Siemens SpeedStream 2614 Router (ss2614) - Quick
Contents
1. Power on both the DSL modem and the SpeedStream router Connect to the SpeedStream router s configuration interface by entering HTTP 192 168 254 254 and click Enter On the SpeedStream Router Status page check the Internet connection status section for the field labeled Cable DSL Ensure that the status says Connected e If it says Connected you have successfully obtained an IP Address from your DSL service provider and may proceed with using the router and Internet service as desired e If it says Disconnected continue to the next step Troubleshooting Ensure that the DSL modem is securely connected to the router and the modem is powered on and functioning properly Ensure that the Username and Password entered are accurate verify with your DSL service provider if necessary Upgrade the firmware on the SpeedStream router to the latest version available Connection Configuration for Home cable modem service users 1 2 NoNe Obtain your exact HOST NAME from Home or your Windows Network Control Panel Connect to the SpeedStream router s configuration interface by entering HTTP 192 168 254 254 and press Enter You will see the SpeedStream Router Status screen Select Simple Setup from the left side menu and choose WAN from the expanded menu Select Dynamic IPAddress and click Enter Enter the HOST NAME you were provided by Home and click Enter Wait approximately 10 seconds then click the Status li2. Internet connection type For detailed procedures covering the most common broadband Internet access scenarios refer to the procedures provided on the back side of this guide If additional configuration is desired select the Advanced Setup link from the left side menu to configure items such as firewall parameters DMZ host virtual servers and special applications support for multi player online games The most common scenarios are described on the back of this guide Step 3 Print Server Set up optional Printer Port Driver Installation 1 Ensure that the printer is connected to the parallel port on the router and both the printer and router are powered on 2 Insert the supplied CD ROM into your CD ROM drive If the setup program does not start automatically run SETUP from the root folder on the CD ROM 3 Consult the User Guide on CD ROM for step by step installation and configuration instructions specific to your operating system 4 Repeat the procedure for each PC that will share the printer
3. Tips and Troubleshooting Connection Configuration for DSL service users Most DSL service providers supply users with a dynamic IP address but require a valid username and password to be entered first This method is known as PPP over Ethernet PPPoE Note If your service provider currently requires you to use separate PPPoE client software discontinue use of this software and complete the following procedure to configure the SpeedStream router to negotiate the PPPoE logon to your service provider s network 10 14 Connect to the SpeedStream router s configuration interface by entering HTTP 192 168 254 254 and press Enter You will see the SpeedStream Router Status screen Select Simple Setup from the left side menu and choose WAN from the expanded menu Select PPPoE and click Enter Enter the Username and Password exactly as provided by your DSL service provider leave the Service Name field blank and click Enter Wait approximately 10 seconds then click the Status link in the left side menu On the SpeedStream Router Status page check the Internet connection status section for the field labeled Cable DSL Ensure that the status says Connected e If it says Connected you have successfully obtained an IP Address from your DSL service provider and may proceed with using the router and Internet service as desired e If it says Disconnected continue to the next step Power off both the DSL modem and the SpeedStream router
4. es and trademarks are held by their respective companies Efficient Networks reserves the right to make changes to product specifications at any time without notice SIEMENS 007 0096 002 Quick Start Guide Before you begin Package Contents Your package includes the following SpeedStream 2614 4 Port DSL Cable Router AC Power Adapter SIEMENS TENDED SIEMENS Safety and Certifications Spendsiroam O Safety and Quick Start Guide Documentation Extended Warranty Certifications Printer Port Driver CD and Registration Card Information This guide covers only the most common situations Please refer to the full User s Guide on the CD ROM if your network uses any of the following existing router existing DHCP server or PC s using fixed static IP addresses Requirements Broadband Modem PC s with the TCP IP protocol installed Cat 5 Ethernet cables with RJ 45 connectors Step 4 Hardware Installation 1 Ensure that the SpeedStream 2614 is powered OFF before commencing with installation Leave your DSL Cable modem connected to its wall socket phone line or cable outlet 2 Use Cat 5 Ethernet cable s to connect one or both of the following PC s to one of the LAN ports on the SpeedStream router OR A hub switch to one of the LAN ports on the router 3 Connect your DSL Cable modem to the WAN port on the SpeedStream 2614 using the Ethernet cable supplied with your DSL Cable modem If no cable was suppl
