SMC EZ Connect Modem
Contents
1. Reorient the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Part 68 The modem is registered with the FCC as compliant with the rules of Part 68 and use of this modem is subject to the following restrictions 1 The Federal Communication Commission FCC has established rules which permit this device to be directly connected to the telephone network Standardized jacks are used for these connections This equipment should not be used on party lines or coin phones 2 If this device is malfunctioning it may also be causing harm to the telephone network this device should be disconnected until the source of the problem can be determined and until repair has been made If this is not done the telephone company can temporarily disconnect service 3 The telephone company may make changes in its facilities equipment operation and procedures if such changes affect the compatibility or use of this device the telephone company is required to give adequate notice of the changes You will be advised of your right to file a complaint with the FCC 4 If the telephone company requests information on what equipment is connected to their lines inform them of a The telephone number to which this unit is connected b The ringer eq2. Check the following troubleshooting points before contacting SMC Technical Support You Cannot Connect to the Network Check the phone and USB cables for wear or loose wires and replace any defective cables if necessary Make sure the cable is securely attached to the modem s RJ 11 port and that the modem is connected to your ADSL service provider via an RJ 11 wall socket or splitter If your PPP connection fails to respond hang up and dial again PPP may fail to connect when you first dial in due to synchronization problems If the Data LED is off review the driver installation process to be sure that the driver was correctly installed Make sure the correct software driver was installed for your operating system A failed or aborted installation may leave some system files or drivers that interfere with a new installation If necessary remove the EZ Connect ADSL USB Modem driver and try reinstalling it You Cannot Connect to the Internet Click on the Network icon in the Control Panel and enter the required TCP IP settings specified by your Internet Service A 1 TROUBLESHOOTING Provider Then reboot your computer to enable the new settings A 2 APPENDIX B SPECIFICATIONS ADSL Specifications Standards Conformance Basic ADSL ANSI T1 413 Issue II full rate ADSL ITU G 992 1 G dmt ITU G 992 2 G lite G 994 1 G hs Transport Protocols RFC 1557 IP ATM RFC 2364 PPP ATM ATM Attributes ATM Transm
3. 2 x1 Bindings Advanced NetBIOS DNS Configuration Gateway wins Configuration IP Address The first gateway in the Installed Gateway list will be the default The address order in the list will be the order in which these machines are used New gateway Installed gateways B 15 Hene To add a new gateway type the address in the New gateway field and click Add The new gateway will appear in the Installed gateways list To remove a previously installed gateway highlight the entry to be removed in the Installed gateways list and click Remove The gateway will no longer appear in the Installed gateways list Click OK from the TCP IP Properties window The Network window will reappear Click OK to end the modifying TCP IP options session If you have made changes to TCP IP properties you will be asked to restart reboot your PC Click Yes and your PC will restart Moopiryinc TCP IP NETWORKING OPTIONS Microsoft Windows 2000 TCP IP settings are automatically set up during the software installation process The following procedure may be used to change TCP IP settings if necessary 1 From the PC desktop right click the My Network Places icon and select Properties 2 Double click the SMC Local Area Connection icon from the Network and Dial Up Connections window Note The icon name may differ from that specified above The SMC connection icon will be ident
4. effect Click Finish 4 A message will be displayed confirming that you want to reboot the system click Yes 5 Once the PC has rebooted installation of the EZ Connect ADSL USB Modem is complete DRIVER INSTALLATION Note Regardless of the driver type installed the installation procedure will automatically configure the TCP IP settings If you need to change these settings refer to Chapter 4 Modifying TCP IP Networking Options 3 9 DRIVER INSTALLATION 3 10 CHAPTER 4 Moptryinc TCP IP NETWORKING OPTIONS WAN USB Driver Microsoft Windows 98 First and Second Editions TCP IP settings are automatically set up during the software installation process The following procedure may be used to change TCP IP settings if necessary 1 2 From your PC desktop double click the My Computer icon From the My Computer window double click the Dial Up Networking icon From the Dial Up Networking window right click on the SMC Dial Up PPP Connection icon and click Properties 2 Dial Up Networking BEE Eie Edt View Go Favorites Connections Help EJ 5 9 B SX B 2x Back Undo Address Forward Up Create Dial Cut Copy Paste Delete a Connecti Dial up nection Networking M i Create Shortcut Delete SMC Dial Up PPP Rename Connection PPP ATM Adapter Device name DSLWanUsb LineO To establish a dial up connection to this network Di
5. AS WARRANTED ABOVE CUSTOMER S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN QUESTION AT SMC S OPTION THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS EXPRESS OR IMPLIED EITHER LIMITED WARRANTY IN FACT OR BY OPERATION OF LAW STATUTORY OR OTHERWISE INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE OR USE OF ITS PRODUCTS SMC SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER S OR ANY THIRD PERSON S MISUSE NEGLECT IMPROPER INSTALLATION OR TESTING UNAUTHORIZED ATTEMPTS TO REPAIR OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE OR BY ACCIDENT FIRE LIGHTNING OR OTHER HAZARD LIMITATION OF LIABILITY IN NO EVENT WHETHER BASED IN CONTRACT OR TORT INCLUDING NEGLIGENCE SHALL SMC BE LIABLE FOR INCIDENTAL CONSEQUENTIAL INDIRECT SPECIAL OR PUNITIVE DAMAGES OF ANY KIND OR FOR LOSS OF REVENUE LOSS OF BUSINESS OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE USE PERFORMANCE FAILURE OR INTERRUPTION OF ITS PRODUCTS EVEN IF SMC OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES SOME STATES DO
6. NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS WHICH MAY VARY FROM STATE TO STATE NOTHING IN THIS WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS SMC will provide warranty service for one year following discontinuance from the active SMC price list Under the limited lifetime warranty internal and external power supplies fans and cables are covered by a standard one year warranty from date of purchase SMC Networks Inc 6 Hughes Irvine CA 92618 COMPLIANCES FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures
7. products to be free from defects in workmanship and materials under normal use and service for the applicable warranty term All SMC products carry a standard 90 day limited warranty from the date of purchase from SMC or its Authorized Reseller SMC may at its own discretion repair or replace any product not operating as warranted with a similar or functionally equivalent product during the applicable warranty term SMC will endeavor to repair or replace any product returned under warranty within 30 days of receipt of the product The standard limited warranty can be upgraded to a Limited Lifetime warranty by registering new products within 30 days of purchase from SMC or its Authorized Reseller Registration can be accomplished via the enclosed product registration card or online via the SMC web site Failure to register will not affect the standard limited warranty The Limited Lifetime warranty covers a product during the Life of that Product which is defined as the period of time during which the product is an Active SMC product A product is considered to be Active while it is listed on the current SMC price list As new technologies emerge older technologies become obsolete and SMC will at its discretion replace an older product in its product line with one that incorporates these newer technologies At that point the obsolete product is discontinued and is no longer an Active SMC product A list of discontinued product
8. the ringer equivalence Numbers of all the devices does not exceed 5 COMPLIANCES EC Conformance Declaration Class B SMC contact for these products in Europe is SMC Networks Europe Edificio Conata II Calle Fructu s Gelabert 6 8 29 4 08970 Sant Joan Desp Barcelona Spain This information technology equipment complies with the requirements of the Low Voltage Directive 73 23 EEC and the EMC Directive 89 336 EEC and carries the CE Mark accordingly It conforms to the following specifications EMC EN55022 1988 CISPR 22 1995 Class B IEC 1000 4 2 4 kV CD 8 kV AD IEC 1000 4 3 1995 3 V m IEC 1000 4 4 1995 1 0 kV power line 0 5 KV signal line IEC 1000 4 6 1995 3 Vrms Industry Canada Class B This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference causing equipment standard entitled Digital Apparatus ICES 003 of the Department of Communications Cet appareil num rique respecte les limites de bruits radio lectriques applicables aux appareils num riques de Classe B prescrites dans la norme sur le mat riel brouilleur Appareils Num riques NMB 003 dict e par le minist re des Communications Japan VCCI Class B TORE HROUBRESSRESREMHMBA VCCI 0R ILBO lt CFIABAREMNRE CT TORE ZERKTCEAJ OIE EBMELTWETA OXiEI74oT5LUZavLSHBHEIGRHELC A SHS ESMEMS SS SHMOTCEMHVET ANY FRU ERAS GE o CIEL UMISU
9. 4 EZ Connect ADSL USB Modem ADSL USB Modem High speed Internet access over existing phone lines One RJ 11 ADSL port Delivers USB plug and play installation Supports full rate DMT connection 8 Mbps downstream Mbps upstream Supports econmical G lite connection 1 5 Mbps downstream 512 Kbps upstream Graphic interface for ADSL connection management 9999 SMC User Guide Networks SMC7003 USB EZ Connect ADSL USB Modem User Guide From SMC s EZ Connect line of feature rich SOHO solutions SMC Networks 6 Hughes Irvine CA 92618 April 2001 Phone 949 707 2400 Pub 150552 102 R02 Information furnished by SMC Networks Inc SMC is believed to be accurate and reliable However no responsibility is assumed by SMC for its use nor for any infringements of patents or other rights of third parties which may result from its use No license is granted by implication or otherwise under any patent or patent rights of SMC SMC reserves the right to change specifications at any time without notice Copyright 2001 by SMC Networks Inc 6 Hughes Irvine CA 92618 All rights reserved Printed in Taiwan Trademarks SMC is a registered trademark and EZ Connect ia a trademark of SMC Networks Inc Other product and company names are trademarks or registered trademarks of their respective holders LIMITED WARRANTY Limited Warranty Limited Warranty Statement SMC Networks Inc SMC warrants its
10. 45 224 2331 Australia 61 2 9416 0437 Fax 61 2 9416 0474 India 91 22 8204437 Fax 91 22 8204443 SMC Networks 6 Hughes Irvine CA 92618 Model Number SMC7003 USB Phone 949 707 2400 Publication Number 150552 102 E042001 R02
11. Auto Sul ALCTL14 CHAPTER 8 UNINSTALLING MODEM SOFTWARE You can remove the SMC EZ Connect ADSL USB Modem software drivers by performing the following steps Note The USB cable should not be unplugged until after the uninstall process has been completed For Windows 98 applications the cable must be unplugged immediately following Step 6 below 1 From your PC desktop click Start Programs SMC DSL Modem Uninstall A notification message will appear indicating that the setup process has begun 2 Click Remove in the DSL Modem Installer window 3 A message will be displayed asking you to confirm removal of the USB ADSL modem software click Yes 4 The Information window will be displayed reminding you not to unplug the USB cable until the uninstall process has been completed Click OK 5 A message will be displayed indicating the software is being removed 6 The Setup Complete window indicates successful completion of the uninstall process Click Finish 8 1 UNINSTALLING MODEM SOFTWARE Note The screen for Windows 2000 applications will not ask you to reboot the system Click Finish to complete the Uninstall process 7 Unplug the USB cable from the PC Note The USB cable must be unplugged before the system is rebooted For Windows 98 applications the cable must be unplugged immediately since the reboot process was initiated in Step 6 above 8 2 APPENDIX A TROUBLESHOOTING
