Home

Lucent Avaya X330W 2DS1 (700214612) Router

Contents

1. Certification Description FCC Part 68 USA Protection of telephone networks from harm caused by terminal equipment wiring CS03 Industry Canada Similar to FCC Part 68 TBR12 Europe Unstructured 2048 Kbps digital leased line terminal equipment requirements TBR13 Europe Structured 2048 Kbps digital leased line terminal equipment requirements JATE Japan Avaya X330W 2DS1 User s Guide VII Preface NEBS Compliance Standards The following table shows the X330WAN compliance with NEBS standards Certification Description NEBS level 3 USA Electrical and Physical How to Contact Us If you need additional help the following services are available You may need to purchase an extended service agreement to use some of these services Contact your Avaya representative for more information To contact Avaya s technical support please call e From the United States 1 800 237 0016 press 0 then press 73300 e From South America and Central amp Latin America CALA 1 727 217 2425 for Spanish e Outside North America 972 3 645 8458 For updated information visit http www avaya com support All trademarks registered trademarks service names product and or brand names are the sole property of their respective owners Copyright 2002 Avaya Inc All rights reserved VII Avaya X330W 2DS1 User s Guide Chapter 1 Overview Avaya presents the X3
2. module to the P330 switch 2 Grasp the two screw knob and pull gently but firmly towards yourself The X330WAN module is removed 3 Insert another WAN access router module or the blanking plate into the switch Avaya X330W 2DS1 User s Guide 17 Chapter 2 Installation 18 Avaya X330W 2DS1 User s Guide Chapter 3 Initial Configuration This chapter describes the initial configuration of the X330WAN and includes the following sections e Connecting the X330WAN Describes the cables used to connect the X330WAN e Configuring the X330WAN Describes how to configure an X330WAN Fast Ethernet T1 E1 interface or Loopback and which commands to use to check and save your configuration e X330WAN Default Settings Lists the default settings of the X330WAN Connecting the X330WAN This section describes the cables used to connect the X330WAN Connecting the E1 T1 Ports To connect a E1 T1 module to a network use an RJ 48C cable minimum 26 gauge to connect the E1 T1 port to an RJ 48C wall jack Connecting the Ethernet Port The X330WAN includes a 10 100Base T port Connect a UTP Category 5 cable with an RJ 45 connector to the 100Base TX port The maximum UTP cable length connected to the 10 100Base T port is 100 m 328 ft You can obtain appropriate cables from your local supplier Connecting the Console Port Each Avaya X330WAN module has one serial port on the front panel for connecting a termi
3. no ip rip authentication mode simple none simple none The authentication type used in RIP Version 2 packets D yp D e simple clear text authentication e none no authentication Example To specify simple authentication to be used in RIP Version 2 packets on the interface marketing X330WAN 2DS1 1 configure ip rip authentication mode simple Avaya X330W 2DS1 User s Guide 77 Chapter 7 X330WAN CLI Commands ip rip default route mode Interface context Use the ip rip default route mode command to enable learning of the default route received by the RIP protocol The default state is talk listen Using the X330WAN the no form of the command disables listening to default routes Note This command is executed from the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no ip rip default route mode lt mode gt The possible default route modes on an interface are talk listen Set RIP to send and receive default route updates on the interface talk only Set RIP to send but not receive default route updates on the interface Example X330WAN 2DS1 1 configure ip rip default route mode talk only ip rip poison reverse Interface Context Use the ip rip poison reverse command to enable split horizon with poison reverse on an interface The no form of this command disables the poison reverse mechanism The split horizon technique pre
4. For detailed information on CLI commands see Chapter 7 X330WAN CLI Commands Note After clearing the condition causing the LOF alarm the module will continue to indicate an LOF condition for approximately 10 seconds High Ber Major Definition High threshold Bit Error Rating This alarm is the result of an average error rate of 1 bit per 1000 for 10 seconds The alarm severity is Major Indication The alarm is indicated using the show controllers command from the CLI For more information refer to Monitoring Traffic on page 33 Corrective Actions e Check the integrity of the physical E1 T1 line e If regenerators are used check the integrity of the regenerators e Use loopbacks to help pinpoint the cause of the alarm condition For information on using loopbacks refer to Using Loopbacks on page 36 Note After clearing the condition causing the High BER Major alarm the module will continue to indicate an High BER Major condition for approximately 11 seconds RAI Yellow Definition Remote Alarm Indication Local Rx line is down There is a problem with the remote module The alarm severity is Major Indication The alarm is indicated when the ALM LED lights up or by using the show controllers command from the CLI For more information refer to Monitoring Traffic on page 33 Corrective Action e Check your configuration for example framing to verify that it matches the configuration of the rem
5. ew_archive file Embedded Web Manager archive file ip_address The IP address of the TFTP server Example X330WAN 2DS1 1 super copy tftp SW_image c p330 p330web101 EW_archive c p330 p330web201 192 168 49 10 dir Use the dir command to show the file types that have been downloaded to the device The syntax for this command is dir Output Example X330WAN 2DS1 1 super dir M file ver num file type file location file description startup config N A Startup Conf Nv Ram Startup Config running config N A Running Conf Ram Running Config X330WAN A N A SW Component Flash Bank A Software Image Bank A X330WAN B 3 9 5 SW RT Image Flash Bank B Software Image Bank B P3WAN N A SW Web Image Nv Ram EmWeb application Output Fields Field Description M The device number file There are several files loaded into the device s memory e module config file which contains the configuration settings made to this device e stack config file which contains the configuration settings made at the stack level for example IP address of the stack e EW Archive file which contains the Device Manager Embedded Web software 50 Avaya X330W 2DS1 User s Guide General Device Commands ver num S W Version number relevant only for the Device Management S W file type There are several file types e Running Conf the configuration currently in use and the startup configuration e SW Web Image Device Manager S W archive file file lo
6. ip access list dscp name lt policy list number gt lt dscp gt lt name gt policy list number An integer 100 199 or for the X330WAN 100 149 where 0 is the default list dscp DSCP entry 0 63 name Entry name 104 Avaya X330W 2DS1 User s Guide Policy CLI Commands Example X330WAN 2DS1 1 super ip access list dscp name 101 16 special ip access list dscp precedence Use the ip access list dsc precedence command to set a DSCP precedence Note This command is only supported by the P333R LB device and X330WAN module The syntax for this command is ip access list dscp precedence lt policy list number gt lt dscp gt lt precedence gt policy list number An integer 100 199 or for the X330WAN 100 149 where 0 is the default list dscp DSCP entry 0 63 precedence mandatory optional Example X330WAN 2DS1 1 super ip access list dscp precedence 101 16 mandatory ip access list dscp trust Use the ip access list dscp trust command to set a DSCP trust Note This command is only supported by the P333R LB device and X330WAN module The syntax for this command is ip access list dscp trust lt policy list number gt untrusted Avaya X330W 2DS1 User s Guide 105 Chapter 7 X330WAN CLI Commands trust cos trust dscp trust cos dscp policy list number An integer 100 199 or for the X330WAN 100 149 where 0 is the default list Example X
7. loopback local line payload line The controller loops the external line signal back toward the network without reframing the DS1 signal payload The controller loops the external line signal back toward the network and reframes the DS1 signal Example X330WAN 2DS1 1 config controller 1 loopback local line loopback remote Controller context Use the loopback remote command to ask the far end to put itself into loopback mode Note 1 This command can only be performed if the controller is set to T1 2 Use this command during line set up and maintenance Avaya X330W 2DS1 User s Guide 135 Chapter7 X330WAN CLI Commands loopback remote line payload line The controller loops the external line signal back toward the network without reframing the DS1 signal payload The controller loops the external line signal back toward the network and reframes the DS1 signal This option is available in the framing esf mode and only when fdl is defined Example X330WAN 2DS1 1 config controller 1 loopback remote line mtu Serial interface context Use the mtu command to set the interface Maximum Transmission Unit MTU Use the no form of this command to restore interface MTU to the default value 1500 The syntax for this command is no mtu lt size in bytes gt size in bytes Range from 64 1500 Example X330WAN 2DS1 1 config if Serial1l 1 mtu 1000 no channel group Controller context Us
8. Documentation and Online Help Refer to the Avaya P330 Documentation and Utilities CD Software Download You can perform software download using the CLI or Avaya UpdateMaster Avaya X330W 2DS1 User s Guide 43 Chapter 6 Embedded Web Manager 44 Avaya X330W 2DS1 User s Guide Chapter 7 X330W AN CLI Commands This chapter provides a complete list of all WAN related CLI commands Each command that appears on the list is accompanied by a detailed description including the proper syntax The list is presented in alphabetical order to help you locate commands easily Introduction About CLI The CLI is command line driven and does not have any menus To activate a configuration option type the desired command at the prompt and press Enter To exit a context type exit You can use all show commands in User mode To configure the X330WAN you must either be in Supervisor mode or enter the Configure context Generic commands are performed from the Configure context If you are in Supervisor mode or have entered the Configure context you can enter any of the following contexts e Controller e Interface Console e Interface Fast Ethernet e Interface Fabric Fast Ethernet e Interface Serial e Interface Loopback e Other contexts Layer 1 E1 T1 commands are performed from the Controller context and Layer 2 Layer 3 Fabric PPP commands are performed from the various Interface contexts For a list of all Controll
9. No active PPP session SIG Green Signal ON A signal is detected on the port OFF No signal is detected on the port Avaya X330W 2DS1 User s Guide 11 Chapter 1 Overview 12 Avaya X330W 2DS1 User s Guide Chapter 2 Installation This chapter describes the X330WAN installation procedure Safety Information A H Warning Installation and removal of the X330WAN must only be implemented by qualified personnel Caution Hold the X330WAN only by the edges to avoid damage from static electricity Do not touch the top or bottom of the circuit board If possible wear a wrist strap and use an anti static bag Device Support The X330WAN enables you to connect your Avaya P330 switch to a WAN The X330WAN can be inserted into switches of the Avaya P330 product line which include an expansion slot These include the following Avaya P330 family switches e Avaya P333T Embedded S W Ver 3 9 and higher e Avaya P334T Embedded S W Ver 3 9 and higher e Avaya P332MF Embedded S W Ver 3 9 and higher e Avaya P333R Embedded S W Ver 3 9 and higher e Avaya P333R LB Embedded S W Ver 3 9 and higher e Avaya P333T PWR Embedded S W Ver 3 9 and higher Before You Install The X330WAN can only be installed in the above Avaya switches using firmware ver 3 9 or higher If you need to upgrade the software obtain the latest version of the software from http www avaya com su
10. Packets that traverse the inband LAN or the Ethernet port This will be marked as the IEEE 802 1p tag in the packet only on the FabricFastEthernet interface Classification into one of the 4 transmit queues The Composite Operation Table contains pre defined entries for the basic policies that existed in the P333R These entries are created by the agent for each Access List and are Read Only Controlling Network Access to the X330WAN Using Policy lists you can control all traffic designated to and from the X330WAN s CPU including management and routing protocols traffic By activating Policy rules defined for a Loopback interface you can control all traffic entering leaving the CPU from to all X330WAN interfaces Rules governing traffic to the CPU can be defined at a single point regardless of the actual interface which the packet entered and the specific IP address being managed Note A Policy list activated on a Loopback interface does not apply to packets routed by the CPU Avaya X330W 2DS1 User s Guide Features Avaya X330WAN Network Management Comprehensive network management is a key component of today s networks Avaya provides multiple ways of managing the X330WAN to suit your needs Command Line Interface CLI The Avaya P330 CLI provides a terminal type configuration tool for local or remote configuration of X330WAN features and functions X330WAN configurations are saved in the format of CLI
11. The CLI responds with the following Entering the Modem mode will occur automatically upon proprietary modem cable plug in into the console port The terminal mode would be restarted automatically upon insertion of proprietary terminal cable Use the DB 25 to RJ 45 connector to plug the console cable to the modem s DB 25 connector Plug the other end of the cable RJ 45 connector to the Console port on the X330WAN module The X330WAN enters Modem mode You can now dial into the module from a remote station and open a Telnet session to the PPP interface IP address configured in step 5 22 Avaya X330W 2DS1 User s Guide Configuring the X330 WAN Checking the Modem Configuration After establishing a modem connection use the show interface console command to display information regarding your network interface Verify that the output information is correct Configuring Fast Ethernet Interfaces Before configuring Fast Ethernet interfaces make sure the X330WAN is inserted in the P330 switch and the power is turned on All CLI commands mentioned in this section are described in Chapter 7 X330WAN CLI Commands To configure Fast Ethernet interfaces 1 Type interface FastEthernet 1 to enter the Interface Configuration mode The prompt changes to X33 OWAN 2DS1 N super if FastEthernet1 2 Usethe ip address lt ip address gt lt mask gt command to assign an IP address and subnet mask to the interface 3 Type exit to r
12. WAN CLI Commands The syntax for this command is speed 9600 19200 38400 9600 Sets a speed of 9600 bits per second 19200 Sets a speed of 19200 bits per second 38400 Sets a speed of 38400 bits per second Example X330WAN 2DS1 1 config if CON speed 9600 speed FastEthernet interface context Use the speed command to control the speed setting for the interface Note This command is executed from the Fast Ethernet interface The syntax for this command is speed 10MB 100MB 10MB Sets a speed of 10 Mbps 100MB Sets a speed of 100 Mbps Example X330WAN 2DS1 1 config if FastEthernet1 speed 100MB timeout absolute Console interface context Use the timeout absolute command to set the number of minutes until the system automatically disconnects an idle PPP incoming session The syntax for this command is timeout absolute lt time gt time Number of minutes 0 999 where 0 means no timeout should occur at all Avaya X330W 2DS1 User s Guide 149 Chapter7 _X330WAN CLI Commands voip queue Serial interface context Use the voip queue command to select custom queueing and queue sizes for VoIP traffic Use the no form of this command to restore the default priority queues size to the default The syntax for this command is no voip queue 150 Avaya X330W 2DS1 User s Guide How to Contact Us To contact Avaya s technical support please call In the Unite
13. cookie An integer Example X330WAN 2DS1 1 configure ip distribution access list cookie 4 12345 ip distribution access list copy Use the ip distribution access list copy command to copy the distribution access list Note This command is only supported by the X330WAN module The syntax for this command is ip distribution access list copy lt source list gt lt destination list gt source list An integer 1 99 Avaya X330W 2DS1 User s Guide 111 Chapter 7 X330WAN CLI Commands destination list An integer 1 99 Example X330WAN 2DS1 1 configure ip distribution access list copy 1 3 ip distribution access list name Use the ip distribution access list name command to set the distribution list name Note This command is only supported by the X330WAN module The syntax for this command is ip distribution access list name lt distribution list number gt lt name gt distribution list number An integer 1 99 name List name Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york Example X330WAN 2DS1 1 configure ip distribution access list name 5 evening ip distribution access list owner Use the ip distribution access list owner command to set the policy list owner D Note This command is only supported by the X330WAN module 112 Avaya X330W 2DS1 User s Guide Policy
14. os stout calc E geed bandwidth Interface context eeeeseeseceeeeeeeeeeeeeeeeeees cablelength long Controller Context eene cablelength short Controller Context een channel group Controller context oo Glen fragment eege deelen svencsedeseveuestetaevestaelegerg sitse clock source Controller Context seess COMEOM ee description Controller context sssssssssesessessssrsesissessee description Interface context oes te teteeeeenees G TT duplex FastEthernet interface context en encapsulation ppp Serial interface context e fragment chaim eebe ereeger eer i i e EE ee E fragment Dmeout ENEE framing Controller contexte interface Console ccc etii iiaia iieis isine interface FabricFastEthernet NEE interface FastEthernet e essesessssesseieseriererrsseresiereseereseeees interface Loopback ue Interface Seta secs ninen ee eee e e a a deet keepalive Serial interface context oo eee linecode Controller context ssssssesesereeeeeseesreseerereesseses loopback diag Controller Context onbe loopback local Controller contexte loopback remote Controller context 0 0 mtu Serial interface context oo eeceeceeeeeeteeeceeeeneeeeneeeens no channel group Controller context occas no loopback Controller Context ee ppp authentication Console interface context ppp timeout ncp Serial interface context c ppp timeout retry Serial interface context en Avaya X330W 2DS1 User s Gu
15. 1 super no ip default gateway 70 Avaya X330W 2DS1 User s Guide Layer 3 CLI Commands ip directed broadcast Interface context Use the ip directed broadcast command to enable net directed broadcast forwarding The no form of this command disables net directed broadcasts on an interface Note This command is executed from the Serial Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no ip directed broadcast ip icmp errors Use the ip icmp errors command to set ICMP error messages ON The no form of this command to set ICMP error messages OFF The syntax for this command is no ip icmp errors ip max arp entries Use the ip max arp entries command to specify the maximum number of ARP cache entries allowed in the ARP cache The no form of this command restores to the default value of 4096 This command takes effect only after start up The syntax for this command is no ip max arp entries lt value gt value The space available for the IP address table When you decrease the number of entries it may cause the table to be relearned more frequently If you do not enter a value then the current ARP Cache size is shown The range of accepted values is 128 to 16384 Examples To set the maximum number of ARP cache entries to 8000 X330WAN 2DS1 1 configure ip max arp entries 8000 To restore the maximum number of ARP cache entries to its default X330WAN 2D
16. 4 1 Shock Criteria 4 4 2 Vibration Criteria 5 4 1 Shock and Vibration Test Methods Avaya X330W 2DS1 User s Guide Ill Preface Power amp Heat Dissipation The power and heat dissipation statistics for the X330WAN are listed below e Power for the X330WAN comes from the P330 The X330WAN requires 45 Watts e Heat dissipation the X330WAN conforms to the P330 operating temperature range X330WAN Standards Supported This section provides lists of the standards supported by the X330WAN The following table shows the X330WAN ANSI standards supported ANSI Details T1 231 T1 T1 403 T1 The following table shows the X330WAN ITU T standards supported ITU T Details G 703 E1 G 704 E1 The following table shows the X330WAN RFC standards supported RFC Details 791 Internet Protocol Datagram Reassembly Algorithms 792 Internet Control Message Protocol ICMP 826 Ethernet Address Resolution Protocol ARP 894 Standard for the transmission of IP datagrams over Ethernet 951 Bootstrap Protocol 1058 Routing Information Protocol RIP 1213 MIB II System Group IP MIB SNMP TCP UDP ICMP 1215 Defining Traps for use with the SNMP IV Avaya X330W 2DS1 User s Guide Standards and Compliance RFC Details 1471 Definitions of Manage
17. 832 or more Path Code Violation errors e One or more Out of Frame defects For no CRC E1 signals displays the number of seconds with 2048 or more Line Code Violations Unavail Secs Displays the total number of seconds on the interface calculated by counting the number of seconds that the interface is unavailable show controllers remote Use the show controllers remote command to display far end performance data through an fdl message D Note This command is used when the fdl at amp t option is defined The syntax for this command is show controllers remote lt port gt lt fdl request type gt port Number of the port fdl request Request types include type e 1h data e Enhanced Cl configuration e Enhanced 1h e Errored ESF data Example X330WAN 2DS1 1 super show controllers remote 1 1h data Avaya X330W 2DS1 User s Guide 143 Chapter 7 X330WAN CLI Commands show fragment Use the show fragment command to display information regarding fragmented IP packets that are destined to the router Note No fragmentation will be done of packets in transit through the router This command displays the following information Size Maximum number of packets set by the size option Chain Maximum number of fragments for a single packet set by the chain option Timeout Maximum number of seconds set by the timeout option Queue Number of packets currently awaiting reassembly Assemble Nu
18. Avaya X330W 2DS1 User s Guide 87 Chapter7 _X330WAN CLI Commands Example X330WAN 2DS1 1 configure ping 149 49 50 13 5 8 Output Example X330WAN 2DS1 1 configure ping 149 49 54 1 Reply from 149 49 54 1 bytes 32 time 17ms TTL 64 Reply from 149 49 54 1 bytes 32 time 1ms TTL 64 Reply from 149 49 54 1 bytes 32 time 17ms TTL 64 Ping statistics for 149 49 54 1 Packets sent 3 Received 3 Lost 0 0 loss Approximate round trip times in milli seconds Minimum 1 Maximum 17 Average 9 redistribute Router OSPF context Use the redistribute command to redistribute routing information from other protocols into OSPF The no form of this command disables redistribution by OSPF The syntax for this command is no redistribute lt protocol gt protocol static connected rip Example X330WAN 2DS1 1 configure router ospf redistribute static redistribute Router RIP context Use the redistribute command to redistribute routing information from other protocols into RIP The no form of this command disables redistribution by RIP The default is disabled The syntax for this command is no redistribute lt protocol gt protocol Either Static or OSPF Example X330WAN 2DS1 1 configure router rip redistribute ospf 88 Avaya X330W 2DS1 User s Guide Layer 3 CLI Commands router ospf router rip router vrrp show ip arp Use the router o
19. CLI Commands The syntax for this command is ip distribution access list owner lt policy list number gt lt owner gt policy list number An integer 1 99 owner List owner Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york Example X330WAN 2DS1 1 configure ip distribution access list owner 78 admin ip simulate Use the ip simulate command to check the policy for a simulated packet The command contains the addressed list number and the packet parameters Note This command can only be executed from inside the interface context such as the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces of the X330WAN The syntax for this command is ip simulate lt policy list number gt lt direction gt lt priority gt lt dscp value gt lt source gt lt destination gt lt protocol gt lt source port gt lt destination port gt lt established gt policy list number An integer 100 199 where 0 is the default list direction inl out priority fwd0 fwd1 l fwd7 dspc value dscp0 dscp1 dscp63 source Source IP address destination Destination IP address protocol ip tcp udp integer 1 255 Avaya X330W 2DS1 User s Guide 113 Chapter 7 X330WAN CLI Commands source port An integer 1 65535 destination port An integer 1 65535 established Value of TCP established bi
20. Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no description lt desc gt desc A string describing the interface Examples X330WAN 2DS1 1 config if FastEthernet1 description vlan5 Use the ds mode command to set the controller s mode 126 Avaya X330W 2DS1 User s Guide WAN CLI Commands Note After setting the controller s mode this command will 1 Perform the copy running config startup config command 2 Erase startup config 3 Reset the device The syntax for this command is ds mode e1 t1 el Sets the device in E1 mode All controllers are set to operate as E1 t1 Sets the device in T1 mode All controllers are set to operate as T1 This is the default Output Example X330WAN 2DS1 1 configure ds mode el Your startup config file will be erased Your telnet session will be disconnected This operation may take a few minutes The WAN module will reset in order to make the required change Do you want to continue Y N Note If this command is entered when the correct mode is selected for example entering dal mode e1 when the device is already in E1 mode no errors are generated duplex FastEthernet interface context Use the duplex command to control the duplex setting for the interface The syntax for this command is duplex full half full Full duplex half Halp duplex Avaya X330
21. Up or Down default is Up This parameter is not applicable for the Console interface of the X330WAN To assign the IP address 192 168 22 33 with mask 255 255 255 0 to the interface marketing X33 0WAN 2DS1 configure ip address 192 168 22 33 X33 0WAN 2DS1 configure ip address 255 255 255 0 Avaya X330W 2DS1 User s Guide 67 Chapter 7 X330WAN CLI Commands ip admin state Interface context Use the ip admin state command to set the administrative state of an IP interface The default state is up The syntax for this command is ip admin state lt up down gt up down Administrative state of the interface The choices are up active or down inactive ip bootp dhcp network Interface context Use the ip bootp dhcp network command to select the network from which the bootp dhep server shall allocate an address This command is required only when there are multiple interfaces over the Fabric The no form of this command restores to the default Note This command is executed from the Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no ip bootp dhcp network lt ip net gt ip net The IP subnet Example To select the network 192 168 169 0 as the network from which an address shall be allocated for bootp dhcp requests X330WAN 2DS1 1 configure ip bootp dhcp network 192 168 169 0 ip bootp dhcp relay Use the ip bootp dhcp relay
22. Use the ip routing mode command to set the IP routing mode of the interface In RT MGMT mode the interface functions as a routing interface In RT_PRIMARY_MGMT mode the interface function as both a routing interface and the primary management interface The IP address used in Avaya MultiService Network Manager is the primary management interface IP address Only one interface can be in RT_PRIMARY_MGMT mode By default the first IP address defined is used as the primary Note This command is executed from the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is ip routing mode lt mode gt mode RT_MGMT or RT_PRIMARY_ MGMT mode The syntax for this command for the X330WAN is ip routing mode lt rt primary mgmt gt Example X330WAN 2DS1 1 configure ip routing mode RT PRIMARY MGMT ip vrrp Interface Context Use the ip vrrp command to create a virtual router on the interface Use the no form of this command to delete a virtual router Note This command is executed from the Fast Ethernet and Fabric Fast Ethernet interfaces 82 Avaya X330W 2DS1 User s Guide Layer 3 CLI Commands The syntax for this command is no ip vrrp lt vr id gt vr id Virtual Router ID 1 255 Example X330WAN 2DS1 1 configure ip vrrp 1 ip vrrp address Use the address option to assign an IP address to the virtual router Use the no form of this command to remove
23. a specific port enter the port number after the show controllers command For information on the fields in the output from the show controllers command see Chapter 7 X330W AN CLI Commands Handling E1 T1 Alarms Alarms are reported by the LEDs on the X330WAN and via the CLI When an alarm condition is detected by an X330WAN the module sends a signal to all E1 T1 devices to which it is attached Alarms can therefore be categorized as one of the following e Local Alarm Indication Generated by the X330WAN as a result of a line status problem sensed by the X330WAN e Remote Alarm Request Received by the X330WAN from the remote module The following table provides a list of alarms the type of alarm and the alarm condition on the module from which the alarm originates Table 5 1 Alarms Alarm E1 T1 Alarm Type Originating Alarm LOS LOS Local Alarm Indicator N A LOF Red Local Alarm Indicator N A High Ber Major Local Alarm Indicator N A Avaya X330W 2DS1 User s Guide 33 Chapter 5 Handling E1 T1 Alarms Table 5 1 Alarms Alarm E1 T1 Alarm Type Originating Alarm Low Ber Minor Local Alarm Indicator N A RAI Yellow Remote Alarm Request LOS LOF BER AIS AIS Blue Remote Alarm Request Maintenance request Alarm Conditions The following section discusses the different types of alarms how each alarm type is indicated and possible corrective ac
24. access router modules inserted in each of the switches in the stack with an expansion slot A maximum stack configuration of 10 P334T switches using the X330W 2DS1 provides 480 Ethernet 10 100 ports and 20 E1 T1 ports The X330W 2DS1 is the first product of the X330WAN series The following is a list of X330W 2DS1 features Layer 1 Features Layer 2 Features 2 channelized fractionalized E1 T1 ports RJ 48 connectors 10 100Base T Auto Negotiation Fast Ethernet port 100 Mbps Full Duplex Fabric Fast Ethernet interface for internal connection to the P330 Serial RS 232 RJ 45 port for console and dial in modem connection PPP over channeled and fractional E1 T1 The X330WAN has the ability to map several PPP sessions to a single E1 T1 interface Support for up to 253 VLANs on the Fabric Fast Ethernet LAN interface Any combination of these VLANs can be configured to the X330WAN module Auto Negotiation the 10 100 port on the X330WAN supports Auto Negotiation which automatically detects and supports the duplex mode and speed of a connected device This means that you can simply connect the X330WAN to Ethernet or Fast Ethernet equipment at full or half duplex without configuration VLANs VLANs assigned on the Fabric Fast Ethernet port enable the X330WAN to perform inter VLAN routing This enables the user to configure specific VLANs to access the X330WAN while the remaining VLANs are denied access to the WAN Avaya X330W 2DS
25. address gt ip address IP address of the TIME server Use the set timezone command to assign a timezone name and set the time difference of your WAN relative to the Coordinated Universal Time UTC GMT The minutes parameter can only be set to 30 The syntax for this command is set timezone lt zone name gt lt hours hours min gt zone name Three letter representation of the time zone Output Example set timezone GMT 3 30 Timezone set to GMT offset from UTC is 3 30 hours Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york show boot bank Use the show boot bank command to display the software bank from which the Avaya X330W 2DS1 User s Guide 57 Chapter 7 X330WAN CLI Commands device will boot at the next boot process The syntax for this command is show boot bank Output Example show boot bank Boot bank set to bank a show copy status Use the show copy status command to show the status of the local configuration copy operation The syntax for this command is show copy status Output Example X330WAN 2DS1 1 super show copy status Module 1 Module 2 Source file startup config Destination file running config Host SE Running state Idle Failure display null Last warning No warning show dev log file Use the show dev log file command to display the encrypted device s log fi
26. arp 00 40 0d 00 00 00 3 List IP s that match a vendor MAC Output Example X330WAN 2DS1 1 super sh ip reverse arp 00 10 a4 98 97 e0 Showing 1 rows Address MAC Address I F Type TTL 149 49 70 68 00 10 a4 98 97 e0 e 70 Dynamic 14355 Avaya X330W 2DS1 User s Guide 95 Chapter7 X330WAN CLI Commands show ip route Use the show ip route command to display information about the IP routing table The syntax for this command is show ip route lt ip address gt lt ip mask gt ip address The IP address of the routes ip mask The IP mask of the routes Examples show ip route Display all routes show ip route 137 32 50 13 Display a single route show ip route 137 44 50 13 255 255 255 0 Display range of routes show ip route best match Use the show ip route best match command to display a routing table for a destination address The syntax for this command is show ip route best match lt dst addr gt dst addr IP address Output Example X330WAN 2DS1 1 super sh ip route best match 199 93 0 0 Searching for 199 93 0 0 Showing 1 rows Network Mask Interface Next Hop Cost TTL Source 199 93 0 0 29952994040 e 135new 135 64 76 1 1 n a STAT HI show ip route static Use the show ip route static command to display the static routes 96 Avaya X330W 2DS1 User s Guide Layer 3 CLI Commands The syntax for this command is show ip route static lt ip addr gt lt mask gt ip address The IP add
27. command is only supported by the X330WAN module 108 Avaya X330W 2DS1 User s Guide Policy CLI Commands The syntax for this command is ip composite op notify lt policy list number gt lt composite operation index gt lt notify gt policy list number An integer 100 149 where 0 is the default list composite operation index Index of operation in the table notify send trap no trap Example X330WAN 2DS1 1 configure ip composite op notify 101 17 send trap ip composite op priority Use the ip composite op priority command to set the Layer 2 priority of a policy operation Note This command is only supported by the X330WAN module The syntax for this command is ip composite op priority lt list number gt lt composite op index gt lt priority gt policy list number An integer 100 149 where 0 is the default list composite operation index Index of operation in the table priority fwd0 7 no change Example X330WAN 2DS1 1 configure ip composite op priority 101 17 fwd1 Example X330WAN 2DS1 1 configure ip composite op name 101 17 gold account Avaya X330W 2DS1 User s Guide 109 Chapter 7 X330WAN CLI Commands ip distribution access default action Use the ip distribution access default action command to set the default action for a specific policy list Note This command is only supported by the X330WAN module The syntax for this command is ip
28. configure ip netbios rebroadcast both X330WAN 2DS1 1 configure ip netbios rebroadcast 72 Avaya X330W 2DS1 User s Guide Layer 3 CLI Commands ip netmask format Use the ip netmask format command to specify the format of netmasks in the show command output The no form of this command restores to the default which is a dotted decimal format The syntax for this command is no ip netmask format lt mask format gt The possible mask formats are bitcount Addresses are followed by a slash and the total number of bits in the netmask for example 17 decimal The network masks are in dotted decimal notation For example 255 255 255 0 hexadecimal The network masks are in hexadecimal format as indicated by the leading OX For example OXFFFFFFO00 Example To display netmasks in bitcount format X330WAN 2DS1 1 configure ip netmask format bitcount ip ospf authentication key Interface context Use the ip ospf authentication key command to configure the interface authentication password The no form of this command removes the OSPF password Note This command is executed from the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no ip ospf authentication key lt key gt key A string up to 8 characters Example config if ip ospf authentication key my_pass Avaya X330W 2DS1 User s Guide 73 Chapter 7 X330WAN CLI Comman
29. distribution access default action lt list number gt lt default action gt policy list number An integer 1 99 default action default action deny default action permit Example X330WAN 2DS1 1 configure ip distribution access default action 1 default action deny ip distribution access list Use the ip distribution access list command to create a distribution policy statement Note This command is only supported by the X330WAN module The syntax for this command is ip distribution access list lt policy list number gt lt access list index gt lt action gt lt dest ip gt lt dest wildcard gt any policy list number An integer 1 99 access list index An integer action permit deny dest ip IP network address dest wildcard IP network wildcard address 110 Avaya X330W 2DS1 User s Guide Policy CLI Commands Examples X330WAN 2DS1 1 configure ip distribution access list 1 23 deny 10 10 0 0 0 0 255 255 X330WAN 2DS1 1 configure ip distribution access list 2 24 permit 10 1 1 1 X330WAN 2DS1 1 configure ip distribution access list 20 4 permit any ip distribution access list cookie Use the ip distribution access list cookie command to set the cookie list Note This command is only supported by the X330WAN module The syntax for this command is ip distribution access list cookie lt list id gt lt cookie gt list id An integer 1 99
30. dynamic routing entries from the Routing Table The syntax for this command is clear ip route lt ip addr gt lt ip mask gt ip addr IP address ip mask IP mask address Examples clear ip route Clears all the routing table clear ip route 192 168 49 1 255 255 255 0 Clears a range of entries default metric Interface context Use the default metric command to set the interface RIP route metric value The no form of this command restores the default value 1 Avaya X330W 2DS1 User s Guide 65 Chapter7 _X330WAN CLI Commands The syntax for this command is no default metric lt number gt number The interface route metric value The range is 1 to 15 Example X330WAN 2DS1 1 configure interface default metric 10 default metric Router OSPF context Use the default metric command to set the default metric of redistributed routes The no form of this command restores the default The default metric is 20 The syntax for this command is no default metric lt default metric gt default metric An integer The range is 1 to 65535 Example X330WAN 2DS1 1 configure router ospf default metric 50 default metric Router RIP Mode Use the default metric command to set the default metric of redistributed routes The no form of this command restores the default The default metric is 1 The syntax for this command is no default metric lt default metric gt default metric The interfac
31. serial interface on port number 1 with a channel group number 1 Use the ip address lt ip address gt lt mask gt command to assign an IP address and subnet mask to the interface Repeat steps 2 through 8 if you want to configure another E1 or T1 interface Type exit to return to Supervisor mode The prompt returns to X33 OWAN 2DS1 N super 24 Avaya X330W 2DS1 User s Guide Configuring the X330WAN Note For the first inteface to be configured the following message appears CG The primary management interface has changed For this change to take effect you need to copy running config startup config and then reset the devic You need to issue the copy running config startup config and reset commands Note You cannot delete an interface if there is a primary management IP PMI defined on it Avaya X330W 2DS1 User s Guide 25 Chapter 3 Initial Configuration Configuring Loopback Interfaces Before configuring Loopback interfaces make sure the X330WAN module is inserted in the P330 switch and the power is turned on All CLI commands mentioned in this section are described in Chapter 7 X330W AN CLI Commands To configure Loopback interfaces 1 Enter the Interface Loopback mode using the interface Loopback lt interface number gt ip interface command For example typing interface loopback 1 configures a loopback with a Loopback interface number 1 The prompt cha
32. show ip vrrp detail command to display full VRRP related information The syntax for this command is show ip vrrp detail detail Show full detail information Output Example X330WAN 2DS1 1 configure show ip vrrp detail VRRP is globally enabled Virtual Router on VLAN 1 Router id 1 State MASTER Priority 255 Advertisement Interval 1 Last State Change 00 00 00 Override Address Ownership Rule No Authentication Type None Authentication Key Ve Master IP Address 192 168 66 23 Has 1 IP addresses 98 Avaya X330W 2DS1 User s Guide Layer 3 CLI Commands IP addresses 192 168 66 23 Primary IP Address 192 168 66 23 Primary IP Address was chosen by default Preemption Mode enabled of times Master of received Advertisements of transmitted Advertisements 20 of received Advertisements with Security Violations 0 Virtual Router on VLAN 1 Router id 2 State BACKUP Priority 100 Advertisement Interval 1 Last State Change 00 00 00 Override Address Ownership Rule No Authentication Type None Authentication Key Wed Master IP Address 0 0 0 0 Has 1 IP addresses IP addresses 192 168 66 24 Primary IP Address 192 168 66 23 Primary IP Address was chosen by default Preemption Mode enabled of times Master of received Advertisements of transmitted Advertisements 13 of received Advertisements with Security Violations 0 timers basic Router RIP c
33. the CLI refer to Chapter 7 X330WAN CLI Commands For instructions on using the Device Manager or Avaya MultiService Network Manager refer to the Avaya MultiService Network Manager P330 Device Manager User s Guide on the Documentation and Utilities CD The CLI is command line driven and does not have any menus To activate a configuration option type the desired command at the prompt and press Enter The rest of this section describes the following e How to establish a Serial and Modem connection using the CLI e How to configure an X330WAN Fast Ethernet T1 E1 interface or loopback using the CLI e How to check and save your configuration using the CLI e How to establish a Telnet session using the CLI Establishing a Serial Connection Perform the following steps to connect a terminal to the Console port of the X330WAN module for configuration of WAN parameters using the CLI 1 Use the supplied serial cable to attach the RJ 45 console connector to the Console port on the X330WAN module Connect the DB 9 connector to the serial COM port on your PC terminal 2 Use the following serial port settings on the terminal Baud Rate 9600 bps Character Size 8 Parity None Stop Bit 1 Flow Control None Terminal Emulation VT 100 Note The terminal connected to the Console port must be configured with these settings 3 Press Enter 4 When prompted for a Login Name enter the def
34. the Telnet session by typing telnet lt X330WAN_IP_address gt For example telnet 149 49 32 134 Note You can also Telnet the IP address of the P330 stack If you Telnet the IP address of the stack a connection is established with the Switch CLI entity of the Master module of the stack If you want to connect to the X330WAN CLI entity use the session wan lt module number in stack gt command 4 When prompted for a Login Name enter the default name root Avaya X330W 2DS1 User s Guide 27 Chapter 3 Initial Configuration 5 When prompted for a password enter the User Level password root in lower case letters do NOT use uppercase letters 6 You can now configure the X330WAN X330WAN Default Settings The default settings for the X330WAN and its ports are determined by its firmware These default settings are subject to change Newer versions of the software for the X330WAN can be downloaded from the Avaya Network Software Download Web site http www avaya com support Table 3 2 X330WAN Default Settings Function Default Setting Port Speed Fast Ethernet 100 Mbps Port Duplex Fast Ethernet Full Duplex Auto Negotiation Fast Ethernet Enabled WAN mode WAN T1 Framing WAN SF for T1 CRC4 for E1 Linecode WAN AMI for T1 HDB3 for E1 Clock Source WAN line Cable Length for T1 long gain26 0db Speed for T1 56 SNMP Community public Avaya X330WA
35. words or more must be type in quotation marks e g Operations Floor Example set system location Floor 5 Room 12 set system name Use the set system name command to set mib2 system name MIB variable The syntax for this command is set system name name string name string System name The system name is cleared if this field is left blank A string of 2 words or more must be type in quotation marks e g Backbone Stack Example set system name Banking System set time client The set time client command is used to enable or disable the periodic network time acquisition by the device from the network time server SNTP or TIME protocol The syntax for this command is set time client enable disable set time protocol Use the set time protocol command to set the protocol for use in the system as either SNTP protocol or TIME protocol The syntax for this command is set time protocol sntp protocol time protocol 56 Avaya X330W 2DS1 User s Guide General Device Commands Output Example X330WAN 2DS1 1 super set time protocol sntp protocol The protocol has been set to SNTP protocol Output Example X330WAN 2DS1 1 super set time protocol time protocol The protocol has been set to TIME protocol set time server set timezone The set time server command is used to set the TIME server address The syntax for this command is set time server lt ip
36. 0 Configuring the X330WAN 21 Establishing a Serial Connection 0 cece sees seeseseeseeeeeeeesens 21 Establishing a Modem Connection cccccceessesesessssssseseseneeseesens 22 Checking the Modem Configuration cccccccesecsessseesessssnesesens 23 Configuring Fast Ethernet Interfaces En 23 Configuring E1 T1 Interfaces ue 23 Configuring Loopback Interfaces ENEE 26 Checking the Loopback Fast Ethernet T1 E1 IP Interface Configuration gebiet 26 Saving Your Configuration EE 27 Establishing a Telnet Connection eee eee sesssseesesensseneeees 27 X330WAN Default Settings 28 Chapter 4 Common Configurations cccccscsssscsssessscsesceceseseseseececsessecesessssesseseseseeseees 29 ii Avaya X330W 2DS1 User s Guide Contents Connecting Branch Offices to Headquarters 29 Connecting a Small Office to the Internet 31 Using the X330WAN with Security 32 Chapter 5 Troubleshooting csscosssscsssesssssseseseecssssesesecsssssseseeseessssseseessseeseseseesseoeeees 33 Monitoring Traffic 33 Handling E1 T1 Alarms 33 Alarm Condi Ten EE 34 LOSS sei Ee mis a in in RAs get Bal es EE E 34 QE PAR RE 34 High Ber Majota sieves cle Een 35 RAN VOW es Ee Ee Ee fe 35 AIS ET ns San hia alin ee lees 35 Alarm Dette Ctl Onis asea a teal 3 asso che ldatde bead aee ea iele 36 Using Loopbacks 36 Troubleshooting VoIP Transmission 37 Chapter 6 Embedded Web Manage isisisi keserse ansen seris 39 System Requirements 39 Running the Embedded Manage
37. 1 Effective August 1st 2003 UL60950 Global IEC CB Schema IEC 950 with country deviations for EU Japan report IEC 950 South Korea Brazil and China NOM 16 and 19 Mexico Electromagnetic Compatibility Standards The following table shows the X330WAN compliance with EMC standards Certification Description FCC Part 15 Class A USA Outdoors and Class B Note Class B compliance is obtained with one X330WAN module in a stack of P330 switches More than one expansion module per stack might cause deviation from Class B compliance IECS 003 Class B Canada EN55022 1998 Class B Europe Radiation and Conducted Emissions Based on CISPR 22 Note P330 switches are certified as Class A VI Avaya X330W 2DS1 User s Guide Standards and Compliance Certification Description EN55024 Europe Based on CISPR 24 Immunity Characteristics Includes e IEC61000 4 2 Electrostatic discharge e IEC61000 4 3 Radiated immunity e JTEC61000 4 4 Fast transient e JTEC61000 4 5 Surge immunity e IEC61000 4 6 Immunity to conducted disturbances e IEC61000 4 8 Power frequency magnetic field immunity e IEC61000 4 11 Voltage dips EN61000 3 2 Power supply harmonic current EN61000 3 3 Power supply flicker VCCI Class B Japan Telecommunication Standards The following table shows the X330WAN compliance with Network standards
