GE Monogram ZGG24L20BSS Grill
Contents
1. loin que possible du gril e Open the lid e Turn all knobs to OFF position e Turn gas supply on at the LP tank or shut off valve NOTE When lighting the burner for the first time or after a LP tank change allow up to 20 seconds to purge air from the lines e Push and turn control knob to LITE position immediately turn the rotary igniter knob next to the burner knob 24 Outdoor Cooking Center A Valve Panel Attachment Screws TO TEST e Apply the soap solution around the connections valve and tubing e Turn the gas supply on e Check all connections from the supply line or LP tank up to and including the manifold pipe assembly e If a leak is detected turn gas supply to off and tighten fittings Turn the gas on and check again NOTE The spark will produce a snapping sound This is normal e If the burner does not light within 4 seconds turn knobs to OFF and wait 5 minutes for the gas to dissipate before trying again e If the burner does not light after several attempts the burner can be lit with a match TO MATCH LIGHT e Strike a match and hold over the match light hole at the top left side See illustration e Push and turn the control knob to LITE c a Ll oee ne A So Gar bl FP ee ee ea H o eS eee ENS Hole DN WAIT 5 MINUTES BEFORE RELIGHTING A HOT GRILL Step 6 Adjusting the Burners Installation 24 Outdoor Cooking Cent2. Installation in Canada must be in accordance with the Standard CAN 1 b149 1 and or 2 installation code for gas burning appliances and equipment and local codes Operating pressure is 4 W C Supply pressure should be 5 to 14 W C If pressure is more than 14 W C a step down regulator is required Natural Gas 4 0 Regulator 1 2 NPT Close Nipple Adapter 1 2 NPT to 3 8 Flare Fitting 1 2 NPT Close Nipple Installer Supplied TUBING SY 3 8 FLARE A Installer Supplied Shut Off Natural Gas Supply Step 2 Install Orifices Step 3 Test for Leaks Step 4 Adjust the Burners ZX24NGB e Open the lid e Remove racks and briquette trays e Remove tie downs on burners e Remove burner knobs and 4 screws on the valve panel 2 screws behind knobs and 2 screws below valve panel e Lift the control panel up and and tilt back away from the grill e Disconnect 2 ignitor wires e Remove control panel e Pull burners back and away from the orifices e Remove original orifices one on each side e Apply threading compound to new orifices install and tighten e Re position burner inside the grill and with air shutter ends covering the orifices e Check air shutter the shutter should be open approximately 5 16 Ay WARNING TEST FOR LEAKS A complete gas tightness check must be p 8 8 performed at the installation site DES FUITES Il faut v rifier que l installation n a aucune fuite de g
3. d brancher la bouteille de gaz Il faut remiser la bouteille de gaz l ext rieur dans un endroit bien ventil Il ne faut par remiser les bouteilles de gaz proximit de l enceinte du centre de cuisson en plein air e Connect the regulator to the quick disconnect hose assembly e Check to be sure the main valve on the LP tank is completely closed To connect the tank e Insert the coupler sleeve over the tank inlet turn clockwise to tighten To disconnect the tank e Turn off the main tank valve e Grasp the coupler sleeve and turn counter clockwise Remove the inlet from the opening ELECTRICAL SUPPLY The rotisserie requires 120V 60Hz and connected to an individual properly grounded branch circuit protected by a 15 amp circuit breaker or time delay fuse The power cord on the rotisserie is equipped with a three prong grounding plug which mates with a standard three prong grounding wall receptacle to minimize the possibility of shock hazard from this appliance If the electrical service provided does not meet the above specifications it is recom mended that a licensed electrician install an approved outlet 24 Outdoor Cooking Center LP Hose Pre Attached Inlet Coupler Sleeve Main Valve L P Regulator LP operating pressure is 10 W C IMPORTANT The LP tank must be a Type 1 Acme Do not attempt to change or alter these supplied parts Do not attempt to use the regulator hose assembly with