12. ION The CD that comes with the package contains all the software drivers available for the EZ Connect ADSL USB Modem A RELEASE TXT file that describes the contents of the CD is in the root directory LAN WAN and ATM modem drivers are stored in separate subdirectories Select the driver you need for your system This modem is fully software upgradeable so that new features and updates may be added by simply loading a new version of the device driver onto your PC Any new or updated drivers can be downloaded from SMC s Web site at http www smc com The modem drivers that can be used under specific Windows operating systems are shown on page 3 4 Installation procedures are described in text files on the driver disk However installation and configuration is described in more detail in this manual Protocol and Device Driver Selection ADSL modems employ ATM Asynchronous Transfer Mode framing ATM is a protocol that divides packets into small fixed sized cells for rapid transmission over high speed networks The ATM protocol allows various types of traffic e g data voice and video to be securely and efficiently carried over the same network ATM is being widely deployed by telecommunications carriers in their backbone networks Two types of ATM connections are possible PVC Permanent Virtual Circuit and SVC Switch Virtual Circuit The EZ Connect ADSL USB Modem currently only supports the PVC connections types through WAN LAN a
13. Moopiryinc TCP IP NETWORKING OPTIONS 3 From the Networking tab of the SMC Dial Up PPP Connection Properties window select Internet Protocol TCP IP and click Properties 4 15 Moopiryinc TCP IP NETWORKING OPTIONS 4 The Internet Protocol TCP IP Properties window is used to modify the IP address and DNS Server addresses internet Protocol TCP IP Properties ude General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically r Use the following IP address IP address 192 100 100 54 C Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server x 3 i Altemate DNS server E Suus ee Cancel e You can change the IP address to a user defined address by selecting Use the following IP address click inside the circle to the left of it and typing the address in the space provided e You can change the DNS Server addresses to user defined addresses by selecting Use the following DNS server addresses click inside the circle to the left of it and typing the addresses in the spaces provided Note The Advanced button of the Internet Protocol TCP IP Properties window may be used to alter DNS address WINS address
14. RU ILC REUS ix COMPLIANCES Australia AS NZS 3548 1995 Class B ACN 069 351 613 SMC contact for products in Australia is SMC Communications Pty Ltd Suite 18 12 Tryon Road Lindfield NSW2070 Phone 61 2 94160437 Fax 61 2 94160474 TABLE OF CONTENTS Introduction iui 4449444464549 ET 4045084 1 1 Key B at ufes 2 Oxo dA edat t i st ee Sahar ray one 1 2 Hardware Installation 2 1 Package Contents soccer USER IRAM ES 2 1 Description of Hardware 0 0 0 0 eee ee 2 2 LED FUNCHONS niana eee ee RR ARR Axa 2 3 Power Requirements eee 2 3 System Requirements lee eee eee 2 3 Connect the System liess 2 5 Phone Line Configuration eee 2 5 Driver Installation eee 3 1 Protocol and Device Driver Selection sls 3 1 Prerequisite Information eA 3 4 Running the Setup Program 1 2 0 ee eese 3 5 Installing the Modem eee 3 7 Modifying TCP IP Networking Options 4 1 WAN USB Driver itezddamdewne4 epe eur RE a 4 1 Microsoft Windows 98 First and Second Editions 4 1 Microsoft Windows 2000 0 00000 cece eee 4 4 LAN USB Divet errre Sra ecg So ee ee QR v DRE 4 6 Microsoft Windows 98 First and Second Editions 4 6 Microsoft Windows 2000 0 0 0 eee eee 4 9 ATM USB Driver cineca cts oy op oF Lone late Re RS 4 11 Microsoft Windows 98 Second Edition 4 11 Microsoft W
15. WARE INSTALLATION LED Functions The EZ Connect ADSL USB Modem contains two LEDs on the top panel one is marked Data and the other Power The operational status of the modem is indicated by the LED conditions listed below LED Status Description Data Flashing Indicates the modem is synchronizing its Green ADSL ATM link with the head end On Indicates an ADSL ATM link has been Green established on the RJ 11 port Power On Power is being supplied to the modem via the Green USB bus Power Requirements USB devices can be either self powered or bus powered A device which has no power connector is bus powered and derives its operating power from the USB connection directly The EZ Connect ADSL USB Modem is bus powered all you need to do is plug it into a host PC or self powered USB hub System Requirements The EZ Connect ADSL USB Modem requires the following PC features to operate e lt A host PC that supports the Universal Serial Bus 32 MB of RAM and 10 MB of hard disk space Windows 98 98 SE or 2000 with installation files ready Standard telephone cable with RJ 11 plugs HARDWARE INSTALLATION Note that to share Internet access on your network you will need to install appropriate Internet sharing software on one PC The ADSL network must meet the following minimum requirements ADSL service from your local telephone company or have access to an ADSL DSLAM Digital Subscri
16. al Up Networking X Properties Mooiryinc TCP IP NETWORKING OPTIONS Note The icon name may differ from that specified above The SMC connection icon will be identified as DSLWanUsb Line0 in the Device Name column when details are viewed from the Dial Up Networking window View Details 4 From the Server Types tab of the SMC Dial Up PPP Connection window select TCP IP marked with a check in the box to the left and click TCP IP Settings SMC Dial Up PPP Connection 4 2 Mopriryinc TCP IP NETWORKING OPTIONS The TCP IP Settings window is used to modify the IP address Name Server addresses and or default gateway TCP IP Settings KIESA We SEG Tf rine MITT e You can change the IP address to a user defined address by selecting Specify an IP address click inside the circle to the left of it and typing the address in the space provided e You can change the Name Server addresses to user defined addresses by selecting Specify name server addresses click inside the circle to the left of it and typing the addresses in the spaces provided e Change the default gateway by leaving the box blank to the left of Use default gateway on remote network Click OK The SMC Dial Up PPP Connection window will be redisplayed Click OK to close the window 4 3 Moopiryinc TCP IP NETWORKING OPTIONS Microsoft Windows 2000 TCP IP settings are automatically set up during
