Home
Fujitsu Siemens Celsius 670 (LKN:SWD-670115
Contents
1. Windows ME and Windows NT Task Manager appears first Then you must press all three keys again to re boot F5 CEE A26361 K670 Z100 1 7419 English 17 Preparation for Use and Operation Working with floppy disks Working with floppy disks Follow the instructions supplied by the vendor of the floppy disks Never clean the floppy disk drives with cleaning disks Any attempt would destroy the read write head in the disk drive within 20 seconds 1 Insertion direction 2 Label area 3 Write protection switch for a 720 KB or a 1 44 MB floppy disk 4 Identification of a 1 44 MB floppy disk or write protect switch on a 120 MB floppy disk 5 Eject button for inserted floppy disks 6 Disk is write protected 7 Disk is not write protected gt To insert a floppy disk push it into the drive in the insertion direction until it engages The label should be facing upward gt To remove the floppy disk press the eject button 5 The write protect switch enables you to protect the data on the floppy disk from inadvertent overwriting or deletion gt To protect the data on the floppy disk from being overwritten push the write protect switch to position 6 The hole is now visible To remove write protection push the switch to position 7 The hole is now covered 18 English A26361 K670 Z100 1 7419 Settings in BIOS Setup Preparation for Use and Operation Settings in BIOS Setup The BIOS Setup menu allows you
2. CELSIUS 670 BETRIEBSANLEITUNG OPERATING MANUAL FUJITSU COMPUTERS SIEMENS Sie haben technische Fragen oder Probleme Wenden Sie sich bitte an unsere Hotline Mo Fr 9 18 Uhr Sa 9 14Uhr Tel 49 0 180 3777 003 e Ihren zust ndigen Vertriebspartner e Ihre Verkaufsstelle Weitere Informationen finden Sie im Handbuch Sicherheit Garantie und Ergonomie Aktuelle Informationen zu unseren Produkten Tipps Updates usw finden Sie im Internet http www fujitsu siemens com Are there any technical problems or other questions you need clarified Please contact e your sales partner e your sales outlet You will find further information in the Safety Warranty and Ergonomics booklet The latest information on our products tips updates etc can be found on the Internet under http www fujitsu siemens com Dieses Handbuch wurde auf Recycling Papier gedruckt This manual has been printed on recycled paper Ce manuel est imprim sur du papier recycle Este manual ha sido impreso sobre papel reciclado Questo manuale amp stato stampato su carta da riciclaggio Denna handbok r tryckt pa recyclingpapper Dit handboek werd op recycling papier gedrukt Herausgegeben von Published by Fujitsu Siemens Computers GmbH Bestell Nr Order No A26361K670 Z100 1 7419 Printed in the Federal Republic of Germany AG 0601 06 01 A26361 K670 Z100 1 7419 CELSIUS 670 Operating Manual June
3. English A26361 K670 Z100 1 7419 Manufacturer s notes Important notes FCC Class B Compliance Statement The following statement applies to the products covered in this manual unless otherwise specified herein The statement for other products will appear in the accompanying documentation NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 ofthe FCC rules and meets all requirements of the Canadian Interference Causing Equipment Regulations These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in strict accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Roorient or relocate the receiving antenna Increase the separation between equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for hel
4. Restoring hard disk contents 23 Retransportation 6 Returnkey 17 S Safety 3 Screen blank 13 14 SCSI port 9 Security Manager 17 Security measures 19 Serial port 9 connecting devices 10 Settings BIOS Setup 19 Setup see BIOS Setup Shift key 17 SmartCard reader 9 Software installing new software 21 new installation 21 Standard keyboard connecting 9 Startkey 17 Summer time 23 Surface 25 Symbols explanation of 1 System settings BIOS Setup 19 System unit see Workstation T Task Manager 17 A26361 K670 Z100 1 7419 Technical data 25 Time incorrect 23 Time daylight savings 23 Tips 21 24 Transport 6 Trouble floppy disk 23 mouse 23 screen 22 workstation 21 Troubleshooting 21 U Unpacking 7 USB keyboard connecting 10 USB port 10 USB Universal Serial Bus 9 V Ventilation area 25 A26361 K670 Z100 1 7419 Index Video workstation 8 W Warm boot 17 Workstation anti theft protection 19 cabling 8 cannot boot 21 cleaning 6 connecting 8 indicators 15 lead seal 19 ports 9 setting up 8 switching off 14 switching on 14 switching on for the firsttime 13 transporting 6 Write protection floppy disk 18 English 29
