IBM ThinkVision L170p 17" LCD Monitor
Contents
1. Remove the User s Guide and Installation Files CD from the computer CD ROM drive Installing the Windows 2000 device driver To manually install or update the device driver for the Microsoft Windows 2000 Professional operating system perform the following steps 1 2 Click Start gt Settings gt Control Panel and then double click Display In the Display Properties window click the Settings tab and then click Advanced Click the Monitor tab and then click Properties gt Driver gt Update Driver When the Update Device Driver Wizard window opens select Search for a suitable driver for my device and click Next gt Insert the User s Guide and Installation Files CD into the computer CD ROM drive type d change the drive letter to match your CD ROM drive if it is not drive D in the Copy manufacturer s files from box click Next and then Finish to complete the installation Close the Display Properties window Remove the User s Guide and Installation Files CD from the computer CD ROM drive Installing the Windows 98 device driver 10 Windows 98 automatically detects the new monitor and displays the Add New Hardware Wizard window if the device driver is not already installed 1 Insert the Device Driver and User s Guide CD into the computer CD ROM drive and click Next twice when the Add New Hardware Wizard window opens Click the CD ROM drive box to install the device drivers from the CD2. Microsoft Windows NT Windows Me or Windows XP Auto Setup for Windows 3 1 Windows 95 Windows 98 Windows NT Windows 2000 Windows Me or Windows XP on page 15 Before you begin Auto Setup for your computer 1 Make sure the computer s video mode is set in the range of the supported screen resolution shown in the Table on page 24 You should perform Auro SETUP for each screen mode you use 13 Auto Setup for DOS e If the monitor is in standby mode STANDBY ON it may automatically turn off while you are waiting for itto warm up If this happens switch off the monitor and switch it on again after a few seconds e f you are using PC DOS V Z change to U S mode by typing CHEV US and pressing ENTER at the command prompt e The size and diversity of the L dot pattern varies with the screen resolution 14 To set up the monitor automatically in DOS do the following 1 11 12 13 14 Turn on the monitor first then turn on the computer If the message CHECK SIGNAL CABLE is displayed or if nothing is displayed check that the video interface cable is connected properly the correct video adapter card is installed the correct supported display mode is selected for your computer Wait approximately 15 minutes until the monitor warms up Insert the User s Guide and Installation Files CD into the computer CD ROM drive Display the command prompt screen of the D
3. Mac 31 kHz 81 kHz Digital amp Analog 55 Hz 76 Hz Environment Temperature Operating Storage Shipping Humidity Operating Storage Shipping 10 to 35 C 50 to 95 F 20 to 60 C 4 to 140 F 20 to 60 C 4 to 1405 F 10 to 80 5 to 95 5 to 95 31 ENGLISH Service Information 32 The following parts are for use by IBM service or IBM authorized dealers to support the customer warranty Parts are for service use only 31P9584 31P9585 31P9587 31P9588 31P9590 31P9594 31P9595 Model Type 6734 6734 HBO 6734 HGO 6734 HBO 6734 HGO 6734 HBO 6734 HGO 6734 HBO 6734 HGO 6734 HBO 6734 HGO Monitor Stealth Black Monitor Ash Grey Stand Stealth Black Stand Ash Grey Analog Video Cable User s Guide CD Setup Guide ENGLISH Notices and Trademarks This section contains information on notices and trademarks Notices IBM may not offer the products services or features discussed in this document in all countries Consult your local IBM representative for information on the products and services currently available in your area Any reference to an IBM product program or service is not intended to state or imply that only that IBM product program or service may be used Any functionally equivalent product program or service that does not infringe any IBM intellectual property right may be used instead However it is the user s responsib
4. Windows XP ENTER 6 When the test pattern appears press the OSD Enter button gi at the bottom of the monitor to display the initial OSD menu 7 Use an Arrow button or gt to select the Image Setup icon KO and press the OSD Enter button gi to access the function 8 Using an Arrow button or gt select AUTOMATIC and press the OSD Enter button ga This activates the Auto SETUP procedure which will optimize the display settings with the provided test pattern 15 ENGLISH 16 The screen will dim blink on and off several times and you might notice small changes to the test pattern To abort the Auto Setup function press the Esc key 9 When finished the OSD main menu returns Press the Exit button gt once to exit from the OSD 10 Press the Esc key to return to Windows You have completed the monitor setup for Windows If you are using the DOS operating system go to Auto Setup for DOS on page 14 ENGLISH Manual Setup Normally you can complete the setup procedure using Auro SETUP however if your screen image is still distorted after you perform Auro SETUP or the Installation CD does not run on your system perform MANUAL SETUP c If the monitor is in standby 1 Have your monitor turned on for about 15 minutes until the monitor L mode STANDBY ON it warms up might automatically turn off while you are waiting for it to warm up N Display the image you most frequently us