17. and IP security settings 5 Click OK from the Internet Protocol TCP IP Properties window 6 The SMC Dial Up PPP Connection Properties window will reappear Click OK to close the window 4 16 CHAPTER 5 CUSTOMIZING COMMUNICATION SETTINGS Once the SMC EZ Connect ADSL USB Modem and software have been installed the communication settings may be easily updated by performing the following steps 1 From your PC desktop click Start Programs SMC DSL Modem Configure A notification message will appear indicating that the setup process has begun Click Settings from the DSL Modem Installer window The Communication Settings window will be displayed Make the necessary changes to the VPI VCI Encapsulation type and or Modulation type and click Apply The Setup Complete window indicates successful completion of the customization process Select the Yes I want to restart my computer now option remove any disks from their drives and click Finish Your PC will reboot 5 1 CUSTOMIZING COMMUNICATION SETTINGS 5 2 CHAPTER 6 UPDATING THE MODEM SOFTWARE Once the EZ Connect ADSL USB Modem has been installed updating to a new version of the software is a simple process as detailed below 1 From your PC desktop click Start Programs SMC DSL Modem Configure A notification message will appear indicating that the setup process has begun Click Update from the DSL Modem I
18. ber Line Access Multiplexer PC configured with fixed IP address or dynamic IP address assignment via DHCP Gateway server address and DNS server address from your telephone company or network administrator You also need to get the prerequisite information listed on page 3 4 from your telephone company or network administrator HARDWARE INSTALLATION Connect the System Phone Line Configuration The EZ Connect ADSL USB Modem supports dual mode operation for both full rate G dmt and economical G lite Your service provider will therefore attach the outside ADSL line to a data phone splitter You can then connect your phones and computer directly to the splitter as shown below Plain Old Telephone System POTS Residential Connection Point NID Splitter F SMC7003 USB Data L Rr Depending on the wiring configuration used in your house separate wall jacks may be used for telephone and voice signals Otherwise you will need to connect your phones and PC directly to the splitter 1 Connect the modem s ADSL port to the data port on the splitter or to an RJ 11 telephone wall jack connected to this port using standard telephone cable 2 Insert the USB cable s Type B plug square end into the modem s USB port 3 Install the driver 2 5 HARDWARE INSTALLATION 4 Install the driver best suited for your connection needs as described in the next chapter 2 6 CHAPTER DRIVER INSTALLAT
19. check the contents of the box to be sure you ve received the following components EZ Connect ADSL USB Modem SMC7003 USB 1 USB cable modem to computer Type B to Type A 1 CD ROM with manual and drivers inside 1 registration card please complete and return to SMC Immediately inform your dealer in the event of any incorrect missing or damaged parts If possible please retain the carton and original packing materials in case there is a need to return the product Please fill out and return the Warranty Registration Card to SMC or register on SMC s Web site The EZ Connect ADSL USB Modem is covered by limited lifetime warranty 2 1 HARDWARE INSTALLATION Description of Hardware Setting up the EZ Connect ADSL USB Modem involves connecting the device s cables and installing the driver software Note that Windows 98 98 SE or 2000 should already be installed on the computer before installing the driver software The following figure shows the components of this modem SMC EZ Connect ADSL USB Modem SMC7003 USB Sa Power Data a a e USB Port RJ 11 Port ra Type B i ADSL a c Figure 2 1 EZ Connect ADSL USB Modem Power LED Green Data LED Green HARD
20. con and click Properties Ele Edt View Go Favoites Connections Help 1 3 m ad 8X m m amp j ui x 3 Back Forward Up Create Dial Cut Copy Paste Undo Delete Address Dial Up Networking x E Hose Nov SMC Dial Up Dia l U p onnection Networking SMC Dial Up PPP Connection PPP ATM Adapter Properties Device name DSLWanUsb Line0 To establish a dial up connection to this network Note The icon name may differ from that specified above The SMC connection icon will be identified as DSLAtmUsb Line0 in the Device Name column when details are viewed from the Dial Up Networking window View Details 4 11 Moopiryvinc TCP IP NETWORKING OPTIONS 4 From the Server Types tab of the SMC Dial Up PPP Connection window select TCP IP marked with a check in the box to the left and click TCP IP Settings SMC Dial Up PPP Connection 4 12 Mopriryinc TCP IP NETWORKING OPTIONS 5 The TCP IP Settings window is used to modify the IP address Name Server addresses and or default gateway TCP IP Settings tinier aly ey seconden Was e You can change the IP address to a user defined address by selecting Specify an IP address click inside the circle to the left of iD and typing the address in the space provided e You can change the Name Server addresses to user defined addresses by selecting Specify name server addresses Cclick insid
21. dicates successful completion of the installation process Select the Yes I want to restart my computer now option remove any disks from their drives and click Finish Your PC will reboot Continue with the Modem Installation section arr DRIVER INSTALLATION Installing the Modem 3 8 Note For Windows 98 SE applications you may need the Windows 98 SE source files to complete the installation Microsoft Windows has an auto detect feature known as Plug and Play that is capable of identifying when new hardware has been installed After you run the setup program reboot your PC and then connect the EZ Connect ADSL USB Modem to your PC 1 Insert the rectangular end of a USB cable into the USB port of your PC and the square end of the cable into the USB port of the USB modem It will be detected automatically and messages will be displayed as the modem software is installed 2 For Windows 2000 applications the Digital Signature Not Found window may appear warning that the installation software is not a digitally signed version A digital signature is not necessary SMC has tested the software with Windows 2000 Click Yes to allow the installation to continue We will be releasing a digitally signed version of the driver in the near future 3 For Windows 2000 applications the Found New Hardware Wizard window indicates the modem has been installed and suggests you reboot the system to have new settings take
