Faber Pro Magnum Wall Hood
Contents
1. A around the lamp C must be removed as indicated in FIGURE 14 This bezel A is held in place by two screws B Remove the two screws and the bezel Then remove the lamp and replace with a new lamp Once the new lamp is in place reinstall the bezel FIGURE 14 Version 12 04 Page 72. you already know how to operate it 2 The fire is small and contained in the area where it started 3 The fire department is being called 4 You can fight the fire with your back to an exit ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED MUST BE SEALED This rangehood requires at least 24 of clearance between the bottom of the rangehood and the cooking surface or countertop This minimum clearance may be higher depending on local building code For example for gas ranges a minimum of 30 may be required The maximum depth of overhead cabinets is 13 Overhead cabinets on both sides of this unit must be a minimum of 18 above the cooking surface or countertop Consult the cooktop or range installation instructions given by the manufacturer before making any cutouts MOBILE HOME INSTALLATION The installation of this rangehood must conform to the Manufactured Home Construction and Safety Standards Title 24 CFR Part 3280 formerly Federal Standard for Mobile Home Construction and Safety Title 24 HUD Part 280 Four wire power supply must be used and the appliance wiring must be revised See Electrical Requirements LISEZ BIEN CETTE FICHE AVANT D INSTALLER LA HOTTE AVERTISSEMENT POUR MINIMISER LE RISQUE D UN FEU DE GRAISSE SURLA TABLE DE CUISSON a Ne jamais laisser un l ment de la table de cuisson fonctionner sans surveillance la puissance de chauffage maximale un renversement d bordement de mati re graisseuse pourra
3. 9 For top vent applications no additional adjustments are necessary FIGURE 9 For rear vent applications the blower must be turned inside the rangehood so that the blower vents to the rear as indicated in FIGURE 10 The blower is turned by removing two screws on each side of the blower rotating the blower with the exhaust opening facing the rear and then replace the screws The exhaust cover must be moved to block the unused opening The blower must be converted before installing the rangehood FIGURE 10 4 Remove the cover from the field wiring compartment Remove the wiring electrical knockout using a flat blade screwdriver Feed the Power Supply Cable through the electrical knockout 5 The canopy attaches to the wall by two screws discussed earlier in the installation instructions The canopy hangs from these screws by brackets inside the rangehood shown in FIGURE 11 Before attempting to hang the canopy you should rotate the adjustment screw marked V1 in FIGURE 11 counterclockwise to extend the brackets from the canopy Using a Phillips head screwdriver rotate this screw counterclockwise to extend the bracket FIGURE 11 6 Install the damper before hanging the rangehood The damper attaches to the rangehood by two small screws provided in the hardware package If 48 hood is to be connected to 10 round duct install the Duct Transition Kit now 7 Hang th
4. de coudes pour la plus grande efficacit Le diam tre de tuyauterie doit tre uniforme N installez jamais 2 coudes ensemble Scellez bien tous les joints avec un ruban adh sif m tallique l int rieur et scellez bien le clapet ext rieur avec du calfeutrage Utilisez un tuyau d vacuation rigide lorsque possible Un tuyau flexible gale deux fois plus qu un tuyau rigide ce qui r duit la puissance d vacuation Un conduit d vacuation flexible cr e une contre pression et une turbulence de l air qui r duisent consid rablement la performance Veillez ce que l espace pour le tuyau soit ample ainsi on n aurait pas besoin de d couper les supports de murint rieur Si ce d coupage est n cessaire veillez bien ce qu un renforcement soit mis en place R GLEMENTS D EVACUATION ADDITIONELL PAGE 8 AVERTISSEMENT Pour Ne Pas Risquer Un Feu Utilisez Seulement Les Mat riaux M talliques Ay AVERTISSEMENT e Le syst me d vacuation DOIT sortir l ext rieur e N VACUEZ PAS le conduit soit dans une mansarde soit dans un espace enferm N UTILISEZ PAS un clapet de s choir 4 pouces N utilisez pas un conduit flexible N ENCOMBREZ PAS la circulation d air Faute de suivre cet avertissement pourrait occasionner un feu FICHE TECHNIQUE LECTRIQUE Le raccordement lectrique doitse faire avec un circuit s par de 15 amp res fusible 120V 60 Hz courant alternant On recommande un coupe cir