5. C Exit Exits the OSD AUVE Left Arrow Moves the cursor to highlight icons Active and other options gt Right Arrow Moves the cursor to highlight icons Active and other options Enters menus and sub menus and e OSD Enter selects the highlighted option Aclive 18 e The image is already optimized for many display modes however the user controls can be used to adjust the image to your liking e The settings are saved after adjustment and when exiting the OSD and will be effective thereafter ENGLISH Operation Press the OSD Enter button to display the main OSD menu Usethe Arrow buttons to move among the icons Select an icon and press OSD Enter to access that function If there is a sub menu you can move between options using the Arrow buttons then press OSD Enter to select that function Use the Arrow buttons to make adjustments Press the ga button to save Press the Exit button to move backwards through the sub menus and exit from the OSD OSD Lock Unlock This feature allows you to secure the current control settings while allowing the user to adjust Brightness and Contrast so that they cannot be inadvertently changed You can unlock the OSD controls at any time by using the same procedure Push and hold the OSD Enter button for 10 seconds to Lock or to Unlock When locked a LOCKED message will be displayed 19 On screen display OSD controls e The LCD monitor n
6. Hx0 uses a 17 inch TFT LCD Dimensions A Lower Position Height 357 1 mm 14 05 in Depth 237 0 mm 9 33 in Width 344 8 mm 15 74 in B Higher Position Height 457 1 mm 17 99 in Depth 237 0 mm 9 33 in Width 399 8 mm 15 74 in Weight Unpackaged 5 8 Kg 12 78 Ib Packaged 7 1 Kg 15 65 Ib Tilt Swivel Lift Tilt 0 4 30 Swivel 135 135 Lift 100 mm stroke Image Viewable Image Size 432 7 mm 17 0 in Maximum Height 270 0 mm 10 6 in Maximum Width 338 0 mm 13 3 in Pixel Pitch 0 264 mm 010 in H x 0 264 mm 010 in V Power Input Supply Voltage 100 240 V ac 60 50 3 Hz Max Supply Current 1 5 A at 120 V ac Power Normal Operation 40W Consumption DPMS Stand by DPMS Suspend lt 2 VV for Analog lt 3 W for Digital lt 2 VV for Analog lt 3 W for Digital DPMS off 2 VV for Analog 3 VV for Digital Video Input Signal Analog Direct Drive 75 ohm 0 7 V Input Analog Horiz Addressability 1280 pixels max Vert Addressability 1024 lines max Clock Frequency 135 MHz Video Interface DVI Input Digital Input Signal VESA TMDS Panel Link TM Horiz Addressability Vert Addressability Clock Frequency 1280 pixels max 1024 lines max 135 MHz Communications VESA DDC 2B Supported Display Modes VESA Standard modes between Horiz Frequency Vert Frequency IBM VESA HP Sun
7. and then click Next Confirm that the device driver was found on the CD and click Next gt twice to install the device driver Click Finish to close the Add New Hardware Wizard window To manually install or update the device driver for the Microsoft Windows 98 operating system perform the following steps ENGLISH Click Start gt Settings gt Control Panel and then double click Display In the Display Properties window click the Settings tab and then click Advanced Click the Monitor tab and then click Change When the Update Device Driver Wizard window opens follow the steps in the previous paragraph Remove the User s Guide and Installation Files CD from the computer CD ROM drive Installing the Windows 95 device driver Right click the My Computer icon on the computer desktop and then select Properties gt System to view the version number listed in the System window Perform the steps below for the appropriate version If you have Windows 95 Version 4 00 9504 use the following steps to manually install or update the device driver 1 2 Click Start gt Settings gt Control Panel and then double click Display In the Display Properties window click the Settings tab and then click Change Display Type In the Change Display Type window click Change and then click Have Disk Insert the User s Guide and Installation Files CD into the computer CD ROM drive type d change the drive letter to matc
