Lexmark Optra T610 Laser Printer
Contents
1. 6 Rotate the tray up until the upper tabs click into the upper slots 7 Attach the top cover to the output expander Install Paper Options and Printer 11 Installing a 5 Bin Mailbox Tne 5 bin mailbox is shipped with a sheet of labels and a plastic bracket for attaching a paper bail After you carefully unpack the 5 bin mailbox install it immediately otherwise the edges of the mount ing brackets could damage tabletops or fabrics N D N V 4 Labels V N D N D on N Optra T label colored triangle Warning The 5 bin mailbox is designed to hold the weight of print material only Do not use it as a shelf excess weight may damage it 1 Remove the top cover from the printer or previously installed output expander or 5 bin mailbox 2 Slide the plastic bracket onto the static brush holder located near the bottom of the 5 bin mailbox NNA B D X 12 Install Paper Options and Printer ARR h M Mounting slot Mounting bracket Attaching Labels to Output Expanders and 5 Bin Mailboxes Labels 3 Insert the mounting brackets into the slots on top of the printer output expander or 5 bin mailbox Make sure the 5 bin mailbox is seated securely Note If the 5 bin mailbox will be the topmost output option remove the paper bail from the bracket on the top cover and store in a safe place 4 Attach the2. 2 Lift open the envelope feeder connector Release latch door Envelope feeder connector door 3 Align the tabs on the envelope feeder with the slots on both sides of the printer and gently push the envelope feeder into the opening until it snaps into place The envelope feeder tilts downward at a slight angle when it is installed properly 14 Install Paper Options and Printer Step 2 Install Memory and Optional Cards eee __ v Accessing the Printer System Board You must access the printer system board to install printer memory flash memory or an optional card 1 Make sure the printer power is off the printer power cord is unplugged and all cables are disconnected from the back of the printer 2 Press the release latches to open the upper and lower front doors 3 Press down on the side door latches and open the side door 4 Loosen but do not remove the six screws as shown Install Memory and Optional Cards 15 5 Use the tabs to slide the shield up until the top three screws fit into the three keyholes on the shield 6 Hold the shield by the tabs and lift it off Tab Installing Printer Memory or Flash Memory 1 Follow the steps under Accessing the Memory connector 1 Printer System Board beginning on page 15 Memory connector 2 Memory connector 3 T616 n and T614 n models only Warning Electronic components can be damaged by static electricity Touc
3. LEXMARK Setup Guide First Edition June 1999 The following paragraph does not apply to any country where such provisions are inconsistent with local law LEXMARK INTERNATIONAL INC PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIM ITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Some states do not allow disclaimer of express or implied warranties in certain transactions therefore this statement may not apply to you This publication could include technical inaccuracies or typographical errors Changes are periodically made to the information herein these changes will be incorporated in later editions Improvements or changes in the products or the programs described may be made at any time A form for the reader s comments is provided at the back of this publication If the form has been removed comments may be addressed to Lexmark Inter national Inc Department F95 035 3 740 West New Circle Road Lexington Kentucky 40550 U S A In the United Kingdom and Eire send to Lexmark International Ltd Marketing and Services Department Westhorpe House Westhorpe Marlow Bucks SL7 3RQ Lexmark may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you You can purchase additional copies of publications related to this product by calling 1 800 553 9727 In the United
4. 7 8 Attaching the Paper Bail Install Paper Options and Printer Note Attach the paper bail to the top cover only if you do not plan to install a 5 bin mailbox as the top output option 1 Remove the top cover of the printer and slide the plastic bracket onto the static brush holder Adjust the bracket so it is centered over the exiting paper 2 Place the tips of the wire paper bail into the ends of the plastic bracket so that the bail curves downward 3 Replace the top cover Decals showing the number 1 are on your printer and the standard input tray as shown These decals keep the standard input tray paired with the printer If you purchased an Optra T616 n or T614n printer or optional drawers you received a sheet of decals Peel the decals from the sheet and attach them to the recessed areas on the drawer and the match ing tray as shown Removing the Print Cartridge and Packaging 1 Push the release latch and open the upper front door of the printer 2 Grasp the print cartridge by the handgrip and pull the print cartridge up and out 3 Pull on each end of the plastic V shaped piece and then pull the packaging material straight out Discard all packaging material 4 Reinstall the print cartridge Align the slides on the print cartridge with the slots on the print cartridge cradle Use the colored arrows inside the printer for placement 5 Guide the print cartridge down as it drops and