5. de cuisson Cette hauteur minimum peut tre plus haute suivant le code municipal Par exemple les cuisini res gaz peuvent requ rir 30 po de hauteur Les armoires au dessus ne d passeront pas 13 po de profondeur Les armoires au dessus de chaque c t devront tre au moins 18 po au dessus de la surface de cuisson Consultez la fiche technique avant de d couper les armoires L installation de cette hotte doit tre conforme aux R glements de Manufactured Home Construction and Safety Standards titre 24 CFR Section 3280 anciennement Federal Standard for Mobile Home Construction and Safety Standards titre 24 CFR Section 3280 anciennement Federal Standard for Mobile Home Construction and Safety titre 24 HUD Section 280 Le branchement lectrique se fait avec une raccordement a 4 fils Consultez la fiche technique lectrique Version 12 04 Page 1 VENTING REQUIREMENTS Determine which venting method is best for your application Ductwork can extend either through the wall or the roof The length of the ductwork and the number of elbows should be kept to a minimum to provide efficient performance The size of the ductwork should be uniform Do not install two elbows together Use duct tape to seal all joints in the ductwork system Use caulking to seal exterior wall or floor opening around the cap Flexible ductworkis not recommended Flexible ductwork creates back pressure and air turbulence that greatly reduces performanc
6. ALL 5 Determine and make all necessary cuts in the wall for the ductwork The Pro Magnum vents either through the top orthe rear of the rangehood Each rangehood is shipped from the factory vented through the top In order to vent to the rear the blower inside the rangehood must be turned to the rear The dimensions for the duct openings are given in FIGURE 8 The 48 model uses two 3 amp 1 4 by 10 duct openings Install all ductwork before installing the rangehood 6 Determine the proper location for the Power Supply Cable as indicated in FIGURE 8 Note that the 30 36 versions have the option of top or rear electrical connection while the 48 version has only the rear option Use a1 amp 1 4 Drill Bit to make this hole Run the Power Supply Cable Use caulking to seal around the hole DO NOT turn on the power until installation is complete 30 AND 36 VERSIONS Electrical Opening FIGURE 8 Version 12 04 Page 5 INSTALL THE RANGEHOOD 1 Remove the unit from the carton and place on a flat surface for assembly Cover the surface to prevent accidental damage Remove all parts including the mounting hardware before discarding the carton 2 Remove the grease filters USING TWO HANDS one to hold the filter so that it doesn t fall on cooktop and one to turn the knob by pulling the knob out and turning to the left 3 Therangehoodis shipped from the factory in the up vent position as indicated in FIGURE
7. PRO MAGNUM F2 FABER Wall Mount Canopy Rangehood Installation Instructions Use and Care Information READ AND SAVE THESE INSTRUCTIONS The Installer must leave these instructions with the homeowner The homeowner must keep these instructions for future reference and for local electrical inspectors use READ THESE INSTRUCTIONS BEFORE YOU START INSTALLING THIS RANGEHOOD WARNING TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE a Never leave surface units unattended at high settings Boilovers cause smoking and greasy spillovers that may ignite Heat oils slowly on low or medium setting b Always turn hood ON when cooking at high heat or when flambeing food i e Crepes Suzette Cherries Jubilee Pepper corn Beef Flamb c Clean ventilating fans frequently Grease should not be allowed to accumulate on fan or filter d Use proper pan size Always use cookware appropriate for the size of the surface element WARNING TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE OBSERVE THE FOLLOWING SMOTHER FLAMES with a close fitting lid cookie sheet or metal tray then turn off the burner BE CAREFUL TO PREVENT BURNS If the flames do not go out immediately EVACUATE AND CALL THE FIRE DEPARTMENT NEVER PICK UP A FLAMING PAN You may be burned DO NOT USE WATER including wet dishcloths or towels a violent steam explosion will result Use an extinguisher ONLY if 1 You know you have a Class ABC extinguisher and
