Fujitsu Siemens Celsius 442 (LKN:FKR-547515
Contents
1. SYSTEM BOARD D1327 SYSTEM BOARD D1327 TECHNICAL MANUAL TECHNICAL MANUAL co FUJITSU COMPUTERS SIEMENS Sie haben technische Fragen oder Probleme Wenden Sie sich bitte an _ Ihren zust ndigen Vertriebspartner e Verkaufsstelle Weitere Informationen finden Sie im Handbuch Sicherheit Garantie und Ergonomie Aktuelle Informationen zu unseren Produkten Tipps Updates usw finden Sie im Internet http www fujitsu siemens com Are there any technical problems or other questions you need clarified Please contact your sales partner e your sales outlet You will find further information in the manual Safety Guarantee and Ergonomics The latest information on our products tips updates etc can be found on the Internet under http www fujitsu siemens com Dieses Handbuch wurde auf Recycling Papier gedruckt This manual has been printed on recycled paper Ce manuel est imprim sur du papier recycle Este manual ha sido impreso sobre papel reciclado Questo manuale amp stato stampato su carta da riciclaggio Denna handbok r tryckt p recyclingpapper Dit handboek werd op recycling papier gedrukt Herausgegeben von Published by Fujitsu Siemens Computers GmbH Bestell Nr Order No A26361 D1327 Z120 1 7419 Printed in the Federal Republic of Germany AG 0801 08 01 26361 01327 2120 1 7419 Systembaugruppe D1327 System Board D1327 Technisches Handbuch Technica2. Intel chipset 845 Intel 82562EM LAN controller 10 100 Mbit s with RJ45 interface WOL with Magic Packet is supported as is booting from LAN with Bootix LAN BootP or Intel PXE Analogue Devices AD1885 AC 97 Audio Codec internal Stereo CD In Stereo AUX In external Mono Micro In Stereo Line In Game Midi port Stereo Line out headphones Fujitsu Siemens system monitoring and temperature monitoring 3 DIMM slots for 32 MB to 3 GB main memory SDRAM memory modules meet the PC133 specification with ECC Flash BIOS Power on functions RTC Wake on LAN on PCI Cards Wake on USB wake up support standby Energy saving functions APM and ACPI requires an operating system that supports ACPI Switching on off standby mode suspend mode via on off switch Switching on off via software Security functions Processor serial number Cover monitoring cover monitoring reports when the cover has been opened without authorisation System Setup and Keyboard password parallel and serial ports can be deactivated Floppy disk write protection via BIOS Setup Boot hard disk virus warning function A Flash BIOS and 5 on the memory modules virus protection function 6 PCI slots PCI slots support 3 3 V main and auxiliary voltages 26361 01327 2120 1 7419 English 3 Features 1 slot The AGP slot supports 1x 2x and 4x AG
3. care when you insert or remove boards Take great care to ensure that extension boards are slotted in straight without damaging components or conductors on the system board or any other components for example EMI spring contacts Be especially careful with the locking mechanisms catches centring pins etc when you replace the system board or components on it for example memory modules or processors Never use sharp objects screwdrivers for leverage Boards with electrostatic sensitive devices ESD are identifiable by the label shown When you handle boards fitted with ESDs you must under all circumstances observe the following points e You must always discharge static build up e g by touching a grounded object before working The equipment and tools you use must be free of static charges e Remove the power plug from the mains supply before inserting or removing boards containing ESDs e A Always hold boards with ESDs by their edges Nevertouch pins or conductors on boards fitted with ESDs 2 English 26361 01327 2120 1 7419 Features Features The components and connectors marked are not necessarily present on the system board System board in ATX format mPGA478 Intel processor Pentium 4 with 400 MHz Front Side Pentium 4 processors support MMX technology and Intel Streaming SIMD Extensions The size and frequency of first level cache and second level cache are dependent upon the processor used
4. even of parts are reserved Offenders will be liable for damages All rights including rights created by patent grant or registration of a utility model or design are reserved Delivery subject to availability Right of technical modification reserved This manual was produced by cognitas Gesellschaft f r Technik Dokumentation mbH www cognitas de Contents Introduction een INotatiaralebmyentibIis Important notes Information about boards E 35 MM HE cnt fee C Internal ports and connectors Temperature System monitoring E Hard disk COMMECHON eive rina eite gen RAW 25222 51 235421214241814 41 4442 211254212122220 111 24444 224 0122 02220142 86 14 12 PCI bus Settings with switches and jumpers Recovering System BIOS switch 2 Add on medules saisine anean EEG Installing and removing processors Upgrading main memory sia 55 Installing network board With WOL 2 reri nosti ei ether eius Replachngithellithium batlely Elore Tn 26361 01327 2120 1 7419 Introduct
