON OFF timer and daylight saving time if the auto clock process did not set them correctly EXAMPLE Setting the clock to 8 30 AM 27th SAT March 2004 Press MENU Press A or V to select CLOCK SET then Press 4 or to select option press gt ET E CLOCK SET CLOCK SET SAVING TIME AJ V i MENU Press
4. TH AM m VJ L VY lw V 8 9 10 11 12 13 14 REAR 15 16 DESCRIPTION OF CONTROLS FRONT 1 Cassette loading slot To insert or remove a video tape 2 POWER button Press to turn the TV VCR on or off 3 TIMER REC indicator Lights when the unit is in the Timer Record Mode 4 REC indicator Lights up when the TV VCR is recording 5 PLAY button Press to play a prerecorded tape 6 REW Rewind button In the Stop mode this button rapidly winds the tape backwards In the Play mode this button activates reverse search 7 PHONE jack Plug monaural headphones or an earphone with an 1 8 miniplug into this jack for private listening 8 Remote sensor Signals from the Remote Control are received here 9 REC button Press once to start normal recording Additional presses activate One touch Timer Recording 8 5L80101C 01 09 8 10 VOLUME A V buttons Press to raise or lower the volume of the sound 11 CHANNEL A Y buttons Press to select a channel for viewing or recording 12 STOP EJECT button Press once to stop the tape in any mode Press again to eject the tape 13 FF Fast Forward button In the Stop mode this button rapidly winds the tape forward In the Play mode this button activates forward search 14 AUDIO VIDEO IN jacks Audio and video signal cables from an external source can be connected here REAR 15 UHF VHF antenna jack
5. Additional press increases the INDEX No up to 9 When the INDEX or is pressed the unit starts searching the INDEX No selected and finds the portion then playback starts automatically To stop the index search press STOP INDEX STOP TV MONITOR TO MONITOR A TV PROGRAM Press TV MONITOR while in the playback mode The video tape will continue to play while the picture switches to the TV channel selected on the TV VCR Press the button to return to the playback picture TV MONITOR NOTES When you record an INDEX mark at the very beginning of the tape the mark may not be found During INDEX search the tape may stop and begin to play at a slightly different location INDEX may not function properly with old or worn out video tapes INDEX marks may not be found if it is extremely close to the point where the search began In recording if you stop recording temporarily the INDEX mark is not recorded on the tape 47 5L80101C P44 BACK 47 20 4 04 16 23 DUPLICATING A VIDEO TAPE If you connect the TV VCR to another VCR or Camcorder you can duplicate a previously recorded tape Make all connections before turning on the power Insert a blank cassette with the erase preven Press INPUT SELECT to select AUDIO tion tab intact into the TV VCR VIDEO input position LINE will appear on Insert a previously recorded cassette into the the screen playback VCR or Cam
6. Ti 0 Antenna Antenna jack jack 75 ohm coaxial 300 75 ohm cable matching transformer Connect the 75 ohm cable from the combination VHF UHF antenna to the antenna jack If your combination VHF UHF antenna has a 300 ohm twin lead wire the use of the 300 75 ohm matching transformer may be necessary Combination VHF UHF antenna Separate VHF and UHF 300 ohm twin lead wires 300 75 ohm matching ANT transformer LG jack A Combiner 300 VHF 300 ohm Connect the UHF 300 ohm twin lead wire to the combiner not supplied Connect the VHF 300 ohm twin lead wire to the 300 75 ohm matching trans former Attach the transformer to the combiner then attach the combiner to the antenna jack Separate VHF UHF antennas 75 ohm VHF cable and 300 ohm UHF twin lead wires ANT O Antenna jack VHF 75 ohm Combiner UHF 300 ohm 5L80101C P10 19 11 Connect the VHF 75 ohm cable and UHF 300 ohm twin lead wire to the combiner not supplied Attach the combiner to the antenna jack 11 20 4 04 16 19 TV CONNECTIONS This TV VCR has an extended tuning range and can tune most cable channels without using a Cable TV converter box Some cable companies offer premium pay channels in which the signal is scrambled Descrambling these signals for normal viewing requires the use of a descrambler device which is gener all
7. e f you want to correct the digits while setting press or until the item you want to correct then press lt or gt to correct the desired setting 29 5L80101C P20 33 20 4 04 16 21 5L80101C P20 33 70 SET THE OFF TIMER This feature allows you to have the TV VCR turn OFF automatically at a predetermined time If you program the OFF TIMER once the TV VCR will automatically turn off at the same time everyday EXAMPLE Turning off the TV at 11 30 PM Press MENU Press 4 or to select option SAVING TIME AL VI 4I E MENU Press 4 or to set the de sired hour then press V gt ONTIMER 12 00AM CH 001 SUN SAT CANCEL gt OFFTIMER 71i 00PM CANCEL 4 4 gt ENTER MENU Press A or V to select ON OFF TIMER then press gt 2 CLOCK SET gt gt gt gt gt AI VIE IMENU Press lt or set the desired minute then press V gt ONTIMER 12 00AM CH 001 SUN SAT gt OFFTIMER 113308M A 4 gt ENTER MENU Press A or V to select OFF TIMER then press gt ONTIMER 12 00AM CH001 SUN SAT gt OFFTIMER 12 00AM Press 4 to select SET then press MENU repeatedly until t
8. Connect the 75 ohm coaxial cable from the antenna or Cable TV service to this jack 16 AC power cord Connect to a 120V 60Hz outlet 20 4 04 16 19 S REMOTE CONTROL 10 11 12 13 14 15 5L80101C 01 09 9 CLOSED INPUT CAPTION SELECT POWER ZERO PROGRAM SPEED RETURN CANCEL OO C2 DIGITAL TRACKING TRACKING inex f CFT REW EJECT STOP CLOSED INPUT CAPTION SELECT POWER SKIP SEARCH CD C CD TV MONITOR DOOD DO CHANNEL CALL ZERO PROGRAM SPEED RETURN CANCEL SS lt lt SLEEP FES amp gt DIGITAL PRE TRES C INDEX PLAY Gc e REW iN 2 STOP DESCRIPTION OF CONTROLS CLOSED CAPTION button Switches between Caption Text and TV modes for Closed Captioned programs Direct channel selection buttons 0 9 Allows direct access to any channel CALL button Displays the present time day of the week channel counter speed selection and VCR mode if VCR is operating on the TV screen PROGRAM button Press to confirm the programmed timer recording and ON OFF timer MENU button Press to display the On Screen menu function DIGITAL TRACKING button Allows automatic adjust ment of tracking to minimize picture noise during playback EJEC
9. This TV VCR is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory skipping over unwanted channels Before selecting channels they must be programmed into the TV VCR s memory In addition to normal VHF and UHF channels this TV VCR can receive up to 113 Cable TV channels To use this TV VCR with an antenna set the TV CABLE selection to the TV position When shipped from the factory this selection is in the CABLE position TV CABLE SELECTION Press MENU Press 4 or to select option 2 TVICABLE CABLE AUTO CH MEMORY gt ADD DELETE Cable TV chart The chart below is typical of many cable system channel allocations Number on this TV 14 15 16 17 18 19 20 21 22 Corresponding Cable TV channel A B C D E F G H I 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 J K L M N O P Q S T U V W AA BB CC DD 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 EE FF GG HH Il JJ KK LL MM NN OO PP QQ RR SS UU VV 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 WW CCC DDD FFF GGG HHH JJJ KKK LLL MMM NNN OOO PPP QQQ 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 RRR SSS UUU VVV WWW YYY ZZZ 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 A 5 A 4 A3 A 2
10. 0 9 ENTER CANCELMENU PASSWORD Enter the password using Direct channel selection 0 9 then press ENTER V CHIP SET PASSWORD 0 9 ENTER CANCEL MENU Press A or V to select CHANGE PASSWORD then press gt T ul E V CHIP V CHIP SET CHANGE PASSWORD AL V IMENU Enter the new password using Direct channel selection 0 9 then press ENTER C EE CHANGE PASSWORD NEW PASSWORD yems 0 9 ENTER CANCEL MENU Enter the same password again to confirm then press ENTER Ky Da CHANGE PASSWORD CONFIRM PASSWORD 0 9 ENTER CANCEL MENU Press MENU repeatedly until the menu screen is cleared 5L80101C P20 33 28 20 4 04 16 21 To SET THE ON TIMER This feature allows you to have the TV VCR automatically turn ON at a predetermined time If you program the ON TIMER once the TV VCR will turn on on the programmed day daily weekly at the same time to the same channel EXAMPLE Turning on the TV to channel 12 at 7 00 AM MONDAY FRIDAY Press MENU Press 4 or to select option gt gt gt gt DAYLIGHT SAVING TIME gt AIYA MENU Press lt or to set the
11. LE PROBLEM AND TROUBLESHOOTING GUIDE Check the following chart before requesting service SYMPTOM CAUSE POSSIBLE SOLUTION POWER No power The AC power cord is not connected Connect the AC power cord to the AC outlet Although the power is on the TV VCR does not operate Cassette is not inserted Insert a video cassette TIMER REC buttons are depressed Press the TIMER REC buttons TV BROADCAST RECEPTI ON Poor or no picture TV station experiencing problems Try another channel Picture control is not adjusted Check picture control adjustments Possible local interference Check for source of reception disturbance Antenna CABLE connector is not connected or possible local interference Check CABLE connection or VHF UHF antenna reposition or rotate antenna Poor or no color TV station experiencing problems Try another channel Picture control is not adjusted Check picture control adjustments Possible local interference Check for source of reception disturbance Antenna CABLE connector is not connected or possible local interference Check CABLE connection or VHF UHF antenna reposition or rotate antenna Picture wobbles or drifts TV station experiencing problems Try another channel Antenna CABLE connector is not connected or possible local interference Check CABLE connection