8. cuit La taille du fusible doit se conformer aux codes municipaux suivant la sp cification lectrique sur la plaque int rieure Le diam tre du fil devra aussi se conformer aux r glements du code national lectrique ANSI NFPA 70 ainsi qu aux r glements locaux et les sp cifications de cet appareil On peut obtenir ces informations chez l Association Nationale de la Pr vention du Feu Batterymarch Park Quincy Massachusetts 02269 Raccordez cet appareil directement au coupe circuitavecunfil flexiblle couvert en cuivre en laissantun peu de l chement dans le fil pour permettre le d placement de l appareil Veillez a ce qu un contact d un demi pouce 1 2 po soit install chaque bout de fil soit l appareil ainsi qu la boite fusible Faites un trou de 1 1 4 po dans le mur S il s agit d un trou en bois sablez le bien tandis qu un trou passant par le m tal demande un bouche trou AVERTISSEMENT POUR R DUIRE LE RISQUE D INCENDIE OU DE CHOC ELECTRIQUE ne pas utiliser ce ventilateur en conjonction avec un dispositif de r glage de vitesse semi conducteurs AVERTISSEMENT POUR MINIMISER LES RISQUES D INCENDIE CHOC ELECTRIQUE OU DOMMAGES CORPORELS OBSERVER LES PRESCRIPTIONS SUIVANTES Suivez les recommandations du fabricant et entre en communication avec lui pour toute information Fermez le courant avant tout entretien et veillez a ce qu il reste ferm Si on ne peut pas verrouiller le panneaux du
9. cy Massachusetts 02269 For residential use only This appliance should be connected directly to the fused disconnect or circuit breaker through flexible armored or nonmetallic sheathed copper cable Allow some slack in the cable so the appliance can be moved if servicing is ever nec essary AUL Listed 1 2 conduit connector must be provided at each end of the power supply cable at the appliance and at the junction box When making the electrical connection cut a 1 1 4 hole in the wall A hole cut through wood must be sanded until smooth A hole through metal must have a grommet WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK do not use this fan with any solid state speed control device WARNING TO REDUCE THE RISK OF FIRE ELECTRI CAL SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING Use this unit only in the manner intended by the manufacturer If you have any questions contact the manufacturer Before servicing or cleaning unit switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a prominent warning device such as a tag to the service panel CAUTION For General Ventilating Use Only Do Not Use To Exhaust Hazardous or Explosive Materials and Vapors WARNING TO REDUCE THE RISK OF FIRE ELECTRI CAL SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING Instal
10. e Make sure there is proper clearance within the wall or floor for exhaust duct before making cutouts Do not cut a joist or stud unless absolutely necessary If a joist or stud must be cut then a supporting frame must be constructed FOR MORE SPECIFIC DUCTWORK INFORMATION GO TO PAGE 4 WARNING To Reduce The Risk Of Fire Use Only Metal Ductwork A WARNING Venting system MUST terminate outside the home DO NOT terminate the ductwork in an attic or other enclosed space DO NOT use 4 laundry type wall caps Flexible type ductwork is not recommended DO NOT obstruct the flow of combustion and ventilation air Failure to follow venting requirements may result ina fire ELECTRICAL REQUIREMENTS A 120 volt 60 Hz AC only electrical supply is required on a separate 15 amp fused circuit A time delay fuse or circuit breaker is recommended The fuse must be sized per local codes in accordance with the electrical rating of this unit as specified on the serial rating plate located inside the unit near the field wiring compartment THIS UNIT MUST BE CONNECTED WITH COPPER WIRE ONLY Wire sizes must conform to the requirements of the National Electrical Code ANSI NFPA 70 latest edition and all local codes and ordinances Wire size and connections must conform with the rating of the appliance Copies of the standard listed above may be obtained from National Fire Protection Association Batterymarch Park Quin