38. 1 User s Guide 3 Chapter 1 Overview Layer 3 Features Supports RIP v1 v2 routing protocols Supports Single Area OSPF routing protocol the X330WAN can be configured as an OSPF Autonomous System Boundary Router ASBR by configuration of route redistribution The X330WAN can be installed in the OSPF backbone area area 0 0 0 0 or in any OSPF area that is part of a multiple areas network The X330WAN cannot be configured to be an OSPF area border router itself Supports VRRP redundancy protocol supported only on the X330WAN s LAN Fast Ethernet and Fabric Fast Ethernet ports Supports Equal Cost MultiPath ECMP allows load balancing by splitting traffic between several equivalent paths Supports Distribution Lists these lists define which routers are trusted regarding OSPF Routing information is only allowed to be transmitted to or received from the trusted routers Convergence Features Priority queueing the X330WAN supports the ability to separate traffic into 4 strict priority queues per interface The assignment of placement in the queues is performed using Policy Guaranteed delay for VoIP traffic the X330WAN supports VoIP Queue mode In this mode traffic labelled as voice traffic receives preference to all other traffic The X330WAN default mode is optimized for the G 729 codec Random Early Detect RED the X330WAN uses RED in order to improve the performance of the network when overloaded RED sends signa
39. 1 User s Guide 47 Chapter7 X330WAN CLI Commands copy running config tftp Use the copy running config tftp command to copy the device configuration from the current RAM Running Configuration to the TFTP file The syntax for this command is copy running config tftp lt filename gt lt ip gt filename The file name full path ip The IP address of the host Examples X330WAN 2DS1 1 configure copy running config tftp c p332 router1l cfg 192 168 49 10 copy startup config tftp Use the copy startup config tftp command to copy the device configuration from the NVRAM Startup Configuration to the TFTP file The syntax for this command is copy startup config tftp lt filename gt lt ip gt filename The file name full path ip The ip address of the host Examples X330WAN 2DS1 1 configure copy startup config tftp c p332 routerl cfg 192 168 49 10 copy tftp startup config Use the copy tftp startup config command to copy the device configuration from the saved TFTP file to the Startup Configuration NVRAM The syntax for this command is copy tftp startup config lt filename gt lt ip gt filename The file name full path ip The ip address of the host 48 Avaya X330W 2DS1 User s Guide General Device Commands Examples X330WAN 2DS1 1 configure copy tftp startup config c p332 routerl cfg 192 168 49 10 copy tftp EW_archive Use the copy tftp EW_archive command to download the WAN
40. 1 primary 192 168 66 23 ip vrrp priority Use the priority option to set the virtual router priority value used when selecting a master router Use the no form of this command to restore the default value Note This command is executed from the Fast Ethernet and Fabric Fast Ethernet interfaces Avaya X330W 2DS1 User s Guide 85 Chapter 7 X330WAN CLI Commands The syntax for this command is no ip vrrp lt vr id gt priority lt pri value gt vr id Virtual Router ID 1 255 pri value The priority value 1 254 Example To set the priority value for virtual router 1 to 10 X330WAN 2DS1 1 configure ip vrrp 1 priority 10 ip vrrp timer Use the ip vrrp timer command to set the virtual router advertisement timer value in seconds for the virtual router ID Use the no form of this command to restore the default value The syntax for this command is no ip vrrp lt vr id gt timer lt value gt vr id Virtual Router ID 1 255 value The advertisement transmit time seconds The range is from 1 to 255 Example To set the virtual router advertisement timer value for virtual router 3 to 2 X330WAN 2DS1 1 configure ip vrrp 3 timer 2 network Router OSPF context Use the network command to enable OSPF in this network The no form of this command disables the OSPF in this network The default is disabled The syntax for this command is network net addr gt lt wildcard mask gt area
41. 30WAN a series of WAN Edge Router expansion modules for the P330 Stackable Switching System and G700 Gateway The X330WAN is part of Avaya s Converged Networks Solution that includes IP telephones data switches and IP exchanges Each X330WAN access router module contains its own powerful onboard CPU and software which functions as a dedicated WAN Edge Router The X330WAN is designed around the following concepts e WAN access e Routing e Security e Convergence The first of the X330WAN series is the X330W 2DS1 access router module with 2 E1 T1 interfaces a single 10 100Base T Fast Ethernet port and a serial Console port The primary uses of the X330WAN are the following e Branch Office connectivity to Headquarters e Small Medium Business connectivity directly to an ISP Internet Service Provider Branch Office Connectivity to Headquarters The X330WAN enables connecting the LAN of branch offices based on the P330 switch to the headquarters office connecting to the corporate WAN Each branch office in this solution would use the Internet services supplied via the headquarters ISP or connect directly to the Internet independently Installing an X330 WAN Access Router in a a G700 Gateway provides cost effective and space saving IP Telephony and WAN routing for SMEs The G700 and P330 can be stacked together to provide a comprehensive converged solution Small Medium Business Connectivity Directly to a Service Prov
42. 30WAN CLI Commands WAN CLI Commands This section contains a list of all WAN related CLI commands async mode interactive Console interface context Use the async mode interactive command to enter Modem mode every time the proprietary modem cable is plugged into the Console port The syntax for this command is async mode interactive async mode terminal Console interface context Use the async mode terminal command to disable interactive mode on the Console disabling the use of PPP and entering Terminal mode The syntax for this command is async mode terminal async reset modem FastEthernet interface context Use the async reset modem command to reset the connected modem The syntax for this command is async reset modem autoneg Use the autoneg command to set the port speed and duplex to auto negotiation mode Use the no form of this command to disable auto negotiation mode The syntax for this command is no autoneg bandwidth Interface context Use the bandwidth command to set the bandwidth informational parameter Use the no form of this command to set the bandwidth informational parameter to the default Note This command is executed from the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces 120 Avaya X330W 2DS1 User s Guide WAN CLI Commands The syntax for this command is no bandwidth lt kilobits size gt kilobits size An integer 1 10000000 Ex
43. 330WAN 2DS1 1 super ip access list dscp trust 101 trust dscp ip access list name Use the ip access list name command to set a name for a policy list The syntax for this command is ip access list name lt policy list number gt lt name gt policy list number An integer 100 199 or for the X330WAN 100 149 where 0 is the default list name List name Example X330WAN 2DS1 1 super ip access list name 101 morning Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york ip access list owner Use the ip access list owner command to set the owner for a specific policy list The syntax for this command is ip access list owner lt policy list number gt lt owner gt policy list number An integer 100 199 or for the X330WAN 100 149 where 0 is the default list owner List owner 106 Avaya X330W 2DS1 User s Guide Policy CLI Commands Example X330WAN 2DS1 1 super ip access list owner 101 admin ip composite op access Use the ip composite op access command to set the access value of a policy operation Note This command is only supported by the X330WAN module The syntax for this command is ip composite op access lt policy list number gt lt composite operation index gt lt access gt policy list number An integer 100 149 where 0 is the default list composite operation index Index of opera
44. 851 992 080 Mauritius 31 70 414 8054 Switzerland 41 22 827 8741 Morocco 31 70 414 8055 Tanzania 31 70 414 8060 Netherlands 31 70 414 8023 Tunisia 31 70 414 8069 Nigeria 31 70 414 8056 Turkey 800 4491 3919 Norway 47 235 001 00 UAE 31 70 414 8036 Oman 31 70 414 8057 Uganda 31 70 414 8061 Pakistan 31 70 414 8058 UK 44 0207 5195000 Poland 0800 311 1273 Ukraine 31 70 414 8035 Portugal 351 21 318 0047 Uzbekistan 31 70 414 8046 Qatar 31 70 414 8059 Yemen 31 70 414 8062 Romania 31 70 414 8027 Yugoslavia 31 70 414 8038 Russia 7 095 733 9055 Zimbabwe 31 70 414 8063 Saudi Arabia 31 70 414 8022 Email csctechnical avaya com 152 Avaya X330W 2DS1 User s Guide How to Contact Us In the AP Asia Pacific Region Country Local Dial In Country Local Dial In Number Australia 1800 255 233 Hong Kong 2506 5451 Indonesia 800 1 255 227 Japan 0 120 766 227 Korea 0 80 766 2580 Email sgcoe avaya com In the CALA Caribbean and Latin America Region Email caladatasupp avaya com Hot Line 1 720 4449 998 Fax 1 720 444 9103 For updated information visit www avaya com support Number Malaysia 1800 880 227 New 00 800 9828 9828 Zealand Philippines 1800 1888 7798 Singapore 1800 872 8717 Taiwan 0 80 025 227 Avaya X330W 2DS1 User s Guide 153 How to Contact Us All trademarks registered trademarks s
45. CESS ENEE 107 Ip COMPOSIte OP ASCP ENEE 107 IP COMPOSIte OP NAME sirenenet ieia iieiaei iai ei 108 ip composite op notify ENEE 108 ip composite op priority En 109 ip distribution access default action ss sssssssssisssssrsttssserttssseestt gt 110 ip distribution access list EE 110 ip distribution access list cookie cccceseseseetesesteteteeeeeeeeseseetenenes 111 ip distribution access list COPY s ssssseessssisttsssserttssteestssssestenteentes 111 ip distribution access list name ss ssssssssssssrttsssserttssstestssssesttssseestes 112 ip distribution access list OWnNer cccsseseseseeseeteteseeeeneesesesnenenes 112 ip simulate EE 113 DO IP COMPOSHEOP weieireipeiceeniin irern iee ienr EE t i ann aa EE 114 NO ip distribution access list EE 114 set GOS e 115 SHOW iP ACCESS QTOUP ENEE 115 SHOW ip access list ASCP E 116 vi Avaya X330W 2DS1 User s Guide Contents SHOW ip accesg Hete seseeceseeecsseseetetesesesesteesesceeeseseseeneneneees show ip access lists details 0 0 ceeeseseenenenes Show ip access list SUMMALY cccccceseseseeseteseeneeseseenetenes show ip Active ACCESS SLOUPS cececcesesesesteteteseeceteseseetenenes SHOW ip COMPOSIte OP eececccccseeseetstesesesteeseeceenesesteneneneses Validate e WAN CLI Commands async mode interactive Console interface context async mode terminal Console interface context async reset modem FastEthernet interface context HEED
46. Device Manager application into the device via TFTP To use this command you need to have an active TFTP server and to create a file into which to download the data If Avaya MultiService Network Manager is running an additional TFTP server is not required The syntax for this command is copy tftp EW_archive lt filename gt lt ip gt lt mod_num gt filename Embedded Web Manager image file name full path ip The ip address of the TFTP server mod_num Target device number Example X330WAN 2DS1 1 configure copy tftp EW archive c p330 p330web201 192 168 49 10 5 copy tftp SW_image Use the copy tftp SW_image command to update the software image and the device manager applications of a designated device To use this command you need to have an active TFTP server and to create a file into which to download the data If Avaya MultiService Network Manager is running an additional tftp server is not required The syntax for this command is copy tftp SW_image lt sw image file gt EW_archive lt EmWeb_File gt lt ip_address gt The syntax for this command for the X330WAN is copy tftp SW_image lt sw image file gt EW_archive lt ew_archive file gt lt ip_address gt sw image file Common name for the files that contain the Software Image and Embedded Web archive full path Avaya X330W 2DS1 User s Guide 49 Chapter7 _X330WAN CLI Commands EmWeb_File Embedded Web Manager image file name full path
47. E 87 redistribute Router OSPF context cceeeseecseeecseeecneeeeneeeeneeeeneees 88 redistribute Router RIP context oo ee eeeeeseeecneeseneeseneeseneeseeeeseeees 88 POULCT OS PE eege eben Ee E 89 POH TIP Sicha a Eege 89 ee KE 89 SHOW AP ALP E 89 SNOW ee 90 Avaya X330W 2DS1 User s Guide v Contents SHOW ip interface EE 91 SHOW e E 92 Show ip ospf database ENEE 92 Show ip ospf interface NENNEN 93 Show ip ospf neighbor ENEE 93 SHOW ip PLOtOCOIS NENNEN 94 SHOW ip TEVELSC ALP E 95 Sweet edel eege 96 Show ip route best match NEEN 96 SHOW Ip toute EE 96 show ip route SUMMALY ENEE 97 SHOW 1p vrrpd tail soere ep enteeestal eeler eiser 98 timers basic Router RIP context 0 eeseseeeeecneeecneeseeeeeeeeecneeeeneees 99 timers spf Router OSPF context ENEE 100 traceroute ege dee dee SEENEN ENEE NEEN 100 Policy CLI Commands 101 Ip access default ActiOn siise kore notiores ai ris i eies nikai 101 Ip ACCESS STOUP EATA E N ET E O A AE 101 IP ACCESS AIST fests a E TE R ETERA EE 102 UpaCCESS LiSt COOKIE srne e r E e Eeer 103 ELE EE 103 ip access list Ascp operation ccecccccccseseeeeeeeseeceeseseeneesesesneenes 104 ip access list dscp NAME cceceeseseseeseeceseseececetesesesneeeeseeceseseseaenes 104 ip access list dscp Precedence cccccccseeceeesescs ce esesesnsneteseseeteeseseeees 105 Ip access list ASCp trust slais iiio ineeie EEE NE ERE 105 Ip ACCESS liSt MAME ENEE 106 Ip ere ett dee 106 ip COMPOSIte OP AC
48. FastEthernet identifier e Fora FastEthernet interface An integer 1 e Fora Serial interface lt port gt lt channel group gt lt port gt Either 1 or 2 lt channel group gt For E1 an integer 0 30 For T1 an integer 0 23 e Fora FabricFastEthernet interface An integer 1 Avaya X330W 2DS1 User s Guide 147 Chapter 7 X330WAN CLI Commands Examples X330WAN 2DS1 1 super show queueing Interface Name Voip mode Queue 1 High Queue 2 Queue 3 Queue 4 Low shutdown Controller context This command shuts down the E1 T1 link This has the effect of administratively bringing the line down In effect it sends a blue alarm on the line Use the no form of this command to reconnect the E1 T1 link The syntax for this command is no shutdown shutdown Interface context Use the shutdown command to shutdown the selected interface Use the no form of this command to activate the selected interface Note This command is executed from the Serial Loopback Fast Ethernet and Console interfaces The syntax for this command is no shutdown ES Note The no shutdown option is not available in the Console interface speed Console context Use the speed command to set the PPP baud rate to be used by asynchronous PPP ports Note Q 1 This command is executed from the Console interface 2 The peer baud rate must be set to the same value 148 Avaya X330W 2DS1 User s Guide
49. N CLI Entry Login Login name root Password root Avaya X330W 2DS1 User s Guide Chapter A Common Configurations An X330WAN access router module can be used in any situation where E1 T1 WAN connectivity is needed for an office The following situations are the most common configurations for connecting toa WAN using the P330 e Connecting Branch Offices to Headquarters e Connecting a Small Office to the Internet Connecting Branch Offices to Headquarters Many companies have a centralized location for their headquarters and small branch offices It is important that communication between the headquarters and the branches flows quickly The following figure shows a typical configuration of the network connecting the headquarters with branch offices Branch Office to Headquarters Figure 4 1 IP Telephones X330WAN1 Branch Office 135 20 7 8 255 255 0 0 IP Telephones Branch Office 194 49 0 3 255 255 0 0 PPP over E1 T1 with X330WAN E gt a wi n Switches PPP over E1 T1 Avaya X330W 2DS1 User s Guide 29 Chapter 4 Common Configurations The following configuration file is a result of configuring X330WAN1 as shown in Figure 4 1 controller t1 1 channel group 12 timeslots 1 31 controller t1 2 H interface FabricFastEthernet 1 interface FabricFastEthernet 1 30 ip address 135 20 7 8 255 255 0 0 interface FastEthe
50. On Self Test When you power up the Avaya P330 switch with a X330WAN module inserted both perform a self test This test takes about 40 seconds to complete and includes e Checksum tests of boot and system areas of Flash memory e System memory tests e MAC address verification test e System timer test e CAM Contents Addressable Memory tests e Console Port tests e Internal packet forwarding tests e Switch and sub module ASIC Application Specific Integrated Circuit tests e Switch and sub module ASIC memory tests e Sub module interface tests e Sub module packet forwarding tests 14 Avaya X330W 2DS1 User s Guide Avaya P330 LEDs After you insert an X330WAN access router module into a powered P330 switch causing a reset or after a user initiated reset is performed the X330WAN Startup sequence is as follows 1 Ten seconds after startup the ALM LED lights ON for ten seconds then switches OF F 2 The TST LED then lights for twenty seconds and afterwards switches off 3 Thirty seconds after startup the ALM LED lights ON again Note LED Number 51 on the Avaya P330 switch should be ON during the self test procedure The X330WAN module must be inserted completely for the P330 switch to successfully reset Avaya P330 LEDs Figure 2 1 shows an Avaya P330 Switch front panel and a detailed view of the LEDs used when an X330WAN is installed The Avaya P330 Console port is located on the lower right of the P330 switch Anot
51. S1 1 configure no ip max arp entries Avaya X330W 2DS1 User s Guide 71 Chapter 7 X330WAN CLI Commands ip max route entries This command exists for compatibility with P550 There is no limitation on the size of the routing table except for the amount of available memory Use the no form of this command to set the maximum number of route entries in the routing table to its default value The syntax for this command is no ip max route entries lt value gt value number of entries The range of accepted values is 100 to 20000 ip netbios rebroadcast Interface context Use the ip netbios rebroadcast command to set NETBIOS rebroadcasts mode on an interface The no form of this command disables NETBIOS rebroadcasts on an interface Note This command is executed from the Serial Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no ip netbios rebroadcast lt direction gt The possible values of direction is both Netbios packets received on the interface rebrodcasted to other interfaces and netbios packets received on other interfaces are rebroadcasted into this interface If no parameter is provided in the command the both optionis applied as the default disable Netbios packets are not rebroadcasted into or out of this interface Example To enable rebroadcasting of netbios packets received by and sent from the interface marketing X330WAN 2DS1 1
52. User s Guide AVAYA X330W2 DS1 MULTISERVICE WAN ACCESS ROUTER MODULE SOFTWARE VERSION 3 9 May 2002 AVAYA Contents List Of Tab EE ix List Of Figure Sinan e a e EE E E E ESS xi Preface coore trna dee eege Ge ege I About This Guide I beet dee EE deg I HEED ee EE E I Conventions used in the Documentation ccccceccesesecsseseecseesseeaes I EET fos acest oleae et pia eee A eaten Neto BEA BR AG ak A aad Baste I Notes Cautions and Warnings cccsccecescccesesesceteeseseeneeseseees II Before You Install Il le Te II Your Responsibility for Your System s Security 0 II Important Safety Information EE Ill Requirements and Specifications UI Technical Specifications ENEE II Power amp Heat Dissipation En IV X330WAN Standards Supported ene IV Standards and Compliance V Safety Standards Compliance ee VI Electromagnetic Compatibility Standards ee VI Telecommunication Standard ccccccessccssececessseesseceseecsseeesseeees VII NEBS Compliance Standards En VIII How to Contact Us VII Chapter 1 OVEIVICW cssccessssssecsesscsesessscasscessccsesseseceacssesecesesessecescaesceseceseseesceseseaseseseeeaeseeeeoes 1 Branch Office Connectivity to Headquarters ccccscseeeeseeeeees 1 Small Medium Business Connectivity Directly to a ele E TEEN 1 Functional Concepts 2 WAN ACCESS ee 2 ROUNE Sesvetsscecseseevesestevecessctiescanavesedsats xoceslovsnesrstasstonvistarssaveieudebeugvastvvese
53. W 2DS1 User s Guide 127 Chapter 7 X330WAN CLI Commands Example X330WAN 2DS1 1 config if FastEthernet1 duplex full encapsulation ppp Serial interface context Use the encapsulation ppp command to set the encapsulation of the Serial interface to a Router PPP interface Use the no form of this command to close the encapsulation of the Serial interface from a Router PPP interface The syntax for this command is no encapsulation ppp Example X330WAN 2DS1 1 config if Seriall 1 encapsulation ppp fragment chain Use the fragment chain command to set the maximum number of fragments that can comprise a single IP packet destined to the router Use the no form of this command to set the fragment chain to the default value 64 Note No fragmentation will be done of packets in transit through the router The syntax for this command is no fragment chain lt chain limit gt chain limit The maximum number of fragments that can comprise a single IP packet 2 2048 The default is 64 Example X330WAN 2DS1 1 configure fragment chain 30 fdl Use the Tal command to define an fdl type Fdl is used to define a remote loopback for the module or in order to receive the far end counters To disable the fdl use the no command 128 Avaya X330W 2DS1 User s Guide WAN CLI Commands Note 1 This command can only be performed if the controller is set to T1 2 Use this command only when fr
54. WAN Default Settings ENNEN 28 Table 5 1 RER e e EE 33 Table 7 1 X330WAN 2DS1 CLI Prompt NENNEN 46 Avaya X330W 2DS1 User s Guide ix List of Tables x Avaya X330W 2DS1 User s Guide List of Figures Dieure LI Serial Interfaces sa icccseseevedvosesecaviecscesecicessvetuteacssocsivessbencteveveite 9 Figure 1 2 Fabric Fast Ethernet Interfaces EEN 9 Figure 1 3 Fast Ethernet Interfaces ee 10 Figure 1 4 X330W 2DS1 Front Panel ENEE 11 Figure 2 1 LED Indicators for a WAN Access Router Module on the Avaya P330 Front Panell En 16 Figure 4 1 Branch Office to Headoauarters ee 29 Figure 4 2 Small Office to the Internet 31 Figure 4 3 X330WAN with Security 0 0 c cs eeneeecseseeeeeeeee 32 Figure 6 1 The Welcome Dage EEN 40 Figure 6 2 Web based Manager EE 41 Figure 7 1 X330WAN CLI Contexts nisin iai piian 46 Avaya X330W 2DS1 User s Guide xi List of Figures xii Avaya X330W 2DS1 User s Guide Preface About This Guide This guide describes the functioning and features of the X330WAN expansion module and its basic and common configurations The commands specific to the X330WAN module are listed and described in a separate chapter of this guide as well as included in the basic and common configuration chapters Objectives The purpose of this guide is to describe the concepts used in the X330WAN and provide the necessary information to configure and manage the X330WAN module Audience This guide is intend
55. a X330W 2DS1 User s Guide 37 Chapter 5 Troubleshooting VoIP Transmission 38 Avaya X330W 2DS1 User s Guide Chapier 6 Embedded Web Manager The Embedded Web Manager for the X330WAN provides the following e Expansion module configuration e E1 T1 port configuration e Channel group management e Channel group wizard System Requirements H Minimum hardware and Operating System requirements are e One of the following operating systems Windows 95 Windows 98 SP1 Windows 98 OSR Second Edition Windows ME Windows NT Workstation or Server Windows 2000 Professional or Server e Pentium II 400 Mhz based computer with 256 Mb of RAM 512 Mb recommended e Minimum screen resolution of 1024 x 768 pixels e Sun Microsystems Java plug in version 1 3 1_02 supplied e Microsoft Internet Explorer or Netscape Navigator Communicator see table Windows 95 or NT Windows 98 ME or 2000 Internet Explorer 5 0 or higher 5 01 or higher Netscape Navigator 4 7 4 73 Communicator Note for users of Netscape Navigator The Java plug in requires certain services from Windows 95 which are not present if Internet Explorer is not installed In order to add these services to the operating system please install Internet Explorer version 3 or higher You can then use either browser to manage the switch Avaya X330W 2DS1 User s Guide 39 Chapter6 Embedded Web Manager Running the Em
56. ace DS1 frame A slip might happen when there is a difference between the timing of a synchronous receiving terminal and the received signal Displays the number of seconds an Out of Frame OOF error is detected Displays the number of seconds one or more Line Code Violations are detected Displays the number of minutes where the estimated error rate is between 1E 6 and 1E 3 In ESF T1 and CRC4 E1 links displays the number of seconds one of the following is detected e One or more path code violations e One or more Out of Frame defects e One of more Controlled Slip events e An AIS defect In SF T1 and no CRC4 E1 links displays the presence of bipolar violations Displays the number of seconds with e Path Coding Violation errors between1 320 e No Severely Errored Frame defects e No detected incoming AIS defects The number of controlled slips are not displayed 142 Avaya X330W 2DS1 User s Guide WAN CLI Commands Severly Err For ESF T1 signals displays the number of seconds one of the Secs following is detected e 320 or more Path Code Violation Errors e One or more Out of Frame defects e An AIS defect For SF T1 signals displays the number of seconds one of the following is detected e 1544 Line Code Violations e Account of one second intervals with Framing Errors e An Out of Frame defect For CRC E1 signals displays the number of seconds one of the following is detected e