4. GE Monogram Installation Instructions 24 Outdoor Cooking Center Model ZGG24L Contents Before you begin Read these instructions completely and carefully IMPORTANT Save these instructions for local inspector s use IMPORTANT OBSERVE ALL GOVERNING CODES AND ORDINANCES NOTE TO INSTALLER Be sure to leave these instructions with the Consumer NOTE TO CONSUMER Keep these instructions with your Use and Care Book for future reference If you received a damaged cooking center you should contact your dealer Installation of this cooking center requires basic mechanical skills Proper installation is the responsibility of the installer For Monogram local service in your area 1 800 444 1845 For Monogram service in Canada 1 888 880 3030 For Monogram Parts and Accessories call 1 800 626 2002 FOR YOUR SAFETY Do not use cooking center in a space where gasoline or other liquids having flammable vapors are stored or used CAUTION e For outdoor use only Use this cooking center only in the manner intended by the manufacturer e This outdoor cooking gas appliance Is not intended to be installed in or on recreational vehicles and or boats e Do not use the grill in an explosive atmosphere Keep the grill away from areas where gasoline or other flammable liquids and vapors are stored or being used e Observe proper clearances to combustible materials at all times e Do not use a rusty or damaged LP tank e
5. Never substitute gases natural for LP or LP for natural e This grill is factory set for liquid propane gas A natural gas conversion kit must be installed before using natural gas e When storing the grill indoors disconnect the LP tank Store the tank outdoors in a well ventilated area e Do not store additional LP tanks in or near the gas grill e Follow the guidelines on the LP tank for proper storage transport and handling e Tested in accordance with ANSI 221 58 latest edition standard for outdoor cooking gas appliances This grill Design Information MOOGI erie R A S 3 Product Dimensions amp Clearance eseese 3 PCOS SOT IGS ccirtscars odvetecanieecastesaevancntaanaatetareicneaeine 3 Advance Planning icseveaceavessoczesaesuatenaanceaannnerateaceorsiianenttes 3 Choosing the Location cssssescsessssescsesesseecseeeseeecsees 4 Tools amp Materials Required ccesscsessessesssseesseeeees 4 Step 1 Remove the Packaging cseseseeseseeseterees 4 Step 2 Provide Support Installation on a Cart wo eeeceeeeseeeeteerees 4 In the Commonwealth of Massachusetts e This product must be installed by a licensed plumber or gas fitter e When using ball type gas shut off valves they shall be T handle type e A flexible gas connector when used must not exceed 3 feet IF YOU SMELL GAS e Shut off gas to appliance e Extinguish any open flame e Open lid e f odor continues immediately call you
6. a standard 510 POL tank valve assembly DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD GROUND PRONG FROM THE POWER CORD e For built in grill installations locate the electrical outlet on the right hand side Step 4 Test for Leaks Step 5 Lighting the Grill Installation Ay WARNING TEST FOR LEAKS A complete gas tightness check must be performed at the installation site DES FUITES Il faut v rifier que l installation n a aucune fuite de gaz e Do not use the grill until all connections have been leak tested e Repeat leak test after each LP tank change e Check to be sure the main valve on the LP tank or the shut off valve is in the OFF position e Make a soap solution of one part liquid detergent and one part water The valve panel must be removed to check the valves and fittings e All control valves should be in the OFF position e Remove the knobs e Remove the 4 screws holding the valve panel to the grill 2 behind burner knobs and two below valve panel e Pull the panel outwards and unplug the wires from the back of the rotary igniters A WARNING Do not attempt to light the grill if the odor of gas is present yN PUMPS EOE T ne faut pas essayer d allumer le gril s il y a une odeur de gaz A CAUTION Keep hands and face as far away from the grill as possible when lighting A SS Pendant Vallumage il faut maintenir les mains et le visage aussi
7. alize Installation sincsncutsnvesiaxacistiundsactsvesnsenpastsaivataneasnantnes 9 Install Rotisserie esessssesssesisieiirrerrrisrsrrirrsrsrrrsrsrsrsrsrsrns 9 ZXADYSS ZXSDBSS Optional Access Doors 9 ZX24NGB Natural Gas Conversion Kit 10 Model Product Dimensions EF Clearances Accessories Advance Planning 12 Clearance to Combustibles Both Sides Design Information ZGG24L20 SS The Monogram 24 Outdoor Cooking Center is factory set for LP gas and can be converted to natural gas Order ZX24NGB Natural gas conversion kit when natural gas is available 24 3 4 24 Cutout 24 Outdoor Cooking Center 12 Min to Combustibles A Min for Lid Clearance 4 7 8 18 7 8 23 a Manifold j Pipe 3 1 2 4 For Lid Clearance when installed into a non combustible enclosure This grill may be installed on a portable grill cart or built into an enclosure Enclosures can be constructed of non combus tible masonry material or of combustible material such as wood Insulated jackets are required for installation into combustible enclosures e ZX24CTBSS grill cart e ZX24JBSS Insulated jacket for a combustible enclosure e This Monogram Outdoor Cooking Center is designed to be installed on a grill cart or into an enclosure e In a non combustible masonry enclosure the grill drops into the opening A ledge on each side is re
