Home

JVC RX-8030V Receiver

1. To use the speakers connected to the FRONT SPEAKERS 7 terminals press SPEAKERS ON OFF so that the SPEAKERS 1 indicator lights up on the display Make sure that the SPEAKERS 2 indicator is not lit on the display To use the speakers connected to the FRONT SPEAKERS 2 terminals press SPEAKERS ON OFF 2 so that SPEAKERS 2 indicator lights up on the display Make sure that the SPEAKERS 1 indicator is not lit on the display To use both sets of the speakers press SPEAKERS ON OFF 1 and SPEAKERS ON OFF 2 so that the SPEAKERS 1 2 indicators light up on the display To use neither sets of the speakers press SPEAKERS ON OFF 1 and SPEAKERS ON OFF 2 so that the SPEAKERS 1 2 indicators go off from the display The HEADPHONE indicator lights up and HEADPHONE appears on the display Activating the speakers turns on the Surround and DSP modes previously selected Listening with headphones only Deactivate both sets of the front speakers and connect headphones to the PHONES jack You can enjoy the sound effects through the headphones when Surround or DSP mode is activated 3D HEADPHONE 3D H PHONE mode 3D H PHONE appears on the display and the DSP and HEADPHONE indicator lights up on the display For details see page 36 Note When you select DVD MULTI as the source o
2. B ae A component video output To S video output c To composite video output D To left right front channel audio output or to audio mixed output if necessary E F G Note When connecting a DVD player to the component video input jacks make the component video input setting correctly for AV COMPU A To component video output LINK See page 30 for details To subwoofer output C To center channel audio output D To S video output E To composite video output To left right front channel audio output G To left right surround channel audio output Note When connecting a DVD player to the component video input jacks make the component video input setting correctly for AV COMPU LINK See page 30 for details 15 Digital Connections This receiver is equipped with four DIGITAL IN terminals one digital coaxial terminal and three digital optical terminals and one DIGITAL OUT optical terminal on the rear For RX 8030VBK Another digital optical input terminal is located on the front panel see page 13 IMPORTANT When connecting a DVD player digital TV broadcast tuner or DBS tuner using the digital terminals you also need to connect it to the video jacks on the rear Without connecting it to the video jacks you can view no playback picture After connecting the comp
3. on e Om 160 320 SINGLE USE See Instruction Manual For Connection CENTER SURROUND BACK SPEAKERS wis SURROUND SPEAKERS mm SPEAKER ww FRONT SPEAKERS mur Rear Panel RX 8O30VBK 1 DIGITAL IN terminals 16 Coaxial DIGITAL 1 DVD Optical DIGITAL 2 CD DIGITAL 3 TV DIGITAL 4 CDR 2 AUDIO input output jacks 11 15 e Input IN FRONT CENTER SUBWOOFER SURR REAR TV SOUND DBS IN VCR 1 IN PLAY VCR 2 IN PLAY CD IN TAPE MD IN PLAY CDR IN PLAY PHONO IN VCR 1 OUT REC VCR 2 OUT REC TAPE MD OUT REC CDR OUT REC 3 S VIDEO and composite VIDEO input output jacks 14 15 Output e Input DVD IN TV SOUND DBS IN VCR1 IN PLAY VCR 2 IN PLAY e Output VCR 1 OUT REC VCR 2 OUT REC MONITOR OUT 4 FM AM ANTENNA terminals 8 5 PREOUT jacks 10 11 FRONT CENTER SUBWOOFER SURR SURR BACK 6 COMPONENT VIDEO input output jacks 14 15 nput DVD IN DBS IN e Output MONITOR OUT 7 COMPU LINK 4 SYNCHRO terminals 41 8 AV COMPULINK III terminals 42 9 AC power cord 16 10 DIGITAL OUT terminal 16 11 SURROUND BACK SPEAKERS terminal 10 12 SURROUND SPEAKERS terminal 10 13 CENTER SPEAKER terminal 10 14 FRONT SPEAKERS 0 terminals 10 15 FRONT SPEAKERS 2 term
4. On the unit DVDMULTI DVD cD FM AM CoCoCoCD TV DBS VCR TAPE CDR On the remote Notes For RX 8030VBK When connecting an MD recorder to the TAPE MD jack and a DBS tuner to the TV SOUND DBS jacks change the source names shown on the display For details see page 21 For RX 7030VBK RX 7032VSL When connecting an CD recorder to the TAPE CDR jacks and a DBS tuner to the TV SOUND DBS jacks change the source names shown on the display For details see page 21 17 Speaker and signal indicators on the display By checking the following indicators you can easily confirm which speakers you are activating and which signals are coming into this receiver Speaker indicators Signal indicators L Lc R L CR Ls 85 LS S RS EJ SB What speaker indicators light depends on the speaker setting for details see Setting the Speakers on page 27 The frames of L LS RS and SB light up when the corresponding speakers are set to LARGE or SMALL and when the speaker is required for the Surround DSP mode currently selected e When SUB WOOFER is set to YES SUBWFR lights up see page 27 All three frames on the row of SB are not used at the same time When SBACK OUT is set to 2SPK the left and the right ones are used When it is set to ISPK the middle one is used see page 27 T
5. 3 Push in MULTI JOG PUSH SET The current setting for the selected item appears on the display SPEAKERS 1 voume I 21 4 Turn MULTI JOG until a setting you want appears on the display ONETOUCH OPERATION SPEAKERS 1 voume I 21 5 Press EXIT 6 Repeat steps 2 to 5 to set other items if necessary 7 Press EXIT The source indication resumes on the display shows the initial setting in the following tables Setting the Speakers To obtain the best possible surround effect from the Surround and DSP modes register the setting about the speaker arrangement after all connections are completed If you have used Quick Speaker Setup on page 25 this setting is not required m Subwoofer setting SUB VV OOFEH Select whether you have connected a subwoofer or not YES Select when a subwoofer is connected NO Select when no subwoofer is used Note If you have selected NO for the subwoofer you cannot use the SUBWOOFER OUT ON OFF button on the front panel Speaker size FHONT SPEAKER CNTR SPEAKER SURR SPEAKER SBACK SPEAKER Select the size for each connected speaker LARGE Select when the speaker size is relatively large SMALL Select when the speaker size is relatively small NONE Select this when you have not connected a speaker Not selectable for the front speakers nitial setting for fr
6. Operating Other Manufacturers Video Equipment Troubleshooting rt dad Features with this mark are provided only for RX 8030VBK RX 7030V Nae Features with this mark are provided only for RX 7030VBK RX 7032VSL 32 Introduction We would like to thank you for purchasing one of our JVC products Before operating this unit read this manual carefully and thoroughly to obtain the best possible performance from your unit and retain this manual for future reference CC Compensative Compression converter ONLY for RX 8030VBK CC Converter eliminates jitter and ripples achieving a drastic reduction in digital distortion by processing the digital music data in 24 bit quantization and by expanding the sampling frequency to 128 kHz for fs 32 kHz signals 176 4 kHz for fs 44 1 kHz signals 192 kHz for fs 48 kHz signals By using the CC Converter you can obtain a natural sound field from any source See page 21 for details K2 technology ONLY for RX 8030VBK K2 technology has been designed to enable natural audio reproduction achieving a drastic reduction in digital distortion and creating original sound ambience with high precision Compatible with various audio formats including DTS 96 24 RX 8030VBK and RX 7030VBK RX 7032VSL allow you to enjoy a newly int
7. mode If Analog Direct is in use you cannot make any sound adjustments Items To do See page DIGITAL EQ Adjust equalizer pattern 32 SUBWFRLVL Adjust the subwoofer output level 32 FRONT L LVL Adjust the left front speaker output level 32 FRONTRLVL Agjust the right front speaker output level 32 CENTER LVL Adjust the center speaker output level 32 SURR L LVL Adjust the left surround speaker output level 32 SURR R LVL Adjust the right surround speaker output level 32 SBACK LVL Adjust the surround back speaker output level 32 EFFECT Adjust the DAP effect level 33 ROOMSIZE Select the room size for your virtual listening room 33 LIVENESS Select the liveness level for your virtual listening room 33 CTR TONE Make the center tone soft or sharp 33 PANORAMA Add wraparound sound effect with side wall image 33 CNTR WIDTH Adjust the center channel localization between the center speaker and the left right front speakers 33 DIMENSION Adjust sound localization position 33 CNTR GAIN Adjust sound localization of the center channel 33 Notes Adjustable when the DAP mode is in use Adjustable when Pro Logic Il Music is in use Adjustable when Neo 6 Music is in use o o c 000000 o o 000 Before you start remember There is a time limit in doi
8. w gt t u CR RX 8030VBK RX 7030VBK M G E lt a lt C gt To audio output To component video output To S video output To composite video output W gt Notes When connecting a DBS tuner to the TV SOUND DBS IN jacks change the source name to DBS which will be shown on the display when selected as the source Otherwise you cannot view any picture from DBS tuner See page 21 for details When connecting a DBS tuner to either one of the component input jacks make the component video input setting correctly for AV CONPU LINK See page 30 for details DVD player When you connect a DVD player with stereo output jacks When you connect a DVD player with its analog discrete output 5 1 channel reproduction jacks To listen to the sound after connection press DVD To listen to the sound after connection press DVD MULTI e t RX 8030VBK RX 7030VBK Sc RIGHT LEFT VIDEO S VIDEO e d i i l ex gt component video output To S video output To composite video output To left right front channel audio output or to audio mixed output if necessary w gt F G Note When connecting a DVD pl
9. 11 II VOLUME It 11 SLEEP indicator 22 MIDNIGHT MODE indicator 20 DIGITAL EQ equalization indicator 32 Speaker and signal indicators 18 Digital signal format indicators 20 Main Display 17 DSP indicator 19 38 3D PHONIC indicator 38 HEADPHONE indicator 19 38 SPEAKERS 1 2 indicators 19 INPUT ATT attenuator indicator 20 VOLUME level indicator 17 22 BASS BOOST indicator 22 Rear Panel RX 8030VBK DIGITAL DIGITAL el 3 DIGITAL 4 CDR our JPHONO 2 N N w gt o co N S VIDEO FRONT Reb a RIGHT LEFT RIGHT LEFT RIGHT LEFT SURROUND BACK SPEAKERS Cle ere us Om 160 320 X AN Pa SINGLE USE f Y f See Instruction eLan Z Y Manual For Connection RIGHT LEFT M RIGHT LEFT CENTER SPEAKER SURROUND SPEAKERS 9 FRONT SPEAKERS 2 RX 7030VBK DIGITAL IN 9 DIGITAL 1 Di DIGITAL DIGITAL FJ DIGITAL 4 10 SUBWOOFER ISURR OTIO 085 W Bed LEFT
10. Front Panel RX 8030VBK 5 RX 8030VBK o n CC CONVERTER DVD MULTI DVD TV SOUND JDBS PHONO RX 7030VBK RX 7030VBK BASS BOOST co DVD MULTI TV SOUND DBS E eee S Y a v A DIGITAL SVIDEO VIDEO L AUDIO R INPUT TUNER CONTROL VIDEO Only for RX 8030VBK Inside the front door How to open the front door Press down on PUSH OPEN Front Panel 1 O ISTANDBY ON button and STANDBY lamp 17 2 e SPEAKERS ON OFF 1 button 19 SPEAKERS ON OFF 2 button 19 3 SURROUND button 37 DSP button 39 SURROUND DSP OFF button 37 39 4 Remote sensor 5 Display window 17 6 For RX 8030VBK Source selection buttons and lamps 17 18 19 21 23 24 37 40 DVD MULTI DVD VCR 1 VCR 2 VIDEO TV SOUND DBS PHONO CD CDR TAPE MD FM AM The lamp above the button for selected source lights up For RX 7030VBK Source selection buttons 17 18 19 21 23 24 37 40 DVD MULTI DVD VCR TV SOUND DBS CD TAPE CDR FM AM 7 MASTER VOLUME control 18 8 For RX 8030VBK CC CONVERTER button and lamp 21 For RX 7030VBK BASS BOOST button and lamp 22 9 SUBWOOFER
11. is selected for the speaker settings 1 Press SOUND e Speaker output levels except the subwoofer output level are not adjustable when Analog Direct is in use To adjust The 10 keys are activated for sound adjustments subwoofer output level see page 19 2 Press DIGITAL EQ Equalization repeatedly to select the center frequency you want to adjust Each time you press the button the center frequency with its current level appear on the display 3 Press LEVEL or repeatedly to adjust the level of the center frequency The DIGITAL EQ indicator lights up on the display The frequency level changes from 8 dB to 8 dB in 2 dB steps 4 Repeat steps 2 and 3 to adjust the other center frequency 32 You can also use the remote control for adjusting the speaker output level When using the remote control you can make an adjustment while listening to test tone de PAZ 6S 0 o ap a e S7 0 1 Press SOUND The 10 keys are activated for sound adjustments 2 Press TEST to check if you can hear the sounds through all the speakers at equal level Test tone comes out of the speakers in the following order No test tone comes out of the deactivated speakers and the subwoofer FRNT L Left front speaker gt CENTER Center speaker gt FRNT R Right front speaker gt SURR R Right surround speaker S BACK surround back speaker SURR L Left su
12. CD IN CDR IN TAPE MD IN 200 mV 47 Audio Input DIGITAL IN Coaxial DIGITAL 1 DVD 0 5 75 Q Optical DIGITAL 2 CD DIGITAL 3 TV DIGITAL 4 CDR 2 dBm to 15 dBm 660 nm 30 nm Corresponding to Linear PCM Dolby Digital and DTS Digital Surround with sampling frequency 32 kHz 44 1 kHz 48 kHz Audio Output Level PRE OUT 1V Recording Output Level VCR 1 OUT VCR 2 OUT CDR OUT TAPE MD OUT 200 mV Optical DIGITAL OUTPUT Signal wave length 660 nm Output level 21 dBm to 15 dBm Signal to Noise Ratio 66 IHF 78 THF Digital output PHONO IN 70 dB 78 dB at REC OUT DVD IN VCR 1 IN VCR 2 IN TV SOUND DBS IN VIDEO 87 dB 80 dB CD IN CDR IN TAPE MD IN 87 dB 80 dB Frequency Response 8 Q PHONO IN 20 Hz to 20 kHz 1 dB DVD IN VCR 1 IN VCR 2 IN TV SOUND DBS IN VIDEO 20 Hz to 100 kHz 1 dB 3 dB CD IN CDR IN TAPE MD IN 20 Hz to 100 kHz 1 dB 3 dB RIAA Phono Equalization 1 0 dB 20 Hz to 20 kHz Equalization 5 bands 63 Hz 250 Hz 1 kHz 4 kHz 16 kHz 8 dB Bass boost 6 dB 1 0 dB at 100 Hz Video Video Input Sensitivity Impedance Composite video DVD IN VCR 1 IN VCR2 IN TV SOUND DBS IN VIDEO 1 V p p 75 S video DVD IN VCR 1 IN VCR 2 IN TV SOUND DBS IN VIDEO Y luminance 1 V p p 75 chrominance burst 0 286 V p p 75 Q Component video DVD IN DBS IN Y luminance 1 V p p 75 Q 0 7 V p p 75
13. Keep the following comments in mind as reference when adjusting If the size of the cone speaker unit built in your speaker is larger than 12 cm 4 5 4 inches select LARGE and if it is smaller than 12 cm 4 inches select SMALL e f you have selected NO for the subwoofer setting can only select LARGE for the front speakers e f you have selected SMALL for the front speakers you cannot select LARGE for the center surround and surround back speakers e If you have selected SMALL for the surround speakers you cannot select LARGE for the surround back speakers f you have selected NONE for the surround speakers the surround back speakers are fixed to NONE m Surround back speakers quantity SBACK OUT Select the number of the surround back speakers connected 1SPK Select this to use 1 surround back speaker 2SPK Select this to use 2 surround back speakers Note If you have selected NONE for the surround back speakers see above this setting is not available 27 Setting the Speaker Distance The distance from your listening point to the speakers is another important element to obtain the best possible sound of the Surround and DSP modes Set the distance from your listening point to the speakers By referring to the speaker distance setting this unit automatically sets the delay time of the sound through each speaker so that sounds thro
14. gt For RX 7030VBK RX 7032VSL pee To audio input RX 8030VBK COE ex cm idi To audio output RX 7030VBK RX 7032VSL To S video output To composite video output To S video input To composite video input c DOTO C DBS tuner To audio output To component video output To S video output To composite video output W Notes e When connecting a DBS tuner to the TV SOUND DBS IN jacks change the source name to DBS which will be shown on the display when selected as the source Otherwise you cannot view any picture from DBS tuner See page 21 for details e When connecting a DBS tuner to either one of the component input jacks make the component video input setting correctly for AV COMPU LINK See page 30 for details 14 DVD player When you connect a DVD player with stereo output jacks When you connect a DVD player with its analog discrete output 5 1 channel reproduction jacks To listen to the sound after connection press DVD To listen to the sound after connection press DVD MULTI RX 8030VBK v ec jue i RX 8030VBK HOLO RX 7030VBK RX 7032VSL i RX 7030VBK RX 7032VSL S VIDEO So 6 gt amp
15. 2 DVD 3 CD 4 TV or DBS With the ONE TOUCH OPERATION indicator lit the volume If you have changed the source name from TV to DBS level for the currently selected source is recalled when the DBS appears see page 21 source is selected To cancel the One Touch Operation Setting the Component Video Input Set One Touch Operation to OFF so that the ONE TOUCH When you use the component video inputs for connecting the DVD OPERATION indicator goes off player and or DBS tuner register the type of input jacks If you have not selected appropriate video input jacks the AV COMPU LINK remote control system cannot operate properly See page 42 m Forthe DVD player VIDEO IN DVD Select one of the following COMPNT Select when connecting the DVD player to the component video input jacks S C Select when connecting the DVD player to the composite video or S video input jacks m Forthe DBS tuner VIDEO IN DBS Select one of the following COMPNT Select when connecting the DBS tuner to the component video input jacks S C Select when connecting the DBS tuner to the composite video or S video input jacks 30 Adjusting Sound You can make sound adjustment to your preference after completing basic setting Basic Setting Items On the following pages you can adjust the items listed below You can adjust only the items applicable to the current sound
16. 42 1 If you have already plugged your VCR DVD player TV and this receiver into the AC outlets unplug their AC power cords first 2 Connect your VCR DVD player TV and this receiver using the cables with the monaural mini plugs not supplied See CONNECTIONS 1 on the previous page 3 Connect the audio input output jacks on VCR DVD player TV and this receiver using the cables with RCA pin plugs See pages 14 and 15 4 Connect the video input output jacks on VCR DVD player TV and this receiver using the cables with RCA pin plugs S video plug or component video plugs See CONNECTIONS 2 on the previous page 5 Plug the AC power cords of the components and the receiver into the AC outlets 6 When turning on the TV for the first time after the AV COMPU LINK connection turn the TV volume to the minimum using the TV volume control on the TV 7 Turn on the connected components first then turn on this receiver When turning on the VCR use the remote control supplied with this receiver The AV COMPU LINK remote control system allows you to use the five basic functions listed below Remote Control of the TV DVD player and VCR Using This Remote Control See page 46 for details Aim the remote control directly at the remote sensor on each target component One Touch Video Play Simply by inserting a video cassette without its safety tab into the VCR you can enjoy the video playba
17. Surround Modes Applicable to the Various Software Available Surround modes vary depending on the speaker settings and the incoming signals The table below shows the relation of the Surround modes and the incoming signals with the surround back speakers and EX ES setting The numbers inside the parentheses following the incoming signal type indicate the number of the front channels and that of the surround channels For example 3 2 indicates that the signals are encoded with three front signals left right center and two stereo surround signals Incoming Signal Type Surround Back Channel Setting EX ES Setting Available Surround Mode Dolby Digital EX 2SPK 1SPK AUTO ON DOLBY D EX OFF DOLBY D NONE AUTO ON DOLBY D VIRTUAL SB OFF DOLBY D Dolby Digital 3 2 2 2 2SPK 1SPK AUTO DOLBY D ON DOLBY D EX OFF DOLBY D NONE Not available DOLBY D Dolby Digital 3 1 2 1 2SPK 1SPK AUTO ON OFF DOLBY D NONE Not available DOLBY D Dolby Digital 1 0 3 0 2SPK 1SPK NONE Not available DOLBY D Dolby Digital Dual Mono 2SPK 1SPK NONE Not available DUAL MONO DTS ES Discrete 6 1ch 2SPK 1SPK AUTO ON ES DSCRETE OFF DTS NONE AUTO ON DTS VIRTUAL SB DTS ES Matrix 6 1ch 2SPK 1SPK AUTO ON ES MATRIX DTS ES 96 24 Matrix OFF DTS NONE AUTO ON DTS VIRTUAL SB OFF DTS DTS DTS 96 24 3 2 2 2 2SPK 1SPK AUTO DTS 2 DTS 96 24 processing is not ON DTS NEO 6 2 _
18. back to the beginning When connecting an MD recorder to the digital input terminal change the source name to MD from TAPE see page 21 f you have changed the source name from TV to DBS DBS appears see page 21 29 For RX 7030VBK Memorizing the Volume Level for Each Source As you set the components connected to the digital coaxial This unit memorizes some settings separately for each source terminal DIGITAL IN 1 the optical terminals DIGITAL IN 2 In addition you can store the volume level for each source with the 4 will be automatically fixed to connect the components listed other memorized settings One Touch Operation below m One Touch Operation ONE TOUCH OPE When DIGITAL IN 1 DGTL IN COAX is set to DVD Select one of the following 2 C D 3 TV or DBS 4 CDR ON Select to store the volume level separately for each When DIGITAL IN 1 DGTL IN COAX is set to CD source The ONE TOUCH OPERATION indicator lights 2 DVD 3 TV or DBS 4 CDR up on the display This receiver memorizes the volume level When DIGITAL IN 1 DGTL IN COAX is set to TV or pps when you change the source or when you change the source name Z DND 3 CD CDR OFF Select this not to store the volume level 333 When DIGITAL IN 1 DGTL IN COAX is set to CDR To recati the level
19. os ES setting to NONE Not available DTS DTS 3 1 2 1 2SPK 1SPK AUTO ON OFF DTS NONE Not available DTS DTS 1 0 3 0 2SPK 1SPK NONE Not available DTS DTS Dual Mono 2SPK 1SPK NONE Not available DUAL MONO Incoming Signal Type Available Surround Mode Analog PCM Dolby Digital 2 0 DTS 2 0 PL II MOVIE PL II MUSIC PRO LOGIC NEO 6 CINMA NEO 6 MUSIC DVD MULTI None HEADPHONE Mode 3sD PHONE You can also enjoy the Surround modes through the headphones If you press SURROUND when the front speakers 1 and 2 are both deactivated 3D HEADPHONE mode 3D H PHONE is activated without respect to the type of software played back 3D H PHONE appears on the display and the DSP and HEADPHONE indicators also light up Virtual 6 1 channel surround If you have connected and activated the surround speakers you can use Virtual 6 1 channel surround when playing back Dolby Digital EX or DTS ES software without connecting the surround back speakers This surround reallocates the surround back channel to the surround speakers so that you can still feel the great surround effect from behind The VIRTUAL SB Surround Back indicator lights up on the display 36 Activating the Surround Modes Activating the Surround Modes Available Surround modes vary depending on the speaker settings and the incoming signals See page 36 Activating one of the Surround modes for a source automatically r
20. CD Gere 13 SURROUND DSP SURR DSP ANALOG 4 2 Cor Ll BASSBOOST k FRONT L eKFRONT R 2 20203 5 s Ge 4 5 6 MIDNIGHT SURAT TERR 1 15 6 mP 8 9 com EDIGITALEQ SURR BACK 7 808 Go 0 Go RETURN FMMODE 100 GNI A FACCUACC 16 ae AIA A pero CH LEVEL TV VOL VOLUME 17 Ba we SWS Ee n IE CONTROL CONI MUTING Eag ell GN Wa 19 REC PAUSE btn SLEEP DOWN TUNING UP fiz e IS oc DIMMER AN CONTROL RECEIVER CATV DBS CONTROL button 47 TV VIDEO button 46 47 For RX 8030VBK CONTROL button 44 46 For RX 7030VBK VCR CONTROL button 46 REC PAUSE button 45 46 48 SLEEP button 22 ANALOG DIGITAL INPUT button 20 ANALOG DIRECT button 21 10 keys for operating the tuner 24 10 keys for adjusting sound 32 33 10 keys for operating audio video components 44 48 CH channel buttons 46 48 LEVEL buttons 32 33 44 The LEVEL buttons function only after pressing SOUND then 10 keys which are marked with an asterisk on the remote control VOLUME buttons 18 TV VOL volume buttons 46 47 MUTING button 22 TUNING UP DOWN buttons 23 Operating buttons for audio video components 44 46 48 gt Il Bl 4 REW FF gt 1 DIMMER button 22 Only for RX 7030VBK TAPE CDR CONTROL button 45
21. Remote Control 1 Batteries 2 AM Loop Antenna 1 FM Antenna 1 If anything is missing contact your dealer immediately Putting Batteries in the Remote Control Before using the remote control insert the two supplied batteries first 1 2 3 R6P SUM 3 lt 15 c a Gee e ex 1 Press and slide the battery cover on the back of the remote control 2 Insert the batteries e Make sure to match the polarity to and to gt 3 Replace the cover If the remote control cannot transmit signals or operate the receiver correctly replace the batteries Use two R6P SUM 3 AA 15F type dry cell batteries Notes Supplied batteries are for the initial setup Replace for continued use e After replacing the batteries set the manufacturers codes again see pages from 47 to 49 CAUTION Follow these precautions to avoid leaking or cracking cells Place batteries in the remote control so they match the polarity to and to Use the correct type of batteries Batteries that look similar may differ in voltage Always replace both batteries at the same time Do not expose batteries to heat or flame Connecting the FM and AM Antennas FM Antenna Connections FM Antenna supplied AM EXT Extend the supplied FM antenna horizontally
22. FM AM Gea eyes TV DBS VCR TAPE CI E SURROUND DSP SURR DSP orect 9 14 4 EXES BASSBOOST FRONT L FRONT R c e C 3 CENTERS BWOORRR 5 ne C5 08 MIDNIGHT ee xSURR R 15 6 ewvc mP 8 9 kDIGITALEQ kSURR BACK e 100 0 10 RETURN FMMODE 100 16 Li m B ei Aie 2 i Erat simis 20 SLEEP DOWN TUNING UP oe DIMMER AN CONTROL RECEIVER SOUND button 22 32 33 CATV DBS CONTROL button 47 TV VIDEO button 46 47 For RX 8030VBK CONTROL button 44 46 For RX 7030VBK RX 7032VSL VCR CONTROL button 46 REC PAUSE button 45 46 48 SLEEP button 22 ANALOG DIGITAL INPUT button 20 ANALOG DIRECT button 21 10 keys for operating the tuner 24 10 keys for adjusting sound 32 33 10 keys for operating audio video components 44 48 CH channel buttons 46 48 LEVEL buttons 32 33 44 The LEVEL buttons function only after pressing SOUND then 10 keys which are marked with an asterisk on the remote control VOLUME buttons 18 TV VOL volume buttons 46 47 MUTING button 22 TUNING UP DOWN buttons 23 Operating buttons for audio video components 44 46 48 gt Il I4 4 REW FF P
23. If Analog Direct is in use you cannot make any sound adjustments ltems To do See page DIGITAL EQ Adjust equalizer pattern 32 SUBWFR LVL Adjust the subwoofer output level 32 FRONT L LVL Adjust the left front speaker output level 32 FRONTRLVL Agjust the right front speaker output level 32 CENTER LVL Adjust the center speaker output level 32 SURRL LVL Adjust the left surround speaker output level 32 SURR R LVL Adjust the right surround speaker output level 32 SBACK LVL Adjust the surround back speaker output level 32 EFFECT Adjust the DAP effect level 33 ROOMSIZE Select the room size for your virtual listening room 33 LIVENESS Select the liveness level for your virtual listening room 33 CTR TONE Make the center tone soft or sharp 33 PANORAMA Add wraparound sound effect with side wall image 33 CNTR WIDTH Adjust the center channel localization between the center speaker and the left right front speakers 33 DIMENSION Adjust sound localization position 33 CNTR GAIN Adjust sound localization of the center channel 33 Notes Adjustable when the DAP mode is in use Adjustable when Pro Logic Il Music is in use 8 Adjustable when Neo 6 Music is in use 000 J amp O 0 o o c oa 000000 o o oS hl Before you start remembe
24. The last received station of the selected band is tuned in AUTOMUTING Normally select this Each time you press the button the band alternates between When a program is broadcasted in stereo FM and AM you will hear stereo sound when in monaural you will hear monaural 2 Press the 10 keys to select a preset channel sounds number This mode is also useful to suppress static noise between stations The AUTO MUTING indicator lights up on the display Initial setting For channel number 5 press 5 For channel number 15 press 10 then 5 For channel number 20 press 10 then 10 For channel number 30 press 10 10 then 10 MODE MONO Select this to improve the reception but stereo effect will be lost In this mode you will hear noise while Note tuning into the stations The AUTO ie Gen sage MUTING indicator goes off from the display The STEREO indicator also goes off When you use the 10 keys on the remote control be sure that they are activated for the tuner not for the CD and others See page 44 Note When you use the FM MODE on the remote control be sure that it is activated for the tuner not for the CD and others See page 44 24 EE Basic Settings Some of the following settings are required after connecting and positioning your speakers while others will make operations easier You can use QUICK SPEAKER SETUP to easily set up your speaker configuration Setting the Speakers Confi
25. Video Output Level Composite video VCR 1 OUT VCR 2 OUT MONITOR OUT 1 V p p 75 Q S video VCR 1 OUT VCR 2 OUT MONITOR OUT Y luminance 1 V p p 75 chrominance burst 0 286 V p p 75 Q Component video MONITOR OUT Y luminance 1 V p p 75 0 7 V p p 75 Q Synchronization Negative Signal to Noise Ratio 45 dB FM tuner IHF Tuning Range 87 5 MHz to 108 0 MHz Usable Sensitivity Monaural 12 8 dBf 1 2 uV 75 16 0 dBf 1 7 75 37 5 dBf 20 5 uV 75 Q 35 dB at 1 kHz 50 dB Quieting Sensitivity Monaural Stereo Stereo Separation at REC OUT AM tuner Tuning Range 530 kHz to 1 710 kHz General AC 120V 60 Hz 320 W 440 VA at operation 2 W in standby mode 435 mm x 157 mm x 425 mm 17 3 16 in x 6 3 16 in x 16 3 4 in 12 2 kg 27 0 lbs Power Requirements Power Consumption Dimensions W x H x D Mass Designs amp specifications are subject to change without notice 51 RX 7030VBK Amplifier Output Power At Stereo operation Front ch 110 W per channel min RMS driven into 8 O 20 Hz to 20 kHz with no more than 0 08 total harmonic distortion At Surround operation Front ch 110 W per channel min RMS driven into 8 Q at 1 kHz with no more than 0 896 total harmonic distortion Center ch 110 W min RMS driven into 8 Q at 1 kHz with no more than 0 8 total harmonic distortion Surround ch 110 W per channel min RMS dri
26. When using the digital input terminal Select the digital input mode correctly For details see Selecting the Analog or Digital Input Mode on page 19 13 VCR s TV and or DBS tuner To listen to the sound after connection press VCR 1 or VCR 2 for To listen to the sound after connection press TV SOUND DBS or RX 8030VBK or VCR for RX 7030VBK RX 7032VSL TV DBS on the remote control For RX 8030VBK You can connect two VCRs one to the VCR 1 jacks and the other to the VCR 2 jacks pic Gre 20 E gt j CE If your VCR has an AV COMPU LINK jack connect it to the RX 8030VBK VCR 1 jack so that you can use the AV COMPU LINK remote RX 7030VBK RX 7032VSL eje vg 3 OORO control system Aj To audio input A atm To audio output c To S video output um 7 D To composite video output ing fe 1O a RX 8030VBK E To S video input IE 1 W Ote AUDIO jacks TV F To composite video input SOUND DBS IN E DO NOT connect Pos the TV s video output to these video input jacks EI Connect the TV to appropiate MONITOR OUT jacks to view the playback picture from any other connected video components To audio output To component video input To S video input To composite video input
27. Adjustable range 0 to 0 5 35 Using the Surround Modes This unit activates a variety of Surround modes automatically The basic settings and adjustments stored see pages 25 to 33 are applied Reproducing Theater Ambience Introducing the Surround Modes In a movie theater many speakers are located on the walls to reproduce impressive multi surround sounds reaching you from all directions With these many speakers sound localization and sound movement can be expressed Surround modes built in this receiver can create almost the same surround sounds as you can feel in a real movie theater with only five to seven speakers plus subwoofer 2 0 ow B DU BDBDBgBg D Gg ununun ID ID ILI IL unnu HHHH HHH HEHEHHE ID ID ID ID ID D ID mnununuuu un Subwoofer Left front speaker Center speaker Right front speaker L C R LN Ce _ Left surround Surround back speakers LSB RSB M Right surround speaker LS speaker RS 34 Dolby Digital Dolby Digital is a digital signal compression method developed by Dolby Laboratories and enables multi channel encoding and decodi
28. From the remote control 1 Press FM AM Each time you press the button the band alternates between FM and AM 2 Press TUNING UP or TUNING DOWN repeatedly until you find the frequency you want Pressing TUNING UP increases the frequency Pressing TUNING DOWN decreases the frequency JVC EE SE MZ sz tJ 205 Te Once a station is assigned to a channel number the station be quickly tuned in You can preset up to 30 FM and 15 AM stations To store the preset stations Before you start remember There is a time limit in doing the following steps If the setting is canceled before you finish start from step 2 again On the front panel ONLY 1 Tune in the station you want to preset see Tuning in to Stations Manually on the left If you want to store the FM reception mode for this station select the FM reception mode you want See Selecting the FM Reception Mode on page 24 2 Press MEMORY SPEAKERS 1 voume IZ The channel number position starts flashing on the display for about 10 seconds 3 Press FM AM PRESET A or V to select a channel number while the channel number position is flashing SPEAKERS 1 voume 4 Press MEMORY again while the selected channel number is flashing on the display The selected channel number sto
29. JVC REMOTE CONTROL RM SRX8030J mar Only for RX 8030VBK Display window When the remote operation mode changes it is shown on this display e Signal transmission indicator lights up when transmitting signals 0 1 buttons 17 46 48 For RX 8030VBK CATV DBS dl VCR 1 cl TV 0 1 AUDIO Ql For RX 7030VBK CATV DBS 0 1 VCR 0 1 TV 0 1 AUDIO 0 1 Source selection buttons 17 18 19 23 24 37 40 For RX 8030VBK DVD MULTI DVD CD FM AM VCR 1 VCR 2 CDR TAPE MD TV DBS VIDEO PHONO For RX 7030VBK DVD MULTI DVD CD FM AM TV DBS VCR TAPE CDR When you press one on these source selection buttons on the remote control the receiver automatically turns on SURROUND button 37 DSP button 39 SURR surround DSP OFF button 37 39 EX ES button 37 For RX 8030VBK CC CONVERTER button 21 For RX 7030VBK CD DISC button 45 MIDNIGHT MODE button 20 SOUND button 22 32 33 RX 70O30VBK CQ gt N 21 JVC REMOTE CONTROL RM SRX7030J mire Bony con 3 QD DVD MULTI DVD FM AM 3 TV DBS VCR TAPE CDR ANALOGIDIGITAL