5. P mode Only AGP boards with 1 5 V are supported DE hard disk controller connected to PCI bus for up to four IDE drives e g IDE hard disk drives ATAPI CD ROM drives The IDE hard disk controller are ATA33 66 100 ultra DMA capable and support PIO modes 0 4 e Floppy disk drive controller possible formats 720 KB 1 44 MB 2 88 MB The system board supports booting from a 120 MB IDE floppy disk drive Real time clock calendar with integrated battery backup e 1 internal WOL interface e 2internal USB ports C D 1external parallel port ECP and EPP compatible e 2external serial ports 160550 compatible with FIFO 2external PS 2 ports for keyboard and mouse e 2external USB ports A B External ports 1 2 PS 2 mouse port 8 Game Midi port 2 PS 2 keyboard port 9a Audio Line Out 3 Serial port 1 Headphones 4 Parallel port 9b Audio Line In 5 Serial port 2 9c Audio Micro In 6 LAN connector 7 USB ports A and B The components and connectors marked are not necessarily present on the system board 4 English 26361 01327 2120 1 7419 Features Internal ports and connectors 0000000000 eooooooooo DIMM 3 E DIMM 2 DIMM 1 1 Pow
6. cture LAN LSA MCH MMX P64H Interconnect PXE RAM Analogue Converter Access Memory RTC Real Time Clock SB Soundblaster SDRAM Synchronous Dynamic Random Access Memory RDRAM SGRAM Synchronous Graphic Random Access Memory Ee FF o SIMD Streaming Mode Instruction Single Instruction Multiple Data System Management Bus SVGA pose Super Video Graphic Adapter USB Universal Serial Bus Video Graphic Adapter Wake On LAN English 15
7. d components without first opening the device How to dismantle and reassemble the device is described in the Operating Manual accompanying the device Please observe the safety information provided in the Important notes chapter in the device s operating manual Incorrect replacement of the lithium battery may lead to a risk of explosion It is therefore essential to observe the instructions in the Add on modules Replacing the lithium battery section 26361 01327 2120 1 7419 English 1 Important notes The shipped version of this board complies with the requirements of the directive 89 336 EEC Electromagnetic compatibility Compliance was tested in a typical PC configuration When installing the board refer to the specific installation information in the Operating Manual or Technical Manual for the receiving device Connecting cables for peripherals must be adequately shielded to avoid interference Components can become very hot during operation Ensure you do not touch components when making extensions to the system board There is a danger of burns replacement of system expansions Information on which system expansions you can i The warranty is invalidated if the device is damaged during the installation or use is available from your sales outlet or the customer service centre Information about boards To prevent damage to the system board or the components and conductors on it please take great
8. er supply ATX 10 Cover monitoring 2 Floppy Disk Drive 11 USB ports C D 1 3 IDE drives and 4 secondary 12 USB ports C D2 4 Power supply monitoring 13 WOL 5 Connector for control panel and 14 CD audio input loudspeaker 15 AUX audio input 6 IDE drives 1 and 2 primary 16 Power supply 12 V 7 Voltage indicator LED 17 Fan 1 e g for the processor 8 2 Fan2 9 Fan3 The components and connectors marked are not necessarily present on the system board If both connectors are present on the system board only one connector can be used 26361 01327 2120 1 7419 English 5 Features Temperature System monitoring Temperature and system monitoring aim to reliably protect the computer hardware against damage caused by overheating In addition any unnecessary noise is also prevented by reducing the fan speed and information is provided about the system status Cover monitoring protects the system from unauthorised opening An onboard controller developed by Fujitsu Siemens Computers controls the temperature and system monitoring The following functions are supported Temperature monitoring Measurement of the processor and the system temperature with an onboard temperature sensor Temperature control The temperature is controlled by adjusting the fan speed and or by reducing the clock frequency of the processor The clock frequency of the processor is dependent upon the setting in the BIOS Setup Tempe
9. icator LED will glow if this is the case PCI slots support 3 3 V main and auxiliary voltages AGP boards support 1 5 V main and auxiliary voltages 0000000000 0000000000 DIMM _ DIMM 2 DIMM 1 pL 2 1 Socket for processor with heat sink 5 Lithium battery 2 Location bank 1 for main memory 6 PClslots 1 2 3 4 5 6 3 Location bank 2 for main memory 7 AGP slot 4 Location bank 3 for main memory 10 English 26361 01327 2120 1 7419 Add on modules Installing and removing processors gt Pull the lever in the direction of the arrow 1 and lift it as far as it will go 2 gt Remove the old processor from the socket 3 gt Insert the new processor in the socket so that the angled corner of the processor matches the coding on the socket A with regard to the position 4 The angled corner of the processor may be covered by the heat sink In this case let yourself be guided by the marking in the rows of pins on the underside of the processor gt Push the lever back down until it clicks into place 5 26361 01327 2120 1 7419 English 11 Add on modules Upgrading main memory These slots are suitable for DIMM format 32 64 128 256 512 1024 MB SDRAM memory modules Mem