8. or right as well as lift up and down as shown below Working Practices Z This section gives Rest advice on how you can work comfortably and reduce Take regular breaks Vary your posture stand up and stretch occasionally as fatigue prolonged use of computer workstations can be tiring ENGLISH Back Sit back in your chair and use the backrest Hands Adjust the seat height so that your forearms are approximately horizontal and your wrists are straight when using the keyboard Your upper arms should be relaxed with your elbows near your body Use a light touch on the keyboard keeping your hands and fingers relaxed Allow a space in front of the keyboard to rest your wrists when not typing Consider using a wristpad Eyesight Working with monitors in common with any prolonged close work can be visually demanding Look away from the screen periodically and have your eyesight checked regularly Screen settings Set the screen brightness and contrast to a comfortable level You may have to adjust this as the lighting changes during the day Many application programs let you select color combinations which can help you to view in comfort See the User controls section on page 18 for more information Caring for your Monitor Be sure to turn off the power before you perform any maintenance on the monitor Clean your monitor as follows Gently wipe the device covers and the screen with a soft cloth Remove fin
9. over 3 900 000 thin film transistors TFTs A small number of missing discolored or lighted dots may be present on the screen which is an intrinsic characteristic of the TFT LCD technology and is not an LCD defect Further Help gt If possible stay by your 4 computer Your Technical Support Representative may vvish to go through the problem vvith you during the call More help late breaking 4 news and details ofthe latest accessories for these products may be found on the worldwide web at http www pc ibm com us accessories ENGLISH If you are unable to correct the problem yourself you may seek further help as follows Call the IBM HelpCenter In the US call 1 800 772 2227 In Canada Toronto Only call 416 383 3344 In Canada all others call 1 800 565 3344 In other countries contact your dealer retailer or other IBM authorized Servicer Before calling please have available as much of the following information as possible Model and serial number from the label on your monitor Purchase receipt Description of problem Computer type and model System configuration hardware fitted etc System BIOS version number Operating System and version number Display driver version number Video Adapter Type oaAaNoua rw M 29 opecifications gt Power consumption figures are Z for the monitor and the povver supply combined 30 This color monitor Type model 6734
10. that are appropriate to your problem Problem i Suggested Action Reference Remove the other graphics adapter plugged Computer does There is into one of the expansion Connecting not boot after another slot your Monitor the graphics graphics ifthe card is built in to for Analog adapter is adapter inthe the motherboard check section on installed computer your system manual for page 6 instructions on how to disable the built in adapter The screen image is garbled or The display Connecting unusable driver is trying your Monitor rolling screen to use a Select the correct for Analog images setting your monitor again s overlapping monitor does section on screen images not support page 6 or a blank screen Ensure that the electrical outlet and the monitor are both switched on Checkthat the power cord is firmly plugged into Connecting Screen is blank the electrical outlet andthe your Monitor and power No powerto power supply unit for Analog RM 8 monitor q indicator is off fthe power cord plug section on has a removable fuse page 6 replace it Try another power cord Try another electrical outlet Problem jointe Suggested Action Reference Screen is blank Brightness User and power and Contrast Adjust brightness and controls indicator is may be too contrast section on steady green low page 18 Press any key on the
11. the back of the graphics adapter See picture below graphics adapter DVI Signal Cable 6 Connect the power cord to the power port on the back of your monitor if the power cord supplied is not attached to the monitor Then insert the plug into a properly grounded electrical outlet 7 Use the cable holder a to neatly organize the video and power cables 8 Switch on the power source and your computer To turn on the monitor push and release the power switch To switch it off push and release the power switch again Switching on your Monitor 1 Switch on the power source and your computer 2 Switch on your monitor by pushing and releasing the power switch marked 0 To switch off your monitor push and release the power switch again 3 Turn on the monitor and then the computer 4 Run Auro Setup by following the instructions in the Device Driver Installation section on page 9 Device Driver Installation ENGLISH Use the User s Guide and Installation Files CDthat comes with your monitor to install the appropriate device driver for your operating system Installing the Windows XP device driver To manually install or update the device driver for the Microsoft Windows XP operating system perform the following steps 1 Insert the User s Guide and Installation Files CD into the computer CD ROM drive Click Start gt Control Panel gt Appearance 8 Themes and the