57. ace The IP interface number within this interface as a number of IP interfaces might be bound to an L3 interface An integer between 0 and 1024 Examples X330WAN 2DS1 1 configure interface FastEthernet 1 X330WAN 2DS1 1 configure interface FastEthernet 1 1 X330WAN 2DS1 1 configure no interface FastEthernet 1 1 interface Loopback Use the interface Loopback command to create and or enter interface Loopback configuration mode context Use the no form of this command to delete a Loopback interface or an IP interface The syntax for this command is no interface Loopback lt interface number gt ip interface interface An integer between 0 and 99 number ip interface The IP interface number within this interface as a number of IP interfaces might be bound to an L3 interface An integer between 0 and 1024 Examples X330WAN 2DS1 1 configure interface Loopback 1 132 Avaya X330W 2DS1 User s Guide WAN CLI Commands X330WAN 2DS1 1 configure interface Loopback 1 0 X330WAN 2DS1 1 configure no interface Loopback 1 0 interface Serial Use the interface Serial command to create and or enter Interface Serial configuration mode context For LAN interfaces use this command to create the interface Use the no form of this command to delete an IP interface The syntax for this command is no interface Serial port channel group ip interface port The controller n
58. aces The syntax for this command is no ip rip send receive mode lt mode gt lt default route metric gt where the no form of this command sets the RIP to talk send report mode talk listen Set RIP to receive and transmit updates on the interface talkdefault listen Set RIP to receive updates on the interface and send only a default route Avaya X330W 2DS1 User s Guide 79 Chapter 7 X330WAN CLI Commands listen only Set RIP to only receive updates on the interface and not transmit them for Avaya P332G ML P332GT ML devices only default route metric Integer value Example To set the RIP Send and Receive mode on the interface marketing to be listen only X330WAN 2DS1 1 super if Serial 1 1 ip rip send receive talk listen ip rip split horizon Interface Context Use the ip rip split horizon command to enable split horizon mechanism The no form of this command disables the split horizon By default split horizon is enabled The split horizon technique prevents information about routes from exiting the router interface through which the information was received This prevents routing loops Note This command is executed from the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no ip rip split horizon Example X330WAN 2DS1 1 super if Serial 1 1 no ip rip split horizon 80 Avaya X330W 2DS1 User s Gu
59. aming esf is defined The syntax for this command is no fdl lt fdl mode gt fdl mode ansi att both Example X330WAN 2DS1 1 configure fdl ansi fragment size Use the fragment size command to set the maximum number of fragmented IP packets destined to the router to reassemble at any given time Use the no form of this command to set the fragment size to the default value 100 Note No fragmentation will be done of packets in transit through the router The syntax for this command is no fragment size lt database limit gt database limit The maximum number of packets undergoing re assembly at any given time The default is 100 Example X330WAN 2DS1 1 configure fragment size 150 fragment timeout Use the fragment timeout command to set the maximum number of seconds to reassemble a fragmented IP packet destined to the router Use the no form of this command to set the fragment timeout to the default value 10 Note No fragmentation will be done of packets in transit through the router Avaya X330W 2DS1 User s Guide 129 Chapter 7 X330WAN CLI Commands The syntax for this command is no fragment timeout lt timeout gt timeout An integer 5 120 The maximum number of seconds to re assemble an IP packet The default is 10 Example X330WAN 2DS1 1 configure fragment timeout 30 framing Controller context Use the framing command to select the frame type for th
60. ample X330WAN 2DS1 1 super if FabricFastEthernet1 1 bandwidth 100 cablelength long Controller Context Use the cablelength long command to configure transmit and receive levels for a cable length line build out longer than 655 feet for a T1 trunk with a CSU interface Use the no form of this command to restore the cablelength long parameters to their default Tx 0db level Rx gain26 O Note This command can only be performed if the controller is set to T1 The syntax for this command is no cablelength long gain26 gain36 15db 22 5db 7 5db Odb long Configures parameters using gain attenuation gain26 Sets the receive sensitivity to 26 dB if you can configure the hardware s receive sensitivity This is the default value However it is recommended to enter gain26 so that the CLI entry matches the actual value gain36 Sets the receive sensitivity to 36 dB if you can configure the hardware s receive sensitivity 15db Sets the transmit attenuation to 15 dB 22 5db Sets the transmit attenuation to 22 5 dB 7 5db Sets the transmit attenuation to 7 5 dB Odb Sets the transmit attenuation to 0 dB This is the default value Avaya X330W 2DS1 User s Guide 121 Chapter 7 X330WAN CLI Commands Note If you cannot configure the hardware s receive sensitivity the receive sensitivity is fixed at 36 dB and is unaffected if you enter gain26 or gain36 Example The following example chan
61. an IP address from a virtual router Note This command is executed from the Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no ip vrrp lt vr id gt address lt ip address gt vr id Virtual Router ID 1 255 ip address The IP address to be assigned to the virtual router Example To assign address 10 0 1 2 to virtual router 1 X330WAN 2DS1 1 configure ip vrrp 1 address 10 0 1 2 ip vrrp auth key Use the ip vrrp auth key command to set the virtual router simple password authentication for the virtual router ID Use the no form of this command to disable simple password authentication for the virtual router instance Note This command is executed from the Fast Ethernet and Fabric Fast Ethernet interfaces Avaya X330W 2DS1 User s Guide 83 Chapter 7 X330WAN CLI Commands The syntax for this command is no ip vrrp lt vr id gt auth key lt key string gt vr id Virtual Router ID 1 255 key strin Simple password strin y 8 pte p 8 ip vrrp 1 primary 192 168 66 23 ip vrrp override addr owner Use the ip vrrp override addr owner command to accept packets addressed to the IP address es associated with the virtual router such as ICMP SNMP and TELNET if it is not the IP address owner Use the no form of this command to discard these packets Note This command is executed from the Fast Ethernet and Fabric Fast Ethernet interfaces The syntax
62. an disconnect your telnet session ix Reset do you want to continue Y N Connection closed by foreign host host Use the reset command to restart the system If you want to keep changes you made to the current running configuration use the copy running config startup config command first Note You should perform a reset after downloading software to the device The syntax for this command is reset 52 Avaya X330W 2DS1 User s Guide General Device Commands set boot bank set logout Output Example X330WAN 2DS1 1 super reset This command will reset the module and may disconnect your telnet session xx Reset the device do you want to continue Y N y Connection closed by foreign host Use the set boot bank command to configure the software bank from which the device will boot at the next boot process The syntax for this command is set boot bank lt value gt value bank a bank b Output Example X330WAN 2DS1 1 super set boot bank bank a Boot bank set to bank a The set logout command is used to set the number of minutes until the system automatically disconnects an idle session The syntax for this command is set logout timeout timeout Number of minutes 0 to 999 until the system automatically disconnects an idle session Setting the value to 0 disables the automatic disconnection of idle sessions default is 15 minutes Output Example To set th
63. ault name root D When promoted for a password enter the password root Avaya X330W 2DS1 User s Guide 21 Chapter 3 Initial Configuration Establishing a Modem Connection A PPP connection with a modem can be established only after the X330WAN is configured with an IP address and net mask Also the parameters used in the X330WAN must be compatible with the modem s parameters All CLI commands mentioned in this section are described in the Chapter 7 X330W AN CLI Commands To configure a modem interface 1 2 3 Connect a terminal to the console port of the X330WAN as described in Connecting the Console Port on page 19 When prompted for a Login Name enter the default name root When prompted for a password enter the password root You are now in Supervisor mode At the prompt type interface Console speed and press Enter Enter an IP address and subnet mask for the X330WAN to connect via its PPP interface using the ip address lt ip address gt lt mask gt command Note The PPP interface configured with the interface console command must be on a different subnet from the router interfaces 10 Set the baud rate ppp authentication and ppp time out required to match your modem using the following commands speed lt 9600 19200 38400 gt ppp authentication lt chap none pap gt timeout absolute lt time gt The time entered is in seconds Type async mode interactive
64. bedded Manager Note You should assign an IP address to the X330WAN before beginning this procedure 1 Open your browser 2 Enter the url of the switch in the format http aaa bbb ccc ddd where aaa bbb ccc ddd is the IP address of the switch Note The user name is root The default password for read write access is root Note The Web management passwords are the same as those of the CLI If you have created additional CLI user names or changed the default passwords then you can use those passwords for Web management as well The welcome page is displayed Figure 6 1 The Welcome Page 149 49 77 94 Cajun P330 Avaya Device Management Microsoft Internet Explorer provided by AVAYA Communication x File Edt View Favorites Tools Help Ei s A ES PE z IW ole GiB SG Bw Back Forward Stop Refresh Home Search Favorites History Mail Prit Edit Address http 149 49 77 94 zl aen Links gt Welcome to the Cajun P330 Device Manager This application requires the Sun Microsystems Java Plug In version 1 2 2 to be installed in your browser Tf it is not already installed an automatic installation procedure will be initiated by your browser which will shortly request your confirmation to install this plug in Tf this does not occur within a few seconds you may also o Retrieve it from a local web server After download is complete run the executable you have d
65. ber gt lt default action gt policy list number An integer 100 199 or for the X330WAN 100 149 where 0 is the default list default action default action deny default action permit Example X330WAN 2DS1 1 ip access default action 101 default action deny ip access group Use the ip access group command to activate a specific policy list and direction To suspend the policy list use the no version of this command Note This command can only be executed from inside the interface context such as the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces of the X330WAN The syntax for this command is no ip access group lt policy list number gt lt direction gt policy list number An integer 100 149 where 0 is the default list direction inl out Example X330WAN 2DS1 1 config if FastEthernet1 ip access group 110 Avaya X330W 2DS1 User s Guide 101 Chapter 7 X330WAN CLI Commands out ip access list Use the ip access list command to create a specific policy rule This command defines a policy rule The access list contains several of these rules Each rule pertains to the source IP address the destination IP address the protocol the protocol ports tcp udp if relevant and to the ACK bit in TCP protocol To delete a specific rule use the no form of this command The syntax for this command for the X330WAN is no ip access list lt policy list number gt lt access
66. cation Type of internal memory into which the file is loaded file description Description of the file D Note Ifthe N A is displayed for the EW_Archive file this means that the Device Manager S W is not loaded correctly Download the Device Manager S W again erase startup config The erase startup config command erases the startup configuration NVRAM The syntax for this command is erase startup config get time Use the get time command to retrieve the time from the network The syntax for this command is get time Output Example get time Time is being acquired from server 0 0 0 0 hostname Use the hostname command to change the Command Line Interface CLI prompt The current device number always appears at the end of the prompt Avaya X330W 2DS1 User s Guide 51 Chapter 7 X330WAN CLI Commands no hostname The syntax for this command is hostname lt hostname_string gt hostname_string none displays current hostname string the string to be used as the hostname up to 20 characters Use the no hostname command to return the CLI prompt to its default The syntax for this command is no hostname nvram initialize reset Use the nvram initialize command to reset the WAN parameters to the factory defaults The syntax for this command is nvram initialize Output Example X330WAN 2DS1 1 super nvram initialize This command will restore factory defaults and c
67. command to create and or enter Interface Fabric Fast Ethernet configuration mode context For LAN interfaces use this command to create the interface Use the no form of this command to delete a Fabric Fast Ethernet interface or an IP interface The syntax for this command is no interface FabricFastEthernet port vlan ip interface port An integer with a value of 1 vlan The 802 1q Fabric number An integer between integer 1 and 3071 ip interface The IP interface number within this interface as anumber of IP interfaces might be bound to an L3 interface An integer between 0 and 1024 Example To enter Interface Fabric Fast Ethernet context for port 1 vlan 1 with an IP interface of 1 interface FabricFastEthernet 1 1 1 Examples X330WAN 2DS1 1 configure interface FabricFastEthernet 1 Avaya X330W 2DS1 User s Guide 131 Chapter7 X330WAN CLI Commands X330WAN 2DS1 1 configure interface FabricFastEthernet 1 1 X330WAN 2DS1 1 configure no interface FabricFastEthernet 1 1 interface FastEthernet Use the interface FastEthernet command to create and or enter Interface Fast Ethernet configuration mode context For LAN interfaces use this command to create the interface Use the no form of this command to delete an IP interface The syntax for this command is no interface FastEthernet interface number ip interface interface An integer with a value of 1 number ip interf
68. command to enable relaying of bootp and dhcp requests to the bootp dhcp server The no form of this command disables bootp dhcp relay The default state is disabled The syntax for this command is no ip bootp dhcp relay 68 Avaya X330W 2DS1 User s Guide Layer 3 CLI Commands Examples To enable relaying of BOOTP and DHCP requests X330WAN 2DS1 1 configure ip bootp dhcp relay To disable relaying of bootp and dhcp requests X330WAN 2DS1 1 configure no ip bootp dhcp relay ip bootp dhcp server Interface context Use the ip bootp dhcp server command to adda bootp dhep server to handle bootp dhcp requests received by this interface The no form of this command removes the server A maximum of two servers can be added to a single interface Using the X330WAN the no form of this command remove a bootp server Note This command is executed from the Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no ip bootp dhcp server lt ip address gt ip address The IP address of the server Example To add station 192 168 37 46 as a bootp dhcp server to handle bootp dhcp requests arriving at the interface marketing X330WAN 2DS1 1 configure ip bootp dhcp server 192 168 37 46 ip broadcast address Interface Context Use the ip broadcast address command to update the interface broadcast address The Broadcast address must be filled in with Os or 1s for exampl
69. commands The CLI is accessed by performing one of the following e Telnet to one of the IP interfaces of the X330WAN e Use the session wan command from the Layer 2 agent of the stack e Use the serial Console port on the X330WAN Avaya P330 Device Manager Embedded Web The built in Avaya P330 Device Manager Embedded Web Manager allows you to manage an X330WAN using a Web browser without purchasing additional software This application works with the Microsoft Internet Explorer and Netscape Navigator web browsers and Sun Microsystems Java Plug in The Device Manager is accessed by performing one of the following e Using your Web browser browse to the IP interface configured on the X330WAN e Using your Web browser browse to the Layer 2 agent stack IP address For more information on the Embedded Web Manager refer to Chapter 6 Embedded Web Manager VisAbility When you need extra control and monitoring or wish to manage other Avaya LAN backbone and wireless equipment then the Avaya Multiservice Network Manager MSNM is the answer This suite provides the ease of use and features necessary for optimal network utilization MSNM supports the following operating environments e Windows NT 2000 and Solaris 8 e Stand Alone mode with Windows NT 2000 e HP OpenView for Windows NT 2000 and Solaris 8 Avaya X330W 2DS1 User s Guide 7 Chapter 1 Overview Interfaces The X330WAN includes Physical an
70. d Objects for the IP Network Control Protocol of the Point to Point Protocol 1473 Definitions of Managed Objects for the IP Network Control Protocol for the Point to Point Protocol 1533 DHCP Options and BOOTP Vendor Extensions 1534 Interoperation Between DHCP and BOOTP 1541 Dynamic Host Configuration Protocol DHCP 1542 Clarifications and Extensions for the Bootstrap Protocol 1724 RIP2 1757 Monitoring and Statistics 1812 IPv4 1850 OSPF Version 2 Management Information Base 1858 Security Considerations for IP Fragment Filtering 2096 ipCidRoute Table 2338 VRRP 2494 Definitions of Managed Objects for the DS0 and DS0 Bundle Interface Type 2495 Definitions of Managed Objects for the DS1 E1 DS2 and E2 Interface Types 2508 Compressing IP UDP RTP Headers for Low Speed Serial Links 2863 The Interfaces Group MIB 3128 Protection Against a Variant of the Tiny Fragment Attack Standards and Compliance The X330WAN has undergone all required regulatory compliance test procedures EMC Telco Safety for Type Approval in the following countries e USA e Canada e European Union Avaya X330W 2DS1 User s Guide V Preface e Japan e China e South Korea e Brazil e Mexico e Israel Safety Standards Compliance The following table shows the safety standards compliance for the X330WAN Certification Description CE Europe EN60950 Western Europe Amendments A1 A2 A3 Effective now Amendments A4 A1
71. d States Dial 1 800 237 0016 press 0 then press 73300 In the EMEA Europe Middle East and Africa Region Local Dial In Local Dial In Se Number Albania 31 70 414 8001 Austria 43 1 36 0277 1000 Azerbaijan 31 70 414 8047 Bahrain 800 610 Belgium 32 2 626 8420 Belorussia 31 70 414 8047 Bosnia 31 70 414 8042 Herzegovina Bulgaria 31 70 414 8004 Croatia 31 70 414 8039 Cyprus 31 70 414 8005 Czech Rep 31 70 414 8006 Denmark 45 8233 2807 Egypt 31 70 414 8008 Estonia 372 6604736 Finland 358 981 710 081 Country Nianbex France 33 1 4993 9009 Germany 49 69 95307 680 Ghana 31 70 414 8044 Gibraltar 31 70 414 8013 Greece 00800 3122 1288 Hungary 06800 13839 Iceland 0800 8125 Ireland 353 160 58 479 Israel 1 800 93 00 900 Italy 39 02 7541 9636 Jordan 31 70 414 8045 Kazakhstan 31 70 414 8020 Kenya 31 70 414 8049 Kuwait 31 70 414 8052 Latvia 371 721 4368 Avaya X330W 2DS1 User s Guide 151 How to Contact Us Local Dial In Local Dial In Country Number SIS Number Lebanon 31 70 414 8053 Slovakia 31 70 414 8066 Lithuania 370 2 756 800 Slovania 31 70 414 8040 Luxemburg 352 29 6969 5624 South Africa 0800 995 059 Macedonia 31 70 414 8041 Spain 34 91 375 3023 Malta 31 70 414 8022 Sweden 46
72. d Virtual interfaces Physical Interfaces The following are the X330WAN physical interfaces Virtual Interfaces WAN Interfaces 2 ports configurable for E1 or T1 LAN Interface FastEthernet interface This interface is an autosensing 10 100Mbps Ethernet port It can be used to connect to a LAN or to a firewall VPN P330 Switching Fabric FabricFastEthernet interface This is an internal 100Mbps connection to the P330 switching fabric It supports VLANs and is compatible with the P330 When connecting the X330WAN in Access Router Only mode e g no VPN or firewall this interface can be used to connect to the hosting P330 switch Console Interface used to connect a terminal for local management or a modem for remote management The following are the X330WAN virtual interfaces Loopback This interface is a logical interface that is not mapped to any physical interface Its purpose is to represent the router with an IP address that is always reachable This is mainly used for network troubleshooting It also provides a Router ID in the OSPF routing protocol Since the Loopback Interface is not connected to any physical interface an entry in the routing table cannot have the loopback interface s subnet as its next hop Note The first interface created in the X330WAN should be an IP interface defined over the Loopback interface VLAN on the FabricFastEthernet Interface The P330 can have multip
73. de Requirements and Specifications Important Safety Information You must read the following safety information before carrying out any installation or removal of components or any maintenance procedures Warning Warnings contain directions that you must follow for your personal safety Follow all instructions carefully yY Caution The Avaya P330 switches and modules contain components sensitive to electrostatic discharge Do not touch the circuit board unless instructed to do so Please read the following safety information thoroughly in conjunction with the safety information supplied with the Switch before installing an X330WAN e This unit operates under SELV Safety Extra Low Voltage conditions according to IEC 950 the conditions of which are maintained only if the equipment to which it is installed is also operational under SELV Requirements and Specifications This section provides the technical requirements and specifications of the X330WAN Technical Specifications This section provides the technical specifications for all Avaya X330WAN access router modules currently available The following table shows the X330WAN operating specifications Item Value Operating Temperature 5 to 50 C 23 122 F Operating Humidity 5 to 95 relative humidity non condensing Mechanical Shocks TR NWT 000063 Network Equipment Building System Generic Equipment Requirements chapters 4
74. ds ip ospf cost Interface context Use the ip ospf cost command to configure interface metric The no form of this command sets the cost to its default The default is 1 Note This command is executed from the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no ip ospf cost lt cost gt cost An integer in the range 1 to 65535 Example ip ospf cost 10 ip ospf dead interval Interface context Use the ip ospf dead interval command to configure the interval before declaring the neighbor as dead The no form of this command sets the dead interval to its default The default is 40 Note This command is executed from the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no ip ospf dead interval lt seconds gt seconds An integer in the range 1 to 65535 Example ip ospf dead interval 15 ip ospf hello interval Interface Mode Use the ip ospf hello interval command to specify the time interval between hello s the router sends The no form of this command sets the hello interval to its default The default is 10 74 Avaya X330W 2DS1 User s Guide Layer 3 CLI Commands Note This command is executed from the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no ip ospf hello interval lt seconds gt seconds An integer in