5. and heat Provide at least 200 mm of clearance in front of and behind the fan area of the workstation to ensure adequate ventilation Do not cover the ventilation areas of the monitor and the workstation Do not place several workstations one above the other Connecting devices A The power plug must be disconnected Read the documentation on the external device before connecting it Do not connect or disconnect cables during a thunderstorm Always take hold of the actual plug Never unplug a cable by pulling the cable itself Connect and disconnect the cables in the order described below Route the cables so that no dangerous points tripping result Connecting cables e Turn off all power and equipment switches e Unplug all power plugs from the mains supply e Connect all cables at the workstation and peripherals Under all circumstances please observe the safety notes provided in the Important notes chapter e Plug all data communication cables into the utility sockets Plug all power cables into the mains supply Disconnecting cables e Turn off all power and equipment switches e Unplug all power plugs from the mains supply e Unplug all data communication cables from the utility sockets e Disconnect all cables from the workstation and peripherals 8 English A26361 K670 Z100 1 7419 Connecting devices Preparation for Use and Operation Ports for external devices The ports for external device
6. please do not have them installed by engineers or maintenance technical staff until after initial installation see the maintenance manual Steps for initial setup When starting up for the first time the devices monitor mouse keyboard etc are connected to the workstation and the software provided is set up When you set up the workstation for the first time you should carry out the following steps in the order shown 1 Decide where you are going to install the workstation 2 Connect the external devices to the workstation 3 Connect the workstation and the monitor to the mains voltage 4 Switch the workstation on and follow the instructions on the screen A26361 K670 Z100 1 7419 English 7 Preparation for Use and Operation Setting up the workstation Setting up the workstation AN When installing your workstation give consideration to the recommendations and safety notes in the Safety Guarantee and Ergonomics booklet Set up the workstation only in its correct orientation The points to observe are illustrated on the following pages We recommend that you place your equipment on a surface with good anti slip qualities In view of the multitude of different finishes and varnishes used on furniture it is possible that the rubber feet of the devices will mark the surface they stand on Do not expose the workstation to extreme environmental conditions see chapter Technical data Protect it from dust humidity
7. statement 5 First time switching on 13 Flashing power on indicator 15 Floppy disk cannot write 23 write protection 18 Floppy disk drive indicator 15 Function keys 16 G Game port 9 Guarantee coupon booklet 7 H Hard disk contents restoring 23 l Important notes 3 Indicator English 27 Index power on indicator fails to light 21 power on indicator green 15 Indicators workstation 15 Insufficient memory 24 Interfaces 9 Italics 1 K Kensington Lock 19 Key combination 17 Keyboard 16 cleaning 6 connecting 9 Keyboard port 9 Keys 17 L LAN port 9 Lead sealing 19 Linein 9 Line out 9 M Manuals further 24 Menu key 17 Microphone jack 9 Monitor cleaning 6 connecting 10 remains blank 22 transporting 6 Monitor port 9 Mouse cleaning 6 connecting 10 error 23 Mouse port 9 N New installation software 21 No picture 22 Not enough memory 24 Notational conventions 1 Note CE certificate 4 disposal 4 energy saving 4 important 3 manufacturer 4 safety 3 Num Lock key 17 Numeric keypad 16 28 English O Operation 7 Other manuals 24 Overview preparing for use 7 workstation 1 P Packing material 7 Parallel port 9 connecting devices 10 Ports external devices 9 Power switch 17 Power management 24 Power on indicator 15 Power on indicator dark 21 Preparing for first use overview 7 Preparing for use 7 overview 7 Problems 21 Property protection 19 PS 2 mouse port 9 R Recycling 4
8. to set your hardware configuration and system functions of the workstation When the device is delivered the default entries are valid see technical manual for the system board and for the BIOS Setup You may customise these settings to your requirements in the BIOS Setup The technical manual of the system board and for the BIOS Setup shows you how to start and use the BIOS Setup The menus and setting options provided by the BIOS Setup are also described in detail Property and data protection The software functions and mechanical lock on your workstation enable you to protect your system and personal data against unauthorised access By combining these options you can achieve maximum protection for your system Anti theft protection There are the following ways to protect your workstation from theft e with a chain and the eyelet a a Eyelet on casing A26361 K670 Z100 1 7419 English 19 Troubleshooting and tips Take careful note of the safety warnings in the Safety Warranty and Ergonomics booklet and in the Preparation for Use and Operation chapter when you connect or disconnect cables If a fault occurs try to correct it as described in the following places e inthis chapter in the documentation of the connected devices e inthe help systems of the software used e in the documentation of your operating system If you fail to correct the problem proceed as follows gt Switch off the workstat