12. IBM ThinkVision 170p Monitor mE SS A MA m E puc mm er SN il a ay ae dr a AAA E mm ey RR A U SE AA Y L170p User s Guide English UU First Edition April 2003 Note For important information refer to the Monitor Safety and Warranty manual that comes with this monitor Contents Safety Read first ase nete vijat ia 55 Dod cae OC c ee Gi d e casar e an icta gt 2 Setting p the MO NOT cusa pee xv wal WERE RACER Fea WR RAO a 3 Product Description Se ea 3 Handling Instl gtlgns s ice s Pe ee NER iia 3 Workplace Preparation nee 4 Adjusting the Monitor Position een 4 Working Practices aie asta P 4 Caring tor your MONO gss ae sd ho tus Rink one a RR rs ee it 5 Connecting your Monitor for Analog lisse 6 Connecting your Monitor for Digital lt oooooeooooooommrnars 7 Switching on your Monitor sese Bee ee REA bide Pee aed et kee ya 8 Device Driver Installation 0 20s 9 WindowsXP ca vates fex rgo p Pee mE Y EX oni Pa peor Pob ana e Selene 9 Windows Millennium IIR eee 9 Windows 2000 shnet A A RETRO RR RRS e D A DUOC RARE RE 10 Windows 98 uoce xin Dues he RD ae RR CAR gba Aus E LASS A wade eed 10 WindOoWS 95 aua sce Recette Rly toe ob pb Nah s nat et p Sok ed leo us din 11 Auto Setup Analog Only i i aa aaa aa aa aa aaa eee 13 Auto Setup sd iz kd E A anit ye yt is dece tum Deas dk dt sh 13 Au
13. OS full screen display Type d change the drive letter to match your CD ROM drive if it is not drive D Type TESTPATD and press ENTER Select from the screen the number for the color or text mode you want to set up Select from the screen the number for the video mode you want to set up You can repeat this process for as many of the color and video modes as you need When the dot pattern appears press the OSD Enter button y at the bottom of the monitor to display the initial OSD menu Use an Arrow button or gt to select the Image Setup icon GO then press the OSD Enter y button to access the function Using an Arrow button or gt select AUTOMATIC and press the OSD Enter button ga This activates the Auto SETUP procedure which will optimize the display settings with the provided dot patterns The screen will flash off several times and you might notice small changes to the test pattern When finished the OSD main menu returns Press the Exit button gt to exit from the OSD Press the ESCAPE key to exit the test pattern program Type Exit at the command prompt to return to Windows If you use other operating systems perform the appropriate Auto Setup for those systems using instructions given in Auto Setup for Windows 3 1 Windows 95 Windows 98 Windows NT Windows 2000 Windows Me or Windows XP on page 15 Auto Setup for Windows 3 1 Windows 95 Windows 98 Windows NT Windows 2000 Window
14. The monitor is keyboard or move the Power mouse to restore in the Power operation Management Management P l section on Checkthe P Standby state EU COE page 25 Management software on your computer Check that the signal Connecting Screen is Blank The monitoris Cable s firmly connectedto your Monitor alia pows not receiving puet i for Analog indicator is a video signal Checkthat no pins are ti steady amber i i SEAN bent in the signal cable page 6 connector Press any key on the The monitoris keyboard or move the Power in the Power mouse to restore Man ment Management operation S DER S Suspend or Checkthe Power page 25 Off state Management software on your computer Screen is blank Display mode and power of the Besit i Further indicator is computer is KG NE Information Flashing green outside the Mb N a d section on every 0 5 range of the supported display mode page 23 second monitor Thereare Select Image Setup User Image appears noises in the menu in the OSD Then controls to be smeared ideo signal select MANUAL to adjust section on Phase Clock settings page 18 User Image appears The Color t 9 pp setting may Adjust the Color conirols discolored be incorrect settings sector On page 18 27 ENGLISH 28 Problem Possible Cause Suggested Action Reference A few dots are missing discolored or inappropriately lighted TheLCD contains
15. ay need to re attach the CRT monitor temporarily until you have re configured the computer preferably to 1280 x 1024 at 60Hz Product Disposal ENGLISH To benefit from power management the monitor must be used in conjunction with a computer that implements the Video Electronics Standards Association VESA Display Power Management Signalling DPMS Standard The power management feature is invoked when the computer recognizes that you have not used your mouse or keyboard for a user definable period There are several states as described in the table below As an ENERGY STAR Partner IBM has determined that this product meets the ENERGY STAR guidelines for energy efficiency For optimal performance switch off your monitor at the end of each working day or whenever you expect to leave it unused for long periods during the day Power Restoring am Indicator Screen Operation Compliance On Blinking green Normal Active off Blinking green Blank Press a key or E STAR T9 move the mouse ENERGY STAR There may be a slight delay before the picture reappears The fluorescent lamp in the liquid crystal display contains a small amount of mercury Dispose of it as required by local ordinances and regulations 25 Troubleshooting If you have a problem setting up or using your monitor you might be able to solve it yourself Before calling your retailer or IBM try the suggested actions