30. Reproduces the spatial feeling of a large theater where the seating capacity is about 600 THEATER 2 Reproduces the spatial feeling of a small theater where the seating capacity is about 300 The built in Dolby Pro Logic Il decoder is activated when playing back 2 channel analog or digital source The DO PRO LOGIC II indicator lights up When using the DAP mode the sounds come out of all the connected and activated speakers If surround speakers are set to NONE in the speaker setting JVC s original 3D PHONIC processing which has been developed to create the surround effect through the front speakers only is used The 3D PHONIC indicator lights up on the display ALL Channel Stereo mode This mode can reproduce a larger stereo sound field using all the connected and activated speakers This mode cannot be used without activating the surround speakers If the front speakers are deactivated All Channel Stereo cannot be selected Sound reproduced from All Channel Stereo mode Monaural Film In order to reproduce a more acoustic sound field in your listening room while viewing monaural sound video software analog and 2 channel digital signals you can use this mode The surround effect will be added and the sound localization of actor s words will be improved This mode cannot be used for multi channel digital signals When MONO FILM is used sounds come out of all the connected
31. Return to the beginning of the current or previous chapter Skip to the beginning of the next chapter Stop playing gt gt Pause playing To resume press After pressing DVD or DVD MULTI these buttons can be used for the DVD menu operations 22 9 C QC Cv Note For detailed menu operations refer to the instructions supplied with the discs or the DVD player TV You can always perform the following operations TV OMI Turn on or off the TV TV VOL Adjust the volume TV VIDEO Set the input mode either TV or VIDEO After pressing TV DBS you can perform the following operations Change the channels 1 9 0 100 Select the channels RETURN Alternate between the previously selected channel and the current channel Operating Other Manufacturers Video Equipment This remote control supplied with the receiver can transmit control signals for other manufacturers TVs CATV converters DBS tuners VCRs and DVD players When operating the other manufacturers components refer also to the manuals supplied with them After replacing batteries for the remote control you need to set the manufactures codes again To change the transmittable signals for operating another manufacturer s TV 1 Press and hold TV ci 2 Press TV DBS For RX 8030VBK CALL appears on the display window of the remote control 3 Enter a ma
32. You can also enjoy the DSP effect except All Channel Stereo mode through the headphones If you press DSP when the front speakers 1 and 2 are both deactivated 3D HEADPHONE mode is activated without respect to the type of software played back 3D H PHONF appears on the display and the DSP and HEADPHONE indicators also light up 38 To use the DSP modes press DSP so that the DSP modes change as follows The DSP indicator also lights up on the display gt HALL 1 gt HALL 2 gt LIVE CLUB gt DANCE CLUB PAVILION ALL STEREO THEATER 1 gt THEATER 2 MONO FILM Back to the beginning Suitable for audio sources Suitable for video sources DAP modes You can use the following DAP modes in order to reproduce a more acoustic sound field in your listening room HALL 1 Reproduces the spatial feeling of a large shoebox shaped hall designed primarily for classical concerts Its seating capacity is about 2000 Reproduces the spatial feeling of a large vineyard shaped hall designed primarily for classical concerts Its seating capacity is about 2000 Reproduces the spatial feeling of a live music club with a low ceiling HALL 2 LIVE CLUB DANCE CLUB Reproduces the spatial feeling of a rocking dance club PAVILION Reproduces the spatial feeling of an exhibition hall with a high ceiling THEATER 1
33. Analog Direct see page 21 Digital Equalization see page 32 Speaker channel output levels see page 32 Surround and DSP mode selection see pages 37 and 39 Bass Boost setting see the left column Notes e f the source is FM or AM you can assign a different setting for each band e f you want to memorize the volume level with the above settings set One Touch Operation to ON see page 30 a Receiving Radio Broadcasts You can browse through all the stations or use the preset function to go immediately to a particular station Tuning in to Stations Manually Using Preset Tuning JVC eo zb CEL ESVZ c e Sd sos Top 9 1 Press FM or AM to select the band The last received station of the selected band is tuned in TUNED STEREO SPEAKERS 1 voume IZ 21 2 Press FM AM TUNING repeatedly until you find the frequency you want Pressing FM AM TUNING A increases the frequency Pressing FM AM TUNING decreases the frequency SPEAKERS 1 voume IZ I Notes e When a station of sufficient signal strength is tuned in the TUNED indicator lights up on the display When an FM stereo program is received the STEREO indicator also lights up When you hold and then release the button in step 2 the frequency keeps changing until a station is tuned in
34. DIGITAL 1 DVD el RIGHT LEFT DIGITAL 2 CD DIGITAL CAUTION SPEAKER IMPEDANCE on 80 160 e Om 160 320 DIGITAL 4 CENTER SURROUND BACK SPEAKERS wis SURROUND SPEAKERS ww FRONT SPEAKERS mur 10 11 12 13 14 15 Rear Panel RX 8030VBK 1 Differences between RX 8030VBK and RX 7030VBK RX 7032VSL DIGITAL IN terminals 16 e Coaxial DIGITAL 1 DVD Optical DIGITAL 2 CD DIGITAL 3 TV DIGITAL 4 CDR AUDIO input output jacks 11 15 e Input IN FRONT CENTER SUBWOOFER SURR REAR TV SOUND DBS IN VCR 1 IN PLAY VCR 2 IN PLAY CD IN TAPE MD IN PLAY CDR IN PLAY PHONO IN VCR 1 OUT REC VCR 2 OUT REC TAPE MD OUT REC CDR OUT REC S VIDEO and composite VIDEO input output jacks 14 15 Output e Input DVD IN TV SOUND DBS IN IN PLAY VCR 2 IN PLAY Output VCR 1 OUT REC VCR 2 OUT REC MONITOR OUT FM AM ANTENNA terminals 8 PREOUT jacks 10 11 FRONT CENTER SUBWOOFER SURR SURR BACK COMPONENT VIDEO input output jacks 14 15 Input DVD IN DBS IN e Output MONITOR OUT COMPU LINK 4 SYNCHRO terminals 41 AV COMPULINK III terminals
35. Dolby Digital 5 1CH DOLBY D encoding method records and digitally compresses the left front channel right front channel center channel left surround channel right surround channel and LFE channel signals total 6 channels but the LFE channel is counted as 0 1 channel Therefore called 5 1 channel Dolby Digital enables stereo surround sounds and sets the cutoff frequency of the surround treble at 20 kHz compared to 7 kHz for Dolby Pro Logic As such the sound movement and being there feeling are enhanced much more than Dolby Pro Logic Dolhy Digital EK Dolby Digital EX DOLBY D EX is a digital surround encoding format that adds the third surround channels called surround back Compared to the conventional Dolby Digital 5 1CH these newly added surround back channels can reproduce more detailed movements behind you while viewing the video software In addition surround sound localization will become more stable You can use Virtual 6 1 channel surround when playing back Dolby Digital EX software without connecting the surround back speakers This surround reallocates the surround back channel to the surround speakers so that you can still feel the great surround effect from behind The VIRTUAL SB Surround Back indicator lights up on the display Dolby Pro Logic Dolby Surround encoding format records the left front channel right front channel center channel and surround channel monaural signals into
36. FM AM RX 7030VBK Composite video 3 2 DVD MULTI DVD VCR S video 3 2 x x TV SOUND DBS CD TAPE CDR FM AM Component video 2 1 Remote Control Display Window RM SRX8030J RM SRX7030J x ES Getting Started This section explains how to connect audio video components and speakers to the receiver and how to connect the power supply Before Installation General Precautions Be sure your hands are dry Turn the power off to all components Read the manuals supplied with the components you are going to connect Locations nstall the receiver in a location that is level and protected from moisture The temperature around the receiver must be between 5 C and 35 C 23 F and 95 F Make sure there is good ventilation around the receiver Poor ventilation could cause overheating and damage the receiver Handling the receiver Do not insert any metal object into the receiver Do not disassemble the receiver or remove screws covers or cabinet Do not expose the receiver to rain or moisture Checking the Supplied Accessories Check to be sure you have all of the following items which are supplied with the receiver The number in the parentheses indicates quantity of the pieces supplied Remote Control 1 Batteries 2 AM Loop Antenna 1 FM Antenna 1 If anything is missing contact your dealer immediately Putting Batteries in t
37. Selecting the Front Speakers oett rees 19 Activating and Adjusting the Subwoofer Sound 19 Selecting the Analog or Digital Input Mode 19 Setting the Dynamic Range 20 Attenuating the Input Signal 20 Turning Analog Direct On and Off sss 21 Making Sounds Natural eere interiit tton 21 Changing the Source Name eee 21 Reinforcing the Bass Ml titig the Sound ertt rrt Changing the Display Brightness sess 22 Usine the Sleep Timer niente ttn iteen 22 Receiving Radio Broadcasts 23 Tuning in to Stations Manually sss 23 Using Preset TUDING 23 Selecting the FM Reception Mode sss 24 This mark indicates that ONLY the remote control CAN be used for the operation explained This mark indicates that the remote control CANNOT be used for the operation explained Use the buttons on the front panel Setting the Speakers Configuration ssssss Basic Setting Items teer tet exits Basic ProCed ie e re tr eer rie oO Setting the Speakers Setting the Speaker Distance Setting the Bass Sounds ce crt tients Selecting main or sub chann
38. components refer also to the manuals supplied with them After replacing batteries for the remote control you need to set the manufactures codes again To change the transmittable signals for operating another manufacturer s TV 1 Press and hold TV 2 Press TV DBS For RX 8030VBK CALL appears on the display window of the remote control 3 Enter a manufacturer s code using buttons 1 9 and 0 See the list on page 49 to find the code 4 Release TV ci The following buttons can be used for operating a TV TV Ol Turn on and off a TV TV VOL Adjust the volume TV VIDEO Set the input mode either TV or VIDEO After pressing TV DBS you can perform the following operations on a TV CH Change the channels 1 10 0 0 100 10 Select the channels The 10 0 button will function as the ENTER button if your TV requires pressing ENTER after selecting a channel number Notes All the functions listed above may not be assigned to the buttons for some TVs e f you cannot change the channels of some TVs by pressing 10 keys press CH for changing the channels 5 Try to operate your TV by pressing TV cl When your TV turns on or off you have entered the correct code If there are more than one code listed for your brand of TV try each one until the correct one is entered To change the transmittable signals for operating a CATV converter or DBS tuner 1 Press and ho
39. oss pco CH LEVEI TV VOL VOLUME T 9 3 e s V z Oe MUTNG E 9 AN 6 1 necrause EW FF gt gt mE gt D ra DOWN TUNING P 12_ oa DIMMER JVC Only for 8030 Display window When the remote operation mode changes it is shown on this display Signal transmission indicator lights up when transmitting signals 9 1 buttons 17 46 48 For RX 8030VBK CATV DBS VCR 1 TV AUDIO Ql For RX 7030VBK RX 7032VSL CATV DBS 0 1 VCR TV 011 AUDIO 0 1 Source selection buttons 17 18 19 23 24 37 40 For RX 8030VBK DVD MULTI DVD CD FM AM VCR 1 VCR 2 CDR TAPE MD TV DBS VIDEO PHONO For RX 7030VBK RX 7032VSL DVD MULTI DVD CD FM AM TV DBS VCR TAPE CDR When you press one on these source selection buttons on the remote control the receiver automatically turns on SURROUND button 37 DSP button 39 SURR surround DSP OFF button 37 39 EX ES button 37 For RX 8030VBK CC CONVERTER button 21 For RX 7030VBK RX 7032VSL CD DISC button 45 MIDNIGHT MODE button 20 RBX 7030VBK BRX 7032VSL JVC mi3re 21 17 Con Con Con DVD MULTI DVD
40. the connected components will turn off standby Synchronized Recording Synchronized recording means the cassette deck or MD recorder starts recording as soon as a CD begins playing To use synchronized recording follow these steps 1 Put a tape in the cassette deck or an MD in the MD recorder and a disc in the CD player 2 Press the record button and the pause 1 button on the cassette deck or MD recorder at the same time This puts the cassette deck or MD recorder into recording pause If you do not press the record 6 button and pause II button at the same time the synchronized recording feature will not operate 3 Press the play gt button on the CD player The source changes on the receiver and as soon as play starts the cassette deck or MD recorder starts recording When the play ends the cassette deck or MD recorder enters recording pause and stops about 4 seconds later Notes e During synchronized recording the selected source cannot be changed e f the power of any component is shut off during synchronized recording the COMPU LINK remote control system may not operate properly In this case you must start again from the beginning 41 B AV COMPU LINK Remote Control System The AV COMPU LINK remote control system allows you to operate JVC s video components TV VCR and DVD player through the receiver This receiver is equipped with the AV COMPU LINK III w
41. 2 channels The Dolby Pro Logic PRO LOGIC decoder built in this receiver decodes these 2 channel signals into 4 original channel signals plus subwoofer matrix based multi channel reproduction e When Dolby Pro Logic is activated the DO PRO LOGIC indicator lights up on the display Dolby Pro Logic II Dolby Pro Logic II is a multi channel playback format to convert 2 channel software into 5 channel plus subwoofer The matrix based conversion method used for Dolby Pro Logic II makes no limitation for the cutoff frequency of the surround treble and enables stereo surround sound This receiver provides two types of Dolby Pro Logic II modes Pro Logic II Movie PLII MOVIE and Pro Logic II Music PLII MUSIC When Dolby Pro Logic is activated the DO PRO LOGIC II indicator lights up on the display PLII MOVIE Suitable for playing any Dolby Surround encoded software You can enjoy a sound field very close to the one created with discrete 5 1 channel sounds PLII MUSIC Suitable for playing any 2 channel stereo software You can enjoy wide and deep sounds DTS DTS is another digital signal compression method developed by Digital Theater Systems Inc and enables multi channel encoding and decoding 1ch up to 6 1ch When DTS signal is detected through the digital input the L dts indicator lights up on the display DTS Digital Surround DTS Digital Surround DTS is another discrete 5 1 channel dig
42. 42 AC power cord 16 DIGITAL OUT terminal 16 SURROUND BACK SPEAKERS terminals 10 SURROUND SPEAKERS terminals 10 CENTER SPEAKER terminals 10 FRONT SPEAKERS 1 terminals 10 FRONT SPEAKERS 2 terminals 10 Earth ground terminal 11 RX 7O30VBK RX 7032VSL 1 DIGITAL IN terminals 16 Coaxial DIGITAL 1 DVD Optical DIGITAL 2 CD DIGITAL 3 TV DIGITAL 4 CDR AUDIO input output jacks 12 15 e Input IN FRONT CENTER SUBWOOFER SURR REAR TV SOUND DBS IN VCR IN PLAY TAPE CDR IN PLAY CD IN Output VCR OUT REC TAPE CDR OUT REC S VIDEO and composite VIDEO input output jacks 14 15 e Input DVD IN TV SOUND DBS IN VCR IN PLAY Output VCR OUT REC MONITOR OUT FM AM ANTENNA terminals 8 SUBWOOFER OUT jack 10 COMPONENT VIDEO input output jacks 14 15 e Input DVD IN DBS IN e Output MONITOR OUT COMPU LINK 4 SYNCHRO terminals 41 AV COMPULINK III terminals 42 AC power cord 16 DIGITAL OUT terminal 16 SURROUND BACK SPEAKERS terminals 10 SURROUND SPEAKERS terminals 10 CENTER SPEAKER terminals 10 FRONT SPEAKERS 0 terminals 10 FRONT SPEAKERS 2 terminals 10 Q Supplied x Not supplied PREOUT jacks Video jacks input output CC Converter Selectable source RX 8030VBK Composite video 4 3 S video 4 3
43. 6MUSIC NEO 6CINMA For Dual Mono software you can select the channel you listen to See page 29 SPEAKERS 1 voume 111 To adjust the speaker output level see pages 32 and 33 To cancel the Surround mode Press SURROUND DSP OFF or SURR DSP OFF on the remote control SURR OFF appears on the display 37 Bl Using the DSP Modes This unit activates a variety of DSP modes automatically The basic settings and adjustments stored see pages 25 to 33 are applied automatically Reproducing the Sound Field The sound heard in a concert hall club etc consists of direct sound and indirect sound early reflections and reflections from behind Direct sounds reach the listener directly without any reflection On the other hand indirect sounds are delayed by the distances of the ceiling and walls These direct sounds and indirect sounds are the most important elements of the acoustic surround effects The DSP modes can create these important elements and give you a real being there feeling Reflections from behind Early reflections Introducing the DSP Modes The DSP modes include the following modes DAP Digital Acoustic Processor modes HALL 1 HALL 2 LIVE CLUB DANCE CLUB PAVILION THEATER 1 THEATER 2 ALL CH STEREO MONO FILM 3D HEADPHONE Mode You can also enjoy the DSP effect except All Channel Stereo mode through the headp
44. APPARATUS ICES 003 OF THE DEPARTMENT OF COMMUNICATIONS CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS NUMERIQUES DE CLASSE B PRESCRITES DANS LA NORME SUR LE MATERIEL BROUILLEUR APPAREILS NUMERIQUES NMB 003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS m Table of Contents Introduction 2 2 exten etre en ite dad 2 Parts Identification esee 3 Remote Control 3 Front Panel mettere 4 Rear Panel Getting 8 Before Installation 2 oreet eot 8 Checking the Supplied Accessories e 8 Putting Batteries in the Remote Control 8 Connecting the FM and AM Antennas 8 Connecting th Speakers irent ect hbri 9 Connecting Audio Video Components sss 11 Analog Connections redet Re 11 Bi Digital Connections 5 nere rr ect 16 Connecting the Power Cord 2 erret 16 Basic Operations 17 Daily Operational Procedure rte 17 Turning On the POWET anterior ete ce tte eia 17 Selecting the Source to Play retener once 17 Adjusting the Volume
45. AV COMPU LINK remote control system cannot operate properly See page 42 m For the DVD player VIDEO IN DVD Select one of the following COMPNT Select when connecting the DVD player to the component video input jacks S C Select when connecting the DVD player to the composite video or S video input jacks m For the DBS tuner VIDEO IN DBS Select one of the following COMPNT Select when connecting the DBS tuner to the component video input jacks S C Select when connecting the DBS tuner to the composite video or S video input jacks 30 Select one of the following ON Select to store the volume level separately for each source The ONE TOUCH OPERATION indicator lights up on the display This receiver memorizes the volume level when you change the source or when you change the source name OFF Select this not to store the volume level To recall the volume level With the ONE TOUCH OPERATION indicator lit the volume level for the currently selected source is recalled when the source is selected To cancel the One Touch Operation Set One Touch Operation to OFF so that the ONE TOUCH OPERATION indicator goes off Bw Adjusting Sound You can make sound adjustment to your preference after completing basic setting Basic Setting Items On the following pages you can adjust the items listed below You can adjust only the items applicable to the current sound mode
46. Adjustable range 0 to 0 5 33 si Using the Surround Modes This unit activates a variety of Surround modes automatically The basic settings and adjustments stored see pages 25 to 33 are applied Reproducing Theater Ambience Introducing the Surround Modes In a movie theater many speakers are located on the walls to reproduce impressive multi surround sounds reaching you from all directions With these many speakers sound localization and sound movement can be expressed Surround modes built in this receiver can create almost the same surround sounds as you can feel in a real movie theater with only five to seven speakers plus subwoofer IH ID ID IL 0 oO ID ID ID ID ID ID ID idi Wem 7 Left front speaker Center speaker Right front speaker L C R M Left surround Right surround speaker LS speaker RS Surround back speakers LSB RSB 34 Dolby Digital Dolby Digital is a digital signal compression method developed by Dolby Laboratories and enables multi channel encoding and decoding 1ch up to 5 1ch When Dolby Digital signal is detected through the digital input the indicator lights up on the display Dolby Digital 5 1CH
47. As the number increases the DAP effect becomes stronger Normally select 3 initial setting Adjustable range 1 to 5 ROOMSIZE Adjust the virtual room size As the number increases the interval between reflections increases so that you will feel as if you were in a larger room Normally select 3 initial setting Adjustable range 1 to 5 LIVENESS For Pro Logic Adjust the liveness effect As the number increases the attenuation level of reflections over time decreases so that acoustics change from Dead to Live Normally select 3 initial setting Adjustable range 1to 5 II Music only PANORAMA Select ON to add wraparound sound effect with side wall image Initial setting OFF CNTR WIDTH Adjust the center channel localization between the center speaker and the left right speakers As the number increases the center channel sound moves toward the left and right speakers Normally select 3 initial setting Adjustable range OFF and 1 to 7 DIMENSION Adjust sound localization position As the number increases the sound localization moves towards forward from backward Normally select 4 initial setting Adjustable range 1 to 7 For Neo 6 Music only CNTR GAIN Adjust the sound localization of the center channel As the number increases center channel will be localized clearly Normally select 0 2 initial setting
48. By pressing CONTROL repeatedly you can select VCR 1 TAPE CDR or CDDSC as the source When you press one of the buttons listed above the remote operation mode appears on the operation mode display for about two hours VCR You can always perform the following operations VCR 1 I for RX 8030VBK or VCR I for RX 7030VBK Turn on or off a VCR For RX 8030VBK After pressing VCR 1 or selecting VCR 1 by pressing CONTROL repeatedly you can perform the following operations on a VCR For RX 7030VBK After pressing VCR or VCR CONTROL you can perform the following operations on a VCR 1 9 0 Select the TV channels on a VCR gt Start playing REW Rewind a tape FF Fast wind a tape Stop playing or recording Pause playing To resume press REC PAUSE Enter recording pause by pressing this button To start recording again press this button then CH Change the TV channels on the VCR Note You can use either VCR 1 for RX 8030VBK or VCR for RX 7030VBK or the control button CONTROL for RX 8030VBK or VCR CONTROL for RX 7030VBK to activate the buttons listed above If you press one of the source selection buttons the playing source also changes On the other hand pressing the control button does not change the playing source DVD player After pressing DVD or DVD MULTI you can perform the following operations on a DVD player Start playing
49. COMPU LINK jacks can use either one If it has only one COMPU LINK jack connect it so that it is the last item in the series of components To operate the target component using the COMPU LINK remote control system set the source name correctly if required See page 21 Refer also to the manuals supplied with your audio components This remote control system allows you to use four functions listed below Remote Control through the Remote Sensor on the Receiver You can control the connected audio components through the remote sensor on the receiver using this remote control Aim the remote control directly at the remote sensor on the receiver For details see pages 44 and 45 Automatic Source Selection When you press the play B button on a connected component or on its own remote control the receiver automatically turns on and changes the source to the component On the other hand if you select a new source on the receiver or on the remote control the selected component begins playing immediately In both cases the previously selected source continues playing without sound for a few seconds For RX 7030VBK RX 7032VSL You cannot use the COMPU LINK remote control system to operate the MD recorder Automatic Power On Off Standby on the COMPU LINK 3 and COMPU LINK 4 The connected components turn on and off standby along with the receiver ossible with When you turn on the receiver one of the c
50. LFE Select to transmit only the LFE signals while playing Dolby Digital and DTS software and the bass elements of small speakers through the subwoofer LFE MAIN Select to always add the bass elements of the front speaker channels MAIN to the above LFE setting and to transmit them through the subwoofer Note If you have selected NO for the subwoofer this function is not available Crossover frequency CROSS OVER When you use a subwoofer you can select the cutoff frequency for the small speakers used Select one of the crossover frequency levels according to the size of the small speaker connected 80Hz Select when the cone speaker unit built in the speaker is about 12 cm 4 3 4 inches 100Hz Select when the cone speaker unit built in the speaker is about 10 cm 3 16 inches 120Hz Select when the cone speaker unit built in the speaker is about 8 cm 3 3 16 inches 150Hz Select when the cone speaker unit built in the speaker is about 6 cm 2 s inches Notes If you have selected LARGE for all activated speakers see page 27 this function is fixed to OFF e Crossover frequency is not valid for the DVD MULTI playback All Channel Stereo HEADPHONE and 3D HEADPHONE mode m Low frequency effect attenuator LFE ATTENUATE If the bass sound is distorted while playing back software encoded with Dolby Digital or DTS set the LFE level to eliminate distortion
51. OUT ON OFF button 19 10 PHONES jack 19 1 EX ES button 37 Display Window ia Display Window DUAL indicator 35 ANALOG indicator 20 DIGITAL AUTO indicator 20 96 24 indicator 35 MULTI indicator 40 DO PRO LOGIC indicator 34 OO PRO LOGIC II indicator 35 TUNED indicator 23 STEREO indicator 23 24 NEO 6 indicator 35 AUTO MUTING indicator 24 VIRTUAL SB Surround Back indicator 34 35 ONE TOUCH OPERATION indicator 30 eeoomvo 20 21 22 INPUT ANALOG button 20 INPUT ATT button 20 MIDNIGHT MODE button 20 INPUT DIGITAL button 20 TUNER CONTROL buttons FM AM TUNING A buttons 23 e FM AM PRESET A buttons 23 24 FM MODE button 24 MEMORY button 23 Only for RX 8030VBK VIDEO input jacks 13 DIGITAL optical terminal S VIDEO jack VIDEO jack AUDIO L R jacks SETTING button 27 QUICK SPEAKER SETUP button 25 MULTI JOG control 25 27 31 PUSH SET button 25 27 31 EXIT button 27 31 ADJUST button 31 ANALOG DIRECT button and lamp 21 TUNED AUTO MUTING ONETOUCH OPERATION SLEEP IU PRO LOGICI NEO 6 VIRTUAL SB MIDNIGHT MODE DIGITAL EQ DSP 3D PHONIC HEADPHONE 1 2 BASS BOOST
52. Press CC CONVERTER so that the lamp on the button lights up Each time you press the button CC Converter turns on and off the lamp goes off alternately Note You cannot use this function while Analog Direct is in use If you turn on Analog Direct while this function is in use this function will be canceled Changing the Source Name When you have connected an MD recorder to the TAPE MD jacks or a DBS tuner to the TV SOUND DBS jacks on the rear panel change the source name which will be shown on the display uve c 5 m c o o When changing the source name from TV to DBS 1 Press TV SOUND DBS Make sure appears on the display 2 Press and hold TV SOUND DBS until ASSGN DBS appears on the display SPEAKERS 1 voume 21 Note When connecting a DBS tuner to the TV SOUND DBS IN jacks change the source name to DBS which will be shown on the display when selected as the source Otherwise you cannot view any picture from DBS tuner For RX 8030VBK When changing the source name from TAPE to MD 1 Press TAPE MD Make sure appears on the display 2 Press and hold TAPE MD until ASSGN MD appears on the display For RX 7030VBK When changing the source name from TAPE to CD
53. Select one of the following OdB Normally select this 10dB Select when the bass sound is distorted Selecting main or sub channel DUAL MONO Select the playback sounds channel MAIN Select to play back the main channel Ch1 Signal indicator L lights up while playing back this channel SUB Select to play back the sub channel Ch2 Signal indicator lights up while playing back this channel ALL Selectto play back both the main and sub channels Ch1 Ch2 Signal indicators and light up while playing back these channels Notes The Dual Mono format is not identical with bilingual broadcasting or the MTS Multichannel Television Sound format used for TV programs So this setting does not take effect while watching bilingual or MTS programs Dual Mono signals can be heard from the following speakers L left front speaker R right front speaker and C center speaker with respect to the current Surround setting With Surround Activated Dual Mono Without Surround Center speaker setting Setting SMALL LARGE Ch 1 Ch 2 Ch 1 Ch 2 Setting the Digital Input Terminals When you use the digital input terminals register which components you have connected to the digital input terminals m Digital coaxial terminal DGTL IN COAX Set the component connected to the digital coaxial terminal DIGITAL IN 1 F
54. The preset settings such as preset channels and sound adjustment may be erased in a few days in the following cases When you unplug the power cord When a power failure occurs CAUTIONS Do not touch the power cord with wet hands Do not pull on the power cord to unplug the cord When unplugging the cord always grasp the plug so as not to damage the cord nu Basic Operations The following operations are commonly used when you play any sound sources Operations hereafter will be explained using the buttons on the front panel You can also use the buttons on the remote control for the same functions if they have the same and similar names marks Daily Operational Procedure Selecting the Source to Play Turn on the power See Turning On the Power below Select the source See Selecting the Source to Play to the right Adjust the volume See Adjusting the Volume on page 18 Select the surround or DSP modes See Activating the Surround Modes page 37 and Activating the DSP Modes page 39 Y C r c o o eco 000000 o o oo Press 0 1 STANDBY ON or AUDIO con the remote control The STANDBY lamp goes off The name of the current source and Surround DSP mode appear on the display Current so
55. VCR 2 for RX 8030VBK or VCR for RX 7030VBK For RX 8030VBK You can connect two VCRs one to the VCR 1 jacks and the other to the VCR 2 jacks If your VCR has an AV COMPU LINK jack connect it to the VCR 1 jack so that you can use the AV COMPU LINK remote control system To audio input To audio output To S video output To composite video output To S video input To composite video input RX 8030VBK n m o O o For RX 7030VBK To audio input To audio output To S video output To composite video output To S video input To composite video input RX 7030VBK nj m O w gt VCR 14 TV and or DBS tuner To listen to the sound after connection press TV SOUND DBS or TV DBS on the remote control tOO G am DOYO C3 RX 8030VBK RX 7030VBK When connecting MONITOR n the TV to the E AUDIO jacks TV SOUND DBS IN DO NOT connect the TV s video output to these video input jacks Connect the TV to appropriate MONITOR OUT jacks to view the playback picture from any other connected video components To audio output To component video input To S video input To composite video input
56. VCR and or DVD player to the TV using one of the following three ways When using the AV COMPU LINK remote control system set the component video input for the DVD player and the DBS tuner correctly see Setting the Component Video Input on page 30 otherwise the correct input for this receiver will not be selected on the TV When connecting the source equipment to the receiver through the S video jacks connect this receiver to the TV s Video Input 1 jack using S video cables Source RX 8030VBK equipment S video cord RX 7030VBK S video cord To video Input 1 When connecting the source equipment to the receiver through the composite video jacks connect this receiver to the TV s Video Input 2 jack composite video input using composite video cables Source RX 8030VBK TV equipment Composite RX 7030VBK Composite video cord video cord To video Input 2 42 When connecting the source equipment to the receiver through the component video jacks connect this receiver to the TV s Video Input 2 jack component video input using component video cables Source RX 8030VBK Component RX 7030VBK Component video cord video cord To video Input 2 1 If you have already plugged your VCR DVD player TV and this receiver into the AC outlets unplug their AC power cords first 2 Connect your VCR DVD player TV and this receiver using the cables with the monaural mini plugs not
57. WITHOUT LIMITATION DAMAGE TO TAPES RECORDS OR DISCS RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANT ABILITY AND FITNESS FOR PARTICULAR PURPOSE ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts so these limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state JVC COMPANY OF AMERICA 1700 Valley Road DIVISION OF JVC AMERICAS CORP Wayne NJ 07470 Seb Ob bb bb bbb bt bbb bt bob bob bot bot bb ot bbb bb bo bot bob bobo bob bb ot bob bob bob bbb bob ob bb bt bob bb bbb bb bb bt ab bb bt bbb Je RR OR bb bb bt bb bb Ot bb bb tb bbb bot bbb bt bb bb bbb bb bt bob bb bob bb bb bbb bbb bob boi bb bb bb bb bbb bok bb bb bbb bbe FI ID II II III 92 2492 242 I IAA AAA 9 2 2 AA AA AAA AAA SAAS ASA A AA SAAS AS ACS ACA SAAS ACS SAS ACSA SO S S SO ODE REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY THIS WARRANTY DOES NOT APPLY FOR DETAILS OF REFURBISHED PRODUCT WARRANTY PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT For customer use Enter below the Model No which is located either on the rear bottom or side of the cabinet Retain this information fo
58. analog sources OC 29 0000 9 mm m Press CC CONVERTER so that the lamp on the button lights up Each time you press the button CC Converter turns on and off the lamp goes off alternately Note You cannot use this function while Analog Direct is in use If you turn on Analog Direct while this function is in use this function will be canceled When you have connected an MD recorder to the TAPE MD jacks or a DBS tuner to the TV SOUND DBS jacks on the rear panel change the source name which will be shown on the display o eco 000000 o o oo 000 J amp When changing the source name from TV to DBS 1 Press TV SOUND DBS Make sure TV appears on the display 2 Press and hold TV SOUND DBS until ASSGN DBS appears on the display SPEAKERS 1 voume IZ I Note When connecting a DBS tuner to the TV SOUND DBS IN jacks change the source name to DBS which will be shown on the display when selected as the source Otherwise you cannot view any picture from DBS tuner For RX 8030VBK When changing the source name from TAPE to MD 1 Press TAPE MD Make sure TAPE appears on the display 2 Press and hold TAPE MD until ASSGN MD appears on the display F