8. as supply lines Be sure to check on type and size of run and how deep to bury the line If the gas line is too small the grill will not function properly e Install a manual gas shut off valve in an easily accessible location e Use threading compound on non flare fittings only Do not use threading compound on the male end of the 1 2 NPT to 3 8 flare adapter e Make connections as shown e Remove quick disconnect hose assembly from manifold pipe e Leave flare fitting in the manifold pipe 1 2 to 3 8 flare e Attach installer supplied gas line to end of flare fitting on the manifold e Install regulator to gas line e Install 1 2 NPT close nipple to supplier installed shut off valve e Check to be sure the regulator arrow points in the direction of gas flow towards the grill and away from the gas supply Natural Gas Conversion Kit Materials Required not supplied e 12 ft to 15 ft max flexible hose with 3 8 flare end corrugated stainless steel preferred e Pipe wrench e Pipe threading compound e Manual gas shut off valve e Appropriate length of gas line to reach the permanent installation location with a 3 8 flare end e Flat blade screwdriver Note Optional ZX144HKY quick disconnect hose for natural gas is available to reach a 144 connection The installation of this grill must conform with local codes or in the absence of local codes with the National fuel gas code ANSI Z223 latest edition
9. az e Do not use the grill until all connections have been leak tested e Turn gas suply on e Flames should be blue and stable with some yellow tips and no excessive noise or lifting from the burner If any of these conditions exist check air shutter and burner ports for debris or spider webs To Adjust e If the flame is yellow indicating insufficient air open the air shutter to allow more air to the burner e If the flame is noisy and tends to lift away from the burner there is too much air Turn the air shutter to reduce the opening Air Shutter Natural Gas Conversion Kit Grill Box Orifice e Check to be sure that the shut off valve is in the OFF position e In a spray bottle make a soap solution of one part liquid detergent and one part water TO TEST e Spray the soap solution around the connections valve and tubing e Turn the gas supply on e Check all connections from the gas supply line up to and including the manifold e If a leak is detected turn gas supply off and tighten fittings Turn the gas on and check again Grill Box Lock Screw ll Pub No 49 8966 2 Dwg No 164D3333P193 Printed in USA N D 728 3 03 10905 Rev 2 Note While performing installations described in this book safety glasses or goggles should be worn For Monogram local service in your area call 1 800 444 1845 Note Product improvement is a continuing endeavor at General E
10. er Adjustments should not be required unless vibration during transit or variations in local gas supply make minor adjustments necessary Adjustments must be made by a qualified technician at the time of installation Extreme care should be used if adjustments are made after installation Grill Box e Turn gas supply on e Push and turn the burner control knobs to the LITE position Up to 20 seconds may be required to to purge air from the lines e Flames should be blue and stable with no yellow tips excessive noise or lifting from the burner If any of these conditions exist turn control to off and check air shutter and burner ports for debris or spider webs e Locate and loosen the lock SCrew On the face of the air shutter with a screwdriver e Turn burner to the LITE position e If the flame is yellow indicating insufficient air open the air shutter to allow more air to the burner o If the flame is noisy and tends to lift away from the burner there is too much air Turn the air shutter to reduce the opening e Once adjusted turn the burner off and TO ADJUST reverse steps to re install the valve panel e The valve panel cover must be removed to cover access the the air shutter Follow the instructions in Step 4 Test for Leaks Air Shutter Lock Screw Low setting Adjustment e When the desired setting Minor adjustments may be required due to is made replace the fluctuations in local