16. d blue Controls Locked E Color Image Properties 1 Preset Mode 6500K 6500K adjusts the screen more red 7200K 7200K adjusts the screen to the default color settings 9300K 9300K adjusts the screen more blue 2 Custom Red Increases or decreases red Green Increases or decreases green Blue Increases or decreases blue This monitor can accept video 1 selects D SUB Same as Analog 1 x 2 signals through two different Analog Input video signal connectors Most desktop computers use a D SUB connector Select Digital among OSD controls when you use DVI connector 2 selects DVI Digital Options Shows resolution refresh rate and product details Note This screen does not allow any changes to the settings Information The language chosen affects Select one of the 5 only the language of the OSD languages English It has no effect on any French Italian German Language software running on the and Spanish to use for computer the OSD Same as Analog 21 ENGLISH OSD Icon on Main Menu Continued Submenu Description Controls and Adjustments Analog Controls and Adjustments Digital Options Menu Position 1 Default 2 Custom Horizontal Vertical Adjusts menu location on the screen Returns the menu position to the default settings Changes the horizontal position of OSD Changes the vert
17. e on the screen 3 Press the OSD Enter button atthe bottom of the monitor to display the initial OSD menu 4 Use an Arrow button or gt to select the Image Setup icon KO and press the OSD Enter button gi to access the function 5 Using an Arrow button or gt select MANUAL press gi and then press gt once to select Clock Left and right arrow adjustment indicators become illuminated see page 21 6 Use the Arrow buttons to manually adjust to correct as much as possible for noise in the video signal then press gt to save the changes 7 Use an Arrow button to select Phase and press the qi button 8 Use the Arrow buttons again to tune the image to your liking To save press the gi button two times 9 When finished press the Exit button 4 two times to exit from the OSD You have completed the monitor setup 17 Adjusting Your LCD Monitor User controls ThinkVision User control features Direct access controls Icon Control Description OSD 1942 Input Change Switches the video input source Inactive X Image Setup Activates automatic image adjustment Inactive wv Directly accesses to Brightness on the E je Brightness OSD man ment Inactive qi OSD Enter Displays the OSD main menu Inactive o Power Switch Switches the monitor on and off Main OSD menu controls Icon Control Description OSD Exits from menus and sub menus
18. eeds t time to become thermally The settings adjustable with the user controls are viewed through the On Screen Display OSD Press the OSD Enter button ga to activate the OSD stable the first time you turn it on each day Thus to achieve more accurate adjustments for parameters allow the LCD monitor to warm up be On for at least 15 minutes before making any screen adjustments Initial appearance of OSD OW G9 B gt OSD functions OSD Icon on Submenu Description Controls and Controls and Main Menu P Adjustments Analog Adjustments Digital xk xx Au du Adjusts brightness Same as Analog Brightness Brightness d Contrast Adjusts contrast lo 9 Controls Locked Contrast S O Image Position O Horizontal Position Moves the screen left or right Controls Locked O Vertical Position Moves the screen up or down S gt s gt Controls Locked 20 OSD Icon on Submenu Description Controls and Controls and Main Menu P Adjustments Analog Adjustments Digital Activates automatic image adjustment KO KO Controls Locked Image Setup Automatic 0 Use the or button to adjust away the interference If satisfactory results are not obtained using the Phase Manual adjustment use the Clock adjustment and then use Phase e Clock again Phase Adjusts intensity of red green an
