Home

GE DBL333EBCC 5.7 cu. ft. Electric Dryer

image

Contents

1. Ss S Ss Troubleshooting Tips Consumer Support Installing the dryer Read these instructions completely and carefully 18 Gas Connection for Gas Dryers 7 Remove the shipping cap from gas pipe at the rear of the dryer NOTE DO NOT connect the dryer to LP gas service without converting the gas valve An LP conversion kit Pub No 14 4038 MUST be installed by a qualified gas technician Connect a 1 2 1 27 cm LD semi rigid or approved pipe from gas supply line to the 3 8 0 96 cm pipe located on the back of the dryer Use a 1 2 to 3 8 1 27 cm to 0 96 cm reducer for a connection Apply an approved thread sealer that is resistant to the corrosive action of liquefied gases on all pipe connections 3 Open the shutoff valve in the gas supply line Test all connections by brushing on a soapy water solution Before Operating the Dryer 7 Connect the exhaust duct to outside exhaust system Use duct tape to seal all joints 2 With the dryer in its final position adjust one or more of the legs until the dryer is resting solidly on all four legs Place a level on top of the dryer THE DRYER MUST BE LEVEL AND RESTING SOLIDLY ON ALL FOUR LEGS Plug the power cord into a grounded outlet NOTE Check to ensure the power is off at circuit breaker fuse box before plugging the power cord into the outlet Turn on the
2. 24 CFR Part 32 80 or when such standard is not applicable with American National Standard for Mobile Homes ANSI NFPA No 501B Correct A m G The dryer is designed under ANSI Z 21 5 1 for HOME USE only gt lt S12 120 7 cm 43 8 11 1 Optional vent knockout 27 68 6 cm 3 3 4 9 5 cm SIDE VIEW Servicing Consideration must be given to provide adequate clearances for installation and servicing 15 suoi anijsu ajes suomanajsu Guyesadg z E E A S Y e a sdij pioddngs 1 Safety Instructions Operating Instructions o Ss S S Troubleshooting Tips Consumer Support 16 Installing the dryer Read these instructions completely and carefully AT Grounding Requirements A DAN GER Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded Grounding must be in accordance with local codes and ordinances or in the absence of local codes in accordance with the National Electrical Code ANSI NFPA No 70 For a grounded cord connected electric dryer 7 The dryer MUST be grounded In the event of a malfunction or breakdown grounding will reduce the risk of electrical shock
3. 30 C 85 F suomanajsu Guyesadg BLEACH LABELS Bleach symbols Any bleach Only non chlorine bleach Do not bleach when needed when needed DRY LABELS OQO IO IO K amp Do not dry Normal Permanent Press Gentle Do nottumble dry used with wrinkle resistant delicate do not wash docs e 2 EY e 3 A S S a High Medium No heat air sdij Burjooisa qnoa va E Ml E instructions Line dry Drip dry Dry flat In the shade hang to dry pioddns sauinsuoy Preparing to install your dryer e S Read these instructions completely and carefully 4 WARNING E This dryer must be exhausted to the outdoors W The National Fuel Gas code restricts installations T Use only rigid metal or flexible metal 4 of gas appliances in garages They must be 18 N diameter ductwork for exhausting to the 45 7 cm off the ground and protected from outside Use only rigid metal 4 diameter vehicles by a barrier See Location of Your Dryer ductwork inside the dryer cabinet section 2 W Never use plastic or other combustible ductwork W The electrical service to the dryer must S See Exhausting section conform with local codes and ordinances and S B This appliance must be properly grounded e is cee a SNA Ona Ss and installed as described in these nstallation i e Instructions E The gas service to the dryer must conform wi
4. approved vent hood which has swing out dampers that open when the dryer is in operation When the dryer stops the dampers automatically close to prevent drafts and the entrance of insects and rodents To avoid restricting the outlet maintain a minimum of 12 30 5 cm clearance between the vent hood and the ground or any other obstruction Safety Instructions If all rigid metal duct cannot be used then flexible all metal venting can be used but it will reduce the maximum recommended duct length See Additional Installation Instructions following Correct Operating Instructions o Ss S S SS tg SSSSSSSSSSSSS A WARNIN G The following are specific requirements for proper and safe operation of your dryer Failure to follow these instructions can create excessive drying times and fire hazards DO NOT use plastic flexible duct to exhaust the dryer Excessive lint can build up inside exhaust system and create a fire hazard and restrict air flow Restricted air flow will increase drying times If your present system is made up of plastic duct or metal foil duct replace it with rigid or flexible metal duct Ensure the present duct is free of any lint prior to installing dryer duct Troubleshooting Tips Additional Installation Instructions If all rigid metal duct cannot be used then flexible all metal venting can be used but it will reduce the maximum recommended duct length
5. connectors The use of old flexible connectors can cause gas leaks and personal injury Always use NEW flexible connectors when installing a gas appliance 7 Installation MUST conform with local codes or in the absence of local codes with the National Fuel Gas Code ANSI 7223 1 latest edition The gas supply line should be of 1 2 1 27 cm rigid pipe 3 If codes allow flexible metal tubing may be used to connect your dryer to the gas supply line The tubing MUST be constructed of stainless steel or plastic coated brass N The gas supply line MUST have an individual shutoff valve A 1 8 0 32 cm NPT minimum plugged tapping accessible for test gauge connection MUST be installed immediately upstream of the gas supply connection to the dryer A The dryer and its individual shutoff valve MUST be disconnected from the gas supply piping system during any pressure testing of the gas supply piping system at test pressures in excess of 1 2 psig 3 45 kPa The dryer MUST be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1 2 psig 3 45 kPa 13 suoi anijsu ajes suoioanajsu Guyesadg z E E A S a sdij pioddns sauinsuoy Safety Instructions Operating Instructio