12. NOTES The starting setup function will work only when you press the POWER button for the first time The auto clock function uses the EDS Extended Data Service information carried on the channel signal If the antenna signal is weak or there are no channels with EDS informations the auto clock function may not set the time In this case you must set the clock manually see page 17 AUTO CLOCK setting it may take more than 10 minutes to read the EDS signal for one 1 3 channel which has only Time of day or Local time zone 5L80101C P10 19 13 20 4 04 16 19 SETTING THE LANGUAGE This TV VCR can display the on screen language in English Spanish or French Select the language you prefer first then proceed with the other menu options Press MENU Press A or V to select LANGUAGE then Press 4 or select option press gt LANGUAGE LANGUAGE IDIOMA LANGUE IDIOMA LANGUE PICTURE PICTURE PICTURE PREFERENCE PICTURE PREFERENCE o EE F3 m E EE ed 5 gt A 4 gt MENU A VIE MENU Press or to select the desired language Press MENU repeatedly until the MENU screen English ENGLISH Spanish ESPANOL or is cleared French FRANCAIS then press ENTER 65 LANGUAGE IDIOMA LANGUE ENGLISH ESPAN
13. position tune your TV VCR to the output of the converter descrambler box usually channel 3 or 4 and use the converter descrambler box to tune scrambled channels Converter Incoming descrambler 75 ohm 75 ohm cable A Cable TV cable to TV VCR NT Splitter A B Switch Q Antenna jack 5L80101C P10 19 12 20 4 04 16 19 0 STARTING SETUP The STARTING SETUP function makes installing your TV VCR easily It leads you the Language selection TV CABLE selection auto channel memory and auto clock setting automatically IMPORTANT Make sure that the antenna or cable TV system connection is made Press POWER Press A or V to select TV or CABLE The starting setup function begins and the then press ENTER Language setup menu appears on the screen Press A or V to select your desired language then press ENTER POWER A G Ta LANGUAGE IDIOMA LANGUE CHANNEL PLAN ENGLISH ESPA OL FRANCAIS lt A W ENTER gt lt A W ENTER gt CANCEL Press A or V to select START then press Now the AUTO CH MEMORY starts ENTER After it completed the AUTO CLOCK starts If you select CANCEL and press ENTER the automatically After the starting setup is com STARTING SETUP stops and changes to the TV pleted the TV channel appears on the screen Screen ENTER AUTO SETUP AUTO CH MEMORY AUTO CLOCK START STOP CANCEL STOP CANCEL CANCEL lt A W ENTER gt
14. Adjustment Turn on the TV VCR Press MENU Press 4 or gt to select ft option Press A or V to select AUTO CLOCK Press 4 or to select OFF Press MENU repeatedly until the menu screen is cleared When the AUTO CLOCK is set to OFF the auto clock adjustment does not function Set the clock manually see page 17 TO SET STANDARD TIME In the rare event that you live within broadcast range of two stations in two different time zones the TV VCR may recognize the wrong station for the auto clock set To correct the situation 1 Press MENU 2 Press 4 or to select option 3 Press A or V to select STANDARD TIME then press gt 4 Press A W amp to select your time zone then press ENTER ATLANTIC GMT 4 hours GMT Greenwich Mean Time EASTERN GMT 5 hours CENTRAL GMT 6 hours MOUNTAIN GMT 7 hours PACIFIC GMT 8 hours ALASKA GMT 9 hours HAWAII GMT 10 hours AUTO AUTO SET 5 Press MENU repeatedly until the menu screen is cleared NOTE To be able to select the standard time the clock must first be set by AUTO CLOCK once 5L80101C P10 19 15 20 4 04 16 19 AuTo CLOCK SETTING CONTINUED DAYLIGHT SAVING TIME SETTING You can set the daylight saving time automatically or manually Press MENU Press 4 or to select 7 option Press A or to select DAYLIGHT SAVING TIME then press gt
15. RECORDING TO STOP RECORDING TEMPORARILY Press STOP to stop recording Press PAUSE STILL to avoid recording unwanted material fi will appear on the screen and the channel number will appear on the screen and the REC indicator will blink on and off Press PAUSE STILL or both REC to continue the recording PAUSE STILL cHote NOTE The pause mode will be changed to the stop mode after five minutes to prevent damage to the tape NOTES AUTO REWIND FEATURE This TV VCR will automatically rewind the video cassette when the tape has ended except during OTR and timer recording It will also eject the video cassette If the erase prevention tab is removed the tape will eject when both REC are pressed for recording 5L80101C P34 43 40 20 4 04 16 22 0 ONE TOUCH TIMER RECORDING OTR The One touch Timer Recording feature provides a simple and convenient way to make a timed recording EXAMPLE One touch Timer Recording for 30 minutes Press POWER to turn on the Load a video cassette Press SPEED to select the TV VCR with the erase prevention desired tape speed SP or tab intact SP or SLP will appear on the screen SPEED 00 00 00 SP Set the TV CABLE selec Press Direct channel Press both REC at the same tion to the appropriate selection 0 9 or CH or time to begin recording position see page 22 to select the channel to be Press the buttons a
16. TIMER REC NOTES VCR section cannot be used while the TIMER REC indicator is lit If you want to use the VCR operation press both TIMER REC at the same time to deactivate the timer After a power failure or disconnection of the power plug all programed recording setting and time display will be lost upon resumption of power In this case reset the clock see pages 15 17 and reprogram any timer recordings 43 5L80101C P34 43 43 20 4 04 16 22 OTHER FUNCTIONS FOR THE TIMER RECORDING TO SET DAILY WEEKLY TIMER TO CONFIRM THE SETTINGS When setting the date in the step 4 on page 42 press Press PROGRAM once The TV screen displays the 4 repeatedly timer program list The setting changes as follows Press PROGRAM again The TV screen displays the ON OFF timer setting Example The current day Friday SUN SAT Sunday to Saturday once twice PROGRAM 23 TH 7 00PM 9 30PM 007 SLP A MON SAT Monday to Saturday gt ON TIMER 12 00AM One month later minus one day MON FRI Monday to Friday CANCEL CANCEL V ENTER CANCELMENU A YIP MENU WKL FRI lt WKL THU Weekly Thursday Weekly Friday Press PROGRAM 3 times The screen returns to the normal screen PROGRAM CANCEL TO CANCEL A PROGRAM IF THE PROGRAM OVERLAPS ANOTHER Select 09 option in the menu NOTE Do not overlap programs as portions of the Press A or V to select TIMER REC SET
17. alternating current line plug your unit may be equipped with a 3 wire grounding type plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This too is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the grounding type plug 5L80101C 01 09 1 20 4 04 16 18 a fe IMPORTANT SAFEGUARDS _ 12 POWER CORD PROTECTION Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the appliance 13 LIGHTNING To protect your unit from a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the unit due to lightning and power line surges 14 POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines other electric light or power circuits or where it can fall onto or against such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal 15 OVERLOADING Do not overload wall ou
18. channels VHF 2 13 UHF 14 69 Cable TV 14 36 A W 37 59 AA WW 60 85 AAA ZZZ 86 94 86 94 95 99 A 5 A 1 2 1 100 125 100 125 01 5 Antenna input VHF UHF In 75 ohms coaxial Speaker 1 1 2 x 2 11 16 inches 38 x 69 mm 8 ohm Audio output power 1 5W VCR Video system VHS 2 rotary heads helical scanning system Video signal NTSC color Cassette tape VHS Audio track 1 track Tape speed SP 33 35 mm sec SLP 11 12 mm sec F FWD REW time F FWD Approx 4 minutes 50 seconds T 120 cassette at 25 C 77 F REW Approx 2 minutes 30 seconds T 120 cassette at 25 C 77 F Speed search SP 3 amp 5 x normal speed SLP 9 amp 15 x normal speed GENERAL Power source AC 120V 60Hz Power consumption 65 Watts Dimensions Width Height Depth 14 1 4 inches 362 mm 15 1 16 inches 382 mm 14 3 8 inches 365 mm Weight 24 3 Ibs 11 kg Terminals Video In RCA 1 Vp p 75 ohm Audio In RCA 8 dBm 50k ohm Storage temperature 20 C to 60 C 4 F to 140 F Operating temperature 5 C to 40 C 41 F to 104 F Remote control Infrared direct access 2 x AAA batteries Accessories 300 75 ohm matching transformer Remote control Batteries 2 x AAA Specifications are subject to change without notice Tape Speed shown is approximate 52 5L80101C P44 BACK 52 20 4 04 16 23 LIMITED WARRANTY TOSHIBA COMBINATION TELEVISION A
19. desired hour then press V i 03 og CANCEL CANCEL AL V 4I b ENTER MENU Press A or V to select ON OFF TIMER then press gt 00 CLOCK SET gt gt DON gt 2 SAVING TIME AI VIE MENU Set the desired minute channel and daily or weekly timer date as in step 4 gt QFFTMER 5 12 00AM CANCEL 4 4 gt ENTER MENU Press A or V to select ON TIMER then press gt E E ON TIMER 12 00AM CH 001 SUN SAT gt OFFTIMER 12 00AM MENU Press lt or to select SET then press ENTER Press MENU repeatedly until the menu screen is cleared ENTER aH gt ONTIMER 7 00AM CH012 MON FRI gt OFFTIMER 12 00AM A 4 gt ENTER MENU NOTES The TV VCR will automatically turn off approximately 1 hour later after the ON TIMER turns on To continue watching the TV press any button to cancel the one hour automatic shut off cancel TIMER follow above steps 1 5 then press lt or to select CANCEL Press MENU repeatedly until the menu screen is cleared After setting the ON TIMER the selected cursor on to OFF TIMER If you wish to set the OFF TIMER press gt then follow the steps 4 6 on page 30