19. eplace or modify the display driver The Auto Setup instructions require the monitor to be warmed up for 15 minutes This is not required for normal operation By pressing the LV key you will have direct access to the Image Setup control that is used during the Auto Setup process e The AUTO SETUP process only applies to the current screen mode When a new mode is selected repeat this section to reset the monitor When you first use your monitor you must perform Auto Setup This procedure sets up your monitor to process the video signals from your computer without image discoloration or smearing After you perform Auto Setup the settings are stored and used each time you turn on the monitor To optimise the displayed image a set up utility is provided on the CD Operation of the utility is dependent on the operating system on your computer For correct operation locate the operating system on your computer from the table below and follow the appropriate instructions You can choose to run Auro Setup for each operating system that you use This means that if you sometimes use your monitor while running any version of Windows and sometimes also use it from within DOS not a DOS window you must run Auro SETUP for both Windows and DOS You can run versions of AUTO SETUP in any order Operating System Corresponding Auto Setup procedure DOS Auto Setup for DOS on page 14 Windows 3 1 Windows 95 Windows 98 Windows 2000
20. ger marks and grease with a damp cloth and mild detergent do not use solvents or abrasives Never use flammable cleaning material to clean your IBM monitor or any other electrical apparatus Connecting your Monitor for Analog Be sure to read the Safety 1 Turn off your computer and all attached devices Information at the front of this User Guide before 2 Connect the signal cable to the video port on the back of your computer carrying out this procedure This port might be directly attached to your computer figure A or it might be part of a video adapter card figure B The video port on your computer or video adapter card might be blue to match the blue connector on your monitor s video cable 3 Connect the power cord to the power port on the back of your monitor if the power cord supplied is not attached to the monitor Then insert the plug into a properly grounded electrical outlet ENGLISH Connecting your Monitor for Digital 1 Purchase an industry standard DVI D cable from your local computer supply store 2 Turn off your computer and all attached devices 3 Tilt monitor all the way forward 4 Connectthe DVI connector at the end of the signal cable to the DVI port located on the back of the Monitor See picture below Connecting DVI Cable DVI Cable 5 Connect the DVI connector at the other end of the signal cable to the DVI port located on
21. h your CD ROM drive if it is not drive D in the Copy manufacturer s files from box and click OK In the Select Device window click the appropriate monitor model and then click OK In the Change Display Type window click Close In the Display Properties window click OK Remove the User s Guide and Installation Files CD from the computer CD ROM drive If you have Windows 95 Version 4 00 950B use the following steps to manually install or update the device driver 1 2 Click Start gt Settings gt Control Panel and then double click Display In the Display Properties window click the Settings tab and then click Advanced Properties In the Advanced Display Properties window click the Monitor tab and then click Change 11 12 In the Select Device window click Have Disk Insert the User s Guide and Installation Files CD into the computer CD ROM drive type d change the drive letter to match your CD ROM drive if it is not drive D in the Copy manufacturer s files from box and click OK In the Select Device window click the appropriate monitor model and then click OK In the Advanced Display Properties window click Close In the Display Properties window click OK Remove the User s Guide and Installation Files CD from the computer CD ROM drive Auto Setup Analog Only ENGLISH Auto Setup The Setup Utility included on the setup diskette is for displaying dot patterns They do not r
22. ical position of OSD T s a y a Q Factory Reset Resets monitor to the origital settings Does not make the adjustment Resets the settings Cancel Reset ey Changes button repeat rate y s and menu time out setting QW Accessibility X Selects or button Off increases by 1 OJ repeating rate each time the button is Button repeat presser u P Default increases rate Menu time out Sets the length of time the OSD will remain active after the last time a button is pressed continuously while the button is pressed Slow increases by 1 every 2 seconds while the button is pressed Use the or gt button to select time from 5 to 60 seconds Same as Analog 22 Further Information ENGLISH Display modes The display mode the monitor uses is controlled by the computer Therefore refer to your computer documentation for details on how to change display modes The image size position and shape might change when the display mode changes This is normal and the image can be readjusted using AUTO SETUP and the monitor controls Unlike CRT monitors which require a high refresh rate to minimize flicker TFT technology is inherently flicker free If possible configure your computer for 1280 x 1024 addressability at 60Hz vertical refresh rate For the display modes listed on the next page the screen image has been op