6. an individual properly grounded branch circuit protected by a 15 or 20 amp circuit breaker or time delay fuse If the electric supply provided does not meet the above specifications it is recommended that a licensed electrician install an approved outlet Ensure proper ground exists before use Electrical Requirements This dryer must be connected to a 208V or 240V individual branch circuit protected by 30 amp circuit breakers or time delay fuses Use copper conductors only f the electric supply does not meet the above specifications call a licensed electrician NOTE A wiring diagram is located inside the control panel Electrical Connection Information for Gas Dryers External Ground if required An external ground wire not provided which meets local codes may be added by attaching it to the green ground screw on the rear of the dryer in the upper left corner above the cord and to grounded metal cold water pipe or other established ground Attach ground wire obtain locally NOTE A wiring diagram is located inside the control panel 11 suo n nysuj ajes suomanajsu Guyesadg z E E A S Y e a sdij Burjooisa qnoa pioddngs sauinsuoy Exhausting the dryer Read these instructions completely and carefully Exhaust System Requirements Use only 4 10 2 cm diameter minimum rigid metal duct for best performance or flexible metal duct Use
7. by creating a path of least resistance for electrical current If your dryer is equipped with a power supply cord having an equipment grounding conductor and a grounding plug the plug MUST be plugged into an appropriate copper wired receptacle that is properly installed and grounded in accordance with all local codes and ordinances f in doubt call a licensed electrician A WARNIN G The following are specific requirements for proper and safe electrical installation of your dryer Failure to follow these instructions can create electrical shock and or a fire hazard A WARNIN G This appliance MUST be properly grounded Electrical shock can result if the dryer is not properly grounded Follow the instructions in this manual for proper grounding A WARNIN G DO NOTuse an extension cord with this dryer Some extension cords are not designed to withstand the amounts of electrical current this dryer utilizes and can melt creating electrical shock and or fire hazard Locate the dryer within reach of the wall outlet taking into account the length of power cord to be purchased and allowing some slack in the cord Refer to Electrical Requirements in this manual for the proper power cord to be purchased For a permanently connected electric dryer E The dryer MUST be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and connected
8. convenience and faster service you can now download Owner s Manuals order parts catalogs or even schedule service on line You can also Ask Our Team of Experts your questions and so much more Schedule Service GEAppliances com Expert GE repair service is only one step away from your door Get on line and schedule your service at your convenience 24 hours any day of the year Or call 800 GE CARES 800 432 2737 during normal business hours Real Life Design Studio GEAppliances com GE supports the Universal Design concept products services and environments that can be used by people of all ages sizes and capabilities We recognize the need to design for a wide range of physical and mental abilities and impairments For details of GE s Universal Design applications including kitchen design ideas for people with disabilities check out our Website today For the hearing impaired please call 800 TDD GEAC 800 833 4322 Extended Warranties GEAppliances com Purchase a GE extended warranty and learn about special discounts that are available while your warranty S is still in effect You can purchase it on line anytime or call 800 626 2224 during normal business hours GE Consumer Home Services will still be there after your warranty expires Parts and Accessories GEAppliances com Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes VISA Maste
9. power at the circuit breaker fuse box A WARNING never test GAS LEAKS WITH AN OPEN FLAME NOTE On gas dryers before the burner will light it is necessary for the gas line to be bled of air If the burner does not light within 45 seconds the first time the dryer is turned on the safety switch will shut the burner off If this happens turn the timer to OFF and wait 5 minutes before making another attempt to light In the Commonwealth of Massachusetts E This Product must be installed by a licensed plumber or gas fitter E When using ball type gas shut off valves they shall be the T handle type A flexible gas connector when used must not exceed 3 feet A CA U ON Before operating the dryer make sure the dryer area is clear and free from combustible materials gasoline and other flammable vapors Also see that nothing such as boxes clothing etc obstructs the flow of combustion and ventilation air Run the dryer through cycle check for proper operation 6 If your dryer does not operate please review the Troubleshooting Tips section in this manual before calling for service Place these instructions in a location near the dryer for future reference Replacement Parts If replacement parts are needed for your dryer visit A WA RNING he aeracion the GEAppliances com or call GE Parts and Accessories Veihesfi ind ih at 800 626 2002 or contact an authoriz