9. 2001 edition Microsoft MS MS DOS Windows and Windows NT are registered trademarks of Microsoft Corporation VESA and DPMS are trademarks of Video Electronics Standards Association PS 2 is a registered trademark of International Business Machines Inc Pentium is a registered trademark of Intel Corporation USA Adobe and Acrobat are trademarks of Adobe Systems Incorporated and may be protected in certain countries All other trademarks referenced are trademarks or registered trademarks of their respective owners whose protected rights are acknowledged Copyright Fujitsu Siemens Computers GmbH 2001 All rights including rights of translation reproduction by printing copying or similar methods in part or in whole are reserved Offenders will be liable for damages All rights including rights created by patent grant or registration of a utility model or design are reserved Delivery subject to availability Right of technical modification reserved This manual was produced by cognitas Gesellschaft f r Technik Dokumentation mbH www cognitas de Contents Introduction Notational conventions Important NOTES ii ia Salely sni Manufacturer s notes m A MED tast Trnava a n e id ri re Dern daa tas Bisposalandrecyeling u sn02nena CE cefilleal usus FCC Class B Compliance Statement Transporting the workstation ise Cle
10. 50 EN 60950 UL 1950 CSA 22 2 No 950 l 100 V 240 V 50 Hz 60 Hz 400 W lt 200 W 470 mm 220 mm 460 mm ca 25 kg 245 N abh ngig von der Ausbaustufe DIN IEC 721 part 3 3 DIN IEC 721 part 3 2 15 C 35 C 25 C 60 C min 200 mm min 200 mm min 200 mm English 25 Index A Alphanumeric keypad 16 AltGrkey 17 Anti theft protection 19 Audio input 9 Audio output 9 B Battery disposal 4 BIOS Setup 19 Blank monitor 22 C Cable connecting 8 disconnecting 8 Casing lead sealing 19 CD ROM drive indicator 15 manual 24 CE certificate 4 Chain 19 Class B Compliance Statement 5 Cleaning 6 Clearance 25 Configuration BIOS Setup 19 Connecting cables 8 devices 8 keyboard 9 monitor 10 mouse 10 parallel port 10 serial port 10 standard keyboard 9 USB keyboard 10 Contents of delivery 7 Control key 17 Courier 1 Ctrl key 17 Ctrl Alt Del 17 Cursor control keys 16 D Data protection 19 Data technical 25 Date not correct 23 A26361 K670 Z100 1 7419 Devices connecting 8 interface 9 Dimensions 25 Diskette 18 Disposal 4 Drive hard disk indicator 15 E Electrical data 25 Electromagnetic compatibility 4 Energy saving 4 Enter key 17 Environmental conditions 25 Environmental data 25 Ergonomic video workstation 8 Error date 23 floppy disk 23 mouse 23 screen 22 time 23 workstation 21 Error message 23 Euro key 17 External devices connecting 8 ports 9 F FCC
11. 9 English 13 Preparation for Use and Operation Switching the workstation on and off Switching the workstation on gt Switch the monitor on see the operating manual for the monitor gt Press the ON OFF switch on the front of the workstation The power on indicator lights green the workstation is started If you have assigned the system password you must enter this when requested to do so in order to start the operating system Switching off the workstation gt Shut down the operating system properly Windows in the Start menu via the Quit function gt If the operating system does not automatically switch the workstation off turn the workstation off when requested to do so by pressing the ON OFF switch If the workstation is ready to operate the power on indicator flashes up green The workstation uses a minimum of electricity The ON OFF switch does not separate the workstation from the mains voltage To completely disconnect the mains voltage remove the power plug from the socket 14 English A26361 K670 Z100 1 7419 Indicators on the workstation Preparation for Use and Operation Indicators on the workstation CD ROM indicator Power on indicator Hard disk indicator Floppy disk indicator AUN Il 1 CD ROM indicator The indicator lights up when the CD ROM drive of the workstation is accessed You may only remove the CD when the indicator is dark 2 Power on indicator lights green The wor