59. cable not supplied and or component video cable not supplied By using these jacks you can get better picture quality in the order Component video gt S video gt Composite video If your video components have an AV COMPULINK jack See also page 42 for detailed information about the connection and the AV COMPU LINK remote control system IMPORTANT This receiver is equipped with the following video jacks composite video S video and component video jacks You can use any of the three to connect a video component However the video signals from one type of these input jacks are transmitted only through the video output jacks of the same type Therefore if a recording video component and a playing video component are connected to the receiver through the video jacks of different type you cannot record the picture In addition if the TV and a playing video component are connected to the receiver through the video jacks of different type you cannot view the playback picture on the TV RX 8030V ONLY Video camera To listen to the sound after connection press VIDEO The VIDEO input jacks on the front panel inside the front door are convenient when connecting and disconnecting the component frequently To composite video PA output To S video output To optical digital output 1 630 90 DIGITAL S VIDEO VIDEO L AUDIO R VIDEO Video camera
60. connected speakers SURR SPEAKER Register your surround speaker size 27 L R RS SB SBACK SPEAKER Register your surround back NONE speaker size 27 NONE SBACK OUT Register the number of the NONE connected surround back speakers 27 NONE DIST UNIT Select the measuring unit for the NONE speaker distance 28 NONE FRONT DISTANCE Register the distance from you front NONE speakers to your listening point 28 CNTR DISTANCE Register the distance from you center NONE speaker to your listening point 28 SMALL SURR DISTANCE Register the distance from you SMALL surround speakers to your listening SMALL point 28 SMALL SBACK DISTANCE Register the distance from you surround back speaker s to your This setting is applied to the both speakers listening point 28 S WFR OUTPUT Select sounds emitted from the Room size and the speaker distance subwoofer 28 According to the selected room size speaker distance for each CROSS OVER Select the cutoff frequency to the activated speaker is set as follows subwoofer 28 LARGE Speaker Distance LFE ATTENUATE Attenuate the bass LFE sounds 29 3 0 m 10 ft DUAL MONO Select the Dual Mono sound channel 29 3 0 m 10 ft DGTL IN COAX Select the component connected to 3 0 m 10 ft digital coaxial terminal 29 10f DGTL IN O
61. is automatically reset to DGTL AUTO To select the analog input mode again Press INPUT ANALOG or press ANALOG DIGITAL INPUT on the remote control repeatedly until ANALOG appears on the display The ANALOG indicator lights up 20 MID NIGHT 2 Select when you want to apply the compress effect fully useful at midnight MID NIGHT OFF Select when you want to enjoy surround with its full dynamic range no effect applied Notes e f Analog Direct is in use Midnight Mode is temporarily canceled Midnight Mode is not valid for DVD MULTI playback mode When the input level of the analog source is too high the sounds will be distorted If this happens you need to attenuate the input signal level to prevent the sound distortion Once you have made adjustment it is memorized for each analog source Attenuating the Input Signal doo 0 Q2 S3 Press and hold INPUT ATT INPUT ANALOG so that the INPUT ATT indicator lights up on the display Each time you press and hold the button the input attenuator mode turns ON or off NORMAL Note This function is not valid when DVD MULTI is selected or when Analog Direct is activated Turning Analog Direct On and Off Changing the Source Name You can enjoy the sound closer to the original source by overriding
62. min RMS driven into 8 Q at 1 kHz with no more than 0 8 total harmonic distortion Audio Audio Input Sensitivity Impedance 1 kHz PHONO IN MM 2 5 mV 47 DVD IN VCR 1 IN VCR 2 IN TV SOUND DBS IN VIDEO IN 200 mV 47 CD IN CDR IN TAPE MD IN 200 mV 47 Audio Input DIGITAL IN Coaxial DIGITAL 1 DVD 0 5 V p p 75 Q Optical DIGITAL 2 CD DIGITAL 3 TV DIGITAL 4 CDR 21 dBm to 15 dBm 660 nm 30 nm Corresponding to Linear PCM Dolby Digital and DTS Digital Surround with sampling frequency 32 kHz 44 1 kHz 48 kHz Audio Output Level PRE OUT 1V Recording Output Level VCR 1 OUT VCR 2 OUT CDR OUT TAPE MD OUT 200 mV Digital output Optical DIGITAL OUTPUT Signal wave length 660 nm Output level 21 dBm to 15 dBm Signal to Noise Ratio 66 IHF 78 IHF PHONO IN 70 dB 78 dB at REC OUT DVD IN VCR 1 IN VCR 2 IN TV SOUND DBS IN VIDEO 87 dB 80 dB CD IN CDR IN TAPE MD IN 87 dB 80 dB Frequency Response 8 Q PHONO IN 20 Hz to 20 kHz x1 dB DVD IN VCR 1 IN VCR 2 IN TV SOUND DBS IN VIDEO 20 Hz to 100 kHz 1 dB 3 dB CD IN CDR IN TAPE MD IN 20 Hz to 100 kHz 1 dB 3 dB RIAA Phono Equalization 1 0 dB 20 Hz to 20 kHz Equalization 5 bands 63 Hz 250 Hz 1 kHz 4 kHz 16 kHz x8 dB Bass boost 6 dB 1 0 dB at 100 Hz Video Video Input Sensitivity Impedance Composite video DVD IN VCR 1 IN VCR 2 IN TV SOUND DBS IN VIDEO 1 V p p 75
63. mode to the appropriate position either Video Input 1 or Video Input 2 so that you can view the playback picture Notes e When you select TV as the source on the receiver you cannot see the menu on the TV screen since the AV COMPU LINK remote control system automatically changes the TV s input mode to the TV tuner This function does not work when you connect this receiver and the TV with the AV COMPU LINK EX terminal using a component video cable In this case reconnect the TV referring to case 1 or case 2 on page 42 Automatic Power On Off The TV VCR and DVD player turn on and off along with the receiver When you turn on the receiver If the previously selected source is 1 for RX 8030VBK or VCR for RX 7030VBK RX 7032VSL the TV and VCR will turn on automatically If the previously selected source is DVD or DVD MULTI the TV and DVD player will turn on automatically If the previously selected source is any video source other than the above only the TV will turn on automatically When you turn off the receiver the TV VCR and the DVD player will turn off Note If you turn off the receiver while recording on the VCR the VCR will not turn off but continue recording 43 Operating JVC s Audio Video Components You can operate JVC s audio and video components with this receiver s remote control since control signals for JVC s components are preset in the remot
64. ra eadphones you can listen to the front channels le F To left right front channel audio output g Y G To left right surround channel audio output Note When connecting a DVD player to the component video input jacks make the component video input setting correctly See page 30 for details 40 E COMPU LINK Remote Control System The COMPU LINK remote control system allows you to operate JVC s audio components through the remote sensor on the receiver To use this remote control system you need to connect JVC s audio components through the COMPU LINK SYNCHRO jacks see below in addition to the connections using cables with RCA pin plugs see pages 12 and 13 Make sure that the AC power cords of these components are unplugged before connection Plug the AC power cords only after all connections are complete RX 8030VBK RX 7030VBK gt SEE EE CD recorder AU Cassette deck or CD recorder Cassette deck or MD recorder COMPU LINK 4 SYNCHRO Sum jo mi Se Notes There are four versions of COMPU LINK remote control system This receiver is equipped with the fourth version COMPU LINK 4 This version is added systematic operations with the CD recorder to the previous version COMPU LINK 3 e If your audio component has two COMPU LINK jacks you can use either one If it has only one COMPU LINK jack connect it so that it is the last item in the ser
65. see Selecting the Analog or Digital Input Mode on page 19 Digital input terminals You can connect any digital components having coaxial or optical digital output terminal Digital coaxial cable not supplied between digital coaxial terminals Digital optical cable not supplied DIGITAL IN When the component has a digital coaxial output terminal connect it to the DIGITAL 1 DVD terminal using a digital coaxial cable not supplied DIGITAL 1 DVD When the component has a digital optical output terminal connect it to the DIGITAL 2 CD DIGITAL 3 TV or DIGITAL 4 CDR terminal using a digital optical cable not supplied DIGITAL N Before connecting a digital optical cable unplug the tecti lug protective plug en DIGITAL 4 CDR Notes When shipped from the factory the DIGITAL IN terminals have been set for use with the following components DIGITAL 1 coaxial For DVD player DIGITAL 2 optical For CD player DIGITAL 3 optical For digital TV broadcast tuner DIGITAL 4 optical For CD recorder When you want to operate the CD player or CD recorder or MD recorder only for RX 8030VBK using the COMPU LINK remote control system connect the target component also as described in Analog Connections see pages 12 and 13 e When you want to operate a DVD player using the A
66. speaker size setting either SMALL or LARGE Select one of the following LFE Select to transmit only the LFE signals while playing Dolby Digital and DTS software and the bass elements of small speakers through the subwoofer LFE MAIN Select to always add the bass elements of the front speaker channels MAIN to the above LFE setting and to transmit them through the subwoofer Note If you have selected NO for the subwoofer this function is not available Crossover frequency CROSS OVER When you use a subwoofer you can select the cutoff frequency for the small speakers used Select one of the crossover frequency levels according to the size of the small speaker connected 80Hz Select when the cone speaker unit built in the speaker is about 12 cm 4 inches 100Hz Select when the cone speaker unit built in the speaker is about 10 cm 3 16 inches 120Hz Select when the cone speaker unit built in the speaker is about 8 cm 3 2 16 inches 150Hz Select when the cone speaker unit built in the speaker is about 6 cm 2 s inches Notes If you have selected LARGE for all activated speakers see page 27 this function is fixed to OFF e Crossover frequency is not valid for the DVD MULTI playback All Channel Stereo HEADPHONE and 3D HEADPHONE mode m Low frequency effect attenuator LFE ATTENUATE Setting the Digital Input Terminals If the bass sound is dis
67. standby mode To turn off the power completely unplug the AC power cord Selecting the Source to Play uve co c o o c ES 000000 o o oo Press one of the source selection buttons The selected source name and the previously selected Surround DSP mode also appear on the display Selected source name and current Surround DSP mode appear TUNED STEREO AUTOMUTING ONETOUCH OPERATION SLEEP DOPROLOGICI NEO 6 VIRTUAL SB MIDNIGHT MODE DIGITAL EQ DSP 3D PHONIC HEADPHONE SPEAKERS 1 2 BASSBOOST input 11121 volume II II a o o o o o o o o o o DvbMULm 1 SOUND PHONO cb FM AM the unit The lamp on the selected source lights up ex when DVD is selected as the source DVDMULTI DVD CD FM AM C 0C oC oC D VCR1 VCR2 CDR APE MD TvDBS VIDEO PHONO On the remote For RX 7030VBK DVD MULTI DVD VCR TV SOUND DBS TAPE CDR FM AM On the unit DVD MULTI DVD CD FM AM TOE Ca ue CODCI 7 TV DBS VCR TAPE CDR On the remote Notes For RX 8030VBK When connecting an MD recorder to the TAPE MD jack and a DBS tuner to the TV SOUND DBS jacks change the source names shown on
68. surround back speaker SURR L Left surround speaker Back to the beginning 3 Select a speaker you want to adjust To select the left front speaker press FRONT L To select the center speaker press CENTER To select the right front speaker press FRONT R To select the right surround speaker press SURR R To select the surround back speaker press SURR BACK To select the left surround speaker press SURReL 4 Press LEVEL or LEVEL to adjust the speaker output level 10 dB to 10 dB 5 Repeat steps 3 and 4 to adjust the other speaker s output levels 6 Press TEST again to stop the test tone Adjusting the Sound Parameters for the Surround and DSP Modes You can adjust the Surround and DSP sound parameters to your preference When center speaker is set to NONE CTR TONE CNTR WIDTH and CNTR GAIN are not available Adjustable parameters You can adjust the following parameters For Surround DAP and All Channel Stereo modes when the center speaker is connected This setting is common to all surround modes and is memorized separately for DSP modes CTR TONE Adjust the center tone As the number increases the dialogue becomes clearer so that the human voices change from soft to sharp Normally select 3 initial setting Adjustable range 1 to 5 For DAP modes Once you have made an adjustment it is memorized for each DAP mode EFFECT Adjust t
69. this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by the manufacturer for compliance could void the users authority to opratethe equipment Note to CATV system installer This reminder is provided to call the CATV system installer s attention to Section 820 40 of the NEC which provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical For Canada pour Le Canada CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT ATTENTION POUR EVITER LES CHOCS ELECTRIQUES INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPA RATUS AS SET OUT IN THE INTERFERENCE CAUSING EQUIPMENT STANDARD ENTITLED DIGITAL
70. to easily and quickly register the speaker size and speaker distance according to your listening room to create the best possible surround effect You can also register each speaker s information manually For details see page 27 JVC e bi d c o c Ho Before you start remember There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again On the front panel 1 Press QUICK SPEAKER SETUP SETUP and SPEAKERS appear on the display then the initial setting for the total number of the connected speakers channels appears SPEAKERS 1 voume IZ SPEAKERS 1 voume IZ 2 Turn MULTI JOG to select an appropriate number of the connected speakers speaker channel number The speaker channel number changes as follows For the details of speaker channel number see Speakers channels number and the size on page 26 SPEAKERS 1 voume IZ I 2 0CH 44CH 7 0CH 2 1CH 3 0CH 3 1CH 4 0CH 5 0CH 5 1CH 6 0CH 6 1CH 7 1CH Back to the beginning 6 0CH is the initial setting 3 Press in MULTI JOG PUSH SET ROOM SIZE appear on the display then the initial room size setting appears voume I 21 voume
71. to the digital input mode 3 Jvc s o 6 Sess Z c o o c oo cs EN Before you start remember The digital input terminal setting should be correctly done for the sources you want to select the digital input mode see Setting the Digital Input Terminals on pages 29 and 30 1 Press one of the source selection buttons for which you want to change the input mode For RX 8030VBK DVD VIDEO TV SOUND DBS CD CDR or TAPE MD For RX 7030VBK RX 7032VSL DVD TV SOUND DBS CD or TAPE CDR If TAPE is selected as the source digital input mode is not available To change the source name see Changing the Source Name on page 21 Continued on the next page 19 2 Press INPUT DIGITAL or ANALOG DIGITAL INPUT on the remote control to select DGTL AUTO The DIGITAL AUTO indicator lights up on the display SPEAKERS 1 voume I 21 When selecting DGTL AUTO the following indicators indicate the digital signal format of the incoming signal Lights up when Linear PCM signals come in Lights up when Dolby Digital signals come in Lights up when DTS signals come in Setting the Dynamic Range You can enjoy a powerful sound at night using the Midnight Mode o o o c o o c 20000 o a Press MIDNIGHT MODE so tha
72. wiring If OVERLOAD does not disappear unplug the AC power cord then plug it back again If speaker wiring is not short circuited contact your dealer The STANDBY lamp lights up after turning on the power and soon the receiver turns off again into standby mode The receiver is overloaded because of a high voltage Press 9 1 STANDBY ON on the front panel to turn off the receiver After unplugging the AC power cord consult your dealer Remote control does not work There is an obstruction between the remote sensor on the receiver and the remote control Remove the obstruction Batteries are weak Replace batteries See page 8 Remote control does not work as you intend 50 An incorrect remote control operation mode is selected Select the correct remote control operation mode See pages 44 to 49 Specifications RX 8030VBK Amplifier Output Power At Stereo operation Front ch 130 W per channel min RMS driven into 8 20 Hz to 20 kHz with no more than 0 08 total harmonic distortion At Surround operation Front ch 130 W per channel min RMS driven into 8 Q at 1 kHz with no more than 0 896 total harmonic distortion Center ch 130 W min RMS driven into 8 Q at 1 kHz with no more than 0 8 total harmonic distortion Surround ch 130 W per channel min RMS driven into 8 Q at 1 kHz with no more than 0 896 total harmonic distortion Surround Back ch 130 W
73. you want to operate the CD player or CD recorder or MD recorder only for RX 8030VBK using the COMPU LINK remote control system connect the target component also as described in Analog Connections see pages 12 and 13 When you want to operate a DVD player using the AV COMPU LINK remote control system see page 42 connect the DVD player also as described in Analog Connections see page 15 16 Digital output terminal You can connect any digital components which have an optical digital input terminal Digital optical cable not supplied between digital optical terminals When the digital recording equipment such as an MD recorder and CD recorder has a digital optical input terminal connecting it to the DIGITAL OUT terminal enables you to perform digital to digital recording PCM DOLBY DIGITAL DTS DIGITAL OUT Note The digital signal format transmitted through the DIGITAL OUT terminal is the same as that of the input signal This means that when the DTS Digital Surround signals are input the DTS Digital Surround signals are transmitted Connecting the Power Cord Before plugging the receiver into an AC outlet make sure that all connections have been made Plug the power cord into an AC outlet Keep the power cord away from the connecting cables and the antenna The power cord may cause noise or screen interference Note
74. 0 THEATER 2 Reproduces the spatial feeling of a small theater where the seating capacity is about 300 The built in Dolby Pro Logic Il decoder is activated when playing back 2 channel analog or digital source The DO PRO LOGIC TI indicator lights up When using the DAP mode the sounds come out of all the connected and activated speakers If surround speakers are set to NONE in the speaker setting JVC s original 3D PHONIC processing which has been developed to create the surround effect through the front speakers only is used The 3D PHONIC indicator lights up on the display ALL Channel Stereo mode Activating the DSP Modes This mode can reproduce a larger stereo sound field using all the connected and activated speakers This mode cannot be used Activating one of the DSP modes for a source automatically without activating the surround speakers recalls the memorized settings and adjustments see pages 25 to If the front speakers are deactivated All Channel Stereo 33 cannot be selected You can also use the buttons on the remote control for the same functions Jvc 2 i ay o o c CE aaoi 1 Select and play any sound source 2 Press DSP repeatedly until the DSP mode you want appears on the display Each time you press the button the DSP modes change a
75. 0 286 V p p 75 Q 1 V p p 75 0 7 V p p 75 Video Output Level Composite video VCR OUT MONITOR OUT S video VCR OUT MONITOR OUT Y luminance C chrominance burst Component video MONITOR OUT Y luminance 1 75 Q 1 75 Q 0 286 V p p 75 Q 1 75 Q 0 7 V p p 75 Q Synchronization Negative Signal to Noise Ratio 45 dB FM tuner IHF Tuning Range Usable Sensitivity Monaural 50 dB Quieting Sensitivity Monaural Stereo Stereo Separation at REC OUT 87 5 MHz to 108 0 MHz 12 8 dBf 1 2 uV 75 16 0 dBf 1 7 uV 75 37 5 dBf 20 5 uV 75 Q 35 dB at 1 kHz AM tuner Tuning Range 530 kHz to 1 710 kHz General AC 120V 60 Hz 320 W 440 VA at operation 2 W in standby mode 435 mm x 157 mm x 425 mm 17 he in x 6 3 16 in x 16 3 4 in 12 1 kg 26 7 lbs Power Requirements Power Consumption Dimensions W x H x D Mass Designs amp specifications are subject to change without notice M D EN FR 2003 VICTOR COMPANY OF JAPAN LIMITED VICTOR COMPANY OF JAPAN LIMITED 0203NHMMDWJEIN
76. 1 voume I SPEAKERS 1 voume I 21 4 Turn MULTI JOG to select an appropriate room size to match to your listening room The room size changes as follows To select your appropriate room size see Room size and the speaker distance on page 26 SMALL MID LARGE Back to the beginning LARGE is the initial setting 5 Press in MULTI JOG PUSH SET COMPLETE appears on the display then goes back to the source indication Speaker configuration settings now become active SPEAKERS 1 voume IZ 21 Note This procedure will not be completed if you stop in the middle of the setting process 25 Speakers channels number and the size Basic Setting Items You can find how each of the speaker size is defined according to the number of connected speakers speaker channel CH number you select In the following tables L stands for left front speaker for On the following pages you can adjust the following items right front speaker C for center speaker LS for left Items To do See page surround speaker RS for right surround speaker SB for SUB WOOFER Register your subwoofer 27 surround back speaker and SUBWFR for subwoofer FRONT SPEAKER Register your front speaker size 27 Subwoofer is counted as 0 1 channel CNTR SPEAKER Register your cen
77. 1 DIMMER button 22 Only for RX 7030VBK RX 7032VSL TAPE CDR CONTROL button 45 Front Panel RX 8030VBK 8 RX 8030VBK m o m m CC CONVERTER DVDMULTI DVD VCR1 VCR2 VIDEO mew RX 7030VBK RX 7030VBK RX 7032VSL RX 7032VSL BASS BOOST DVD MULTI DVD VCR TAPE CDR a FM AM TUNING FM AM PRESET FM MODE MEMORY Inside the front door How to open the front door Press down on PUSH OPEN Front Panel I STANDBY ON button and STANDBY lamp 17 2 e SPEAKERS ON OFF 1 button 19 SPEAKERS ON OFF 2 button 19 3 SURROUND button 37 DSP button 39 SURROUND DSP OFF button 37 39 4 Remote sensor 5 Display window 17 6 For RX 8030VBK Source selection buttons and lamps 17 18 19 21 23 24 37 40 DVD MULTI DVD VCR 1 VCR 2 VIDEO TV SOUND DBS PHONO CD CDR TAPE MD FM AM The lamp above the button for selected source lights up For RX 7030VBK RX 7032VSL Source selection buttons 17 18 19 21 23 24 37 40 DVD MULTI DVD VCR TV SOUND DBS CD TAPE CDR FM AM 7 MASTER VOLUME co
78. 3 TV or DBS 4 CDR Notes back to the beginning The Dual Mono format is not identical with bilingual n broadcasting or the MTS Multichannel Television Sound When DIGITAL IN 1 DGTL IN COAX is set to CD format used for TV programs So this setting does not take 2 DVD 3 TV or DBS 4 CDR effect while watching bilingual or MTS programs 2 DVD 3 TV or DBS 4 MD Dual Mono signals can be heard from the following speakers 2 DVD 3 MD 4 CDR L left front speaker R right front speaker and C center 2 MD 3 TV or DBS 4 CDR speaker with respect to the current Surround setting s back to the beginning With Surround Activated When DIGITAL IN 1 DGTL IN COAX is set to TV or Dual Mono Without Surround Center speaker setting _ pps Setting SMALL LARGE NONE 2 CD 3 DVD 4 C L R 2 CD 3 DVD 4 MD Ch 1 Chi 2 CD 3 MD 4 CDR Ch2 Ch2 2 MD 3 DVD 4 CDR Ch 1 Ch 2 Ch 1 Ch 2 back to the beginning When DIGITAL IN 1 DGTL IN COAX is set to CDR 2 CD 3 TV or DBS 4 DVD 2 CD 3 TV or DBS 4 MD 2 3 MD 4 DVD 2 3 TV or DBS 4 DVD i back to the beginning When DIGITAL IN 1 DGTL IN COAX is set to MD 2 CD 3 TV or DBS 4 CDR 2 CD 3 TV or DBS 4 DVD 2 3 DVD 4 CDR 2 DVD 3 TV or DBS 4 CDR
79. A pin plugs see pages 11 to 19 Aim the remote control directly at the remote sensor the receiver If you use the buttons on the front panel to choose a source the remote control will not operate that source To operate a source with the remote control the source must be selected using source selection buttons on the remote control To operate the target component using the COMPU LINK remote control system set the source name correctly if required See page 21 Refer also to the manuals supplied with your components For RX 8030VBK RX 8030V When you press one of the source selection 19 buttons the remote operation mode appears on the display window for about two hours Buttons Indications FM AM TUNER CD CD CDR CDR PHONO PHONO TAPE MD TAPE gt TAPE 4 CONTROL repeatedly CDDSC CDR lt SOUND SOUND By pressing CONTROL repeatedly you can select VCR 1 TAPE or CDDSC as the source When you press one of the following buttons the remote operation mode appears on the display window for about two hours Buttons Indications FRONT L FRL FRONT R FRR CENTER CTR SURReL SURRL SURR R SURRR SURR BACK SBK SUBWOOFER S WFR DIGITAL EQ EQ 44 Tuner You can always perform the following operations FM AM Alternate between FM and AM After pressing FM AM you can perform
80. CD you can perform the following operations on a CD player gt Start playing aa Return to the beginning of the current or previous track PP Skip to the beginning of the next track Stop playing Pause playing To resume press 1 10 0 10 Select a track number directly For track number 5 press 5 For track number 15 press 10 then 5 For track number 20 press 10 then 10 0 For track number 30 press 10 10 then 10 0 CD changer For RX 8030VBK After selecting CDDSC by pressing CONTROL repeatedly you can perform the following operations on a CD changer For RX 7030VBK After pressing CD DISC you can perform the following operations on a CD changer gt Start playing lt Return to the beginning of the current or previous track gt gt Skip to the beginning of the next track Stop playing or recording Pause playing To resume press gt 1 6 7 P Select the number of a disc installed in a CD changer After pressing CD you can perform the following operations on a CD changer 1 10 0 10 Select a track number directly For track number 5 press 5 For track number 15 press 10 then 5 For track number 20 press 10 then 10 0 For track number 30 press 10 10 then 10 0 Example Selecting disc number 4 track number 12 and starting playback For RX 8030VBK 1 Press CONTROL repeatedly until CDDSC appears on the display win
81. CR or DVD player etc For RX 8030VBK cD FMAM CY CoO o o o o TAPE MD PHONO cD CDR TAPE MD M the unit On the remote For RX 7030VBK RX 7032VSL CD FM AM cD TAPE CDR FM AM TAPE CDR On the unit On the remote Note When you see the picture through the COMPONENT VIDEO jacks you cannot use this function Adjusting the Volume 000 8 the front panel To increase the volume turn MASTER VOLUME clockwise To decrease the volume turn it counterclockwise From the remote control To increase the volume press VOLUME To decrease the volume press VOLUME CAUTION Always set the volume to the minimum before starting any sources If the volume is set at its high level the sudden blast of sound energy can permanently damage your hearing and or ruin your speakers Notes The volume level can be adjusted within the range of 0 minimum to 70 maximum e If you set One Touch Operation to ON see page 30 you do not have to adjust the volume level each time you change the source It is automatically set to the stored level Selecting the Front Speakers Activating and Adjusting the Subwoofer Sound When you have connected two pairs of the front speakers you can select which to use o c o
82. Component video 2 1 DVD MULTI DVD VCR 1 VCR 2 VIDEO TV SOUND DBS PHONO CD CDR TAPE MD FM AM RX 7030VBK RX 7032VSL Composite video 3 2 S video 3 2 Component video 2 1 Color Remote Conirol Display Window RM SRX8030J Black RM SRX7030J Black RM SRX7032U Silver DVD MULTI DVD VCR TV SOUND DBS CD TAPE CDR FM AM nu Getting Started This section explains how to connect audio video components and speakers to the receiver and how to connect the power supply Before Installation General Precautions Be sure your hands are dry Turn the power off to all components Read the manuals supplied with the components you are going to connect Locations nstall the receiver in a location that is level and protected from moisture The temperature around the receiver must be between 5 C and 35 C 23 F and 95 F Make sure there is good ventilation around the receiver Poor ventilation could cause overheating and damage the receiver Handling the receiver Do not insert any metal object into the receiver Do not disassemble the receiver or remove screws covers or cabinet Do not expose the receiver to rain or moisture Checking the Supplied Accessories Check to be sure you have all of the following items which are supplied with the receiver The number in the parentheses indicates quantity of the pieces supplied
83. E To composite video output When using a headphones you can listen to the front channels left F To left right front channel audio output G To left right surround channel audio output Note When connecting a DVD player to the component video input jacks make the component video input setting correctly See page 30 for details 40 COMPU Remote Control System The COMPU LINK remote control system allows you to operate JVC s audio components through the remote sensor the receiver To use this remote control system you need to connect JVC s audio components through the COMPU LINK SYNCHRO jacks see below in addition to the connections using cables with RCA pin plugs see pages 12 and 13 Make sure that the AC power cords of these components are unplugged before connection Plug the AC power cords only after all connections are complete RX 8030VBK RX 7030VBK RX 7032VSL ERN _ ee CD player E CD recorder Cassette deck or MD recorder Cassette deck or CD recorder COMPU LINK 4 SYNCHRO i f um ra a 2 o Notes e There are four versions of COMPU LINK remote control system This receiver is equipped with the fourth version COMPU LINK 4 This version is added systematic operations with the CD recorder to the previous version COMPU LINK 3 e f your audio component has two
84. EX ES will activate an appropriate Surround mode for the current source When an analog or digital 2 channel source is playing you can adjust the EX ES 7 1 channel reproduction mode and store the setting but it will not affect the current source When the source is one to which the EX ES 7 1 channel reproduction cannot be applied you can adjust the setting and store in memory but reproduction channels will remain unchanged mE o o c SE oo J 1 Select and play any source other than DVD MULTI Make sure you have selected the analog or digital input mode Surround modes are not valid for DVD MULTI playback mode 2 Press SURROUND to activate the Surround mode For multi channel digital software except 2 channel and Dual Mono software incoming signals are automatically detected and the appropriate surround mode is activated see page 36 for details DIGITAL AUTO i ure Donanma i RS Ex When DOLBY is activated If the EX ES 7 1 channel reproduction mode has been set to AUTO or ON one of the EX ES 7 1 channel reproduction modes will be activated see the left column For analog sources and digital 2 channel software you can select one of the following Surround modes Each time you press SUR
85. FRL FRONT R FRR CENTER CTR SURR L SURRL SURR R SURRR SURR BACK SBK SUBWOOFER S WFR DIGITAL EQ EQ 44 You can always perform the following operations FM AM Alternate between FM and AM After pressing FM AM you can perform the following operations on a tuner 1 10 0 10 Select a preset channel number directly For channel number 5 press 5 For channel number 15 press 10 then 5 For channel number 20 press 10 then 10 0 TUNING UP DOWN Tune into stations FM MODE Change the FM reception mode Sound control section Amplifier You can always perform the following operations SURROUND Turn on and select Surround modes DSP Turn on and select DSP modes SURR DSP OFF Turn off Surround and DSP modes After pressing SOUND you can perform the following operations FRONTeL then LEVEL Adjust the left front speaker output level FRONT R then LEVEL Adjust the right front speaker output level CENTER then LEVEL SURR L then LEVEL Adjust the center speaker output level Adjust the left surround speaker output level Adjust the right surround speaker output level Adjust the surround back speaker output level SUBWOOFER then LEVEL Adjust the subwoofer output level SURR R then LEVEL SURR BACK DIGITAL EQ then LEVEL Select the sound frequency bands and adjust its level TEST Turn on or off test tone output BASS B
86. G appears on the display The ANALOG indicator lights up SPEAKERS 1 voume IZ 21 20 effect fully useful at midnight MID NIGHT OFF Select when you want to enjoy surround with its full dynamic range no effect applied Notes e f Analog Direct is in use Midnight Mode is temporarily canceled e Midnight Mode is not valid for DVD MULTI playback mode When the input level of the analog source is too high the sounds will be distorted If this happens you need to attenuate the input signal level to prevent the sound distortion Once you have made adjustment it is memorized for each analog source Attenuating the Input Signal Jvc OL o Press and hold INPUT ATT INPUT ANALOG so that the INPUT ATT indicator lights up on the display Each time you press and hold the button the input attenuator mode turns ON or off NORMAL Note This function is not valid when DVD MULTI is selected or when Analog Direct is activated Turning Analog Direct On and Off You can enjoy the sound closer to the original source by overriding the sound adjustments such as speaker output level adjustments see page 32 Digital Equalization see page 32 Surround and DSP modes see pages 34 to 39 Bass Boost see page 22 and Midnight Mode see page 20 You can only adjus