10. solvent or that contains flammable materials such as cleaning cloths mops towels used in beauty salons restaurants or barber shops etc must not be placed in or near the dryer until solvents or flammable materials have been removed There are many highly flammable items used in homes such as acetone denatured alcohol gasoline kerosene some household cleaners some spot removers turpentines waxes wax removers and products containing petroleum distillates The laundry process can reduce the flame retardancy of fabrics To avoid such a result carefully follow the garment manufacturer s care instructions WB Do not dry articles containing rubber plastic or similar materials such as padded bras tennis shoes galoshes bath mats rugs bibs baby pants plastic bags pillows etc that may melt or burn Some rubber materials when heated can under certain circumstances produce fire by spontaneous combustion WB Do not store plastic paper or clothing that may burn or melt on top of the dryer during operation Garments labeled Dry Away from Heat or Do Not Tumble Dry such as life jackets containing Kapok must not be put in your dryer E Do not dry fiberglass articles in your dryer Skin irritation could result from the remaining particles that may be picked up by clothing during subsequent dryer uses B To minimize the possibility of electric shock unplug this appliance from the power supply or disconne
11. static conditioner We recommend you use either a fabric softener in the wash cycle according to the manufacturer s instructions for those products or try a dryer added product for which the manufacturer gives written assurance on the package that their product can be safely used in your dryer Service or performance problems caused by use of these products are the responsibility of the manufacturers of those products and are not covered under the warranty to this appliance GEAppliances com Grasp the plug firmly when disconnecting this ll Before discarding a dryer or removing it appliance to avoid damage to the cord while from service remove the dryer door to pulling Place the cord away from traffic areas prevent children from hiding inside so it will not be stepped on tripped over or i Bl Do not tamper with controls subjected to damage P th controls WB Do not attempt to repair or replace any part of this appliance or attempt any servicing unless specifically recommended in this Owner s Manual or in published user repair instructions that you understand and have the skills to carry out READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY o D SAVE THESE INSTRUCTIONS suo n nysuj ajes suononysuy Guyesadg 2 EY e 3 A S S a sdij pioddns sauinsuoy About the control panel You can locate your model number on the label on the front of the left side of the do
12. to the equipment grounding terminal or lead on the appliance For a cord connected gas dryer W This dryer is equipped with a three prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded three prong receptacle Do not cut or remove the grounding prong from this plug Jn Electrical Installation for Electric Dryers A WARNIN G A UL approved strain relief must be installed onto power cord If the strain relief is not attached the cord can be pulled out of the dryer and can be cut by any movement of the cord resulting in electrical shock A WA RN G Use copper receptacles only NOTE Dryers operating on 208 volt power supply will have longer drying times than those operating on 240 volt power supply A wiring diagram is located inside the control panel 3 Wire System for Electric Dryers DO NOT use for Mobile Home Installations 7 Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner 2 Install a UL approved strain relief into the power cord entry hole of the mounting bracket Use a strain relief which attaches to the mounting bracket with a nut Finger tighten the nut only at this time 3 Thread a UL approved 30A 240V 3 10 AWG minimum copper conductor power cord through the strain relief ara Silver
13. GEAppliances com Safety Instructions 2 5 Operating Instructions Control 6 Control 7 Loading and Using the Dryer 8 9 Installation Instructions Electrical Requirements 11 Exhausting the Dryer 12 Installing the Dryer 13 19 Preparing to Install the Dryer 10 Troubleshooting Tips 20 21 Consumer Support Consumer Support Back Cover Warranty 23 Dryers Write the model and serial numbers here Model Serial You can find them on the label on the front of the left side of the door opening Owners Manual and Installation Instructions DBL333 DCL333 DVL223 134202100B 17501807 436 49 90172 1 08 03 JR IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING A WARNING For your safety the information in this manual must be followed to minimize the risk of fire or explosion electric shock or to prevent property damage personal injury or death Safety Instructions Do not store or use gasoline or other m Installation and service must be performed flammable vapors and liquids in the by a qualified installer service agency or vicinity of this or any other appliance the gas supplier WHAT TO DO IF YOU SMELL GAS Do not try to light a match or cigarette or 4 Immediately call your gas supplier from turn on any gas or electrical appliance a neighbors phone Foll
14. In special installations when it is impossible to make a connection with the above recommendations then UL listed clothes dryer transition duct may be used as transition venting between the dryer and wall connection only The use of this ducting will affect drying time Consumer Support If flexible transition duct is necessary only UL listed duct identified for use with clothes dryers is approved 12 The dryer exhaust system MUST BE EXHAUSTED TO THE OUTSIDE of the dwelling DO NOT allow combustible materials for example clothing draperies curtains paper to come in contact with exhaust system The dryer MUST NOT be exhausted into a gas vent chimney a wall a ceiling a common duct with a kitchen exhaust or any concealed space of a building which can accumulate lint resulting in a fire hazard A DO NOT exceed the length of duct pipe or number of elbows allowed in the Maximum Length charts Lint can accumulate in the exhaust system plugging the system and creating a fire hazard as well as increasing drying times A DO NOT screen the exhaust ends of the vent system nor use any screws or rivets to assemble the exhaust system Lint can become caught in the screen on the screws or rivets clogging the duct work and creating a fire hazard as well as increasing drying times Use an approved vent hood to terminate the duct outdoors and seal all joints with duct tape All male duct pipe fittings MUST be ins
