Vivitar ViviCam 2800 Digital Camera
Contents
1. E E vitar ViviCam 2800 Digital Camera Quick Start Camera Power L Power up the camera using the either the AC adapter or place four B eT AA batteries in the battery bay of camera 2 To use the AC adapter plug the adapter into a household AC outlet ts open the side compartment door of camera and connect the adapter el VEEE terminal to lower jack labeled DC 6V Th 3 To use batteries slide the battery door in the direction of the arrow ar and insert the batteries noting the proper polarity tS Note Your ViviCam 2800 has a power management feature designed to extend battery life The camera will shut off automatically if it is left idle for one minute To wake up the camera press the shutter button Mode Switch Green LED DISP Display Button Image Information Battery LCD LCD Door Taking an Image A digital picture 1 Open the side compartment door and check to see that a Compact Flash CF memory card is in the memory card slot 2 Slide the mode switch to the CAM position 3 You will hear the camera start up and the Green LED will illuminate The Information LCD will indicate battery status and the current Flash Mode 4 To turn on the image LCD press the DISP Button The image LCD is not required to take an image 5 Center your subject in the optical viewfinder or in the image LCD 6 Press the shutter button to capture an image It takes about 10 sec2. onds for the image to be processed and stored Note To use digital zoom turn on the image LCD and zoom in and out using the T telephoto and W wide buttons Shutter Reviewing Your Images OK 1 Open the side compartment door and check to see that a Compact Flash CF memory cardisin T Ss the memory card slot kiy ke 2 Slide the mode switch to PLAY ty rl 3 You can review the images on the memory card by pressing the and keys aN a Note To view an image without all the image information press DISP jae il Setting Flash Mode The V2800 has four flash modes including red eye reduction Press the Flash button to change flash modes For additional detail please refer to the User s Manual Using the Macro Mode The V2800 has a Macro close focus feature It allows you to take an image of an object as close as five or six inches Press Macro button select this feature Refer to the User s Manual for more detail Installing and Removing the CF Memory Card Inserting a CF card 1 Open the side compartment door 2 Insert the side of a CF card with the 50 small holes into the CF slot pointed into the camera 3 Push the CF card into the slot until it is seated firmly Removing a CF card 1 Open the side compartment door 2 Slide the memory card ejector in the direction of the arrow Microphone 3 Remove Card CF Card Ejector Erasing an Image 1 Slide the mode swi
3. ormal then hold the shutter recording up to 20 seconds of sound with the button firmly while recording up to 20 seconds of embedded microphone sound with the embedded microphone Setting Resolution and Image Quality The ViviCam 2800 provides two resolution modes Large 1024x768 and Small 640x480 and three quality modes Good Better and Best You can change resolution and quality at any time Refer to the User s Manual for detail PC Communications The V2800 can communicate with your PC by serial cable USB or through an optional card reader If you wish to transfer voice attachments to your PC you must use either USB or a card reader For more information about the USB and Serial communications please refer to the User s Manual Other Camera Settings There are numerous other features of the ViviCam 2800 that are discussed in the User s Manual 2
4. tch to PLAY 2 Press the Menu key once to activate the menu Page of 3 3 Choose Erase by pressing the Enter key 4 Use the or to choose between erasing one or all images You can even format the CF card sae 5 Press enter and follow the screen instructions using or to select images for deletion Burst Mode The ViviCam 2800 has a burst mode allowing you to take nine sequential images Switch mode switch to CAM Press Menu key to enter menu Page of 4 Use the key to move to Picture Type then press Enter key Use the Key to select Burst then press Enter then DISP When you are capturing a burst sequence hold the shutter button firmly ee AT Adding Sound to an Image The V2800 can record up to 20 seconds of sound attached to an image as it is taken real time or anytime thereafter To add sound to your images in real time 1 Slide the mode switch to CAM To add sound to an existing image 2 Press Menu key to activate menu Page of 4 1 Slide mode switch to PLAY 3 Use the key to move to Picture Type then 2 Press Menu key to activate menu Page of 3 press Enter key 3 Use the key to move to Attach Voice then 4 Use the key to select Still with Voice then press Enter key press Enter then DISP 4 To record press and hold the enter key firmly while 5 Capturing an image as n
Download Pdf Manuals
Related Search