Ritchie Helmsman Hd 75 Compass Deck Mount
Contents
1. With the compass mounted temporarily in its intended position try moving the steering wheel throttle controls or anything else that might cause deviation It is also advised to turn electrical devices off and on Please be advised that a changing magnetic field can not be corrected with compensation and you will need to find another location for your compass Installation all Models Mounting the Compass Great care must be taken to mount the compass so that it is aligned with the keel of the boat An alignment error is a constant error on all headings caused by the compass not being pointed in the same direction as the boat One recommendation is to temporarily mount the compass using one fastener so if an alignment error is detected it is easily corrected Masking tape can be used as a reference or to keep the compass steady during installation If you are mounting to a bulkhead that is not perpendicular to the centerline of the boat a fairing block must be used Due to variations in bulkhead and deck materials mounting screws are not supplied Use hardware that is suitable for your specific installation SELECT MOUNTING HARDWARE THAT IS NON MAGNETIC Most quality stainless steel and solid brass fasteners can be used If you are unsure test them with a magnet Most models have built in lights which will require routing the wire or wires to your power source To assure a clean installation you may want to wait and drill the routing holes after2. you are satisfied with the compass alignment Specific model installation instructions are as follows Note for all flush and bulkhead mount compasses It is important that you use the mounting gasket included with each model We do NOT recommend the use of bedding compound since some brands contain chemicals that could damage the plastic dome HF 72 HF 72W HF 73 HF 73W HF 79 HF 79G HF 79W SS 1000 amp SS 1000W Flush Mount Using the mounting template supplied with the compass make the cutout in your chosen location and mount as instructed above Mounting the Compass For all HF 79 models loosen but do NOT remove the single screw in the rear of the dress bezel Lift the rear of the dress bezel and slide it forward to remove it from the compass When mounting and compensation are completed replace the dress bezel Note If you cannot access the compensation rods from below you need to allow for easy removal of the compass during compensation See Compensation instructions below HV 76 amp HV 77 Bulkhead Mount Before making the cut make sure the bulkhead surface at the mounting location is at a ninety degree 90 angle to the centerline of the boat and is in a vertical position If such is not the case a fairing block must be used between the compass and the bulkhead Use the mounting template supplied with the compass for cutting the necessary opening in the vertical bulkhead If the compass is not mounted in a vertical position s
3. Installation Compensation and Maintenance Instructions For all RITCHIE HELMSMAN Compass Models Made in U S A CAUTION All Magnetic Compasses are vulnerable to magnetic interference which will produce errors called deviation It is the Owner Operator and or Helmsman s responsibility to make sure the compass is properly installed and compensated Compensation is the act of correcting for deviation Magnets speakers microphones etc ferrous metals steel iron etc and current carrying devices are common causes of deviation It is important to understand that magnetic compasses point toward Magnetic North There is a difference between Magnetic North and True North and that difference is called variation Variation differs depending on your geographical location and can be determined by referring to a local chart Please read the Instructions completely before beginning installation Selecting the Proper Location The compass should be close enough to the helmsman and positioned below the helmsman s line of sight so it is easily read during normal operation Direct Read Dial or CombiDamp Dial models will allow the compass to be mounted higher near or at eye level You will need a flat and level surface when the boat is on a level keel Many boats have a curved mounting surface and if this is the case a fairing block should be utilized to bring the compass to a level position Select a location that has no more that 20 deg
4. embly which should be connected to the same circuit Compensation A built in correcting magnet system consists of two sets of magnets fixed to two adjusting rods with slotted ends The slots should be horizontal before starting the adjusting procedure A small non magnetic screwdriver is provided for this purpose Before starting compensation make sure you have a suitable location see Testing Your Chosen Location Method 1 Preferred Step One With the compass in its intended position but not finally secured see Mounting the Compass select a course on your chart using two fixed aids that are within ten degrees 10 of the North South line Try to select this course so that you can maneuver your boat down range of the marks selected See example A Lae Step Two From a position down range of the North South LIGHTHOUSE oss marks and keeping the marks lined up run the boat a visually along the Northerly course selected Turn the weak REGO Ns port starboard compensator slot is facing starboard until AR the compass reads correctly DOWN RANGE N Step Three Simply repeat steps 1 amp 2 except this time using an East West course and the fore aft compensator EXAMPLE slot is facing aft Step Four Check compass alignment by running the boat in a Southerly direction again keeping the mark lined up If the compass is not correct at this time there is an alignment error To correct rotate the compass itself