75. e 10 255 255 255 or 10 0 0 0 Note This command is executed from the Serial Fast Ethernet and Fabric Fast Ethernet interfaces Avaya X330W 2DS1 User s Guide 69 Chapter 7 X330WAN CLI Commands The syntax for this command is ip broadcast address lt bc addr gt be addr The broadcast IP address Example ip broadcast address 192 168 255 255 ip default gateway Use the ip default gateway command to define a default gateway router The no form of this command removes the default gateway The syntax for this command for the P332G ML P332GT ML P333R P333R LB is no ip default gateway lt ip address gt lt cost gt lt preference gt The syntax for this command for the X330WAN is no ip default gateway lt ip address gt lt interface type gt lt interface number gt lt cost gt lt preference gt permanent ip address The IP address of the router cost The path cost The default is 1 interface type The interface type interface number The interface name preference Preference either High or Low The default is Low permanent The route will not be disabled if the interface is down Example To define the router at address 192 168 37 1 as the default gateway Router N configure ip default gateway 192 168 37 1 Example X330WAN 2DS1 1 super ip default gateway 132 55 4 45 4 high X330WAN 2DS1 1 super ip default gateway Serial 1 1 permanent X330WAN 2DS1
76. e E1 or T1 data line Use the no form of this command to set the controller s framing type to the default value The syntax for this command is For T1 lines no framing sf esf For E1 lines no framing crc4 no crc4 sf Selects Super frame framing dsx1D4 This is the default value for T1 lines esf Selects Extended super frame framing dsx1ESF crc4 Selects CRC4 framing dsx1E1 CRC MF This is the default value for E1 lines no crc4 Selects no CRC4 framing dsx1E1 MF Note Use this command in configurations where the router or access server is intended to communicate with E1 or T1 fractional data line The service provider determines which framing type sf esf or crc4 is required for your E1 T1 circuit Example The following example selects extended super frame as the T1 frame type X330WAN 2DS1 1 config controller 1 framing esf 130 Avaya X330W 2DS1 User s Guide WAN CLI Commands Example X330WAN 2DS1 1 config controller 1 no framing interface Console Use the interface Console command to enter Console interface Interface Console context to PPP configure mode For LAN interfaces use this command to create the interface Use the no form of this command to set the default Console parameters The syntax for this command is no interface Console Example X330WAN 2DS1 1 configure interface Console interface FabricFastEthernet Use the interface FabricFastEthernet
77. e RIP route metric value The range is 1 to 16 Example X330WAN 2DS1 1 configure router rip default metric 5 distribution list Router RIP Mode Use the distribution list command to filter incoming outgoing networks in route updates The no form of this command deactivates the filter The syntax for this command is no distribution list lt access list number gt lt type gt 66 Avaya X330W 2DS1 User s Guide Layer 3 CLI Commands lt interface gt lt protocol gt access list number An integer The range is 1 to 99 type interface type interface number protocol Examples X33 0WAN 2DS1 in out The interface type a string The interface number static ospf Protocol is only relevant for outgoing out list entries configure router rip distribution list 10 in FabricFastEthernet 1 X33 0WAN 2DS1 configure router rip distribution list 20 out Serial 1 1 X33 0WAN 2DS1 configure router rip distribution list 40 out ospf ip address Use the ip address command to assign an IP address and mask to an interface The no form of the The syntax for this no ip addres ip address mask admin state Example command deletes an IP interface command is s lt ip address gt lt mask gt lt admin state gt The IP address assigned to the interface Mask for the associated IP subnet The administration status either
78. e autonomous system boundary router summary LSAs Optional 92 Avaya X330W 2DS1 User s Guide Layer 3 CLI Commands external Displays information only about the external LSAs Optional network Displays information only about the network LSAs Optional network summary Displays information only about the network LSAs summary Optional router Displays information only about the router LSAs Optional Output Example X330WAN 2DS1 1 super router ospf sho ip ospf database Showing 1 rows Area Type LSA ID Router ID Sequence Age Cksm 0 0 0 0 RTR 149 49 75 71 149 49 75 71 80000001 567 1399 show ip ospf interface Use the show ip ospf interface command to display the OSPF related interface information The syntax for this command is show ip ospf interface lt interface name gt interface name A string the OSPF interface name Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york Output Example X330WAN 2DS1 1 super router ospf show ip ospf interface There are no OSPF interfaces show ip ospf neighbor Use the show ip ospf neighbor command to display OSPF neighbor information on a per interface basis Avaya X330W 2DS1 User s Guide 93 Chapter 7 X330WAN CLI Commands The syntax for this command is show ip ospf neighbor lt interface name gt lt neighbor id gt interface name A string the OSPF
79. e device The syntax for this command is show tftp download upload status Output Example X330WAN 2DS1 1 super show tftp upload status Module zI Source file stack config Destination file c conf cfg Host 149 49 36 200 Running state Executing Failure display null Avaya X330W 2DS1 User s Guide 61 Chapter 7 X330WAN CLI Commands show time Last warning No warning Use the show time command to display the current device time The syntax for this command is show time Output Example X330WAN 2DS1 1 super show time 10 32 34 27 JAN 2000 GMT show time parameters Use the show time parameters command to display the status and parameters The syntax for this command is show time parameters X330WAN 2DS1 1 super show time parameters Client status Enabled Current time L 01 38 31 01 JAN 1970 GMT Timezone set to GMT offset from UTC is 0 hours Time Server 0 0 0 0 I e broadcast address Time acquired from Time Server 0 0 0 0 Time protocol set to TIME protcol show timezone sync time Use the show timezone command to display the current device timezone The syntax for this command is show timezone Output Example X330WAN 2DS1 1 super show timezone Timezone set to GMT offset from UTC is 0 hours Use the sync time command to synchronize the time 62 Avaya X330W 2DS1 User s Guide General Device Commands The syntax f
80. e number of minutes until the system disconnects an idle session automatically X330WAN 2DS1 1 super set logout 20 Sessions will be automatically logged out after 20 minutes of idle time Avaya X330W 2DS1 User s Guide 53 Chapter 7 X330WAN CLI Commands set snmp trap Output Example To disable the automatic disconnection of idle sessions X330WAN 2DS1 1 super set logout 0 Sessions will not be automatically logged out Use the set snmp trap commands to add an entry into the SNMP trap receiver table and to enable or disable the different SNMP traps for a specific receiver First add the rcvr_addr and then enable disable the different traps for it The syntax for this command is set snmp trap lt rcvr_ addr gt set snmp trap lt rcvr addr gt enable disable all vlan_ violation enable Activate SNMP traps disable Deactivate SNMP traps all Optional Specify all trap types vlan_violation Optional Specify the vlan violation trap from the TRAP MIB revr_addr IP address or IP alias of the system to receive SNMP traps Output Example To enable SNMP vlan_violation traps to a specific manager X330WAN 2DS1 1 super set snmp trap 192 168 173 42 enable vlan violation SNMP vlan violation change traps enabled Output Example To enable all traps to a specific manager X330WAN 2DS1 1 super set snmp trap 192 168 173 42 enable all All SNMP traps enabled Output Example To disable SNMP vla
81. e the no channel group command to delete a channel group The syntax for this command is no channel group lt channel num gt channel num ID number to identify the channel group The valid range is from 0 to 23 for T1 lines and from 0 to 30 for E1 lines Example X330WAN 2DS1 1 config controller 1 no channel group 2 no loopback Controller context Use the no loopback command to disable the loopback mode 136 Avaya X330W 2DS1 User s Guide WAN CLI Commands The syntax for this command is no loopback ppp authentication Console interface context Use the ppp authentication command to set if and what type of password should be sent for authentication The syntax for this command is ppp authentication pap chap none pap Password Authentic Protocol Unencrypted password sent for authentication chap Challenge Handshake Authentication Protocol Encrypted password sent for authentication none No password sent Example To select the chap authentication protocol X330WAN 2DS1 1 config if CON ppp authentication chap ppp timeout ncp Serial interface context Use the ppp timeout ncp command to set the maximum time in seconds that the PPP should allow for negotiation of a network layer protocol Use the no form of this command to disable the maximum time that the PPP should allow for negotiation The syntax for this command is no ppp timeout ncp lt Seconds gt Seconds The maximum time in second
82. e the sending of redirect messages on the interface The no form of this command disables the redirect messages By default sending of redirect messages on the interface is enabled Note This command is executed from the Serial Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no ip redirects Examples X330WAN 2DS1 1 configure ip redirect X330WAN 2DS1 1 super if FastEthernet1 ip redirects 76 Avaya X330W 2DS1 User s Guide Layer 3 CLI Commands ip rip authentication key Interface context Use the ip rip authentication key command to set the authentication string used on the interface The no form of this command clears the password Note This command is executed from the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no ip rip authentication key lt password gt password The authentication string for the interface Up to 16 characters are allowed Example X330WAN 2DS1 1 configure ip rip authentication key hush hush ip rip authentication mode Interface context Use the ip rip authentication mode command to specify the type of authentication used in RIP Version 2 packets The no form of this command restores the default value of none Note This command is executed from the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is
83. ebe diag een actus 57 SHOW COPY StAtUs eision ie deed 58 SHOW dev logfile tseisean O Eei 58 shoWwWerasestatUs EE 58 show image version ssssssessiesssssesiestesrissestentestissesnenressisnesneteeneses 59 show module identity NENNEN 59 SHOW rumpipg Conte NEEN 59 len 60 SHOW sStartup COMfig ENEE 60 SHOW Set lid ni rss Fae adie anneal 2 60 show tftp download software status ee 61 show tftp download upload status cccccceeeeeteteee eee eeeenenenes 61 STOW e EE 62 SHOW time Parameter ENNEN 62 SHOW ee EEN 62 e E 62 eet ee Leben aad 63 terminal lengthy ii cies hee edd 63 League elt ee ee de 63 Layer 3 CLI Commands 64 Ee KEE 64 ALP HIMEOUL edel T 64 ClEAP ATP CAChe EE 65 CLEA IP Oe ee R E EE Tae elec eedaas 65 default metric Interface contexte 65 default metric Router OSPF contexte 66 default metric Router RIP Mode AAA 66 distribution list Router RIP Mode AE 66 EE 67 ip admin state Interface context En 68 ip bootp dhcp network Interface contexte 68 ip bootp dhep relay lt 0 sick ctesiit ee dicdeteerdi a E AN 68 ip bootp dhcp server Interface context oo eeseseeeeeenseeeesees 69 iv Avaya X330W 2DS1 User s Guide Contents ip broadcast address Interface Context 0 ee eeseeeees 69 ek EI E 70 ip directed broadcast Interface context oo eee ee ceseeeeee ee teeeeeeees 71 Ip ICIMP CLTOLS EEN 71 UP IMAX ATP ENUTI S ege cosas ee ceva nielen dese EES 71 IP MAX LOULE EMNITIES En 72 ip netbios rebroadcas
84. ed for customers of Avaya who have networking experience and are familiar with router based internetworking Conventions used in the Documentation Documentation for this product uses the following conventions to convey instructions and information e Mandatory keywords are inthe computer bold font e Information displayed on screen is displayed in computer font e Variables that you supply are in pointed brackets lt gt e Optional keywords are in square brackets e Alternative but mandatory keywords are grouped in braces and separated by a vertical bar e Lists of parameters from which you should choose are enclosed in square brackets and separated by a vertical bar e If you enter an alphanumeric string of two words or more enclose the string in inverted commas Avaya X330W 2DS1 User s Guide I Preface 0 Vi A Notes Cautions and Warnings Note Notes contain helpful information or hints or reference to material in other documentation Caution You should take care You could do something that may damage equipment or result in loss of data Warning This means danger Failure to follow the instructions or warnings may result in bodily injury You should ensure that you are qualified for this task and have read and understood all the instructions Before You Install Notice Every effort was made to ensure that the information in this book was complete and accurate at the t
85. eger 1 3071 For a Loopback interface An integer 0 99 Examples X330WAN 2DS1 1 super show interfaces FabricFastEthernet 1 1 is up line protocol is up Physical address is 00 40 0d bf 3b 01 MTU 1500 bytes Bandwidth 100000 Kbit Encapsulation ARPA 0 packets input Received 0 broadcasts 33175 input errors 0 packets output 0 output errors FastEthernet 1 is up line protocol is up Physical address is 00 40 0d bf 3b fe Internet address is 149 49 75 71 mask is 255 255 255 0 MTU 1500 bytes Bandwidth 100000 Kbit Encapsulation ARPA Full duplex 100Mb 100BaseTX FX ARP type ARPA ARP Timeout 04 00 00 680031 packets input Received 661406 broadcasts 17 input errors 5569 packets output 0 output errors FabricFastEthernet 1 is up line protocol is up MTU 0 bytes Bandwidth 100000 Kbit Encapsulation ARPA 0 packets input Received 0 broadcasts 0 input errors Avaya X330W 2DS1 User s Guide 145 Chapter7 X330WAN CLI Commands 0 packets output 0 output errors Serial 1 1 is down line protocol is down Internet address is 2 2 2 2 mask is 255 255 255 0 advertised IPCP MTU 1500 bytes Bandwidth 256 Kbit Encapsulation PPP CP REQsent IPCP Starting 0 packets input Received 0 broadcasts 0 input errors 3872 packets output 0 output errors Console asynchronous mode is terminal Terminal baud rate is 9600 show ip distribution access lists Use the sh
86. er commands see General Device Commands on page 47 For a list of all Interface Fast Ethernet commands see interface FastEthernet on page 132 For a list of all Interface Fabric Fast Ethernet commands see interface FabricFastEthernet on page 131 For a list of all Interface Loopback commands see async mode interactive Console interface context on page 120 For a list of all Interface Serial commands see interface Serial on page 133 Avaya X330W 2DS1 User s Guide 45 Chapter 7 X330WAN CLI Commands The following figure illustrates this introduction Figure 7 1 X330WAN CLI Contexts User Mode l Configure Context Controller Context Interface Console Context or Other Contexts Interface Fast Ethernet Context or Interface Fabric Fast Ethernet Context or Interface Loopback Context or Interface Serial Context X330WAN CLI Prompts The following table displays examples of X330WAN 2DS1 CLI prompts Table 7 1 X330WAN 2DS1 CLI Prompts Mode Context Prompt User X33 0WAN 2DS1 N gt Supervisor X33 0WAN 2DS1 N super Configure X33 0WAN 2DS1 N configure Controller X33 0WAN 2DS1 N config controller n Interface X33 0WAN 2DS1 N config if CON Console Interface Fast X33 0WAN 2DS1 N config if FastEthernet1 Ethernet Interface Fabric X330WAN 2DS1 N config if FabricFastEthernetn Fast Ethernet Interface X33 0WAN 2DS1 N config if L
87. ervice names product and or brand names are the sole property of their respective owners Copyright 2002 Avaya Inc All rights reserved 154 Avaya X330W 2DS1 User s Guide
88. es 2 DECULITY steet Ei Aan MURR ah Moe iia annals 2 CONMVEL SEN CE ic eege 2 Features 3 Layer TL Features sccccccce ccteescoxcesessiscceusces cnvsnoveseasvecs v seenssevedougensvbsastsveeese 3 Layer 2 Features cs cisissaiitinr geed 3 ayer 3 Pea tures isc tsitita ea tena etaraino ei aeii ba Saine iSe ia 4 Avaya X330W 2DS1 User s Guide i Contents Convergence Fettes dutiiies aro ae aE eE E ESE 4 QoS Features ninina eg EE Ee 5 POLICY eiae e ie aie RAE E E R E EE 5 Controlling Network Access to the X330WAN een 6 Avaya X330WAN Network Management ccccccssesesesssesesesesens 7 Command Line Interface CLI oo eeeseeeseceeseeeeseeeceeeeeneeeeneeeees 7 Avaya P330 Device Manager Embedded Web n nssssn1ssss1ss115 7 MISA UE 7 Tite oe EE E Physical Interfaces neiseis oeae elea Eea eLis 8 Kate TIR E Data Flow 10 Front Panels and LEDs 10 X330W 2DST Front Paneli sneered e a A EEN 11 KEIER EN EEN 11 Chapter 2 Installation E 13 Safety Information 13 Device Support 13 Before You Install 13 Installing an X330WAN Module into an Avaya P330 Switch 14 Power Oni Self eebe AER 14 Avaya P330 LEDs 15 Removing an X330WAN Module from an Avaya P330 Switch 16 Chapter 3 Initial Configuration cccssssscssessssssssssssssssssssssssssssssesssssssssessssssesesseseees 19 Connecting the X330WAN 19 Connecting the E1 T1 Ports NENNEN 19 Connecting the Ethernet Port ue 19 Connecting the Console Port ENEE 19 Console Pin Assignment NENNEN 2
89. eturn to Supervisor mode The prompt returns to X33 OWAN 2DS1 N super Note For the first inteface to be configured the following message appears CG The primary management interface has changed For this change to take effect you need to copy running config startup config and then reset the device You need to issue the copy running config startup config and reset commands Note You cannot delete an interface if there is a primary management IP PMI defined on it Configuring E1 T1 Interfaces Before configuring E1 T1 interfaces make sure the X330WAN is inserted in the P330 switch and the power is turned on All CLI commands mentioned in this section are described in Chapter 7 X330W AN CLI Commands For a list of X330WAN default settings see X330WAN Default Settings on page 28 or use the show controllers lt port gt command to display all of the current settings Avaya X330W 2DS1 User s Guide 23 Chapter 3 Initial Configuration To configure E1 or T1 interfaces 1 10 Use the show controllers lt port gt command to check if your controller s mode is configured as E1 or T1 Use the ds mode e1 t1 command to set the controller s mode to E1 or T1 Changing the line type causes the module to reset Use the controller e1 t1 lt port number gt command to set the port number to be configured The prompt changes to X33 OWAN 2DS1 N super controller n where N is t
90. fault policy source is policy server D Note Before configuring the IP access list you must change the policy source mode to local The syntax for this command is set qos policy source lt source gt source local policy server Example X330WAN 2DS1 1 configure set qos policy source local show ip access group Use the show ip access group command to display information about the configured active access groups The syntax for this command for the X330WAN is show ip access group lt interface name gt lt directions gt Avaya X330W 2DS1 User s Guide 115 Chapter 7 X330WAN CLI Commands interface name string e g FastEthernet 0 direction in out Output Example X330WAN 2DS1 1 configure show ip access group FastEthernet 1 in Note This command is available out of context only show ip access list dscp Use the show ip access list dscp command to display the DSCP table of a given policy list Note This command is only supported by the X330WAN module The syntax for this command is show ip access list dscp lt policy list number gt lt dscp gt policy list number The policy list number integer from 100 to 199 Entering 0 displays the default list dscp DSCP entry integer from 0 to 63 Example X330WAN 2DS1 1 configure show ip access list dscp 101 63 116 Avaya X330W 2DS1 User s Guide Policy CLI Commands show ip access lists Use the show
91. for this command is no ip vrrp lt vr id gt override addr owner vr id Virtual Router ID 1 255 Example X330WAN 2DS1 1 configure ip vrrp 1 override addr owner ip vrrp preempt Use the ip vrrp preempt command to configure the router to preempt a lower priority master for the virtual router ID Use the no form of this command to disable preemption for the virtual router instance By default preemption is enabled Note This command is executed from the Fast Ethernet and Fabric Fast Ethernet interfaces 84 Avaya X330W 2DS1 User s Guide Layer 3 CLI Commands The syntax for this command is no ip vrrp lt vr id gt preempt vr id Virtual Router ID 1 255 Example X330WAN 2DS1 1 configure ip vrrp 1 preempt ip vrrp primary Use the ip vrrp primary command to set the primary address that shall be used as the source address of VRRP packets for the virtual router ID Use the no form of this command to return to the default primary address for the virtual router instance By default the primary address is selected automatically by the device Note This command is executed from the Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no ip vrrp lt vr id gt primary lt ip address gt vr id Virtual Router ID 1 255 ip address Primary IP address of the virtual router This address should be one of the router addresses on the Fabric Example ip vrrp
92. ges the CLI receive sensitivity to match the actual receive sensitivity of the hardware and adds 15 dB of attenuation to the transmit signal X330WAN 2DS1 1 config controller 1 cablelength long gain36 15db Example no cablelength cablelength short Controller Context Use the cablelength short command to configure transmit attenuation for a cable length line build out of 655 feet or shorter for a T1 trunk with a DSX 1 interface Use the no form of this command to restore the default value Note This command can only be performed if the controller is set to T1 The syntax for this command is cablelength short 133 t 266ft 399ft 533 t 655ft short Configures parameters using the loop length 133 Cable length of 0 to 133 feet This is the default value 266 Cable length of 134 to 266 feet 399 Cable length of 267 to 399 feet 533 Cable length of 400 to 533 feet 655 Cable length of 534 to 655 feet 122 Avaya X330W 2DS1 User s Guide WAN CLI Commands Note The transmit attenuation value is best obtained by experimentation If the signal received by the far end equipment is too strong reduce the transmit level by entering additional attenuation Example The following example sets the transmit attenuation to the appropriate levels for a cable between 134 and 266 feet long X330WAN 2DS1 1 config controller 1 cablelength short 266ft channel group Controller context Use the chan
93. he Avaya P333R and P333R LB It provides support for the major routing protocols It also provides a L3 L4 Policy classifier working per Layer 2 interface direction controlling access and QoS tagging and mapping to internal queuing mechanism The X330WAN independently controls all traffic flow in the P330 from the LAN to the WAN The X330WAN currently contains the infrastructure for all security functionality planned for future releases such as Firewall and VPN Licenses will be issued for different security options when development is completed Security currently can be achieved with the X330WAN for the initial release by connecting the Fast Ethernet port of the X330WAN via an external firewall to a port on the P330 switch The X330WAN module is connected to the Internet via it s WAN ports The X330WAN enables a combined data and VoIP solution when used in conjunction with a VoIP gateway such as the G700 This is achieved by connecting the G700 to the LAN s P330 stack and inserting the X330WAN in one of the Avaya X330W 2DS1 User s Guide Features expansion slots either of the P330 stack or of the G700 Standard IP phones can be connected to the P330 stack or Avaya Legacy phones can be connected directly to the G700 Gateway In this solution the X330WAN provides access to the corporate WAN while end to end QoS and Policy ensure that the IP telephony functions flawlessly Features An Avaya P330 stack may have X330WAN
94. he switch number and o is the port number Use the following commands if you want to change the clock source frame type and linecode parameters from their default settings clock source line internal framing sf esf for T1 lines or framing crc4 no crc4 for E1 lines linecode ami b8zs for T1 lines or linecode ami hdb3 for E1 lines cablelength long short for T1 lines If you are working in E1 mode go to step 4 otherwise go to step 5 Use the channel group channel no timeslots timeslot list command to specify the channel group and time slots to be mapped For example typing channel group 1 timeslots 1 3 5 7 configures time slots numbered 1 3 5 and 7 to be mapped in channel group number 1 Proceed to step 6 Use the channel group channel no timeslots timeslot list speed lt 56 64 gt command to specify the channel group time slots to be mapped and DSO speed in kbps For example typing channel group 1 timeslots 1 3 5 7 speed 64 configures time slots numbered 1 3 5 and 7 to be mapped in channel group number 1 and the DSO speed to 64 kbps The default DSO speed is 56 kbps Type exit to return to Supervisor mode The prompt returns to X33 0OWAN 2DS1 N super Use the interface Serial port channel group ip interface command to configure each channel group as a virtual serial interface Specify the port number and channel group number to modify For example typing interface Serial 1 1 configures a