87. I 21 4 Turn MULTI JOG to select an appropriate room size to match to your listening room The room size changes as follows To select your appropriate room size see Room size and the speaker distance on page 26 SPEAKERS 1 voume IZ 21 SMALL MID gt LARGE Back to the beginning LARGE is the initial setting 5 Press in MULTI JOG PUSH SET COMPLETE appears on the display then goes back to the source indication Speaker configuration settings now become active SPEAKERS 1 voume IZ Note This procedure will not be completed if you stop in the middle of the setting process 25 Speakers channels number and the size Basic Setting Items You can find how each of the speaker size is defined according to the number of connected speakers speaker channel CH number you select In the following tables L stands for left front speaker for right front speaker for center speaker LS for left On the following pages you can adjust the following items Items To do See page surround speaker RS for right surround speaker SB for SUB WOOFER Register your subwoofer 27 surround back speaker and SUBWFR for subwoofer Subwoofer is counted as 0 1 channel FRONT SPEAKER Register your front speaker size 27 CNTR SPEAKER Register your center speaker size 27 The size of
88. IT button 27 31 ADJUST button 31 ANALOG DIRECT button and lamp 21 Pur arr It 11 VOLUME Jl 11 VIRTUAL SB Surround Back indicator 34 35 ONE TOUCH OPERATION indicator 30 SLEEP indicator 22 MIDNIGHT MODE indicator 20 DIGITAL EQ equalization indicator 32 Speaker and signal indicators 18 Digital signal format indicators 20 Main Display 17 DSP indicator 19 38 3D PHONIC indicator 38 HEADPHONE indicator 19 38 SPEAKERS 1 2 indicators 19 INPUT ATT attenuator indicator 20 VOLUME level indicator 17 22 BASS BOOST indicator 22 Rear Panel RX 8030VBK DIGITAL IN COMPU LINK 4 S VIDEO CAUTION SPEAKER IMPEDANCE 8 Q 160 CAUTION SPEAKER IMPEDANCE Oe QD Q 850 150 Dao 160 320 Or RIGHT LEFT FRONT SPEAKERS SINGLE USE See Instruction Manual For Connection RIGHT LEFT RIGHT SURROUND BACK SPEAKERS maSURROUND SPEAKERS mmm SPEAKER RX 7O3O0VBK BRX 7032VSL N s El S VIDEO
89. JVC p AUDIO VIDEO CONTROL RECEIVER RX 8030VBK RX 7030VBK RX 7032VSL PARADII IIAN vV Y LIN Illi Remote lll 0 DIGITAL EX E lt For RX 8030VBK dts d co VENTER For RX 8030VBK INSTRUCTIONS For Customer Use Enter below the Model No and Serial No which are located either on the rear bottom or side of the cabinet Retain this information for future reference Model No Serial No LVT1007 001A J Warnings Cautions and Others Mises en garde precautions et indications diverses CAUTION RISK OF ELECTRIC SHOCK DONOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO
90. LLY INSERT ATTENTION POUR EVITER LES CHOCS ELECTRIQUES INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND G 2 Caution Proper Ventilation To avoid risk of electric shock and fire and to protect from dam age Locate the apparatus as follows Front No obstructions open spacing Sides No obstructions in 10 cm from the sides Top No obstructions in 10 cm from the top Back No obstructions in 15 cm from the back Bottom No obstructions place on the level surface In addition maintain the best possible air circulation as illus trated Attention Ventilation Correcte Pour viter les chocs lectriques l incendie et tout autre d gat Disposer l appareil en tenant compte des imp ratifs suivants Avant Rien ne doit g ner le d gagement Flancs Laisser 10 cm de d gagement lat ral Dessus Laisser 10 cm de d gagement sup rieur Arri re Laisser 15 cm de d gagement arri re Dessous Rienne doitobstruer par dessous poser l appareil sur une surface plate Veiller galement ace que l aircircule le mieux possible comme illustr Spacing 15 cm or more D gagement de 15 cm ou plus Wall or obstructions t Mur ou obstruction H RX 8030VBK RX 7030VBK Stand height 15 cm or more Hauteur du socle 15 cm ou plus Floor Plancher E Table of Contents Introduction eee nn e 2 Precautions era sav
91. NAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail purchase for the period as shown below The Warranty Period PARTS LABOR YRS 2 YRS THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY 50 UNITED STATES THE DISTRICT OF COLUMBIA AND IN COMMONWEALTH OF PUERTO RICO WHAT WE WILL DO If this product is found to be defective JVC will repair or replace defective parts at no charge to the original owner Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers Parts used for replacement are warranted only for the remainder of the Warranty Period All products and parts thereof may be brought to a JVC authorized service center on a carry in basis except for Television sets having a screen size 25 inches and above which are covered on an in home basis WHAT YOU MUST DO FOR WARRANTY SERVICE Return your product to a JVC authorized service center with a copy of your bill of sale For your nearest JVC authorized service center please call toll free 800 537 5722 If service is not available locally box the product carefully preferably in the original carton and ship insured with a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center the name and location of which will be given to you by the toll free number If you have any questions concerning yo
92. NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION To reduce the risk of electrical shocks fire etc 1 Do not remove screws covers or cabinet 2 Do not expose this appliance to rain or moisture ATTENTION Afin d viter tout risque d lectrocution d incendie etc 1 Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l appareil 2 Ne pas exposer l appareil la pluie ni l humidit Caution 0 1 STANDBY ON button Disconnect the mains plug to shut the power off completely The 0 1 STANDBY ON button in any position does not disconnect the mains line The power can be remote controlled Attention Commutateur STANDBY ON D connecter la fiche de secteur pour couper compl tement le courant Le commutateur 1 STANDBY ON ne coupe jamais compl tement la ligne de secteur quelle que soit sa position Le courant peut tre t l command For U S A This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If
93. OMPU LINK remote control system to operate the connected MD recorder IMPORTANT This receiver is equipped with the following video jacks composite video S video and component video jacks You can use any of the three to connect a video component However the video signals from one type of these input jacks are transmitted only through the video output jacks of the same type Therefore if a recording video component and a playing video component are connected to the receiver through the video jacks of different type you cannot record the picture In addition if the TV and a playing video component are connected to the receiver through the video jacks of different type you cannot view the playback picture on the TV RX 8030V ONLY Video camera To listen to the sound after connection press VIDEO The VIDEO input jacks on the front panel inside the front door are convenient when connecting and disconnecting the component frequently To audio output To composite video V output To S video output gt To optical digital output VIDEO IGITAL S VIDEO VIDEO L AUDIO R E OO Video camera When using the digital input terminal Select the digital input mode correctly For details see Selecting the Analog or Digital Input Mode on page 19 13 VCR s To listen to the sound after connection press VCR 1 or
94. OOST Turn on or off Bass Boost Note After adjusting sounds press the corresponding source selection button to operate your target source by using the 10 keys otherwise the 10 keys cannot be used for operating your target source CD player After pressing CD you can perform the following operations on a CD player Start playing aa Return to the beginning of the current or previous track gt gt Skip to the beginning of the next track Stop playing Pause playing To resume press gt 1 10 0 10 Select a track number directly For track number 5 press 5 For track number 15 press 10 then 5 For track number 20 press 10 then 10 0 For track number 30 press 10 10 then 10 0 CD changer For RX 8030VBK After selecting CDDSC by pressing CONTROL repeatedly you can perform the following operations on a CD changer For RX 7030VBK RX 7032VSL After pressing CD DISC you can perform the following operations on a CD changer gt Start playing lt Return to the beginning of the current or previous track gt gt Skip to the beginning of the next track Stop playing or recording Pause playing To resume press gt 1 6 7 P Select the number of a disc installed in a CD changer After pressing CD you can perform the following operations on a CD changer 1 10 0 10 Select a track number directly For track number 5 press 5 For track numbe
95. Outdoor FM Antenna Cable not supplied FM 750 COAXIAL A Using the Supplied FM Antenna The FM antenna provided can be connected to the FM 75 Q COAXIAL terminal as temporary measure B Using the Standard Type Connector Not Supplied A standard type connector should be connected to the FM 75 COAXIAL terminal Note If reception is poor connect the outdoor FM antenna not supplied Before attaching a 75 Q coaxial cable with a connector the kind with a round wire going to an outdoor antenna disconnect the supplied FM antenna AM Antenna Connections Turn the loop until you have the best reception ANTENNA AM Loop Antenna supplied Snap the tabs on the loop into the slots of the base to assemble the AM loop FM 750 COAXIAL Outdoor single vinyl covered wire not supplied Notes f the AM loop antenna wire is covered with vinyl remove 7 the vinyl by twisting it as illustrated Make sure the antenna conductors do not touch any other terminals connecting cords and power cord This could cause poor reception f reception is poor connect an outdoor single vinyl covered wire not supplied to the AM EXT terminal Keep the AM loop antenna connected Connecting the Speakers You can connect the following speakers Two pairs of front speakers to produce normal stereo sound One pair of surround speaker
96. PTICAL Select the components connected to 3 0 m 10 ft digital optical terminals 20 3 0 m 10 ft VIDEO IN DVD Select the type of video terminal Distance used for the DVD player 30 2 7 m 9 ft VIDEO IN DBS Select the type of video terminal 27m 9ft used for the DBS tuner 30 24m 8 ft ONETOUCH OPE Store the volume level for each 21m 7 ft Source 30 2 1 m 7 ft 1 8 m 6 ft Notes Distance These items can be set using Quick Speaker Setup This setting is only for RX 8030VBK 2 4 m 8 ft For RX 7030VBK RX 7032VSL it is automatically set according to 2 4 m 8 ft your DGTL IN COAX setting 2 1 m 7 ft 1 5 m 5 ft 1 5 m 5 ft 1 2 m 4 ft 26 Basic Procedure JVE c Ly c 22 550000 a9 C c S Before you start remember There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again Ex When setting One Touch Operation to ON 1 Press SETTING The last selected item appears on the display SPEAKERS 1 voume 21 2 Turn MULTI JOG until item you want appears on the display In this example select ONE TOUCH OPE For available items see the list Basic Setting Items on page 26 SPEAKERS 1 voume 21 3 Push in MULTI JOG PUSH SET The current setting for the selec
97. Patterns Adjusting the Speaker Output Levels Adjusting the Sound Parameters for the Surround and DSP modes sess 33 Using the Surround Modes 34 Reproducing Theater Ambience eee 34 Introducing the Surround Modes sss 34 Surround Modes Applicable to the Various Software 36 Activating the Surround Modes sss 37 Activating the EX ES setting esee 37 Bi Activating the Surroung modes see 37 Using the DSP Modes 38 Reproducing the Sound Field 5 enne 38 Introducing the DSP Modes eee 38 Activa ng th DSP 39 Using the DVD MULTI Playback Mode 40 Activating the DVD MULTI Playback Mode 40 COMPU LINK Remote Control System 41 AV COMPU LINK Remote Control System 42 Operating JVC s Audio Video Components 44 Operating Audio Components sese 44 Operating Video Components esee 46 Operating Other Manufacturers Video Equipment iaa 47 Troubleshooting eese 50 51 P SOOV Features with this mark are provided only for RX 8030VBK RX 7030V 4 ONLY Fe
98. Press SLEEP once The remaining time until the shut off time appears in minutes To change the shut off time press SLEEP repeatedly To cancel the Sleep Timer Press SLEEP repeatedly until SLEEP Omin appears on the display The SLEEP indicator goes off Turning off the power also cancels the Sleep Timer Recording a source For analog to analog recording You can record any analog playback source onto the recording components connected to the audio output jacks on the rear of this unit at the same time For digital to digital recording You can record the currently selected digital input source through the receiver to a digital recording device connected to the DIGITAL OUT terminal Notes Analog to digital and digital to analog recordings are not possible The output volume level Midnight Mode see page 20 Bass Boost see the left column Digital Equalization see page 32 Surround modes and DSP modes see pages 34 to 39 cannot affect the recording Basic adjustment auto memory This receiver memorizes sound settings for each source when you turn off the power when you change the source and when you assign the source name see page 21 When you change the source the memorized settings for the newly selected source are automatically recalled The following can be stored for each source Analog digital input mode see pages 19 and 20 nput attenuator mode see page 20
99. R 1 Press TAPE CDR Make sure TAPE appears on the display 2 Press and hold TAPE CDR until ASSGN CDR appears on the display To change the source name to TV and TAPE repeat the same procedure above Note Without changing the source name you can still use the connectedcomponents However there may be some inconvenience For RX 8030VBK TAPE or TV will appear on the display when you select the MD recorder or DBS tuner You cannot use the digital input see pages 19 and 20 for the MD recorder You cannot use the COMPU LINK remote control system see pages 41 to operate the MD recorder For RX 7030VBK TAPE or TV will appear on the display when you select the CD recorder or DBS tuner You cannot use the digital input see pages 19 and 20 for the CD recorder 21 The following basic operations are possible only using the remote control Reinforcing the Bass Muting the Sound Using the Sleep sj Changing Timer the Display Brightness Reinforcing the Bass You can boost the bass level Once you have made adjustment it is memorized for each source 1 Press SOUND The 10 Keys are activated for sound adjustments Pm Press BASS BOOST to turn on Bass Boost The BASS BOOST indicator lights up e Each time you press the button Bass Boost turns on BOOST ON and off BOOST OFF alternately RX 7030V ONLY E
100. ROUND Surround modes change as follows DOPROLOGICI MOVIE PL II MUSIC PRO Send NEO 6MUSIC NEO 6CINMA For Dual Mono software you can select the channel you listen to See page 29 To adjust the speaker output level see pages 32 and 33 To cancel the Surround mode Press SURROUND DSP OFF or SURR DSP OFF on the remote control SURR OFF appears on the display 37 ll Using the DSP Modes This unit activates a variety of DSP modes automatically The basic settings and adjustments stored see pages 25 to 33 are applied automatically Reproducing the Sound Field The sound heard in a concert hall club etc consists of direct sound and indirect sound early reflections and reflections from behind Direct sounds reach the listener directly without any reflection On the other hand indirect sounds are delayed by the distances of the ceiling and walls These direct sounds and indirect sounds are the most important elements of the acoustic surround effects The DSP modes can create these important elements and give you a real being there feeling Reflections from behind Early reflections Introducing the DSP Modes The DSP modes include the following modes DAP Digital Acoustic Processor modes HALL 1 HALL 2 LIVE CLUB DANCE CLUB PAVILION THEATER 1 THEATER 2 ALL CH STEREO MONO FILM 3D HEADPHONE Mode
101. S NONE Not available DTS DTS 1 0 3 0 2SPK 1SPK NONE Not available DTS DTS Dual Mono 2SPK 1SPK NONE Not available DUAL MONO Incoming Signal Type Available Surround Mode Analog PCM Dolby Digital 2 0 DTS 2 0 PL II MOVIE PL II MUSIC PRO LOGIC NEO 6 CINMA NEO 6 MUSIC DVD MULTI None 3D HEADPHONE Mode 3D H PHONE You can also enjoy the Surround modes through the headphones If you press SURROUND when the front speakers 1 and 2 are both deactivated 3D HEADPHONE mode 3D H PHONE is activated without respect to the type of software played back 3D H PHONE appears on the display and the DSP and HEADPHONE indicators also light up Virtual 6 1 channel surround If you have connected and activated the surround speakers you can use Virtual 6 1 channel surround when playing back Dolby Digital EX or DTS ES software without connecting the surround back speakers This surround reallocates the surround back channel to the surround speakers so that you can still feel the great surround effect from behind The VIRTUAL SB Surround Back indicator lights up on the display 36 Activating the Surround Modes Activating the Surround Modes Available Surround modes vary depending on the speaker settings and the incoming signals See page 36 Activating one of the Surround modes for a source automatically recalls the memorized settings and adjustments see pages 25 to 33 You can also use the buttons on th
102. S video DVD IN VCR 1 IN VCR 2 IN TV SOUND DBS IN VIDEO Y luminance 1 V p p 75 Q C chrominance burst 0 286 V p p 75 Q Component video DVD IN DBS IN Y luminance 1 V p p 75 Q 0 7 V p p 75 Video Output Level Composite video VCR 1 OUT VCR 2 OUT MONITOR OUT 1 V p p 75 Q S video VCR 1 OUT VCR 2 OUT MONITOR OUT Y luminance 1 V p p 75 Q C chrominance burst 0 286 V p p 75 Q Component video MONITOR OUT Y luminance 1 V p p 75 Q 0 7 V p p 75 Q Synchronization Negative Signal to Noise Ratio 45 dB FM tuner IHF Tuning Range Usable Sensitivity Monaural 50 dB Quieting Sensitivity Monaural Stereo Stereo Separation at REC OUT 87 5 MHz to 108 0 MHz 12 8 dBf 1 2 uV 75 16 0 dBf 1 7 pV 75 Q 37 5 dBf 20 5 uV 75 35 dB at 1 kHz AM tuner Tuning Range 530 kHz to 1 710 kHz General AC 120V 60 Hz 320 W 440 VA at operation 2 W in standby mode 435 mm x 157 mm x 425 mm 17 he in x 6 Aic in x 16 3 4 in 12 2 kg 27 0 Ibs Power Requirements Power Consumption Dimensions W x H x D Mass Designs amp specifications are subject to change without notice 51 RX 7030VBK RX 7032VSL Amplifier Output Power At Stereo operation Front ch 110 W per channel min RMS driven into 8 Q 20 Hz to 20 kHz with no more than 0 08 total harmonic distortion At Surround operation Front ch 110 W per channel m
103. TV converter or DBS tuner After pressing CATV DBS CONTROL you can perform the following operations on a CATV converter or DBS tuner CH Change the channels 1 10 0 0 100 10 Select the channels The 10 0 button will function as the ENTER button if your equipment requires pressing ENTER after selecting a channel number Try to operate your CATV converter or DBS tuner by pressing CATV DBS coi When your CATV converter or DBS tuner turns on or off you have entered the correct code If there are more than one code listed for your brand of CATV converter or DBS tuner try each one until the correct one is entered Note You cannot preset the signals for both the CATV converter and DBS tuner at the same time 47 To change the transmittable signals for operating another manufacturer s VCR 1 Press and hold VCR 1 for RX 8030VBK or VCR for RX 7030VBK 2 Press VCR 1 for RX 8030VBK or VCR for RX 7030VBK For RX 8030VBK CALL appears on the display window of the remote control 3 Enter manufacturer s code using buttons 1 9 and 0 See the list on page 49 to find the code 4 Release VCR 1 O lor VCR o The following buttons can be used for operating a VCR VCR 1 OVI For RX 8030VBK Turn on and off a VCR VCR OM For RX 7030VBK Turn on and off a VCR After pressing VCR 1 or VCR you can perform the following operations on a VCR CH Change the TV channels on a
104. V COMPU LINK remote control system see page 42 connect the DVD player also as described in Analog Connections see page 15 16 Digital output terminal You can connect any digital components which have an optical digital input terminal Digital optical cable not supplied between digital optical terminals When the digital recording equipment such as an MD recorder and CD recorder has a digital optical input terminal connecting it to the DIGITAL OUT terminal enables you to perform digital to digital recording PCM DOLBY DIGITAL DTS DIGITAL OUT Note The digital signal format transmitted through the DIGITAL OUT terminal is the same as that of the input signal This means that when the DTS Digital Surround signals are input the DTS Digital Surround signals are transmitted Connecting the Power Cord Before plugging the receiver into an AC outlet make sure that all connections have been made Plug the power cord into an AC outlet Keep the power cord away from the connecting cables and the antenna The power cord may cause noise or screen interference Note The preset settings such as preset channels and sound adjustment may be erased in a few days in the following cases When you unplug the power cord When a power failure occurs CAUTIONS Do not touch the power cord with wet hands Do not pull on the power cord to unpl
105. VCR 1 10 0 0 100 10 Select the TV channels The 10 0 button will function as the ENTER button if your VCR requires pressing ENTER after selecting a channel number gt Start playback REW Rewind a tape Fast wind a tape Stop playing or recording Pause playing resume press gt REC PAUSE Enter recording pause by pressing this button To start recording again press this button then 5 Try to operate your VCR by pressing VCR 1 cl or VCR When your VCR turns on or off you have entered the correct code If there are more than one code listed for your brand of VCR try each one until the correct one is entered 48 To change the transmittable signals for operating another manufacturer s DVD player 1 Press and hold AUDIO 2 Press DVD For RX 8030VBK CALL appears on the display window of the remote control 3 Enter a manufacturer s code using buttons 1 9 and 0 See the list on page 49 to find the code 4 Release AUDIO After pressing DVD or DVD MULTI you can perform the following operations on a DVD player gt Start playing lt Return to the beginning of the current or previous chapter gt gt Skip to the beginning of the next chapter Stop playing I Pause playing To resume press After pressing DVD or DVD MULTI these buttons can be used for the DVD 2 a 3 menu operations Note CO Go For deta
106. You can connect either an MD recorder or a cassette deck to the TAPE MD jacks When connecting a cassette deck see page 12 RX 8030VBK MD recorder To audio output Qui 8 e a c LD Note When connecting an MD recorder to the TAPE MD jacks change the source name to MD which will be shown on the display when it is selected as the source See page 21 for details Video component connections Use the cables with RCA pin plugs not supplied Connect the white plug to the audio left jack the red plug to the audio right jack and the yellow plug to the video jack If your video components have S video Y C separation and or component video Y Pr terminals connect them using an S video cable not supplied and or component video cable not supplied By using these jacks you can get better picture quality in the order Component video gt S video gt Composite video If your video components have an AV COMPULINK jack See also page 42 for detailed information about the connection and the AV COMPU LINK remote control system For RX 7030VBK You can connect an MD recorder to the TAPE CDR jacks if they are not used for connecting another component such as a cassette deck or CD recorder When connecting an MD recorder to the TAPE CDR jacks see page 12 Though your MD recorder is one of JVC products with the COMPU LINK remote control system you cannot use the C
107. ack number 15 press 10 then 5 For track number 20 press 10 then 10 0 For track number 30 press 10 10 then 10 0 Enter recording pause by pressing this button To start recording again press this button then REC PAUSE Cassette deck For RX 8030VBK After pressing TAPE MD or selecting TAPE by pressing CONTROL repeatedly you can perform the following operations on a cassette deck For RX 7030VBK After pressing TAPE CDR or TAPE CDR CONTROL you can perform the following operations on a cassette deck gt Start playing REW Fast wind the tape from right to left EE Fast wind the tape from left to right Stop playing or recording Pause playing To resume press REC PAUSE Enter recording pause by pressing this button To start recording again press this button then MD recorder ERA After pressing TAPE MD or selecting by pressing CONTROL repeatedly you can perform the following operations on a MD recorder gt Start playing lt Return to the beginning of the current or previous track gt gt Skip to the beginning of the next track Stop playing or recording Pause playing To resume press REC PAUSE Enter recording pause by pressing this button To start recording again press this button then Selecting TAPE will allow you to control the MD recorder Note You can use either source sel
108. ack to the beginning When connecting an MD recorder to the digital input terminal change the source name to MD from TAPE see page 21 f you have changed the source name from TV to DBS DBS appears see page 21 29 For RX 7030VBK RX 7032VSL As you set the components connected to the digital coaxial terminal DIGITAL IN 1 the optical terminals DIGITAL IN 2 4 will be automatically fixed to connect the components listed below Memorizing the Volume Level for Each Source This unit memorizes some settings separately for each source In addition you can store the volume level for each source with the other memorized settings One Touch Operation m One Touch Operation ONE TOUCH OPE When DIGITAL IN 1 DGTL IN COAX is set to DVD 2I 3 TV or DBS 4 CDR When DIGITAL IN 1 DGTL IN COAX is set to CD 2 DVD 3 TV or DBS 4 CDR When DIGITAL IN 1 DGTL IN COAX is set to TV or DBS 2 DVD 3 CD 4 CDR When DIGITAL IN 1 DGTL IN COAX is set to CDR 2 DVD 3 CD 4 TV or DBS If you have changed the source name from TV to DBS DBS appears see page 21 Setting the Component Video Input When you use the component video inputs for connecting the DVD player and or DBS tuner register the type of input jacks If you have not selected appropriate video input jacks the
109. al input terminal setting should be correctly done for the sources you want to select the digital input mode see Setting the Digital Input Terminals on pages 29 and 30 1 Press one of the source selection buttons for which you want to change the input mode For RX 8030VBK DVD VIDEO TV SOUND DBS CD CDR or TAPE MD For RX 7030VBK DVD TV SOUND DBS CD or TAPE CDR If TAPE is selected as the source digital input mode is not available To change the source name see Changing the Source Name on page 21 Continued on the next page 19 2 Press INPUT DIGITAL or ANALOG DIGITAL INPUT on the remote control to select AUTO The DIGITAL AUTO indicator lights up on the display DIGITAL AUTO R LFE DO DIGITAL SPEAKERS 1 RS a voume I 21 When selecting DGTL AUTO the following indicators indicate the digital signal format of the incoming signal Lights up when Linear PCM signals come in Lights up when Dolby Digital signals Setting the Dynamic Range You can enjoy a powerful sound at night using the Midnight Mode j lL Ld Press MIDNIGHT MODE so that MID NIGHT 1 or MID NIGHT 2 appears on the display The MIDNIGHT MODE indicator also lights up come in dts L
110. and activated speakers If incoming signals change from 2 channel digital signal to another digital signal type MONO FILM is canceled and an appropriate Surround mode is activated Activating the DSP Modes Activating one of the DSP modes for a source automatically recalls the memorized settings and adjustments see pages 25 to 33 You can also use the buttons on the remote control for the same functions oo 000000 o o e a 1 Select and play any sound source 2 Press DSP repeatedly until the DSP mode you want appears on the display Each time you press the button the DSP modes change as follows DIGITAL AUTO Dopiarat gt HALL 1 gt HALL 2 LIVE CLUB DANCE CLUB PAVILION ALL STEREO THEATER 1 THEATER2 MONO FILM Back to the beginning When surround speakers are set to NONE you cannot select ALL STEREO When multi channel signals come in you cannot select MONO FILM Note When the surround speakers are deactivated the 3D PHONIC processing is applied to the DSP modes the 3D PHONIC indicator also lights up To cancel the DSP modes Press SURROUND DSP OFF or SURR DSP OFF on the remote control SURR OFF appears on the display When the front speakers are deactivated HEADPHONE will appea
111. annel output levels see page 32 Surround and DSP mode selection see pages 37 and 39 Bass Boost setting see the left column Notes e f the source is FM or AM you can assign a different setting for each band e f you want to memorize the volume level with the above settings set One Touch Operation to ON see page 30 RI Receiving Radio Broadcasts You can browse through all the stations or use the preset function to go immediately to a particular station Tuning in to Stations Manually Using Preset Tuning Qo0 ll Q 00 od Lo 1 Press FM or AM to select the band The last received station of the selected band is tuned in TUNED STEREO SPEAKERS 1 voume I 2 Press FM AM TUNING A or V repeatedly until you find the frequency you want Pressing FM AM TUNING A increases the frequency Pressing FM AM TUNING decreases the frequency TUNED STEREO SPEAKERS 1 voume I Notes e When a station of sufficient signal strength is tuned in the TUNED indicator lights up on the display When an FM stereo program is received the STEREO indicator also lights up When you hold and then release the button in step 2 the frequency keeps changing until a station is tuned in From the remote control 1 Press FM AM Each time you p
112. at the SPEAKERS 2 indicator is not lit on the display To use the speakers connected to the FRONT SPEAKERS 2 terminals press SPEAKERS ON OFF 2 so that SPEAKERS 2 indicator lights up on the display Make sure that the SPEAKERS 1 indicator is not lit on the display To use both sets of the speakers press SPEAKERS ON OFF 1 and SPEAKERS ON OFF 2 so that the SPEAKERS 1 2 indicators light up on the display To use neither sets of the speakers press SPEAKERS ON OFF 1 and SPEAKERS ON OFF 2 so that the SPEAKERS 1 2 indicators go off from the display The HEADPHONE indicator lights up and HEADPHONE appears on the display Activating the speakers turns on the Surround and DSP modes previously selected Listening with headphones only Deactivate both sets of the front speakers and connect headphones to the PHONES jack You can enjoy the sound effects through the headphones when Surround or DSP mode is activated 3D HEADPHONE 3D H PHONE mode 3D H PHONE appears on the display and the DSP and HEADPHONE indicator lights up on the display For details see page 36 Note When you select DVD MULTI as the source or any one of the Surround DSP mode which activates the center and or surround speaker s you can use only one set of the speakers CAUTION Be sure to turn down the volume Before connecting or putting on headphones as its high volume can damage both the headphones and your hearing Befor
113. atures with this mark are provided only for Q RX 7030VBK B Introduction We would like to thank you for purchasing one of our JVC products Before operating this unit read this manual carefully and thoroughly to obtain the best possible performance from your unit and retain this manual for future reference CC Compensative Compression converter ONLY for RX 8030VBK CC Converter eliminates jitter and ripples achieving a drastic reduction in digital distortion by processing the digital music data in 24 bit quantization and by expanding the sampling frequency to 128 kHz for fs 32 kHz signals 176 4 kHz for fs 44 1 kHz signals 192 kHz for fs 48 kHz signals By using the CC Converter you can obtain a natural sound field from any source See page 21 for details K2 technology ONLY for RX 8030VBK K2 technology has been designed to enable natural audio reproduction achieving a drastic reduction in digital distortion and creating original sound ambience with high precision Compatible with various audio formats including DTS 96 24 RX 8030VBK and RX 7030VBK allow you to enjoy a newly introduced audio format such as Dolby Digital EX Dolby Pro Logic II DTS ES DTS Neo 6 and DTS 96 24 This unit is also compatible with Dual Mono signals recorded in Dolby Digital and DTS discs DAP Digital Acoustic Processor Sound field simulation technology allows precise ambience recreation
114. ayer to the component video input jacks make the component video input setting correctly for AV COMPU LINK See page 30 for details To component video output To subwoofer output To center channel audio output To S video output To composite video output To left right front channel audio output To left right surround channel audio output gt Note When connecting a DVD player to the component video input jacks make the component video input setting correctly for AV COMPU LINK See page 30 for details 15 lll Digital Connections This receiver is equipped with four DIGITAL IN terminals one digital coaxial terminal and three digital optical terminals and one DIGITAL OUT optical terminal on the rear For RX 8030VBK Another digital optical input terminal is located on the front panel see page 13 IMPORTANT When connecting a DVD player digital TV broadcast tuner or DBS tuner using the digital terminals you also need to connect it to the video jacks on the rear Without connecting it to the video jacks you can view no playback picture After connecting the components using the DIGITAL IN terminals set the following correctly if necessary Set the digital input DIGITAL IN terminal setting correctly For details see Setting the Digital Input Terminals on page 29 Select the digital input mode correctly For details
115. change without notice If they Zenith 27 28 are changed this remote control cannot operate the equipment 49 Troubleshooting Use this chart to help you solve daily operational problems If there is any problem you cannot solve contact your JVC s service center PROBLEM The display does not light up POSSIBLE CAUSE The power cord is not plugged in SOLUTION Plug the power cord into an AC outlet No sound from speakers Speaker signal cables are not connected Check speaker wiring and reconnect if necessary See pages 9 to 11 The SPEAKERS ON OFF 1 and SPEAKERS ON OFF 2 buttons are not set correctly Press SPEAKERS ON OFF 1 and SPEAKERS ON OFF 2 correctly See page 19 An incorrect source is selected Select the correct source Muting is activated Press MUTING to cancel the mute See page 22 An incorrect input mode analog or digital is selected Select the correct input mode analog or digital See page 19 Sound from one speaker only Speaker signal cables are not connected properly Check speaker wiring and reconnect if necessary See pages 9 to 11 Continuous hiss or buzzing during FM reception Incoming signal is too weak Connect an outdoor FM antenna or contact your dealer See page 8 The station is too far away Select a new station An incorrect antenna is used Check with your dealer to be sure you have the co