15. S REAR TOP 1 254cm O 0cm 1 254cm 15 38 1 cm Additional rear clearance may be required depending on the ducting installation Wa 1 2 54 cm Mobile Home Installation 7 Dryer MUST be exhausted outside outdoors not beneath the mobile home using metal ducting that will not support combustion Metal ducting must be 4 10 16 cm in diameter with no obstructions Rigid metal duct is preferred If dryer is exhausted through the floor the exhaust system MUST NOT terminate beneath the mobile home Termination MUST be securely fastened to the mobile home structure When installing a dryer into a mobile home a provision must be made for outside make up air Provide an opening with a free area of at least 25 square inches for introduction of outside air into the dryer room Gas dryers MUST be fastened to the floor using Mobile Home Installation Kit Pub No 14 D346 33 See the Exhaust System Requirements section for other important venting information Rough In Dimensions 26 7 8 68 3 cm co Electrical connection 2 9 16 6 5 cm lt 43 5 8 a 1107 em 36 91 5 cm 1 3 8 0 96 cm Dia 33 4 gas pipe 1 2 54 cm 9 5 cm REAR VIEW Door open 90 Installation MUST conform to current Manufactured Home Construction amp Safety Standard which is a Federal Regulation Title
16. T control clockwise to START Hold for 1 2 seconds and release Opening the door during operation will stop the dryer To restart the dryer close the door and select START to complete the cycle NOTE Drying times will vary according to the type of heat used Electric Natural or LP gas size of load types of fabrics wetness of clothes and condition of exhaust ducts Loading and using the dryer Always follow the fabric manufacturer s care label when laundering S As a general rule if clothes are sorted properly Do not overload This wastes energy and causes Safety Instructions Operating Instructions S E E Troubleshooting Tips Consumer Support for the washer they are sorted properly for the dryer Do not add fabric softener sheets once the load has become warm They may cause fabric softener stains Bounce Fabric Conditioner Dryer Sheets have been approved for use in all GE Dryers when used in accordance with the manufacturer s instructions Care and Cleaning of the Dryer The Exterior Wipe or dust any spills or washing compounds with a damp cloth Dryer control panel and finishes may be damaged by some laundry pretreatment soil and stain remover products Apply these products away from the dryer The fabric may then be washed and dried normally Damage to your dryer caused by these products is not covered by your warranty The Lint Filter Clean the lint filter before
17. ch the washer height The dryer must be level and rest firmly on all four leveling legs 8 Connect the power supply Check the operation of the power supply Foam shipping pad and venting 7 Place the Owner s Manual and the t Installation Instructions in a location where they will be noticed by the owner S S e E E S Packing 10 Electrical requirements Read these instructions completely and carefully Flectrical Connection Information for Electric Dryers J A WARNING 1 reduce the risk of fire electric shock or personal injury DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE THIS APPLIANCE MUST BE PROPERLY GROUNDED This dryer must be electrically grounded in accordance with local codes and ordinances or in the absence of local codes in accordance with the NATIONAL ELECTRICAL CODE ANSI NFPA NO 70 A WARNING ro reduce the risk of fire electric shock or personal injury DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE DO NOT UNDER ANY CIRCUMSTANCES CUT REMOVE THE THIRD GROUNDING PRONG FROM THE POWER CORD This dryer must be electrically grounded in accordance with local codes and ordinances or in the absence of local codes in accordance with the NATIONAL ELECTRICAL CODE ANSI NFPA NO 70 Electrical Requirements This dryer must be supplied with 120V 60 Hz and connected to
18. ct the dryer at the household distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning except the removal and cleaning of the lint filter NOTE Turning the Cycle Selector knob to an off position or pressing PAUSE does NOT disconnect the appliance from the power supply E Do not spray any type of aerosol into on or near dryer at any time ll Do not place items exposed to cooking oils in your dryer Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire E Never attempt to operate this appliance if itis damaged malfunctioning partially disassembled or has missing or broken parts including a damaged cord or plug B The interior of the machine and the exhaust duct connection inside the dryer should be cleaned at least once a year by a qualified technician See the Loading and Using the Dryer section Do not use any type of spray cleaner when cleaning dryer interior Hazardous fumes or electrical shock could occur If yours is a gas dryer it is equipped with an automatic electric ignition and does not have a pilot light DO NOT ATTEMPT TO LIGHT WITH A MATCH Burns may result from having your hand in the vicinity of the burner when the automatic ignition turns on You may wish to soften your laundered fabrics or reduce the static electricity in them by using a dryer applied fabric softener or an anti