11. gas pressure Adjustments knob and turn burner to increase or decrease gas flow may be off necessary e Turn burner knob to LITE position e Turn the control knob to the lowest setting all the way counter clockwise e Remove the knob by pulling straight out e Insert a thin blade flat screwdriver into the valve shaft and hold 3 32 blade width recommended e Grip the shaft with pliers and turn counter clockwise to lower the flame or clockwise to increase the flame Valve Stem 7 VGN Always check the low ENON 1 faut toujours flame size for stability A burner flame v rifier la stabilit de la flamme au ralenti which is too small may go out or be extin Une flamme trop petite peut s teindre i ow a guished easily This can cause unburned facilement Ceci cause l emission de gaz gas to escape and cause a hazardous non br l ce qui est dangereux condition Finalize Installation Install Rotisserie Install Optional Access Doors ZXADYSS and ZXSDBSS For Built In Installations Only Installation e Place the small ceramic briquette tray at the rear and larger tray towards the front e Place the grill grates over the opening e Remove burner grates e Remove front large ceramic briquette tray e Place small ceramic briquette tray in the rear slots as shown e Place drip pan on the grill floor and against the briquette tray e Slide the motor down into the channel on the righ
12. he Location Tools amp Materials Required Not supplied Step 1 Remove the Packaging Step 2 Provide Support Installation On a Cart 4 Design Information 24 Outdoor Cooking Center e This cooking center is designed for outdoor use only Do not locate the grill in a building garage or other enclosed area e Ensure that fresh air ventilation is adequate or in the absence of local codes with the e Consider exposure to wind and proximity to national fuel gas code ANSI Z223 latest traffic paths edition e The minimum clearances to combustibles must be maintained at all times e Do not install a grill below overhead unprotected combustible construction e Phillips head screwdriver e Pipe wrench A CAUTION This Cooking Center e Level is extremely heavy 2 people are required e Flat blade screwdriver 3 32 blade for lifting and placing the product onto a Pliers cart or into an enclosure A PRUDENCE Ce centre de cuisson est extr mement lourd Il faut deux personnes pour le soulever et le mettre sur un chariot ou dans une enceinte e Open the box and remove packaging e Open the grill lid and remove hardware accessory carton Check contents Spit Forks Type 1 Acme 20 Lb LP Tank with Overfill Protection Device not supplied Order ZXLPY Required for Grill Cart Installation LP Regulator The Outdoor Cooking Center can be installed Allow at least 12 clearance at the back of
13. kewer e Allow at least 12 clearance on each side and rear to combustible vertical materials ZX24 BSS Insulated Jacket The insulated jacket is required for combus tible enclosures e Install left and right side pieces with bolts provided e Secure bolts inside the grill with acorn nuts e Install back panel to side panels Place the grill into the enclosure 12 Min to If Installing an Combustibles Electrical Outlet 4 Min for Lid 25 3 4 for the Rotisserie Motor Mount on Right Side 6 5 AMP Min Double Access Doors Installation in a combustible enclosure ZX24JBSS insulated jacket is required e Combustible enclosures require ZX24 BSS insulated jacket The insulated jacket must be supported by a ledge on each side e Construct the enclosure as shown Install the insulated jacket onto the grill Place the cooking center into the opening No installation hardware is required Step 3 Provide Gas F Electrical Supply Installation NOTE Skip this step if you wish to connect to natural gas supply Order ZX24NGB kit Refer to Natural Gas Conversion Instructions page 10 Ay WARNING PRODUCT STORAGE When storing LP models indoors discon nect the LP tank Store the tank outdoors in a well ventilated area Do not store spare LP tanks in or near the Outdoor Cooking Center enclosure A ATTENTION RANGEMENT DU PRODUIT Lors du rangement des mod les gas l int rieur il faut
14. lectric Therefore materials appearance and specifications are subject to change without notice Monogram We bring good things to life GE Consumer Products General Electric Company Louisville KY 40225 2003 General Electric Company
15. quired for support e An Insulated jacket is available to allow the grill to be installed in a combustible enclosure The insulated jacket must be supported by a ledge on each side e If using a backsplash or rear wall locate the electrical service for the rotisserie on the right side e Trim kit ZX24TKBSS is available to conceal the gap between cooking center and the back and sides of an enclosure Allow 12 min clearance to combustible vertical surfaces e ZX24TKBSS is available to conceal the gap between the cooking center and the enclosure e ZX24CVCG tough vinyl on the outside felt lined inside with elastic to hold the cover in place Fits grill installed on a cart or when built in e ZXSDBSS Stainless Steel Single Access Door ZXADYSS Stainless Steel Double Access Doors Optional accessories to cover the access opening under the grill in a built in installation e ZXLPY LP gas tank Clearances e Allow 4 at the rear for lid clearance e Allow at least 12 clearance at the back of the grill when exhaust is directed to a window or a surface that is difficult to clean e Allow at least 6 clearance on each side to any non combustible material located above the cooking surface for counterspace This 6 clearance will allow for placement and handling of the rotisserie motor and skewer e Allow at least 12 clearance on each side and 12 min clearance at rear to combustible vertical materials Choosing t