22. e the circle to the left of it and typing the addresses in the spaces provided e Youcanchange the default gateway by leaving the box blank to the left of Use default gateway on remote network Click OK 6 The SMC Dial Up PPP Connection window will be redisplayed Click OK to close the window 4 13 Moopiryinc TCP IP NETWORKING OPTIONS Microsoft Windows 2000 4 14 TCP IP settings are automatically set up during the software installation process The following procedure may be used to change TCP IP settings if necessary 1 From your PC desktop right click the My Network Places icon and select Properties From the Network and Dial Up Connections window right click on the SMC Dial Up PPP Connection icon and click Properties 2 Dial Up Networking o xi Eie Edit View Go Favorites Connections Help e g amp uix Back Forward Up Create Dial Cut Copy Paste Undo Delete Address EA DialUp Networking O 5 li Make New D i a l U p Connection Networking SMC Dial Up PPP Connection PPP ATM Adapter Properties Device name DSLWanUsb Line0 To establish a dial up connection to this network Note The icon name may differ from that specified above The SMC connection icon will be identified as DSLAtmUsb Line0 in the Device Name column when details are viewed from the Network and Dial Up Connections window View Details
23. er makes the modem appear as a LAN or Ethernet device Connection establishment is automatic This driver supports Multiprotocol Encapsulation over ATM RFC 1483 with PVC connections DRIVER INSTALLATION e ATM driver this driver works in conjunction with the ATM services provided by Windows Call establishment is also performed through Windows Dial Up Networking This driver supports PPP RFC 2364 with PVC or SVC connections The device drivers are summarized in the table below Driver Type Protocols Windows OS WAN RFC 2364 Windows 98 Windows 98 SE Windows 2000 LAN RFC 1483 Windows 98 Windows 98 SE Windows 2000 ATM RFC1577 Windows 98 SE RFC 2364 Windows 2000 Windows Dial up Networking and Dial up ATM Support should be installed in your operating system prior to installing these drivers DRIVER INSTALLATION Prerequisite Information 3 4 The following information may be required depending on the driver you install Contact your DSL service provider before proceeding with software installation IP Address Settings the software installation process allows the server to dynamically assign IP Address settings If your application requires a static setting for specific address information you will need to know the following IP Address Subnet Mask for Bridged Ethernet applications only Default Gateway for Bridged Ethernet applications only Name Server Information the mode
24. ice traffic leaving your premises into a single stream Key Features 1 2 e High speed Internet access over existing phone lines e Full rate DMT connection 8 Mbps downstream 1 Mbps upstream and economical G lite connection 1 5 Mbps downstream 512 Kbps upstream e Multiprotocol encapsulation of all network protocols including TCP IP Novell s IPX and Windows NetBEUI for complete access to the Internet and corporate resources e Always on digital connection eliminates dial up delays and transparent reconnection when initiating any network request e Concurrent data and voice over a single connection needs splitter for both G dmt and G lite e Interoperable with Alcatel Cisco and other DSLAM central office equipment manufacturers e Compatible with various ISP services using RFC 1483 static IP assignment or PPP dynamic IP assignment e Graphic interface for ADSL connection management INTRODUCTION e Supports Windows 98 Windows 98 Second Edition and Windows 2000 e Delivers USB plug and play installation and configuration 1 3 INTRODUCTION CHAPTER 2 HARDWARE INSTALLATION Before installing the SMC ADSL USB Modem verify that you have all the items listed under Package Contents If any of the items are missing or damaged contact your local SMC distributor Also be sure you have all the necessary cabling before installing the modem Package Contents After unpacking the EZ Connect ADSL USB Modem
25. ified as DSLLanUsb LineO in the Device Name column when details are viewed from the Network and Dial Up Connection window View Details 3 Select Internet Protocol TCP IP from the General tab of the Local Area Connection window Click Properties Local Area Connection 2 Properties 21 x General Sharing Connect using E9 SMC USB ADSL LAN Modem Components checked are used by this connection a Client for Microsoft Networks sl File and Printer Sharing for Microsoft Networks Internet Protocol TCP IP KI K Install Uninstall Properties Description Transmission Control Protocol Intemet Protocol The default wide atea network protocol that provides communication across diverse interconnected networks Show icon in taskbar when connected 4 9 Moopiryinc TCP IP NETWORKING OPTIONS 4 The Internet Protocol TCP IP Properties window is used to modify the IP addresses and DNS Server addresses Internet Protocol TCP IP Properties ee 2d xj General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings C Obtain an IP address automatically r Use the following IP address IP address 182 100 100 59 Subnet mask 255 255 255 0 Default gateway 192 100 100 15 Obtain DNS addres
26. indows 2000 0 0 0 0 00 eee eee 4 14 Customizing Communication Settings 5 1 Updating the Modem Software 6 1 Control Panel Application 7 1 Physical Link Status Tab lees 7 2 TABLE OF CONTENTS ii System Information Tab 2 1 0 00 ee 7 3 Configuration Tab iiie 7 4 Uninstalling Modem Software 8 1 Troubleshooting A 1 You Cannot Connect to the Network 00 0 A 1 You Cannot Connect to the Internet 0 A 1 Specifications coi eRRRSRLERRR BER RR BERE B 1 ADSL Specifications sc cc ene ne eee ea ee e ede B 1 Physical Characteristics xod on eU ee bead B 2 Ordering Information es C 1 CHAPTER 1 INTRODUCTION The EZ Connect ADSL USB Modem provides high speed Internet access over existing phone lines by making use of previously unused frequency bandwidth above the voice band By placing ADSL signals above the frequency of the voice signal ADSL service can coexist on the same line with your telephone service ADSL is asymmetric in that it provides a higher data rate in the downstream receive direction than in the upstream transmit direction Asymmetric operation is ideal for typical home and small office use where files and information are downloaded more frequently than uploaded The EZ Connect ADSL USB Modem supports both full rate Discrete Multi Tone G dmt connection T1 413 Is