95. her group of LEDs is located on the X330WAN itself For a description of the X330WAN s front panel LEDs see X330WAN LEDs in Chapter 1 Overview Avaya X330W 2DS1 User s Guide 15 Chapter2 Installation Figure 2 1 LED Indicators fora WAN Access Router Module on the Avaya P330 Front Panel WAN Sub module ge LEDs Fast Ethernet Port LED a SYS OPR PWR Left Right and Reset both FIV Switch Function LEDs Switches D Note All LEDs light while the P330 resets The P330 switch front panel LEDs consist of Port LEDs and Function LEDs The Port LEDs display information for each port according to the illuminated function LED The function is selected by pressing the Left Right switch until the desired parameter LED is illuminated Pressing the same switch again will move to the next function When the X330WAN module is installed inside a P330 switch Port LED number 51 displays the status of the X330WAN Fast Ethernet port As a result only Port LED number 51 illuminates when the X330WAN is in use For a description of the other LEDs on the front panel of the Avaya P330 switch refer to the User s Guide that accompanies your switch Removing an X330WAN Module from an Avaya P330 Switch To remove an X330WAN module from a P330 switch 1 Loosen the screws on the front panel of the X330WAN module that secure the 16 Avaya X330W 2DS1 User s Guide Removing an X330WAN Module from an Avaya P330 Switch
96. ide Layer 3 CLI Commands ip route Use the ip route command to establish a static route The no form of this command removes a Static route The syntax for this command is no ip route lt ip addr gt lt mask gt lt next hop gt lt next hop gt lt next hop gt lt interface type gt lt interface number gt lt cost gt lt preference gt permanent Null0 ip address The IP address of the network mask Mask of the static route next hop The next hop address in the network cost The path cost The default is 1 preference Preference either High or Low Default is Low Null Creates a static discard route interface type The interface type interface number The interface number permanent The route will not be disabled if the interface is down Examples X330WAN 2DS1 1 configure ip route 132 55 0 0 255 255 0 0 132 55 4 45 3 high X330WAN 2DS1 1 configure no ip route 134 66 0 0 255 255 0 0 X330WAN 2DS1 1 configure ip route 135 0 0 0 255 0 0 0 Serial 1 1 permanent X330WAN 2DS1 1 configure ip route 134 66 0 0 255 255 0 0 Nullo Avaya X330W 2DS1 User s Guide 81 Chapter 7 X330WAN CLI Commands ip routing Use the ip routing command to enable IP routing The no form of this command disables the IP routing process in the device By default IP routing is enabled The syntax for this command is no ip routing ip routing mode Interface Context
97. ide vii Contents How to Contact Us queue limit Serial interface context ee 138 remote Controller contex aucona nin 138 SHOW controllers stoeren eeeh ie e aereis ES 139 show controllers remote cccsceeccecssseseeseeseeeeescceeceeeeeeceeaeeeeeaeeaeenes 143 Show fragment iere 144 SHOW Erste edel E E E EE 144 show ip distribution access lists cccseeseseseseeeeteseeeeneteeseeneenes 146 show Le CONSOLE soree eegen een E e aa ee eiS E 146 SHOW logout eiiie enre eiia Rea A EA 147 SHOW GUCUCING EE 147 shutdown Controller context eeseseeseseeeeieisrsrsrisesreirrssssrseseseerere 148 shutdown Interface context esesesesesrerereresereererererererrreerererereseeeree 148 speed Console context En 148 speed FastEthernet interface context s ssessssssesississssseeseesressess 149 timeout absolute Console interface context eessceeceeeeeeee 149 voip queue Serial interface context ssssssssissesssissestesressissessees 150 Et EE EEEE 151 Inthe United States osonro iive aeaee iio EEE 151 In the EMEA Europe Middle East and Africa Region 151 In the AP Asia Pacific Region EE 153 In the CALA Caribbean and Latin America Region 0 153 viii Avaya X330W 2DS1 User s Guide List of Tables Table 1 1 X330WAN LED Descriptions NEEN 11 Table3 1 Pinout of the Required Connection for Console COMMUNICATIONS seed Eege Se nies cheered EE EEN 20 Table 3 2 X330
98. ider The X330WAN access router enables SMEs Small Medium Enterprises to connect their LAN directly to an ISP using a P330 switch This solution provides independence and flexibility to the SMEs in the flow of data and other Internet services Avaya X330W 2DS1 User s Guide 1 Chapter 1 Overview Functional Concepts WAN Access Routing Security Convergence One basis for success in today s business world is combining resources The X330WAN supplies you with combined required access functionality for branch offices and SMEs The X330WAN was designed and developed to include all of the functions necessary for branch offices and SMEs The following sections describe the overall concepts that together comprise the functioning of the X330WAN access router For examples of common configurations using the following concepts refer to Chapter 4 Common Configurations WAN access provides a link for routing packets between their WAN and Ethernet LAN interfaces enabling heavy data transfer WAN access can connect branch offices to headquarters and provide fast access to the Internet and e mail When combined with the Avaya G700 Gateway or to the Avaya DEFINITY VoIP services are provided The X330WAN access router modules provides routing capabilities in a P330 device They route packets between their WAN and Ethernet LAN interfaces The X330WAN access router modules routing software is based on the routing software of t
99. ime of printing However information is subject to change Your Responsibility for Your System s Security Toll fraud is the unauthorized use of your telecommunications system by an unauthorized party for example persons other then your company s employees agents subcontractors or persons working on your company s behalf Note that there may be a risk of toll fraud associated with your telecommunications system and if toll fraud occurs it can result in substantial additional charges for your telecommunications services You and your system manager are responsible for the security of your system such as programming and configuring your equipment to prevent unauthorized use The system manager is also responsible for reading all installation instruction and system administration documents provided with this Product in order to fully understand the features that can introduce risk of toll fraud and the steps that can be taken to reduce that risk Avaya does not warrant that this product is immune from or will prevent unauthorized use of common carrier telecommunication services or facilities accessed through or connected to it Avaya will not be responsible for any charges that result from such unauthorized use If you suspect that you are being victimized by toll fraud and require assistance contact the Toll Fraud Intervention Hotline at 1 800 643 2353 or contact your local Avaya representative Il Avaya X330W 2DS1 User s Gui
100. interface name neighbor id Neighbor ID an IP address Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york Output Example X330WAN 2DS1 1 super router ospf show ip ospf neighbor There are no ospf neighbors show ip protocols Use the ip protocols command to display parameters and statistics of the IP routing protocol process The syntax for this command is show ip protocols lt protocol gt protocol RIP OSPF Examples show ip protocols Displays all running protocols details show ip protocols RIP Displays RIP details 94 Avaya X330W 2DS1 User s Guide Layer 3 CLI Commands Output Example Routing Protocol is rip Sending updates every 30 seconds next due in 0 seconds Invalid after 180 seconds flushed after 300 Redistributing rip Default version control rip version 1 Interface Version Key Routing for Networks Routing Information Sources Gateway Last Update Note entire name in quotation marks e g new york show ip reverse arp Use the show ip reverse arp command to display the IP address of a host based on a known MAC address The syntax for this command is show ip reverse arp lt mac addr gt lt match len gt mac addr MAC address match len The number of bytes in the address to match Examples show ip reverse arp 00 40 0d 67 53 04 List IP s that match the MAC show ip reverse
101. ion X330WAN 2DS1 1 configure show ip interface FastEthernet 1 0 Example To display the IP s interface X330WAN 2DS1 1 configure show ip interface 192 168 49 1 Output Example X330WAN 2DS1 1 super show ip interface Showing 2 Interfaces Serial 1 1 is down Avaya X330W 2DS1 User s Guide 91 Chapter 7 X330WAN CLI Commands Internet address is 2 2 2 2 subnet mask is 255 255 255 0 Advertised IPCP address Broadcast address is 2 2 2 255 Directed broadcast forwarding is disabled Proxy ARP is disabled Primary management IP interface FastEthernet 1 is up Internet address is 149 49 75 71 subnet mask is 255 255 255 0 Broadcast address is 149 49 75 255 Directed broadcast forwarding is disabled Proxy ARP is disabled show ip ospf Use the show ip ospf command to display general information about OSPF routing The syntax for this command is show ip ospf Output Example X330WAN 2DS1 1 super router ospf show ip ospf Routing Process OSPF with ID 149 49 75 71 Number of areas in this router is 1 Area 0 0 0 0 Number of Interfaces in this area 0 SPF algorithm executed 1 times SPF hold time is 3 sec show ip ospf database Use the show ip ospf database command to display lists of information related to the OSPF database for a specific router The syntax for this command is show ip ospf database asbr summary router network network summary external asbr summary Displays information only about th
102. ion Displays all ARP mapping marketing Displays an interface ARP mapping 192 168 49 1 Displays one host ARP mapping 192 168 49 1 255 255 255 0 Displays a range of ARP mapping marketing _vlan Displays Fabric ARP mapping static Displays static ARP mapping Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york show ip icmp Use the show ip icmp command to display the status enabled disabled of ICMP error messages The syntax for this command is show ip icmp 90 Avaya X330W 2DS1 User s Guide Layer 3 CLI Commands show ip interface Use the show ip interface command to display information for an IP interface The syntax for this command for the X330WAN is show ip interface lt interface name gt lt IP interface gt lt ip address gt interface name The name of the interface whose information you want to display ip address The IP address of the interface whose information you want to display IP interface A string up to 32 characters Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york Example To display all IP interfaces X330WAN 2DS1 1 configure show ip interface Example To display all IP interfaces on one interface X330WAN 2DS1 1 configure show ip interface FastEthernet 1 Example To display specific IP interface informat
103. ip access lists command to see all the current policy lists The syntax for this command is show ip access lists lt policy list number gt policy list number The policy list number integer from 100 to 199 where 0 is the default list Output Example X330WAN 2DS1 1 configure show ip access lists ip access list 100 10 deny and notify tcp 192 168 55 0 0 0 0 255 range 5000 6000 any range 7000 8000 ip access list 100 30 deny udp any any optional ip access list 100 35 deny ip any any ip access list 100 55 fwd7 tcp host 192 168 3 4 eq 33333 host 10 6 7 8 default action for list 100 is permit show ip access lists details Use the show ip access lists details command to view complete data of a policy list including DSCP and composite operation tables CG Note This command is only supported by the X330WAN module The syntax for this command is show ip access lists details lt policy list number gt policy list number The policy list number integer from 100 to 199 Entering 0 displays the default list Avaya X330W 2DS1 User s Guide 117 Chapter 7 X330WAN CLI Commands Example X330WAN 2DS1 1 configure show ip access list details 101 show ip access list summary Use the show ip access list summary command to display the policy list summary KR Note This command is only supported by the X330WAN module The syntax for this command is show ip access list summary show ip acti
104. le The syntax for this command is show dev log file show erase status Use the show erase status command to view the status of the erase Startup Configuration operation 58 Avaya X330W 2DS1 User s Guide General Device Commands The syntax for this command is show erase status show image version Use the show image version command to display the software version of the image on both memory banks of the device The syntax for this command is show image version Output Example X330WAN 2DS1 1 super show image version Mod Module Type Bank Version 1 Avaya X330W 2DS1 WAN Router A N A ab Avaya X330W 2DS1 WAN Router B 32955 show module identity Use the show module identity command to display the device identity required for acquiring a license The syntax for this command is show module identity Output Example show module identity X330WAN 2DS1 1 super show module identity Mod Module Identity 1 1234567 show running config Use the show running config command to show the RAM based configuration currently running on the device The syntax for this command is show running config Avaya X330W 2DS1 User s Guide 59 Chapter 7 X330WAN CLI Commands show snmp Use the show snmp command to display SNMP information The syntax for this command is show snmp Output Example X330WAN 2DS1 1 super show snmp Authentication trap disabled Community Access C
105. le VLANs defined within its switching fabric To connect to the switching fabric the X330WAN supports up to 253 VLANs Serial Link This is a virtual interface that is created over a portion of an E1 or a T1 This interface is used to directly connect the X330WAN to another device at the other end of a leased line and supports Encapsulation PPP and Frame Relay protocols Avaya X330W 2DS1 User s Guide Interfaces Figure 1 1 provides a graphic representation of the serial interfaces Figure1 1 Serial Interfaces El T1 Layer 1 Interface gt PPP Session 1 gt PPP Session 2 IP Interface 1 IP Interface 2 IP Interface 3 IP Interface 4 IP Interface 5 IP Interface 6 Figure 1 2 provides a graphic representation of the Fabric Fast Ethernet interfaces Figure 1 2 Fabric Fast Ethernet Interfaces Fabric Fast Ethernet Interface IP Interface 1 IP Interface 2 IP Interface 3 IP Interface 4 IP Interface 5 IP Interface 6 Avaya X330W 2DS1 User s Guide Chapter 1 Overview Figure 1 3 provides a graphic representation of the Fast Ethernet interfaces Figure 1 3 Fast Ethernet Interfaces IP Interface 1 IP Interface 2 Fast Ethernet IP Interface 3 Interface IP Interface 4 IP Interface 5 IP Interface 6 Note One or more IP interfaces can be defined over each virtual Fast Ethernet or Fabric Fast Ethernet interfaces Data Flow The X330WAN has the followi
106. list index gt lt action gt lt protocol gt lt source ip gt lt source wildcard gt any host lt source ip gt lt operator gt lt port gt lt port lt destination ip gt lt destination wildcard gt any host lt destination ip gt lt operator gt lt port gt lt port gt established precedence access list number An integer 100 149 policy list number An integer 100 149 access list index An integer 1 9999 command permit deny deny and notify fwd0 7 action permit deny deny and notify fwd0 7 composite op name protocol ip tcp udp integer 1 255 source ip IP network source wildcard IP network wildcard operator eq It gt range port An integer 1 65535 destination ip IP network destination wildcard IP network wildcard precedence mandatory optional 102 Avaya X330W 2DS1 User s Guide Policy CLI Commands Example Router N gt ip access list 101 23 deny ip any 1 2 0 0 0 0 255 255 X330WAN 2DS1 1 super ip access list 101 23 deny ip any 0 10 0 0 0 0 255 255 X330WAN 2DS1 1 super ip access list 101 24 fwd3 udp any host 0 1 1 1 range 20 23 optional X330WAN 2DS1 1 super ip access list 101 25 permit tcp any any eq 23 established ip access list cookie Use the ip access list cookie command to set the list cookie for a specific policy list The syntax for this command for the X330WAN is ip access list cookie lt list id gt lt cookie gt policy li
107. lock source Use the controller command to enter the specified controller s mode Note You cannot configure one controller as E1 and the other as T1 The syntax for this command is controller el t1 lt port gt el This is an E1 port t1 This is a T1 port port The number of the port that is being configured Example X330WAN 2DS1 1 configure controller E1 2 description Controller context Use the description command to set the description of the E1 T1 interface This description appears both in the ifAlias and the circuitIdentifier MIB values for that interface Use the no form of this command to remove the Avaya X330W 2DS1 User s Guide 125 Chapter 7 X330WAN CLI Commands controller s description Note This command can also be executed from the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no description lt desc gt desc A string describing the E1 T1 interface The string may contain blanks and is up to 255 characters long Examples X330WAN 2DS1 1 config controller 1 description E1 controller X330WAN 2DS1 1 config controller 1 no description description Interface context ds mode Use the description command to set the description of the interface Use the no form of this command to remove the interface s description Note This command can also be executed from the
108. ls to transmitting hosts stating that the bandwidth is limited and that they should reduce their transmission speed RTP Header Compression The Real Time Protocol RTP is the basis of common VolP traffic RTP runs over UDP and incurs a 12 byte header on top of other IP UDP headers Running on PPP or Frame Relay this protocol can be compressed X330WAN RTP Header Compression process is based on the fact that the packet order on a PPP link is preserved As a result many times only the deltas from the previous packet s header needs to be sent and not the full header Moreover since the deltas are often constant the second order delta is 0 and does not need to be transmitted In many cases all three headers IP UDP RTP 40 bytes can be reduced to a size of 2 4 bytes Fragmentation and Reassembly the X330WAN supports Fragmentation of IP packets according to RFC 791 Reassembly of IP packets destined only to the X330WAN i e packets that have its IP address as their destination address Fragmented IP packets with destinations other than this X330WAN will NOT be reassembled by this X330WAN Avaya X330W 2DS1 User s Guide Features Reassembly is associated with the following user configurable parameters The number of maximum possible concurrent reassembled packets Min 0 Max 200 Default 100 The time in seconds to wait for a packet to be reassembled Min 5 Max 120 Defa
109. lt area id gt net addr IP address wildcard mask Wildcard mask address area id Area ID This parameter exists for compatibility with the P550 86 Avaya X330W 2DS1 User s Guide Layer 3 CLI Commands Examples X330WAN 2DS1 1 configure router ospf network 192 168 0 0 X330WAN 2DS1 1 configure router ospf network 192 168 0 0 0 0 255 255 area 0 0 0 0 network Router RIP Context ping Use the network command to specify a list of networks on which the RIP is running The no form of this command removes an entry The syntax for this command is no network lt ip address gt lt wildcard mask gt ip addr The IP address of the network of directly connected networks wildcard mask Wildcard mask address Exists for compatibility with P550 Example To specify that RIP will be used on all interfaces connected to the network 192 168 37 0 X330WAN 2DS1 1 configure router rip network 192 168 37 0 Use the ping command to check host reachability and network connectivity The syntax for this command is ping lt host gt lt interval gt lt size gt timeout source address host IP address of the target system interval An integer the number of seconds between successive ping messages The default is 1 second size An integer the size of the packet sent during a ping operation The default is 50 bytes timeout Timeout in seconds 1 10 source address IP address
110. mber of packets successfully reassembled Fail Number of packets which failed to be reassembled Overflow Number of packets which overflowed the fragment database The syntax for this command is show fragment Example X330WAN 2DS1 1 configure show fragment show interfaces Max number of concurrently reassembled packets is 100 Max number of fragments per packet is 64 Fragment timeout is 10 sec Number of packets waiting to be reassembled is 0 Number of successfully reassembled packets is 11954 Number of packets which failed to be reassembled is 0 Number of packets which overflowed the database is 0 Use the show interfaces command to display information on all interfaces in the X330WAN starting at the first Layer 2 interface If the type is specified only interfaces of that type are shown If no type is specified all interfaces are shown 144 Avaya X330W 2DS1 User s Guide WAN CLI Commands The syntax for this command is show interfaces lt type gt lt identifier gt type The type of this interface Select one of the following FastEthernet Serial FabricFastEthernet Loopback Console identifier e Fora FastEthernet interface An integer 1 e Fora Serial interface lt port gt lt channel group gt lt port gt Either 1 or 2 lt channel group gt For E1 an integer 0 30 For T1 an integer 0 23 For a FabricFastEthernet interface 1 lt vlan gt lt vlan gt An int
111. n where the WAN traffic goes through the X330WAN module out to an external firewall and or VPN and then enters the LAN Figure 4 3 X330WAN with Security Avaya P330 Switch with X330WAN Internet Firewall The following configuration file is a result of configuring the X330WAN as shown in Figure 4 3 controller t1 1 channel group 12 timeslots 1 31 H controller t1 2 interface FabricFastEthernet 1 shutdown interface FastEthernet 1 ip address 135 20 7 8 255 255 0 0 l interface Serial 1 12 encapsulation ppp ip address 194 49 1 249 255 255 255 252 ip routing mode RT_PRIMARY_MGMT 32 Avaya X330W 2DS1 User s Guide Chapter 5 Troubleshooting This chapter provides an explanation of how to troubleshoot operational difficulties with the X330WAN Troubleshooting the X330WAN should be performed according to layers When a problem appears you should start isolating it by troubleshooting Layer 1 the controller s alarms and errors first then Layer 2 and finally Layer 3 Monitoring Traffic You can monitor the state of the X330WAN s E1 T1 ports using the show controllers command The command can be entered via the CLI The resulting output provides information about the state of the E1 T1 controller and reports alarms In addition the output provides statistics on the state of the controller over the last 24 hour period To receive output for
112. n_violation traps to a specific manager X330WAN 2DS1 1 super set snmp trap 192 168 173 42 disable vlan violation SNMP vlan violation traps disabled 54 Avaya X330W 2DS1 User s Guide General Device Commands Output Example To add an entry in the SNMP trap receiver table with default X330WAN 2DS1 1 super set snmp trap 192 168 173 42 SNMP trap receiver added set snmp trap auth Use the set snmp trap auth commands to enable disable the sending of SNMP traps upon SNMP authentication failure The syntax for this command is set snmp trap enable disable auth Output Example X330WAN 2DS1 1 super set snmp trap enable auth Authentication trap enabled set system contact Use the set system contact command to set mib2 system contact MIB variable The syntax for this command is set system contact contact string contact string Contact person The contact person field is cleared if this field is blank A string of 2 words or more must be type in quotation marks e g Yigdal Naouri Example set system contact Gabby ext 545 set system location Use the set system location command to set the mib2 system location MIB variable Avaya X330W 2DS1 User s Guide 55 Chapter 7 X330WAN CLI Commands The syntax for this command is set system location location string location string Location name The location name is cleared if this field is left blank A string of 2