12. aintenance manual may only be performed by engineers or maintenance technical staff e Only qualified technicians should repair the device Disregarding these instructions can endanger the user electric shock risk of fire and or damage the device For this reason opening the unit without authorisation engineers or maintenance technical staff voids the warranty and cancels any liability e During installation and before operating the device please observe the instructions on environmental conditions in the chapter entitled Technical data as well as the instructions in the chapter Preparation for Use and Operation e Ifthe device is brought into the installation site from a cold environment condensation both inside and on the cover can form Before operating the device wait until it is absolutely dry and has reached approximately the same temperature as the installation site Failure to observe these guidelines can lead to material damage of the device The device automatically sets itself to the correct rated voltage from 100 V to 240 V Ensure that the local mains voltage lies within these limits The power button does not separate the workstation completely from the mains voltage To completely disconnect the mains voltage remove the power plug from the grounded mains outlet A26361 K670 Z100 1 7419 English 3 Important notes Manufacturer s notes Manufacturer s notes Keep this operating manual together w
13. aning the WOIKStellOEi oontra e Pe E iat idee ERREUR Preparation for Use and Operation cc Unpacking and checking the delivery Steps for initial setup Setting up the workstation Connecting devices Ports for external devices Connecting the keyboard Connecting the mouse Connecting devices with a serial or a parallel connection i Connecting the monitor to the electricity supply 10 Connecting the workstation to the mains voltage 511 Switching the workstation on and Off nere ee ile Switching on the workstation for the first time Switching the workstation on ne Switching off the WOIKSIAIIOH ciet cicer meti intet eit rp iren Indicators on the workstation is Keyboard teer ig Important keys and key combinations Working with floppy disks i Settings In BIOS SOME PE Property and idata Protection MPH tinas Ant theft protec RT Troubleshooting A os 21 Installing New software rece terris etin Deed cre ten hakkad e dee 21 Power on indicator remains unlit after you have switched on your device is The screen stays blank 222 No mouse pointer displayed on the screen er The floppy disk cannot be read or written 23 Time and or date is not correct 23 E
14. end of the keyboard cable square plug into the socket on the underside of the keyboard gt Insert the rectangular USB plug of the keyboard cable into the USB port lt on the system unit Connecting the mouse gt Plug the connector of the mouse cable into the mouse port If you do not attach a mouse at the PS 2 mouse port you can disable the mouse controller in the BIOS Setup in order to free the IRQ12 for a different application Connecting devices with a serial or a parallel connection gt Connect the data cable to the external device gt Connect the data cable of the external device to the appropriate port on the workstation operating system already includes many drivers But if the driver you need is not on the hard disk please install it from the floppy disk or CD supplied with the device or with the application programme If you need to change the settings of the serial or parallel port e g address interrupt you can do so in the BIOS Setup The possible settings for the interfaces are described in the technical manual for the system board and for the BIOS Setup i Most devices that you connect to the serial or parallel port require special drivers Your Connecting the monitor to the electricity supply gt Follow the instructions contained in the monitor manual to prepare the monitor for operation gt Plug the data cable of the monitor into the monitor port of the workstation Plug the power cable o
15. f the monitor into the grounded mains outlet 10 English A26361 K670 Z100 1 7419 Connecting the workstation to the mains voltage Preparation for Use and Operation Connecting the workstation to the mains voltage gt Plug the workstation s power cable into the workstation 1 and then into the grounded mains outlet 2 A26361 K670 Z100 1 7419 English 11 Preparation for Use and Operation Switching the workstation on and off Switching the workstation on and off 1 Power button 2 Power on indicator Workstation is ready for operation The power on indicator 2 flashes green In this mode you can switch the workstation on with the ON OFF switch 1 The ready to operate status corresponds to the stand by status of a TV set A full description of the power on indicator 2 can be found in the Indicators on the workstation section Workstation is on The power on indicator 2 lights green The workstation can be switched ready to operate with the ON OFF switch 1 12 English A26361 K670 Z100 1 7419 Switching the workstation on and off Preparation for Use and Operation Switching on the workstation for the first time When you switch on your workstation for the first time the supplied software is set up and configured You should plan some time for this as this process must not be interrupted network protocol are required Contact your network administrator or network i If the workstation is i