11. e house fuse blown If the unit still does not operate disconnect the power supply and check that the wiring connections have been made properly Version 12 04 Page 6 WARRANTY amp SERVICE All Faber products are warranteed against any defect in materials or workmanship for the original purchaser for a period of 1 year from the date of original purchase This warranty covers labor and replace ment parts The warranty does not cover consumable parts such as filters and light bulbs This warranty does not apply if this product has been subjected to faulty installation misuse or neglect This warranty excludes any consequential expense or damage resulting from any use or malfunction of the product All implied warranties are limited to the duration of this warranty To obtain warranty service contact the dealer from whom you pur chased the rangehood or the local Faber distributor If you cannot identify a local Faber distributor contact us at 508 358 5353 for the name of a distributor in your area WIRING DIAGRAM FOR 30 amp 36 MODELS 8 BS 50K A120 GRY gt 8 BS 50K A120 44 MLT WIRING BOX P NVA 120 VAC LINE IN This rangehood uses 20 watt Halogen Lamps USE AND CARE INFORMATION This rangehood system is designed to remove smoke cooking vapors and odors from t
12. e rangehood canopy from the screws Due to the weight of the canopy these screws must be installed into solid material Once the canopy is hung rotate the screw marked V1 to secure the rangehood to the wall MAKE SURE THAT THE RANGEHOOD IS SECURELY ATTACHED TO THE WALL FAILURE TO PROPERLY INSTALL COULD RESULT IN INJURY OR DAMAGE TO PROPERTY 8 The brackets shown in FIGURE 11 are also used to adjust the level of the canopy Using a Phillips screwdriver rotate the screw V2 to adjust the level of the canopy 9 Connect the Power Supply Cable to the rangehood Attach the White lead of the power supply to the White lead of the rangehood with a twist on type wire connector Attach the Black lead of the power supply to the Black lead of the rangehood with a twist on type wire connector Connect the Green Green and Yellow ground wire under the Green grounding screw 10 Replace the field wiring compartment cover and the grease filters 11 Iftheinstallation uses a telescopic chimney connect the ductwork and install the chimney Mount the upper chimney section to the wall first Then mount the lower section The lower section fits over the upper section If the installation uses a full width duct cover install it now 12 Turn the power supply on Turn on blower and light The rangehood controls are located on the right hand side under the canopy If the rangehood does not operate check that the circuit breaker is not tripped or th
13. en certifi ce que la hotte soit bien mise terre Faute de suivre ces recommandations pourrait occasionner un feu Uniquement pour usage menager Version 12 04 Page 3 TOOLS NEEDED FOR INSTALLATION Saber Saw or Jig Saw Drill 1 1 4 Wood Drill Bit Pliers Phillips Screwdriver Flat Blade Screwdriver Wire Stripper or Utility Knife Metal Snips Measuring Tape or Ruler Level Pencil Caulking Gun Duct Tape PARTS SUPPLIED FOR INSTALLATION 1 Hardware Package 1 Literature Package PARTS NEEDED FOR INSTALLATION 2 Conduit Connectors Power Supply Cable 1 Wall or Roof Cap All Metal Ductwork OPTIONAL ACCESSORIES AVAILABLE 30 High Backsplash 30 high mounts to the wall beneath the rangehood for a coordinated look part 620000095 30 model part 620000097 36 model part 620000098 48 model Telescopic Chimney Kit FIGURE 3 24 wide extends to accomodate 8 9 foot ceilings part 6097336 fits all size hoods Full Width Duct Cover FIGURE 4 12 high extends full width of the hood part 6097337 30 model part 6097338 36 model part 6097339 48 model Duct Transition Kit For 48 model only optional kit transitions two 3 1 4 x 10 openings to one 10 round opening part 6000002 Charcoal Filters it is highly recommended that professional style cooking always be vented to the outside for reciru lating installations
14. ere are four mounting screws Install the screws into the wall The screws should be inserted into the wall until the screw head is flush with the wall WARNING THE SCREWS PROVIDED FOR MOUNTING THIS RANGEHOOD MUST BE INSERTED INTO SOLID WOOD THESE MUST NOT BE INSERTED INTO SHEET ROCK If a backsplash is to be used with this rangehood it must be installed before the rangehood Installation instructions for the backsplash are supplied in its box The height of the backsplash will determine the bottom edge of the canopy 11 16 17 5 16 je _ Use only for 48 i se only for FIGURE 5 4 The Telescopic Chimney Kit and Full Width Duct Cover use different bracket systems to attach to the wall FIGURE 6 provides the position for the telescopic chimney brackets i i on 1 10 58 FIGURE 6 FIGURE 7 provides the dimensions for the Full Width Duct Cover brackets The Full Width Duct Cover also attaches to the top of the rangehood with screws provided The Full Width Duct Cover must be attached to the top of the rangehood before mounting the rangehood to the wall 26 15 16 32 15 16 44 15 16 11716 FIGURE 7 Determine the proper location for each bracket and install the brackets on the wall MAKE SURE THAT THE SCREWS AND BRACKETS ARE SECURELY FASTENED TO THE W