113. nal a terminal emulator or a modem The serial port on the front panel is labelled Console and has an RJ 45 connector Connect the X330WAN module to a terminal or a terminal emulator using the supplied Console cable and the RJ 45 to DB 9 adaptor To connect a modem use the supplied cable and an RJ 45 to DB 25 adaptor Avaya X330W 2DS1 User s Guide 19 Chapter 3 Initial Configuration Note The cable and two adaptors can be found in the Avaya P330 accessory set and they are clearly marked Console Pin Assignments For direct Console communications connect the X330WAN to the Console Terminal using the supplied RJ 45 crossed cable and RJ 45 to DB 9 adapter The following table shows the pinout from the X330WAN RI AS connector to both a DB 9 and DB 25 connector Table 3 1 Pinout of the Required Connection for Console Communications X330WAN RJ 45 Pin Name ee SE 1 For future use NC See note 2 TXD 3 3 P330 input 3 RXD 2 2 P330 output 4 CD 4 8 5 GND 5 7 6 DTR 1 20 7 RTS 8 4 8 CTS 7 5 D Note Pin 1 of the Modem DB 25 connector is internally connected to Pin 7 GND 20 Avaya X330W 2DS1 User s Guide Configuring the X330WAN Configuring the X330WAN An X330WAN can be configured using the Command Line Interface CLI utility the built in Avaya P330 Device Manager Embedded Web or Avaya MultiService Network Manager For instructions on using
114. nel group command to create a channel group also referred to as det bundle A channel group can be the underlying interface for a PPP session This command creates a logical interface which is identified by a port number a colon and a channel group number For example channel group 8 on E1 port 2 would be referred to as 2 8 in all places where a channel group is needed as a parameter The syntax for this command is channel group lt channel num gt timeslots lt timeslot list gt speed 56 64 Note The Speed option can be performed only when the controller is set to T1 channel num ID number to identify the channel group The valid range is from 0 to 23 for T1 lines and from 0 to 30 for E1 lines timeslot list Timeslots DSOs to include in this channel group The valid timeslots are e 1 to 24 for T1 e 1to 31 for El Values can be either separated by a to indicate a mu list or a to indicate a range speed Acceptable values are 56 or 64 Avaya X330W 2DS1 User s Guide 123 Chapter 7 X330WAN CLI Commands CG Note If the user has an active ppp session over this channel group a warning is issued Note If a user issues this command with an existing channe1 nunm it is assumed that the timeslot list is a list of timeslots that should replace the current list of timeslots already defined for that channel group Note Channel groups voice groups and TDM groups all use gr
115. ng it manually 1 Installing from the Avaya P330 Documentation and Utilities CD 1 Close all unnecessary applications on your PC Insert the Avaya P330 Documentation and Utilities CD into the CD drive Click Start on the task bar Select Run Type x emweb aux files plug in_1_3_1 02 exe where xis the CD drive letter 6 Follow the instructions on screen oar wn 2 Install from the Avaya Site Click link in the Welcome page 3 Install from your Local Web Site Click link in the Welcome page Note This option is only available if the network manager has placed the files on the local Web server 42 Avaya X330W 2DS1 User s Guide Installing the On Line Help and Java Plug In on your Web Site Installing the On Line Help and Java Plug In on your Web Site D Note This procedure is optional Copying the help files and Java plug in to a local Web server allows users to access the on line help for the Embedded Manager and enables automatic installation of the Java plug in the first time the users tries to manage the device 1 Copy the emweb aux files directory from the Avaya P330 Documentation and Utilities CD to your local Web server Please refer to your Web server documentation for full instructions 2 Define the URL in the Avaya P330 using the following CLI command set web aux files url IP address directory name where IP address directory name is the location of the directory from the previous step
116. ng major traffic paths e WAN to LAN external The X330WAN can route WAN traffic through a firewall and or a Virtual Private Network e WAN to LAN internal The X330WAN can route WAN traffic directly to from the LAN Front Panels and LEDs This section illustrates the front panels of the various available X330WAN access router modules and describes their LED functions An X330WAN front panel contains LEDs WAN and Ethernet connectors and a console connector The status LEDs provide at a glance information The front panel LEDs consist of Port LEDs which display information for each port 10 Avaya X330W 2DS1 User s Guide Front Panels and LEDs X330W 2DS1 Front Panel On the front panel of the X330W 2DS1 there is a column of four LEDs for each port in the access router module Figure 1 4 X330W 2DS1 Front Panel Vid zen X330WAN LEDs The following table describes of the LEDs on the front panel of the X330WAN Table 1 1 X330WAN LED Descriptions LED Name Color Description LED Status ALM Red Alarm ON The port is reset or an E1 T1 alarm condition is present OFF Initialization is successful and the software is running correctly TST Green Test ON Port is being initialized or loopback is active OFF Port initialization completed and loopback is not active ACT Yellow Active ON At least one PPP session is active OFF
117. nges to X33 OWAN 2DS1 N super if Loopbackn where N is the switch number and o is the loopback interface number 2 Usethe ip address lt ip address gt lt mask gt command to assign an IP address and subnet mask to the interface 3 Type exit to return to Supervisor mode The prompt returns to X33 OWAN 2DS1 N super Note For the first inteface to be configured the following message appears The primary management interface has changed For this change to take effect you need to copy running config startup config and then reset the device You need to issue the copy running config startup config and reset commands Note You cannot delete an interface if there is a primary management IP PMI defined on it Checking the Loopback Fast Ethernet T1 E1 IP Interface Configuration After configuring the new interface you can perform the following tests to verify that the new interface is operating correctly e Usethe show ip interface lt interface name gt lt IP interface gt lt ip address gt command to display IP interface configured serial and Ethernet ports e Use the show controllers lt port gt command to display the status of the controller for T1 E1 interfaces e Usethe show interfaces lt type gt lt identifier gt command to display information on all interfaces Fast Ethernet Fabric Serial Console and 26 Avaya X330W 2DS1 User s Guide Configuring the X330 WAN Lo
118. ommunity String read only public read write public trap public EE Eet duplicate ip ip vlan violation CCCa AC show startup config show system Use the show startup config command to show the NVRAM based configuration loaded automatically at startup The syntax for this command is show startup config Use the show system command to display the up time system name location and contact person The syntax for this command is show system Output Example X330WAN 2DS1 1 super show system Uptime d h m s 0 2 40 55 System Name System Location System Contact 60 Avaya X330W 2DS1 User s Guide General Device Commands P332 version 3 0 5 Alpha LAB Ygdal Naouri show tftp download software status Use the show tftp download software status commands to display the status of the current TFTP Device Manager S W Embedded Web download process into the device The syntax for this command is show tftp download software status Output Example X330WAN 2DS1 1 super show tftp download software status Module 1 Module SZ Source file d p340sw gt m1 3 5 18 p340 web Destination file EW Archive Host 149 49 70 61 Running state Writing Failure display null Last warning No warning show tftp download upload status Use the show tftp download status and show tftp upload status commands to display the status of the current TFTP configuration file copy process into from th
119. on 192 168 7 8 to the ARP cache Router configure arp 192 168 7 8 00 40 0d 8c 2a 01 To remove an entry to the ARP cache for the station 192 168 13 76 Router configure no arp 192 168 13 76 arp timeout Use the arp timeout command to configure the amount of time that an entry remains in the ARP cache To restore the default value 14400 use the no form of this command The syntax for this command is arp timeout lt seconds gt The syntax for the no form of this command is no arp timeout seconds The amount of time in seconds that an entry remains in the arp cache Max value is 604800 Examples To set the arp timeout to one hour X330WAN 2DS1 1 configure arp timeout 3600 To restore the default arp timeout 64 Avaya X330W 2DS1 User s Guide Layer 3 CLI Commands Router N configure no arp timeout clear arp cache Use the clear arp cache command to delete all dynamic entries from the ARP cache and the IP route cache The syntax for this command is clear arp cache lt vlan gt lt ip addr gt lt mask gt vlan VLAN string up to 16 characters or VLAN ID number ip addr IP address mask IP mask Examples clear arp cache Flush all ARP entries clear arp cache marketing_vlan Flush ARP entries for a VLAN clear arp cache 30 Flush ARP entries for a VLAN ID clear arp cache 192 168 0 0 255 255 0 0 Flushrange of ARP entries belonging to one subnet clear ip route Use the clear ip route command to delete all the
120. ontext Use the timers basic command to set RIP timers The no form of this command to set the RIP timers to their default The syntax for this command is no timers basic lt update gt lt invalid gt update RIP update timer in seconds invalid RIP invalid route timer in seconds Avaya X330W 2DS1 User s Guide 99 Chapter7 X330WAN CLI Commands Example X330WAN 2DS1 1 configure router rip timers basic 30 180 timers spf Router OSPF context Use the timers spf command to configure the delay between runs of OSPF s SPF calculation Use the no form of this command to restore the default 3 seconds The syntax for this command is no timers spf lt spf holdtime gt spf holdtime The time in seconds of the delay between runs of OSPF s SPF calculation The range of acceptable values is 1 to 3600 Example X330WAN 2DS1 1 super timers spf 5 traceroute Use the traceroute command as a trace route utility The syntax for this command is traceroute lt host gt host IP address Example X330WAN 2DS1 1 super traceroute 192 168 50 13 100 Avaya X330W 2DS1 User s Guide Policy CLI Commands Policy CLI Commands This section contains a list of all Policy related CLI commands ip access default action Use the ip access default action command to set the default action for a specific policy list The syntax for this command is ip access default action lt policy list num
121. oopbackZ Loopback Interface Serial X330WAN 2DS1 N config if Serialn x N is the number of the device in a stack of WAN devices n is the number of the WAN port OUT or 2 Z is the interface number and x is the number of the channel group 46 Avaya X330W 2DS1 User s Guide General Device Commands General Device Commands This section contains a list of all general device CLI commands clear screen The clear screen command clears the current terminal display The syntax for this command is clear screen clear snmp trap Use the clear snmp trap command to clear an entry from the SNMP trap receiver table The syntax for this command is clear snmp trap lt rcvr_addr gt all revr_addr IP address or IP alias of the trap receiver the SNMP management station to clear all Keyword that specifies every entry in the SNMP trap receiver table Output Example X330WAN 2DS1 1 super clear snmp trap 192 122 173 82 SNMP trap receiver deleted clear timezone Returns the timezone to its default Coordinated Universal Time UTC The syntax for this command is clear timezone copy running config startup config Use the copy running config startup config command to copy the device configuration from the current RAM Running Configuration to the Startup Configuration NVRAM The syntax for this command is copy running config startup config Avaya X330W 2DS
122. opback Verify that the output information is correct e Use the show running config command to display the configuration running on the switch e Use the show startup config command to display the configuration loaded at startup e Use the ping lt host gt lt interval gt lt size gt command to send ICMP echo request packets to another node on the network Each node is periodically pinged and checked if an answer was received This checks host reachability and network connectivity Saving Your Configuration It is advisable to save your configuration KS Note Your configurations are lost after each reset or after a power failure To save your configuration type copy running config startup config This copies your X330WAN configuration from the current VRAM Running Configuration to the Startup Configuration NVRAM Establishing a Telnet Connection Perform the following steps to establish a Telnet connection to the X330WAN for configuration of WAN parameters Telnet directly to one of the Router IP addresses 1 Connect your station to the network 2 Verify that you can communicate with the X330WAN using the ping lt host gt lt interval gt lt size gt command to the IP of the X330WAN If there is no response check the IP address and default gateway of both the X330WAN and the station 3 From the Microsoft Windows taskbar of your PC click Start and then Run or from the DOS prompt of your PC then start
123. or this command is sync time Output Example X330WAN 2DS1 1 super sync time Time has been distributed tech Use the tech command to enter tech mode This command is reserved for service personnel use only terminal length Use the terminal length command to set the length of the terminal display in characters The syntax for this command is terminal length lt screen length gt screen length none Displays the current length number Set the new screen length Example X330WAN 2DS1 1 super terminal length 24 terminal width Use the terminal width command to set the width of the terminal display in characters The syntax for this command is terminal width lt character gt character none Displays the current width number Set the new screen width Example X330WAN 2DS1 1 super terminal width 6 Avaya X330W 2DS1 User s Guide 63 Chapter 7 X330WAN CLI Commands Layer 3 CLI Commands This section contains a list of all Layer 3 related CLI commands arp Use the arp command to add a permanent entry to the Address Resolution Protocol ARP cache The no form of this command removes an entry either a static entry or a dynamically learned entry The syntax for this command is no arp lt ip address gt lt mac address gt ip address IP address in dotted decimal format of the station mac address MAC address of the local data link Examples To add a permanent entry for stati
124. ote end AlS Blue Definition Alarm Indication Signal Local Rx line is down The administrator of the remote module cut your line The alarm severity is Major Avaya X330W 2DS1 User s Guide 35 Chapter 5 Using Loopbacks Indication The alarm is indicated when the ALM LED lights up or by using the show controllers command from the CLI For more information refer to Monitoring Traffic on page 33 Corrective Actions e Call the administrator of the remote module e Wait for the signal to return Alarm Detection Alarms can be identified on the X330WAN either using the LEDs on the front panel or using the CLI The X330WAN front panel LEDs can indicate two types of Local Alarms e Ifa LOS is sensed by a E1 T1 port its SIG LED will be off and the ALM LED will be on e When all other alarms are sensed by a E1 T1 port the ALM LED will light In addition an Alarm condition will be indicated by a message on the CLI screen mp for example Controller T1 1 changed state to down LOS More detailed information about alarms can be obtained using the show controllers CLI command Using Loopbacks The X330WAN supports the following Loopback types e Diag Loopback E1 T1 The X330WAN CPU instructs the Line Framer to create a loop towards the CPU A Blue Alarm AIS is sent on the line to the peer module e Local Line Loopback E1 T1 The X330WAN Line Framer creates a loop on the line towards the other
125. oup numbers All D group numbers configured for channel groups voice groups and TDM groups must be unique For example you cannot use the same group number for a channel group and a TDM group Examples X33 0WAN 2DS1 config controller 1 channel group 10 timeslots 10 24 X330WAN 2DS1 1 config controller 1 channel group 2 timeslots 5 6 8 20 24 clear fragment Use the clear fragment command to clear the fragment database and restore its defaults Note No fragmentation will be done of packets in transit through the router The syntax for this command is clear fragment clock source Controller Context Use the clock source command to configure the clock source for an E1 T1 controller Use the no form of this command to return the value to the default 124 Avaya X330W 2DS1 User s Guide WAN CLI Commands controller The syntax for this command is no clock source line internal line The controller recovers the external clock from the line and provides the recovered clock to the internal system clock generator This is the default value internal The controller synchronizes itself to the internal system clock Note Only one E1 T1 controller at a time can recover the network clock and distribute it to the internal clock generator Examples X330WAN 2DS1 1 config controller 1 clock source internal X330WAN 2DS1 1 config controller 1 no c
126. ow ip distribution access lists command to display the content of all current distribution lists or of a specific list The syntax for this command is show ip distribution access lists lt distribution list number gt distribution list number The distribution list number An integer from 1 to 99 Example To display the content of distribution list number 1 X330WAN 2DS1 1 configure show ip distribution access lists 1 Example To display the content of all current distribution lists X330WAN 2DS1 1 configure show ip distribution access lists show line console Use the show line console command to display the console interface The syntax for this command is show line console 146 Avaya X330W 2DS1 User s Guide WAN CLI Commands Output Example X330WAN 2DS1 1 configure show line console Console ppp state disable Asynchronic mode terminal Baud rate is 38400 Timeout is 0 ppp authentication none show logout Use the show logout command to display the CLI logout The syntax for this command is show logout Output Example X330WAN 2DS1 1 configure show logout CLI timeout is 15 minutes show queueing Use the show queueing command to display the priority queue size in packets The syntax for this command is show queueing lt interface type gt lt identifier gt interface The type of this interface Select one of the following type FastEthernet Serial Fabric
127. ownloaded to complete the plug in installation e Retrieve it from here After download is complete run the executable you have downloaded to complete the plug in installation Install it from the Documentation CD provided with the P330 Device Refer to the User s Guide for details on how to install the plug in on a local web server Done 1 1 E internet 40 Avaya X330W 2DS1 User s Guide Running the Embedded Manager Ifyou have the Java plug in installed the Web based manager should open in a new window see Figure 6 2 Figure 6 2 Web based Manager PPP Sessions Alias dfgd Serial 1 0 chgfdhgf Serial 1 1 ml d E V ft H CM wan CH Cu Num E CN Ifyou do not have the Java plug in installed follow the instructions on the Welcome page that offer a variety of options to install the plug in see Figure 6 1 or see Installing the Java Plug in on page 42 Avaya X330W 2DS1 User s Guide 41 Chapter 6 Embedded Web Manager Installing the Java Plug in If the network manager has configured the system the plug in should be installed automatically Note Ensure that Java or JavaScript is enabled on your Web browser Please refer to your browser on line help or documentation for further information If the plug in is not installed automatically then you have three options for installi
128. peer module e Local Payload Loopback E1 T1 The X330WAN Line Framer creates a loop through itself and re frames the signal on its way back from the peer module e Remote Line Loopback T1 only The X330WAN sends the remote peer module a request to create a line loop A Line Loopback signal is used to indicate the request e Remote Payload Loopback T1 only The X330WAN sends the remote peer module a request to create a loop through its Line Framer A Payload Loopback signal is used to indicate the request The Remote Payload Loopback type is only available in ESF framing To instruct the X330WAN to perform a loopback use the loopback diag loopback local and loopback remote command For more information about these commands see Chapter 7 X330WAN CLI Commands 36 Avaya X330W 2DS1 User s Guide Troubleshooting VoIP Transmission Troubleshooting VoIP Transmission To enable VoIP the following must be configured on the devices at both ends of the connection e VoIP must be enabled on both ends e The RTP port range must be the same on both ends e The devices on both ends must be configured according to the running voice applications When the device on the other end is a non Avaya device e Configure the non Avaya device for the maximum amount of connections 255 e Configure the port range of the Avaya device to 49152 65535 e Configure the non ietf working mode using the command ip rtp non tcp mode Avay
129. pport and download it according to the instructions found in the User s Guide that accompanies your Avaya P330 switch You can see the firmware version of your Avaya switch using the show image version command Avaya X330W 2DS1 User s Guide 13 Chapter 2 Installation Installing an X330WAN Module into an Avaya P330 Switch Note Like all other P330 expansion modules the X330WAN modules are NOT hot swappable Removing inserting an X330WAN with the power on resets the enclosing P330 switch To install an X330WAN access router module 1 Remove the blanking plate or other sub module from the P330 switch assigned to house the X330WAN module if there is one installed 2 Insert the X330WAN module gently into the slot ensuring that the lower printed circuit board PCB is aligned with the guide rails The PCB not the metal base plate fits into the guide rail 3 Press the X330WAN module in firmly until it is completely inserted into the P330 switch If the module is not inserted completely the P330 switch will not successfully reset 4 Gently tighten the two screws on the front panel of the access router module Note The Avaya P330 switch must not be operated with the expansion slot open The expansion slot should either include a sub module or be covered with the supplied blanking plate 5 Power up the P330 switch 6 Follow the post installation checks as described in Power On Self Test below Power
130. r 40 Installing the Java Plug in 42 Installing the On Line Help and Java Plug In on your Web Site 43 Documentation and Online Help 43 Software Download 43 Chapter 7 X330WAN CLI Command cccccscsecsssrsessecscssessessecscessesessesesessessesssssessesees 45 Introduction About CLI 45 X330WAN CLI Prompts ENEE 46 General Device Commands 47 rel EE NESTE EE 47 clear simp trap cessera nanana n 47 clear timezone target iar e a 47 copy running config startup config se sessssssetssstesrtesterttesseenteess 47 COPY Tunming Config ftp niceai naiean iaaa ikaita 48 copy startu p config thtp s ni ieta Ee AR S S 48 Copy tftp startup COMfIg ENEE 48 Copy tftp EW atchiv geed 49 COPY ttp EE 49 Ce i E EE E EOE E E EEEE 50 GE 51 SOL TIME AEO ege eege deed E E 51 ele ee TEEN 51 ue BT ER EE 52 t ek EA KE 52 TOSOE Drees askance ee Eege ee 52 Avaya X330W 2DS1 User s Guide iii Contents SEL DOOE Dank ziminea liaise doeed ech Ae a a e a E 53 Set 1OSOUE EE 53 Set SKMP tap ieri e are lest tre O EE ale den tahini 54 s t Simp trap auth esiereeeetedeegeeb eegeeel eieiei 55 Set SYSTEM CONLACE aeie eiee E A oa a oa iaee E 55 EE te 55 Set SYSTEM Dame 2 c cssescevenesentereetsseedsneessobeteneesssessetonssaeesekdetsdised etsnees 56 SEL TIMES CSN GE 56 Set TIME Protocol giessen Eet EEN 56 SOU TIME SCLVET Beete ee ed et ee Ee 57 SOU imene einernie Eege EE evden eee od Bites 57 SHOW boot bank sra eessen eeh eseu eege e
131. r is sending remote alarm Receiver has loss of signal Framing is SF Line Code is AMI Clock Source is Line channel group 1 timeslots 1 6 Data in current interval 347 seconds elapsed D Line Code Violations 0 Path Code Violations 0 Slip Secs 0 Fr Loss Secs 0 Line Err Secs 0 Degraded Mins 0 Errored Secs 0 Bursty Err Secs 0 Severely Err Secs 0 Unavail Secs Total Data last 24 hours 0 Line Code Violations 0 Path Code Violations 0 Slip Secs 0 Fr Loss Secs 0 Line Err Secs 0 Degraded Mins 0 Errored Secs 0 Bursty Err Secs 0 Severely Err Secs 0 Unavail Secs Note When this command is used with the port parameter information about all statistics intervals is displayed 140 Avaya X330W 2DS1 User s Guide WAN CLI Commands The following are the show controllers command output fields Field T11is down Cablelength Remote alarm Framing Line Code Clock Source Channel Group Data in current interval 347 seconds elapsed Line Code Violations Description Displays that the T1 controller 1 is not operating The controller s state can be up down or administratively down Loopback conditions are shown either as being locally looped or remotely looped Displays the current line buildout Relevant for T1 lines only Any alarms detected by the controller are displayed The possible alarms are e Transmitter is sending remo