19. ctwork which runs through an unheated area or is near an air conditioning duct should be insulated to reduce condensation and lint build up MAXIMUM LENGTH of 4 10 2 cm Dia FLEXIBLE METAL DUCT PREFERRED VENT HOOD TYPE PREFERRED VENT HOOD TYPE 4 10 2 cm Louvered Number of 90 turns 102 SP 1584m 40 12 19 4F i341m 37 975m 3 83 97m 24 731m 2 28 853m 16 487m Exhaust Direction INSTALL MALE FITTINGS IN CORRECT DIRECTION 4 10 2 cm Louvered Number of 90 turns gt 102 cal o 83 914m 18 549m Poa zzr 67m 427m 2 1 A27m 10 305 3 not recommended INCORRECT All dryers are shipped set up for rear exhausting On electric dryers exhausting can be on the cabinet right or left side or through the dryer bottom Gas dryers can exhaust on the cabinet right side or the dryer bottom To change exhaust direction you will need Exhaust Kit Pub No 14 A018 and a rigid metal 4 90 degree elbow The kit is available through your GE retailer Follow the instructions supplied with the kit Gas Supply Requirements EXHAUST DUCT LOCATING DIMENSIONS Same as l other side 5 7 8 3 3 4 9 5 at tar 9 5 cm A Replace brass connecting pipe that is not plastic coated Stainless steel or plastic coated brass MUST be used WARNIN G Never reuse old flexible
20. d screw located above the terminal block 2 e Black 240V conductor Typical receptacle cord White neutral Red 240V Green ground Thread UL approved 30A 240V 4 10 AWG minimum copper conductor power cord through the strain relief Attach the green power cord ground wire to the cabinet with the green ground screw Attach the white neutral power cord conductor from the power cord and the green ground wire from the dryer harness to the silver colored center terminal on the terminal block Tighten the screw securely 7 Attach the red and black power cord conductors to the outer brass colored terminals on the terminal block Green power cord ground wire Green ground ap screw DIV ar _ Silver terminal Y lerminal block Green neutral Flack ground wire Es Whit Du Tighten nut to Red these threads bracket A WARNING Do not make a sharp bend or crimp wiring conductor at the connections Tighten the fasteners securing the cord restraint firmly against the power cord Tighten the strain relief nut securely so the strain relief does not turn 70 Reinstall the terminal block access cover 17 suoyaonysuy ajes suomanajsu Guyesadg zl E E A S 2 a sdij yioddns sauinsuoy Safety Instructions Operating Instructions
21. each use Remove by pulling straight up Run your fingers across the filter A waxy buildup may form on the lint filter from using dryer added fabric softener sheets To remove this buildup wash the lint screen in warm soapy water Dry thoroughly and replace Do not operate the dryer without the lint filter in place Have a qualified technician vacuum the lint from the dryer once a year ail Sorting and Loading Hints wrinkling Do not dry the following items fiberglass items woolens rubber coated items plastics items with plastic trim and foam filled items The Exhaust Duct Inspect and clean the exhaust ducting at least once a year to prevent clogging A partially clogged exhaust can lengthen the drying time Follow these steps 7 Turn off electrical supply by disconnecting the plug from the wall socket 2 Disconnect the duct from the dryer 3 Vacuum the duct with the hose attachment and reconnect the duct The Exhaust Hood Check from the outside that the flaps of the hood move freely when operating Make sure that there is no wildlife birds insects etc nesting inside the duct or hood GEAppliances com Fabric Care Labels WASH LABELS wash c L_ Do not wash Do not wring Normal Permanent Press Gentle cycle wrinkle resistant delicate suoyonysuy ajes Hand wash Water temperature Hot Warm Cold cool 50 C 120 F 40 C 105 F
22. ed parts manual anid allother literature meded wi this dryer are not meant to cover every possible supplier re EE PP condition and situation that may occur Good A WA RNING Destroy the carton and safe practice and caution MUST be applied plastic bags after the dryer is unpacked when installing operating and maintaining Children might use them for play Cartons anyapplianee covered with rugs bedspreads or plastic sheets can become airtight chambers causing suffocation Place all materials in a garbage container or make materials inaccessible to children suoianijsu ajes suononysuy Guyesadg Reversing the Dryer Door Swing 7 Open the dryer door Remove the 4 hinge hole plugs or screws from the left side of door E opening Place nearby for future installation NOTE You may need a plastic knife to help pull out the plugs Be careful not to scratch the paint E Remove the four screws that secure the door hinges to the dryer front panel NOTE Remove 1 screw from each of the 2 hinges first Hold the door firmly before removing the last 2 screws Rotate the door 180 and reinstall the door hinges to the dryer front panel with the 4 screws Pd E E A S 2 a Remove 4 screws one from each hinge first Install the 4 hinge hole plugs or screws that were removed in step 1 into the open screw holes on the right side of the door opening sdij B
23. es etc out of the reach of children preferably in a locked cabinet Observe all warnings on container labels to avoid injury E Never climb on or stand on the dryer top E Do not install or store this appliance where it will be exposed to the weather suoyanysuy ajes suoyaonysuy Guyesadg 2 q e 3 A S ge S 77 sdij Burjooisa qnoa4 lt Safety Instructions Operating Instructions S S E E S E Troubleshooting Tips Consumer Support IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING A WARNING WHEN USING YOUR DRYER Never reach into the dryer while the drum is moving Before loading unloading or adding clothes wait until the drum has completely stopped W Clean the lint filter before each load to prevent lint accumulation inside the dryer or in the room DO NOT OPERATE THE DRYER WITHOUT THE LINT FILTER IN PLACE UNLESS THE DRYING RACK IS IN USE Do not wash or dry articles that have been cleaned in washed in soaked in or spotted with combustible or explosive substances such as wax oil paint gasoline degreasers dry cleaning solvents kerosene etc These substances give off vapors that may ignite or explode Do not add these substances to the wash water Do not use or place these substances around your washer or dryer during operation Any article on which you have used a cleaning