27. ipment must also be installed using an acceptable method of connection The customer should be aware that compliance with the above conditions might not prevent degradation of service in some situations Repairs to certified equipment should be coordinated by a representative designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Caution Users should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician as appropriate An explanatory note on Ringer Equivalence Numbers see Section 10 0 and their use must be provided for the terminal equipment user in the information accompanying the terminal equipment A notice similar to the following would be suitable NOTICE The Ringer Equivalence Number REN assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of
28. ission Convergence ATM Framing with traffic shaping ATM SAR AAL5 ATM Forum UNI3 1 signalling ATM UBR Service Class ADSL Service Service Type Full rate Discrete Multi Tone ADSL G dmt and Splitterless ADSL G _lite Data Rate G dmt 8 Mbps downstream 1 Mbps upstream G lite 1 5 Mbps downstream 512 Kbps upstream Media Type Simultaneous data voice can coexist with HPNA Service Provider Digital Subscriber Line Access Multiplexer DSLAM B 1 SPECIFICATIONS Media Connection USB cable connection to PC 90 ohm shielded USB cable max length 5m 16 ft RJ 11 phone wire connection to ADSL provider PC Requirements Host Interface USB Specification 1 1 or up System Requirements A PC and Windows 98 98 Second Edition or 2000 operating system Physical Characteristics B 2 Ports Upstream 1 USB Type B USB spec 1 1 differential and bi directional 12 Mbps high speed device Downstream RJ 11 Phone wire connection to ADSL service provider LEDs Power Data Dimensions 13 0 x 13 0 x 29 cm 5 12 x 5 12 x 1 14 in Weight 5 29 oz 150 g Input Power 5VDC 500mA maximum bus powered from USB host controller or hub Power Consumption 2 50 Watts maximum from USB host SPECIFICATIONS Temperature Operating 32 to 104 F 0 to 40 C Storage 40 to 160 F 40 to 70 C Humidity 5 to 95 non condensing Compliances CE Mark Emissions FCC Class B VCCI Class B Industry Canada Clas
29. l double click the SMC DSL Modem icon or just double click the SMC globe icon in the system tray Note To access the modem Control Panel the driver must be running Also make sure the USB cable is plugged into the modem 7 1 CONTROL PANEL APPLICATION Physical Link Status Tab 7 2 The Physical Link Status tab of the SMC DSL Modem window Control Panel allows you to review the current state of the EZ Connect ADSL USB Modem and connection When the green indicator is on in the Link Status field it indicates that a connection has been made This indicator blinks while a connection is being established The Transmitting and Receiving data activity are shown separately by individual flashing yellow indicators 5 SHC DSL Modem CONTROL PANEL APPLICATION System Information Tab The System Information tab displays the release number of the EZ Connect ADSL USB Modem driver the firmware release number and the control panel version that you are currently using SMC DSL Modem 7 3 CONTROL PANEL APPLICATION Configuration Tab 7 4 The Configuration tab offers driver appropriate Modulation Encapsulation and VPI and VCI values If you are using a WAN or ATM driver only the Modulation type will be displayed and may be modified For LAN driver applications you will be able to view and modify the Modulation type Encapsulation type and VPI and VCI values SMC DSL Modem 171 413
30. lity Otherwise you need to ask your network administrator for the appropriate IP settings C Obtain an IP address automatically s Use the following IP address IP address 182 100 100 53 Obtain DNS server address automatically Preferred DNS server r i Altemate DNS server 3 Advanced Use the following DNS server addresses Cancel e You can change the IP address to a user defined address by selecting Use tbe following IP address Cclick inside the circle to the left of it and typing the address in the space provided e You can change the DNS Server addresses to user defined addresses by selecting Use tbe following DNS server addresses click inside the circle to the left of it and typing the addresses in the spaces provided Note The Advanced button of the Internet Protocol TCP IP Properties window may be used to alter DNS addresses WINS addresses and IP security settings 5 Click OK from the Internet Protocol TCP IP Properties window 6 The SMC Dial Up PPP Connection Properties window will reappear Click OK to close the window 4 5 Moopiryinc TCP IP NETWORKING OPTIONS LAN USB Driver Microsoft Windows 98 First and Second Editions 4 6 TCP IP settings are automatically set up during the software installation process The following procedure may be used to change TCP IP settings if necessary 1 From the Control Panel window Start Setting
31. m software installation process allows the server to dynamically assign Name Server Address settings If your application requires a static setting for specific address information you will need to know the following Primary DNS Address Secondary DNS Address Primary WINS Address Secondary WINS Address Mode for LAN applications only Virtual Path ID VPD Virtual Circuit ID VCD Encapsulation type Modulation type User Name for PPP applications only Password for PPP applications only DRIVER INSTALLATION These items are only required if you are not using default values 3 5 DRIVER INSTALLATION Running the Setup Program Note Please view the README TXT file on the CD for product related information Start up your PC with the modem disconnected After Windows starts insert the CD ROM that comes with the EZ Connect ADSL USB Modem in your CD drive and click Setup exe to start the installation procedure The Welcome window provides an opportunity to quit the setup process to exit all Windows programs before continuing If the Windows programs were previously closed click Next The Start Copying Files window displays the default driver settings To automatically select the default settings click Next and continue to Step 7 To change the driver settings click Customize and continue to step 5 Start Copying Files xi Setup has enough information to start copying the driver file