20. home when warranty service is required Depending on the type of repair required the service will either be performed in your home or the set will be taken to the TACP Authorized Service Station for repair and returned to your home at no cost to you In the Continental United States contact Toll Free 1 800 631 3811 All warranties implied by state law including the implied warranties of merchantability and fitness for a particular purpose are expressly limited to the duration of the limited warranties set forth above With the exception of any warranties implied by state law as hereby limited the foregoing warranty is exclusive and in lieu of all other warran ties guarantees agreements and similar obligations of manufacturer or seller with respect to the repair or replace ment of any parts In no event shall TACP be liable for consequential or incidental damages No person agent distributor dealer or company is authorized to change modify or extend the terms of these warranties in any manner whatsoever The time within which action must be commenced to enforce any obliga tion of TACP arising under this warranty or under any statute or law of the United States or any state thereof is here by limited to 90 days from the date you discover or should have discovered the defect This limitation does not apply to implied warranties arising under state law This warranty gives you specific legal rights and you may also have other ri
21. or VHF UHF antenna reposition or rotate antenna Cable TV channel is scrambled Try another channel No CABLE reception CABLE connector is not connected Check all CABLE connections TV CABLE selection is set to TV Set the TV CABLE selection to CABLE Cable TV service interrupted Contact your Cable TV company No reception above channel 13 TV CABLE selection is not set to the appropriate position Make sure TV CABLE selection is in the appropriate position UHF antenna is not connected Check UHF antenna Poor or no sound 50 5L80101C P44 BACK TV station experiencing problems Try another channel Antenna CABLE connector is not connected or possible local interference Check CABLE connection or VHF UHF antenna reposition or rotate antenna Possible local interference Check for source of reception disturbance MUTE button is depressed i Check that MUTE button has not been pressed 20 4 04 16 23 SYMPTOM CAUSE POSSIBLE SOLUTION TV shuts off TV station stopped broadcasting Tune new channel Sleep timer is set Set Sleep Timer to 0 OFF timer is set Set OFF TIMER to CANCEL Closed caption is not activated TV station experiencing problems or program tuned is not closed captions Try another channel TV signal is weak Check CABLE connection of VH
22. personal preferences set by you see Picture control adjustments on previous page 5L80101C P20 33 32 20 4 04 16 21 AND UNLOADING VIDEO CASSETTE Use only video cassette tapes marked VHS LOADING Push the center of the tape until it is automatically retracted into the TV VCR AUTOMATIC POWER ON AND PLAY When loading a cassette tape without the erase prevention tab intact the TV VCR will turn on automatically and playback will start immediately Insert the cassette with its labeled side facing you An inverted video cassette cannot be inserted p a UNLOADING To unload a video cassette press EJECT on the remote control or press STOP EJECT on the TV VCR twice The first press will stop the tape in any mode The second press will eject the tape STOP EJECT EJECT AUTOMATIC EJECT If the TV VCR automatically rewinds the tape to the beginning AUTO REWIND FEATURE the tape will be ejected automatically See NOTE on page 40 NOTES Always eject the tape when not in use The cassette tape can be ejected even if the POWER is OFF 5L80101C P20 33 33 20 4 04 16 22 AND UNLOADING A VIDEO CASSETTE CONTINUED TO PREVENT ACCIDENTAL ERASURE TO RECORD AGAIN After recording break off the erase prevention tab if Cover the hole with adhesive tape you do not wish to record o
23. 4 or to set the Set the day year and time After setting the clock date and time month then press V as in step 3 then press starts functioning automatically ENTER BE 8 30 AM SAT CLOCK SET CLOCK SET M 12 00AM A 4 gt ENTERMENU A 4 gt ENTER MENU NOTES After a power failure or disconnection of the power plug the time display will be lost In this case set the present time again if the auto clock did not set correctly To move cursor backward press A 5L80101C P10 19 17 20 4 04 16 19 rt tll LE OPERATION To turn on the TV VCR Adjust the volume level by Set the TV CABLE selection press POWER pressing VOL or to the appropriate position The volume level will be see page 22 indicated on the screen by green bars As the volume level increases so do the number of bars If the volume decreases the number of green bars also decreases TV VHF UHF Channels CABLE Cable TV Channels VHF UHF CABLE CHANNELS TV CABLE VHF VHF 2 13 2 13 UHF STD HRC IRC 14 69 14 36 A W 37 59 AA WW 60 85 AAA ZZZ 86 94 86 94 95 99 A 5 A 1 100 125 100 125 01 5A Press Direct channel selection 0 9 to select the channel TV mode direct channel selection When t
24. A 1 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 01 113 114 115 116 117 118 119 120 121 122 123 124 125 Press A or V to select Press lt or gt to select TV Press MENU repeatedly until TV CABLE or CABLE The arrow the menu screen is cleared indicates the selected position Dal Ei 2 TV CABLE P CABLE AUTO CH MEMORY ADD DELETE gt TV VHF UHF channels CABLE Cable TV channels AL V A IP MENU 5L80101C P20 33 22 20 4 04 16 20 l AUTOMATIC MEMORY TUNING Press MENU Press A or V to select AUTO CH MEMORY Press 4 or gt to select option then press al Ba TVICABLE CABLE TVICABLE gt CABLE AUTO CH MEMORY AUTO MEMORY gt ADD DELETE gt ADD DELETE A TA IMENU a gt MENU The TV VCR will begin memorizing all the Press MENU repeatedly until the menu screen channels available in your area Channel is cleared numbers will remain red until auto memorizing is complete 5L80101C P20 33 23 20 4 04 16 20 MEMORIZE CHANNELS CONTINUED TO ADD DELETE CHANNELS Press MENU Press 4 or P to select E Press A or V to select option AD
25. CLOSED CAPTIONING WITH A VCR Closed captioned programs can be recorded and played back on a VCR with the closed captioned text intact The closed captioned text will disappear during cue fast forward search review eewind search and pause modes or if the VCR tracking is not adjusted properly TO VIEW CLOSED CAPTIONS Press CLOSED CAPTION on the remote control to Switch between normal TV and the two closed caption modes captions and full screen text Captions This closed caption mode will display text on the screen in English or another language depend ing on the setting of the closed captions CH 1 or 2 Generally closed captions in English are transmitted on captions channel 1 and closed captions in other languages are transmitted on captions channel 2 Text The text closed caption mode will usually fill the Screen with a programming schedule or other information After selecting a closed caption mode it will stay in effect until it is changed even if the channel is changed If the captions signal is lost due to a commercial or a break in the signal the captions will reappear when the signal is received again If the channels are changed the captions will be delayed approximately 10 seconds The captions will appear in places on the screen where they will least interfere with the picture usually on the bottom of the screen News programs will usually show three line closed captions which scroll onto the screen Most ot
26. CTION 810 20 ELECTRIC SERVICE EQUIPMENT lt GROUNDING CONDUCTORS NEC SECTION 810 21 GROUND CLAMPS NEC NATIONAL ELECTRICAL CODE POWER SERVICE GROUNDING ELECTRODE SYSTEM 52898 250 IMPORTANT RECYCLING INFORMATION This product uses both Cathode Ray Tube CRT and other components that contain lead In your community there might be regulations that require you to dispose these materials properly under environmental considerations Please contact your local authorities or the Electronic Industries Alliance http www eiae org for disposal or recycling information 5L80101C 01 09 3 20 4 04 16 19 LE FEATURES Color TV With Video Cassette Recorder Unique space saving design combines a color TV and a video cassette recorder High Quality Picture Technology This TV VCR equipped incorporates VHS High Quality technology A built in detail enhancer is used to boost the recorded signal and provide picture quality during playback It is compatible with other VHS video cassette recorders 181 Channel Tuner Receives standard VHF and UHF broadcast channels and up to 113 cable channels The actual number of channels received depends upon channel reception in your area or your cable system Closed Caption Decoder With Full Text Mode Displays text captions or full screen text on the screen for hearing impaired viewers 8 Pro
27. D DELETE then press SI el fl Go TVICABLE CABLE TVICABLE CABLE AUTO CH MEMORY AUTO CH MEMORY ADD DELETE gt ADD DELETE AI VIALE MENU MENU Select the desired channel Press 4 or to select ADD Press MENU repeatedly to be memorized or deleted or DELETE If you select an until the menu screen is using A or V Direct unmemorized channel the cleared channel selection 0 9 channel indication will be red If you select ADD the channel indication changes from red to green and the channel will be memorized If you select a memorized channel the channel indication will be green If you select DELETE the channel indication changes from green to red and the channel will be deleted from the memory 0 9 A VI 4 b MENU 5L80101C P20 33 24 20 4 04 16 20 SETTING THE V CHIP An age limitation can be set to forbid children to watch programs according to TV RATING and MOVIE RATING level set To use the V Chip function you must register a password TO REGISTER PASSWORD Press MENU Press lt or gt to select UT pa V CHIP SET NEW PASSWORD A 4 gt MENU Press A or V to select Enter the password 4 digits Enter the same password PASSWORD using Direct chan