116. channel to the surround speakers so that you can still feel the great surround effect from behind The VIRTUAL SB Surround Back indicator lights up on the display DTS 96 24 In recent years there has been increasing interest in higher sampling rates both for recording and for reproducing at home Higher sampling rates allow wider frequency range and greater bit depths provide extended dynamic range DTS 96 24 is a multi channel digital signal format fs 96 kHz 24 bits introduced by Digital Theater Systems Inc to deliver better than CD sound quality into the home When DTS 96 24 signal is detected the 96 24 indicator lights up You can enjoy its 5 1 channel sound with full quality DTS Neo 6 DTS Neo 6 is another conversion method to create 6 channel plus subwoofer from analog digital 2 channel software by using the high precision digital matrix decoder used for DTS ES Matrix 6 1ch When one of Neo 6 modes is activated the NEO 6 indicator lights up on the display This receiver provides the following DTS NEO 6 modes Neo 6 Cinema NEO 6CINMA and Neo 6 Music NEO 6MUSIC NEO 6CINMA Suitable for playing movies You can get the same atmosphere with 2 channel software as with 6 1 channel software It is also effective for playing software encoded with conventional surround formats NEO 6MUSIC Suitable for playing music software The front channel signals bypass the decoder resulting in no l
117. ck without setting other switches manually The receiver automatically turns on and changes the source to VCR 1 for RX 8030VBK or VCR for RX 7030VBK RX 7032VSL The TV automatically turns on and changes the input mode to the appropriate position so that you can view the playback picture When you insert a video cassette with its safety tab press the play gt button on the VCR or on the remote control So you can get the same result One Touch DVD Play Simply by starting playback on the DVD player you can enjoy the DVD playback without setting other switches manually When the DVD player is connected through the analog input jacks on this receiver and analog input is selected the receiver automatically turns on and changes the source to DVD or DVD MULTI When the DVD player is connected through the digital input terminal on this receiver and digital input is selected the receiver automatically turns on and changes the source to DVD The TV automatically turns on and changes the input mode to the appropriate position so that you can view the playback picture Automatic Selection of TV s Input Mode When you select as the source to play on the receiver the TV automatically changes the input mode to the TV tuner so that you can watch TV When you select any other video source other than TV as the source to play on the receiver the TV automatically changes the input
118. d the red plug to RX 8030VBK the audio right jack Left front speaker Right front speaker If your audio components have a COMPU LINK jack See also page 41 for detailed information about the connection and the COMPU LINK remote control system CAUTION If you connect a sound enhancing device such as a graphic equalizer between the source components and this receiver the sound output through this receiver may be distorted RX 8030v ONLY Turntable Mum Power amplifier To listen to the sound after connection press PHONO RX 8030VBK MO fe Turntable If a ground cable is provided for your turntable connect the cable to the _ screw marked 5 on the rear Power amplifier To audio output Right surround speaker Left surround speaker Note This connection is for the turntable with an MM moving magnet type cartridge Any turntables incorporating a small output cartridge such as an MC moving coil type must be connected to this receiver through a commercial head amplifier or step up transformer Direct connection may result in insufficient volume Surround back speakers Left Right Note If you connect one surround back speaker connect the surround back speaker to the left surround back PREOUT jack SURR BACK L 11 CD player CD recorder To listen to the sound after connection press CD To listen to the sound af
119. dance Composite video DVD IN VCR IN TV SOUND DBS IN 1 V p p 75 Q S video DVD IN VCR IN TV SOUND DBS IN Y luminance C chrominance burst Component video DVD IN DBS IN Y luminance 1 V p p 75 Q 0 286 V p p 75 1 V p p 75 0 7 V p p 75 Q Video Output Level Composite video VCR OUT MONITOR OUT S video VCR OUT MONITOR OUT Y luminance C chrominance burst Component video MONITOR OUT Y luminance 1 V p p 75 Q 1 V p p 75 Q 0 286 V p p 75 Q 1 V p p 75 Q 0 7 V p p 75 Q Synchronization Negative Signal to Noise Ratio 45 dB FM tuner IHF Tuning Range Usable Sensitivity Monaural 50 dB Quieting Sensitivity Monaural Stereo Stereo Separation at REC OUT 87 5 MHz to 108 0 MHz 12 8 dBf 1 2 uV 75 Q 16 0 dBf 1 7 uV 75 Q 37 5 dBf 20 5 uV 75 Q 35 dB at 1 kHz AM tuner Tuning Range 530 kHz to 1 710 kHz General AC 120V 60 Hz 320 W 440 VA at operation 2 W in standby mode 435 mm x 157 mm x 425 mm 17 5e in x 6 7 16 in x 16 3 4 in 12 1 kg 26 7 Ibs Power Requirements Power Consumption Dimensions W x H x D Mass Designs amp specifications are subject to change without notice LEAKALARA EEA SEA AAEA REAR LEER REN RAN ORAS een INERCGIGAUROAGNINUA e JVC LIMITED WARRANTY AUDIO 2 JVC COMPANY OF AMERICA warrants this product and all parts thereof except as set forth below ONLY TO THE ORIGI
120. dow then press 4 2 Press CD then press 10 2 For RX 7030VBK 1 Press CD DISC then press 4 2 Press CD then press 10 2 If your CD changer is of 200 disc loading capability except for XL MC100 and XL MC301 you can do the following operations using the 10 keys after pressing CD 1 Select a disc number 2 Then select a track number always enter two digits 3 Start playback Examples Selecting disc number 3 track number 2 and starting playback Press 3 then 0 2 then gt Selecting disc number 10 track number 5 and starting playback Press 1 0 then 0 5 then gt Selecting disc number 105 track number 12 and starting playback Press 1 0 5 then 1 2 then gt Turntable RX 5030V After pressing PHONO you can perform the Num following operations on a turntable Start playing Stop playing CD recorder For RX 8030VBK After pressing CDR or selecting CDR by pressing CONTROL repeatedly you can perform the following operations on a CD recorder For RX 7030VBK After pressing TAPE CDR or TAPE CDR CONTROL you can perform the following operations on a CD recorder gt Start playing aa Return to the beginning of the current or previous track gt gt Skip to the beginning of the next track Stop playing or recording Pause playing To resume press 1 10 0 10 Select a track number directly For track number 5 press 5 For tr
121. e Virtual 6 1 channel surround when playing back DTS ES software without connecting the surround back speakers This surround reallocates the surround back channel to the surround speakers so that you can still feel the great surround effect from behind The VIRTUAL SB Surround Back indicator lights up on the display DTS 96 24 In recent years there has been increasing interest in higher sampling rates both for recording and for reproducing at home Higher sampling rates allow wider frequency range and greater bit depths provide extended dynamic range DTS 96 24 is a multi channel digital signal format fs 96 kHz 24 bits introduced by Digital Theater Systems Inc to deliver better than CD sound quality into the home When DTS 96 24 signal is detected the 96 24 indicator lights up You can enjoy its 5 1 channel sound with full quality DTS Neo 6 DTS Neo 6 is another conversion method to create 6 channel plus subwoofer from analog digital 2 channel software by using the high precision digital matrix decoder used for DTS ES Matrix 6 1ch When one of Neo 6 modes is activated the NEO 6 indicator lights up on the display This receiver provides the following DTS NEO 6 modes Neo 6 Cinema NEO 6CINMA and Neo 6 Music NEO 6MUSIC NEO 6CINMA Suitable for playing movies You can get the same atmosphere with 2 channel software as with 6 1 channel software It is also effective for playing software encoded with c
122. e control Operating Audio Components IMPORTANT To operate JVC s audio components using the supplied remote control You need to connect JVC s audio components through the COMPU LINK SYNCHRO jacks see page 41 in addition to the connections using cables with RCA pin plugs see pages 11 to 13 Aim the remote control directly at the remote sensor on the receiver If you use the buttons on the front panel to choose a source the remote control will not operate that source To operate a source with the remote control the source must be selected using source selection buttons on the remote control To operate the target component using the COMPU LINK remote control system set the source name correctly if required See page 21 Refer also to the manuals supplied with your components For RX 8030VBK RX 8030V When you press one of the source selection buttons the remote operation mode appears on the display window for about two hours Buttons Indications FM AM TUNER CD CD CDR CDR PHONO PHONO TAPE MD TAPE CONTROL repeatedly YOY o TAPE CDDSC_ lt _ CDR lt SOUND SOUND By pressing CONTROL repeatedly you can select VCR 1 TAPE or CDDSC as the source When you press one of the following buttons the remote operation mode appears on the display window for about two hours Buttons Indications FRONT L
123. e ox agde daran to ESPERE CERES 2 Parts Identification eee 3 Remote Control 5 2 3 Front Panel re oar exe iren 4 Icdvulme p 6 Getting 8 Before Installation J P eee 8 Checking the Supplied Accessories sess 8 Putting Batteries in the Remote Control 8 Connecting the FM and AM Antennas sees 8 Corinecting th Speakers as peter tr renes 9 Connecting Audio Video 11 B Analog Connections uei eerte 11 B Digital Conn ctolis 12 nee oce eee tete eei o Een 16 Connecting the Power Cord 16 Basic Operations 17 Daily Operational Procedure see 17 Turning On the eite Selecting the Source to Play Adjusting the Volume Selecting the Front Speakers Activating and Adjusting the Subwoofer Sound 19 Selecting the Analog or Digital Input Mode 19 Setting the Dynamic Range erento 20 Attenuating the Input Signal eee 20 Turning Analog Direct On and Off sss 21 Making Sounds N t tal 5 rines 21 Changing the Source Name 21 Reinforcing
124. e remote control for the same functions lll Activating the EX ES setting For multi channel digital software you can activate the EX ES 7 1 channel reproduction mode Once you have set EX ES 7 1 channel reproduction mode it is stored in memory and will be called up whenever you activate the Surround mode which the memorized EX ES 7 1 channel reproduction mode can be applied to 000 8 Press to select an appropriate setting for your enjoyment The currently selected EX ES 7 1 channel reproduction mode appears on the display Each time you press the button it changes as follows EX ES AUTO According to the incoming signal an appropriate Surround mode is applied For Dolby Digital EX and DTS ES EX ES 7 1 channel reproduction is applied For 5 1 channel or less encoded software 5 1 channel reproduction is applied EX ES ON Select to apply EX ES 7 1 channel reproduction to both 5 1 channel and 6 1 channel encoded software EX ES OFF Select to cancel the EX ES 7 1 channel reproduction f the surround back speakers are not connected or deactivated Virtual 6 1 channel surround is applied Notes When Surround mode is deactivated pressing EX ES will activate an appropriate Surround mode for the current source When an analog or digital 2 channel source is playin
125. e table below shows the relation of the Surround modes and the incoming signals with the surround back speakers and EX ES setting The numbers inside the parentheses following the incoming signal type indicate the number of the front channels and that of the surround channels For example 3 2 indicates that the signals are encoded with three front signals left right center and two stereo surround signals Incoming Signal Type Surround Back Channel Setting EX ES Setting Available Surround Mode Dolby Digital EX 2SPK 1SPK AUTO ON DOLBY D EX OFF DOLBY D NONE AUTO ON DOLBY D VIRTUAL SB OFF DOLBY D Dolby Digital 3 2 2 2 2SPKASPK AUTO DOLBY D ON DOLBY D EX OFF DOLBY D NONE Not available DOLBY D Dolby Digital 3 1 2 1 2SPK 1SPK AUTO ON OFF DOLBY D NONE Not available DOLBY D Dolby Digital 1 0 3 0 2SPK 1SPK NONE Not available DOLBY D Dolby Digital Dual Mono 2SPK 1SPK NONE Not available DUAL MONO DTS ES Discrete 6 1ch 2SPK 1SPK AUTO ON ES DSCRETE OFF DTS NONE AUTO ON DTS VIRTUAL SB DTS ES Matrix 6 1ch 2SPK 1SPK AUTO ON ES MATRIX DTS ES 96 24 Matrix OFF DTS NONE AUTO ON DTS VIRTUAL SB OFF DTS DTS DTS 96 24 3 2 2 2 2SPK 1SPK AUTO DTS 2 DTS 96 24 processing is not ON DTS NEO 6 2 applied If you want to apply the processing set the EX ES OFF DTS setting to OFF NONE Not available DTS DTS 3 1 2 1 2SPK 1SPK AUTO ON OFF DT
126. e to get out Others Should any metallic object or liquid fall onto the unit unplug the unit and consult your dealer before operating any further Do not expose this apparatus to rain moisture dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus Do not disassemble the unit since there are no user serviceable parts inside If anything goes wrong unplug the AC power cord and consult your JVC dealer 1 Parts Identification Remote Control RX 8030VBK AN CONTROL RECEIVER Iz I lat Waist at 2 7 Con COD Gi Gi DVD MULTI DVD CD FM AM Sees 3 VCR2 TVDBS VIDEO PHONO ANLOGDGITAL GC GD CD re 13 SURROUND DSP SURR DSP ANALOG 5 Cor ere 4 4 EXES BASSBOOST FRONT L Ve D Ee Wa 5 4 4 C j M 4 4 5 6 MIDNIGHT cu S 15 kDIGITALEQ kSURR BACK FMMODE 1005 M 6 e wor zP 8 w 9 AA t TVMIDEO CH LEVEL TVVOL VOLUME V SVIII MUTING 18 Ly REC PAUSE Ae S 20 SLEEP DOWN TUNING UP Y
127. e turning on speakers again as its high volume may come out of the speakers Activating and Adjusting the Subwoofer Sound You can cancel the subwoofer sound even though you have connected a subwoofer and have set SUB WOOFER to YES see page 27 This is useful when enjoying surround sound at night JVC L 3 o o P cu Press SUBWOOFER OUT ON OFF to cancel the subwoofer sound output Each time you press the button subwoofer sound output is deactivated SUBWFR OFF and activated SUBWFR ON alternately When subwoofer sound output is activated subwoofer output level can be adjusted using the remote control 1 Press SOUND 2 Press SUBWOOFER 3 Press LEVEL or to adjust the output level 10 dB to 10 dB Note You cannot deactivate the subwoofer sound output when you set SMALL for the front speakers on the Speaker size setting see page 27 or Quick Speaker Setup see page 25 Selecting the Analog or Digital Input Mode When you have connected digital source components using the digital terminals see page 16 change the input mode for these components to the digital input mode c 6 SSS INNEN d Before you start remember The digit
128. ecalls the memorized settings and adjustments see pages 25 to 33 You can also use the buttons on the remote control for the same functions Bl Activating the EX ES setting For multi channel digital software you can activate the EX ES 7 1 channel reproduction mode Once you have set EX ES 7 1 channel reproduction mode it is stored in memory and will be called up whenever you activate the Surround mode which the memorized EX ES 7 1 channel reproduction mode can be applied to xl o o 2 000000 o o 2 e ooo Press EX ES to select an appropriate setting for your enjoyment The currently selected EX ES 7 1 channel reproduction mode appears on the display Each time you press the button it changes as follows EX ES AUTO According to the incoming signal an appropriate Surround mode is applied For Dolby Digital EX and DTS ES EX ES 7 1 channel reproduction is applied For 5 1 channel or less encoded software 5 1 channel reproduction is applied EX ES ON Select to apply EX ES 7 1 channel reproduction to both 5 1 channel and 6 1 channel encoded software EX ES OFF Select to cancel the EX ES 7 1 channel reproduction f the surround back speakers not connected or deactivated Virtual 6 1 channel surround is applied Notes When Surround mode is deactivated pressing
129. ection buttons or the control button CONTROL for RX 8030VBK or TAPE CDR CONTROL for RX 7030VBK to activate the buttons for the target source If you press one of the source selection buttons the playing source also changes On the other hand pressing the control button does not change the playing source 45 Operating Video Components IMPORTANT To operate JVC s video components using the supplied remote control You need to connect JVC s video components through the AV COMPU LINK jacks see page 42 in addition to the connections using cables with RCA pin plugs see pages 14 and 15 Some JVC s VCRs can accept two types of the control signals remote code A and Before using this remote control make sure that the remote control code of the target VCR is set to code For RX 8030VBK When another JVC s VCR is connected to the VCR 2 or VIDEO terminals set its remote control code to code B This remote control cannot emit the control signals of code B When using the remote control aim the remote control directly at the remote sensor on each component not on the receiver For RX 8030VBK RX 8030V When you press one of the source selection Ea buttons the operation mode appears on the display window Buttons Indications VCR 1 VCR 1 DVD or DVD MULTI DVD TV DBS TV CONTROL repeatedly ho cde pos CDDSC CDR lt
130. ed A standard type connector should be connected to the FM 75 COAXIAL terminal Note If reception is poor connect the outdoor FM antenna not supplied Before attaching a 75 Q coaxial cable with a connector the kind with a round wire going to an outdoor antenna disconnect the supplied FM antenna AM Antenna Connections Turn the loop until you have the best reception IS sil Pa SH i AM Loop Antenna gill supplied Snap the tabs on the loop into the slots of the base to assemble the AM loop FM 750 COAXIAL Outdoor single vinyl covered wire not supplied Notes e f the AM loop antenna wire is covered with vinyl remove the vinyl by twisting it as illustrated e Make sure the antenna conductors do not touch any other terminals connecting cords and power cord This could cause poor reception f reception is poor connect an outdoor single vinyl covered wire not supplied to the AM EXT terminal Keep the AM loop antenna connected Connecting the Speakers You can connect the following speakers Two pairs of front speakers to produce normal stereo sound One pair of surround speakers to enjoy the surround effect One surround back speaker or one pair of surround back speakers to enjoy to produce more effective surround effect One center speaker to emphasize human voices One subwoofer to e
131. el DUAL Setting the Digital Input Terminals Setting the Component Video Input Memorizing the Volume Level for Each Source Adjusting Sound Basic Setting Items 2o 60n00 gear emetetetee mn Basic Pr cedute sortie rr eH acordes Adjusting the Speaker Output Levels Adjusting the Sound Parameters for the Surround and DSP modes sss Using the Surround Modes Reproducing Theater Ambience seen Introducing the Surround Modes sss Surround Modes Applicable to the Various Software Activating the Surround Modes sss W Activating the EX ES setting see B Activating the Surroung modes sss Using the DSP Modes Reproducing the Sound Field sss Introducing the DSP Modes eee Activating the DSP Modes teret Using the DVD MULTI Playback Mode Activating the DVD MULTI Playback Mode COMPU LINK Remote Control System AV COMPU LINK Remote Control System Operating JVC s Audio Video Components Operating Audio Components eene Operating Video Components
132. er output level CENTER LVL Select to adjust the center speaker output level SURRLLVL Select to adjust the left surround speaker output level SURRRLVL Select to adjust the right surround speaker output level SBACK LVL Select to adjust the surround back speaker output level Notes e If you have selected NO or NONE for a speaker see page 27 the output level for the corresponding speaker is not adjustable The center speaker and left right surround speakers output levels are adjustable for DVD MULTI playback mode even though is selected for the speaker settings Speaker output levels except the subwoofer output level are not adjustable when Analog Direct is in use To adjust subwoofer output level see page 19 You can also use the remote control for adjusting the speaker output level When using the remote control you can make an adjustment while listening to test tone Gio so c VN LYS gt od O 7 1 Press SOUND The 10 keys are activated for sound adjustments 2 Press TEST to check if you can hear the sounds through all the speakers at equal level Test tone comes out of the speakers in the following order No test tone comes out of the deactivated speakers and the subwoofer FRNT L Left front speaker gt CENTER Center speaker gt FRNT R Right front speaker SURR R Right surround speaker gt S BACK
133. expose this appliance to rain or moisture ATTENTION Afin d viter tout risque d lectrocution d incendie etc 1 Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l appareil 2 Ne pas exposer l appareil la pluie ni l humidit Caution 0 1 STANDBY ON button Disconnect the mains plug to shut the power off completely The 0 1 STANDBY ON button in any position does not disconnect the mains line The power can be remote controlled Attention Commutateur STANDBY ON D connecter la fiche de secteur pour couper compl tement le courant Le commutateur 2 1 STANDBY ON ne coupe jamais compl tement la ligne de secteur quelle que soit sa position Le courant peut tre t l command Note to CATV system installer This reminder is provided to call the CATV system installer s attention to Section 820 40 of the NEC which provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical For U S A This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance wi
134. f the next track Stop playing or recording Pause playing To resume press REC PAUSE Enter recording pause by pressing this button To start recording again press this button then Selecting TAPE will allow you to control the MD recorder Note You can use either source selection buttons or the control button CONTROL for RX 8030VBK or TAPE CDR CONTROL for RX 7030VBK RX 7032VSL to activate the buttons for the target source If you press one of the source selection buttons the playing source also changes On the other hand pressing the control button does not change the playing source 45 Operating Video Components IMPORTANT To operate JVC s video components using the supplied remote control You need to connect JVC s video components through the AV COMPU LINK jacks see page 42 in addition to the connections using cables with RCA pin plugs see pages 14 and 15 Some JVC s VCRs can accept two types of the control signals remote code A and Before using this remote control make sure that the remote control code of the target VCR is set to code For RX 8030VBK When another JVC s VCR is connected to the VCR 2 or VIDEO terminals set its remote control code to code This remote control cannot emit the control signals of code B When using the remote control aim the remote control directly at the remote sensor on each component
135. for RX 8030VBK or VCR CONTROL for RX 7030VBK RX 7032VSL to activate the buttons listed above If you press one of the source selection buttons the playing source also changes On the other hand pressing the control button does not change the playing source DVD player After pressing DVD or DVD MULTI you can perform the following operations on a DVD player gt Start playing I Return to the beginning of the current or previous chapter gt l Skip to the beginning of the next chapter Stop playing Pause playing To resume press After pressing DVD or DVD MULTI these buttons can be used for the DVD menu operations Note CG 5 a For detailed menu operations refer to the instructions supplied with the discs or the 8 v DVD player TV You can always perform the following operations TV OMI Turn on or off the TV TV VOL Adjust the volume TV VIDEO Set the input mode either TV or VIDEO After pressing TV DBS you can perform the following operations on a TV CH Change the channels 1 9 0 100 Select the channels RETURN Alternate between the previously selected channel and the current channel m Operating Other Manufacturers Video Equipment This remote control supplied with the receiver can transmit control signals for other manufacturers TVs CATV converters DBS tuners VCRs and DVD players When operating the other manufacturers
136. g you can adjust the EX ES 7 1 channel reproduction mode and store the setting but it will not affect the current source When the source is one to which the EX ES 7 1 channel reproduction cannot be applied you can adjust the setting and store in memory but reproduction channels will remain unchanged JVC OL SSS E c co Ec 1 Select and play any source other than DVD MULTI Make sure you have selected the analog or digital input mode Surround modes are not valid for DVD MULTI playback mode 2 Press SURROUND to activate the Surround mode For multi channel digital software except 2 channel and Dual Mono software incoming signals are automatically detected and the appropriate surround mode is activated see page 36 for details DIGITAL AUTO i ure DOpiarat RS Ex When DOLBY D is activated If the EX ES 7 1 channel reproduction mode has been set to AUTO or ON one of the EX ES 7 1 channel reproduction modes will be activated see the left column For analog sources and digital 2 channel software you can select one of the following Surround modes Each time you press SURROUND Surround modes change as follows fe MOVIE PL I MUSIC PRO dl NEO
137. g DVD or DVD MULTI you can perform the following operations on a DVD player gt Start playing lt Return to beginning of the current or previous chapter gt gt Skip to the beginning of the next chapter Stop playing Pause playing To resume press After pressing DVD or DVD MULTI these buttons can be used for the DVD 2 a 3 menu operations Note e ORO For detailed menu operations refer to the 8 instructions supplied with the discs or the DVD player 5 Try to operate your DVD player by pressing one of the above buttons DO NOT forget to turn on a DVD player before pressing one of the above buttons If there are more than one code listed for your brand of DVD try each one until the correct one is entered For TV For VCR JVC 00 02 13 52 53 54 55 14 47 74 56 57 58 59 Akai 01 02 60 61 62 63 Blaupunkt 03 04 64 65 66 67 Fisher 01 05 RCA 08 24 29 30 Grundig 03 06 07 Proscan 31 48 Hitachi 08 09 10 49 SABA 32 33 68 69 Irradio 02 70 ITT NOKIA 11 12 Samsung 06 08 16 34 Loewe 06 15 16 35 49 Magnavox 08 17 49 Sanyo 01 05 Mets 50 51 52 53 Schneider 02 15 36 Mitsubishi 08 18 19 20 Sharp Mivar 21 Sony Nordmende Telefunken 40 41 42 69 Okano Thomson 71 72 24 25 26 27 Toshiba 37 43 44 76 Zenith 45 46 Philips 15 17 28 75 Manufacturer JVC Aiwa Bell amp Howe
138. guration Quick Speaker Setup helps you to easily and quickly register the speaker size and speaker distance according to your listening room to create the best possible surround effect You can also register each speaker s information manually For details see page 27 000 S 00 o o 000000 o o oo 9 Before you start remember There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again On the front panel 1 Press QUICK SPEAKER SETUP SETUP and SPEAKERS appear on the display then the initial setting for the total number of the connected speakers channels appears SPEAKERS 1 voLuue I 2 Turn MULTI JOG to select an appropriate number of the connected speakers speaker channel number The speaker channel number changes as follows For the details of speaker channel number see Speakers channels number and the size on page 26 SPEAKERS 1 voume IZ 21 3 1CH 6 0CH 6 1CH 7 1CH Back to the beginning 2 0CH 4 0CH gt 4 1CH 7 0CH gt 2 1CH 5 0CH 3 0CH 5 1CH gt 6 OCH is the initial setting 3 Press in MULTI JOG PUSH SET ROOM SIZE appear on the display then the initial room size setting appears SPEAKERS
139. h the digital input the dits indicator lights up on the display DTS Digital Surround DTS Digital Surround DTS is another discrete 5 1 channel digital audio format available on CD LD and DVD software Compared to Dolby Digital the DTS Digital Surround format has a lower audio compression rate which enables it to add breadth and depth to the sounds reproduced As such DTS Digital Surround features natural solid and clear sound When EX ES setting is set to ON DTS Neo 6 DTS NEO 6 is applied while playing back multi channel DTS software It creates the same surround ambience as 6 1 channel software does DTS Extended Surround DTS ES DTS ES is another multi channel digital encoding format It greatly improves the 360 degree surround impression and space expression by adding the third surround channel surround back channel DTS ES includes two signal formats with different surround signal recording methods DTS ES Discrete 6 1ch ES DSCRETE and DTS ES Matrix 6 1ch ES MATRIX DTS ES Discrete 6 1ch has been designed to encode and decode a 6 1 channel signal discretely to avoid interference with each channel DTS ES Matrix 6 1ch has been designed to add an extra surround channel to DTS Digital Surround 5 1 channel By using a matrix encoding decoding method an additional surround back channel signal is encoded and decoded in both the left and right surround channel signals e You can us
140. he DAP effect level As the number increases the DAP effect becomes stronger Normally select 3 initial setting Adjustable range 1 to 5 ROOMSIZE Adjust the virtual room size As the number increases the interval between reflections increases so that you will feel as if you were in a larger room Normally select 3 initial setting Adjustable range 1 to 5 LIVENESS Adjust the liveness effect As the number increases the attenuation level of reflections over time decreases so that acoustics change from Dead to Live Normally select 3 initial setting Adjustable range 1 to 5 For Pro Logic II Music only PANORAMA Select ON to add wraparound sound effect with side wall image Initial setting OFF CNTR WIDTH Adjust the center channel localization between the center speaker and the left right speakers As the number increases the center channel sound moves toward the left and right speakers Normally select 3 initial setting Adjustable range OFF and 1 to 7 DIMENSION Adjust sound localization position As the number increases the sound localization moves towards forward from backward Normally select 4 initial setting Adjustable range 1 to 7 For Neo 6 Music only CNTR GAIN Adjust the sound localization of the center channel As the number increases center channel will be localized clearly Normally select 0 2 initial setting
141. he Remote Control Before using the remote control insert the two supplied batteries first 1 2 3 R6P SUM 3 Bs a 1 Press and slide the battery cover on the back of the remote control 2 Insert the batteries e Make sure to match the polarity to and to gt 3 Replace the cover If the remote control cannot transmit signals or operate the receiver correctly replace the batteries Use two R6P SUM 3 AA 15F type dry cell batteries Notes Supplied batteries are for the initial setup Replace for continued use e After replacing the batteries set the manufacturers codes again see pages from 47 to 49 CAUTION Follow these precautions to avoid leaking or cracking cells Place batteries in the remote control so they match the polarity to and to Use the correct type of batteries Batteries that look similar may differ in voltage Always replace both batteries at the same time Do not expose batteries to heat or flame Connecting the FM and AM Antennas FM Antenna Connections FM Antenna supplied Extend the supplied FM antenna horizontally Outdoor FM Antenna Cable not supplied A Using the Supplied FM Antenna The FM antenna provided can be connected to the FM 75 Q COAXIAL terminal as temporary measure B Using the Standard Type Connector Not Suppli
142. he right channel signal comes in When analog input is selected Always lights up C Lights up when the center channel signal comes in LFE Lights up when the LFE channel signal comes in LS Lights up when the left surround channel signal comes in RS Lights up when the right surround channel signal comes in S Lights up when the monaural surround channel signal comes in SB Lights up when the surround back channel signal comes in Note When DVD MULTI is selected as the source L C LFE LS and RS light up How to understand the speaker and signal indicator illumination C R Ex No sound comes out of the center speaker and surround back speakers though center SB channel and surround back channel signals are coming into this receiver 18 Selecting different sources for picture and sound While watching pictures from a video source you can listen to sound of an audio source Once you have selected a video source pictures of the selected source are sent to the TV until you select another video source Press one of the audio source selection buttons while viewing the picture from a video component such as the VCR or DVD player etc For RX 8030VBK CD FMAM C oC D a o a o TAPE MD PHONO cb COR TAPEMD FM AM On the unit On the remote For RX 7030VBK cD FM AM cD TAPE CDR FM AM TAPEICDR On the un
143. he signal indicators light up to show the incoming signals L When digital input is selected Lights up when the left channel signal comes in When analog input is selected Always lights up R When digital input is selected Lights up when the right channel signal comes in When analog input is selected Always lights up C Lights up when the center channel signal comes in LFE Lights up when the LFE channel signal comes in LS Lights up when the left surround channel signal comes in RS Lights up when the right surround channel signal comes in S Lights up when the monaural surround channel signal comes in SB Lights up when the surround back channel signal comes in Note When DVD MULTI is selected as the source L C R LFE LS and RS light up How to understand the speaker and signal indicator illumination C Ex No sound comes out of the center speaker and surround back speakers though center S channel and surround back channel signals are coming into this receiver 18 Selecting different sources for picture and sound While watching pictures from a video source you can listen to sound of an audio source Once you have selected a video source pictures of the selected source are sent to the TV until you select another video source Press one of the audio source selection buttons while viewing the picture from a video component such as the V