10. ion Depending on the configuration chosen some of the hardware components described may not be available on your system board You will find further information in the BIOS Setup description Further information about drivers is provided in the readme files on the hard disk on the supplied drivers diskettes on the Drivers amp Utilities or on the ServerStart CD Notational conventions The meanings of the symbols and fonts used in this manual are as follows Pay particular attention to text marked with this symbol Failure to observe this warning endangers your life destroys the device or may lead to loss of data i Supplementary information remarks and tips follow this symbol Text which follows this symbol describes activities that must be performed in the order shown This symbol indicates that you must enter a blank space press the Space Bar at this point dj This symbol indicates that you must press the Enter key Text in this typeface indicates screen outputs Text in this bold typefaceindicates the entries you make via the keyboard Text in italics indicates commands or menu items Quotation marks indicate names of chapters or terms Important notes Store this manual close to the device If you pass the device on to third parties you should pass this manual on with it Be sure to read this page carefully and note the information before you open the device You cannot access the system boar
11. l Manual Ausgabe August 2001 August 2001 edition Intel Pentium und Celeron sind eingetragene der Intel Corporation USA Microsoft MS MS DOS und Windows sind eingetragene Warenzeichen der Microsoft Corporation PS 2 und OS 2 Warp sind eingetragene Warenzeichen von International Business Machines Inc Alle weiteren genannten Warenzeichen sind Warenzeichen oder eingetragene Warenzeichen der jeweiligen Inhaber und werden als gesch tzt anerkannt Copyright Fujitsu Siemens Computers GmbH 2001 Alle Rechte vorbehalten insbesondere auch auszugsweise die der bersetzung des Nachdrucks der Wiedergabe durch Kopieren oder hnliche Verfahren Zuwiderhandlungen verpflichten zu Schadenersatz Alle Rechte vorbehalten insbesondere f r den Fall der Patenterteilung oder GM Eintragung Lieferm glichkeiten und technische nderungen vorbehalten Dieses Handbuch wurde erstellt von cognitas Gesellschaft f r Technik Dokumentation mbH www cognitas de Intel Pentium and Celeron are registered trademarks of Intel Corporation USA Microsoft MS MS DOS and Windows are registered trademarks of Microsoft Corporation PS 2 and OS 2 Warp are registered trademarks of International Business Machines Inc All other trademarks referenced are trademarks or registered trademarks of their respective owners whose protected rights are acknowledged All rights including rights of translation reproduction by printing copying or similar methods
12. ory modules with different memory capacities can be combined You may only use unbuffered 3 3 V memory modules Buffered memory modules are not supported SDRAM memory modules must meet the PC133 specification Installing a memory module gt Push the holders on each side of the memory compartment outwards gt Insert the memory module into the location 1 gt Atthe same time flip the lateral holders upwards until the memory module snaps in place 2 Removing a memory module gt Push the clips on the right and left of the compartment outward 1 gt Carefully remove the memory module from the compartment 2 12 English 26361 01327 2120 1 7419 Add on modules Installing network board with WOL gt Install the network board as described in the operating manual for your unit gt Push the WOL cable onto the WOL plug connector of the system board il To use the WOL functionality of a network board the power supply must provide a 5 V auxiliary voltage of at least 1 A If the system board was not already incorporated in a device when you bought it you must check whether your power supply can provide the auxiliary voltage You may find further information in the supplied description of the network board 26361 01327 2120 1 7419 English 13 Add on modules Replacing the lithium battery Incorrect replacement of the lithium battery may lead to a risk of explosion The lithium battery must be replaced wi