15. he cooktop area Rangehood Control Panel The control panel is located on the right hand side under the canopy The position and function of each control button are indicated in FIGURE 13 u Die LLM L M V FIGURE 13 Light On Off Button L On Off switch for the halogen lights Move the switch to 1 to turn the light ON and to 0 to turn it OFF Blower On Off Button M On Off switch for the blower Move the switch to 1 to turn the blower ON and to 0 to turn it OFF Blower Speed Button V Speed control for blower Move the switch to position 1 for LOW Speed 2 for MEDIUM speed and 3 for HIGH speed For Best Results Startthe rangehood several minutes before cooking to develop proper airflow Allow the unit to operate for several minutes after cooking is complete to clear all smoke and odors from the kitchen Cleaning The stainless steel grease filters should be cleaned frequently in hot detergent solution or washed in the dishwasher Clean exterior surfaces with acommercially available stainless steel cleaner Abrasives and scouring agents can scratch stain less steel finishes and should not be used to clean finished surfaces Replacing the Halogen Lamps Before you begin make sure that the rangehood is turned off and that the other lamps have had sufficient time to cool Halogen bulbs burn extremely hot and serious injury could result from touching a hot bulb To replace the lamp the bezel
16. it provoquer une inflammation et le g n ration de fum e Utiliser toujours une puissance de chauffage moyenne ou basse pour le chauffage d huile b Veiller toujours faire fonctionner le ventilateur de la hotte lors d une cuisson avec une puissance de chauffage lev e ou lors de la cuisson d un mets flamber i e Crepes Suzette Cherries Jubilee Peppercorn Beef Flamb c Nettoyer fr quemment les ventilateurs d extraction Veiller ne pas laisser de la graisse s accumuler sur les surfaces du ventilateur ou des filtres d Utiliser toujours un ustensile de taille appropri e Utiliser toujours un ustensile de taille adapt la taille de l l ment chauffant AVERTISSEMENT POUR PREVENIR LES BLESSURES EN CAS DE FEU SUIVRE LES RECOMMANDATIONS SUIVANTES ETOUFFEZ LE FEU avec un couvercle m tallique et fermez le br leur Si le feu ne s teint pas tout de suite QUITTEZ LES LIEUX ET APPELEZ LES POMPIERS NE TOUCHEZ JAMAIS UNE CASSEROLE EN FLAMMES N UTILISEZ JAMAIS DE L EAU ou un torchon mouill pour teindre le feu ce qui pourrait causer une explosion de vapeur N utilisez un extincteur que si 1 Vous avez un mod le ABC et vous connaissez bien son mode d emploi 2 Le feu est petit et peu r pandu 3 Les pompiers sont d j pr venus 4 Vous avez une sortie derri re vous TOUTE OUVERTURE DANS LE MUR OU LE PLANCHER PROXIMIT DE LA HOTTE DOIT TRE SCELL Gardez 24 po de hauteur entre le bas de la hotte et la surface
17. lation Work And Electrical Wiring Must Be Done By Qualified Person s In Accordance With All Applicable Codes And Standards Including Fire Rated Construction Sufficient air is needed for proper combustion and exhausting of gases through the flue chimney of fuel burning equipment to prevent backdrafting Follow the heating equipment manufacturer s guideline and safety standards such as those published by the National Fire Protection Association NFPA and the American Society for Heating Refrigeration and Air Conditioning Engineers ASHRAE and the local code authorities When cutting or drilling into wall or ceiling do not dam age electrical wiring and other hidden utilities Ducted fans must always be vented to the outdoors A WARNING Electrical ground is required on this rangehood If cold water pipe is interrupted by plastic nonmetallic gaskets or other materials DO NOT use for grounding DO NOT ground to a gas pipe DO NOT have a fuse in the neutral or grounding circuit A fuse in the neutral or grounding circuit could result in electrical shock Check with a qualified electrician if you are in doubt as to whether the rangehood is properly grounded Failure to follow electrical requirements may result in a fire Version 12 04 Page 2 R GLEMENTS D VACUATION Confirmer la sortie d vacuation soit par le mur soit par le toit Utilisez une longueur de tuyauterie minimale avecles moindres