16. r gas supplier is for outdoor use only Check local building codes for the proper method of installation in the absence of local codes this unit should be installed in accordance with the National Fuel Gas Code No Z223 latest edition and the National Electrical Code ANSI NFPA No 70 1990 CALIFORNIA PROPOSITION 65 WARNING The burning of gas cooking fuel generates some by products that are on the list of substances which are known by the State of California to cause cancer or reproductive harm California law requires businesses to warn customers of potential exposure to such substances To minimize exposure to these substances always operate this unit according to the use and care manual ensuring you provide good ventilation when cooking with gas INSECT WARNING Spiders and insects can nest in the burners of this and any other grill and cause the gas to flow from the front of the burner This is a very dangerous condition which can cause a fire to occur behind the valve panel thereby damaging the grill and making it unsafe to operate Inspect the grill twice a year or immediately if any symptoms appear Installation Step 2 Provide Support Built In Installations oc ceeeeeesesseeeeeeees 5 Step 3 Provide Gas amp Electrical Supply 6 Step 4 Test for Leaks 0 ceeescssesesesesseeeseseseeessseeseeeees 7 Step 5 Lighting the Grill eeeseeeseseeseeeeeeeeeeeen 7 Step 6 Adjusting the Burners cece 8 Fin
17. t side e To use place pointed end of the skewer into the motor and the threaded end resting on the left side support e Screw handle onto the threaded end of the skewer ZXADYSS Double Doors The opening should be 24 1 8 wide and 18 1 4 high ZXSDBSS Single Doors The opening should be 22 wide and 20 high 24 Outdoor Cooking Center Note Ihe ceramic briquettes may move during shipping or when repositioning for rotisserie use For best cooking performance Slide briquettes on the tray so they are evenly spaced and do not block vent holes BDH A o lol lol X 1X EEE ol nun AOAI Xl KAI a Note Remove motor when not in use Store motor in dry place e Place the frame into the opening and secure with screws on all sides e Hang the doors on the hinges as shown Step 1 Install Fittings amp Regulator 10 ZX24NGB Parts supplied e Natural gas regulator e Natural gas orifices e Adapter 1 2 to 3 8 flare fitting e Two 1 2 NPT close nipple The grill and its individual shut off valve must be disconnected from the gas supply during any pressure testing of the system at test pressures in excess of 1 2 PSIG The grill must be isolated from the gas supply system by closing its individual shut off valve during any pressure testing of the system at test pressures equal to or less than 1 2 PSIG Check with local gas utility or with local codes for instructions on installing g
18. the grill when exhaust is directed to a window or on a ZX24CTBSS cart which is designed specifically for this model Follow the installa tion instructions provided with the cart to install Proceed to Gas supply Step 3 to complete the installation a surface that is difficult to clean e The installation must conform to local codes Built In Installations Built In Installations Installation e This grill may be installed into a combustible or non combustible enclosure e Combustible enclosures require the use of an insulated jacket Clearances e Allow 4 at the rear for lid clearance ZX24TKBSS Trim Kit This kit is available for non combustible enclosures The trim will conceal the gap at the rear and both sides of the opening e Secure trim to the sides and back with screws provided e Place the grill into the enclosure Ter If Installing 4 Min for Lid an Electrical Clearance i Outlet for the Rotisserie 19 Motor Mount KO on Right Side 6 5 AMP Min Opening for Double Access Doors Installation in a non combustible enclosure e In a non combustible masonry enclosure the grill drops into the opening A ledge on each side is required for support 24 Outdoor Cooking Center e Allow at least 6 clearance on each side to any non combustible material located above the cooking surface for counterspace The 6 clearance allows for placing and handling the rotisserie motor and s
Download Pdf Manuals
Related Search