13. rature dependent processor speed control enables a reduced fan speed decreasing noise Fan monitoring Fans which have been removed blocked or sticky fans are detected Blocked or sticky fans are operated with 12 V pulse voltage If the device has a monitored fan removed while the system is switched off this is indicated by the message LED when the system is switched on again and processed by the BIOS or the application Fan control With the exception of the auxiliary fan AUX the fans are regulated according to temperature Sensor monitoring The removal of or a fault in a temperature sensor is detected Should this happen all fans monitored by this sensor run at maximum speed to achieve the greatest possible protection of the hardware If the device has a monitored fan removed while the system is switched off this is indicated by the message LED when the system is switched on again and processed by the BIOS or the application Cover monitoring Unauthorised opening of the cover is detected even when the system is switched off However this will only be indicated when the system is switched on again 6 English 26361 01327 2120 1 7419 Features Voltage monitoring The voltages 12 V 5 V and the CMOS battery are monitored With hardware monitoring regardless of the operating system and processor the advantages compared to conventional software monitoring are clear suitable for all operating systems and proces
14. rrupts The following table shows which PCI bus interrupts are assigned on the system board PCI bus interrupt Component on system board PCI bus slot 1 PCI bus slot 2 PCI bus slot 3 PCI bus slot 4 PCI bus slot 5 PCI bus slot 6 CNR slot AGP slot First USB controller Second USB controller LAN controller SMBus AC 97 Audio 8 English 26361 01327 2120 1 7419 Settings with switches and jumpers Settings with switches and jumpers Switch 1 must always be set to off Switch 2 System BIOS recovery Switch 3 must always be set to off Switch 4 must always be set to off il The clock frequency of the processor is set automatically Recovering System BIOS switch 2 Switch 2 enables recovery of the old system BIOS after an attempt to update has failed To restore the old system BIOS you need a Flash BIOS Diskette please call our customer service centre On The System BIOS executes from floppy drive A and the inserted Flash BIOS Diskette restores the System BIOS on the system board of Normal operation default setting 26361 01327 2120 1 7419 English 9 Add on modules Add on modules Exit Suspend mode switch off the device and remove the power plug from the mains supply before carrying out any of the procedures described in this chapter Even when you have switched off the device parts e g memory modules AGP and PCI extension boards are still supplied with power The voltage ind
15. sor types additional load on processor performance optimum temperature protection even if process faults or faults are present in the operating system optimum noise reduction Three different operating modes are available and can be configured in BIOS Setup System Management Hard disk connection An ultra ATA 66 or ultra ATA 100 hard disk must be connected with a cable especially designed for the ultra ATA 66or ultra ATA 100 mode gt Connect the end of the cable marked with blue to the system board LAN connector This system board has an optional Intel 82550 LAN controller which supports transfer speeds of 10 Mbit s and 100 Mbit s The LAN controller is equipped with a 3 KB transmission and receiving buffer FIFO and supports WOL function through Magic Packet It is also possible to boot a device without its own boot hard disk via LAN Here Bootix LAN BootP and Intel PXE are supported Basic AOL II is also supported Basic AOL II helps to protect systems against theft or damage Basic AOL II can also inform the administrator about hardware faults and software errors The LAN RJ45 connector is equipped with a yellow and a green LED light emitting diode 1 Yellow indicator 2 Green indicator Yellow a connection exists e g to a hub Green Link Mode the LAN connection is active WOL mode a Magic Packet is being received 26361 01327 2120 1 7419 English 7 Features PCI bus inte
16. th an identical battery or a battery type recommended by the manufacturer CR2032 Do not throw lithium batteries into the household waste They must be disposed of in accordance with local regulations concerning special waste Ensure that you insert the battery the right way round The plus pole must be on the top The following graphic representation is also valid if the lithium battery is built in vertically gt Liftthe contact 1 a few millimetres and remove the battery from its socket 2 gt Inserta new lithium battery of the same type into the socket 3 14 English 26361 01327 2120 1 7419 Glossary Glossary The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations Not all technical terms and abbreviations listed here are valid for the described system board Power Management Interface ATA Advanced Technology Are Central Processing Unit Communication Network Riser C RIMM Continuity Rambus Inline Memory Module DIMM Dual Inline Memory Module Error Correcting Code Electrical Erasable Programmable Read Only Memory FirstinFirsOut FIFO First In First Out Front Side Bus GMCH Graphics and Memory Controller Hub Accelerator IAPC Instantly Available Power AC Managed Desktop PC Design ntelligent Drive Electronics IPSEC Internet Protocol Security 26361 01327 2120 1 7419 Industrial Standard Archite
Download Pdf Manuals
Related Search