132. ress of the routes mask The ip mask of the routes Examples show ip route static Display all static routes show ip route static 137 32 50 13 Display a single static route show ip route static 137 44 50 13 255 255 255 0 Display range of static routes Output Example Router 1 super show ip route static X330WAN 2DS1 1 super router ospf show ip route static Showing 1 rows Network Mask Interface Next Hop Cost Pref Perm Active 0 0 0 0 0 FastEth 1 149 49 75 1 1 low No Yes show ip route summary Use the show ip route summary command to display the number of routes known to the device The syntax for this command is show ip route summary Output Example X330WAN 2DS1 1 super router ospf show ip route summary X330WAN 2DS1 1 super show ip route summary Route Source Networks Subnets Local 0 Static 0 Total 0 Use the show ip vrrp command to display VRRP information Avaya X330W 2DS1 User s Guide 97 Chapter7 _X330WAN CLI Commands The syntax for this command is show ip vrrp lt vlan gt router id lt vr id gt detail vlan Filter by Fabric router id Filter by virtual router ID 1 255 vr id The virtual router ID detail Provide detailed information Output Example X330WAN 2DS1 1 configure show ip vrrp VRRP is globally enabled VLAN VRID IP Address Pri Timer State Since 1 192 168 66 23 255 if MASTER 00 00 00 2 192 168 66 24 100 1 BACKUP 00 00 00 show ip vrrp detail Use the
133. rmed if the controller is set to T1 2 This command is used only when the fd1 at amp t option is defined 138 Avaya X330W 2DS1 User s Guide WAN CLI Commands The syntax for this command is remote lt fdl request type gt fdl request Reset Performance Monitoring Counters Reset Errorred ESF type Data Example X330WAN 2DS1 1 super remote Reset errored ESF data show controllers Use the show controllers command to display the status of the controller The syntax for this command is show controllers lt port gt port The port number Example X330WAN 2DS1 1 configure show controllers Output Example E1 1 is up No alarms detected Framing is CRC4 Line Code is HDB3 Clock Source is Line channel group 1 timeslots 1 31 Data in current interval 778 seconds elapsed 0 Line Code Violations 0 Path Code Violations 0 Slip Secs 0 Fr Loss Secs 0 Line Err Secs 0 Degraded Mins 0 Errored Secs 0 Bursty Err Secs 0 Severely Err Secs 0 Unavail Secs Total Data last 92 15 minute intervals 19958 Line Code Violations 38 Path Code Violations 0 Slip Secs 5 Fr Loss Secs 6 Line Err Secs 0 Degraded Mins Avaya X330W 2DS1 User s Guide 139 Chapter 7 X330WAN CLI Commands 6 Errored Secs 1 Bursty Err Secs 5 Severely Err Secs 0 Unavail Secs E1 2 is administratively down Output Example T1 1 is down Cablelength is long gain26 Odb Transmitte
134. rnet 1 l interface Serial 1 12 encapsulation ppp ip address 194 49 1 249 255 255 255 252 ip routing mode RT_PRIMARY_MGMT 30 Avaya X330W 2DS1 User s Guide Connecting a Small Office to the Internet Connecting a Small Office to the Internet A small office requires a reliable and fast connection to the Internet to maintain fast communication times and have access to information on the World Wide Web The following figure shows a typical configuration of the network connecting a small office to the Internet Figure 4 2 Small Office to the Internet E Avaya P330 Switch a with X330WAN BR Ge e 136 2078 104 490 255 255 0 0 194 49 0 a 255 255 0 0 PEF Over T E1 T1 I Firewall The following configuration file is a result of configuring the X330WAN for the network shown in Figure 4 2 controller t1 1 channel group 12 timeslots 1 31 controller t1 2 interface FabricFastEthernet 1 shutdown interface FastEthernet 1 ip address 135 20 7 8 255 255 0 0 interface Serial 1 12 encapsulation ppp ip address 194 49 1 249 255 255 255 252 ip routing mode RT_PRIMARY_MGMT Avaya X330W 2DS1 User s Guide 31 Chapter 4 Common Configurations Using the X330WAN with Security There are different ways of connecting the X330WAN modules to provide security to the local network Figure 4 3 shows a typical configuratio
135. s PPP should allow for negotiation of a network layer protocol If no network protocol is negotiated within the given time the connection is terminated An integer from 1 to 65535 Example X330WAN 2DS1 1 config if Serial1l 1 ppp timeout ncp 10 Avaya X330W 2DS1 User s Guide 137 Chapter 7 X330WAN CLI Commands ppp timeout retry Serial interface context Use the ppp timeout retry command to set the maximum time in seconds to wait for a response during PPP negotiation Use the no form of this command to restore the maximum time to wait for a response during PPP negotiation to the default value 2 seconds The syntax for this command is no ppp timeout retry lt Seconds gt Seconds The maximum time in seconds to wait for a response during PPP negotiation An integer from 1 to 255 Example X330WAN 2DS1 1 config if Seriall 1 ppp timeout retry 10 queue limit Serial interface context Use the queue 1imit command to set the packet size of the various queues The syntax for this command is no queue limit lt queue id gt lt size gt queue id The queue priority ID 1 highest 4 lowest size The size in packets of the queue The total amount of packets in all queues cannot exceed 500 Example X330WAN 2DS1 1 config if Serial1l 1 queue limit 1 200 remote Controller context Use the remote command to reset the far end counters Note ER 1 This command can only be perfo
136. spf command to enable OSPF protocol on the system and to enter the Router Configuration context The no form of this command disables it globally The default is disabled The syntax for this command is no router ospf Use the router rip command to enable the Routing Information Protocol RIP and to emter tje Router Configuration context The no form of this command disables RIP The default state is disabled The syntax for this command is no router rip Example To enable the RIP protocol X330WAN 2DS1 1 configure router rip X330WAN 2DS1 1 configure router rip Use the router vrrp command to enable VRRP routing globally Use the no form of this command to disable VRRP routing Note You cannot activate both VRRP and SRRP protocols at the same time The syntax for this command is no router vrrp Use the show ip arp command to display the Address Resolution Protocol ARP cache The syntax for this command is show ip arp lt interface gt lt IP interface gt lt ip addr gt xip mask gt static interface String up to 32 characters Avaya X330W 2DS1 User s Guide 89 Chapter 7 X330WAN CLI Commands IP interface ip addr ip mask static Examples show show show show show show ip ip ip ip ip ip arp arp arp arp arp arp String up to 32 characters The IP address of the station s The IP mask of the routes Display static IP ARP informat
137. st number An integer 100 199 list id An integer 100 149 where 0 is the default list cookie An integer Example X330WAN 2DS1 1 super ip access list cookie 101 12345 ip access list copy Use the ip access list copy command to copy a configured source policy list to a destination policy list The syntax for this command is ip access list copy lt source list gt lt destination list gt source list An integer 100 199 or for the X330WAN 100 149 where 0 is the default list destination list An integer 100 199 or for the X330WAN 100 149 Example X330WAN 2DS1 1 super ip access list copy 100 101 Avaya X330W 2DS1 User s Guide 103 Chapter 7 X330WAN CLI Commands ip access list dscp operation Use the ip access list dsc operation command to set a DSCP to action Note This command is only supported by the P333R LB device and X330WAN module The syntax for this command is ip access list dscp operation lt policy list number gt lt dscp gt lt action gt policy list number An integer 100 199 or for the X330WAN 100 149 where 0 is the default list dscp Range of DSCP action Action name Example X330WAN 2DS1 1 super ip access list dscp operation 101 9 16 fwd3 ip access list dscp name Use the ip access list dscp name command to set a DSCP name Note This command is only supported by the P333R LB device and X330WAN module The syntax for this command is
138. t Example X330WAN 2DS1 1 config if FastEthernet1 ip simulate 100 in 192 67 85 12 193 76 54 25 no ip composite op Use the no ip composite op command to delete a composite operation from a policy list CG Note This command is only supported by the X330WAN module The syntax for this command is no ip composite op monitor lt policy list number gt lt composite operation index gt policy list number An integer 100 149 where 0 is the default list composite operation index Index of operation in the table to be deleted Indices 0 12 can not be deleted Example X330WAN 2DS1 1 configure no ip composite op 101 15 no ip distribution access list Use the no ip distribution access list command to delete a distribution list statement CG Note This command is only supported by the X330WAN module The syntax for this command is no ip distribution access list lt access list number gt 114 Avaya X330W 2DS1 User s Guide Policy CLI Commands lt access list index gt access list number An integer 1 99 access list index An integer Examples X330WAN 2DS1 1 configure no ip distribution access list 1 X330WAN 2DS1 1 configure no ip distribution access list 2 25 EN Note If a list index is not given the no ip distribution access list all rules will be deleted set qos policy source Use the set qos policy source command to set the policy source The de
139. t Interface context oo cee eeteeeeees 72 Ip Metmask fOrmMat ENEE 73 ip ospf authentication key Interface context 0 cece 73 ip ospf cost Interface context seccceesesestetescecesesesteteeeseeeeteeseeeenes 74 ip ospf dead interval Interface context occ teens 74 ip ospf hello interval Interface Mode ccccesceeeteteeeseeteteeeeees 74 ip ospf priority Interface Mode ENEE 75 ee Te EE 75 ip proxy arp Interface context occ ceeesesesteteteeseseeneeneeeees 76 ip redirect Interface context ENEE 76 ip rip authentication key Interface context cee teens 77 ip rip authentication mode Interface context 0 eee 77 ip rip default route mode Interface context oe eee 78 ip rip poison reverse Interface Context oes cece seeeeenens 78 ip rip rip version Interface context oes ee eects tees te teeeeees 79 ip rip send receive Interface contexte 79 ip rip split horizon Interface Context ee 80 Us 81 Ip TOULNG EE 82 ip routing mode Interface Context nee 82 ip vrrp Interface Context ENEE 82 gn Ee EE 83 ip virp auith key isingit sitini sai iaee 83 ip vrrp override addr Owner s ssssssssississsssissississessresiesiesessresieseesee 84 IP VITP preempt euer dee E e E ES 84 DIETERLEN eieaa et e E E E N EE E 85 ip Vip priority EE 85 DEER 86 network Router OSPF context oo ceeceeeeeseseeseseeseceeseeeeseeecneeesneeeens 86 network Router RIP Context 0 ceceeeccseeecseeecseeseeeeseeescneeseeesseeeees 87 E
140. t value for T1 lines hdb3 High Density Bipolar 3 line code type Valid for E1 controller only This is the default value for E1 lines Note Use this command in configurations where the router or access server must communicate with E1 or T1 fractional data lines The T1 service provider determines which line code type ami or b8zs is required for your T1 circuit The E1 service provider determines which line code type ami or hdb3 is required for your E1 circuit Example The following example specifies B8ZS as the line code type for a T1 line X330WAN 2DS1 1 config controller 1 linecode b8zs Example X330WAN 2DS1 1 config controller 1 no linecode loopback diag Controller Context only Use the loopback diag command to put the T1 or E1 line into loopback mode Note Regarding the use of loopbacks during line setup and maintenance only one type of loopback can be defined at any given time 134 Avaya X330W 2DS1 User s Guide WAN CLI Commands Note Use this command during line set up and maintenance The syntax for this command is loopback diag loopback local Controller context Use the loopback local command to put the T1 or E1 line into loopback mode Note Regarding the use of loopbacks during line setup and maintenance only one type of loopback can be defined at any given time Note Use this command during line set up and maintenance The syntax for this command is
141. te alarm e Transmitter is sending alarm indication signal AIS e Receiver has loss of signal e Receiver is getting AIS e Receiver has loss of frame e Receiver has remote alarm e Receiver has no alarms e Receiver has major alarm Shows the current framing type The default framing type for E1 is CRC4 The default framing type for T1 is SF Displays the current line code The default line code for E1 is HDB3 The default line code for T1 is AMI Displays the current clock source The possible clock sources are either Line or Internal Displays the channel group number and timeslots Displays the current accumulation period from 1 900 seconds which rolls into a 24 hour accumulation every 15 minutes The oldest 15 minute period falls off the back of the 24 hour accumulation buffer Displays either no line code violations the occurrence of a Bipolar Violation or the occurrence of an Excessive Zeros error event Avaya X330W 2DS1 User s Guide 141 Chapter7 X330WAN CLI Commands Path Code Violations Slip Secs Fr Loss Secs Line Err Secs Degraded Mins Errored Secs Bursty Err Secs Displays one of the following e No path code violations e A frame synchronization bit error in the SF for T1 and no CRC4 for E1 frame types e ACRC4 error in the ESF for T1 and CRC4 for E1 frame types Displays if there is a replication or deletion of the payload bits of a domestic trunk interf
142. the range 1 to 65535 Example ip ospf hello interval 5 ip ospf priority Interface Mode Use the ip ospf priority command to configure interface priority used in DR election The no form of this command sets the OSPF priority to its default The default is 1 Note This command is executed from the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no ip ospf priority lt priority gt priority An integer in the range 1 to 255 Example priority 17 ip ospf router id Use the ip ospf router id command to configure router identity The no form of this command returns the router identity to its default lowest IP interface that exists Avaya X330W 2DS1 User s Guide 75 Chapter 7 X330WAN CLI Commands The syntax for this command is no ip ospf router id lt router id gt router id IP address Example X330WAN 2DS1 1 configure ip ospf router id 192 168 49 1 ip proxy arp Interface context Use the ip proxy arp command to enable proxy ARP on an interface The no form of this command disables proxy ARP on an interface Note This command is executed from the Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no ip proxy arp Example To disable proxy ARP on interface marketing X330WAN 2DS1 1 configure no ip proxy arp ip redirect Interface context Use the ip redirect command to enabl
143. tion in the table access forward deny Example X330WAN 2DS1 1 configure ip composite op access 101 17 forward ip composite op dscp Use the ip composite op dscp command to set the DSCP value of a policy operation O Note This command is only supported by the X330WAN module The syntax for this command is ip composite op dscp lt policy list number gt lt composite op index gt lt dscp value gt policy list number An integer 100 149 where 0 is the default list composite op index Index of operation in the table Avaya X330W 2DS1 User s Guide 107 Chapter 7 X330WAN CLI Commands dscp value DSCP entry an integer 0 63 where 64 no change Example X330WAN 2DS1 1 configure ip composite op dscp 101 17 52 ip composite op name Use the ip composite op name command to set the name of a policy operation Note This command is only supported by the X330WAN module The syntax for this command is ip composite op name lt policy list number gt lt composite op index gt lt OpName gt policy list number An integer 100 149 where 0 is the default list composite op index Index of operation in the table OpName The name you are givng the policy operation Example X330WAN 2DS1 1 configure ip composite op name 101 17 gold account ip composite op notify Use the ip composite op notify command to set the trap mode of a composite operation in a policy list Note This
144. tions to end the alarm LOS Definition Loss of Signal This alarm is the result of a loss of the clock synchronization signal The alarm severity is Major Indication The alarm is indicated when the SIG LED is not lit and the ALM LED is lit Corrective Actions e Check that the E1 T1 cable is properly connected to the E1 T1 ports at both ends of the connection e Check the integrity of the cable and pinouts e Ensure that the receiving and transmitting pairs are not reversed e If regenerators are used check the integrity of the regenerators LOF Red Definition Loss of Frame This alarm is the result of a loss of the frame synchronization signal The alarm severity is Major Indication The alarm is indicated when the ALM LED lights Corrective Actions Ensure that the line settings are compatable on both sides of the line For example e Ensure that both sides of the connection are configured to use the same line code and framing configuration Use the show controllers command to view the current line code Use the framing command to configure the framing mode and the line code command to configure the line code e For Tllines ensure that the line is configured for the cable length in use Use the show controllers command to view the current configuration Use the cablelength long and cablelength short commands to change the cable length configuration 34 Avaya X330W 2DS1 User s Guide Handling E1 T1 Alarms
145. ult 10 The maximum number of fragments allowed per packet Min 2 Max 2048 Default 64 In addition it is possible to restore the reassembly parameters to their default values This discards all packets currently waiting to be reassembled e Access Control and QoS per interface and direction the X330WAN supports individual Access Control and QoS lists per interface and per direction This enables the user to configure access and QoS for each direction transmit receive of each session QoS Features Efficient use of QoS enables the X330WAN to assign the proper priority to different incoming and outgoing traffic flows to minimize the affect of one flow on the other and to prevent a low priority traffic flow from affecting a high priority traffic flow and the like To achieve this the X330WAN implements multiple receiving queues and configurable transmitting queues 4 queues per interface Priority queuing is implemented among the four queues on each interface e Voice highest priority e High priority data e Better than best effort e Best effort low priority To insure minimal affect of one flow to the other the following priority order from highest to lowest is always maintained e Transmit tasks highest priority e Receive tasks medium priority e Router tasks lowest priority Note You can adjust the queue length for different needs Queue length should always be kept a small as possible while still maintaining a flo
146. umber port number for this serial port For the X330W 2DS1 this value is either 1 or 2 channel group An integer For E1 between 0 and 30 for T1 between 0 and 23 ip interface The IP interface number within this interface as a number of IP interfaces might be bound to an L3 interface An integer between 0 and 1024 Example To enter Interface Serial mode port 1 channel group 4 in ip interface 1 X330WAN 2DS1 1 configure interface Serial 1 4 1 Example X330WAN 2DS1 1 configure no interface Serial 1 4 1 keepalive Serial interface context Use the keepalive command to enable keepalive Use the no form of this command to disable keepalive The syntax for this command is no keepalive lt Seconds gt Seconds An integer 0 32767 Entering keepalive without a parameter will return the keepalive to its default of 10 seconds Entering keepalive 0 will disable keepalive linecode Controller context Use the linecode command to select the line code type for an E1 or T1 line Use Avaya X330W 2DS1 User s Guide 133 Chapter 7 X330WAN CLI Commands the no form of the command to restore the default line code type of transmission The syntax for this command is For T1 lines linecode ami b8zs For E1 lines linecode ami hdb3 ami Alternate Mark Inversion line code type Valid for both T1 and E1 controllers b8zs B8ZS line code type Valid for T1 controller only This is the defaul
147. ve access groups Use the show ip active access groups command to display all activated lists on all interfaces Note This command is only supported by the X330WAN module The syntax for this command is show ip active access groups show ip composite op Use the show ip composite op command to show a composite operation of a policy list Note This command is only supported by the X330WAN module The syntax for this command is show ip composite op lt policy list number gt lt composite operation index gt policy list number The policy list number integer from 100 to 199 Entering 0 displays the default list 118 Avaya X330W 2DS1 User s Guide Policy CLI Commands composite operation Index of the operation in the table index Example X330WAN 2DS1 1 configure show ip composite op 101 11 validate group Use the validate group command to verify that all the rules in a priority list are valid Note This command can only be executed from the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces of the X330WAN The syntax for this command is validate group lt policy list number gt lt direction gt quiet policy list number An integer 100 149 where 0 is the default list direction in out quiet Error messages not displayed Example X330WAN 2DS1 1 config if Seriall 1 validate group 101 in Avaya X330W 2DS1 User s Guide 119 Chapter 7 X3
148. vents information about routes from exiting the router interface through which the information was received This prevents routing loops Poison reverse updates explicitly indicate that a network or subnet is unreachable rather than implying they are not reachable Poison reverse updates are sent to defeat large routing loops Note This command is executed from the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is no ip rip poison reverse 78 Avaya X330W 2DS1 User s Guide Layer 3 CLI Commands ip rip rip version Interface context Use the ip rip rip version command to specify the RIP version running on the interface basis Note This command is executed from the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interfaces The syntax for this command is ip rip rip version 1 2 The possible versions of the RIP packets received and sent on an interface are 1 RIP Version 1 packets 2 RIP Version 2 packets Example To specify that RIP version 2 should be running on the basis of the interface marketing X330WAN 2DS1 1 super if Serial 1 1 ip rip rip version 2 ip rip send receive Interface context Use the ip rip send receive command to set the RIP Send and Receive mode on an interface The default state is talk listen Note This command is executed from the Serial Loopback Fast Ethernet and Fabric Fast Ethernet interf
149. w It is recommended to always use the default queue length as this is the optimal calculated length Policy In the X330WAN a policy list contains e Asset of classification rules based on a source IP destination IP source port destination port protocol and TCP Established bit The IP addresses can include wildcards Avaya X330W 2DS1 User s Guide 5 Chapter 1 Overview e A set of possible actions arranged in a Composite Operations Table e A set of DSCP mappings Several policy lists can be activated concurrently with each list applied to a different interface and direction Each Serial interface PPP session the Fast Ethernet port and the FabricFastEthernet interface can have an ingress and egress active Policy list For the FabricFastEthernet interface this list applies to all L2 interfaces VLANs mapped to this interface A default Policy list list 0 is always present and active until a different Policy list is activated The default list has one rule permit all a default DSCP mapping and a default Composite Operations table Whenever a new Policy list is created it contains a copy of the list 0 components Policy rules and the Composite Operations Table include the following actions e Access Control actions for all types of interfaces Drop Drop and Notify Forwarding e QoS actions DSCP coloring value changing for all types of interfaces Priority tag modifications for

Download Pdf Manuals

Related Search

Related Contents

OpenMCU User Manual - OpenMCU-ru  Climatizador Minisplit Instrucciones para la instalación - TN  「中国・アジア」2012．06．18−06．22記事の詳細は、情報検索  Ingersoll-Rand 650453-X Water Pump User Manual  Bedienungsanleitung Operation Manual Mode d'emploi  X-Treme XB-700Li Owners Manual  NSM-208G/NS-208G 8-Port Industrial 10/100  DーGーTーMER  2. Primeira utilização do Tablet PC  カタログpdf  

Copyright © All rights reserved. Failed to retrieve file