144. hich adds a function to the previous version in order to operate JVC s video components through the video components terminals To use this remote control system connect the video components you want to operate following the diagrams below and the procedure on the next page CONNECTIONS 1 AV COMPU LINK Connection IMPORTANT DVD player TV COMPULINK CAUTION You can only connect to the TV MlM _ with the AV COMPU LINK EX or AV COMPU LINK III jack DO NOT connect to the TV with AV COMPU LINK RECEIVER AMP jack COMPU LINK The AV COMPU LINK remote control system cannot control the DBS tuner For RX 8030VBK Connect the VCR to the VCR 1 jacks Video components connected to the VIDEO and VCR 2 jacks on the receiver cannot be controlled with the AV COMPU LINK remote control system Notes When connecting the receiver and a TV with the AV COMPU LINK EX terminal by using a component video cable you cannot use automatic selection of TV s input mode see page 43 When connecting only the VCR or DVD player to this receiver connect it directly to the receiver using cables with the monaural mini plugs CONNECTIONS 2 Video Cable Connection This receiver is equipped with three types of the video terminals S video composite video and component video and the signals coming into this receiver through one type of video jacks can output only through the jack of the same type So you need to connect the
145. hones If you press DSP when the front speakers 1 and 2 are both deactivated 3D HEADPHONE mode is activated without respect to the type of software played back 3D H PHONE appears on the display and the DSP and HEADPHONE indicators also light up 38 To use the DSP modes press DSP so that the DSP modes change as follows The DSP indicator also lights up on the display HALL 1 gt HALL 2 LIVE CLUB gt DANCE CLUB PAVILION ALL STEREO THEATER 1 gt THEATER2 MONO FILM Back to the beginning Suitable for audio sources Suitable for video sources DAP modes You can use the following DAP modes in order to reproduce a more acoustic sound field in your listening room HALL 1 Reproduces the spatial feeling of a large shoebox shaped hall designed primarily for classical concerts Its seating capacity is about 2000 Reproduces the spatial feeling of a large vineyard shaped hall designed primarily for classical concerts Its seating capacity is about 2000 Reproduces the spatial feeling of a live music club with a low ceiling HALL 2 LIVE CLUB DANCE CLUB Reproduces the spatial feeling of a rocking dance club PAVILION Reproduces the spatial feeling of an exhibition hall with a high ceiling THEATER 1 Reproduces the spatial feeling of a large theater where the seating capacity is about 60
146. ies of components To operate the target component using the COMPU LINK remote control system set the source name correctly if required See page 21 Refer also to the manuals supplied with your audio components This remote control system allows you to use four functions listed below Remote Control through the Remote Sensor on the Heceiver You can control the connected audio components through the remote sensor on the receiver using this remote control Aim the remote control directly at the remote sensor on the receiver For details see pages 44 and 45 Automatic Source Selection When you press the play gt button on a connected component or on its own remote control the receiver automatically turns on and changes the source to the component On the other hand if you select a new source on the receiver or on the remote control the selected component begins playing immediately In both cases the previously selected source continues playing without sound for a few seconds For RX 7030VBK You cannot use the COMPU LINK remote control system to operate the MD recorder Automatic Power On Off Standby only possible with the COMPU LINK 3 and COMPU LINK 4 The connected components turn on and off standby along with the receiver When you turn on the receiver one of the connected components will turn on automatically depending on which component has been previously selected When you turn off the receiver
147. ights up when DTS signals come in MID NIGHT 1 Select when you want to reduce the dynamic range a little No indicator lights up when the receiver cannot recognize the MID NIGHT 2 Select when you want to apply the compress digital signal format of the incoming signals When playing software encoded with the Dolby Digital or DTS the following symptoms may occur Sound does not come out at the beginning of playback Noise comes out while searching for or skipping chapters or tracks DGTL D D or DGTL DTS while DGTL AUTO still remains on the display As you press INPUT DIGITAL the input mode changes as follows In this case press INPUT DIGITAL repeatedly to select DIGITAL AUTO OO DIGITAL DGTL AUTO DGTL D D Digital Dolby Dia DGTL DTS When DGTL or DGTL DTS is selected the AUTO indicator goes off and the corresponding digital signal format indicator lights up on the display If the incoming signal does not match the selected digital signal format the frame of the selected indicator will flash Note When you turn off the power or select another source DGTL D D and DGTL DTS settings are canceled and the digital input mode is automatically reset to DGTL AUTO To select the analog input mode again Press INPUT ANALOG or press ANALOG DIGITAL INPUT on the remote control repeatedly until ANALO
148. iled menu operations refer to the instructions supplied with the discs or the DVD player 5 Try to operate your DVD player by pressing one of the above buttons DO NOT forget to turn on a DVD player before pressing one of the above buttons If there are more than one code listed for your brand of DVD try each one until the correct one is entered For TV 00 02 13 Quelle 14 47 74 01 02 03 04 64 65 66 67 01 05 RCA 03 06 07 Proscan 08 24 29 30 31 48 08 09 10 49 SABA 02 32 38 68 69 70 ITT NOKIA 11 12 Samsung Loewe 06 15 16 06 08 16 34 35 49 Magnavox 08 17 49 Sanyo 01 05 Mets 50 51 52 53 Schneider 02 15 36 37 38 77 Mitsubishi 08 18 19 20 Sharp 21 Mivar Sony 39 Nordmende Telefunken 40 41 42 69 Okano Thomson 11 72 Panasonic 24 25 26 27 Toshiba 76 37 43 44 Zenith 45 46 Philips 15 17 28 75 JVC For DBS tuner 56 57 67 Amstrad 43 44 45 46 47 48 49 Blaupunkt 30 Echostar 50 51 67 Goldstar Grundig Hirshmann Instrument ITT NOKIA Kathrein NEC Orbitech Philips RCA Samsung Schwaiger Siemens Sony Technisat For CATV converter 06 07 08 09 10 11 12 13 14 29 General Inst
149. in RMS driven into 8 Q at 1 kHz with no more than 0 8 total harmonic distortion Center ch 110 W min RMS driven into 8 Q at 1 kHz with no more than 0 8 total harmonic distortion Surround ch 110 W per channel min RMS driven into 8 Q at 1 kHz with no more than 0 896 total harmonic distortion Surround Back ch 110 W min RMS driven into 8 Q at 1 kHz with no more than 0 8 total harmonic distortion Audio Audio Input Sensitivity Impedance 1 kHz DVD IN VCR IN TV SOUND DBS IN CD IN TAPE CDR IN Audio Input DIGITAL IN Coaxial DIGITAL 1 DVD 0 5 V p p 75 Q Optical DIGITAL 2 CD DIGITAL 3 TV DIGITAL 4 CDR 21 dBm to 15 dBm 660 nm 30 nm Corresponding to Linear PCM Dolby Digital and DTS Digital Surround with sampling frequency 32 kHz 44 1 kHz 48 kHz 200 mV 47 200 mV 47 Audio Output Level SUBWOOFER OUT 1V Recording Output Level VCR OUT TAPE CDR OUT 200 mV Digital output Optical DIGITAL OUT Signal wave length 660 nm Output level 21 dBm to 15 dBm Signal to Noise Ratio 66 IHF 78 IHF DVD IN VCR IN TV SOUND DBS IN CD IN TAPE CDR IN Frequency Response 8 Q DVD IN VCR IN TV SOUND DBS IN 20 Hz to 100 kHz 1 dB 3 dB 20 Hz to 100 kHz 1 dB 3 dB 87 dB 80 dB 87 dB 80 dB CD IN TAPE CDR IN 52 Equalization 5 bands 63 Hz 250 Hz 1 kHz 4 kHz 16 kHz 8 dB Bass boost 6 dB 1 0 dB at 100 Hz Video Video Input Sensitivity Impe
150. inals 10 Earth ground terminal 11 Differences between RX 8O30VBK and RX 7030VBK Video jacks input output PREOUT jacks RX 7030VBK 1 CC Converter DIGITAL IN terminals 16 Coaxial DIGITAL 1 DVD Optical DIGITAL 2 CD DIGITAL 3 TV DIGITAL 4 CDR AUDIO input output jacks 12 15 Input DVD IN FRONT CENTER SUBWOOFER SURR REAR TV SOUND DBS IN VCR IN PLAY TAPE CDR IN PLAY CD IN Output VCR OUT REC TAPE CDR OUT REC S VIDEO and composite VIDEO input output jacks 14 15 e Input IN TV SOUND DBS IN VCR IN PLAY Output VCR OUT REC MONITOR OUT FM AM ANTENNA terminals 8 SUBWOOFER OUT jack 10 COMPONENT VIDEO input output jacks 14 15 e Input DVD IN DBS IN Output MONITOR OUT COMPU LINK 4 SYNCHRO terminals 41 AV COMPULINK III terminals 42 AC power cord 16 DIGITAL OUT terminal 16 SURROUND BACK SPEAKERS terminal 10 SURROUND SPEAKERS terminal 10 CENTER SPEAKER terminal 10 FRONT SPEAKERS 0 terminals 10 FRONT SPEAKERS 2 terminals 10 Q Supplied Selectable source x Not supplied RX 8030VBK Composite video 4 3 DVD MULTI DVD VCR 1 VCR 2 VIDEO S video 4 3 Q TV SOUND DBS PHONO CD CDR TAPE MD Component video 2 1
151. ing during record playing A ground cable from the turntable is not connected to the screw marked 5 on the rear Connect the cable to the screw marked 75 on the rear Your turntable is too close to the speakers Move the speakers away from the turntable No sound effect such as Surround mode DSP mode and Digital Equalization Analog Direct is turned on Turn off Analog Direct See page 21 DVD MULTI is selected as the source Select the source other than DVD MULTI See page 40 EX ES 7 1 channel reproduction cannot be done for Dolby Digital EX or DTS ES software Software or setting is not for Dolby Digital EX or DTS ES software Play back software bearing the mark 00297 or Eres Set EX ES setting to ON See page 37 OVERLOAD starts flashing on the display Speakers are overloaded because of high volume 1 Press O ISTANDBY ON on the front panel to turn off the receiver 2 Stop the playback source 3 Turn on the receiver again and adjust the volume Speakers are overloaded because of short circuit of speaker terminals Press 0 1 STANDBY ON on the front panel to turn off the receiver then check the speaker wiring If OVERLOAD does not disappear unplug the AC power cord then plug it back again If speaker wiring is not short circuited contact your dealer The STANDBY lamp lights up after turning on the power and
152. ion so that you can view the playback picture When you insert a video cassette with its safety tab press the play gt button on the VCR or on the remote control So you can get the same result One Touch DVD Play Simply by starting playback on the DVD player you can enjoy the DVD playback without setting other switches manually When the DVD player is connected through the analog input jacks on this receiver and analog input is selected the receiver automatically turns on and changes the source to DVD or DVD MULTI When the DVD player is connected through the digital input terminal on this receiver and digital input is selected the receiver automatically turns on and changes the source to DVD The TV automatically turns on and changes the input mode to the appropriate position so that you can view the playback picture Automatic Selection of TV s Input Mode When you select TV as the source to play on the receiver the TV automatically changes the input mode to the TV tuner so that you can watch TV When you select any other video source other than TV as the source to play on the receiver the TV automatically changes the input mode to the appropriate position either Video Input 1 or Video Input 2 so that you can view the playback picture Notes e When you select TV as the source on the receiver you cannot see the menu on the TV screen since the AV COMPU LINK remote control
153. it On the remote Note When you see the picture through the COMPONENT VIDEO jacks you cannot use this function Adjusting the Volume Jvc L oo 000000 eo the front panel To increase the volume turn MASTER VOLUME clockwise To decrease the volume turn it counterclockwise From the remote control To increase the volume press VOLUME To decrease the volume press VOLUME CAUTION Always set the volume to the minimum before starting any sources If the volume is set at its high level the sudden blast of sound energy can permanently damage your hearing and or ruin your speakers Notes The volume level can be adjusted within the range of 0 minimum to 70 maximum If you set One Touch Operation to ON see page 30 you do not have to adjust the volume level each time you change the source It is automatically set to the stored level Selecting the Front Speakers When you have connected two pairs of the front speakers you can select which to use o o cor 000000 o o oo To use the speakers connected to the FRONT SPEAKERS D terminals press SPEAKERS ON OFF 1 so that the SPEAKERS 1 indicator lights up on the display Make sure th
154. ital audio format available on CD LD and DVD software Compared to Dolby Digital the DTS Digital Surround format has a lower audio compression rate which enables it to add breadth and depth to the sounds reproduced As such DTS Digital Surround features natural solid and clear sound e When EX ES setting is set to ON DTS Neo 6 DTS NEO 6 is applied while playing back multi channel DTS software It creates the same surround ambience as 6 1 channel software does DTS Extended Surround DTS ES DTS ES is another multi channel digital encoding format It greatly improves the 360 degree surround impression and space expression by adding the third surround channel surround back channel DTS ES includes two signal formats with different surround signal recording methods DTS ES Discrete 6 1ch ES DSCRETE and DTS ES Matrix 6 1ch ES MATRIX DTS ES Discrete 6 1ch has been designed to encode and decode a 6 1 channel signal discretely to avoid interference with each channel DTS ES Matrix 6 1ch has been designed to add an extra surround channel to DTS Digital Surround 5 1 channel By using a matrix encoding decoding method an additional surround back channel signal is encoded and decoded in both the left and right surround channel signals You can use Virtual 6 1 channel surround when playing back DTS ES software without connecting the surround back speakers This surround reallocates the surround back
155. kers Center speaker Right Left Right Left CAUTION SPEAKER IMPEDANCE on s0 160 ee RIGHT LEFT RIGHT LEFT FRONT SPEAKERS SINGLE USE See Instruction Manual For Connection RIGHT SURROUND BACK SPEAKERS LEFT RIGHT SURROUND PEAKERS LEFT E CENTER SPEAKER 160 320 IMPORTANT After connecting the speakers set the speaker installation information properly You can use Quick Speaker Setup for When using only one surround back speaker connect the to the RIGHT terminal and the Surround speakers EASY speaker installation information setting see page 25 cord to the LEFT Right P To obtain the best possible Surround DSP effect see Setting terminal the Speakers on page 27 Connecting the subwoofer speaker You can enhance the bass by connecting a subwoofer Ei Connect the input jack of a powered subwoofer to the rear panel using a cable with RCA in plugs not supplied DEUM RX 8030VBK oe RX 7032VSL SINGLE USE PREOUT SUBWOOFER See Instruction Manual For Connection xe e OOXO SUBWOOFER RIGHT LEFT SURROUND BACK SPEAKERS St Placing speakers Front speakers and center speaker Place these speakers position of the mid range speaker u
156. lby Pro Logic Dolby Surround encoding format records the left front channel right front channel center channel and surround channel monaural signals into 2 channels The Dolby Pro Logic PRO LOGIC decoder built in this receiver decodes these 2 channel signals into 4 original channel signals plus subwoofer matrix based multi channel reproduction e When Dolby Pro Logic is activated the D0 PRO LOGIC indicator lights up on the display Dolhy Pro Logic II Dolby Pro Logic II is a multi channel playback format to convert 2 channel software into 5 channel plus subwoofer The matrix based conversion method used for Dolby Pro Logic II makes no limitation for the cutoff frequency of the surround treble and enables stereo surround sound This receiver provides two types of Dolby Pro Logic II modes Pro Logic II Movie PLII MOVIE and Pro Logic II Music PLII MUSIC When Dolby Pro Logic II is activated the DO PRO LOGIC II indicator lights up on the display PLII MOVIE Suitable for playing any Dolby Surround encoded software You can enjoy a sound field very close to the one created with discrete 5 1 channel sounds PLII MUSIC Suitable for playing any 2 channel stereo software You can enjoy wide and deep sounds DTS DTS is another digital signal compression method developed by Digital Theater Systems Inc and enables multi channel encoding and decoding 1ch up to 6 1ch When DTS signal is detected throug
157. ld CATV DBS cort 2 Press CATV DBS CONTROL For RX 8030VBK CALL appears on the display window of the remote control 3 Enter a manufacturer s code using buttons 1 9 and 0 See the list on page 49 to find the code 4 Release CATV DBS cori The following buttons can be used for operating a CATV converter and DBS tuner CATV DBS I Turn on and off a CATV converter or DBS tuner After pressing CATV DBS CONTROL you can perform the following operations on a CATV converter or DBS tuner CH Change the channels 1 10 0 0 100 10 Select the channels The 10 0 button will function as the ENTER button if your equipment requires pressing ENTER after selecting a channel number 5 Try to operate your CATV converter or DBS tuner by pressing CATV DBS When your CATV converter or DBS tuner turns on or off you have entered the correct code If there are more than one code listed for your brand of CATV converter or DBS tuner try each one until the correct one is entered Note You cannot preset the signals for both the CATV converter and DBS tuner at the same time 47 To change the transmittable signals for operating another manufacturer s VCR 1 Press and hold VCR 1 for RX 8030VBK or VCR for RX 7030VBK RX 7032VSL 2 Press VCR 1 for RX 8030VBK or VCR for RX 7030VBK RX 7032VSL For RX 8030VBK CALL appears on the display window of the remote control 3 Ente
158. lected band is tuned in AUTOMUTING Normally select this Each time you press the button the band alternates between When a program is broadcasted in stereo FM and AM you will hear stereo sound when in monaural you will hear monaural 2 Press the 10 keys to select a preset channel sounds number This mode is also useful to suppress static noise between stations The AUTO MUTING indicator lights up on the display Initial setting For channel number 5 press 5 For channel number 15 press 10 then 5 For channel number 20 press 10 then 10 For channel number 30 press 10 10 then 10 MODE MONO Select this to improve the reception but stereo effect will be lost In this mode you will hear noise while Note tuning into the stations The AUTO ETE MUTING indicator goes off from the display The STEREO indicator also goes off When you use the 10 keys on the remote control be sure that they are activated for the tuner not for the CD and others See page 44 Note When you use the FM MODE on the remote control be sure that it is activated for the tuner not for the CD and others See page 44 24 m Basic Settings Some of the following settings are required after connecting and positioning your speakers while others will make operations easier You can use QUICK SPEAKEH SETUP to easily set up your speaker configuration Setting the Speakers Configuration Quick Speaker Setup helps you
159. ll Blaupunkt CGM Emerson 08 10 11 12 64 65 Fisher 03 14 15 16 17 Goldstar Goodmans Grundig Hitachi 18 23 24 25 66 Loewe 07 21 Magnavox 04 19 24 Mitsubishi 30 31 32 33 34 35 NEC 26 27 Nokia Nordmende Orion For DBS tuner Panasonic 19 24 39 40 Philips 04 19 21 24 41 42 Phonola 21 RCA Proscan 04 18 19 23 24 43 44 45 SABA 38 46 Samsung 45 47 59 61 62 63 Sanyo 03 48 49 Sharp 37 50 Siemens 03 51 Sony 52 53 54 Telefunken 55 60 Toshiba 43 44 Zenith 56 57 JVC 56 57 67 Amstrad 43 44 45 46 47 48 49 Blaupunkt Echostar Goldstar Grundig Hirshmann Instrument ITT NOKIA Kathrein NEC Orbitech Philips RCA Samsung Schwaiger Siemens Sony Technisat For DVD player Manufacturer JVC Denon 01 Panasonic 03 Philips 13 Pioneer 04 05 06 RCA 07 Samsung 08 Sony 09 12 13 14 29 Toshiba 10 Hamlin Regal 01 02 03 04 05 Yamaha Jerrold 06 07 08 09 10 11 nitial setting 12 13 14 For CATV converter General Instrument 06 07 08 09 10 11 Oak 15 16 17 Panasonic 18 19 20 Pioneer 21 22 Scientific Atlanta 23 24 25 Tocom 26 Manufacturers codes are subject to
160. m For RX 7030VBK You can use the BASS BOOST button on the front panel When the Bass Boost is activated the lamp on the button lights up Each time you press the button Bass Boost turns on and off Notes This function affects only the sounds from the front speakers center speaker and subwoofer When Analog Direct is in use see page 21 the Bass Boost is canceled temporarily Muting the Sound Press MUTING to mute the sound through all speakers and headphones connected MUTING appears on the display and the volume turns off the VOLUME level indicator goes off To restore the sound press MUTING again Turning MASTER VOLUME on the front panel or pressing VOLUME on the remote control also restores the sound Changing the Display Brightness You can dim the display Press DIMMER Each time you press the button the brightness level of the display change as follows Dimmer Much dimmer cm Canceled _ Normal display 22 Using the Sleep Timer Using the Sleep Timer you can fall asleep while listening to music When the shut off time comes the receiver turns off automatically Press SLEEP repeatedly The SLEEP indicator lights up on the display and the shut off time changes in 10 minutes intervals p MOSS 0 To check or change the time remaining until the shut off time Press SLEEP once The remaining time until the shut off time appears in minute
161. n the listener s Subwoofer You can place it wherever you like since bass sound is non directional Normally place it in front of you 9I ears Point these speakers down aiming at the listener s ears j j x V 2 UN 0 90 Note Ideal speaker layout requires that all speakers be placed at the same distance SB from the listener However since in some places it may be difficult to fulfil this requirement this unit can adjust the delay time so that the sounds through all the speakers reach the listener with the same timing See page 28 10 When one surround back speaker is connected Enhancing your audio system RX 8030V Connecting Audio Video Components Only for RX 8030VBK gum You can use this receiver as the pre amplifier control amplifier When connecting individual components refer also to the manuals when you connect power amplifiers to the PREOUT jacks on the supplied with them rear using cables with RCA pin plugs not supplied Connect the white plug to the audio left jack and the red plug to Bl Analog Connections the audio right jack If your audio components have digital audio output terminal connecting them using the digital cords explained in Digital Connections see page 16 will give you better sound quality Audio component connections Use the cables with RCA pin plugs not supplied Connect the white plug to the audio left jack an
162. nals S video composite video and component video and the signals coming into this receiver through one type of video jacks can output only through the jack of the same type So you need to connect the VCR and or DVD player to the TV using one of the following three ways When using the AV COMPU LINK remote control system set the component video input for the DVD player and the DBS tuner correctly see Setting the Component Video Input on page 30 otherwise the correct input for this receiver will not be selected on the TV When connecting the source equipment to the receiver through the S video jacks connect this receiver to the TV s Video Input 1 jack using S video cables Source RX 8030VBK equipment RX 7030VBK TV SEDI end RX 7032VSL S video cord To video Input 1 When connecting the source equipment to the receiver through the composite video jacks connect this receiver to the TV s Video Input 2 jack composite video input using composite video cables Source RX 8030VBK t RX 7030VBK TV equipmen Composite RX 7032VSL Composite video cord video cord To video Input 2 When connecting the source equipment to the receiver through the component video jacks connect this receiver to the TV s Video Input 2 jack component video input using component video cables Source RX 8030VBK brieni RX 7030VBK TV equipme Component RX 7032VSL Component video cord video cord To video Input 2
163. nect the surround back speaker to the left surround back PREOUT jack SURR BACK L 11 CD player To listen to the sound after connection press CD CJ RX 8030VBK RX 7030VBK RX 7032VSL CD player To audio output Cassette deck To listen to the sound after connection press TAPE MD for RX 8030VBK or TAPE CDR for RX 7030VBK RX 7032VSL For RX 8030VBK You can connect either a cassette deck or an MD recorder to the TAPE MD jacks When connecting an MD recorder see page 13 RX 8030VBK Cassette deck For RX 7030VBK RX 7032VSL You can connect either a cassette deck or a CD recorder to the TAPE CDR jacks When connecting an CD recorder to the TAPE CDR jacks see the right column LI CI RX 7030VBK RX 7032VSL Cassette deck To audio input To audio output 12 CD recorder To listen to the sound after connection press CDR for RX 8030VBK or TAPE CDR for RX 7030VBK RX 7032VSL For RX 8030VBK RX 8030VBK CD recorder To audio input To audio output For RX 7030VBK RX 7032VSL You can connect either a CD recorder or a cassette deck to the TAPE CDR jacks When connecting a cassette deck to the TAPE CDR jacks see the left column RX 7030VBK RX 7032VSL CD recorder To audio input To audio output gt Note For RX 7030VBK RX 7032VSL When connecting a CD recorder to the TAPE CDR jacks change the s
164. ng 1ch up to 5 1ch When Dolby Digital signal is detected through the digital input the indicator lights up on the display Dolhy Digital 5 1CH Dolby Digital 5 1CH DOLBY D encoding method records and digitally compresses the left front channel right front channel center channel left surround channel right surround channel and LFE channel signals total 6 channels but the LFE channel is counted as 0 1 channel Therefore called 5 1 channel Dolby Digital enables stereo surround sounds and sets the cutoff frequency of the surround treble at 20 kHz compared to 7 kHz for Dolby Pro Logic As such the sound movement and being there feeling are enhanced much more than Dolby Pro Logic Dolby Digital EX Dolby Digital EX DOLBY D EX is a digital surround encoding format that adds the third surround channels called surround back Compared to the conventional Dolby Digital 5 1CH these newly added surround back channels can reproduce more detailed movements behind you while viewing the video software In addition surround sound localization will become more stable You can use Virtual 6 1 channel surround when playing back Dolby Digital EX software without connecting the surround back speakers This surround reallocates the surround back channel to the surround speakers so that you can still feel the great surround effect from behind The VIRTUAL SB Surround Back indicator lights up on the display Do
165. ng the following steps If the setting is canceled before you finish start from step 1 again Ex When adjusting the subwoofer level to 3 1 Press ADJUST The last selected item appears on the display 2 Turn MULTI JOG until an item you want appears on the display n this example select SUBWFR LVL For available items see the list to the left 3 Press in MULTI JOG PUSH SET The current setting or level for the selected item appears on the display 4 Turn MULTI JOG to select a setting you want or to make an adjustment as you like voume I 5 Press EXIT 6 Repeat steps 2 to 5 to set other items if necessary 7 Press EXIT The source indication resumes on the display 31 Adjusting the Equalization Patterns Adjusting the Speaker Output Levels You can adjust the equalization patterns to your preference Once you have made adjustment it is memorized for each source You can adjust the speaker output levels The test tone comes out of each speaker except subwoofer to check the output level balance when using the Surround mode Once you have made an adjustment it is memorized for each m Equalization adjustment DIGITAL EQ You can adjust five frequency 63 Hz 250 Hz 1 kHz Source 4 kHz 16 kHz within the range of 8 dB to 8 dB 0 dB is the initial setting in 2 dB steps When adju
166. nhance the bass CAUTION Use only the speakers of the SPEAKER IMPEDANCE indicated by the speaker terminals When connecting to both of the FRONT SPEAKERS and 2 terminals use speakers with an impedance of 16 O to 32 Q When connecting to either the FRONT SPEAKERS or terminals use speakers with an impedance of 8 to 16 Q Basic connecting procedure 1 Twist and remove the insulation at 7 the end of each speaker signal cable not supplied 2 Open the speaker terminal RX 7030VBK For FRONT SPEAKERS 2 terminals 3 Insert the speaker signal cable For each speaker except for a subwoofer connect the and terminals on the rear panel to the and terminals marked on the speakers Speaker layout Ideal speaker layout varies depending on the conditions of your listening room The diagram below is a recommended typical example Subwoofer Left front speaker s Center speaker Right front speaker s L C R LR LN Left surround Right surround speaker LS speaker RS Surround back speakers LSB RSB Rear terminals of RX 8030VBK are used for explanation Front speakers 1 Front speakers 2 Surround back speakers Center speaker Right Left Right Left Right Left AUTION SPEAKER IMPEDANCE on s0 160 Oam 2 160 320 SINGLE USE See Instruction Manual Fo
167. nits at the same s Subwoofer height from the floor Point these speakers aiming at the listener s ears Surround and surround back speakers aM Place these speakers at a position which is 1 meter higher than the listener s z Point these speakers down aiming at the listener s ears Subwoofer bo You can place it wherever you like since bass sound is non directional Normally place it in front of you Note 6 Y ane Ln mid SB Ideal speaker layout requires that all speakers be placed at the same distance from the listener However since in some places it may be difficult to fulfil this requirement this unit can adjust the delay time so that the sounds through all the When one surround back speaker is speakers reach the listener with the same timing See page 28 connected 10 Enhancing your audio system RX 8030V Connecting Audio Video Components Only for RX 8OSOVBK You can use this receiver as the pre amplifier control amplifier When connecting individual components refer also to the manuals when you connect power amplifiers to the PREOUT jacks on the supplied with them rear using cables with RCA pin plugs not supplied Connect the white plug to the audio left jack and the red plug to the audio right jack If your audio components have digital audio output terminal connecting them using the digital cords explained in Digital Connections see page 16 will give
168. not on the receiver For RX 8030VBK RX 8030V When you press one of the source selection buttons the operation mode appears on the display window Buttons Indications VCR 1 VCR 1 DVD or DVD MULTI DVD TV DBS TV VCR1 TAPE CONTROL repeatedly CDDSC lt CDR i By pressing CONTROL repeatedly you can select VCR 1 TAPE CDR or CDDSC as the source When you press one of the buttons listed above the remote operation mode appears on the operation mode display for about two hours VCR You can always perform the following operations VCR 1 l for RX 8030VBK or VCR Q l for RX 7030VBK RX 7032VSL Turn on or off a VCR For RX 8030VBK After pressing VCR 1 or selecting VCR 1 by pressing CONTROL repeatedly you can perform the following operations on a VCR For RX 7030VBK RX 7032VSL After pressing VCR or VCR CONTROL you can perform the following operations on a VCR 1 9 0 Select the TV channels on a VCR gt Start playing REW Rewind a tape PF Fast wind a tape Stop playing or recording Pause playing To resume press REC PAUSE Enter recording pause by pressing this button To start recording again press this button then CH Change the TV channels on the VCR Note You can use either VCR 1 for RX 8030VBK or VCR for RX 7030VBK RX 7032VSL or the control button CONTROL
169. ntrol 18 8 For RX 8030VBK CC CONVERTER button and lamp 21 For RX 7030VBK RX 7032VSL BASS BOOST button and lamp 22 9 SUBWOOFER OUT ON OFF button 19 10 PHONES jack 19 Display Window 2 ANALOG DIGITAL AUTO 96 24 MULTI Display Window DUAL indicator 35 ANALOG indicator 20 DIGITAL AUTO indicator 20 96 24 indicator 35 MULTI indicator 40 DO PRO LOGIC indicator 34 DO PRO LOGIC II indicator 35 TUNED indicator 23 STEREO indicator 23 24 NEO 6 indicator 35 AUTO MUTING indicator 24 OOOO eoeeemeo 20 21 22 amp GG GG o OQ TUNED STEREO AUTO MUTING ONETOUCH OPERATION SLEEP JO PRO LOGICI NEO 6 VIRTUAL SB MIDNIGHT MODE DIGITAL EQ DSP 3D PHONIC HEADPHONE SPEAKERS 1 2 BASS BOOST EX ES button 37 INPUT ANALOG button 20 INPUT ATT button 20 MIDNIGHT MODE button 20 INPUT DIGITAL button 20 TUNER CONTROL buttons e FM AM TUNING A buttons 23 e FM AM PRESET A buttons 23 24 FM MODE button 24 MEMORY button 23 Only for RX 8030VBK VIDEO input jacks 13 DIGITAL optical terminal S VIDEO jack VIDEO jack AUDIO L R jacks SETTING button 27 QUICK SPEAKER SETUP button 25 MULTI JOG control 25 27 31 PUSH SET button 25 27 31 EX
170. nufacturer s code using buttons 1 9 and 0 See the list on page 49 to find the code 4 Release TV The following buttons can be used for operating a TV TV OM Turn on and off a TV TV VOL Adjust the volume TV VIDEO Set the input mode either TV or VIDEO After pressing TV DBS you can perform the following operations on a TV CH Change the channels 1 10 0 0 100 10 Select the channels The 10 0 button will function as the ENTER button if your TV requires pressing ENTER after selecting a channel number Notes All the functions listed above may not be assigned to the buttons for some TVs e f you cannot change the channels of some TVs by pressing 10 keys press CH for changing the channels 5 Try to operate your TV by pressing TV cl When your TV turns on or off you have entered the correct code If there are more than one code listed for your brand of TV try each one until the correct one is entered To change the transmittable signals for operating a CATV converter or DBS tuner 1 2 Press and hold CATV DBS cori Press CATV DBS CONTROL For RX 8030VBK CALL appears on the display window of the remote control Enter a manufacturer s code using buttons 1 9 and 0 See the list on page 49 to find the code Release CATV DBS crt The following buttons can be used for operating a CATV converter and DBS tuner CATV DBS l Turn on and off a CA
