Alpine KTC-211SH Car Monitor
Contents
1. 1 77 4N_PINE KTC 211PW 50 0385A 018 KTC 211SH 50 0385A 026 2000 SUBURBAN YUKON XL Overhead Console for use with Mobile Overhead Monitor INSTALLATION MANUAL These instructions are intended for use only by experienced professionals in the automotive customizing business Special tools and equipment as well as specialized handling and care of product during installation may be required Before beginning this installation carefully read through the following instructions Use extreme care when cutting headliner material Check for wiring or other componentry above headliner material Cut only where indicated Materials Tools required for this installation 1 Phillips screwdriver 2 Powered screwdriver or drill with adapter 3 Awl or scribe point tool or similar 4 Razor knife or similar tool 5 18 GA wire 4 6 Rubbing alcohol 7 ALPINE TMX R680A Mobile Overhead Monitor Jan 1 2001 INSTALLATION INSTRUCTION 44 0085A Printed in the U S A MATERIALS PROVIDED FOR INSTALLATION Description QTY 1 SCREW 6 x 3 8 PPH SCREW 10 X 1 2 HWH SCREW 8 32 X 1 1 2 PPH VELCRO TAPE 1 X 6 TEMPLATE FRONT MOUNTING BRACKET REAR MOUNTING BRACKET A C CONTROL MOUNTING BRACKET CONSOLE SWITCH SPDT SAAN AN WN le eS A N pj Jan 1 2001 INSTALLATION INSTRUCTION 44 0085A Printed in the U S A 1 Release front mounting clips of O E dome light by gently prying downward on front edge of ho2. D monitor housing Refer to wiring connections section of the TMX 680A owner s manual for details 9 Using a test light test function of lights 10 Install and route all video and audio cables and any other added component requirements to their PHOTO 6 respective places in the vehicle Refer to component installation instructions for wiring diagrams The suggested routing of the video system cable is as follows Above the headliner from video system to B pillar 5 Down the B pillar to the floor Route the power lead to an accessory controlled source Connect the ground lead to the vehicle chassis Route the remaining wiring to the VCP location See Photo 7 Connect per instructions included with the video system lll PREPARATION OF CONSOLE 11 Install O E A C control head in console item 8 pg 2 Remove protective backing from adhesive strips on mounting brackeBHREQ 8 pg 2 and press firmly against control head as shown See Photo 8 IV INSTALLATION OF CONSOLE Caution Use extra support for the console until secured to the vehicle Failure to do so may cause damage to console or installed components PHOTO 8 12 Install dome light switch item 10 pg 2 into opening on front of console Raise console into approximate position and connect A C control wires Insert bracket on rear of console into rear mounting bracket item 7 pg 2 and slide rearward Position console against headliner Make sure console align
3. ment is straight and matches contours in headliner then secure console using 2 two 6 x 3 8 screws item pg 2 through the slots in bracket on console into holes on front mounting bracket See Photo 9 13 Release LCD MBPS Rane from locked position Lower to viewing position for access to mounting 6 location in top of housing 14 Raise monitor housing into approximate position and connect all wiring to components Connect wiring and cabling per instructions included with LCD monitor 15 Check function of all component and lights See operating instructions for video operations check For further assistance refer to the TMX R680A owner s manual for the technical support phone number listed for your area 16 Insert monitor housing into opening in console Note Make sure wires do not get pinched between housing and console Align holes in housing with clips in mounting bracket Secure using 4 four 8 32 x 1 1 4 screws item 3 pg 2 See Photo 10 Caution Do not overtighten screws 17 Raise LCD monitor panel into locked position PHOTO 10 18 Cut Velcro tape item 4 pg 2 into 2 pieces Remove protective backing from tape and apply to remote controls Position them against the console door and press firmly on remote while holding the door 19 Raise remote control door into locked position PHOTO 11
4. using See Photo 1 PHOTO 1 2 Gently lower the front of housing enough to reach inside and push the A C control head out of the housing Disconnect wiring and lay control head in a safe place 3 Remove and discard 2 two screws which secure housing Disconnect wiring and discard light assembly See Photo 2 PHOTO 2 PHOTO 3 4 Using a razor knife carefully trim headliner as shown to allow clearance for mounting bracket See Photo 3 Locate template item 5 pg 2 at front edge of O E cut out Make sure that arrow is pointing forward and template is centered left to right in vehicle PHOTO 4 Squeeze clips on O E plastic bracket and pull downward Pull down on outer edges of bracket to release hook and loop fasteners Remove and discard plastic bracket See Photo 4 P E 6 Install front mounting bracket item 6 pg 2 by aligning holes in bracket with holes in O E roof brace Secure using 4 four 10 x 1 2 screws item 2 pg 2 See Photo 5 7 Use rubbing alcohol to clean sheet metal in rear area of headliner cut out Use a clean cloth to dry surface Remove protective backing from adhesive strips on rear mounting bracket item 7 pg 2 and position tab 18 1 4 from rear edge offrtrwgunting bracket Make sure bracket is centered left to right and firmly press against roof See Photo 6 8 Construct a 1ft jumper harness that will connect the vehicle s dome light wires to the lights in LC
Download Pdf Manuals
Related Search