5. ied with your modem use a straight through Ethernet cable Note An ISDN TA or dial up modem may be connected to the SpeedStream 2614 Router as an alternate method of Internet access Please refer to the User s Guide on CD for directions on using configuring this type of connection 4 Connect the power adapter to the SpeedStream 2614 Use only the power adapter provided 5 optional If you intend to use the SpeedStream router s print server functionality connect the parallel cable of the printer to the printer port on the router before powering on the router 6 Power ON the SpeedStream 2614 Front View DSL Cable modem Step 2 Internet Connection Configuration If your Internet Service Provider assigns your IP address dynamically your PC should already be configured properly for the SpeedStream 2614 to act as a plug and play device and does not require additional configuration 1 Perform TCP IP Setup for each PC as described in the PC Setup section on the back of this guide Remember to restart each PC when finished Start your web browser In the Address box enter the following HTTP 192 168 254 254 Press Enter You will be prompted for a Password The default Password is admin When the password is entered correctly you will see the SpeedStream Router Status screen IPUN Select Simple Setup from the left side menu and follow the prompts to change the password set the Time Zone and choose the appropriate
6. ktop select Properties 2 Select the TCP IP gt Ethernet Adapter entry 3 Ensure Obtain an IP Address Automatically is selected The DHCP server in the SpeedStream router will provide an IP address for the PC 4 Click OK twice then restart your PC even if no changes were made Internet Access L Select Start Menu gt Settings gt Control Panel gt Internet Options 2 Select the Connections tab and click the Setup button oH Select want to set up my Internet connection manually or want to connect through a Local Area Network LAN and click Next 4 Select connect through a Local Area Network LAN and click Next Uncheck all boxes on the Local Area Network Internet Configuration screen and click Next 6 Follow the remaining prompts until the wizard has finished o Technical Support for North America is available 24 hours a day 7 days a week by phone email or online Phone 1 877 823 6722 Email support speedstream com Online http www support speedstream com SIEMENS For more information regarding SpeedStream products visit www speedstream com Efficient Networks Inc A Siemens Company 4849 Alpha Road Dallas TX 75244 2001 Efficient Networks Inc All rights reserved Efficient Networks its logos Live a Broadband Life and SpeedStream are registered and unregistered trademarks of Efficient Networks Inc Siemens and the Siemens logo are registered trademarks of Siemens AG Germany All other brand nam
7. nk in the left side menu On the SpeedStream Router Status page check the Internet connection status section for the field labeled Cable DSL Ensure that the status says Connected e If it says Connected you have successfully obtained an IP Address from the Home service and may proceed with using the router and Internet service as desired e If it says Disconnected continue to the next step 8 Select Simple Setup from the left side menu and choose WAN from the expanded menu 9 Select Dynamic IPAddress and click Enter 10 Click the Clone MAC Address button 11 Click Enter 12 Wait approximately 10 seconds then click the Status link in the left side menu 13 On the SpeedStream Router Status page check the Internet connection status section for the field labeled Cable DSL Ensure that the status says Connected e If it says Connected you have successfully obtained an IP Address from the Home service and may proceed with using the router and Internet service as desired e If it says Disconnected continue to the next step 13 Troubleshooting Ensure that the Cable modem is securely connected to the router and the modem is powered on and functioning properly Ensure that the HOST NAME entered is accurate verify with Home if necessary Upgrade the firmware on the SpeedStream router to the latest version available PC Setup Windows 95 98 98SE Me TCP IP Setup 1 Right click on the Network Neighborhood icon on your des
Download Pdf Manuals
Related Search