5. erious errors can develop when the boat heels over and pitching occurs simultaneously There is also potential error from the built in compensator magnets if the compass is not mounted vertically HD 74 HD 75 amp SS 1100 Deck Mount Follow the instructions above Mounting the Compass After mounting remove the black plastic inserts and begin compensation see Compensation instructions below HB 70 HB 71 amp HB 85 Bracket Mount Remove the bracket from the compass and mount it as instructed above Mounting the Compass If you mounted the bracket to a gunwale simply rotate the compass 90 degrees in it s housing by removing the four Phillips head screws located in the bottom of the housing After re installing the compass in the bracket remove the black plastic inserts which cover the compensators and begin compensation see Compensation instructions below IMPORTANT NOTE REGARDING HB 85 This model is designed to be mounted on STEEL HULL Vessels Special compensation is required and you will need to hire a professional compass adjuster Night Light Wiring all Models All models are supplied with a 12 volt night lighting system To connect lights to a 24 or 32 volt system dropping resistors are available Lights should be wired to an appropriately fused 12 volt circuit in your electrical system i e running light circuit Connect the red wire white on some models to positive and black to ground Some models have a second light ass
6. ore aft compensator slot is facing aft Step Four Check compass alignment by running the boat 180 degrees from the heading used in step 2 If the compass is not correct at this time there is an alignment error To correct rotate the compass itself to remove one half of this error Repeat steps 1 2 amp 4 until your North South line is correct then repeat step 3 Step Five Upon completing the procedure secure the compass in its final position If you feel that the deviation on your boat is of an unusual nature the services of a professional compass adjuster will be a wise investment To assure accuracy on all headings check for deviation every thirty degrees and record any deviation on a deviation card We recommend checking at the start of each boating season and any time new equipment is added near the compass for deviation Maintenance Protect your compass from the sun when not using your boat Strong sunlight may decrease the life of your compass Custom fit covers are available from Ritchie Ritchie compasses require very little care To remove salt spray deposits or dirt rinse the entire compass with clean fresh water and wipe carefully with a damp cloth Important Note Never Use Chemical or Abrasive Cleaners Night Lighting Systems Ritchie s night lights are designed to last for years of use If you need to replace one contact the factory with your model and serial number for a part number and price Tel 781 826 5131 Fa
7. rees deviation on any of the four cardinal points N S E and W Most compasses have a built in compensation system that will correct for fixed deviation up to 20 degrees Itis important to realize that proper compensation is not possible when a compass is subjected to a magnetic field that is variable Some shipboard devices can cause varying magnetic fields Devices such as windshield wipers high current carrying wire and even some steering wheels must be considered when selecting a location for your compass Testing Your Chosen Location Use your compass to test a location There are two brass rods near the bottom of the compass which rotate 360 degrees the slotted ends may be all that is visible These compensation rods are used to correct your compass for deviation When testing a location you do not want pre set corrections in your compass so neutralize the comp rods by setting the slots in a horizontal position Begin your test by holding the compass away from any possible interference and observing the compass reading Then move the compass into position carefully keeping it pointed in the same direction If the compass reading is different without a change in direction you are observing deviation You need to find a location that has less than 20 degrees of deviation on the 4 cardinal points if you intend to adjust your compass using the compensator rods After finding a location you should test for intermittent changes in the magnetic field
8. to remove one half of this error Repeat steps 1 2 amp 4 until your North South line is correct then repeat step 3 Step Five Install fastener s taking care not to disturb alignment LIGHTHOUSE Jo o Par R Q A aj aS Method 2 Requires the use of GPS or Loran In this method you will be using a GPS or Loran as your reference 1 Your GPS or Loran must be set to provide you with Magnetic not True headings Check your Manual 2 GPS and Loran provide headings based on COG course over ground Compasses provide heading based on the direction the boat is actually pointed Because of Tides Currents and Winds the boat may not always point in the same direction as COG Pick a time and location that will minimize these effects 3 Because the GPS and Loran calculate COG based on current and past positions you will see greater heading accuracy while traveling at higher speeds We recommend at least 10 knots Step One While at sea with the compass in its intended position but not finally secured see Mounting the Compass obtain the Loran GPS bearing to a fixed aid or landmark that is within 10 of a North South line Step Two Position your boat along that line and steer directly at that mark Turn the port starboard compensator slot is facing starboard until the compass heading matches the Loran GPS bearing Step Three Simply repeat steps 1 amp 2 except this time using an East West course and the f
9. x 781 826 7336 E mail service ritchienavigation com Warranty We warrant all Ritchie Magnetic Marine Compasses to be free of defects in workmanship or materials If within three years of purchase date a compass fails to give satisfactory service it will be repaired or replaced without charge This warranty does not cover breakage through accident or misuse Replacement or repair will be made if the instrument is returned prepaid to a Ritchie Service Station or directly to E S Ritchie amp Sons Inc 243 Oak Street Pembroke MA 02359 RITCHIE NAVIGATION E S RITCHIE amp SONS INC P O BOX 548 243 OAK ST PEMBROKE MASSACHUSETTS 02359 U S A Tel 781 826 5131 Fax 781 826 7336 www ritchienavigation com Rev D 4 00 HL 0032 Printed in U S A
Download Pdf Manuals
Related Search