28. ED CAPTION CHANNEL RETURN Press CLOSED CAPTION to switch between normal CHANNEL RETURN allows you to go back to the last TV and the two closed caption modes captions and channel selected by pressing CHANNEL RETURN full screen text Closed captioning will display text on Press this button again to return to the last channel the screen for hearing impaired viewers you were watching CHANNEL RETURN CAPTION CH1 NOTES If using an indoor antenna or if TV reception is very poor the closed caption decoder text may not appear In this case adjust the antenna for better reception or use an outdoor antenna When activating the closed captioned decoder there will be a short delay before the closed captioned text appears on the screen Closed captioned TV programs can be recorded and played back on a VCR with the closed captioned text intact The closed captioning text will disappear during cue rewind and pause modes or if the VCR tracking is not adjusted properly 20 Closed captioned text is only displayed in locations where it is available e If the call display is on the closed captioning text will not appear 5L80101C P20 33 20 20 4 04 16 20 WHAT IS CLOSED CAPTIONING This television has the capability to decode and display closed captioned television programs Closed captioning will display text on the screen for hearing impaired viewers or it will translate and display text in another language
29. F UHF antenna reposition or rotate antenna The CLOSED CAPTION button is not depressed Press the CLOSED CAPTION button to turn on the closed caption RECORDING TV recording does not work The video cassette s erase prevention tab is broken off Place a piece of vinyl tape over the hole Timer recording does not work The time is not set correctly Reset the present time The recording start end time is not Set correctly Reset the start end time The TIMER REC buttons has not been pressed The TIMER REC indicator is not lit Press the TIMER REC buttons The TIMER REC indicator is lit PLAYBACK Noise bars appear on the Screen Tape is old or worn Replace the tape Tracking adjustment is beyond range of automatic tracking circuit Adjust tracking manually using the TRACKING or button on the remote control Video heads are dirty Clean the video heads REMOTE CONTROL Remote control does not operate 5L80101C P44 BACK The remote control is not aimed at the sensor Aim the remote control at the remote sensor Distance is too far or too much light in the room Operate within 15 feet or reduce the light of the room There is an obstacle in the path of the beam Clear the path of the beam The batteries are weak Replace the batteries The batteries are not inserted correctly Insert correc
30. HEN YOU EXPERIENCE THE ABOVE CONDITIONS Plug the power cord into an AC outlet press the POWER button to turn on RET and leave the unit at room temperature until moisture condensation disappears Video Tape Depending on the surrounding conditions this may take about three hours Head Drum If you cause a static discharge when touching the Avoid extreme heat unit and the unit fails to function simply unplug the unit from the wall outlet wait a few minutes and plug it back in The unit should return to normal operation Do not place the unit on or near appliances which may Avoid extreme cold cause electromagnetic interference e g speakers etc Doing so may cause erratic operation of the unit including picture and or sound distortion or noise The ventilation holes prevent overheating Do not block or cover these holes Especially avoid covering the holes with soft materials such as cloth or paper 5L80101C 01 09 6 20 4 04 16 19 Do not insert fingers or any other objects into the cassette loading slot Do not spray cleaner or wax directly on the unit or use forced air to remove dust Keep the unit away from flower vases sinks etc If liquids should be spilled into the unit serious damage will result If you spill any liquids into the unit unplug the AC power cord immediately and consult qualified service personnel before attempt ing to use it again When you leave you
31. IMER REC SET AUTO REPEAT AUTO REPEAT A VI4I EI MENU AJ VIE MENU Press the A or V to select the program Press lt or gt to select the date then press position then press ENTER ENTER MENU A I4 E MENU 8 TIMER REC SER 7 DATE 23 THU START 830AMN END 012 SPEED SP NOTES If programming is performed without a tape in the TV VCR or with a tape without an erase prevention tab the timer recording is not possible If a tape without an erase prevention tab is in the TV VCR the tape will be ejected record from the external equipment press 4 or gt repeatedly until L LINE from AUDIO VIDEO IN jacks on the front appears when setting the channel in step 5 5L80101C P34 43 42 20 4 04 16 22 Set the start time end time channel and tape Press ENTER Speed as in step 4 3 62 Fia E 23 TH 7 00PM 9 80PM 07 2 AJ VI amp I EI ENTERIMENU A YI ENTER CANCEUMENU Press both TIMER REC at the same time The TIMER REC indicator will light When the programed time is reached the record ing is automatically started TIMER REC 7 6 cancel timer recording press both the buttons again and TIMER REC indicator will go off To set the timer for another program repeat Steps 3 to 6 to set the second program
32. L PICTURE SKIP SEARCH Press PAUSE STILL in the PLAY Press SKIP SEARCH in the PLAYBACK mode The TV VCR will BACK mode search forward through approximately 30 seconds of the tape e g unwanted commercial time for each press of SKIP SEARCH maxi mum six presses and then resume normal playback PAUSE STILL For example 1 press 30 seconds of tape 2 press 60 seconds of tape 3 press 90 seconds of tape Press PLAY or PAUSE STILL to resume normal playback NOTES Best results during speed search and still playback can be obtained with video cassettes recorded in the SLP mode The audio output is muted during speed search and still A few noise bars will appear on the TV screen during speed search and still To prevent damage to the tape still and speed search mode is automatically changed to the playback mode after 5 minutes 7 5L80101C P34 43 37 20 4 04 16 22 SPECIAL PLAYBACK CONTINUED TO WATCH A TAPE REPEATEDLY Press MENU Press A or V to select AUTO REPEAT Press 4 or to select 22 option o ES Dal E Fj E TIMER REC SET TIMER REC SET AUTO REPEAT AUTO REPEAT AIVI4I E MENU AI VIALE MENU Press 4 or gt to select ON Press MENU repeatedly until menu screen is cleared If you press PLAY the tape will play over and over until the repeat mode is canceled
33. ND VIDEO CASSETTE RECORDER Toshiba America Consumer Products L L C TACP makes the following limited warranties These limited warran ties extend to the original consumer purchaser or any person receiving this set as a gift from the original consumer purchaser and to no other purchaser or transferee Limited Ninety 90 Day Warranty TACP warrants this product and its parts against defects in materials or workmanship for a period of ninety 90 days after the date of original retail purchase During this period TACP will repair a defective product or part without charge to you You must deliver the entire set to an Authorized TACP Service Station You pay for all transportation and insurance charges for the set to and from the Service Station Limited One 1 Year Warranty TACP further warrants the parts in this product against defects in materials or workmanship for a period of one year after the date of original retail purchase During this period TACP will replace a defective part without charge to you except that if a defective part is replaced after ninety 90 days from the date of original retail purchase you pay labor charges involved in the replacement You must also deliver the entire product to a TACP Authorized Service Station You are responsible for all transportation for the set to and from the Service Station Limited Two 2 Year Warranty of Picture Tube TACP further warrants the picture tube in this product against defects
34. NG RECORDING A TV PROGRAM ONE TOUCH TIMER RECORDING OTR TIMER BEGORBDING ctt tete m P OTHER FUNCTIONS FOR THE TIMER RECORDING ssssssssseseesneeeenetnenetetnetnenetnetneetnetretn treten ea ADDITIONAL INFORMATION USING THE REAL TIMETAPEGCOBUNTER 2 nece corte tette it ti e e osa eren cet rere rip ertet USING ZERO BETUFRN icr tete ce cert ete ete ee E VIDEO INDEX SEARCH SYSTEM TO MONITOR A TV PROGRAM 2 47 DUPLIGATING A VIDEO TABE ett rct 48 RECEPTION DISTURBANCES 49 PROBLEM AND TROUBLESHOOTING GUIDE 50 VIDEO HEAD 52 ize ues 52 BI spe DCUM 53 5L80101C 01 09 5 20 4 04 16 19 SAFETY PRECAUTIONS MOISTURE CONDENSATION DO NOT OPERATE ANY FUNCTIONS ON THIS UNIT FOR AT LEAST THREE HOURS WHEN MOISTURE IN THE AIR CONDENSES ON IT LET THE UNIT STAND WITH POWER ON SEE BELOW W WHAT IS MOISTURE CONDENSATION When a cold liquid is poured into a glass for example water vapor in the air will condense on the surface of the glass This is called moisture condensation MOISTURE WILL CONDENSE ON THE UNIT IN THE FOLLOWING CASES When you move the unit from a cold to a warm place After heating a cold room or under extremely humid conditions C E W