16. iled information can be found in the User Guide of the mouse or application programme The floppy disk cannot be read or written gt Check whether the write protection of the floppy disk is activated gt Check the relevant entries for Diskette A or B in the Main menu of the BIOS Setup Time and or date is not correct gt Set the time and or date You can set the time and date in the BIOS Setup or in the operating system If the time and date are repeatedly wrong when you switch on your PC the on board battery is flat Have the lithium battery changed by engineers or maintenance technical staff see maintenance manual Error messages on the screen Error messages and their descriptions are listed in the technical manual of the system board and for the BIOS Setup and in the documentation of the installed software Restoring the hard disk contents gt The instructions for this is contained in the manual First Steps Windows NT 4 0 Setup A26361 K670 Z100 1 7419 English 23 Troubleshooting and tips Tips The workstation cannot be switched off with the ON OFF switch Cause The workstation has not been switched on with the ON OFF switch gt Press the power button again Cause System crash gt Press and hold the power button for at least four seconds until the device switches off Out of system resources If you have too many applications running at once you may experience problems due to a lack of system res
17. indows Details of other keys and key combinations can be found in the documentation of the relevant application programme ON OFF switch Depending on the setting in the BIOS setup the system can be switched on or off with this switch With Windows 98 with ACPI or with Windows 2000 you can set additional functions of the power button in the Control Panel On some keyboards the power button can only be used with ACPI Otherwise the key is inoperative Enter key confirms or starts the marked selection The enter key is also referred to as the Return key Start key calls up the Windows Start menu Menu key invokes the menu for the marked item Windows Shift key enables upper case letters and the upper key symbols to be used Alt Gr e g German keyboard produces a character shown on the right hand side of a key e g the character on the key BJ Euro key outputs the Euro symbol when pressed simultaneously with the key Num Lock key Lock by pressing the Num Lock key you switch between the Numeric keypad cursor control functions and digit or comma functions When the Num Lock indicator is lit the digit and comma keys are active When the Num Lock indicator is not lit the cursor control functions are active in the Numeric keypad Ctrl key Ctrl starts key combination actions Warm boot Ctrl Alt restarts the workstation First hold down the and keys and then press the key With Windows 98 Windows 2000
18. ion gt Make a note of the steps and the circumstances that led to the fault Also make a note of any error messages displayed and the Ident No of your device Contact your sales outlet or our customer service centre Installing new software When installing programmes or drivers important files may be overwritten and modified To be able to access the original data in the case of any problems following installation you should backup your hard disk prior to installation Power on indicator remains unlit after you have switched on your device This may be due to the following The mains voltage supply is faulty gt Check that the power cable is plugged properly into the workstation and grounded mains outlet Internal power supply overloaded gt Disconnect the power plug of the workstation from the grounded mains outlet Waitfor a moment gt Plug the power plug into the grounded mains outlet again A26361 K670 Z100 1 7419 English 21 Troubleshooting and tips The screen stays blank If your screen remains blank this may be due to the following Monitor is switched off gt Switch your monitor on Power saving has been activated screen is blank gt Press any key on the keyboard or gt Deactivate the screen saver Enter the appropriate password Brightness control is set too dark gt Adjust the brightness control For detailed information please refer to the operating manual supplied with your moni