5. Kingdom and Eire call 0628 481500 In other countries contact your point of purchase References in this publication to products programs or services do not imply that the manufacturer intends to make these available in all countries in which it operates Any reference to a product program or service is not intended to state or imply that only that product program or service may be used Any functionally equivalent product program or service that does not infringe any existing intellectual property right may be used instead Evaluation and verification of operation in conjunction with other products programs or services except those expressly designated by the manufacturer are the user s responsibility Lexmark MarkNet MarkVision and Optra are trademarks of Lexmark International Inc registered in the United States and or other countries Other trademarks are the property of their respective owners Copyright 1999 Lexmark International Inc All rights reserved UNITED STATES GOVERNMENT RESTRICTED RIGHTS This software and documentation are provided with RESTRICTED RIGHTS Use duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph c 1 ii of the Rights in Technical Data and Computer Software clause at DFARS 252 227 7013 and in applicable FAR provi sions Lexmark International Inc Lexington KY 40550 FCC Emissions Information This device complies with Part 15 of the FCC
6. Place the duplex unit on top of any installed paper drawers or the table or printer cabinet where you plan to use the printer The tab round hole and square holes on top of any drawer will help you seat the duplex unit so the edges are aligned properly Make sure it is securely in place To attach the printer see Placing the Printer on page 7 Placing the Printer Caution Make sure your fingers are not under the printer when you set it down Use the handholds on the printer or ask someone to help you lift it Handhold Tab Round hole Note In order to ensure adequate clearance when installing system board options see Install Memory and Optional Cards on page 15 before you place the printer if you plan to e install memory or option cards and e will have less than 605 6 mm 24 in clearance on the left side of the printer Ask someone to help you lift the printer by the handholds and lower it onto the duplex unit optional drawer table or printer cabinet The tab round hole and square holes on top of any drawer or unit will help you seat the printer so the edges are aligned properly Make sure the printer is securely in place To attach output options If your printer supports output options see Installing an Output Expander on page 10 Installing a 5 Bin Mailbox on page 12 Installing a High Capacity Output Stacker on page 14 Install Paper Options and Printer
7. or output options 1 of each or 1 of each or 1 high capacity 1 high capacity 1 high capacity output stacker output stacker or output stacker or 1 output expander and 1 output expander and 1 high capacity 1 high capacity output stacker output stacker Optra T616 T616n Optra T614 T614n Optra T612 T612n Optra T610 T610n Attach up to Attach up to Attach up to Attach up to 3 additional optional 4 optional drawers 3 optional 3 optional drawers Optra T614 drawers drawers 3 additional optional drawers Optra T614n ships with an extra 500 sheet drawer 2000 Sheet Drawer 250 Sheet Drawer 500 Sheet Drawer Duplex Unit Envelope Feeder Install Paper Options and Printer 3 4 Installing the 2000 Sheet Drawer Optra T label colored triangle Install Paper Options and Printer Your printer supports one 2000 sheet drawer It gives your printer added capacity by letting you load up to four reams approximately 2 000 sheets of 20 lb paper The 2000 sheet drawer is packaged with a User s Guide that contains detailed instructions for instal lation setup and use including loading paper and removing paper jams When you have finished installing the 2000 sheet drawer install any drawers or a duplex unit that you have purchased Installing a 250 Sheet or 500 Sheet Drawer Tray labels Optra T label colored triangle Support unit Paper tray Tab Round hole Paper drawers attach under the p
8. snaps into place 6 Close the upper front door Install Paper Options and Printer 9 Installing an Output Expander Each output expander consists of the expander and a removable tray A paper bail bracket and labels are also included Optra T label colored triangle After you carefully unpack the output expander install it immediately otherwise the edges of the mounting brackets could damage tabletops or fab rics Bracket and bail Warning The output expander tray is designed to hold the weight of print material only Do not use it as a shelf excess weight may cause it to disengage from the output expander 1 Remove the top cover from the printer or previously installed output option 2 Slide the plastic bracket onto the static brush holder located near the bottom of the output expander 10 Install Paper Options and Printer 3 Insert the mounting brackets into the slots on top of the printer or output option Make sure the output expander is seated securely Mounting bracket Mounting slot Note Do not attach the paper bail unless you are mounting the output expander on the printer or another output expander 4 Place the tips of the wire paper bail into the ends of the plastic bracket so that the bail curves downward The bail rests in the output tray of the expander below it or in the printer output bin 5 Slide the lower tabs on the tray into the lower slots on the output expander
9. top cover to the 5 bin mailbox Note Do not attach the paper bail unless you are mounting the 5 bin mailbox on the printer or an output expander 5 Place the tips of the wire paper bail into the ends of the plastic bracket so that the bail curves downward The bail rests in the output tray of the expander below it or in the printer output bin 6 Adjust the paper stops for the paper size you will use If you purchased an output expander or 5 bin mail box you received a sheet of labels These labels are provided so that you may label your various output bins The illustration indicates some places where you may attach the labels output bin tray paper stop side cover or wherever best suits your application Install Paper Options and Printer 13 Installing a High Capacity Optra T printer models T616 n T614 n and Output Stacker T612 n support one high capacity output stacker The high capacity output stacker is packaged with installation instructions Optra T label colored triangle Installing the Envelope Feeder The envelope feeder attaches to the front of your printer behind the lower front door It can be removed when you are not using it making the Optra T label printer more compact colored triangle Refer to the User s Guide available on the Optra T Publications CD for information on using the enve lope feeder 1 Push the release latch and open the lower front door of the printer
10. Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Any questions on this statement should be directed to Director of Lab Operations Lexmark International Inc 740 West New Circle Road NW Lexington KY 40550 606 232 3000 Please see the online User s Guide for further information Safety Information e If your product is NOT marked with this symbol El it MUST be connected to an electrical outlet that is properly grounded e The power cord must be connected to an electrical outlet that is near the product and easily accessible e Refer service or repairs other than those described in the operating instructions to a professional service person e This product is designed tested and approved to meet strict global safety standards with the use of specific Lexmark components The safety features of some parts may not always be obvious Lexmark is not responsible for the use of other replacement parts e Your product uses a laser exercise CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure e Your product uses a printing process that heats the print media and the heat may cause the media to release emissions You must understand the section in your o
11. h something metal on the printer before you touch the memory option 2 Unpack the memory option Avoid touching the connection points along its edge Save cain a the packaging materials C tion point a a 3 Open both latches completely Insert the memory option straight into the connector ya with the connection points pointing toward the system board as shown 4 Push the memory card firmly into the connector until it snaps into place Make sure each latch fits over the notch located on either side of the option card 5 See Reattach Shield and Close Doors beginning on page 18 to reattach the shield and side door 16 Install Memory and Optional Cards
12. location of the label is shown before each option install section If you encounter a problem while setting up the printer refer to the User s Guide available on the Optra T Publications CD for more information Setup Install Paper Options and Printer Install Memory and Option Cards Printer Flash Memory 2 Page 16 5 Bin Mailbox Page 12 Output Expander Page 10 Access printer system board Page 15 Option Cards Page 17 Load Paper 3 See Page 19 High Capacity Output Stacker Page 14 Print Cartridge Printer Page 9 Page 7 Envelope Feeder Page 14 Duplex Unit Page 6 Parallel Cable Page 20 Serial Cable Page 20 Power Cord Page 21 250 Sheet Drawer Page 5 Verify Setup 5 See Page 22 Order of Installation 500 Sheet Drawer Page 5 Configure Network Printer 6 See Page 23 TCP IP Page 24 Novell NetWare Page 28 AppleTalk Page 29 OS 2 Warp Server Page 29 2000 Sheet Drawer Page 4 Option install order may be reversed Step 1 Install Paper Options and Printer E Paper Options Supported The table illustrates various combinations of paper options supported by your printer All models sup port a duplex unit and envelope feeder High Capacity Output Stacker Output Expander 5 Bin Mailbox Attach up to Attach up to Attach up to 3 output expanders 3 output expanders 2 output expanders Does not support 2 5 bin mailboxes 2 5 bin mailboxes 1 5 bin mailbox
13. perating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions Getting Started eee __ av_ 137 16 cm Lc 7 1 gi S 4 ft 7 I San 13sec A lt 7 WES ea SA A i pe 304 8 mm 304 8 mm 12 in 12in 508 mm 304 8 mm 20 in 12 in Printer aE CDs Paper bail Di bracket lt Operator panel overlay non English only Handhold Power switch cover Power cord Tray number decals Optra 500 Sheet Drawer Optra T616 n T616 n and T614n models only and T614n models only Turn Off the Printer Options Compatibility Troubleshooting 1 Select a well ventilated place to set up your printer Make sure you have a sturdy low table or the optional printer stand on which to set the printer 2 Remove all items from the box except the printer If any items are missing contact the place where you bought the printer Save the carton and packing material in case you need to repack the printer for ser vice or storage Note Leave the printer in the box until you are ready to install it Then ask someone to help you lift the printer using the hand holds If your printer is already set up make sure the printer power is off and the power cord and any cables are unplugged before installing any options Options compatible with Optra T printers are labeled with a colored triangle The
14. rinter and optional duplex unit The printer automatically rec ognizes any drawer that has been installed A drawer consists of a paper tray and a support unit The 250 sheet drawer and the 500 sheet drawer are installed the same way 1 Remove the tray from the support unit Remove all packing material and tape from both the support unit and the tray 2 Place the support unit on top of any previously installed paper drawers or the table or printer cabinet where you plan to use the printer The tab round hole and square holes on top of any drawer will help you seat the support unit so the edges are aligned properly Make sure the support unit is securely in place At this point attach another optional drawer a duplex unit or the printer To attach a drawer repeat steps 1 and 2 To attach a duplex unit see Installing a Duplex Unit on page 6 To attach the printer see Placing the Printer on page 7 Install Paper Options and Printer 5 6 Installing a Duplex Unit Duplex unit for Optra T610 n Duplex unit for Optra T616 n T614 n and T612 n back cover curves inward Optra T label colored triangle Square hole Round hole Install Paper Options and Printer The duplex unit attaches under the printer below the standard input tray and above any paper drawers Refer to the printer User s Guide available on the Optra T Publications CD for information on using the duplex unit 1
Download Pdf Manuals
Related Search