35. OL FRANCAIS ENTER MENU 5L80101C P10 19 14 20 4 04 16 19 AUTO CLOCK SETTING The auto clock function will automatically set the built in clock Month Day Year and Time when the TV VCR is connected to an antenna or cable TV system and it is turned off As the TV VCR searches for a receivable station in your area and it receives a broadcast signal for auto clock the auto clock needs several minutes to set itself AUTO CLOCK SETTING Connect the antenna or cable TV system f you use a cable box turn it on Plug the AC power cord to the AC outlet Make sure the TV VCR is turned off f you press POWER the auto clock set is not effective Wait at least three minutes and press POWER Press CALL to check the clock on the screen If the clock is not set check the antenna condition The auto clock may not function properly if the reception condition is not good AUTO CLOCK ADJUSTMENT The auto clock adjustment will be performed at 12 00 PM everyday if you turn off the TV VCR If you use a cable box and you want auto clock adjustment to be performed the cable box must be left on The auto clock adjustment is not effective when there is a difference of more than 5 minutes exists between the built in clock time and the actual time TO SET AUTO CLOCK TO OFF When shipped from factory the AUTO CLOCK option is set to ON But if you do not want Auto Clock set
36. SS avor f CONTRAST 32 COLOR A v TNT o 4 ont SHARPNESS 0 DOES iA V t AJ V 4 b CANCEL MENU Selection 4 Pressing gt BRIGHTNESS darker lighter CONTRAST lower higher COLOR paler deeper TINT reddish greenish SHARPNESS softer sharper NOTE To reset the picture adjustments to the factory settings press CANCEL in the PICTURE menu All settings reset to the factory settings 5L80101C P20 33 31 20 4 04 16 21 a CADJUSTING THE PICTURE PREFERENCE You can select four picture modes Sports Standard Movie and Memory as described in the following table Press MENU Press A or V to select PICTURE Press 4 or P to select 4 option PREFERENCE then press P LANGUAGE LANGUAGE IDIOMALLANGUE gt IDIOMALANGUE gt PICTURE PICTURE gt PICTURE PREFERENCE gt PICTURE PREFERENCE gt AI VII IMENU AI VIE MENU Press A or V to select the desired picture Press MENU repeatedly until the menu mode then press ENTER Screen is cleared ETETETEE PICTURE PREFERENCE ANDARD AL V ENTER MENU Mode Picture Quality STANDARD Standard picture quality factory set SPORTS Bright and dynamic picture factory set MOVIE Movie like picture setting factory set MEMORY Your
37. T button Press to eject the tape POWER button Press to turn the TV VCR on Press again to turn the TV VCR off TV MONITOR button Used to temporarily view a TV channel selected on the VCR while in the playback mode SLEEP button Sets the TV to turn off automatically after up to 120 minutes CANCEL button Used to clear the selected program or the input data MUTE button Press to turn off the sound Press again to turn the sound back on CHANNEL and A V cursor buttons CHANNEL Press the button to change to a higher numbered channel set into memory Press the button to change to a lower numbered channel set into memory A cursor Selects an item in the menu PAUSE STILL button During recording this button temporarily stops the tape During playback it stops the tape and displays a still image on the TV screen FF Fast Forward button In the Stop mode this button rapidly winds the tape forward In the Play mode this button activates forward search 16 17 18 20 21 22 23 24 25 26 27 28 29 INPUT SELECT button Switches the program for viewing between the TV VCR and external input sources SPEED button Sets the tape speed for recording REC and TIMER REC buttons REC Press both buttons at the same time once to start normal recording Additional presses activate One touch Timer Recording TIMER REC Used to set the TV VCR to start
38. TE The V Chip function is activated only on programs and tapes that have the rating signal 5L80101C P20 33 26 20 4 04 16 21 Press lt or to select desired rating then press MENU to return to V CHIP menu screen OFF MOVIE RATING is not set G All ages PG Parental guidance PG 13 Parental guidance less than 13 years old Under 17 years old Parental guidance suggested V TV RATING v 17 years old and above Adult only RATING 13 A 4 gt ENTERIMENU Press A or V to select Press MENU repeatedly V CHIP 1 until the menu screen is cleared V CHIP V CHIP gt ON V CHIP SET gt V CHIP SET gt CHANGE PASSWORD CHANGE PASSWORD gt a 4 gt MENU a 4 gt MENU To use the TV after the TV is protected When the program applied to the V Chip setting is received enter the password then press ENTER When the password is entered correctly the protection will be temporarily overridden 5L80101C P20 33 27 20 4 04 16 21 SETTING THE V CHIP CONTINUED TO CHANGE PASSWORD Press MENU Press 4 or gt to selec option SET PASSWORD a 4 gt MENU Press A or V to select PASSWORD V CHIP SET NS 4 hj
39. TION COPYRIGHT WARNING 5L80101C COV IN This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Federal Communications Commission Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the distance between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by the party responsible for compliance with the FCC Federal Communications Commission Rules could void the user s authority to operate this equipment It is permissible to record television programs films video tapes and other material only in the event that thi
40. W or FF mode DIGITAL TRACKING CONTROLS When a tape is played the digital auto tracking system automatically adjusts the tracking to obtain the best possible picture If noise bars appear during playback adjust the tracking manually as follows Press TRACKING or to obtain the best possible picture MANUAL TRACK will appear for 4 seconds on the screen To resume automatic tracking press DIGITAL TRACKING DIGITAL TRACK will appear for 4 seconds on the screen TRACKING DIGITAL TRACKING FHA MANUAL TRACK 44 DIGITAL TRACK 1 5L80101C P34 43 36 20 4 04 16 22 LE SPECIAL PLAYBACK TO VISUALLY SEARCH FOR DESIRED POINTS When either FF or REW is pressed in the PLAYBACK mode the speed search picture will appear When pressed twice the search picture will increase speed Speed search time depends upon the speed used SP or SLP during recording See chart below To rewind or fast forward a tape press STOP and then press REW or FF To visually search backward press REW once or twice To visually search forward press FF once or twice in in the PLAYBACK mode the PLAYBACK mode FF 3 Press PLAY to resume normal viewing speed Press PLAY to resume normal viewing speed SPEED SEARCH TIMES PICTURE SEARCH SPEED PRESS PRESS ONCE TWICE TAPE SPEED SP Standard Play 3X 5X SLP Super Long 9x 15X Play SKIP SEARCH REW STOP TO WATCH STIL
41. corder CONNECTION TO ANOTHER VCR CONNECTION TO CAMCORDER For duplicating a previously recorded tape from a camcorder follow the camcorder manufacturer s instructions A typical Recording TV VCR camcorder dubbing hookup is shown below Recording TV VCR Playback Camcorder Playback VOR To AV jack dm To VIDEO To AUDIO OUT OUT To Video In To Audio In To Video Audio In Audio Video cable not supplied Audio Video cable not supplied Press both REC at the same Press PLAY on the playback Press STOP after duplicating time on the remote control of VCR or Camcorder a video tape the TV VCR D NOTES Itis recommended that the tape speed be set to the SP mode on the TV VCR for best result e Unauthorized recording of copyrighted television programs films video cassettes and other materials may infringe the rights of copyright owners and be contrary to copyright laws 48 5L80101C P44 BACK 48 20 4 04 16 23 HENENSSS 2 ZT RECEPTION DISTURBANCES Most types of television interference can be remedied by adjusting the height and position of the VHF UHF antenna Outdoor antennas are recommended for best results The most common types of television interfer ence are shown below If one of these symptoms appear when the TV VCR is connected to a Cable TV system the disturbance may be caused by the local Cable TV company broadcast IGNITION Black spots or
42. e When you load a tape the counter will reset to 00 00 00 The counter does not function on nonrecorded blank sections of the tape When you rewind fast forward or play tapes through blank sections the counter stops 5L80101C P44 BACK 45 20 4 04 16 23 l USING ZERO RETURN The zero return function provides a convenient method of rapidly returning to the starting point of recording or playback The starting point can be indexed for any location on the tape by pressing COUNTER RESET and ZERO RETURN Press CALL Before playback or recording press COUNTER RESET to set the counter to 00 00 00 COUNTER RESET 8 40AM THU CH 012 8 40AM THU CH 012 00 30 50 SP 00 00 00 SP Begin playback or recording Press STOP Press ZERO RETURN The tape will rewind and automatically stop at the 00 00 00 position ZERO RETURN 9 00AM THU CH012 9 00AM THU 00 00 00 SP 46 5L80101C P44 BACK 46 20 4 04 16 23 LE INDEX SEARCH SYSTEM TO MONITOR TV PROGRAM Video index search system This function enables you to locate the beginning of any recording made on the VCR Recording an INDEX mark Index search The index search function automatically records an Press INDEX or during stop or play mode INDEX mark on the tape whenever a recording is For succeeding programs Press INDEX initiated For preceding programs Press INDEX
43. ead the rating of a TV program or movie content if the program is encoded with this information V Chip will allow you to set a restriction level TV Monitor When the TV MONITOR button on the remote control is pressed during playback the TV channel selected on the TV VCR can be viewed 5L80101C P01 09 4 20 4 04 16 19 TABLE OF CONTENTS Please read the descriptions and operating procedures contained in this Owner s Manual prior to operating your new TV VCR o 0000000068 PREPARATION SAFETY PRECAUTIONS onde the cie notte debes dite ctp Lee LOCATION OF CONTROLS REMOTE CONTRO bits ANTENNA CONNECTIONS CABLE TV CONNECTIONS STARTING SETUP SETTING THE LANGUAGE AUTO CLOCK SETTING MANUAL CLOCK SETTING TV OPERATION e IEVCORERATION TO MEMORIZE CHANNELS X SETTING THE V CHIP 25129 TO SET THE ON TIMER 2229 TO SET THEOFF TIMER ne 30 PICTURE CONTROL ADJUSTMENTS ADJUSTING THE PICTURE PREFERENDGE ntis tinta netta tr tuat e terae ta AEA Da SE aia SHER PLAYBACK LOADING AND UNEOADING A VIDEO CASSETTE ettet etit tette nett tete e Ee a teat ku ata unas PLAY BAGK 38 SPECIAL PEAY ec RECORDI