171. ocedure on page 31 The DIGITAL EQ indicator goes off from the display Notes e When Analog Direct is in use Digital Equalization patterns are not Adjusting the Speaker Output Levels You can adjust the speaker output levels The test tone comes out of each speaker except subwoofer to check the output level balance when using the Surround mode Once you have made an adjustment it is memorized for each source m Adjustable speakers You can adjust the following speakers output levels within the range of 10 dB to 10 dB 0 dB is the initial setting available The Digital Equalization affects the front speaker sounds only You can also use the remote control for equalization adjustment Press SOUND The 10 keys are activated for sound adjustments Press DIGITAL EQ Equalization repeatedly to select the center frequency you want to adjust Each time you press the button the center frequency with its current level appear on the display Press LEVEL or repeatedly to adjust the level of the center frequency The DIGITAL EQ indicator lights up on the display The frequency level changes from 8 dB to 8 dB in 2 dB steps Repeat steps 2 and 3 to adjust the other center frequency 32 SUBWFR LVL Select to adjust the subwoofer output level FRONTLLVL Select to adjust the left front speaker output level FRONTRLVL Select to adjust the right front speak
172. of existing theaters and halls Thanks to the high performance DSP Digital Signal Processor and high capacity memory you can enjoy multi channel surround sound by playing 2 channel or multi channel software according to the speaker setting Multi channel headphone virtual surround sound 3D HEADPHONE Mode The built in headphone virtual surround system is compatible with Multi channel software like Dolby Digital DTS Surround etc Thanks to the new signal processing algorithms used by the high performance DSP you can enjoy a natural surround sound through the headphones COMPU LINK AV COMPU LINK remote control systems These COMPU LINK remote control systems allow you to operate other JVC s audio video components from this receiver Power sources When unplugging the receiver from the wall outlet always pull the plug not the AC power cord Do not handle the AC power cord with wet hands If you are not going to operate the receiver for an extended period of time unplug the AC power cord from the wall outlet Ventilation High power amplifiers built in this receiver will generate heat inside the cabinet For safety observe the following carefully Make sure there is good ventilation around the receiver Poor ventilation could overheat and damage the receiver Do not block the ventilation openings or holes If the ventilation openings or holes are blocked by a newspaper or cloth etc the heat may not be abl
173. onents using the DIGITAL IN terminals set the following correctly if necessary Set the digital input DIGITAL IN terminal setting correctly For details see Setting the Digital Input Terminals on page 29 Select the digital input mode correctly For details see Selecting the Analog or Digital Input Mode on page 19 Digital input terminals You can connect any digital components having coaxial or optical digital output terminal Digital coaxial cable not supplied between digital coaxial terminals Digital optical cable not supplied DIGITAL IN When the component has a digital T coaxial output terminal connect it to the DIGITAL 1 DVD terminal using a digital coaxial cable not supplied DIGITAL 1 DVD When the component has a digital D optical output terminal connect it to the BAS Gal DIGITAL 2 CD DIGITAL 3 TV or uu DIGITAL 4 CDR terminal using a ie digital optical cable not supplied DIGITAL 3 TV Before connecting a digital e optical cable unplug the protective plug SS a DIGITAL 4 CDR p A Notes e When shipped from the factory the DIGITAL IN terminals have been set for use with the following components DIGITAL 1 coaxial For DVD player DIGITAL 2 optical For CD player DIGITAL 3 optical For digital TV broadcast tuner DIGITAL 4 optical For CD recorder e When
174. onnected components will turn on automatically depending on which component has been previously selected When you turn off the receiver the connected components will turn off standby Synchronized Hecording Synchronized recording means the cassette deck or MD recorder starts recording as soon as a CD begins playing To use synchronized recording follow these steps 1 Put a tape in the cassette deck or an MD in the MD recorder and a disc in the CD player 2 Press the record 6 button and the pause H button on the cassette deck or MD recorder at the same time This puts the cassette deck or MD recorder into recording pause If you do not press the record 6 button and pause II button at the same time the synchronized recording feature will not operate 3 Press the play gt button on the CD player The source changes on the receiver and as soon as play starts the cassette deck or MD recorder starts recording When the play ends the cassette deck or MD recorder enters recording pause and stops about 4 seconds later Notes During synchronized recording the selected source cannot be changed If the power of any component is shut off during synchronized recording the COMPU LINK remote control system may not operate properly In this case you must start again from the beginning 41 B AV COMPU LINK Remote Control System The AV COMPU LINK remote control system allows you to ope
175. ont speakers 2 nitial setting for center surround and surround back speakers Notes Keep the following comments in mind as reference when adjusting If the size of the cone speaker unit built in your speaker is larger than 12 cm 4 3 inches select LARGE and if it is smaller than 12 cm 4 inches select SMALL e f you have selected NO for the subwoofer setting you can only select LARGE for the front speakers e f you have selected SMALL for the front speakers you cannot select LARGE for the center surround and surround back speakers f you have selected SMALL for the surround speakers you cannot select LARGE for the surround back speakers e f you have selected for the surround speakers the surround back speakers are fixed to NONE m Surround back speakers quantity SBACK OUT Select the number of the surround back speakers connected I1SPK Select this to use 1 surround back speaker 2SPK Select this to use 2 surround back speakers Note If you have selected NONE for the surround back speakers see above this setting is not available 27 Setting the Speaker Distance The distance from your listening point to the speakers is another important element to obtain the best possible sound of the Surround and DSP modes Set the distance from your listening point to the speakers By referring to the speaker distance setting
176. onventional surround formats NEO 6MUSIC Suitable for playing music software The front channel signals bypass the decoder resulting in no loss of sound quality and the surround signals transmitted through the other speakers expand the sound field naturally What is Dual Mono Dual Mono can be easily understood when you think of the bilingual broadcast or the MTS Multichannel Television Sound used for TV programs however the Dual Mono format is not identical with those analog formats This format is now adopted in Dolby Digital DTS and so on It allows two independent channels called main channel and sub channel to be recorded separately When Dual Mono signal is detected the DUAL indicator lights up You can select either channel you want to listen to see page 29 When using the Surround mode the sounds come out of the avtivated speakers which the Surround mode requires If the surround speakers and center speaker are set to NONE in the speaker setting JVC s original 3D PHONIC processing which has been developed to create the surround effect through the front speakers only is used The 3D PHONIC indicator lights up on the display Manufactured under license from Dolby Laboratories Dolby Pro Logic and the double D symbol are trademarks of Dolby Laboratories 2 DTS DTS ES Extended Surround and Neo 6 are trademarks of Digital Theater Systems Inc 35
177. or RX 7030VBK RX 7032VSL When changing the source name from TAPE to CDR 1 Press TAPE CDR Make sure TAPE appears on the display 2 Press and hold TAPE CDR until ASSGN CDR appears on the display To change the source name to TAPE repeat the same procedure above Note Without changing the source name you can still use the connectedcomponents However there may be some inconvenience e For RX 8030VBK TAPE or TV will appear on the display when you select the MD recorder or DBS tuner You cannot use the digital input see pages 19 and 20 for the MD recorder You cannot use the COMPU LINK remote control system see pages 41 to operate the MD recorder e For RX 7030VBK RX 7032VSL TAPE or TV will appear on the display when you select the CD recorder or DBS tuner You cannot use the digital input see pages 19 and 20 for the CD recorder 21 The following basic operations are possible only using the remote control Reinforcing the Bass Muting the Sound P Using the Sleep 2 Changing Timer the Display Brightness Reinforcing the Bass You can boost the bass level Once you have made adjustment it is memorized for each source 1 Press SOUND The 10 keys are activated for sound adjustments d Press BASS BOOST to turn on Bass Boost The BASS BOOST indicator lights up Each time you press the button Bass Boost t
178. or RX 8030VBK DVD initial setting MD CDR TV or DBS or CD For RX 7030VBK RX 7032VSL DVD initial setting CD TV or DBS or CDR m Digital optical terminals DGTL IN OPTICAL For RX 8030VBK Set the components connected to the digital optical terminals DIGITAL IN 2 4 As you rotate MULTI JOG the digital optical input terminals are set to used for following digital components When DIGITAL IN 1 DGTL IN COAX is set to DVD AOD 3 V 0r DBS AICDR 2 CD 3 TV or DBS 4 MD Il 2 CD 3 MD 4 CDR zc 2 MD 3 TV or DBS 4 CDR Il back to the beginning When DIGITAL IN 1 DGTL IN COAX is set to CD 2 DVD 3 TV or DBS 4 CDR I 2 DVD 3 TV or DBS 4 MD 2 DVD 3 MD 4 CDR 2 MD 3 TV or DBS 4 CDR back to the beginning When DIGITAL IN 1 DGTL IN COAX is set to TV or DBS 2 CD 3 DVD 4 CDR I 2 CD 3 DVD 4 MD I 2 CD 3 MD 4 CDR a 2 MD 3 DVD 4 CDR I back to the beginning When DIGITAL IN 1 DGTL IN COAX is set to CDR 2 CD 3 TV or DBS 4 DVD I 2 CD 3 TV or DBS 4 MD 2 CD 3 MD 4 DVD gt 2 MD 3 TV or DBS 4 DVD back to the beginning When DIGITAL IN 1 DGTL IN COAX is set to MD 2 3 TV or DBS 4 CDR 2 3 TV or DBS 4 DVD 2 3 DVD 4 CDR 2 DVD 3 TV or DBS 4 CDR b
179. order gt Start playing lt Return to the beginning of the current or previous track gt gt Skip to the beginning of the next track Stop playing or recording Pause playing To resume press 1 10 0 10 Select a track number directly For track number 5 press 5 For track number 15 press 10 then 5 For track number 20 press 10 then 10 0 For track number 30 press 10 10 then 10 0 Enter recording pause by pressing this button To start recording again press this button then gt REC PAUSE Cassette deck For RX 8030VBK After pressing TAPE MD or selecting TAPE by pressing CONTROL repeatedly you can perform the following operations on a cassette deck For RX 7030VBK RX 7032VSL After pressing TAPE CDR or TAPE CDR CONTROL you can perform the following operations on a cassette deck gt Start playing REW Fast wind the tape from right to left FE Fast wind the tape from left to right Stop playing or recording Pause playing To resume press REC PAUSE Enter recording pause by pressing this button To start recording again press this button then gt MD recorder RX 8030V After pressing TAPE MD or selecting TAPE by pressing CONTROL repeatedly you can perform the following operations on a MD recorder gt Start playing aa Return to the beginning of the current or previous track gt gt Skip to the beginning o
180. oss of sound quality and the surround signals transmitted through the other speakers expand the sound field naturally What is Dual Mono Dual Mono can be easily understood when you think of the bilingual broadcast or the MTS Multichannel Television Sound used for TV programs however the Dual Mono format is not identical with those analog formats This format is now adopted in Dolby Digital DTS and so on It allows two independent channels called main channel and sub channel to be recorded separately When Dual Mono signal is detected the DUAL indicator lights up You can select either channel you want to listen to see page 29 When using the Surround mode the sounds come out of the avtivated speakers which the Surround mode requires If the surround speakers and center speaker are set to NONE in the speaker setting JVC s original 3D PHONIC processing which has been developed to create the surround effect through the front speakers only is used The 3D PHONIC indicator lights up on the display Manufactured under license from Dolby Laboratories Dolby Pro Logic and the double D symbol are trademarks of Dolby Laboratories 2 DTS DTS ES Extended Surround and Neo 6 are trademarks of Digital Theater Systems Inc 35 e Surround Modes Applicable to the Various Software Available Surround modes vary depending on the speaker settings and the incoming signals Th
181. ot solve contact your JVC s service center PROBLEM The display does not light up POSSIBLE CAUSE The power cord is not plugged in SOLUTION Plug the power cord into an AC outlet No sound from speakers Speaker signal cables are not connected Check speaker wiring and reconnect if necessary See pages 9 to 11 The SPEAKERS ON OFF 1 and SPEAKERS ON OFF 2 buttons are not set correctly Press SPEAKERS ON OFF 1 and SPEAKERS ON OFF 2 correctly See page 19 An incorrect source is selected Select the correct source Muting is activated Press MUTING to cancel the mute See page 22 An incorrect input mode analog or digital is selected Select the correct input mode analog or digital See page 19 Sound from one speaker only Speaker signal cables are not connected properly Check speaker wiring and reconnect if necessary See pages 9 to 11 Continuous hiss or buzzing during FM reception Incoming signal is too weak Connect an outdoor FM antenna or contact your dealer See page 8 The station is too far away Select a new station An incorrect antenna is used Check with your dealer to be sure you have the correct antenna Noise is heard during FM AM reception Antennas are not connected properly Check connections See page 8 Ignition noise from automobiles Move the antenna farther from automobile traffic Howl
182. ource name to CDR which will be shown on the display when it is selected as the source See page 21 for details MD recorder To listen to the sound after connection press TAPE MD for RX 8030VBK or TAPE CDR for RX 7030VBK RX 7032VSL For RX 8030VBK You can connect either an MD recorder or a cassette deck to the TAPE MD jacks When connecting a cassette deck see page 12 RX 8030VBK MD recorder To audio output GR ON f e aftu MD n ese e uu Note When connecting an MD recorder to the TAPE MD jacks change the source name to MD which will be shown on the display when it is selected as the source See page 21 for details For RX 7030VBK RX 7032VSL You can connect an MD recorder to the TAPE CDR jacks if they are not used for connecting another component such as a cassette deck or CD recorder When connecting an MD recorder to the TAPE CDR jacks see page 12 Though your MD recorder is one of JVC products with the COMPU LINK remote control system you cannot use the COMPU LINK remote control system to operate the connected MD recorder Video component connections Use the cables with RCA pin plugs not supplied Connect the white plug to the audio left jack the red plug to the audio right jack and the yellow plug to the video jack If your video components have S video Y C separation and or component video Y Pr terminals connect them using an S video
183. ps flashing The station is assigned to the selected channel number 5 Repeat steps 1 to 4 until you store all the stations you want To erase a stored preset station Storing a new station on a used number erases the previously stored one 23 To tune in a preset station Selecting the FM Reception Mode On the front panel uve uve E c o c c c c es Ld E When an FM stereo broadcast is hard to receive or noisy you can change the FM reception mode while receiving an FM broadcast You can store the FM reception mode for each preset station see 1 Press FM or AM to select the band The last received station of the selected band is tuned in page 23 2 Press FM AM PRESET A or Y until you find the While listening to an FM station press FM MODE channel you want Each time you press the button the FM reception mode alternates Pressing FM AM PRESET A increases the number between AUTOMUTING and MODE MONO Pressing FM AM PRESET decreases the number TUNED STEREO AUTOMUTING voume COC Cn COCOCOCO CO CO CD CD C eo C e CO Gn SPEAKERS 1 c voume 1 Press FM AM to select the band The last received station of the se
184. r 39 ll Using the DVD MULTI Playback Mode This receiver provides the DVD MULTI playback mode for reproducing the analog discrete output mode of the DVD player C p de Activating the DVD MULTI Playback Mode onnection diagram JVC mm d M RX 8030VBK e 9 E7 lt x EEBEES 0 RX 7030VBK RX 7032VSL 1 Press DVD MULTI so that DVD MULTT appears on the display The MULTI indicator also lights up DVD a T FRONT 1 PP SPEAKERS 1 VOLUME Note When you select DVD MULTI as the source to play the Surround and DSP modes are canceled and the SURROUND and DSP buttons do not work DVD player P N a dius 2 Select the analog discrete output mode on the DVD player and start playing a DVD Refer also to the manual supplied with the DVD player You can adjust Digital Equalization patterns and speaker output TEES levels See Adjusting the Equalization Patterns on page 32 for E Fl JG details A T mponent vi component video output Notes B To subwoofer output C To center channel audio output Midnight Mode is not available for DVD MULTI playback mode see D To S video output page 20
185. r There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again Ex When adjusting the subwoofer level to 3 1 Press ADJUST The last selected item appears on the display SPEAKERS 1 voume 21 2 Turn MULTI JOG until an item you want appears on the display n this example select SUBWFR LVL For available items see the list to the left SPEAKERS 1 voume I 21 3 Press in MULTI JOG PUSH SET The current setting or level for the selected item appears on the display SPEAKERS 1 voume I 21 4 Turn MULTI JOG to select a setting you want or to make an adjustment as you like voume I 21 5 Press EXIT 6 Repeat steps 2 to 5 to set other items if necessary 7 Press EXIT The source indication resumes on the display 31 Adjusting the Equalization Patterns You can adjust the equalization patterns to your preference Once you have made adjustment it is memorized for each source Equalization adjustment DIGITAL EQ You can adjust five frequency 63 Hz 250 Hz 1 kHz 4 kHz 16 kHz within the range of 8 dB to 8 dB 0 dB is the initial setting in 2 dB steps When adjustment is made the DIGITAL EQ indicator lights up on the display To flat the equalization pattern set all the frequency to 0 dB in step 4 of Basic Pr
186. r Connection RIGHT LEFT RIGHT LEFT LEFT RIGHT CENTER SURROUND BACK SPEAKERS SURROUND PEAKERS SPEAKER FRONT SPEAKERS IMPORTANT When using only one After connecting the speakers set the speaker surround back speaker installation information properly You can use Quick connect the cord to the Speaker Setup for easy speaker installation information RIGHT terminal and the Surround speakers setting see page 25 the LEFT O Right Left To obtain the best possible Surround DSP effect see Setting the Speakers on page 27 Connecting the subwoofer speaker You can enhance the bass by connecting subwoofer Connect the input jack of a powered subwoofer to the rear panel using a cable with RCA pin plugs not supplied RX 8030VBK RX 7030VBK PREOUT SINGLE USE See Instruction Manual For Connection SUBWOOFER SUBWOOFER RIGHT LEFT SURROUND BACK SPEAKERS SI Placing speakers Front speakers and center speaker Cc Place these speakers position of the mid range speaker units at the same ue 0 C8 height from the floor 3071 30 s Subwoofer 7 Point these speakers aiming at the listener s ears Surround and surround back speakers Fa 90 90 N Place these speakers at a position which is 1 meter higher tha
187. r 15 press 10 then 5 For track number 20 press 10 then 10 0 For track number 30 press 10 10 then 10 0 Example Selecting disc number 4 track number 12 and starting playback For RX 8030VBK 1 Press CONTROL repeatedly until CDDSC appears on the display window then press 4 2 Press CD then press 10 2 For RX 7030VBK RX 7032VSL 1 Press CD DISC then press 4 2 Press CD then press 10 2 If your CD changer is of 200 disc loading capability except for XL MC100 and XL MC301 you can do the following operations using the 10 keys after pressing CD 1 Select a disc number 2 Then select a track number always enter two digits 3 Start playback Examples Selecting disc number 3 track number 2 and starting playback Press 3 then 0 2 then gt Selecting disc number 10 track number 5 and starting playback Press 1 0 then 0 5 then gt Selecting disc number 105 track number 12 and starting playback Press 1 0 5 then 1 2 then gt Turntable RX 8030V ONLY After pressing PHONO you can perform the mms following operations on a turntable gt Start playing Stop playing CD recorder For RX 8030VBK After pressing CDR or selecting CDR by pressing CONTROL repeatedly you can perform the following operations on a CD recorder For RX 7030VBK RX 7032VSL After pressing TAPE CDR or TAPE CDR CONTROL you can perform the following operations on a CD rec
188. r any one of the Surround DSP mode which activates the center and or surround speaker s you can use only one set of the speakers CAUTION Be sure to turn down the volume Before connecting or putting on headphones as its high volume can damage both the headphones and your hearing Before turning on speakers again as its high volume may come out of the speakers You can cancel the subwoofer sound even though you have connected a subwoofer and have set SUB WOOFER to YES see page 27 This is useful when enjoying surround sound at night o o eco 000000 o o oo Press SUBWOOFER OUT ON OFF to cancel the subwoofer sound output Each time you press the button subwoofer sound output is deactivated SUBWFR OFF and activated SUBWFR ON alternately When subwoofer sound output is activated subwoofer output level can be adjusted using the remote control 1 Press SOUND 2 Press SUBWOOFER 3 Press LEVEL or to adjust the output level 10 dB to 10 dB Note You cannot deactivate the subwoofer sound output when you set SMALL for the front speakers on the Speaker size setting see page 27 or Quick Speaker Setup see page 25 Selecting the Analog or Digital Input Mode When you have connected digital source components using the digital terminals see page 16 change the input mode for these components
189. r future reference Model No Serial No Purchase data Name of dealer Authorized Service Centers BT 51002 5 0301 QUALITY JVC SERVICE HOW TO LOCATE YOUR JVC SERVICE CENTER TOLL FREE 1 800 537 5722 http www jvc com Dear Customer In order to receive the most satisfaction from your purchase please read the instruction booklet before operating the unit In the event that repairs are necessary please call 1 800 537 5722 for your nearest authorized servicer or visit our website at www JVC com Remember to retain your Bill of Sale for Warranty Service Do not service the television yourself Caution To prevent electrical shock do not open the cabinet There are no user serviceable parts inside Please refer to qualified service personnel for repairs Accessories To purchase accessories for your JVC product please call toll free 1 800 882 2345 or on the web at www JVC com L g EN 2003 VICTOR COMPANY OF JAPAN LIMITED VICTOR COMPANY OF JAPAN LIMITED 2 I T Oo oo oo lt lt aA 2 T e m N lt o H3AI3O3H 1IOHLNOO OACIA OIGNV 0203NHMMDWJEIN 4 JVC MM AUDIO VIDEO CONTROL RECEIVER AMPLI TUNER DE COMMANDE AUDIO VIDEO RX 8030VBK RX 030VBK Francais AV 4 CAMDI I TEATS F BEVIN 4 V AAADI II IAG We wIEVIE V BEEF WEN 11 Remote illl DO Posy DIGITAL EX K For RX 8030VBK SM co
190. r manufacturer s code using buttons 1 9 and 0 See the list on page 49 to find the code 4 Release VCR 1 O lor VCR o The following buttons can be used for operating a VCR VCR 1 OVI For RX 8030VBK Turn on and off a VCR VCR OM For RX 7030VBK RX 7032VSL Turn on and off a VCR After pressing VCR 1 or VCR you can perform the following operations on a VCR CH Change the TV channels on a VCR 1 10 0 0 100 10 Select the TV channels The 10 0 button will function as the ENTER button if your VCR requires pressing ENTER after selecting a channel number gt Start playback REW Rewind a tape FF Fast wind a tape Stop playing or recording Pause playing To resume press REC PAUSE Enter recording pause by pressing this button To start recording again press this button then gt 5 Try to operate your VCR by pressing VCR 1 or VCR When your VCR turns on or off you have entered the correct code If there are more than one code listed for your brand of VCR try each one until the correct one is entered 48 To change the transmittable signals for operating another manufacturer s DVD player 1 Press and hold AUDIO cori 2 Press DVD For RX 8030VBK CALL appears on the display window of the remote control 3 Enter a manufacturer s code using buttons 1 9 and 0 See the list on page 49 to find the code 4 Release AUDIO cri After pressin
191. rate JVC s video components TV VCR and DVD player through the receiver This receiver is equipped with the AV COMPU LINK III which adds a function to the previous version in order to operate JVC s video components through the video components terminals To use this remote control system connect the video components you want to operate following the diagrams below and the procedure on the next page CONNECTIONS 1 AV COMPU LINK Connection DVD player TV CONPULIN CAUTION You can only connect to the TV 7 with the AV COMPU LINK EX or rss AV COMPU LINK III jack yos B E comet tne DO NOT connect to the TV with a 7 po AV COMPU LINK RECEIVER E AMP jack E COMPU LINK am IMPORTANT The AV COMPU LINK remote control system cannot control the DBS tuner For RX 8030VBK Connect the VCR to the VCR 1 jacks Video components connected to the VIDEO and VCR 2 jacks on the receiver cannot be controlled with the AV COMPU LINK remote control system Notes When connecting the receiver and a TV with the AV COMPU LINK EX terminal by using a component video cable you cannot use automatic selection of TV s input mode see page 43 When connecting only the VCR or DVD player to this receiver connect it directly to the receiver using cables with the monaural mini plugs CONNECTIONS 2 Video Cable Connection This receiver is equipped with three types of the video termi
192. ress the button the band alternates between FM and AM 2 Press TUNING UP or TUNING DOWN repeatedly until you find the frequency you want Pressing TUNING UP increases the frequency Pressing TUNING DOWN decreases the frequency Jvc z CQ 00 EZ 28 E i Once a station is assigned to a channel number the station can be quickly tuned in You can preset up to 30 FM and 15 AM stations To store the preset stations Before you start remember There is a time limit in doing the following steps If the setting is canceled before you finish start from step 2 again On the front panel ONLY 1 Tune in the station you want to preset see Tuning in to Stations Manually on the left f you want to store the FM reception mode for this station select the FM reception mode you want See Selecting the FM Reception Mode on page 24 2 Press MEMORY TUNED STEREO SPEAKERS 1 voume 21 The channel number position starts flashing on the display for about 10 seconds 3 Press FM AM PRESET A or V to select a channel number while the channel number position is flashing SPEAKERS 1 voume 21 4 Press MEMORY again while the selected channel number is flashing on the display The selected channel number stops flashing The station is assigned to the
193. roduced audio format such as Dolby Digital EX Dolby Pro Logic II DTS ES DTS Neo 6 and DTS 96 24 This unit is also compatible with Dual Mono signals recorded in Dolby Digital and DTS discs DAP Digital Acoustic Processor Sound field simulation technology allows precise ambience recreation of existing theaters and halls Thanks to the high performance DSP Digital Signal Processor and high capacity memory you can enjoy multi channel surround sound by playing 2 channel or multi channel software according to the speaker setting Multi channel headphone virtual surround sound 3D HEADPHONE Mode The built in headphone virtual surround system is compatible with Multi channel software like Dolby Digital DTS Surround etc Thanks to the new signal processing algorithms used by the high performance DSP you can enjoy a natural surround sound through the headphones COMPU LINK AV COMPU LINK remote control systems These COMPU LINK remote control systems allow you to operate other JVC s audio video components from this receiver Power sources When unplugging the receiver from the wall outlet always pull the plug not the AC power cord Do not handle the AC power cord with wet hands f you are not going to operate the receiver for an extended period of time unplug the AC power cord from the wall outlet Ventilation High power amplifiers built in this receiver will generate heat inside the cabinet For safety ob
194. rrect antenna Noise is heard during FM AM reception Antennas are not connected properly Check connections See page 8 Ignition noise from automobiles Move the antenna farther from automobile traffic Howling during record playing A ground cable from the turntable is not connected to the screw marked on the rear Connect the cable to the screw marked 7 on the rear Your turntable is too close to the speakers Move the speakers away from the turntable No sound effect such as Surround mode DSP mode and Digital Equalization Analog Direct is turned on Turn off Analog Direct See page 21 DVD MULTI is selected as the source Select the source other than DVD MULTI See page 40 EX ES 7 1 channel reproduction cannot be done for Dolby Digital EX or DTS ES software Software or setting is not for Dolby Digital EX or DTS ES software Play back software bearing the mark 9024 or Eres Set EX ES setting to ON See page 37 OVERLOAD starts flashing on the display Speakers are overloaded because of high volume 1 Press O I STANDBY ON on the front panel to turn off the receiver 2 Stop the playback source 3 Turn on the receiver again and adjust the volume Speakers are overloaded because of short circuit of speaker terminals Press 0 1 STANDBY ON on the front panel to turn off the receiver then check the speaker
195. rround speaker Back to the beginning 3 Select a speaker you want to adjust To select the left front speaker press FRONT L To select the center speaker press CENTER To select the right front speaker press FRONT R To select the right surround speaker press SURR R To select the surround back speaker press SURR BACK To select the left surround speaker press SURR L 4 Press LEVEL or LEVEL to adjust the speaker output level 10 dB to 10 dB 5 Repeat steps 3 and 4 to adjust the other speaker s output levels 6 Press TEST again to stop the test tone Adjusting the Surround and DSP Modes You can adjust the preference Sound Parameters for the Surround and DSP sound parameters to your When center speaker is set to NONE CTR TONE CNTR WIDTH and CNTR GAIN are not available m Adjustable parameters You can adjust the following parameters For Surround DAP and All Channel Stereo modes when the center speaker is connected This setting memorized CTR TONE is common to all surround modes and is separately for DSP modes Adjust the center tone As the number increases the dialogue becomes clearer so that the human voices change from soft to sharp Normally select 3 initial setting Adjustable range 1 to 5 For DAP modes Once you have made an adjustment it is memorized for each DAP mode EFFECT Adjust the DAP effect level
196. rument Hamlin Regal 01 02 03 04 05 Jerrold 06 07 08 09 10 11 12 13 14 Oak 15 16 17 Panasonic 18 19 20 Pioneer 21 22 Scientific Atlanta 23 24 25 Tocom 26 Zenith 27 28 For VCR Manufacturer JVC Aiwa Bell amp Howell Blaupunkt CGM Emerson 08 10 11 12 64 65 Fisher 03 14 15 16 17 01 18 19 20 Goldstar Goodmans Grundig Hitachi 18 23 24 25 66 Loewe 07 21 Magnavox 04 19 24 Mitsubishi 30 31 32 33 34 35 NEC 26 27 Nokia Nordmende Orion Panasonic 19 24 39 40 Philips 04 19 21 24 41 42 Phonola 21 RCA Proscan 04 18 19 23 24 43 44 45 SABA 38 46 Samsung 45 47 59 61 62 63 Sanyo 03 48 49 Sharp 37 50 Siemens 03 51 Sony 52 53 54 Telefunken 55 60 Toshiba 43 44 Zenith 56 57 For DVD player Manufacturer JVC Denon 01 Panasonic 03 Philips 13 Pioneer 04 05 06 RCA 07 Samsung 08 Sony 09 Toshiba 10 Yamaha nitial setting Manufacturers codes are subject to change without notice If they are changed this remote control cannot operate the equipment 49 RT Troubleshooting Use this chart to help you solve daily operational problems If there is any problem you cann
197. s To change the shut off time press SLEEP repeatedly To cancel the Sleep Timer Press SLEEP repeatedly until SLEEP Omin appears on the display The SLEEP indicator goes off Turning off the power also cancels the Sleep Timer Recording a source For analog to analog recording You can record any analog playback source onto the recording components connected to the audio output jacks on the rear of this unit at the same time For digital to digital recording You can record the currently selected digital input source through the receiver to a digital recording device connected to the DIGITAL OUT terminal Notes Analog to digital and digital to analog recordings are not possible The output volume level Midnight Mode see page 20 Bass Boost see the left column Digital Equalization see page 32 Surround modes and DSP modes see pages 34 to 39 cannot affect the recording Basic adjustment auto memory This receiver memorizes sound settings for each source when you turn off the power when you change the source and when you assign the source name see page 21 When you change the source the memorized settings for the newly selected source are automatically recalled The following can be stored for each source Analog digital input mode see pages 19 and 20 nput attenuator mode see page 20 Analog Direct see page 21 Digital Equalization see page 32 Speaker ch
198. s follows DIGITAL AUTO OO DIGITAL gt HALL 1 gt HALL 2 LIVE CLUB DANCE CLUB gt PAVILION ALL STEREO THEATER 1 THEATER2 MONO FILM Back to the beginning When surround speakers are set to NONE you cannot select ALL STEREO When multi channel signals come in you cannot select MONO FILM Note When the surround speakers are deactivated the 3D PHONIC processing is applied to the DSP modes the 3D PHONIC indicator Sound reproduced from All Channel Stereo mode also lights up To cancel the DSP modes Press SURROUND DSP OFF or SURR DSP OFF on the remote control SURR OFF appears on display Monaural When the front speakers are deactivated HEADPHONE will In order to reproduce a more acoustic sound field in your listening appear room while viewing monaural sound video software analog and 2 channel digital signals you can use this mode The surround effect will be added and the sound localization of actor s words will be improved This mode cannot be used for multi channel digital signals When MONO FILM is used sounds come out of all the connected and activated speakers f incoming signals change from 2 channel digital signal to another digital signal type MONO FILM is canceled and an appropriate Surround mode is activated 39 ll Using the DVD MULTI Playback Mode This recei