24. ing Letting items sit in dryer Remove items when cycle ends and fold or hang after cycle ends immediately Overloading e Separate large loads into smaller ones Some fabrics will naturally shrink when washed Others can be safely washed but will shrink in the dryer To avoid shrinkage follow garment care labels exactly e Some items may be pressed back into shape after drying If you are concerned about shrinkage in a particular item do not machine wash or tumble dry it 21 01 21 5 ajes suoioanajsu Guyesadg 2 e 3 A S S a sdij pioddns sauinsuoy Notes 22 suoianijsu suoianajsu Gunesadg suonanysuj uorejjejsu sdi Burjoousajqno4 yoddng GE Dryer Warranty e T All warranty service provided by our Factory Service Centers or Staple your receipt here an authorized Customer Care technician To schedule service Proof of the original purchase gt on line 24 hours a day visit us at GEAppliances com or call date is needed to obtain service Ed 800 GE CARES 800 432 2737 under the warranty s S For The Period Of Will Replace a One Year Any part of the dryer which fails due to a defect in materials or workmanship During this From the date of the full one year warranty GE will also provide free of charge all labor and related service costs original purchase to replace the defective
25. ing times of heat used electric natural or LP gas size of load types of fabrics wetness of clothes and condition of exhaust ducts Clothes take Improper sorting Separate heavy items from lightweight items generally too long to dry a well sorted washer load is a well sorted dryer load Large loads of heavy fabrics Large heavy fabrics contain more moisture and take like beach towels longer to dry Separate large heavy fabrics into smaller loads to speed drying time Controls improperly set Match control settings to the load you are drying Lint filter is full Clean lint filter before every load Clothes are wrinkled Clothes shrink Improper or obstructed ducting Check installation instructions for proper ducting venting Make sure ducting is clean free of kinks and unobstructed Check to see if outside wall damper operates easily Check the Installation Instructions to make sure the dryer venting is correct Blown fuses or tripped Replace fuses or reset circuit breakers Since most dryers circuit breaker use two fuses or breakers make sure both are operating Overloading combining loads Do not put more than one washer load in the dryer ata time Underloading If you are drying only one or two items add a few items to ensure proper tumbling Overdrying e Select a shorter drying time Remove items while they still hold a slight amount of moisture Select a LESS DRY sett
26. ns o Ss S S Troubleshooting Tips Consumer Support Installing the dryer Read these instructions completely and carefully 14 Location of Your Dryer Do Not Install the Dryer 7 Do not install the dryer in an area exposed to dripping water or outside weather conditions 2 Do not install the dryerin an area where it will come in contact with curtains drapes or anything that will obstruct the flow of combustion and ventilation air Installation in Recess or Closet 7 This dryer MUST be exhausted outdoors 12 No other fuel burning appliance shall be installed in the same closet as the GAS DRYER 3 Your dryer needs the space around it for proper ventilation DO NOT INSTALL YOUR DRYER IN A CLOSET WITH A SOLID DOOR Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq in of open area equally distributed If the closet contains both a washer and a dryer doors must contain a minimum of 120 sq in of open area equally distributed Air openings are required to be unobstructed when a door is installed A louvered door with equivalent air openings for the full length of the door is acceptable 60 sq in 387 1 sq cm Closet door 3 Do not install the dryer on carpet Floor MUST be solid with a maximum slope of 1 2 54 cm Allow the following clearances for ease of installation FRONT SIDE
27. or opening Model DBL333 MORE DRY LESS DRY TEMPERATURE mM LESS DRY COOL DOWN MEDIUM COTTONS EASY CARE REGULAR _ FLUFF AUTOMATIC AUTOMATIC e NO HEAT MORE DRY 80 MIN 7 TIMED DRY 60 1 Model DCL333 LESS DRY MORE DRY OPTIMUM DRY COTTONS pow EASY CARE AUTOMATIC AUTOMATIC REGULAR HEAT MEDIUM HEAT MORE DRY LESS DRY 70 MIN FLUFF NO HEAT Model DVL223 LESS DRY OPTIMUM DRY TIMED DRY COTTONS MEDIUM HEAT AUTOMATIC 50 REGULAR HEAT MORE DRY About the control settings NOTE Not all features are available on all dryer models GEAppliances com IMPORTANT Clean the lint filter each time you use the dryer lu Temperature REGULAR For regular to heaw cottons MEDIUM For synthetics blends delicates and items labeled permanent press FLUFF For fluffing items without heat Use the TIMED DRY cycle NO HEAT Automatic cycles automatically determine fabric dryness Select LESS DRY if you want your clothes slightly damp at the end of the drying cycle Select MORE DRY if you want them to feel drier Drying Cycles COTTONS For cottons and most linens For most loads select OPTIMUM DRY EASY CARE For wrinkle free permanent press and delicate items and knits TIMED DRY Setthe Cycle Selector at the desired drying time FLUFF Provides no heat tumbling for freshening or fluffing already dry clothing fabric linens and pillows Start Close the dryer door Turn the STAR