44. gain to recorded Example Channel 12 stop recording after 30 minutes Each additional press of both REC will increase recording time as shown below up to a maximum of 6 hours OTR will appear on the screen TV VHF UHF channels CABLE Cable TV channels OTR 0 30 CH 012 NOTES Press both REC at the same time to increase the time needed for recording see the chart below Press once twice times 4times 5times 6times 7 times 8times 9 times 10 times Recording time NORMAL REC 0 30 1 00 1 30 2 00 3 00 4 00 5 00 6 00 NORMAL REC To cancel OTR press STOP The TV VCR channel cannot be changed during recording 41 5L80101C P34 43 41 20 4 04 16 22 RECORDING Timer recording can be programmed on screen with the remote control The built in timer allows automatic unattended recording of up to 8 programs within 1 month EXAMPLE Program a timer recording for 23rd day channel 007 CABLE 7 00 9 30 PM Tape speed SLP Load a video cassette with the erase prevention tab intact The TV VCR will automatically turn on Set the TV CABLE selection to the appropriate position see page 22 Press MENU Press A or V to select TIMER REC SET Press lt or gt to select amp option then press gt EE E TIMER REC SET T
45. ghts which may vary from state to state Some states do not allow limitation on how long an implied warranty lasts when an action may be brought or the exclusion or limitation of incidental or consequential damages so the above provisions may not apply to you ATTENTION CANADIAN CONSUMERS Canadian consumers are requested to complete the special Canadian Warranty Registration Form enclosed and forward this completed form with a copy of bill of sale to TOSHIBA OF CANADA to Register and Validate their warranty Products purchased in the U S A and used in Canada are not covered by these warranties Products purchased in Canada and used in the U S A are not covered by these warranties Rev 09 01 98 TOSHIBA AMERICA CONSUMER PRODUCTS L L C JSL80101C 04 04 U PRINTED IN THAILAND 5L80101C P44 BACK 54 20 4 04 16 23
46. grams 1 Month Programmable Timer With Everyday Every Week Capability The built in timer allows automatic absentee recording of up to 8 TV programs within 1 month It is also possible to record a program which is broadcast at the same time everyday or every week Starting Setup It leads you the Language selection TV CABLE selection Auto channel memory and Auto clock setting automatically Automatic Clock Set Once your TV VCR is plugged into the AC outlet it automatically sets the correct date and time On Screen TV Display And VCR Programming When you select a channel or make other changes the TV will show an indicator on the screen for a few seconds Timer recording can be programmed and confirmed on the screen Picture Adjustments Using The Remote Control The On Screen display allows remote control adjustment of BRIGHT NESS CONTRAST COLOR TINT and SHARPNESS Picture Preference You can select four picture modes Sports Standard Movie and Memory Automatic Playback Rewind Stop Eject When loading a cassette tape without the erase prevention tab this TV VCR will automatically play back the cassette tape at the correct speed When a tape reaches its end during play back recording except during OTR and Timer Record and fast forward it will automatically stop rewind stop and eject the tape Programmable ON OFF Timer Allows you to automatically turn on or off the TV VCR at a set time Programmable TV Sleep Timer Operab
47. he TV CABLE option is in the TV position all channels can be instantly selected by using two buttons for example to select channel 2 press 0 then 2 If you press only 2 channel selection will be delayed for a few seconds For channels 10 and above press the 2 digits in order CABLE mode direct channel selection When the TV CABLE option is in the CABLE position channels can be selected as follows TO SELECT CABLE CHANNELS 1 9 Press 0 twice then 1 9 as needed Example to select channel 2 press 002 10 12 Press 0 then the remaining 2 digits Example to select channel 12 press 012 13 99 Press the 2 digits in order Example to select channel 36 press 36 100 125 Press the 3 digits in order Example to select channel 120 press 120 gt gt NOTE FOR CHANNELS 1 12 If only 1 or 2 buttons are pressed the corresponding channel will be selected in 2 seconds NOTES If a channel with no broadcast is selected the sound will automatically be muted e If a station being viewed stops broadcasting the TV will automatically shut itself off after 15 minutes 5L80101C P10 19 18 20 4 04 16 20 CHANNEL Press and release CH or The channel automati cally stops at the next channel set into memory For proper operation before selecting channels they should be set into the memory See pages 23 and 24 To memorize channels MUTE Press MUTE to switch off the sound The TV VCR s sound wi
48. he menu screen is cleared MENU SH gt ONTIMER 12 00AM CH001 SUN gt 11 30PM A V 4I ENTER MENU NOTES If a station being viewed stops broadcasting the TV will automatically shut itself off after 15 minutes cancel OFF TIMER follow above steps 1 5 then press lt or to select CANCEL Press MENU repeatedly until the menu screen is cleared To confirm the ON OFF TIMER Press PROGRAM twice to indicate the programs on the screen 30 30 20 4 04 16 21 1 13 BJCTURE CONTROL ADJUSTMENTS You can adjust the picture quality to your personal preferences including the contrast brightness color tint and sharpness The qualities you choose will be stored automatically in your TV s memory so you can recall them at any time Press MENU Press A or V to select PICTURE then Press 4 or gt to select option press E L h E E E 1M E LANGUAGE LANGUAGE IDIOMALANGUE PICTURE PICTURE PICTURE PREFERENCE PICTURE PREFERENCE gt AL V 4I EI MENU A VIE MENU Press A or V until the item you want to adjust Press MENU repeatedly until the menu screen is highlighted then press 4 or gt to adjust the is cleared level BRIGHTNE
49. her shows provide two or three lined captions placed near the character who is speaking so the viewer can follow the dialogue Words in italics or underlined describe titles words in foreign languages or words requiring emphasis Words that are sung usually appear enclosed by musical notes For television programs broadcasting with closed cap tions look in your TV guide for the closed captions symbol CC When selecting closed captions the captioning will be delayed approximately 10 seconds If no caption signal is received no captions will appear but the television will remain in the caption mode Misspellings or unusual characters may occasionally appear during closed captioning This is normal with closed captioning especially with live programs This is because during live programs captions are also entered live These transmissions do not allow time for editing When captions are being displayed on screen displays such as volume and mute may not be seen or may interfere with closed captions Some cable systems and copy protection systems may interfere with the closed captioned signal If using an indoor antenna or if TV reception is very poor the closed caption decoder may not appear or may appear with strange characters or misspelled words In this case adjust the antenna for better reception or use an outdoor antenna 5L80101C P20 33 21 21 20 4 04 16 20 ZZ o on MEMORIZE CHANNELS
50. horizontal streaks may appear the picture may flutter or drift Usually caused by interference from automobile ignition systems neon lamps or AC powered tools and appliances such as drills or hair dryers GHOSTS Ghosts are caused by the television signal following two paths One is the direct path and the other is reflected by tall buildings hills or other large objects Changing the direction or position of the antenna may improve the reception SNOW If the TV VCR is located far from the TV station in a fringe reception area where the signal is weak small dots may appear in the picture If the signal is extremely weak the installation of a larger external antenna may be necessary RADIO FREQUENCY INTERFERENCE RFI Caused by two way radios this type of interference produces moving ripples or diagonal streaks in the picture Some cases may cause a loss of contrast in the picture Changing the direction and position of the antenna or installing an RFI filter may improve the picture PICTURE SIZE VARIATION A slight picture size variation is normal when you adjust the CONTRAST or BRIGHTNESS settings CARE AND MAINTENANCE To prevent fire or shock hazard disconnect the TV VCR from the AC power sources before cleaning The finish on the cabinet may be cleaned with mild soap and a soft damp cloth and cared for as other furniture Use caution when cleaning or wiping the plastic parts 5L80101C P44 BACK 49 20 4 04 16 23