19. ith your device If you pass on the device to third parties you should include this manual Energy saving When the device is delivered some energy saving functions are already set see the technical manual for the system board and for the BIOS Setup e Switch the workstation off when you are not using it e Inthe BIOS Setup you may set further energy saving functions for the workstation see the Technical Manual of the system board and for the BIOS Setup Disposal and recycling This device has been manufactured to the highest possible degree from materials which can be recycled or disposed of in a manner that is not environmentally damaging The device may be taken back after use to be recycled provided that it is returned in a condition that is the result of normal use Any components not reclaimed will be disposed of in an environmentally acceptable manner Do not throw lithium batteries into the household waste They must be disposed of in accordance with local regulations concerning special waste If you have any questions about disposal of the batteries or system please contact your local sales outlet or Fujitsu Siemens Computers GmbH Recyclingcenter D 33106 Paderborn Tel 49 0 5251 81 80 10 Fax 49 0 5251 81 80 15 CE certificate The shipped version of this device complies with the requirements of the EEC directives C 89 336 EEC Electromagnetic compatibility and 73 23 EEC Low voltage directive 4
20. kstation is on flashing green The indicator only flashes on systems which support the ACPI function Advanced Configuration and Power Management Interface The workstation is in the energy saving mode standby After being switched on with the ON OFF switch the workstation returns to the state it was in before the energy saving mode In the energy saving mode the workstation may not be disconnected from the mains supply as this may otherwise result in data loss does not glow The workstation is switched off 3 Hard disk indicator The indicator lights up when the hard disk drive of the workstation is accessed 4 Floppy disk indicator The indicator lights up when the floppy disk drive of the workstation is accessed You may only remove the floppy disk when the indicator is unlit A26361 K670 Z100 1 7419 English 15 Preparation for Use and Operation Keyboard Keyboard E 2 HAGA UM SRD LC JC JL LC CC LJ Ltt tt ttt tt Ltt tt tt DOLL LOL JOO Le LIU 3 1 Function keys 4 Cursor keys 2 Power button optional 5 Numeric keypad calculator keypad 3 Alphanumeric keypad i The illustrated keyboard is an example and may differ from the model you use 16 English A26361 K670 Z100 1 7419 Keyboard Preparation for Use and Operation Important keys and key combinations The following description of keys and key combinations refers to MS W
21. ng with a dry cloth If particularly dirty use a cloth that has been moistened in mild domestic detergent and then carefully wrung out Cleaning the keyboard and the mouse Use disinfectant wipes to clean the keyboard and the mouse The mouse mechanism and the mouse ball can be cleaned by removing the retaining ring on the underside of the mouse gt Using two fingers push the retaining ring and turn the ring in the direction of the arrows Remove the retaining ring and the rotating ball Clean the ball and the three small wheels in the mouse with a lint free cloth Replace the ball and the retaining ring Using two fingers push the retaining ring and turn the ring in the opposite direction of the arrows You should feel the ring engage gt gt gt gt 6 English A26361 K670 Z100 1 7419 Preparation for Use and Operation Please take note of the safety information in the Important notes chapter Unpacking and checking the delivery It is recommended not to throw away the original packaging material It may be required for reshipment at some later date gt Unpack all the individual parts gt Check the delivery for damage incurred during transportation gt Check whether the delivery agrees with the details in the delivery note Should you discover that the delivery does not correspond to the delivery note notify your local sales outlet immediately If you have received drives or boards with your Workstation