28. or space or adjust leveling legs makes noise Dryer may be sitting unevenly as necessary until even Greasy spots on clothes Improper use of fabric softener Follow directions on fabric softener package Drying dirty items with clean ones Use your dryer to dry only clean items Dirty items can stain clean items and the dryer Clothes were not completely clean Sometimes stains which cannot be seen when the clothes are wet appear after drying Use proper washing procedures before drying Lint on clothes Lint filter is full Clean lint screen before each load Improper sorting Sort lint producers like chenille from lint collectors like corduroy Static electricity can attract lint See suggestions in this section under STATIC Overloading e Separate large loads into smaller ones Paper tissue etc left in pockets Empty all pockets before laundering clothes Static occurs No fabric softener was used Try a fabric softener Bounce Fabric Conditioner Dryer Sheets have been approved for use in all GE Dryers when used in accordance with the manufacturer s instructions Overdrying Try a fabric softener Adjust controls to LESS DRY Synthetics permanent press and blends can cause static 20 Try a fabric softener GEAppliances com Problem Possible Causes What To Do Inconsistent Type of heat Automatic drying times will vary according to the type dry
29. ow the gas suppliers instructions carefully Do not touch any electrical switch do not use any phone in your building 5 cannot reach your gas supplier call the fire department o S S E IS 3 e 3 Clear the room building or area of all occupants California Safe Drinking Water and Toxic Enforcement Act This act requires the governor of California to publish a list of substances known to the state to cause cancer birth defects or other reproductive harm and requires businesses to warn customers of potential exposure to such substances Gas appliances can cause minor exposure to four of these substances namely benzene carbon monoxide formaldehyde and soot caused primarily by the incomplete combustion of natural gas or LP fuels Installation Instructions Properly adjusted dryers will minimize incomplete combustion Exposure to these substances can be minimized further by properly venting the dryer to the outdoors Troubleshooting Tips Consumer Support A WARNING PROPER INSTALLATION GEAppliances com This dryer must be properly installed and located in accordance with the Installation Instructions before it is used WB Properly ground dryer to conform with all governing codes and ordinances Follow details in the nstallation Instructions section Bi Install or store where it will not be exposed to temperatures below freezing o
30. part S t What GE Will Not Cover E H Service trips to your home to teach you how to use E Replacement of house fuses or resetting of circuit gt the product breakers s E Improper installation delivery or maintenance E Damage to the product caused by accident fire floods S Bi Failure of the product if it is abused misused or used for peach of God S other than the intended purpose or used commercially Incidental or consequential damage caused by possible 7 E Replacement of the light bulb appliance ll Damage caused after delivery This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA In Alaska the warranty excludes the cost of shipping or service calls to your home Some states do not allow the exclusion or limitation of incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights which vary from state to state To know what your legal rights are consult your local or state consumer affairs office or your state s Attorney General 2 e 3 A S S a Warrantor General Electric Company Louisville KY 40225 sdij Burjooisa qnoa4 pioddns sauinsuoy 23 Consumer Support GE Appliances Website GEAppliances com Have a question or need assistance with your appliance Try the GE Appliances Website 24 hours a day any day of the year For greater
31. r exposed to the weather Connect to a properly rated protected and sized power supply circuit to avoid electrical overload ll Remove all sharp packing items and dispose of all shipping materials properly YOUR LAUNDRY AREA WB Keep the area underneath and around your appliances free of combustible materials such as lint paper rags chemicals gasoline and other flammable vapors and liquids Keep the floor around your appliances clean and dry to reduce the possibility of slipping Keep area around the exhaust opening and surrounding areas free from the accumulation of lint dust and dirt E Do not obstruct the flow of ventilating air Do not stack or place laundry or throw rugs against the front or back of the dryer Exhaust Ducting 7 2 Follow details in the nstallation Instructions section This dryer MUST be exhausted to the outside Use only rigid metal 4 diameter ductwork inside the dryer cabinet Use only rigid metal or flexible metal 4 diameter ductwork for exhausting to the outside USE OF PLASTIC OR OTHER COMBUSTIBLE DUCTWORK CAN CAUSE A FIRE PUNCTURED DUCTWORK CAN CAUSE A FIRE IF IT COLLAPSES OR BECOMES OTHERWISE RESTRICTED IN USE OR DURING INSTALLATION E Close supervision is necessary if this appliance is used by or near children Do not allow children to play on with or inside this or any other appliance Keep all laundry aids such as detergents bleach
32. rCard and Discover cards are accepted Order ondine today 24 hours every day or by phone at 800 626 2002 during normal business hours Instructions contained in this manual cover procedures to be performed by any user Other servicing generally should be referred to qualified service personnel Caution must be exercised since improper servicing may cause unsafe operation Contact Us GEAppliances com KoA If you are not satisfied with the service you receive from GE contact us on our Website with all the details including your phone number or write to General Manager Customer Relations GE Appliances Appliance Park Louisville KY 40225 Register Your Appliance GEAppliances com Register your new appliance on line at your convenience Timely product registration will allow for enhanced communication and prompt service under the terms of your warranty should the need arise You may also mail in the pre printed registration card included in the packing material Printed in the United States