18. nstalled with two different chimney options as well as without a chimney Before you begin installation you must determine which chimney installation will be used The Telescopic Chimney Kit is adjustable and designed to meet varying ceiling heights from 8 to 9 feet FIGURE 3 illustrates the dimensions of the rangehood with the optional Telescopic Chimney Kit FIGURE 4 illustrates the dimensions of the rangehood with the optional Full Width Duct Cover The body of the rangehood is the same dimensions regardless of the chimney option used WARNING BEFORE MAKING ANY CUTS OR HOLES FOR INSTALLATION DETERMINE WHICH VENTING METHOD AND CHIMNEY WILL BE USED AND CAREFULLY CALCULATE ALL MEASUREMENTS RANGEHOOD WITH TELESCOPIC CHIMNEY KIT oe W778 23 5 8 aae A FIGURE 3 29 78 35 718 147 7 8 RANGEHOOD WITH FULL WIDTH DUCT COVER 29 718 35 718 47 718 FIGURE 4 Version 12 04 Page 4 PREPARE THE WALL 1 Disconnect and move freestanding range from cabinet opening to provide easier access for installation Put a thick protective covering over cooktop set in range or countertop to protect from damage or dirt 2 Determine and clearly mark with a pencil the center line on the wall where the rangehood will be installed 3 The Pro Magnum attaches to the wall by mounting screws indicated in FIGURE 5 For the 30 and 36 models there are two mounting screws For the 48 model th
19. service lectrique affichez un avis de danger sur la porte AVIS Pour L vacuation G n rale Veillez Ne Pas Evacuer Des Mat riaux Ou Vapeurs Explosif AVERTISSEMENT POUR MINIMISER LES RISQUES D INCENDIE CHOC ELECTRIQUE OU DOMMAGES CORPORELS OBSERVER LES PRESCRIPTIONS SUIVANTES L installation Et Le Raccordement Electrique Doivent Se Faire Par Un Technicien Qualifi Selon Tous Les Codes Municipaux Afin d obtenir un rendement maximal en ce qui a trait la combustionainsi qu l vacuation des gaz par la conduite de chemin e une bonne a ration est n cessaire pour tous les appareils combustion Suivez les conseils et mesures de s curit du fournisseur tels que ceux publi s par l Association Nationale de la Sauvegarde contre l incendie et l Association Am ricaine d Ing nieurs de Chauffage Frigorifaction et Air Climatis ainsi que les codes municipaux En per ant un mur veillez ne pas perforer un autre fil lectrique Une ventilateur vacuation ext rieure doit tre raccord e l ext rieur AVERTISSEMENT Une prise terre est n cessaire pout cette hotte N utilisez pas un tuyau l eau froide pour la mise terre s il est branch un joint plastique non m tallique ou autre e NE JOIGNEZ PAS la mise terre conduit de gaz N INSTALLEZ PAS un fusible dans le circuit de mise terre ce qui peut causer une secousse lectrique V rifiez avec un lectrici
20. some ductwork is required to exhaust the unit out of the cabinet For 48 model order 2 kits one for each motor part 6093034 CALCULATE THE DUCTRUN LENGTH The ductrun should not exceed 35 equivalent feet if ducted with the required minimum of 3 45 Elbow 3 0 feet 1 4 by 10 rectangular duct or 55 equivalent 90 Elbow 5 0 feet feet if ducted with 10 round duct when 90 Flat Elbow 12 0 feet using Duct Transition Kit for 48 model Wall Cap 0 0 feet only Calculate the length of the ductwork by adding the equivalentfeet in FIGURE 1 for oies each piece of ductinthe system An example Ce is given in FIGURE 2 For best results use 9 Feet Straight Duct 9 0 feet no more than three 90 elbows Make sure 2 90 Elbows 10 0 feet that there is a minimum of 24 of straight Wall Cap 0 0 feet duct between elbows if more than one is Total System 19 0 feet used Do not install two elbows together FIG RE3 If you must elbow right away do it as far away from the hood s exhaust opening WARNING PERSONAL INJURY HAZARD Due to the weight and size of the rangehood canopy two or more people are needed to move and safely install the rangehood canopy Failure to properly lift rangehood could result in damage to the product or personal injury PLAN THE INSTALLATION This rangehood can be vented through the wall or ceiling To vent through a wall the blower must be turned to vent to the rear This rangehood can be i
Download Pdf Manuals
Related Search