22. ntegrated into a network the user and server details as well as the administrator if you have any questions about these details For initial start up of Windows NT the manual First Steps Windows NT 4 0 Setup provides an overview of the required information If you have received data from your network or network administrator then please enter this data in the spaces provided in the First Steps manual This simplifies first time installation You may require the Windows licence number during installation This number is located on a Sticker on your workstation gt Switch your monitor on gt Switch the workstation on with the ON OFF switch The power on indicator lights green and the workstation is started gt Adjust the brightness if necessary see the operating manual for the monitor gt During installation follow the instructions on screen Once the installation has been started the workstation must not be switched off You should only reboot the workstation during installation if you are requested to do so Otherwise the installation will be not be performed correctly If a fault occurs during the installation the contents of the hard disk must be completely restored Consult the operating system manual if there is anything unclear about the requested input data Further information about the system drivers utilities updates manuals etc is contained on the Drivers amp Utilities CD A26361 K670 Z100 1 741
23. ources If this happens you should close applications you do not require or call the applications in a different order BIOS settings in power management do not become active The Auto insert notification setting may be active for the CD ROM drive This setting causes Windows 9x to inquire about any modifications on the drive at regular intervals Because of this the timer for the idle time cannot time out To activate power management proceed as follows gt In Windows 9x select Start Settings Control Panel System Device Manager CD ROM gt Select the installed CD ROM drive from the list gt Select Settings gt Deactivate the Auto insert notification box CD ROM drive Information on the CD ROM drive can be found in the CD ROM drive manual or on the Drivers amp Utilities CD Other manuals Other manuals are contained on the Drivers amp Utilities CD 24 English A26361 K670 Z100 1 7419 Technical data Electrical data Regulations complied with Protection class Rated voltage range Frequency Max rated current Typical power draw in operation Dimensions Width depth height Typical Weight Environmental conditions Environment class 3K2 Environment class 2K2 Temperature e Operation 3K2 e Transport 2K2 Condensation in operating must be avoided Clearance required to ensure adequate ventilation left hand side e front e rear A26361 K670 Z100 1 7419 1EC609
24. p Fujitsu Siemens Computers GmbH is not responsible for any radio or television interference caused by unauthorised modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu Siemens Computers GmbH The correction of interference caused by such unauthorised modification substitution or attachment will be the responsibility of the user The use of shielded I O cables is required when connecting this equipment to any and all optional peripheral or host devices Failure to do so may violate FCC rules A26361 K670 Z100 1 7419 English 5 Important notes Transporting the workstation Transporting the workstation Transport all parts separately in their original packaging or in a packaging which protects them from knocks and jolts to the new site Do not unpack them until all transportation manoeuvres are completed Never drop the monitor risk of implosion Cleaning the workstation Turn off all power and equipment switches and pull the power plug out of the grounded mains outlets The inside of the workstation housing may only be cleaned by authorised specially trained personnel Do not use any cleaning agents that contain abrasives or may corrode plastic Ensure that no liquid enters the system Ensure that the ventilation areas of the workstation and the monitor are free Cleaning the workstation and the monitor Wipe the workstation and monitor casi
25. rror messages on the screen Restoring the hard disk contents n e 24 A26361 K670 Z100 1 7419 Deutsch Introduction Your CELSIUS Personal Workstation is a high end workstation for the most demanding applications from 3D CAD applications to 3D Studio applications right up to numerical simulations and real time animations of textured objects This operating manual tells you how to put your workstation into operation and how to operate it in daily use Your workstation is available in various configuration levels which differ in hardware and software equipment In addition you can have installed accessible drives e g DAT drive and hard disks as well as other boards Depending on the workstation the operating system drivers and software utilities are pre installed on the hard disk to facilitate the procedure when you use your workstation for the first time Your workstation has a number of security features to ensure that no unauthorised persons can access your data For example you can activate a screen saver with password protection The security functions in the BIOS Setup also allow you to protect your data by means of passwords Additional information on this workstation is also contained in in the maintenance manual for the workstation in the Safety Warranty and Ergonomics booklet in the manual First Steps Windows NT 4 0 Setup in the operating man