23. ility to evaluate and verify the operation of any non IBM product program or service IBM may have patents or pending patent applications covering subject matter described in this document The furnishing of this document does not give you any license to these patents You can send license inquiries in writing to IBM Director of Licensing IBM Corporation North Castle Drive Armonk NY 10504 1785 U S A The following paragraph does not apply to the United Kingdom or any country where such provisions are inconsistent with local law INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Some states do not allow disclaimer of express or implied warranties in certain transactions therefore this statement may not apply to you This information could include technical inaccuracies or typographical errors Changes are periodically made to the information herein these changes will be incorporated in new editions of the publication IBM may make improvements and or changes in the product s and or the program s described in this publication at any time without notice IBM may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you Any references in this publication t
24. ith a computer with a suitable on board sub system or Video Adapter card that can support SXGA 1280 x 1024 XGA 1024 x 768 SVGA 800 x 600 or VGA 640 x 480 at 60 Hz In addition to your monitor your option package includes the followings User s Guide and Installation Files CD Monitor Warranty and Safety manual IBM ThinkVision L170p Monitor Setup Guide Power Cord AC Adapter IBM ThinkVision L170p Monitor Analog Interface Cable Attached to Monitor Handling Instructions Do not support the monitor 1 Liftthe monitor by placing your hands where indicated below within the screen area The Liquid Crystal Display is glass and can be damaged by rough handling or excessive pressure 2 Before using your monitor for the first time remove the clear protective film from the front of the screen Workplace Preparation y Thissectiongivesadviceon Height A what you should consider l before you set up your monitor Position the monitor so that the top of the screen is slightly below your eye level when you sit at your workstation Orientation Choose a position that gives the least reflection from lights and windows usually at a right angle to any windows Position the monitor directly in front of you so that you do not have to twist your body to use it Tilt the monitor to a comfortable viewing angle Adjusting the Monitor Position Viewing Angle You can tilt the screen backward and forward swivel left
25. n click the Display icon In the Display Properties window click the Settings tab and then click Advanced Click the Monitor tab and then click Properties gt Driver tab gt Update Driver When the Hardware Update Wizard window opens select Install the software automatically click Next gt and then Finish to complete the installation Close the Display Properties window Remove the User s Guide and Installation Files CD from the computer CD ROM drive Installing the Windows Me device driver To manually install or update the device driver for the Microsoft Windows Millennium Edition operating system perform the following steps 1 2 Click Start gt Settings gt Control Panel and then double click Display In the Display Properties window click the Settings tab and then click Advanced Click the Monitor tab and then click Change gt Specify the location of the driver gt Next When the Update Device Driver Wizard window opens select Display a list of all the drivers in a specific location so you can select the driver you want and click Next gt Insert the the User s Guide and Installation Files CD into the computer CD ROM drive then click Have Disk Type d change the drive letter to match your CD ROM drive if it is not drive D in the Copy manufacturer s files from box then click OK Click Next Next and then Finish to complete the installation Close the Display Properties window
26. o non IBM Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites The materials at those Web sites are not part of the materials for this IBM product and use of those Web sites is at your own risk 33 34 Trademarks The following terms used in this publication are trademarks or service marks of the IBM Corporation in the United States other countries or both HelpCenter IBM ENERGY STAR is a U S Govt registered trademark Microsoft Windows and Windows NT are trademarks of Microsoft Corporation in the United States other countries or both Other company product and service names may be trademarks or service marks of others Copyright International Business Machines Corporation 2003 All rights reserved