51. in materials or workmanship for a period of two 2 years after the date of original retail purchase During this period TACP will replace a defective picture tube without charge to you except that if a defective picture tube is replaced after ninety 90 days from the date of the original retail purchase you pay labor charges involved in the replacement You are responsible for all charges involved in the replacement You are responsible for all transportation and insurance charges for the set to and from the Service Station Rental Units The warranty for rental units begins with the first rental or thirty 30 days from the date of shipment to the rental firm whichever comes first Commercial Units Products sold and used for commercial use have a limited ninety 90 day warranty for all parts labor and picture tube Owner s Manual and Demographic Card You should read this owner s manual thoroughly before operating this product You should complete and mail the enclosed Demographic card within ten days after you or the person who has given you this product as a gift purchased this product This is one way to enable TACP to provide you with better customer service and improved products Failure to return the Demographic card will not affect your rights under this warranty Your Responsibility The above warranties are subject to the following conditions 1 You must retain your bill of sale or provide other proof of purchase 2 All warra
52. le from the remote control the TV can be programmed up to 120 minutes to turn off automatically Automatic Repeat Play System When Auto Repeat option is turned on the TV VCR will automatically play back the same cassette tape repeatedly One touch Timer Recording OTR Simply by pressing the REC buttons the TV VCR can be programmed for up to 6 hours of recording with an immediate start Front Audio Video Input Jacks Input jacks for other video device or playback purpose Skip Search When the SKIP SEARCH button on the remote control is pressed during playback the TV VCR will auto matically search forward in 30 second increments to a maximum of 3 minutes with each press of the SKIP SEARCH button and then return to normal playback Index Search Enables you to locate the beginning of any recording made on the VCR 2 Speed Picture Search 3 or 5 times normal speed in SP mode 9X or 15X in SLP 2 Speed Record Playback Records and plays two tape speeds SP SLP Real Time Tape Counter With Zero Return The counter displays the real tape time and the zero return can be used to return the tape to a preselected position 00 00 00 while the counter can be used to locate programs Digital Auto Tracking Automatically adjusts tracking during playback for the best possible picture On Screen 3 Language Display You can select one of 3 languages English Spanish or French for on screen programming V Chip The V Chip function can r
53. ll be silenced and MUTE will briefly appear on the screen The sound can be switched back on by press ing this button again or one of the VOL MUTE Press CALL The clock date channel number real time tape counter tape speed and VCR operation will be indicated Press CALL again to disappear the call display Current time VCR operation VCR operation Play Rewind Fast forward 8 47AM THU CH ot Channel Eject Recording Recording Pause Stop Tape speed Zero return Rewind Auto repeat e 00 04 38 SP Real time tape counter Tape In Zero return Fast forward NOTE To listen through the headphone insert a headphone not supplied with a 1 8 mini plug into PHONE jack on the front The sound from the TV speaker is muted 5L80101C P10 19 19 19 20 4 04 16 20 LE OPERATION CONTINUED SLEEP To set the TV VCR to turn off after a preset amount of time press SLEEP on the remote control The clock will count down 10 minutes for each press SLEEP 120 110 10 0 After the sleep time is programmed the display will appear briefly every ten minutes to remind you that the sleep timer is operating To confirm the Sleep timer setting press SLEEP and the remaining time will be displayed for a few seconds To cancel the sleep timer press SLEEP repeatedly until the display turns to 0 CLOSED CAPTION CHANNEL RETURN SLEEP CLOS
54. nel again for safety then press selection 0 9 then press ENTER ENTER T Dal m V CHIP SET cobi NEW CONFIRM V CHIP SET PASSWORD PASSWORD NEW NIZ PASSWORD 2 CN 0 9 ENTER CANCELIMENU 0 9 ENTER CANCEL IMENU See ere x appears instead of the number V CHIP SET menu appears 5L80101C P20 33 25 20 4 04 16 20 SETTING THE V CHIP CONTINUED TO SET THE V CHIP In the V CHIP menu press A or V to select V Press A or V to select TV RATING then CHIP SET then press press lt or gt to display the desired setting V CHIP V CHIP SET V CHIP SET gt TV RATING CHANGE PASSWORD MOVIE RATING A 4 gt ENTERMENU OFF TV RATING is not set Allchildren TV Y7 7 years old and above TV G General Audience TV PG Parental guidance TV 14 14 years old and above TV MA 17 years old and above When you select TV Y7 TV PG TV 14 or TV MA press von ser CALL to explain the rating Press or V to select the MOVIE RATING desired rating you want Press 4 or to select the set ting ON or OFF A VI4IF ENTERMENU m NO
55. nty servicing of this product must be made by an Authorized TACP Service Station 3 These warranties are effective only if the product is purchased and operated in the U S A or Puerto Rico 4 Labor service charges for set installation set up adjustment of customer controls and installation or repair of antenna systems are not covered by this warranty Reception problems caused by inadequate antenna sys tems are your responsibility Warranties extend only to defects in materials or workmanship as limited above and do not extend to any product or parts which have been lost or discarded by you or to damage to products or parts caused by misuse accident damage caused by Acts of God such as lightning or fluctuations in electric power improper installa tion improper maintenance or use in violation of instructions furnished by us or to units which have been altered or modified without authorization of TACP 5 53 5L80101C P44 BACK 53 20 4 04 16 23 How to Obtain Warranty Service If after following all of the operating instructions in this manual and checking the section Problems and troubleshooting and you still find that service is needed 1 Call the TACP toll free number 1 800 631 3811 after you find a defective product or part to find the nearest Toshiba Authorized Service Station 2 Please present your bill of sale or other proof to the Authorized Service Station TACP Authorized Service Station personnel will come to your
56. r home for a long time unplug the AC power cord POWER SOURCE TO USE AC POWER Use the AC polarized line cord provided for operation on AC Insert the AC cord plug into a standard 120V 60Hz polarized AC outlet NOTES Never connect the AC line cord plug to anything other than the specified voltage 120V 60Hz Use the attached power cord only If the polarized AC cord does not fit into a nonpolarized AC outlet do not attempt to file or cut the blade It is the user s responsibility to have an electrician replace the obsolete outlet If you cause a static discharge when touching the unit and the unit fails to function simply unplug the unit from the AC outlet wait a few minutes and plug it back in The unit should return to normal operation seconds before pressing the POWER button 5L80101C 01 09 7 If the AC cord plug is plugged in for the first time wait for about 5 Avoid places subject to strong vibration Use in a horizontal flat position only When you finish operating the unit always unload the cassette and turn off the power To protect the unit from a lightning storm unplug the AC power cord from the wall outlet and disconnect the antenna Wider Hole AC Outlet and Blade Polarized AC Cord Plug One blade is wider than the other 7 20 4 04 16 19 e M DDCATION OF CONTROLS FRONT
57. rd party copyrights and other rights are not violated Unauthorized recording of copyrighted television programs films video cassettes and other materials may infringe the rights of copyright owners and be contrary to copyright laws 2 20 4 04 16 18 a fos IMPORTANT SAFEGUARDS 1 READ INSTRUCTIONS All the safety and operating instructions should be read before the unit is operated 2 RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference 3 HEED WARNINGS All warnings on the unit and in the operating instructions should be adhered to 4 FOLLOW INSTRUCTIONS All operating and use instructions should be followed 5 CLEANING Unplug this unit from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning the exterior cabinet only 6 ATTACHMENTS The manufacturer of this unit does not make any recommendations for attachments as they may cause haz ards 7 WATER AND MOISTURE Do not use this unit near water For example near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool PORTABLE CART WARNING 8 ACCESSORIES symbol provided by RETAC Do not place this unit on an unstable cart stand tripod bracket or table The unit may fall causing serious injury and serious damage to the unit 8A An appliance and cart combination should be moved with care Quick stops excessive force and
58. recording at a preset time VOLUME lt gt cursor buttons VOLUME Press the button to increase or the button to decrease the volume level lt gt cursor Select an item or adjust the setting in the menu INDEX buttons Search for the INDEX mark of a tape REW Rewind button In the Stop mode this button rapidly winds the tape backwards In the Play mode this button activates reverse search SKIP SEARCH button Press in the playback mode to search forward in 30 second increments to a maximum of 3 minutes COUNTER RESET button Used to reset the counter to 00 00 00 CHANNEL RETURN button Switches between the present channel and the last channel selected ZERO RETURN button Use to stop the tape when the counter reaches 00 00 00 ENTER button Press to enter or select information for on screen operations TRACKING buttons During playback they are used to adjust tracking manually PLAY button Press to play a prerecorded tape STOP button Press once to stop the tape 9 20 4 04 16 19 REMOTE CONTROL CONTINUED BATTERY INSTALLATION Slide the battery compart Install two AAA batteries Replace the compartment ment cover in the direction paying attention to the of the arrow polarity diagram in the battery compartment BATTERY PRECAUTIONS The precautions below should be followed when using bat