199. s to enjoy the surround effect One surround back speaker or one pair of surround back speakers to enjoy to produce more effective surround effect One center speaker to emphasize human voices One subwoofer to enhance the bass CAUTION Use only the speakers of the SPEAKER IMPEDANCE indicated by the speaker terminals When connecting to both of the FRONT SPEAKERS and terminals use speakers with an impedance of 16 Q to 32 When connecting to either the FRONT SPEAKERS or terminals use speakers with an impedance of 8 Q to 16 Basic connecting procedure 1 Twist and remove the insulation at 7 the end of each speaker signal cable not supplied 2 Open the speaker terminal RX 7030VBK RX 7032VSL For FRONT SPEAKERS 2 terminals 3 Insert the speaker signal cable For each speaker except for a subwoofer connect the and terminals on the rear panel to the and terminals marked on the speakers Speaker layout Ideal speaker layout varies depending on the conditions of your listening room The diagram below is a recommended typical example Subwoofer Left front speaker s Center speaker Right front speaker s L C R M a Left surround Right surround speaker LS speaker RS Surround back speakers LSB RSB Rear terminals of RX 8030VBK are used for explanation Front speakers 1 Front speakers 2 Surround back spea
200. selected channel number 5 Repeat steps 1 to 4 until you store all the stations you want To erase a stored preset station Storing a new station on a used number erases the previously stored one 23 To tune in preset station Selecting the FM Reception Mode On the front panel o o eo ooo o o 00 0 8 ll Q 0 o o o o Ec ct IF 000 When an FM stereo broadcast is hard to receive or noisy you can change the FM reception mode while receiving an FM broadcast You can store the FM reception mode for each preset station see page 23 1 Press FM or AM to select the band The last received station of the selected band is tuned in 2 Press FM AM PRESET A or Y until you find the While listening to an FM station press FM MODE channel you want Each time you press the button the FM reception mode alternates Pressing FM AM PRESET A increases the number between AUTOMUTING and MODE MONO Pressing FM AM PRESET decreases the number TUNED STEREO AUTOMUTING From the remote control mor eons voume IZ 21 DOO CO CO C2 CO Co Co co e a oe cl SPEAKERS 1 CO voume IZ 1 Press FM AM to select the band
201. serve the following carefully Make sure there is good ventilation around the receiver Poor ventilation could overheat and damage the receiver Do not block the ventilation openings or holes If the ventilation openings or holes are blocked by a newspaper or cloth etc the heat may not be able to get out Others Should any metallic object or liquid fall onto the unit unplug the unit and consult your dealer before operating any further Do not expose this apparatus to rain moisture dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus Do not disassemble the unit since there are no user serviceable parts inside If anything goes wrong unplug the AC power cord and consult your JVC dealer Bi Parts ldentification Remote Control RX 8030VBK AN CONTROL RECEIVER CATV DBS VCR1 TV AUDIO 2 Con Con DVD MULTI DVD cD AM FM Res TAPE MD TV DBS VIDEO PHONO ANALOGDIGITAL CO CO CO re 13 SURROUND DSP SURR DSP ANALOG 4 CO CO Ce Gee 4 BASSBOOST FRONT L gt FRONT R oe eae ae ING MIDNIGHT SURRE 17119 6 T 7 P 8 9 kDIGITALEQ SURR BACK 205 cy 4 0 v caves ee m e SDE EN
202. soon the receiver turns off again into standby mode The receiver is overloaded because of a high voltage Press I STANDBY ON on the front panel to turn off the receiver After unplugging the AC power cord consult your dealer Remote control does not work There is an obstruction between the remote sensor on the receiver and the remote control Remove the obstruction Batteries are weak Replace batteries See page 8 Remote control does not work as you intend 50 An incorrect remote control operation mode is selected Select the correct remote control operation mode See pages 44 to 49 Specifications RX 8030VBK Amplifier Output Power At Stereo operation Front ch 130 W per channel min RMS driven into 8 Q 20 Hz to 20 kHz with no more than 0 08 total harmonic distortion At Surround operation Front ch 130 W per channel min RMS driven into 8 Q at 1 kHz with no more than 0 8 total harmonic distortion Center ch 130 W min RMS driven into 8 Q at 1 kHz with no more than 0 8 total harmonic distortion Surround ch 130 W per channel min RMS driven into 8 Q at 1 kHz with no more than 0 8 total harmonic distortion Surround Back ch 130 W min RMS driven into 8 Q at 1 kHz with no more than 0 846 total harmonic distortion Audio Audio Input Sensitivity Impedance 1 kHz PHONO IN MM 2 5 mV 47 kQ DVD IN VCR 1 IN VCR 2 IN TV SOUND DBS IN VIDEO IN 200 mV 47
203. stment is made the DIGITAL EQ indicator lights m Adjustable speakers You can adjust the following speakers output levels within the up on the display range of 10 dB to 10 dB 0 dB is the initial setting To flat the equalization pattern set all the frequency to 0 dB SUBWER LVL Select to adjust the subwoofer output level in step 4 of Basic Procedure on page 31 The DIGITAL EQ indicator goes off from the display FRONT L LVL Select to adjust the left front speaker output level Notes FRONT Select to adjust the right front speaker When Analog Direct is in use Digital Equalization patterns are not output level available mE CENTER LVL Select to adjust the center speaker output The Digital Equalization affects the front speaker sounds only level SURRLLVL Select to adjust the left surround speaker output level You can also use the remote control for equalization adjustment SURRRLVL Select to adjust the right surround speaker output level OD CO SBACK LVL Select to adjust the surround back speaker C T output level als A Notes 9 7 Z e If you have selected NO or NONE for a speaker see page 27 the output level for the corresponding speaker is not O A O adjustable C gt The center speaker and left right surround speakers output V o levels are adjustable for DVD MULTI playback mode even though
204. supplied See CONNECTIONS 1 on the previous page 3 Connect the audio input output jacks on VCR DVD player TV and this receiver using the cables with RCA pin plugs See pages 14 and 15 4 Connect the video input output jacks on VCR DVD player TV and this receiver using the cables with RCA pin plugs S video plug or component video plugs See CONNECTIONS 2 on the previous page 5 Plug the AC power cords of the components and the receiver into the AC outlets 6 When turning on the TV for the first time after the AV COMPU LINK connection turn the TV volume to the minimum using the TV volume control on the TV 7 Turn on the connected components first then turn on this receiver When turning on the VCR use the remote control supplied with this receiver The AV COMPU LINK remote control system allows you to use the five basic functions listed below Remote Control of the TV DVD player and VCR Using This Remote Control See page 46 for details Aim the remote control directly at the remote sensor on each target component One Touch Video Play Simply by inserting a video cassette without its safety tab into the VCR you can enjoy the video playback without setting other switches manually The receiver automatically turns on and changes the source to VCR 1 for RX 8030VBK or VCR for RX 7030VBK The TV automatically turns on and changes the input mode to the appropriate posit
205. system automatically changes the TV s input mode to the TV tuner This function does not work when you connect this receiver and the TV with the AV COMPU LINK EX terminal using a component video cable In this case reconnect the TV referring to case 1 or case 2 on page 42 Automatic Power On Off The TV VCR and DVD player turn on and off along with the receiver When you turn on the receiver If the previously selected source is VCR 1 for RX 8030VBK or VCR for RX 7030VBK the TV and VCR will turn on automatically If the previously selected source is DVD or DVD MULTI the TV and DVD player will turn on automatically If the previously selected source is any video source other than the above only the TV will turn on automatically When you turn off the receiver the TV VCR and the DVD player will turn off Note If you turn off the receiver while recording on the VCR the VCR will not turn off but continue recording 43 Operating JVC s Audio Video Components You can operate JVC s audio and video components with this receiver s remote control since control signals for JVC s components are preset in the remote control Operating Audio Components IMPORTANT To operate JVC s audio components using the supplied remote control You need to connect JVC s audio components through the COMPU LINK SYNCHRO jacks see page 41 in addition to the connections using cables with RC
206. t MID NIGHT 1 or MID NIGHT 2 appears on the display The MIDNIGHT MODE indicator also lights up I 000 MID NIGHT 1 Select when you want to reduce the dynamic range a little No indicator lights up when the receiver cannot recognize the digital signal format of the incoming signals When playing software encoded with the Dolby Digital or DTS the following symptoms may occur Sound does not come out at the beginning of playback Noise comes out while searching for or skipping chapters or tracks DGTL D D or DGTL DTS while DGTL AUTO still remains on the display As you press INPUT DIGITAL the input mode changes as follows In this case press INPUT DIGITAL repeatedly to select DIGITAL AUTO R LFE RS Sud pma SEF voume Z 21 SPEAKERS 1 DGTL AUTO DGTL D D Digital Dolby Dita DGTL DTS When DGTL DGTL DTS is selected the AUTO indicator goes off and the corresponding digital signal format indicator lights up on the display If the incoming signal does not match the selected digital signal format the frame of the selected indicator will flash Note When you turn off the power or select another source DGTL D D and DGTL DTS settings are canceled and the digital input mode
207. t 3 0 m 10 f DGTL IN COAX Select the component connected to digital coaxial terminal 29 S mH on DGTL IN OPTICAL Select the components connected to 3 0 m 10 ft digital optical terminals 29 3 0 m 10 ft VIDEO IN DVD Select the type of video terminal Distance used for the DVD player 30 2 7 m 9 ft VIDEO IN DBS Select the type of video terminal 2 7 m 9 ft used for the DBS tuner 30 2 4 m 8 ft ONETOUCH OPE Store the volume level for each 21m 7 ft source 30 2 1 m 7 ft 1 8 m 6 ft Notes Distance These items be set using Quick Speaker Setup This setting is only for RX 8030VBK 2 4 m 8 ft For RX 7030VBK it is automatically set according to your DGTL IN 2 4 m 8 ft COAX setting 2 1 m 7 ft 1 5 m 5 ft 1 5 m 5 ft 1 2 m 4 ft 26 Basic Procedure i C c oo 000000 oa IF 000 s Before you start remember There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again Ex When setting One Touch Operation to ON 1 Press SETTING The last selected item appears on the display SPEAKERS 1 voume IZ I 2 Turn MULTI JOG until an item you want appears on the display In this example select ONE TOUCH OPE For available items see the list Basic Setting Items on page 26
208. t the volume level while Analog Direct is in use Once you have made adjustment it is memorized for each analog o o o o mis LL Source ooo Press ANALOG DIRECT so that DIRECT appears the display The lamp on the button also lights up Each time you press the button Analog Direct turns on and off Notes When digital input mode is in use Analog Direct is not available e Turning on Surround or DSP mode cancels Analog Direct and previously selected sound adjustments are recalled e f Analog Direct is in use Midnight Mode is temporarily canceled Turning on Analog Direct cancels Input Attenuator 20 and CC Converter for RX 8030VBK below RX 8030v ONLY Making Sounds Natural JVC s CC Compensative Compression Converter eliminates jitter and ripples achieving a drastic reduction in digital distortion by processing the digital music data in 24 bit quantization and by expanding the sampling frequency to 128 kHz for fs 32 kHz signals 176 4 kHz for fs 44 1 kHz signals 192 kHz for fs 48 kHz signals By using CC Converter you can obtain a natural sound field from both digital and analog sources Jvc c o c c o o oo
209. ted item appears on the display voume Z 21 4 Turn MULTI JOG until a setting you want appears on the display ONETOUCH OPERATION SPEAKERS 1 voume Z 21 5 Press EXIT 6 Repeat steps 2 to 5 to set other items if necessary 7 Press EXIT The source indication resumes on the display shows the initial setting in the following tables Setting the Speakers To obtain the best possible surround effect from the Surround and DSP modes register the setting about the speaker arrangement after all connections are completed If you have used Quick Speaker Setup on page 25 this setting is not required m Subwoofer setting SUB VVOOFEH Select whether you have connected a subwoofer or not YES Select when a subwoofer is connected NO Select when no subwoofer is used Note If you have selected NO for the subwoofer you cannot use the SUBWOOFER OUT ON OFF button on the front panel Speaker size FHONT SPEAKER CNTR SPEAKER SURR_ SPEAKER SBACK SPEAKER Select the size for each connected speaker Select when the speaker size is relatively large SMALL Select when the speaker size is relatively small NONE Select this when you have not connected a speaker Not selectable for the front speakers nitial setting for front speakers 2 nitial setting for center surround and surround back speakers Notes
210. ter connection press CDR for RX 8030VBK or TAPE CDR for RX 7030VBK For RX 8030VBK RX 8030VBK RX 7030VBK CD player RX 8030VBK CD recorder To audio output To audio output Cassette deck aq TOA To listen to the sound after connection press TAPE MD for RX T CUR 8030VBK or TAPE CDR for RX 7030VBK PLAY TOXO OS For RX 8030VBK REND You can connect either a cassette deck or an MD recorder to the TAPE MD jacks When connecting an MD recorder see page 13 For RX 7030VBK You can connect either a CD recorder or a cassette deck to the TAPE CDR jacks When connecting a cassette deck to the TAPE CDR jacks see the left column RX 8030VBK Cassette deck To audio input m HEN RX 7030VBK CD recorder To audio output For RX 7030VBK Em e Onn lt p PLAY You can connect either a cassette deck or a CD recorder to the TAPE CDR jacks When connecting an CD recorder to the TAPE Rp CDR jacks see the right column 1 Note For RX 7030VBK When connecting CD recorder to the TAPE CDR jacks change the source to CDR which will be shown the display when it is selected as the source See page 21 for details RX 7030VBK Cassette deck 12 MD recorder To listen to the sound after connection press TAPE MD for RX 8030VBK or TAPE CDR for RX 7030VBK For RX 8030VBK
211. ter speaker size 27 The size of connected speakers SURR SPEAKER Register your surround speaker size 27 L R RS SB SBACK SPEAKER Register your surround back NONE NONE speaker size 27 NONE NONE SBACK OUT Register the number of the NONE NONE connected surround back speakers 27 NONE NONE DIST UNIT Select the measuring unit for the SMALL NONE speaker distance 28 SMALL NONE FRONT DISTANCE Register the distance from you front speakers to your listening point 28 NONE CNTR DISTANCE Register the distance from you center SMALL NONE speaker to your listening point 28 SMALL SMALL SURR DISTANCE Register the distance from you SMALL SMALL surround speakers to your listening SMALL SMALL point 28 SMALL SBACK DISTANCE Register the distance from you EE surround back speaker s to your This setting is applied to the both speakers listening point 28 S WFR OUTPUT Select sounds emitted from the Room size and the speaker distance subwoofer 28 According to the selected room size speaker distance for each CROSS OVER Select the cutoff frequency to the activated speaker is set as follows subwoofer 28 LFE ATTENUATE Attenuate the bass LFE sounds 29 Speaker Distance 3 0 m 10 ft DUAL MONO Select the Dual Mono sound channel 29 3 0 m 10 f
212. th the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by the manufacturer for compliance could void the users authority to opratethe equipment For Canada pour Le Canada THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS AS SET OUT IN THE INTERFERENCE CAUSING EQUIPMENT STANDARD ENTITLED DIGITAL APPARATUS ICES 003 OF THE DEPARTMENT OF COMMUNICATIONS CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS NUMERIQUES DE CLASSE B PRESCRITES DANS LA NORME SUR LE MATERIEL BROUILLEUR APPAREILS NUMERIQUES NMB 003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS For Canada pour le Canada CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FU
213. the Bass socere sereisas entree enda 22 Mnuting the terret tr Reb ipee nt 22 Changing the Display Brightness ees 22 Using the Sleep TIMET eret peterent ec races 22 Receiving Radio Broadcasts 23 Tuning in to Stations Manually Using Preset oerte rrt ror aene Reel o Selecting the FM Reception Mode sss 24 This mark indicates that ONLY the remote control CAN be used for the operation explained This mark indicates that the remote control CANNOT be used for the operation explained Use the buttons on the front panel Basic 25 Setting the Speakers Configuration sss 25 Basic Setting Iteris eere ox tae ted 26 Basic PrOcedute iens Rte 27 Setting the Speakers tette tret 27 Setting the Speaker Distance esee 28 Setting the Bass Sounds 2 irren ttt 28 Selecting main or sub channel DUAL 29 Setting the Digital Input Terminals 29 Setting the Component Video 30 Memorizing the Volume Level for Each Source 30 Adjusting Sound s 31 Basic Setting Items onam i ecce ees 31 Basic Pfocedute ore ntn ac i eremo rer ivit Adjusting the Equalization
214. the display For details see page 21 For RX 7030VBK When connecting an CD recorder to the TAPE CDR jacks and a DBS tuner to the TV SOUND DBS jacks change the source names shown on the display For details see page 21 17 Speaker and signal indicators on the display By checking the following indicators you can easily confirm which speakers you are activating and which signals are coming into this receiver Speaker indicators Signal indicators L c R L CR LFE s 85 LS S RS 168 SB What speaker indicators light depends on the speaker setting for details see Setting the Speakers on page 27 The frames of L LS RS and SB light up when the corresponding speakers are set to LARGE or SMALL and when the speaker is required for the Surround DSP mode currently selected e When SUB WOOFER is set to YES SUBWFR lights up see page 27 All three frames on the row of SB are not used at the same time When SBACK OUT is set to 2SPK the left and the right ones are used When it is set to 1SPK the middle one is used see page 27 The signal indicators light up to show the incoming signals L e When digital input is selected Lights up when the left channel signal comes in When analog input is selected Always lights up R When digital input is selected Lights up when t
215. the following operations on a tuner 1 10 0 10 Select a preset channel number directly For channel number 5 press 5 For channel number 15 press 10 then 5 For channel number 20 press 10 then 10 0 TUNING UP DOWN Tune into stations FM MODE Change the FM reception mode Sound control section Amplifier You can always perform the following operations SURROUND Turn on and select Surround modes DSP Turn on and select DSP modes SURR DSP OFF Turn off Surround and DSP modes After pressing SOUND you can perform the following operations FRONTeL then LEVEL Adjust the left front speaker output level Adjust the right front speaker output level Adjust the center speaker output level Adjust the left surround speaker output level Adjust the right surround speaker output level Adjust the surround back speaker output level SUBWOOFER then LEVEL Adjust the subwoofer output level FRONT R then LEVEL CENTER then LEVEL SURR L then LEVEL SURReR then LEVEL SURR BACK DIGITAL EQ then LEVEL Select the sound frequency bands and adjust its level TEST Turn on or off test tone output BASS BOOST Turn on or off Bass Boost Note After adjusting sounds press the corresponding source selection button to operate your target source by using the 10 keys otherwise the 10 keys cannot be used for operating your target source CD player After pressing
216. the sound adjustments such as speaker output level adjustments see page 32 Digital Equalization see page 32 Surround and DSP modes see pages 34 to 39 Bass Boost see page 22 and Midnight Mode see page 20 You can only adjust the volume level while Analog Direct is in use Once you have made adjustment it is memorized for each analog source 000 Ld Press ANALOG DIRECT so that A DIRECT appears on the display The lamp on the button also lights up Each time you press the button Analog Direct turns on and off Notes When digital input mode is in use Analog Direct is not available e Turning on Surround or DSP mode cancels Analog Direct and previously selected sound adjustments are recalled e f Analog Direct is in use Midnight Mode is temporarily canceled Turning on Analog Direct cancels Input Attenuator page 20 and CC Converter for RX 8030VBK below RX 8030V ONLY Making Sounds Natural JVC s CC Compensative Compression Converter eliminates jitter and ripples achieving a drastic reduction in digital distortion by processing the digital music data in 24 bit quantization and by expanding the sampling frequency to 128 kHz for fs 32 kHz signals 176 4 kHz for fs 44 1 kHz signals 192 kHz for fs 48 kHz signals By using CC Converter you can obtain a natural sound field from both digital and
217. this unit automatically sets the delay time of the sound through each speaker so that sounds through all the speakers can reach you at the same time If you have used Quick Speaker Setup on page 25 this setting is not required m Measuring unit DIST UNIT Select which measuring unit you use meter Select to set the distance in meters feet Select to set the distance in feet Speaker distance FRONT DISTANCE CNTR DISTANCE SURR DISTANCE SBACK DISTANCE Set the distance from the listening point within the range of 0 3 m 1 ft to 9 0 m 30 ft in 0 3 m 1 ft intervals When shipped from the factory distance for each speaker is set to 3 0 m 10 ft Notes You cannot set the speaker distance for the speakers you have selected NONE see page 27 This setting is not valid for the DVD MULTI playback mode Ex In the above case set the speaker distance as follows Front speakers 3 0 m 10 ft Center speakers 3 0 m 10 ft Surround speakers 2 7 m 9 ft Surround back speakers 2 4 m 8 ft 28 Setting the Bass Sounds You can adjust subwoofer and bass sounds precisely according to your preference m Subwoofer output S WFR OUTPUT You can select the type of the signal which can be transmitted through the subwoofer In other words you can determine whether or not the bass elements of the front speaker channels are transmitted through the subwoofer regardless of the front
218. torted while playing back software When you use the digital input terminals register which components encoded with Dolby Digital or DTS set the LFE level to you have connected to the digital input terminals eliminate distortion m Digital coaxial terminal DGTL IN COAX Set the component connected to the digital coaxial terminal Select one of the following OdB Normally select this DIGITAL IN 1 10dB Select when the bass sound is distorted For RX 8030VBK DVD initial setting MD CDR TV or DBS or CD e For RX 7030VBK DVD initial setting CD TV or DBS Selecting main or sub channel DUAL MONO or CDR Select the playback sounds channel m Digital optical terminals DGTL IN OPTICAL MAIN pun to m m m den For RX 8030VBK t 61 7 1 t P M Perm A Set the components connected to the digital optical terminals DIGITAL IN 2 4 SUB Selectto play back the sub channel Ch2 2 mE Signal indicator R lights up while playing back this e As you rotate MULTI JOG the digital optical input terminals channel are set to used for following digital components ALL Selectto play back both the main and sub channels When DIGITAL IN I DGTL IN COAX is set to DVD Chl Ch2 2 C D 3 TV or DBS 4 CDR Signal indicators L and R light up while playing 2 CD 3 TV or DBS 4 MD back these channels 2 CD 3 MD 4 CDR 2
219. ug the cord When unplugging the cord always grasp the plug so as not to damage the cord a Basic Operations The following operations are commonly used when you play any sound sources Operations hereafter will be explained using the buttons on the front panel You can also use the buttons on the remote control for the same functions if they have the same and similar names marks Daily Operational Procedure Turn on the power See Turning On the Power below Select the source See Selecting the Source to Play to the right Adjust the volume See Adjusting the Volume on page 18 Select the surround or DSP modes See Activating the Surround Modes page 37 and Activating the DSP Modes page 39 Turning On the Power s O c Inm El Ll Press 0 1 STANDBY ON or AUDIO on the remote control The STANDBY lamp goes off The name of the current source and Surround DSP mode appear on the display Current source name and Surround DSP mode appear Current volume level appears To turn off the power into standby mode press 0 1 STANDBY ON or AUDIO 0 1 on the remote control again The STANDBY lamp lights up Note A small amount of power is consumed in
220. ugh all the speakers can reach you at the same time If you have used Quick Speaker Setup on page 25 this setting is not required m Measuring unit DIST UNIT Select which measuring unit you use meter Select to set the distance in meters feet Select to set the distance in feet Speaker distance FRONT DISTANCE CNTR DISTANCE SURR DISTANCE SBACK DISTANCE Set the distance from the listening point within the range of 0 3 m 1 ft to 9 0 m 30 ft in 0 3 m 1 ft intervals When shipped from the factory distance for each speaker is set to 3 0 m 10 ft Notes You cannot set the speaker distance for the speakers you have selected NONE see page 27 This setting is not valid for the DVD MULTI playback mode Ex In the above case set the speaker distance as follows Front speakers 3 0 m 10 ft Center speakers 3 0 m 10 ft Surround speakers 2 7 m 9 ft Surround back speakers 2 4 m 8 ft 28 Setting the Bass Sounds You can adjust subwoofer and bass sounds precisely according to your preference m Subwoofer output S WFR OUTPUT You can select the type of the signal which can be transmitted through the subwoofer In other words you can determine whether or not the bass elements of the front speaker channels are transmitted through the subwoofer regardless of the front speaker size setting either SMALL or Select one of the following
221. ur JVC Product please contact our Customer Relations Department WHAT IS NOT COVERED This limited warranty provided by JVC does not cover 1 Products which have been subject to abuse accident alteration modification tampering negligence misuse faulty installation lack of reasonable care or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service or if affixed to any attachment not provided with the products or if the model number or serial number has been altered tampered with defaced or removed Initial installation and installation and removal for repair Operational adjustments covered in the Owner s Manual normal maintenance video and audio head cleaning Damage that occurs in shipment due to act of God and cosmetic damage Signal reception problems and failures due to line power surge Video Pick up Tubes CCD Image Sensor Cartridge Stylus Needle are covered for 90 days from the date of purchase Batteries except that Rechargeable Batteries are covered for 90 days from the date of purchase MOS S RON There are no express warranties except as listed above THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT INCONVENIENCE LOSS OR ANY OTHER DAMAGES WHETHER DIRECT INCIDENTAL OR CONSEQUENTIAL INCLUDING
222. urce name and Surround DSP mode appear SPEAKERS 1 voueli Current volume level appears To turn off the power into standby mode press 0 1 STANDBY ON or AUDIO I on the remote control again The STANDBY lamp lights up Note A small amount of power is consumed in standby mode To turn off the power completely unplug the AC power cord 000 I Press one of the source selection buttons The selected source name and the previously selected Surround DSP mode also appear on the display Selected source name and current Surround DSP mode appear TUNED STEREO AUTOMUTING ONETOUCHOPERATION SLEEP DOPROLOGICI NEO 6 VIRTUAL SB MIDNIGHT MODE DIGITAL EQ DSP 3D PHONIC HEADPHONE SPEAKERS 1 2 BASSBOOST weur 11 1 vo uve It 11 8030 o o o a a o o o vert I SOUND TAPEMD On the unit The lamp on the selected source lights up ex when DVD is selected as the source DVDMULTI DVD CD FM AM 29 OC VCR1 VCR2 TAPE MD Ge TVDBS VIDEO PHONO On the remote For RX 7030VBK RX 7032VSL DVDMULTI DVD VCR TV SOUND DBS TAPE CDR FM AM
223. urns on BOOST ON and off BOOST OFF alternately For RX 7030VBK RX 7032VSL RX Z032V You can use the BASS BOOST button on the front panel p When the Bass Boost is activated the lamp on the button lights up Each time you press the button Bass Boost turns on and off Notes e This function affects only the sounds from the front speakers center speaker and subwoofer When Analog Direct is in use see page 21 the Bass Boost is canceled temporarily Muting the Sound Press MUTING to mute the sound through all speakers and headphones connected MUTING appears on the display and the volume turns off the VOLUME level indicator goes off To restore the sound press MUTING again Turning MASTER VOLUME on the front panel or pressing VOLUME on the remote control also restores the sound Changing the Display Brightness You can dim the display Press DIMMER Each time you press the button the brightness level of the display change as follows Dimmer Much dimmer Canceled LL Normal display 22 Using the Sleep Timer Using the Sleep Timer you can fall asleep while listening to music When the shut off time comes the receiver turns off automatically Press SLEEP repeatedly The SLEEP indicator lights up on the display and the shut off time changes in 10 minutes intervals lier as 0 To check or change the time remaining until the shut off time
224. v Tem For RX 8030VBK INS TRUC TIONS For Customer Use Enter below the Model No and Serial No which are located either on the rear MANUEL D INSTRUCTIONS bottom or side of the cabinet Retain this information for future reference Model No Serial No LVT1007 002A C Warnings Cautions and Others Mises en garde precautions et indications diverses CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION To reduce the risk of electrical shocks fire etc 1 Do not remove screws covers or cabinet 2 Do not
225. ven into 8 Q at 1 kHz with no more than 0 8 total harmonic distortion Surround Back ch 110 W min RMS driven into 8 Q at 1 kHz with no more than 0 8 total harmonic distortion Audio Audio Input Sensitivity Impedance 1 kHz DVD IN VCR IN TV SOUND DBS IN CD IN TAPE CDR IN Audio Input DIGITAL IN Coaxial DIGITAL 1 DVD 0 5 V p p 75 Q Optical DIGITAL 2 CD DIGITAL 3 TV DIGITAL 4 CDR 21 dBm to 15 dBm 660 nm 30 nm Corresponding to Linear PCM Dolby Digital and DTS Digital Surround with sampling frequency 32 kHz 44 1 kHz 48 kHz 200 mV 47 kQ 200 mV 47 Audio Output Level SUBWOOFER OUT 1V Recording Output Level VCR OUT TAPE CDR OUT 200 mV Digital output Optical DIGITAL OUT Signal wave length 660 nm Output level 21 dBm to 15 dBm Signal to Noise Ratio 66 IHF 78 IHF DVD IN VCR IN TV SOUND DBS IN CD IN TAPE CDR IN Frequency Response 8 Q DVD IN VCR IN TV SOUND DBS IN 20 Hz to 100 kHz 1 dB 3 dB 20 Hz to 100 kHz 1 dB 3 dB 87 dB 80 dB 87 dB 80 dB CD IN TAPE CDR IN Equalization 5 bands 63 Hz 250 Hz 1 kHz 4 kHz 16 kHz 8 dB Bass boost 6 dB 1 0 dB at 100 Hz 52 Video Video Input Sensitivity Impedance Composite video DVD IN VCR IN TV SOUND DBS IN 1 V p p 75 S video DVD IN VCR IN SOUND DBS IN Y luminance C chrominance burst Component video DVD IN DBS IN Y luminance 1 75 Q
226. ver provides the DVD MULTI playback mode for reproducing the analog discrete output mode of the DVD player C Om Activating the DVD MULTI Playback Mode onnection diagram L co x CE C At B INA RX 8030VBK RX 7030VBK GOGE fue AE E 1 Press DVD MULTI so that DVD MULTI SUBWOOFER CENTER RIGHT LEFT VIDEO S VIDEO vt is indicator also lights up CGO nyp T gt FRONT SURR REAR R E Note When you select DVD MULTI as the source to play the Surround and DSP modes are canceled and the SURROUND and DSP buttons do not work DVD player p N 2 Select the analog discrete output mode on the T 9000 i i DVD player and start playing a DVD Al 7 Refer also to the manual supplied with the DVD player LN You can adjust Digital Equalization patterns and speaker output DI mom il levels See Adjusting the Equalization Patterns on page 32 for E Fl details A To component video output B To subwoofer output To center channel audio output Midnight Mode is not available for DVD MULTI playback mode see D To S video output s 20 T i To composite video output Bir
227. you better sound quality ll Analog Connections Audio component connections Use the cables with RCA pin plugs not supplied Connect the white plug to the audio left jack and the red plug to the audio right jack RX 8030VBK Left front speaker Right front speaker If your audio components have a COMPU LINK jack See also page 41 for detailed information about the connection and the COMPU LINK remote control system CAUTION If you connect a sound enhancing device such as a graphic equalizer between the source components and this receiver the sound output through this receiver may be distorted Power amplifier RX 8030V ONLY Turntable a Power amplifier To listen to the sound after connection press PHONO E RX 8030VBK Turntable If a ground cable is provided for your turntable connect the cable to the CE S7 screw marked 2 on the rear Power amplifier Semmes LES To audio output Left surround speaker Right surround speaker Note This connection is for the turntable with an MM moving magnet type cartridge Any turntables incorporating a small output cartridge such as an MC moving coil type must be connected to this receiver through a commercial head amplifier or step up transformer Direct connection may result in insufficient volume Surround back speakers Left Right Note If you connect one surround back speaker con

JVC RX-8030V Receiver

Contents

Download Pdf Manuals

Related Search

Related Contents