33. talled downstream with the flow of air A EXPLOSION HAZARD Do not install the dryer where gasoline or other flammables are kept or stored If the dryer is installed in a garage it must be a minimum of 18 45 7 cm above the floor Failure to do so can result in death explosion fire or burns Provide an access for inspection and cleaning of the exhaust system especially at turns Inspect and clean at least once per year Do not obstruct incoming or exhausted air The following directions must be followed Use the shortest length possible Stretch the duct to its maximum length Do not crush or collapse Never use transition duct inside the wall flooring ceiling or inside the dryer Avoid resting the duct on sharp objects Venting must conform to local building codes Installing the dryer Exhaust Ducting Length The exhaust system should be inspected and cleaned at least once a year with normal usage The more the dryer is used the more often you should check the exhaust system and vent hood for proper operation If roof vents or louvered plenums are used they must be equivalent to a 4 dampered wall cap in regard to resistance to airflow prevention of back drafts and maintenance required to prevent clogging MAXIMUM LENGTH of 4 10 2 cm Dia RIGID METAL DUCT DO NOT assemble the duct work with fasteners that extend into the duct They will serve as collection points for lint Du
34. terminal Green ground screw ep A Bgm mE Green neutral ground wire Tighten nut to these threads Use copper Power cord conductors only Strain relief mounting bracket Attach the power cord neutral center wire conductor to the silver colored center terminal on the terminal block Tighten the screw securely Attach the remaining two power cord outer conductors to the outer brass colored terminals on the terminal block Tighten both screws securely A WARNING Do not make a sharp bend or crimp wiring conductor at connections 6 Reattach the strain relief mounting bracket to the back of the dryer with two screws Tighten screws securely Tighten the fasteners securing the cord restraint firmly against the power cord 8 Tighten the strain relief nut securely so that the strain relief does not turn 9 Reinstall the terminal block access cover 4 Wire System for Electric Dryers MUST be used for Mobile Home Installations Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner E Install a UL approved strain relief in the entry hole of the mounting bracket Use a strain relief which attaches to the mounting bracket with a nut Finger tighten the nut only at this time 3 Remove the green neutral ground wire from the green groun
35. th Bosne amos TEN local codes and ordinances or the latest edition gt VOR Cort EQUAL a AS HM RED of the National Fuel Gas Code ANSI Z223 1 S where it will be exposed to water weather The gas dryer is designed under ANSI Z 21 5 1 See Location of Your Dryer section is for home use only This dryer is not 2 recommended for commercial applications e such as restaurants or beauty salons etc Tools and Materials Required for Dryer Installation Phillips head screwdriver Rigid or flexible metal 4 10 2 cm duct L Adjustable pliers Vent hood Q Carpenter s level Pipe thread sealer GAS DRYER Flat or straight blade screwdriver Duct tape Installation Instructions Preparing the Installation Site and Unpacking the Dryer 7 Prepare the area and exhaust for installation A C A UTIO N docent of the new dryer do not use the control panel as a means E Check to be sure that the existing external to pick up or move the dryer exhaust is clean and that it meets attached installation specifications 4 Return the dryer to an upright position 3 Using the four shipping carton corner posts as padding two on each side carefully lay the dryer on its left side and remove foam shipping pad Move the dryer to the desired location Troubleshooting Tips Connect the external exhaust N S lt Adjust the leveling legs to mat
36. urjooisa qnoa pioddns 19 Safety Instructions Operating Instructions S S E E Troubleshooting Tips Consumer Support Before you call for service Troubleshooting Tips Save time and money Review the charts on the following pages or visit GEAppliances com You may not need to call for service Problem Possible Causes What To Do Dryer doesn t start Dryer is unplugged Make sure the dryer plug is pushed completely into the outlet Fuse is blown circuit breaker Check the household Distribution Panel fuse circuit is tripped breaker box in your home and replace fuse or reset breaker NOTE Electric dryers use two fuses or breakers Thermal limiter tripped Check the vent for any obstructions Call authorized service person for replacement if necessary Dryer doesn t heat Fuse is blown circuit breaker Check the fuse circuit breaker box in your home is tripped the dryer may tumble and replace both fuses or reset both breakers but not heat Your dryer may tumble if only one fuse is blown or one breaker tripped Gas service is off Make sure gas shutoff at dryer and main shutoff are fully open LP gas supply tank is empty Refill or replace tank Dryer should heat when utility or there has been a utility service is restored interruption of natural gas gas models Dryer shakes or Some shaking noise is normal Move dryer to an even flo

Download Pdf Manuals

image

Related Search

Related Contents

Caja Torre RAID Matriz Array de Discos Duros 2 Bahías SATA  Samsung MJC-4000 用户手册  prima di utilizzare il monitor  Haier WDNS055 Water Dispenser User Manual  Linak MEDLINE MJB User's Manual  Samsung SGH-F300 Наръчник за потребителя  Cache Latencies of the PowerPC MPC7451  User Manual SpitJack P80 Rotisserie  RT- ZBAS - Kolter Electronic  Descarregue o manual do utilizador em gopro.com/support GUIA  

Copyright © All rights reserved.
Failed to retrieve file