27. s Me or Windows XP e Ifthe monitor is in standby mode STANDBY ON it may automatically turn off while you are waiting for it to warm up e The size and diversity of the dot pattern varies with the screen resolution e Position the mouse pointer at the bottom center of the screen This allows AUTO SETUP to run properly To set up the monitor automatically in Windows 3 1 Windows 95 Windows 95 Windows 98 Windows NT Windows 2000 Windows Me or Windows XP do the following 1 Turn on the monitor first then the computer If the message CHECK SIGNAL CABLE is displayed or if nothing is displayed check that the video interface cable is connected properly the correct video adapter card is installed the correct supported display mode is selected for your computer 2 Wait approximately 15 minutes until the monitor warms up 3 Drag the icon bar and tool bar if they are displayed to the bottom of the screen 4 Insert the User s Guide and Installation Files CD into the computer CD ROM drive 5 Check the operating system installed on your computer and follow the instructions from the table below Operating system installation steps eme Step1 Step2 Step3 Step4 Windows 3 1 Open Select Select Type PROGRAM FILE RUN DATESTPAT Windows NT 3 5 MANAGER change the Windows 95 drive letter to match your CD Windows 98 up Windows 2000 Select Sar ROM drive if it Windows Me or and press
28. timized during manufacture 23 e For image problems you may want to run AUTO Setup again before consulting to this section In most cases AUTO SETUP can fix the problems See Auto Setup for DOS on page 14 for details 24 Factory Set Display Modes Addressability Refresh Rate EET Analog Digital 640 x 350 70 Hz 31 5 kHz Yes Yes 640 x 480 75Hz 37 5 kHz Yes Yes 640 x 480 72 HZ 37 8 kHz Yes Yes 640 x 480 66 Hz 35 0 kHz Yes Yes 640 x 480 60 Hz 31 5 kHz Yes Yes 720 x 400 70 Hz 31 4 kHz Yes Yes 800 x 600 56 Hz 35 1 kHz Yes Yes 800 x 600 60 Hz 37 8 kHz Yes Yes 800 x 600 72 Hz 48 0 kHz Yes Yes 800 x 600 75 Hz 46 8 kHz Yes Yes 832 x 624 75 Hz 49 7 kHz Yes Yes 1024 x 768 60 Hz 48 4 kHz Yes Yes 1024 x 768 70 Hz 56 5 kHz Yes Yes 1024 x 768 75 Hz 60 0 kHz Yes Yes 1280 x 10241 60 Hz 64 0 kHz Yes Yes 1280 x 1024 70 Hz 74 4 kHz Yes No 1280 x 1024 75 Hz 80 0 kHz Yes No 1280 x 1024 76 Hz 81 1 kHz Yes No 1152 x 864 75 Hz 67 5 kHz Yes Yes 1152 x 870 75Hz 68 7 kHz Yes No 1152 x 900 60 Hz 61 8 kHz Yes No T Recommended Note VESA timings are as detailed in the VESA Display Monitor Timing Specification Version 1 0 Revision 0 8 dated 09 17 98 Power Management e If your computer has Z previously been used vvith a CRT monitor andis currently configured to a display mode outside the range that the Flat Panel monitor can display you m
29. to Setup for DOS da SZ at d ra A AE d sd e Bek ee Rd 14 Auto Setup for Windows 3 1 Windows 95 Windows 98 Windows 2000 Windows NT Windows Me or Windows XD RR RR RR 15 Manual SE tup zu nane da Steg DT 17 Adjusting Your LCD Monitor dd si i esa nda i na e rr a a A 18 User Contios iae e RR RR Up a kr RU ACRIOR 18 On screen display OSD controls 0 ca essei new e RR Ron bins oe 20 Further Information s s ikia a a a RD XS De 23 Display modes sexi REI E eR IR AE ERREUR ede eq Y A US 23 Power Management ex zehn ys on Sols deae aC e Roe pes RR RAR R dod a 25 Prod ctiDISposallLs tod tan e edt ads At TT 25 Troubleshooting gt ndar ocu Bo enm dh REACTOR E cae aE A Roe e ce 26 Further Help 3553 us ose ee he ame oem lotes ae tds fuit eg a R ee ere 29 Specifications ui sente as cce nue yn rece nu ean ono n e E AR AR uU ORCI S 30 Service Information se ii dei Lev ga A Ea ia a 32 Notices and Trademarks ee ee ee ee eee hh nnns 33 ENGLISH E Safety Read first Before installing this product read the Safety Information Avant d installer ce produit lisez les consignes de s curit Vor der Installation dieses Produkts die Sicherheitshinweise lesen Mpv ykaraotrjoete To Tpoi v auto dia dote Tic nAnpopopie aopdxela safety information MMVI MRNA NR WIP AT 1NTD 172000 7197 A term k telep t se el tt olvassa el a Biztons gi el r sokat Prima di installare questo prodotto leggere le Informazioni s
30. ulla Sicurezza Antes de instalar este produto leia as Informa es de Seguran a L s s kerhetsinformationen innan du installerar den h r produkten Prije instalacije ovog produkta obavezno pro itajte Sigurnosne Upute Les sikkerhetsinformasjonen Safety Information f r du installerer dette produktet Przed zainstalowaniem tego produktu nale y zapozna si z ksi k Informacje dotycz ce bezpiecze stwa Safety Information Ilpez Za ce uicrampa OBO rpojrykr npoynrtajte HHPOPpMannjara 3a 6es6e rocr Pred in tal ciou tohto zariadenia si pe itaje Bezpe nosin predpisy Pred namestitvijo tega proizvoda preberite Varnostne informacije Ennen kuin asennat t m n tuotteen lue turvaohjeet kohdasta Safety Information P ed instalac tohoto produktu si prect te p ru ku bezpe nostn ch instrukc EERE mi WFAN Safety Information KEM KARAJ e ZA A X Ad cula bel j a Za Las sikkerhedsforskrifterne for du installerer dette produkt SiO REEOBU HERRE RRA L ESL USS AOI AA SA ABS SIedAS Ri aul Antes de instalar este producto lea la informacion de seguridad Antes de instalar este produto leia as Informa es de Seguran a llepen ycTaHoBKON nponykra npouruTe UHCTPYKUMM nO TexHuke 6eaonacHocTM Lees voordat u dit product installeert eerst de veiligheidsvoorschriften ENGLISH Setting up the monitor Product Description The IBM ThinkVision TFT LCD L170p Color Monitor works w
Download Pdf Manuals
Related Search