59. stment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation e If the unit has been dropped or the cabinet has been damaged f When the unit exhibits a distinct change in performance this indicates a need for service 19 REPLACEMENT PARTS When replacement parts are required be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 5L80101C P01 09 2 20 4 04 16 18 20 SAFETY CHECK Upon completion of any service or repairs to this unit ask the service technician to perform safety checks to determine that the unit is in proper operating condition 21 HEAT The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat 22 NOTE TO CABLE TV SYSTEM INSTALLER This reminder is provided to call the Cable TV system installer s attention to Article 820 40 of the NEC that provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE GROUND CLAMP ANTENNA DISCHARGE UNIT NEC SE
60. teries in this device Use only the size and type of batteries specified Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment Reversed batteries may cause damage to the device Do not mix different types of batteries together e g Alkaline and Carbon zinc or old batteries with fresh ones If the device is not to be used for a long period of time remove the batteries to prevent damage or injury from possible battery leakage Do not try to recharge batteries not intended to be recharged they can overheat and rupture Follow battery manufacturer s directions EFFECTIVE DISTANCE OF THE REMOTE CONTROL NOTES When there is an obstacle between the TV VCR and the remote control the remote control may not operate e When direct sunlight an incandescent lamp fluorescent lamp or any other strong light shines on the Remote sensor of the TV VCR the remote operation may be unstable e When using the remote control press the button at intervals of about 1 second to ensure the correct mode of operation 5L80101C P10 19 10 20 4 04 16 19 CANTENNA CONNECTIONS If you are using an indoor or outdoor antenna follow the instructions below that correspond to your antenna system If you are using a cable TV service CABLE see page 12 for Cable TV connections Combination VHF UHF antenna Single 75 ohm cable or 300 ohm twin lead wire
61. then conflicting programs will be lost The first press gt Press or V to select the unnecessary recording time has priority over the next program and press CANCEL to cancel the program recording time as shown in the diagram CANCEL 10 00 Program 1 Progam2 gt Progam3 Non Recorded Portion Parts Recording Prog 2 Control Settings A V NOTES The everyday every week recording can be made continuously until the recording is canceled or the tape reaches the end During timer recording the automatic rewinding mechanism does not function e You can correct or cancel the programmed setting in program confirm mode 44 5L80101C P44 BACK 44 20 4 04 16 23 sinc THE REAL TIME TAPE COUNTER The on screen real time tape counter shows the tape running time in hours minutes and seconds You can easily determine how long the tape has been running or how much time is left on the tape TO VIEW THE COUNTER DISPLAY Press CALL Press COUNTER RESET to set the counter to 00 00 00 COUNTER RESET 8 40AM THU CHO12 8 40AM THU CH 012 a 00 30 50 SP 00 00 00 SP When you wish to make the counter disappear Begin playback or recording the counter will display the elapsed time press CALL again NOTES If you rewind the tape from 00 00 00 a minus sign will be displayed in front of the tim
62. tlets and extension cords as this can result in a risk of fire or electric shock 16 OBJECT AND LIQUID ENTRY Do not push objects through any openings in this unit as they may touch dangerous voltage points or short out parts that could result in fire or electric shock Never spill or spray any type of liquid into the unit 17 OUTDOOR ANTENNA GROUNDING If an outside antenna or cable system is connected to the unit be sure the antenna or cable system is grounded to provide some protection against voltage surges and built up static charges Section 810 of the National Electrical Code NEC ANSI NFPA 70 provides information with respect to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode 18 SERVICING Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel For example a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the unit c If the unit has been exposed to rain or water d If the unit does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adju
63. tly 20 4 04 16 23 51 eT eee DEO HEAD CLEANING VIDEO HEAD CLOGGING The video heads are the means by which the TV VCR reads the picture from the tape during playback In the unlikely event that the heads become dirty enough to be clogged no picture will be played back This can easily be deter mined if during playback of a known good tape there is good sound but no picture picture is extremely snowy If this is the case use a high quality head dn cleaning system or have them cleaned professionally EG aaa t 4 MY VIDEO HEAD CLEANING Good picture Snowy picture Video head cleaning is needed when the playback picture becomes unclear This signifies that the heads are getting dirty and can occur when playing poor quality or damaged tapes If the heads require cleaning use a equivalent high quality chemical non abrasive wet head cleaning tape or have them cleaned professionally If playing a head cleaning tape in the VCR once does not improve the picture play it several times before requesting service DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR SERVICE THE UNIT BY REMOVING THE TOP COVER NOTES Video heads may eventually wear out and should be replaced when they fail to produce clear pictures To help prevent video head clogging use only good quality VHS tapes Discard worn out tapes SPECIFICATIONS TELEVISION Picture tube Type 13 335 4 mm diagonal Tuner type Quartz PLL frequency synthesized Receiving
64. uneven surfaces may cause the appliance and cart combination to overturn 9 VENTILATION 53126 Slots and openings in the cabinet back or bottom provided for ventilation and to ensure reliable operation of the unit and to protect it from overheating These openings must not be blocked or covered The openings should never be blocked by placing the unit on a bed sofa rug or other similar surface This unit should never be placed near or over a radiator or heat source This unit should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to 10 POWER SOURCE This unit should be operated only from the type of power source indicated on the rating plate If you are not sure of the type of power supply to your home consult your appliance dealer or local power company For units intended to operate from battery power or other sources refer to the respective pages on this Owner s Manual for their operating instructions 11 GROUNDING OR POLARIZATION This unit is equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Instead of the polarized
65. ver the tape Be careful the tape does not extend past the edges of the video cassette housing Screwdriver Erase prevention tab Adhesive tape TAPE SPEED AND MAXIMUM PLAYBACK RECORDING TIME VIDEO CASSETTE TAPE TAPE SPEED T 160 T 120 T 90 T 30 SP Standard Play 2 2 3 hours 2 hours 1 1 2 hours 30 minutes SLP Super Long Play 8 hours 6 hours 4 1 2 hours 1 1 2 hours 5L80101C P34 43 34 20 4 04 16 22 PLAYBACK To play a prerecorded tape TO START PLAYBACK To turn on the TV VCR press POWER Load a prerecorded tape When loading a cassette tape without the erase prevention tab playback will start automatically TO STOP PLAYBACK Press STOP once The tape will stop but remain fully loaded and ready to play will appear on the screen Press PLAY to begin playback yp will appear on the screen NOTE This TV VCR selects the playback tape speed SP or SLP automatically 5L80101C P34 43 35 20 4 04 16 22 BLAYBACK CONTINUED TO REWIND OR FORWARD THE TAPE RAPIDLY Press REW Rewind in the stop mode Press FF Fast Forward in the stop mode 44 will appear on the screen p gt will appear on the screen E FORWARD REVERSE PICTURE SEARCH If you want to see the tape during REW or FF mode press and hold REW or FF The backward or forward visual search picture will be seen on the screen Release to return to the RE
66. y provided by the cable company FOR SUBSCRIBERS TO BASIC CABLE TV SERVICE For basic cable service not requiring a converter descrambler box connect the Cable TV 75 ohm coaxial cable directly to the antenna ANT jack on the back of the TV VCR Em gt 7 75 ohm Antenna coaxial cable jack FOR SUBSCRIBERS TO SCRAMBLED CABLE TV SERVICE If you subscribe to a cable TV service which requires the use of a converter descrambler box connect the incoming 75 ohm coaxial cable to the converter descrambler box Using another 75 ohm coaxial cable connect the output jack of the converter descrambler box to the antenna jack on the TV VCR Follow the connections shown below Set the TV VCR to the output channel of the converter descrambler box usually channel 3 or 4 and use the converter descrambler box to select channels Incoming 75 ohm 75 ohm cable to ANT Cable TV cable Converter TV VCR descrambler qm Antenna jack FOR SUBSCRIBERS TO UNSCRAMBLED BASIC CABLE TV SERVICE WITH SCRAMBLED PREMIUM CHANNELS If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the use of a converter descrambler box you may wish to use a signal splitter and an A B switch box available from the cable company or an electronics supply store Follow the connections shown below With the switch in the B position you can directly tune any nonscrambled channels on your TV VCR With the switch in the A

Toshiba MV13P2 13 in. TV/VCR Combo

Contents

Download Pdf Manuals

Related Search

Related Contents