26. s are on the rear and on the front of the workstation The ports available on your device depend on the configuration level you have selected The standard ports are marked with the symbols shown below or similar Exact details of the position of the ports are supplied in the technical manuals for the boards Keyboard port purple 1 Serial interface 1 turquoise B PS 2 mouse port green Serial interface 2 turquoise CJ Monitor port blue a USB port black Parallel interface Printer burgundy Game port gold Im B B SmartCard reader A Microphone jack mono pink noa oo 3 Audio output Line out lime green LAN connector Audio input Line in light blue SCSI connection Dep Some of the devices that you connect require special drivers see the operating system and device documentation Connecting the keyboard Depending on the selected equipment level your workstation will be supplied with a standard keyboard or a USB keyboard Connecting standard keyboard Use the supplied keyboard cable only gt Plug the other end of the keyboard cable square plug into the socket on the underside of the keyboard gt Plug the round keyboard cable connector into the port marked with this symbol on the system unit A26361 K670 Z100 1 7419 English 9 Preparation for Use and Operation Connecting devices Connecting USB keyboard Use the supplied keyboard cable only Plug the other
27. tor Power cable or monitor cable not connected gt Switch off the monitor and the workstation gt Check whether the power cable is properly connected to the monitor and to the mains outlet gt Check that the monitor cable is properly connected to the workstation and monitor if not permanently attached gt Switch on the monitor and the workstation Wrong monitor has been set under Windows NT gt Restart the workstation in standard VGA mode gt Set the desired resolution in the Control Panel window using the Display programme and adjust the monitor display as described in the operating manual for the monitor The wrong RAM modules have been inserted gt See the technical manual for the system board for information on which memory modules can be used 22 English A26361 K670 Z100 1 7419 Troubleshooting and tips No mouse pointer displayed on the screen gt Shutdown the operating system properly v Switch off the workstation gt Check that the mouse cable is properly connected to the system unit If you use an adapter or extension lead with the mouse cable check the connections gt Make sure that only one mouse is connected gt Switch the workstation on gt The mouse controller must be enabled if you use a PS 2 mouse Check in the BIOS Setup that the mouse controller is Enabled gt Checkthat the mouse driver is properly installed and is present when the application programme is started Deta
28. ual for the monitor in the technical manual for the system board and for the BIOS Setup in the information files e g TXT DOC WRI HLP in the manuals of the built in boards SCSI controller graphics card network adapter computer These manuals can be read and printed with the programme Acrobat Reader i Some of the manuals listed can be found on the Drivers amp Utilities CD provided with your contained on the CD Notational conventions The meanings of the symbols and fonts used in this manual are as follows Pay particular attention to texts marked with this symbol Failure to observe this warning endangers your life destroys the workstation or may lead to loss of data i Supplementary information remarks and tips follow this symbol gt Text which follows this symbol describes activities that must be performed in the order shown Text in this typeface indicates screen outputs Text in italics indicates commands or menu items Quotation marks indicate names of chapters or terms A26361 K670 Z100 1 7419 English 1 Important notes In this chapter you will find information regarding safety which it is essential to take note of when working with your workstation The manufacturer s notes contain helpful information on your workstation Safety Pay attention to the information provided in the Safety Warranty and Ergonomics booklet and to the following notes e _ The activities described in the m
Download Pdf Manuals
Related Search
Related Contents
TA-50 mini power amp module user manual Manuel de l`opérateur Kapitel 2 Premium Hardwired Electronic Chime Owner`s Manual valve à la demande O2/N2O DWX-51D Setup Guide Philips Power2Charge SCM4480 Universal USB charger VPG 3.4 User Manual Copyright © All rights reserved.
Failed to retrieve file