32. nd ATM 3 1 DRIVER INSTALLATION drivers Several different protocols are used on top of ATM The protocol required in your configuration depends on the equipment deployed by your DSL service provider There are several possibilities Point to Point Protocol PPP Over ATM RFC 2364 PPP provides session setup user authentication login and encapsulation for upper layer protocols such as IP Internet ProtocoD The use of PPP makes the modem appear as a dial up modem to the operating system Dial Up Networking under Windows is used to establish a connection PPP is supported by the WAN Wide Area Network driver and ATM driver Bridged Routed Ethernet IP over ATM RFC 1483 This protocol makes the modem appear as a local area network LAN device to the operating system Classical IP and ARP over ATM RFC 1577 This protocol also makes the modem appear as a local area network LAN device to the operating system It supports IP address and ATM address mapping Three types of device drivers are provided for the EZ Connect ADSL USB Modem WAN ATM and LAN Note that all three drivers support the ATM protocol The proper choice of driver depends on your combination of Windows operating system and protocol WAN driver this driver causes the modem to resemble a dial up modem Call establishment is performed through Windows Dial Up Networking This driver supports PPP RFC 2364 with PVC connections LAN driver this driv
33. nstaller window A message will be displayed asking you to confirm the update click Yes The Select installation location window will be displayed Indicate the location of the Setup files and click OK Since updating the modem software requires removing the old version and installing a new one a message will be displayed informing you not to unplug the USB modem cable until the uninstall process has been completed Click OK A message will be displayed indicating the software is being uninstalled The Setup Complete window indicates successful completion of this portion of the updating process Click Finish 6 1 UPDATING THE MODEM SOFTWARE 8 Processing will continue with Step 2 of Running the Setup Program Please turn to page 3 6 Step 2 to complete the installation portion of the updating process CHAPTER 7 CONTROL PANEL APPLICATION The EZ Connect ADSL USB Modem control panel program provides a quick and easy way to configure and check the performance of the modem and the ADSL connection When open the monitor window updates every 2 seconds Note The following screen shots of the modem Control Panel are preliminary and are not final as the Control Panel functionality is continually being upgraded and improved Updated screen shots of the finished Control Panel will be available in revised versions of this manual through SMC From the Control Panel window Start Settings Control Pane
34. s Control Panel double click on the Network icon 2 Select TCP IP gt SMC ADSL USB LAN Modem from the Configuration tab of the Network window Click Properties Network 21 x Configuration Identification Access Control The following network components are installed E Client for Microsoft Networks Intel 21143 2 based 10 100 mbps Ethernet Controller Jj SMC USB ADSL LAN Modem TCP IP gt Intel 21143 2 based 10 100 mbps Ethernet Co Y TCP IP gt SMC USB ADSL LAN Modem Add Remove Properties Primary Network Logon Client for Microsoft Networks Eile and Print Sharing Description TCP IP is the protocol you use to connect to the Internet and wide area networks Cancel Mopiryinc TCP IP NETWORKING OPTIONS From the IP Address tab of the TCP IP Properties window select either the Obtain an IP address Automatically or Specify an IP Address option depending on your network setup If you select Specify an IP address type the IP Address and Subnet Mask in the spaces provided Consult with your network administrator to determine which option best suits your individual needs TCP IP Properties 192 100 100 59 4 7 Moopiryinc TCP IP NETWORKING OPTIONS 4 The Gateway tab allows you to add or remove gateways Consult with your network administrator to determine the appropriate addresses for your individual needs TCP IP Properties
35. s If you want to review or change any settings click Back or Customize If you are satisfied with the settings click Next to begin copying files Current Settings Service Provider Other Service Provider Driver type WAN Annex type VPI 0 ICI 88 Layer 3 Protocol RFC 2354 PPPoATM NULL Encapsulatio Modulation Multimode amp uto modulation Yes MaxUsbBandwidth 100 DRIVER INSTALLATION 5 Specify the driver type and click Next Then specify the VPI Virtual Path VCI Virtual Channel Layer 3 Encapsulation type and Modulation type and click Next Check with your service provider for the correct settings Select Driver Type x Select the type of driver that will be installed This choice depends on the service provider you are using ANNEX A ATM Driver ANNEX A LAN Driver Enter your communication settings below These settings are supplied by your service provider VPI fo VCI fee Encapsulation RFC 2364 PPPaATM NULL Encapsulation x REC 2364 PPPoATM LLC Encapsulation REC 2364 PPPa amp TM NULL Encapsulation Modulation Multimode z I Auto Modulation sect Ree 6 The Start Copying Files window will be redisplayed You may review the current settings and click Customize or Back to change the settings Click Next to accept the current settings a message will be displayed indicating that files are being copied 7 The Setup Complete window in
36. s B EN55022 CISPR 22 Class B C Tick AS NZS 3548 1995 Class B Immunity IEC 1000 4 2 3 4 6 Safety UL 1950 EN60950 TV CSA 22 2 No 950 Warranty Limited Lifetime B 3 SPECIFICATIONS B 4 APPENDIX C ORDERING INFORMATION EZ Connect ADSL Products and Accessories SMC7003 USB ADSL USB Modem C 1 ORDERING INFORMATION C 2 FOR TECHNICAL SUPPORT CALL From U S A and Canada 24 hours 7 days a week 800 SMC 4 YOU 949 707 2400 949 707 2460 Fax From Europe 8 00 AM 5 30 PM UK Greenwich Mean Time 44 0 1188 748740 44 0 1189 748741 Fax INTERNET E mail addresses techsupport smc com european techsupport smc europe com Driver updates http www smc com support html World Wide Web http www smc com FTP Site ftp smc com FOR LITERATURE OR ADVERTISING RESPONSE CALL U S A and Canada 800 SMC 4 YOU Fax 949 707 2460 Spain 34 93 477 4920 Fax 34 93 477 3774 UK 44 0 1188 748700 Fax 44 0 1189 748701 Southern Europe 33 1 41 18 68 68 Fax 33 1 41 18 68 69 Central Eastern Europe 49 0 89 92861 200 Fax 49 0 89 92861 230 Nordic 46 8 564 33145 Fax 46 8 87 62 62 Middle East 971 48818410 Fax 971 48817993 South Africa 27 0 11 3936491 Fax 27 0 11 3936491 PRC 86 10 6235 4958 Fax 86 10 6235 4962 Taiwan 886 2 2747 4780 Fax 886 2 2747 9220 Asia Pacific 65 238 6556 Fax 65 238 6466 Korea 82 2 553 0860 Fax 82 2 553 7202 Japan 81 45 224 2332 Fax 81
37. s automatically r Use the following DNS server addresses Preferred DNS server 7 1 Altemate DNS server s Advanced Cancel e You can change the IP address to a user defined address by selecting Use the following IP address option click inside the circle to the left of it and typing the addresses in the spaces provided e You can change the DNS Server addresses to user defined addresses by selecting Use the following DNS server addresses click inside the circle to the left of it and typing the addresses in the spaces provided Note The Advanced button of the Internet Protocol TCP IP Properties window may be used to alter IP settings DNS server addresses WINS addresses IP security options and TCP IP filtering options 5 Click OK from the Internet Protocol TCP IP Properties window 6 The SMC Local Area Connection Properties window will reappear Click OK to close the window 4 10 Mopiryinc TCP IP NETWORKING OPTIONS ATM USB Driver Microsoft Windows 98 Second Edition TCP IP settings are automatically set up during the software installation process The following procedure may be used to change TCP IP settings if necessary 1 From your PC desktop double click the My Computer icon 2 From the My Computer window double click the Dial Up Networking icon 3 From the Dial Up Networking window right click on the SMC ADSL Connection i
38. s with their respective dates of discontinuance can be found at http www smc com smc pages html support html All products that are replaced become the property of SMC Replacement products may be either new or reconditioned Any replaced or repaired product carries either a 30 day limited warranty or the remainder of the initial warranty whichever is longer SMC is not responsible for any custom software or firmware configuration information or memory data of Customer contained in stored on or integrated with any products returned to SMC pursuant to any warranty Products returned to SMC should have any customer installed accessory or add on components such as expansion modules removed prior to returning the product for replacement SMC is not responsible for these items if they are returned with the product Customers must contact SMC for a Return Material Authorization number prior to returning any product to SMC Proof of purchase may be required Any product returned to SMC without a valid Return Material Authorization RMA number clearly marked on the outside of the package will be returned to customer at customer s expense For warranty claims within North America please call our toll free customer support number at 800 762 4968 Customers are responsible for all shipping charges from their facility to SMC SMC is responsible for return shipping charges from SMC to customer WARRANTIES EXCLUSIVE IF AN SMC PRODUCT DOES NOT OPERATE
39. sue ID and the more economical G lite connection G 992 2 This modem delivers concurrent data and voice over a single connection It also supports a Rate Adaptive algorithm to maintain high data integrity under existing conditions including varied connection lengths and degraded signal quality And because all data is encapsulated in ATM frames the EZ Connect ADSL USB Modem can be connected directly to any standards compliant DSL Access Multiplexer DSLAM at your service provider s central office data is then sent through an ATM backbone and out to the Internet via an ISP router Moreover there s no need to install any new lines This plug in ADSL modem provides an always on digital connection that eliminates dial up delays and transparent reconnection when initiating any network request Full support for the ATM protocol also provides access to a wide range of advanced transport features including support for real time video 1 1 INTRODUCTION and other multimedia services requiring guaranteed Quality of Service QoS This device enables true telecommuting for the first time by providing complete access to Internet and corporate resources via multiprotocol encapsulation including TCP IP Novell s IPX and Windows NetBEUI network protocols Note Since this modem supports both G dmt and G_lite it requires an external splitter to separate the traffic entering your premises into data and voice and also to merge the data and vo
40. the software installation process The following procedure may be used to change TCP IP settings if necessary 1 From your PC desktop right click the My Network Places icon and select Properties 2 From the Network and Dial Up Connections window right click on the SMC Dial Up PPP Connection icon and click Properties Note The icon name may differ from that specified above The SMC connection icon will be identified as DSLWanUsb LineO in the Device Name column when details are viewed from the Network and Dial Up Connections window View Details 3 From the Networking tab of the SMC Dial UP PPP Connection Properties window select Internet Protocol TCP IP and click Properties SMC Dial Up PPP Connection Properties x General Options Security Networking Sharing Type of dial up server am calling PP 8 Client for Microsoft Networks Install Uninstall Raia Description Transmission Control Protocol Internet Protocol The default wide area network protocol that provides communication across diverse interconnected networks tee 4 4 Moopiryinc TCP IP NETWORKING OPTIONS 4 The Internet Protocol TCP IP Properties window is used to modify the IP address and DNS Server addresses Internet Protocol TCP IP Properties Ec E 2 x General You can get IP settings assigned automatically if your network supports this capabi
41. uivalence number c The USOC jack required d The FCC Registration number vii COMPLIANCES viii Items b and d are indicated on the label The Ringer Equivalence Number REN is used to determine how many devices can be connected to your telephone line In most areas the sum of the REN of all the devices on any one line should not exceed 5 0 If too many devices are attached they may not ring properly Industry Canada Required Information EQUIPMENT ATTACHMENTS LIMITATIONS To ensure that certified equipment is attached correctly and only to the networks of participating carriers the following statement shall accompany each unit of certified equipment offered for sale This statement must be included conspicuously in written or electronic format at or near the front of each copy of the operating manual or accompany other technical information or be included as a separate sheet The required statement is NOTICE The Industry Canada label identifies certified equipment This certification means that the equipment meets telecommunications network protective operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements documents s The department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equ
Download Pdf Manuals
Related Search